Factory Direct Medical
Contents
1. If the tires are worn replace them immediately Warning Do not attempt to repair or service the scooter or any of its components as this will void your warranty SERVICE AND REPAIR CONTACT YOUR AUTHORIZED DEALER Rover 3 and 4 22 User Manual E Rev Feb 2012 Troubleshooting Scooter drives slowly and Batteries are low Recharge the batteries indicator light flashes slowly The wheels pull to one Check the tire s air pressure direction Noises come from the motor Make sure no foreign objects or dirt is and or the wheels stuck in the wheels or wheel hubs If you do not find any obstructions contact the service center The scooter does not turn on Check that the key is inserted properly Make sure that the batteries are inserted in the right position Check the battery charge Batteries do not charge Check the connection between the charger and the scooter charge outlet Make sure that the batteries are inserted in the right position Make sure the charge indicator light is lit during charging The scooter turns on but Make sure the wheel release handle is does not drive in drive position See Fig 3 Verify that there are no objects interfering with the scooter Check the battery charge status Rover 3 and 4 23 User Manual E Rev Feb 2012 If the scooter does not operate properly and the indicator light is flashing quickly count the number of flashes in each sequence in order to define the prob2. it is stabilized in a fixed position 5 Raise the tiller handle slightly in order to release the tiller lock Then fold the tiller towards the seat see Fig 13 Figure 13 6 Lift the front chassis using the handle located under the seat Disconnect the front chassis from the rear chassis see Fig 14 Figure 14 Rover 3 and 4 12 User Manual E Rev Feb 2012 Adjustments for Seating Comfort Your power scooter allows you adjust the tiller and the arm rests to maximize seating comfort and configure the scooter to your body structure 1 Tiller Angle Adjustment A Pull the tiller lever up see Fig 15 Alternatively the tiller lever may be pushed from the back of the tiller B Move the tiller to the desired position and release to lock Tiller Handle for Adjusting Tiller Angle Figure 15 2 Arm Rests When getting on or off the scooter you can raise the arm rest for easier access and motion see Fig 16 Figure 16 Rover 3 and 4 13 User Manual E Rev Feb 2012 Operating the Scooter Operating the scooter is not complicated However we recommend reading these instructions prior to using the scooter to ensure full understanding of the scooter operations Note Be aware of the environment around you when choosing a desired speed For indoor environments we recommend that you select the slowest speed setting For outdoor operation select a speed that is comfortable for you to control
3. safely Control Panel The control panel is located in the center of the tiller It enables you to control the steering lights and signals of the scooter supplies information on the battery status and shows fault warnings see Fig 17 T Figure 17 Rover 3 and 4 14 User Manual E Rev Feb 2012 The following table details the various systems on the control panel 1 Operating Key Main On Off switch power source for the Titan Remove the key when the scooter is not in use 2 Operating Lever Moving the lever controls the speed To Left Right drive forward pull the right lever toward you and push the left lever away from you Releasing the lever will bring the scooter to a gradually stop To drive backward pull the left lever towards you 4 Manual Speed The maximum speed is 11 km h Rotating Adjuster the button to the lower speed turtle icon will reduce the speed for slower gentle operation 5 Turn Signal Operates the turning signal lamps 6 Hazard Lights Signal Operates the emergency warning lights 7 Speed Selector Switch Set the switch to the lower speed turtle icon position for slower operation 8 Battery Charge Indicator Shows the state of the battery whenever the scooter is operation 9 Operation Indicator Shows operational faults See Table of Faults 10 Lights Switch Turns the front and rear headlights on and Hand Grips Flexible hand grips for comfortable hand support
4. the Rover 3 and 4 is twelve months and covers faulty materials and workmanship consumables not covered tyres upholstery lamp bulbs plastic coverings and batteries Worn parts damaged as a result of excessive loading improper handling intentional damage or unauthorized maintenance or modification are not covered by the warranty For safety and for warranty assurance reasons any modifications and repair of the Rover 3 and 4 or its components must be performed exclusively by authorized personnel and exclusively with original spare parts Manufactured by ractoryDirectMedical 220 Wildcat Rd Toronto Ontario M3J 2N5 Tel 416 7398393 Fax 416 739 7171 Internet Mail info factorydirectmedical com Internet Address www factorydirectmedical com Rover 3 and 4 26 User Manual E Rev Feb 2012
