Duplicator Controller Functions User`s Manual Version: 1.1
Contents
1. 11 16 Quick Erase 11 17 Full Erase 11 18 Auto Close Tray 11 19 Quick Compare 11 20 Tray In Out 11 21 BootTime Delay 11 22 Start Tray Eject 11 23 Disc Redetect 11 24 Show Burn Speed Among the 11 functions Function 10 Edit Track is designed exclusively for editing a collection of favorite songs from CDs During operation if you don t understand an LCD message see Appendix A 2 1 Copy Function 1 Copy instant copy source disc image to the target drives optical writes Use Function 8 to select source drive before copying Select function 1 place a source disc into source drive and blank disc into the target drives A rewriteable disc can be used as target media however all data will be erased before copying 1 Copy Press ENT to start copy function when all discs are ready After complete system will show spent time and the amount of OK disc on the screen the OK disc will be ejected OK 01 Time 00 05 01 2 2 Test Function 2 copy simulation no data will be written to the write once media DVD R is not supported for this function 2 Test Press ENT to start simulation If rewriteable disc is used all contained data will be erased before simulation OK 01 Time 00 05 01 2 3 Test amp Copy Function 3 will do copy simulation before copy function 3 Test amp Copy Press ENT to2. Duplicator Controller Functions User s Manual Version 1 1 Attention Wait over 5 seconds to power on after shutdown to prevent the abnormal operation of the system Copyright 2011 CE FE Copyright and Trademarks The information of the products in this manual is subject to change without prior notice and does not represent a commitment on the part of the vendor who assumes no liability or responsibility for any errors that appear in this manual SySTOR is the trademarks of SySTOR Systems Inc This manual contains materials protected under International Copyright Laws All rights reserved No part of this manual may be reproduced transmitted or transcribed without the expressed written permission of the manufacturer and author of this manual SySTOR s Duplicator Controller is used for copying and editing personal audio and video data Violating Copy Right is a criminal act SySTOR s Duplicator Controller only supports legal backup operation SySTOR Systems Inc is not responsible for illegal recording Table of Contents Chapter The Panel 25 AR ARR a Chapter 2 FUNcions Lea ai O AIN ELIA ER EE E 23 NESK COPY EE ZANETTI EE DAMA A RR RR QO PreScan nie A A AT AE ZI DICO RR 28 Select Sourcen aiar PA D Ea AE ds LI A E I ata DL allietano EE 292 Delete Image ili a ge EE 2 9 3 Image Info sisi lO NO REATI a ates ee A OR i 2 9 4 el ME 2 9 5 Select Image nane LS Le ia 2 9 6 Image STE DAVE Lal
3. Eject All discs stay in after burning 11 9 Setup The default is Eject Good Only Eject Disc 2 11 10 Burn On The Fly Burn On The Fly means data will be copied directly from the source disc to the target disc When the setting is Off the data will be loaded into temporary partition of HDD first then copy from HDD to disc 11 11 Setup Burn On The Fly The default is On Press W to select Off 2 11 11 Burn Mode There are two modes DAO Disc At Once and TAO Track At Once 11 11 Setup Burn Mode The default is DAO Press Y to select TAO 17 2 11 12 Display Time To set if display a timer while copying 11 12 Setup Display Time The default is On Press Y to select Off 2 11 13 Button Sound To enable or disable beep sound while press a key 11 13 Setup Button Sound The default is On Press W to select Off 2 11 14 Device Info To show the writer information 11 14 Setup Device Info 2 11 15 System Info To show system Information 11 15 Setup 2 11 16 Quick Erase System Info To erase data on the DVD rewriteable discs quickly 11 16 Setup Quick Erase 2 11 17 Full Erase To erase data on the DVD rewriteable discs completely Compared with Quick Erase Full Erase takes longer time to do the job 11 17 Setup Full Erase 18 2 11 18 Auto Close Tray All tray will be closed in selected
