USER MANUAL - Intellisteer
Contents
1. N s4 Red Crimp Connectors 18 22 GA 25A Inline fuse amp Fuse Holder i e 2 Mounting Screws 2 2 Tools required VOED ON iJ Medium 1 Phillips screwdriver for Receiver mounting screws e Multi meter for troubleshooting Hand crimp tool double action recommended 0 ame d OC15326 Rev A 6 2 3 Battery Installation or Replacement The pendant is powered by two A23 batteries supplied pre installed in pendant To replace these batteries e Remove two screws on back A of pendant e Turn over button side up and separate two halves of Remove pendant case screws e Install or replace the 2 E batteries noting the correct polarity Bring the two halves back together ensuring that the rubber keypad membrane is seated properly e Replace the two screws do not to over tighten e Dispose of old batteries properly If the unit will not be used for a long period of time it is recommended that the batteries be removed to prevent damage due to leakage from a discharged battery 7 MnfelliSte WIRELESS STEERING 2 4 Mounting Receiver The Receiver should be mounted where it has access to the drive unit wiring and a 12v power supply ideally close to the autopilot course computer if fitting to a boat with an autopilot system Although the Receiver is waterproof the location should not be exposed to the elements to protect the wiring connection from corrosion If this is not possi2. Equipment the Manual have been followed and subject always to the other provisions of this Agreement that the Equipment is free from defects in workmanship and materials under normal use and service and will perform substantially in accordance with the specifications set forth in the Manual Electronics are covered for a period of one 1 year from the date of purchase of the Equipment by 21 IntelliSt WIRELESS STEERING the Purchaser while the Drive Unit is covered for a period of two 2 years from the date of purchase of the Equipment by the Purchaser This Limited Warranty covers the cost of shop labor and materials when the defective Equipment are delivered to Canada Metal Pacific Ltd NOTICE OF DEFECT The Limited Warranty will not apply to any defective Equipment unless written notice of such defect is given to Canada Metal Pacific Ltd by mail to Customer Service at 7733 Progress Way Delta BC Canada V4G 1A3 or by facsimile to Canada Metal Pacific Ltd At 1 604 952 2650 and is received by Canada Metal Pacific Ltd Within ten 10 days of the date upon which the defect first become known to the Purchaser Notices sent by mail will be deemed to be received by Canada Metal Pacific Ltd on the seventh 7th day first following the date of posting in North America and on the tenth 10th day next following the date of posting anywhere else in the world Notices sent by facsimile will be deemed to be received
3. by Canada Metal Pacific Ltd on the date of transmission with appropriate answerback confirmation WARRANTY LIMITATIONS The Limited Warranty shall not be effective and shall be void if the Equipment or its components are i not installed or used under normal conditions as recommended by Canada Metal Pacific Ltd ii subjected to abuse neglect or carelessness iii altered or repaired by anyone not authorized by Canada Metal Pacific Ltd during the term of this Limited Warranty iv subjected to all non pleasure use v subjected to use exceed ing twelve 12 volt v direct current dc vi subjected to use exceeding vessel trolling speeds This Limited Warranty does not cover and Canada Metal Pacific Ltd is not responsible for structural elements of the vessel upon which the Equipment is installed or any electrical or mechanical fittings or components not supplied by Canada Metal Pacific Ltd Canada Metal Pacific Ltd is not responsible for the proper installa tion of the Equipment or its supporting components and it is the re sponsibility of the Purchaser to ensure that the supporting elements and the Equipment s connection thereto are properly engineered The Purchaser shall periodically inspect all structural and supporting elements of the vessel and Equipment for signs of wear corrosion and or visible deterioration The Purchaser shall discontinue use of the Equipment at the first indication of deteriorati