5. 12 Tiller Handle Adjusts the tiller to your preferred position Rover 3 and 4 15 User Manual E Rev Feb 2012 Suggestions for Safe Driving E Before operation make sure the front and rear chassis are connected and locked m For your own safety and the safety of others always drive at a moderate speedy m Releasing the operating handle will bring the scooter to a stop E Operate with caution whenever going up or down a ramp or slope m When entering an elevator drive in reverse so that you can then exit facing forward Check that the elevator has stopped at the exact level of the floor Rover 3 and 4 16 User Manual E Rev Feb 2012 Batteries and Charger Batteries The Rover scooter is programmed to work with sealed maintenance free 12V batteries Note Turn off the scooter before removing or installing batteries Full charging of the batteries prior to usage helps keep them operational and lengthens their lifespan Batteries can be charged at any time without concern for over charging Note Do not use a car battery Car batteries are not designed for the scooters and can be dangerous Battery lifespan is influenced by treatment number of recharges storage and usage Charging the Battery The charger works with a standard socket outlet between 100 240V The charger automatically prevents over charging Note The battery cannot be charged if it completely discharged It is recommended that you r
6. e Seat Foldable armrests Basket and support tube Battery packs detachable Rear Wheels Figure 3 Anti tip Wheels Battery Charger a eee ST SS eS eS PS a ee Rover 3 and 4 4 User Manual E Rev Feb 2012 Safety Instructions Operation These safety considerations and tips will help you operate the scooter safely The Scooter is a powerful electric vehicle and the following rules will help you prevent personal injury and damage to your scooter m Make sure that your weight does not exceed the recommended weight limit of the scooter see Technical Specifications Do not carry passengers m Always ensure that the power is switched off when getting on or off of the scooter When getting on and off the scooter do not step on the foot rest m Atall times while driving keep your feet on the foot rest Be aware of the environment around you when choosing a desired speed For indoor environments we recommend that you select the slowest speed setting For outdoor operation select a speed that is comfortable for you to control it safely m Reduce speed when making sharp turns Do not switch off the power when the scooter is still moving forward This will bring the scooter to an extremely abrupt stop m Avoid jerky stop start motions as it will result in excessive battery drain and increased tire wear To break in an emergency simply release the forward reverse lever m Make sure the wheel release lever is in drivi
7. echarge as often as possible The batteries can only be charged while they are connected to the scooter Plug the charger connector into the scooter input outlet and then connect the charger to the power source see Fig 18 Rover 3 and 4 17 User Manual E Rev Feb 2012 Indicating Light Charging Charged a Figure 18 While charging the charging indicator light will be lit red When the batteries are fully charged the indicator light will change to green For maximum battery utilization charge the battery overnight or for at least 4 hours after the light turns green Safety Instructions Follow these instructions to prevent damage or harm during charging m Make sure the scooter is turned off and the key removed before charging m Use the charger only for charging the scooter batteries Charge the batteries in a well ventilated area Do not smoke near the batteries and keep away from source of heat or flames Charge the batteries indoors or in a covered area and avoid water Always dry hands before charging Remove jewelry before charging Do not use charge cables that are damaged in any way It is recommended that you change both batteries if they are weak If you do not use the scooter for an extended period be sure to charge the batteries at least once a month m Charge batteries overnight There is no need for concern of over charging Rover 3 and 4 18 User Manual E Rev Feb 2012 Battery St
8. ery replacement should only be performed by an authorized agent Note The batteries may emit a minimal amount of acid fumes When removing batteries always place them on cardboard newspaper or any other material that will prevent damage to the surface on which they stand Rover 3 and 4 20 User Manual E Rev Feb 2012 Maintenance and Repairs Your scooter requires only minimal maintenance Like any motorized vehicle there are some maintenance operations that are required m Avoid driving the scooter in the rain Keep the scooter covered and stored in a shaded and dry place away from damp or wet areas Keep the batteries away from sun and rain m Keep the scooter clean Clean the seat using a moist cloth You can use a mild carpet cleaner Painted areas can be further protected using car wax Do not get the electrical cables or connectors wet To ensure a long and trouble free operating life we recommend the following regular maintenance operations Daily Checks m Visually inspect the vehicle and the wheel condition m Watch the battery status m Make sure the operation lever returns to neutral position after release Weekly Checks m Operation lever check pull the lever to maximum speed Turn the key to the on position The scooter should not move and the indicator light should flash If the scooter moves at all contact your service center m Braking check perform this check on a flat area away from any obstructio