4. Image P A Load 2 9 2 Delete Image If you want to delete an image file stored in a particular partition you can use this function to delete image 9 02 Image P A Delete Image Press ENT the system will confirm with you for the action use A Y to select Yes or No then press ENT for confirmation Delete Image Yes A AUDIO 537MB 2 9 3 Image Info To check selected image information First enter into the function and press W for more information 9 03 Image P A 2 9 4 Compare Image Image Info This function is used to check if created image is identical to source disc 9 04 Image P A Compare Image When result shows on LCD press ENT for more detail information Compare result OK Source and target disc are identical Fail TOC not match compare skipped due to contains not match Diff shows how many bytes are different Compare OK 1 2 9 5 Select Image This function is to select a partition as source image from the hard disk 9 05 Image P A Select Image Pressing A Y to select a partition LCD will show image name and capacity Select Partition A DATA 2 9 6 Image Src Drive This function is used to set the image source drive for loading disc data into a particular partition 9 06 Image P A Image Src Drive Enter into the function and use A Y to select image source drive Select Img Src 0
5. are 2 formats for choice Auto and Manual Auto means system auto assign partition for loaded image Manual let you to choose which partition to load image to 9 10 Image P A LoadImage Method The default is Auto Press ENT and use A Y to confirm Auto or Manual Then press ENT to save the configuration 2 10 Edit Track for CD only Function 10 Edit Track is exclusively designed for editing a collection of favorite songs from CDs In other words you can collect songs on a number of CDs and merge them into a single CD There are 3 sub functions CD to CD CD to HDD and Close Session Refer to page 11 for the menu 13 2 10 1 CD to CD Edit 10 Edit Track To select songs from source CD and then burn 10 01 Edit Track CD to CD Edit Enter into 10 01 function 1 10 means the number one of the 10 tracks and 03 55 means the length of track Select Track 1 10 03 55 You can press Y to see the rest of tracks If you want to select the track press ENT then a will shows up press ENT again will cancel the selection Select Track End 5Trk15 55 After selection use A Y move to the End which is between 1st track and last track Press ENT to end of selection and use A Y to confirm Yes or No Press ENT after burning system will ask if you want to continue edit use A V to confirm Yes or No If you want to continue edit the current source CD will be ejected and ask y
6. ihre kostenfreien Recyclesysteme konform der WEEE vor dem 13 August 2005 eingerichtet Entsprechend der Richtlinie ist SySTOR verantwortlich f r die umweltgerechte Entsorgung aller nach Deutschland exportierten SySTOR Produkte Sie k nnen Ihr zu entsorgendes SySTOR Produkt zu Ihrer rtlichen Sammelstelle bringen AEEA verklaring Met het doel de stijgende hoeveelheid afgedankte elektrische en elektronische apparatuur te beheersen zonder hiervoor onnodig stortplaatsen en verbrandingsovens te belasten en om de vervuiling van het milieu door vrijkomende stoffen uit de afgedankte apparatuur te voorkomen heeft de Europese Unie EU de richtlijn betreffende afgedankte elektrische en elektronische apparatuur besloten Deze richtlijn verplicht fabrikanten afgedankte elektrische en elektronische apparatuur in te zamelen te recyclen en te verwijderen De lidstaten van de EU hebben reeds de kosteloze recyclesystemen volgens de AEFA v r de 13 augustus 2005 ingericht Conform de richtlijn is SySTOR verantwoordelijk voor de verwijdering van alle naar Nederland ge xporteerde SySTOR producten U kunt uw afgedankt SySTOR product naar uw locale inzamelplaats brengen Elektrik ve Elektronik Madde Atiklari Demeci Elektrik ve electronik madde at klar n n yukselmesiyle basedebilmek a zt doldurma ve cop yakma Dom kullan m n azaltmak atik madde zararlar n n cevreye yay lmas n onlemek icin Avrupa Birligi AB ureticilerden elektrik ve elektronik madde a