4. 0 Voltage Drop 12 VOLTS 2 2 2 W EO me el AL vr OU Va ee ne we eee waa f e e n OM NM OM NO MO 8 8 8 8 8 G AE ee AO ee G Mie Ie vei ot oe VA oe bed ed Hi wl eed vaar Ro Deed BECKER sae e u 1 n e ane o s a bt t e tt OC15326 Rev A 12 2 9 Verify Installation e Check that the mounting and all connections are tight and secure Turn on the system with the Pendant On Off button Press the L or R buttons and ensure that the boat steers in the correct direction if not reverse the polarity of the drive connections e If you are interfacing with an Autopilot course computer turn the Pendant off and ensure that the Autopilot operates correctly as normal Any problems likely relate to the polarity of the clutch or drive connections refer to the troubleshooting guide Once you have verified the installation you should familiarize yourself with the operation of the Intellisteer Wireless Controller while at the dock 3 Infelli feer WIRELESS STEERING 3 Operation The Intellisteer Wireless System can be used for steering control while trolling or more generally as a second steering station on the boat IMPORTANT It is critical that the operator keeps a watch for hazards at all times while underway it is the operator s responsibility to ensure safe navigation of the vessel 3 1 Power On Off If interfaced with an Autopilot the Autopilot must be turned off or put into standby mode befor
5. USER MANUAL Revision A 25 05 2013 Revision History Description A First edition 2013 Canada Metal Pacific Limited All rights reserved The information contained in this document is the sole property of Canada Metal Pacific Limited Any reproduction in part or whole without the written permission of Canada Metal Pacific Limited is prohibited Canada Metal Pacific Limited will nor be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this document To the best of our knowledge the information in this document was correct at the time it was produced However Canada Metal Pacific Limited cannot accept liability for any inaccuracies or omissions it may contain In addition our policy of continuous product im provement may change specifications without notice As a result Canada Metal Pacific Limited cannot accept liability for any differences between the product and this document Please visit www intellisteer com to ensure you have the most up to date version of the documentation for your product CONTENTS Introduction Installation Included Parts Tools Required Battery Installation or Replacement Mounting Receiver Crimp Connections Connecting To A Standalone Drive Unit Connecting To An Autopilot System Power Cable Gauge Recommendation e 12 Veri
6. ble all connections should be protected using adhesive heatshrink sleeving Intellisteer Receiver Mount the receiver using the two self tapping screws supplied 2 5 Crimp Connections Positive crimp connections are critical to reliable operation ensure that the stripped wires are fully inserted into the crimp and that the crimp is fully made Using a double action hand crimping tool will give the best results although a standard single action crimp can work well if used correctly Pull lightly on the wires after crimping to ensure a positive connection 2 6 Connecting To A Standalone Drive Unit Typically there are 4 wires from a steering drive unit two heavy wires to drive the motor and two lighter wires to actuate the clutch for a mechanical drive or bypass solenoid for a hydraulic drive if required Some drives do not have a clutch refer to your drive instructions for confirmation OC15326 Rev A 8 Cut back and strip the drive input and clutch wires from the drive unit and connect to the Intellisteer Receiver as shown in Table 1 using the supplied crimp connectors If the steering direction does not match that indicated on the Pendant the drive input wires can be reversed See Troubleshooting section for more details Drive clutches do not usually have a polarity and the two wires can be connected either way round If the drive does indicate a polarity match to the clutch input on the Intellisteer Receiver to Driv
7. ctivated Try steering in the other direction to reset the overload protection Clutch does not operate correctly when Intellisteer is steering e Check Intellisteer clutch output polarity and correct if reversed the clutch on most autopilot drive units is not polarity sensitive however some are Clutch operates correctly when Intellisteer is steering but not when the Autopilot is Check Intellisteer clutch input polarity and correct if reversed Steering is Reversed on Intellisteer Operation Reverse drive polarity between the Intellisteer Receiver and the drive unit Steering is Reversed on Autopilot Operation Reverse drive polarity between the course computer and the Intellisteer Receiver No communication between Pendant and Receiver Re pair Pendant and Receiver There may be signal interference if the boat has steel bulkheads decks or there are other metallic objects between the Pendant and Receiver Consider relocating the Receiver to a place where there is no metal blocking the signal 19 MInfehli feer WIRELESS STEERING 4 3 Specification Wireless Controller amp Receiver Frequency 315MHz or 433 92 MHz Meets FCC CE and BS EN 60945 2002 EMC standards Operating temperature range 30C to 80C Handheld and receiver can be paired in field Pendant and receiver auto off in 30 minutes if no usage Over 1 Million control codes provide enhanced security Handheld Pendant Water resistant Supplied with 2