9. he basket support frame into the two tubes located on either side of the rear tray Make sure the frame is secure and stable 2 Insert the basket into the basket support frame Make sure it is seated securely see Fig 9 Folding Tiller Handl A Pelis gt gt Rear Basket Y gt Basket Support Frame Folded Seat Figure 9 Moving the Scooter When moving the scooter without operating it be sure to follow these instructions 1 Turn the power off 2 Ensure that the wheel release lever is in Freewheel mode see Fig 4 3 Move the scooter carefully and slowly 4 To brake the scooter move the wheel release lever to the Drive position Note Do not change the scooter to freewheel mode when on a slope Disassembly Rover 3 and 4 10 User Manual E Rev Feb 2012 If necessary the scooter can be easily disassembled To transfer the scooter safely follow these steps 1 Turn the power off 2 Fold the backrest down slightly raise the seat and push it forward and down see Fig 10 Figure 10 3 Remove the rear basket and the basket support frame see Fig 11 Folding Tiller andle A a Rover ae ar Figure 11 4 Disconnect and remove the batteries from the rear tray see Fig 12 Note Pull the battery up first to disconnect from electrical contacts Rover 3 and 4 11 User Manual E Rev Feb 2012 Figure 12 Note To avoid damage when disassembling the scooter make sure
10. lem in accordance with the table below Either the battery needs charging or the batteries There is no connection to the motor Check the There is a short circuit between the motor and the 7 Problem with the operation lever Make sure it is set in the middle before operating the scooter Problem with the controller Make sure all the connections into the control panel are tight and secure There is no connection between the controller and the brake Make sure all connections to the brake and controller are tight and secure Controller overload Likely a result of a failure in the battery connection Check connections to the battery and controller Rover 3 and 4 24 User Manual E Rev Feb 2012 Technical Specifications Power supply 24V from 2 charged sealed lead acid maintenance free 12V 26Ah batteries Estimated range 25 km 15 5 miles using recommended battery and depending on operating conditions and load Scooter weight 64 kg 141 Ibs 72 kg 158 7 lbs including battery Front chassis weight 22 kg 48 5 Ibs 27 kg 59 5 Ibs Rear chassis weight 23 kg 50 7 Ibs 26 kg 57 3 Ibs ie Front Wheels 31x5 5 cm 26x8 cm Rear Wheels 31x5 5 cm 34x6 5 cm Wheel air pressure 35 psi 2 5 bar 45 psi 3 2 bar Dimensions 139X60X95 cm 137x62x95 cm Length Width Height 54 7x23 6x37 4 in 53 9x24 4x37 4 in Rover 3 and 4 25 User Manual E Rev Feb 2012 WARRANTY The warranty period for
11. n within 1 meter Turn on the scooter Pull the operation lever to the Forward driving position until you hear a click Release the brake The scooter should move forward slightly Release the operation lever Within a few seconds you should hear the click of the brake locking In addition repeat this check for reverse driving Rover 3 and 4 21 User Manual E Rev Feb 2012 m Air pressure check the wheel air pressure should be 2 5 bar 35 psi Keeping the air pressure at the proper level will lengthen the tire lifespan and will increase the travel distance per battery charge Semi annual Checks m Use lubrication WD40 or similar on the following areas Chassis locking pins Seat locking snib m Check the wear and tear of the wheels Annual Checks m We recommend that an authorized technician perform the annual check The technician will check functionality all connections the electric motor status and the battery condition m Fuse replacement should be done only by a service representative Fuses are located in the following locations 60A Battery pack fuses one in each battery pack 5Ax2 electrical circuit fuses under the rear cover Periodic Checks m Clean upholstery plastic and metal parts with a mild surface cleaner Caution keep cleaning solvents away from electrical wires and connectors m Keep dirt out of the wheel axes including lint hair sand and carpet fibers m Check for tire wear
