Home
DMX_Splitter IP65_User_man_eng_v1-0
Contents
1. Se nS USER MANUAL COMPANY NA STAGE amp LIGHT Company NA 9 Wambertu Stk Marupe LV 2167 Latvia Phone 371 6780 1111 O ajae gt OO eMail na na lv www na lv TABLE OF CONTENTS BEER YOU BEGIN u LS a aaa aaia eaa Ea aa aaae 3 WHAT IS INCLUDED UNPACKING INSTRUCTIONS AC POWER CONTACT US SAFETY INSTRUCTIONS 2 INERODUCTION G Aa a 5 FEATURES Description PRODUCT OVERVIEW FUSE REPLACEMENT FIXTURE LINKING Data Cabling DMX Data Cable Cable Connectors 3 Pin to 5 Pin Conversion Chart SETTING UP A DMX SERIAL DATA LINK MOUNTING Orientation 4 OPERATING INSTRUCTIONG 8 Operating Signal processing DMX Splitter output connection to input LED indicator positions SEENEN eege a EEN 10 DMX PRIMER GENERAL MAINTENANCE RETURNS PROCEDURE CLAIMS TECHNICAL SPECIFICATIONS DMX Splitter IP65 User Manual version 1 0 06 2011 1 BEFORE YOU BEGIN What is included gt 1 x DMX Splitter IP65 unit gt 1 x Warranty Card gt 1 x Users Manual Unpacking Instructions Immediately upon receiving a unit carefully unpack the carton check the contents to ensure that all parts are present and have been received in good condition Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton it self shows signs of mishandling
2. DMX curve At this outputs signal processing signal delay is 0 1 usek At the first DMX output signal processing is not performed DMX Splitter IP65 User Manual version 1 0 06 2011 LED indicator positions COMPANY DMX SPLITTER IP65 NA STAGE amp LIGHT vvvvvv na lv Manufactured in EU Voltage 85 265 VAC Frequency 47 63 Hz Power 7 5 Watts Input Output isolation Optical up to 1000V POWER Power LED indicator green has two positions e Off Power is not connected e On Power is connected DATA DMX input signal LED indicator is located at the top of the unit and indicate whether the DMX signal recieve at the input DMX input signal LED indicator yellow has two positions e Off DMX signal is not received e Blink DMX signal is recieved DMX Splitter IP65 User Manual version 1 0 06 2011 5 APPENDIX DMX Primer There are 512 channels in a DMX 512 connection Channels may be assigned in any manner A fixture capable of receiving DMX 512 will require one or a number of sequential channels The user must assign a starting address on the fixture that indicates the first channel reserved in the lighting console There are many different tyoes of DMX controllable fixtures and they all may vary in the total number of channels required Choosing a start address should be planned in advance Channels should never overlap If they do this will result in erratic operation of the fixtures whose st
3. transmit DMX data reliably over long distances The cable will have the following characteristics 2 conductor twisted pair plus a shield Maximum capacitance between conductors 30 pF tt Maximum capacitance between conductor and shield 55 pF tt Maximum resistance of 20 ohms 1000 ft Nominal impedance 100 140 ohms DMX Splitter IP65 User Manual version 1 0 06 2011 CABLE CONNECTORS Cabling must have a male XLR connector on one end and a female XLR connector on the other end DMX connector configuration 1 SHIELD OUTPUT 4 Not connected 4 O O2 Termination reduces signal errors To 5 Not connected 3 avoid signal transmission problems and interference it is always advisable to connect a DMX signal terminator Resistance 120 ohm 1 4w between pin 2 DMX and pin 3 DMX of the last fixture CAUTION Do not allow contact between the common and the fixture s chassis ground Grounding the common can cause a ground loop and your fixture may perform erratically Test cables with an ohm meter to verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each other 3 PIN TO 5 PIN CONVERSION CHART NOTE If you use a console with a 5 pin DMX output connector you will need to use a 5 pin to 3 pin adapter The chart below details a proper cable conversion 3 PIN TO 5 PIN CONVERSION CHART Conductor 5 Pin Male Input Ground Shield Pin 1 Data sign
4. Save the carton and all packing materials In the event that a unit must be returned to the factory it is important that the unit be returned in the Original factory box and packing AC Power The only thing necessary to do before powering on the unit is to make sure the line voltage you are applying is within the range of accepted voltages This unit will accommodate 85 265V AC 47 63 Hz All units must be powered directly off a switched circuit and cannot be run off a rheostat variable resistor or dimmer circuit even if the rheostat or dimmer channel is used solely for a 0 to 100 switch Contact Us General Information Company NA 9 Lambertu street Marupe LV 2167 Latvia Phone 371 6780 1111 Fax 371 6755 6505 e mail na na lv web Wwww na lv DMX Splitter IP65 User Manual version 1 0 06 2011 3 Safety Instructions Caution Please read these instructions carefully which includes important information about the installation usage and maintenance of this product Please keep this User manual for future consultation If you sell the unit to another user be sure that they also receive this instruction booklet Always make sure that you are connecting to the proper voltage and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the unit Make sure there are no flammable materials close to the unit while operating Always disconnect from power source before servic