8. e Unit Clutch 1 and to Drive Unit Clutch 2 Fit the supplied inline fuse to the 12V wire and connect the ground line directly to the Intellisteer Receiver ground wire Intellisteer Steering Intellisteer Receiver Drive Connection Receiver es EE IT Bue Drive Unit Input Drive Unit Input Orange Drive Unit Clutch 1 N ruse i Drive Unit Clutch 2 ai Table 1 12v DC NOTE For a standalone drive installation the 4 Course Com puter wires Yellow Yellow Green Brown Pink are not used and should be wrapped with electrical tape and secured gt durellisteer 2 7 Connecting To An Autopilot System Typically there are 4 wires between the autopilot course computer and drive unit two heavy wires to drive the motor and two lighter wires to actuate the clutch for a mechanical drive or bypass solenoid for a hydraulic drive if required Some drives do not have a clutch refer to your drive instructions for confirmation Disconnect the drive output and clutch wires from the course computer and connect these to the corresponding drive unit input and drive unit clutch wires on the Receiver as per Table 2 using the supplied crimp connectors Connect the Course Computer Drive Output and Course Computer Clutch wires from the Receiver to the corresponding connectors on the course computer refer to your autopilot manual for the wire co
9. e activating the Intellisteer Wire less Controller to prevent interactions between the two controllers If both Intellisteer and the Autopilot are steering at the same time unpredictable results can occur Press the black ON OFF button on the Pendant to activate the Intellisteer ove Wireless System The LED will turn red for approximately 2 seconds during initialization then flash once every two seconds to indicate that the system is operational When the Intellisteer Wireless System is on the pendant jog steering buttons are active OC15326 Rev A 14 When the L or R button is pushed the clutch is engaged and the drive is activated The LED indicator flashes continuously while the steering buttons are pressed and the Pendant is transmitting When the button is released the clutch is disengaged and manual steering is re enabled Press ON OFF to power off the Intellisteer and return to normal operation the pendant LED will stop flashing and the autopilot will be reconnected 3 2 Steering With the system powered on press L or R on the pendant to steer the boat to the Left or Right As long as L or R is depressed power will be supplied to the drive unit and it will keep steering ONOFF gt further in the indicated direction until the button is released To return the steering to straight ahead it will be necessary to centre the rudder by pressing the opposite button until the boat is steering st
10. e other OC15326 Rev A 16 4 Adding Or Replacing A Pendant Your Intellisteer Pendant and the Receiver are paired using a unique code ensuring that only your Pendant will control your Receiver The Pendant and Receiver are paired at the factory and are ready to use out the box The Intellisteer Receiver can be paired with two Pendants at the same time in which case it can be controlled by either one If the user attempts to pair with a third Pendant it will take the place of the first Pendant paired only two Pendants can be paired at a time 4 1 Pairing Pendant To Receiver 1 2 Turn the Pendant on Disconnect power to the Receiver remove inline fuse turn off breaker etc Wait 10 seconds then reconnect power to the Receiver Within 5 seconds of restoring power to the Receiver press both the L and R buttons on the Pendant at the same time Immediately after pressing both the L and R buttons press the On Off button twice in succession The units are now paired 17 Infelli teer LESS STEERING 5 Appendix 5 1 Warnings Always maintain a permanent watch this will allow you to respond to situations as they develop Failure to maintain a permanent watch puts yourself your vessel and others at serious risk of harm This product must be installed and operated in accordance with the instructions provided Failure to do so could result in personal injury damage to your vessel and or p