7. 1 CHOI S MULTI 2 9 7 Image Format Info This function shows which format is used for current hard disk There are 5 formats for choice F_S CD DVD DL Double Layer and auto 9 07 Image P A ImageFormat Info Press ENT to see the following figure This figure shows that the hard disk has been formatted as F_S ImageFormat Info F S 12 2 9 8 Edit This function is to edit selected image s title subl title and sub title Only valid when the current partition contains an image file can title 9 08 Image P A Edit A title should be composed of 1 to 13 characters The character can be alphabet number or the combination of both Use A Y to select the number or alphabet After selecting a desired one press ENT for next character the end of key in press and hold ENT for 2 sec and release for next title 2 9 9 Format HDD Hard disk must be formatted by the system for the very first time Hard disk will be partitioned into the chosen partition format 9 09 Image P A Format HDD If no hard disk is installed LCD will show the message as No Valid HDD The default is F_S All data on the hard drive will be erased after the hard disk format After the hard drive is formatted correctly LCD will show Format HDD ok Press ENT to verify HDD or press V and choose No return back to menu 2 9 10 LoadImage Method This function is to change the way to save Image There
8. Press Y to select Off 20 Chapter 3 Troubleshooting 3 1 About LCD After you power up if there is no display on the LCD check if the connection of power cord is firm and the environment of power outlet is normal 3 2 About Error Messages During Copy Test Compare and Verify etc if you press ESC to abort an error message will appear on LCD Abortion may cause the copy controller to hang up therefore you have to power on again If reading fails an error message will appear on LCD Get a new source DVD to try again If the copy controller hasn t detected any device after powering on an error message will appear on LCD 3 3 About DVD ROM DVD Writers If a DVD ROM or a DVD writer cannot read confirm the format of the source DVD and check if it is damaged Use any DVD writer to read the source DVD If it works the DVD ROM is probably defective or not compatible with the source DVD 3 4 About Buttons If you press any one of the four buttons on the panel but there is no response it is perhaps that the button cannot function well Inspect the jumper setting 3 5 About DVD Writer Not Readable After copying if the DVD writer is not readable use Compare to examine or get another DVD ROM to test 3 6 About High Failure Rate If the failure rate of data copying is pretty high please following the following procedures to improve it 1 Lower the speed of DVD writer 2 Inspect if the blank disc s quality is good 3 Update the firmw
9. WEEE Statement Afin de g rer la quantit croissante de d chets lectriques et lectroniques de r duire l utilisation des d charges et des incin rateurs et d viter que des d chets nocifs ne polluent l environnement l Union Europ enne a publi la directive WEEE sur les d chets lectriques et lectroniques Celle ci sp cifie que les fabricants doivent collecter recycler et traiter l quipement lectronique et lectrique usag Depuis le 13 ao t 2005 les pays membres ont mis en place un syst me de recyclage gratuit selon le WEEE De ce fait SySTOR est responsable du recyclage de tous les produits export s vers l Allemagne Vous pouvez mettre au rebut votre quipement SYSTOR usag dans votre centre local de recyclage Pour plus d informations sur les lieux de mise au rebut des quipements usag s