12. ng mode prior to operation see Fig 4 Rover 3 and 4 5 User Manual E Rev Feb 2012 m Make sure the wheel release lever is in driving mode prior to operation see Fig 4 T l Freewheel Mode Figure 4 Mm Make sure the forward reverse lever is in the proper position according to your desired direction Ramps and Curbs Sidewalks Use extra caution when driving down a slope Never drive across a slope Do not turn sharply on a slope Do not drive in reverse on a slope or on a bumpy surface When driving over a curb or raised surface make sure that the bottom of the scooter has sufficient clearance see Technical Specifications Rover 3 and 4 6 User Manual E Rev Feb 2012 General Instructions m Do not attempt to lift or move a power scooter by any of its removable parts Personal injury and damage to the power scooter may result m Do not drive the scooter on a major roadway m Avoid driving in the dark or in times of limited vision m Do not connect any electrical or mechanical devices to the scooter Doing so may cause personal injury or damage to equipment and voids the manufacturer s warranty m Do not operate your vehicle if it is not functioning properly Contact your service center immediately Influence of Medication or Alcohol Check with your physician if you are taking any medication that may affect your ability to operate your power scooter safely m Do not operate your
13. orage Before storing make sure the battery packs are fully charged When stored bring out the batteries to charge at least once every 3 months Temperature for storage 20 C to 40 C Temperature for charging 0 C to 40 C Temperature for operation 20 C to 50 C Battery Troubleshooting The battery indicator shows the battery status and warns about problems by flashing Action escription Indicator is lit with no System is operational flashing Slow flashing indicator Charge the batteries as soon as possible Quick flashing Trouble indicator Perform the following actions indicator Turn off the scooter Make sure the rear wheels are locked Make sure the charger is disconnected from the scooter Make sure the operating lever is set in the middle If the lever does not return to center do not operate the scooter and contact your service center Turn the scooter on and begin driving If the indicator continues flashing quickly count the number of flashes in each sequence and check the specific problem in the Troubleshooting table at the end of this manual Safety Measure Rover 3 and 4 19 User Manual E Rev Feb 2012 Read the directions before charging Charge in a well ventilated area Use only the manufacturer s recommended battery type E ie R Disconnect from the power source immediately upon completing charging p Each battery pack contains sealed lead acid batteries Batt
14. t EZee Life Rover 3 and 4 Scooters User s Manual Original instructions Dear User Factory Direct Medical would like to thank you for choosing the Rover 3 and 4 scooter and wishes you safe and enjoyable journeys For proper operation and to maintain the scooter s operational readiness we recommend that you read this user manual prior to using the scooter H ractoryDirectMedical 220 Wildcat Rd Toronto Ontario M3J 2N5 Internet Mail info factorydirectmedical com Internet Address www factorydirectmedical com Rover 3 and 4 2 User Manual E Rev Feb 2012 Table of Contents COMPONENTS 25625 2ccieicce arora E 7 Safety INSITU CHONG sr irani rir 9 Assembly Instructions ccecceeceeeeeeeeeeeeeeeaneens 13 Adjustments for Seating Comfort cceeeeeeeeees 18 Operating the Scooter crror in a aE 19 Batteries and Charger ccccccceceee eee eeeeeeeeeeaeeaeans 23 Maintenance and Repairs ccceeeeeeeeeeeeeeeeeaeees 27 TFOUBIES HOUND ez ascnrnanachunedaacievenss a a 29 Technical Specifications ccc cc ece ese eceeeeeeeeeeeeees 31 Rover 3 and 4 3 User Manual E Rev Feb 2012 Components Your power scooter comes partially disassembled for protection during shipment After unpacking please familiarize yourself with the following components see Figs 1 2 and 3 Figure 1 Rover 4W Control Panel Tiller Front Wheel Foot Platform Foldabl
15. vehicle while you are under the influence of alcohol as it impairs your ability to operate your power scooter in a safe manner Rover 3 and 4 7 User Manual E Rev Feb 2012 Assembly Instructions It is very easy to assembly your scooter Please follow the steps below Contact your service center in any problems occur Chassis Installation 1 Insert both batteries into the back chassis see Fig 8 2 Using the handle located behind the seat raise the front chassis and connect it to the back chassis Make sure they are aligned and locked see Fig 5 Figure 5 Tiller Positioning 1 Pull up the tiller handle in order to release the position lock see Fig 6 2 Adjust the tiller to a driving position according to your own preference Figure 6 Rover 3 and 4 8 User Manual E Rev Feb 2012 Installing the Seat 1 Raise the seat assembly until it reaches a locked position see Fig 7 2 Raise the backrest to an upright position Figure 7 Installing the batteries 1 Take the batteries out of the box 2 Place the battery into the rear tray with the protruding part towards rear see Fig 8 3 Then lower the battery until it stops the connectors will engage Note The batteries are partially charged We recommend charging them fully prior to usage Figure 8 Rover 3 and 4 9 User Manual E Rev Feb 2012 Installing the Basket Support Frame and Rear Basket 1 Insert the legs of t
Download Pdf Manuals
Related Search