5. a 1 unit tail Neutrik NC5 MX HD male socket DMX e fro u uu y a L usuy 1 4 units Neutrik NC5 FX HD female socket DMX pin config pin 1 shield pin 2 pin 3 pin 4 don t use pin 5 dont use C OI OL EEN DMX 512 Signal delay in processing mode 0 1 usec WARRANTY INFORMATION Waral tyuuna ete ee ae tas 2 year limited warranty DMX Splitter IP65 User Manual version 1 0 06 2011 12
6. al Pin 2 Data signal Pin 3 Do not use Se Do not use Do not use SY Do not use Setting up a DMX Serial Data Link 1 Connect the male connector side of the DMX cable to the output female connector of the lighting concole DMX 512 Lighting console 2 Connect the end of the cable coming from the lighting console which will have a female connector to the input connector of the DMX Splitter consisting of a male connector 3 Then proceed to connect from the output as stated above to the input of the following Continue DMX Linking fixture and so on DMX Splitter IP65 User Manual version 1 0 06 2011 7 Mounting ORIENTATION This unit may be mounted in any position 4 OPERATING INSTRUCTIONS Operating DMX Splitter IP65 has two types of DMX outputs one output without optical isolation four outputs with optical isolation up to 1000V Signal processing DMX signal splitter is used for standard DMX 512A signal amplification and splitting to multiple outputs The splitter has 1 optically isolated DMX input 1 through output and 4 optically isolated outputs Available with hard wired data connectors or tail Neutrik NC5 M F X HD series data connectors This unit provide the DMX signal reinforcement at the outputs 2 5 Upon receipt of DMX signal it is recorded in device memory and then straightened the signal distortion components Then at the DMX Splitter IP65 output is fed DMX signal with the proper
7. arting address is set incorrectly You can however control multiple fixtures of the same type using the same starting address as long as the intended result is that of unison movement or operation In other words the fixtures will be slaved together and all respond exactly the same DMX fixtures are designed to receive data through a DMX Chain A DMX Chain connection is where the DMX OUT of one fixture connects to the DMX IN of the next fixture The order in which the fixtures are connected is not important and has no effect on how a lihgting console communicates to each fixture Use an order that provides for the easiest and most direct cabling Connect fixtures using shielded two conductor twisted pair cable with three pin XLR male to female connectors The shield connection is pin 1 while pin 2 is Data Negative S and pin 3 is Data positive S Company NA carries 3 pin and 5 pin XLR DMX compliant cables General Maintenance To maintain optimum performance and minimize wear fixtures should be cleaned frequently Usage and environment are contributing factors in determining frequency As a general rule fixtures should be cleaned at least twice a month Dust build up reduces light output performance and can cause overheating This can lead to reduced lamp life and increased mechanical wear Be sure to power off fixture before conducting maintenance Unplug fixture from power Use a vacuum or air compressor and a soft brush to remove dust col
8. for standard DMX 512A signal amplification and splitting to multiple outputs The splitter has 1 optically isolated DMX input 1 through output and 4 optically isolated outputs Available with hard wired data connectors Product Overview DMX input signal LED indicator Corps closing screw POWER LED indcator Corps closing screw Opticaly isolated DMX outputs Throught DMX output Corps closing Opticaly isolated screw DMX input DMX Splitter IP65 User Manual version 1 0 06 2011 5 3 SETUP Disconnect the power cord before replacing a fuse and always replace with the same type fuse Fixture Linking You will need a DMX data link to run light shows of one or more fixtures using a DMX 512 lighting console The combined number of channels required by all the fixtures on a DMX data link determines the number of fixtures the DMX data link can support Important Fixtures on a DMX data link must be daisy chained in one single line To comply with the EIA 485 standard no more than 32 devices should be connected on one data link Connecting more than 32 fixtures on one serial data link without the use of a DMX optically isolated splitter may result in deterioration of the digital DMX signal Maximum recommended DMX data link distance between fixtures 300 meters 984 ft DMX DATA CABLE Use a Belden 9841 or equivalent cable which meets the specifications for EIA RS 485 applications Standard microphone cables cannot