destin s au recyclage veuillez contacter votre mairie votre service de traitement des d chets m nagers ou le magasin o vous avez achet le produit da Con la finalidad de reducir el incremento de residuos el ctricos y de material electr nico reduciendo el uso de los vertederos e incineradoras y prevenir el preocupante aumento del contacto de estos residuos con el medio ambiente Por este motivo la Uni n Europea ha fijado la Directiva de Residuos de Aparatos El ctricos y Electr nicos RAEE solicitando a los fabricantes la recolecci n reciclaje y tratamiento de ests residuos correctamente Los paises mi
10. a a rear 2 9 7 ImageBormat iInfo sissi eee Ia at laine 2 9 9 Format IR EE 2 9 1 0 Loadimase Method a iaia Nati ati 2 10 Edit Track for CD 0nY i filiali dida ipa o 2 MOC CVI to CD le IE RR 2 102 CD to HDD Edit orcs sce us cuenta Ai DV Close SESSIONS cis Cans xa ses eats a wien dee in by ten RE sr tintin DAV SetuP AA a a ii tate abet Gat aa DE DRETT D PARA DEE e ee ee dh bia ee ee ES DAR WEE 211 4 Auto E ZALMAN eta te seca ia 2 dO Auto Verity ri Leelee nol iaia Bil lua dan en Gh Mune Re nain E ZAM ALAMOS OM PALE os tn inner crowd LR einen A ERA en une at 21158 AUTO PESCA AE brane oie ARS RIE Ra aa tt ZVI Eject DISC A Ad An i ent A dent Naa SD RIEGERT SNE ERR Buin Mod gt s iui i a alia M RE eu 2 1112 gt DiSplay Timo a Rin DALIA OU Mean oil Si ee re A A ete 2 11 14 D vice Info Lil A E deed bh a ren le ale nana DALLAS SY IL E E AO ct ate aba need 2 11 16 Quick ERAS rel Luo lalla E A LA 211 17 Fall DEE PAA A A ae INA Ia ala li ana dra AAA A iii eri a DALI Tray eee avea 211 21 BootTime Delay it nn aloe este rene Ronan sal E GE NEE SE HE EE EE 2 11 24 Show Burmn iSpeeda ceti ine anale roi Ma eee Leet Chapter 3Troubleshootng ioi ssa A Rao E aE aE ai a MAME earn 3 2 About Error Messages einer ai Whe dent a tg LE nina te nee ded oi 3 3 About DVD ROM DVD Writers Le 21 3 4 About Buttons 3 5 About DVD Writer Not Readable siens 3 6 About Hig
11. annot be obtained Press ESC for a second to terminate the test The comparison results are the same Initialize the memory of the system DO you want to load the default settings No Erasable DiscmDNDRWIL The disc on the DVD RW device is not rewritable PRE Parlin steel nn A A ste in totes The system is preparing to record Press a Key to Eject Fail Disc Press any key to eject the failed disc after copying Press a Key to Eject Good Disc Press any ket to eject the good disc after copying R ACTEUR SE et e net ct Save new config Fall Source Disc Empty eli aul Source Disc Not Ready Source Drive Not Ready s conii alia Src amp T gt can t in the same channel Target Disc Not Empty Target Disc Not ReadY so ella nolan Target Drive Not Ready Target Overflow L co concnnncnnno TOCCA aliena USA DONS neo ARA During comparison the disc cannot be read The new setting of configuration cannot be saved The source disc doesn t contain any data Source disc is not ready to be read SOurce drive is not ready to read During comparison the source and target discs cannot be in the same channel The target disc still has data Target disc is not ready to be written into Target drive is not ready to write The target disc hasn t enough capacity to store new data The comparis
12. are 4 Inspect the DVD writer s maximum writing speed If the speed is over 8X copy the data to a hard disk first and then transmit to DVD 3 7 About Firmware Update If you cannot update the firmware please inspect the firmware Perhaps you have downloaded a wrong file Failure in firmware update may cause the copy controller to fail in booting Under the circumstances return the control board to distributor for repair 21 Appendix A LCD Messages 1 Normal Conditions All data will be lost ease All data on the disc will be lost Confirm the erasing of data ANA ZII a Ni ae inde cas Audio Disc Can t comparel ccc ccc ee ence ee eee eee eeneeaeeaeees