11. fy InstallatiON ee ee ee EA ee AR 13 Operation es eas N esse ER ees Power On Off Steering Auto Shut Off Overload Protection ee se ee ee Ee ee 16 Adding Or Replacing A Pendant Pairing Pendant To Receiver Appendix Warnings Troubleshooting Specification FCC CE Statements Limited Warranty 21 Infelli te WIRELESS STEERING 1 Introduction Congratulations on your purchase of an Intellisteer Wireless Controller This simple yet powerful system is designed to free you from the need to hand steer your boat from the helm providing wireless jog steering control from anywhere on your boat There is an Intellisteer model suitable for almost any boat Whether you have cable or hydraulic steering with an autopilot or without Intellisteer has a configuration that can provide you with the freedom of wireless steering This manual covers the installation and operation of the standalone version of the Intellisteer designed to interface with an existing autopilot and drive installation whether or not the existing course computer is operational As long as the drive unit is functional Intellisteer can control it OC15326 Rev A 4 If you do not have an existing autopilot installation there are other Intellisteer system packages which bundle the wireless controller with a specially designed steering drive unit These include e Intellisteer Type R provides remote steering f
12. lour coding between the autopilot course computer and drive unit Autopilot drive clutches do not usually have a polarity and the two wires can be connected either way round If the autopilot clutch output does specify a polarity connect Course Computer Clutch Output to Course Computer Clutch 1 on Receiver and Drive Unit Clutch 1 to clutch input on Drive Fit the supplied inline fuse to the 12V wire and connect the ground line directly to the Intellisteer Receiver ground wire NOTE Additional crimp connectors are supplied if it is not possible to locate the Receiver close enough to the course computer to be wired directly to it as described above and it is necessary to splice the Receiver into the middle of the wiring run OC15326 Rev A 10 Intellisteer Receiver Oe ees LL UF Course Autopilot Yellow Course Computer Drive Output Yellow Course Computer Gieen Drive Output U ene oreina Table 2 tellisteer eceiver gt D no Infeli feer WIRELESS STEERING 2 8 Power Cable Gauge Recommendations As power to the drive unit is supplied by the Intellisteer Receiver when operating it is recommended that a minimum of 14GA wire be used for the power connection Heavier gauge wire may be required for longer runs and or larger drive units Refer to the table below for wire gauge recommendations Conductor Sizes Gauge for 1
13. on The Limited Warranty shall not be valid except when delivered by an authorized dealer representative or installing boat builder or shipyard and the Purchaser shall not be entitled to rely on any other representations or warranties whether oral or written except as provided in this limited warranty THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES ANY WARRANTY IMPLIED BY STATUTE AND NOT EXCLUDED HEREIN INCLUDING WARRAN TIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS IN EFFECT ONLY DURING THE DURATION OF THE EXPRESS WARRANTY SET FORTH HEREIN This warranty gives the Purchaser specific legal rights and the Purchaser may also have other rights which may vary from country to country or state to state This warranty shall be constructed pursuant to the laws of the Province of British Columbia Mnfelli teer IntelliSteer is a registered trade mark of Canada Metal Pacific Ltd 7733 Progress Way Delta BC Canada V4G 1A3 Tel 1 604 940 2010 Fax 1 604 952 2650 Web www intellisteer com E mail octopus canmet com
14. oor product performance In the event of UNCONTROLLED remote steering or other EMERGENCY situations return to MANUAL steering is pro vided by turning the Intellisteer System OFF with the Pendant On Off button If this is not practical the helm can be forced to one side or the other to manually override the autopilot drive and power to the Receiver should be removed as quickly as possible It is STRONGLY advised that the helmsman be formally familiarized with this OVERRIDE procedure Do NOT install in a location where it will be exposed to a hazardous flammable atmosphere such as near fuel tanks Some autopilot drives connect directly to the helm wheel and incorporate a manual clutch release While this clutch is engaged it may be difficult or impossible to manually override the autopilot drive For this type of installation users should familiarize themselves with the use of the clutch release so as to allow quick return to manual control in the event of an emergency OC15326 Rev A 18 5 2 Troubleshooting Pendant does not operate correctly LED indicator not operating normally Check or replace Pendant batteries Receiver is not operating Check or replace 25A inline fuse Check power supply polarity and correct if it is reversed The receiver is protected against reverse polarity and no damage will result However the unit will not operate if the power supply leads are reversed Overload protection may have been a