9. ing or replacing fuse and be sure to replace with same fuse source Secure unit to fastening device using a safety chain Maximum ambient temperature Ta is 40 C Do not operate unit at temperatures higher than this In the event of a serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts Don t connect the device to a dimmer pack Make sure the power cord is never crimped or damaged Never disconnect the power cord by pulling or tugging on the cord Avoid direct eye exposure to the light source while it is on There are no user serviceable parts inside the unit Do not open the housing or attempt any repairs yourself In the unlikely event your unit may require service please contact Company NA at 371 6780 1111 DMX Splitter IP65 User Manual version 1 0 06 2011 4 2 INTRODUCTION Features e DMX 512 IP65 signal splitter e DMX inputs 1 e DMX outputs 1 4 e P65 protected housing e There are 2 LED status indicators Additional Features e Available in silver e Optional IP65 protected DMX connectors Neutrik NC5 F M HD Description The Company NA manufactured DMX IP65 signal splitter is designed for outdoor use from very cold to very hot conditions and it is IP65 rated DMX signal splitter is used
10. lected on external vents and internal components Clean all glass when the fixture is cold with a mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue Apply solution to the cloth or tissue and drag dirt and grime to the outside of the lens Gently polish optical surfaces until they are free of haze and lint The cleaning of internal and external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit s optics Clean with soft cloth using normal glass cleaning fluid Always dry the parts carefully Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days DMX Splitter IP65 User Manual version 1 0 06 2011 10 Returns Procedure Claims Returned merchandise must be sent prepaid and in the original packing call tags will not be issued Package must be clearly labeled with a Return Merchandise Authorization Number RMA Products returned without an RMA will be refused Call Company NA and request RMA prior to shipping the fixture Be prepared to provide the model number serial number and a brief description of the cause for the return Be sure to properly pack fixture any shipping damage resulting from inadequate packaging is the customer s
11. responsibility Company NA reserves the right to use its own discretion to repair or replace product s As a suggestion proper UPS packing or double boxing is always a safe method to use Note If you are given an RMA please include the following information on a piece of paper inside the box 1 Your name 2 Your address 3 Your phone number 4 The RMA 5 A brief description of the symptoms Damage incurred in shipping is the responsibility of the shipper therefore the damage must be reported to the carrier upon receipt of merchandise It is the customer s responsibility to notify and submit claims with the shipper in the event that a fixture is damaged due to shipping Any other claim for items such as missing component part damage not related to shipping and concealed damage must be made within seven 7 days of receiving merchandise DMX Splitter IP65 User Manual version 1 0 06 2011 11 DMX Splitter IP65 Technical Specifications WEIGHT amp DIMENSIONS POWER THERMAL Fe II WEE 295 0 mm ed Ee 215 0 mm EU eege eege 95 0 mm WY IGM EE 2 3 kg Operating Voltage E 85 265V AC 47 63 Hz Power GonsuUmpUON sussana aa a deeg 7 5W max Input QUTDUTISOIAUON EE Optical up to 1000 V Maximum ambient Temperature 50 C Minimum ambient temperature 40 C OG LINN strlen ees convectional Ligh ege e EE 65 CONTROL amp PROGRAMMING DMX INPUT eiren E
Download Pdf Manuals
Related Search
Related Contents
Popcorn Hour VTEN Manuale Utente votre nouveau vélo elliptique Chicago Electric 44829 User's Manual Vermont Casting C34G624M Fan User Manual Libros y Revistas recibidos Cotidiano Reseña de libros Valparaíso Toshiba 19EL834 Real-Time Multiprocessor Architecture for Sharing Stream Meade Video mySKY Plus User's Manual SIROLaser - Sirona Support Copyright © All rights reserved.
Failed to retrieve file