Camorra dis Check Target Please Wat Detect Drives DVD RW does not Support the Func ESE hair Failto get AAPP e Bee Fail to get Sre Disc IO AAA Hold e e en de anys A OA EA Ee Initialize SDRAM billo aaa Load Default Config LS none teintes anne eu ire DVD RW doesn t support this function Erase Finished ses 3 0 A oa Analyze the source disc The system cannot compare the audio discs wee The system cannot read the contents of disc un The system is checking the target device Detect what drives are connected with the system The erasing of data comes to an end lt The system is erasing the data on the disc The drive information cannot be obtained wee The information of source disc c
13. ated firmware has errors Data cannot be written into Flash ROM The disc doesn t contain a valid firmware The firmware is updated successfully The system is searching for a valid firmware WR RO RTE SVI During comparison the source cannot be hard disk 24
14. d the selection and the default is 16X 2 11 3 Read Speed To change default reading speed of source disc 11 03 Setup Read Speed The default is maximum the speed would depend on the reader drive s read speed and media type and format 2 11 4 Auto Start Drive System will auto start to copy or test once blank disc is ready The default is Off Press W to select 1 or 2 bla 11 04 Setup Auto Start Drive 2 11 5 Startup Menu To select any function from 1 to 13 as the first item appears on the screen whenever system is turned on 11 05 Setup Startup Menu The default is 1 Copy and 15 Adv Setup is not valid for this setting 2 11 6 Auto Verify To set if auto verify target disc s readability after copy function 11 06 Setup Auto Verify Press ENT The default is Off Press Y to select On 16 2 11 7 Auto Compare To set if auto do comparison after copy function to check if source and target disc are identical 11 07 Setup Auto Compare The default is Off Press W to select On 2 11 8 Auto Prescan To set if auto scan source disc before copy function 11 08 Setup Auto Prescan The default is Off Press W to select On 2 11 9 Eject Disc There are 3 kinds of tray behavior when copy process is completed Eject Good Only Only good disc will be ejected after burning Eject All Disc All discs will be ejected after burning Do Not
15. embros ya han establecido su sistema de reciclaje gratuito de RAEE antes del 13 de Agosto del 2005 Por este motivo SySTOR es el responsable del reciclaje de todos los productos exportados a Alemania Usted puede devolver su producto SySTOR a un punto de recogida local cuando desee reciclarlo Dichiarazione WEEE Per far fronte all aumento dei residui delle apparecchiature elettriche ed elettroniche ridurre l uso di materiale di riporto e degli inceneritori ed impedire che il materiale nocivo delle apparecchiature residue entri a contatto con l ambiente l Unione Europea UE ha stabilito le Direttive sui Residui delle apparecchiature Elettriche ed Elettroniche WEEE chiedendo ai fornitori di raccogliere correttamente riciclare e trattare le apparecchiature elettriche ed elettroniche residue Le nazioni facenti parte dell Unione Europea hanno gi stabilito il loro sistema gratuito di riciclaggio di questo materiale WEEE prima del 13 agosto 2005 Di conseguenza SySTOR responsabile del riciclaggio di tutti i prodotti esportati in Germania Potete restituire il vostro prodotto acquistato da SySTOR che deve essere riciclato da un azienda specifica locale Chapter 1 Basic Instructions There are four buttons and a LCD on the panel of SATA Copy Standard Version 1 Itshowsa function or a message It s used to scroll up function menus It s used to scroll down function menus It s used to execute a function i Mer oh ae I