15. or auxiliary or primary outboards or even sterndrives e Intellisteer Type S provides a helm replacement for remote steering of cable steered boats e Intellisteer Type T provides a helm replacement for remote steering of cable steered boats with tilt steering e Intellisteer Type H provides remote steering for hydraulically steered boats Instructions covering the installation of these Intellisteer steering drives is included with the drive units in the system kits More information can be found at www intellisteer com 5 MInfeliSt WIRELESS STEERING 2 Installation The Intellisteer Wireless Controller is designed to be used with any reversing steering drive unit requiring less than 25A peak operating current whether mechanical or hydraulic While Intellisteer can be integrated with an Autopilot Course Computer it does not require one to operate It is not suitable for use with all in one cockpit autopilots with an integrated course computer It is also not suitable for use on boats with a positive ground system It should not be fitted to boats where the maximum horsepower of the engines exceeds the maximum horsepower rating for the vessel as stated on the vessel manufacturers tag 2 1 Included Parts Before installation check your kit includes all required parts Intellisteer Wireless Receiver Intellisteer Wireless Pendant TE 00 Pendant Lanyard 7 Blue Crimp Connectors 14 16GA a
16. raight ahead With practice quite precise steering control can be achieved 5 Infelli feer SS STEERING 3 3 Auto Shut off If the Intellisteer is not used for 30 minutes the Pendant will automatically power down to save battery life To re activate the Pendant simply press the ON OFF button 3 4 Overload Protection To prevent electrical or mechanical damage in the event that the drive unit is driven all the way to one end of the steering system travel the Intellisteer Receiver incorporates overload protection If the drive unit hits the stops and can go no further but power continues to be applied the Intellisteer Receiver will disconnect power to the drive unit To reconnect power to the drive unit simply steer the boat in the other direction Hydraulic pumps have higher current demands than mechanical drives and can generate large current spikes when the steering direction is quickly reversed In this situation rapidly changing steering direction back and forth between L and R with no pause between the button pushes can cause large current spikes which may trigger the overload protection circuit If this occurs simply wait for 1 second then steer the boat in the other direction from the last button push This will reset the overload circuit To prevent this accidental activation of the overload protection circuit with hydraulic systems simply wait for 1 second between releasing one steering button and pushing th
17. x 23A batteries Wireless Receiver amp Motor Controller Waterproof Motor drive capability up to 25A Over load protection Reverse polarity protection 12VDC nominal 9 16V DC operating range Offers pass through capability for Autopilot motor and clutch control circuits Can be controlled by up to two Pendants OC15326 Rev A 20 4 4 FCC CE Statements The Intellisteer Wireless Controller complies with the FCC Code of Federal Regulations Title 47 Part 15 regarding unlicensed transmissions e This device will not cause harmful interference with other equipment e This device must accept any interference received including interference which may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment This equipment gener ates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications 4 5 Limited Warranty Canada Metal Pacific Ltd manufacturer of IntelliSteer and associated products warrants the original end user the Purchaser provided that the recommended installation and maintenance procedures set forth in the manual that has been provided with the
Download Pdf Manuals
Related Search