16. h Falure Rate lite 3 7 Abo ut Firmw re Update dit Appendix A LCD Messages ciones israel ls acia aorta 17 18 18 18 18 18 18 19 19 19 19 19 20 20 21 21 21 21 21 21 21 22 ED WEEE Statement H x WEEE Statement English In order to cope with the increasing waste electrical and electronic equipment reduce the use of landfill and incinerator and prevent the harmful matter of waste equipment from entering the environment the European Union EU has set the Directive on Waste Electrical and Electronic Equipment WEEE asking manufacturers to collect recycle and treat waste electrical and electronic equipment properly Member nations already established their free of charge recycle systems of WEEE before August 13 2005 Accordingly SySTOR has to be responsible for recycling all products exported to Germany You can return your SySTOR product that needs recycling to a local collector WEEE Erkl rung Mit dem Ziel die steigende Menge elektrischer und elektronischer Altger te zu bew ltigen ohne hierzu unn tig Miilldeponien und Verbrennungsanlagen zu belasten und um die Verschmutzung der Umwelt durch freiwerdende Stoffe aus den Altger ten zu vermeSATAn hat die Europ ische Union EU die Richtlinie ber Elektro und Elektronik Altger te erlassen Die Richtlinie verpflichtet Hersteller elektrische und elektronische Altger te umweltgerecht einzusammeln zu recyceln und zu entsorgen Die Mitgliedsstaaten der EU haben bereits
17. lly loaded from DVD to the hard disk LR tarde The image is successfully loaded from DVD to the hard disk No Image in Partition xx No Valid ADD riali Partition Damage minap nee iaia net e re tn Godi There is no data image in partition xx The system cannot find a hard disk The partition is damaged Select a formatted hard disk at first SMI ran Do you want to verify the hard disk or just a partition Verify Hard Disk Falll apcne nici Enia iaia The hard disk is not verified successfully Do you want to directly copy the data into disc or move them to the partition The hard disk cannot be edited as a source audio disc Confirm the closing of disc sessions Ask if you want to continue the music disc editing Finish the music disc editing and start to copy Abort the selected tracks and delete them ol hie Ania Se Ne eee Do you want to insert a blank disc and continue copying Insert the next audio disc The source disc has no audio track The disc sessions have already been closed Jia The disc capacity is not enough to store the selected tracks Please select again SSC The disc capacity is not enough to store the selected tracks So do you 23 4 Firmware Update Check Sui EE EE Flash ROM fail ove le nee en ee ie E Invalid firmware ei sie MR LALA ae tente Last update F W Fait De firmware is not updated successfully L st pdate FW OR No a a ii Searching A eseman I ia ae uu The udp
18. on must be closed to max playback compatibility However no more tracks can be added once session is closed 10 03 Edit Track Close Session 2 11 Setup To change the default setting However it is suggested to use the default for the optimal operation There are 24 sub functions Language Burn Speed Read Speed Auto Start Drive Startup Menu Auto Verify Auto Compare Auto Prescan Eject Disc Burn On The Fly Burn Mode Display Time Button Sound Device Info System Info Quick Erase Full Erase Auto Close Tray Quick Compare Tray In Out BootTime Delay Start Tray Eject Disc Redetect and Show Burn Speed Refer to page 10 for the menu 11 Setup 2 11 1 Language Now press ENT and you will enter the following figure The function Language lets you select a language in which messages can be shown on LCD 11 01 Setup Language Press ENT The default is English Spanish Japanese Traditional Chinese and Simplified Chinese are made to order 15 2 11 2 Burn Speed Now press ESC and Y to enter the following figure This function lets you control the burning speed of CD writers 11 02 Setup Burn Speed Press ENT The DVD Burn Speed will be shown and the default is 8X Press W for change the selection The next one is BD Burn Speed and the default setting is 2X then Press W to change the selection to CD Burn speed and the default setting is 32X Press W for change to Audio Burn Spee
19. on results are not the same Cancel the job during operation 22 2 Connecting with a HDD All data will be lost format Image Exists Overwrite Image load Rat ee cri Image load OK aa Select HD First 3 Audio Editing Burn or Move to partition Can tedit HEES socrate ok Moksha Ses nr EE Close all dise s session cupi E oa Lala ai Continue edit next DIsc c cence cence eee cece een saseeseenses End edit disc and burn eeesseseseeeseeensees Erase selected Tracks cicala paco Viani Insert next disc NO AUDIO track in this disc Sessions were closed ee UE aon ee Target Overflow Re Select want to Tee the last track SITA All data on the hard disk will be lost Confirm the formatting of hard disk SERRE LL Confirm the deleting of data image in partition xx Format HDD ran OI do ii Format HDD OKR lessee ieri HDD not For ui rieti HDD too small dirias HDD too small to handle image Ask if you want to format the hard disk The Formatting of hard disk has been completed The hard disk hasn t been formatted yet The capacity of hard disk is too small The hard disk hasn t venni capacity to store the data image at least SGbytes CREA There is a data image in the current partition Confirm the overwriting of data A ETRE A The image isn t successfu
20. ou to insert next disc Repeat the above process for editing Insert next disc After editing system will show Close all disc s session Yes use A Y to confirm Yes or No Once session is closed no more tracks can be added Close all disc s Session Yes Attention Commercial audio player might not able to play open session disc close session is suggested for max compatibility 2 10 2 CD to HDD Edit To select tracks from single or multi audio CD and create image to specific partition of HDD 10 02 Edit Track CD to HDD Edit The basic operation method is same as CD to CD Edit system still ask you to insert empty disc even the target drive is 14 HDD If burning successful system will show Image load OK which means the selected tracks are written to temporary partition Press ENT after burning system will ask if you want to continue edit use A Y to confirm Yes or No If you want to continue edit the current source CD will be ejected and ask you to insert next disc Repeat the above process for editing If No is selected system will show Burn or Move to partition use A Y to confirm Burn or Move Burn Burn the selected tracks to CD Move to partition Create an image for selected tracks Moving to P B 2 10 3 Close Session Single session format is used for Audio CD and commercial audio player is not able to play open session audio CD therefor sessi
21. start simulation and copy Note only passed test disc will do the copy 2 4 Verify Function 4 check readability of the burned disc 4 Verify 2 5 Compare Function 5 to check if target disc is identical to source disc 5 Compare Compare result OK Source and target disc are identical Fail TOC not match compare skipped due to contains do not match Diff shows how many bytes are different 2 6 Prescan Function 6 to check if source disc is readable and without read error 6 Prescan 2 7 Disc Info Function 7 to report disc information disc type and capacity 7 Disc Info 2 8 Select Source Function 8 to set which drive as source device 8 Select Source The drive on CHO1 will be chosen as source device Press ENT and then press A Y to select the source Assume that HDD is selected as the source device and selected partition contains no data an error message Source Drive Not Ready will show on LCD while trying copy function In that case go to Function 9 Image to load the data into the chosen partition first 10 2 9 Image Function 9 Image is valid only when a hard disk is installed Disc is loaded to hard disk as an image file Refer to page 11 for the menu 9 Image 2 9 1 Load Load function loads whole disc data from any writers into the current partition of the hard disk P A means current partition is A 9 01
22. t klar n gerektigi gibi toplamalar n geri donusturmelerini ve kimyasal isleme tabi tutmalar n talep etmek icin Elektrik ve Elektronik Madde At klar uzerine bir direktif haz rlad Topluluk uyeleri 13 Agustos 2005 ten once elektrik ve elektronik madde at klar n n ucretsiz geri donusum sistemlerini coktan olusturmuslard Bundan dolay SySTOR Almanya ya ihrac ettigi butun urunlerin geri donusumunden sorumludur SySTOR urunleri geri donusum gerektirirse yerel toplayicilara geri verebilirsiniz WEEE OroJiereHb Russian UTOGDI cllpaBATbCA C YBOJIMIMBAFONIMMCA HEHYKHBIM SJIEKTPHACCKAM H SJIEKTPOHHBIM OGOPYAOBAHAEM yMeHbIINTE HCHOJNB30BAHHE 3AKAlBIBAHHMA MYCOPA H HCIOJIb30BAHHA YCTAHOBKH JIA CKHTAHHA OTXOXI0B HPETATCTBY TE BPEAHOMY BBIOpocaM 3arpa3HATb OKPYKAHOBKH Cpexy EBpone ckn c0103 EC ycranoBux Aupexrusy no HeHyxHomy INEKTpMIECKOMy H INEKTpOHHOMy O6opy1oBamuto WEEE ag Toro UTOOBI H3rOTOBHTENEH COOpaxn repepa0aTbIBAJIM H BOOOUIE HPOIBAIH BHAMAHHE K HCHYKHOMY SJIEKTPHAIECKOMY H 3JISKTPpOHHOMy OGOPYAOBAHAIO AOJDKHBIM 06pa30M YJICHbI HAHH yCTaHOBHJIM CCIJIATHYIO CHCTEMY H ANEKTPOHHOMy OGOPYAOBAHAIO JOJDKHBIM 06pazom UIeHbl HAHH ycraHOBHJIIM GeCHIATHYIO CHCTEMY nepepavorka WEEE ao 13 agrycra 2005 CoorBercTBeHHO SySTOR 06013aH bIT5 OTBETCTBEHHBIM 34 TO UTO HepepaGoTAN BCE MPOAYKTBL IKCIOPTHPyeMBIE B TepmaHnro Bur MOXETE BO3BpaTHTb Ban HPOAYKT SySTOR KOTOPHI HYKAACTCH B peLMPKyJIALMM MECTHOMy COOpUIMKy
23. t s used to cancel a function Chapter 2 Functions There are 11 major functions in the copy controller as the following figure shows and there are sub functions in Function 7 9 10 and 11 as the following figures show Copy Test Test amp Copy Verify Compare Prescan Disc Info Select Source Duplicator Controller ES Image 10 Edit Track 11 Setup In Function 7 there are 2 subfunctions 7 1 Source 7 Disc Info A 7 2 Target In Function 9 there are 7 subfunctions 9 1 Load 9 2 Delete Image 9 3 Image Info 9 Image 9 4 Compare Image 9 5 Select Image 9 6 Image Src Drvie 9 7 Image Format Info In Function 10 there are 3 subfunctions 10 Edit Track 10 1 CD to CD Edit In Function 11 there are 24 subfunctions 11 Setup 10 2 CD to HDD Edit 10 3 Close Session 11 1 Language 11 2 Burn Speed 11 3 Read Speed 11 4 Auto Start Drive 11 5 Startup Menu 11 6 Auto Verify 11 7 Auto Compare 11 8 Auto Prescan 11 9 Eject Disc 11 10 Burn On The Fly 11 11 Burn Mode 11 12 Display Time 11 13 Button Sound 11 14 Device Info 11 15 System Info
24. time and if disc is ready system will auto start copy test or both functions depends on which function is stay on the LCD screen 11 18 Setup Auto Close Tray 2 11 19 Quick Compare Quick Compare is related to function 5 Compare Once compare error byte reach to the setting figures compare process will stop 11 19 Setup Quick Compare The default is Off press Y to select 1 Byte 1 KB 10 KB 100KB 1 MB 10MB 100MB etc 2 11 20 Tray In Out Lets you control the drive tray ejecting 11 20 Setup Tray In Out Press ENT The default is AIl Once and there have Divide 2 Times for selection 2 11 21 BootTime Delay To set the device scanning time during the system booting 11 21 Setup BootTime Delay The default is 5 second more option is up to 99 seconds 2 11 22 Start Tray Eject To set if do eject all tray after system boot up 11 22 Setup Start Tray Eject The default is On Press W to select Off 19 2 11 23 Disc Redetect The function is designed specially for bad quality disc the system will detect the disc one more time if disc recognition error occurred 11 23 Setup Disc Redetect The default is Off Press W to select On 2 11 24 Show Burn Speed Now press ESC and Y to enter the following figure This function lets LCD shows the burning speed of CD DVD BD writers 11 24 Setup Show Burn Speed The default is On
Download Pdf Manuals
Related Search