Easy RGB(W) Remote controller User Manual
Contents
1. 5 5 The usage of number button amp 5 5 1 Press on number button for choosing the corresponding receiver E g to adjust the brightness of receiver 1 you need to press 1 button Q then press MO Or IO to adjust its brightness 5 5 2 Pressing number button can turn on Off the corresponding single receiver E g If you need to turn off receiver 1 press button O more than 2 seconds if you need turn it on again please press button Q again for more than 2 seconds Notice If you turn off the extension by pressing the corresponding number button you must turn on this receiver in the same way The receiver can not be switched on through button ON OFF 6 Symptoms and solutions The Receiver 1 Exceeded learning 1 Press receiver learning cannot be learned time learning time button LED indicator is to the sender is only 5 seconds ON press the number 2 Sender is in sleep button before led indicator mode is OFF then press function button or touch color wheel Press On Off to make the sender under working status The sender 1 Receiverisn t Tolearn the receiver by cannot control learned to the the sender the receiver sender When receiver is learned 2 The receiver isn t to the sender press learned to the number button first then sender correctly press function button or 3 Remote distance 1s touch color wheel out of range Shorten the remote 4 Incorrect receiver distance2. Choose correct receiver ID Color changing 1 MASTER receiver 1 Reset a new MASTER 15 isn t isn t set receiver synchronized More than two 2 Relearn all the receivers MASTER receivers with one MASTR receiver are Set Wrong color 1 Wrong connection 1 Reconnect RGB W of RGB W electric electric wires wires LED flashing 1 the power supply is 1 Change a higher wattage not large enough power supply 7 Precautions JA 12 13 7 4 Please remove the batteries if the unit is not used for a long time Don t drop the sender from a high place or don t squash it Please replace new batteries if there is a warning indicator of insufficient power otherwise it would cause damage to the sender Receiver is non waterproof and not for outdoor use
3. Easy RGB W Remote controller User Manual 1 Product introduction Easy RGB W remote controller is a wireless color controlling system that consists of a sender and a receiver or several receivers as shown in Figure 12 By selecting switch status you can set the system as RGB 3 channel output or RGBW 4 channel output Using Easy RGB W remote controller you can get whatever color you want you can choose any color from RGB W to adjust so as to mix more than 1 million kinds of colors With built in 10 kinds of color changing modes you can easily switch color changing modes and adjust speed and brightness Function Pause enables RGBW LED to stay at your favorite color under the situation of color changing modes which operation is simple but functional Sender Fig 1 a n PIPPI OOO usi Ssnjg Mopar JAS hoi T ma T ma a 0 Receiver Fig 2 2 Performance parameters 2 1Sender Working temepature 4 5V 3x1 5V 7 AAA battery Working current lt 22mA Dormancy current lt 20uA Working frequency 434MHZ 868MHZ 915MHZ optional Transmit power gt 5dBm 2 2 Receiver Input Voltage 12 36VDC Output Voltage 12 36VDC Input Current 4CHx5A max Output power 4CHx 36 160W Working Frequency 434MHZ 868MHZ 915MHZ optional 3 components description 3 1 Sender m amp R button and indicator w C G button and indicator E B button and indicator
4. GB W remote controller must learn the ID of the receiver the purpose of learning ID code is to make a certain receiver which can correspond the sender The method of Receiver learning ID is as follows press the ID learning Se O button on the sender the ID learning indicator is on then press one of the number button O OO onthe sender press the number that you want this receiver to be E g If you want this receiver to be No 1 please press button Q first then touch the n O Or you can press any functional button on the sender such as s E ON to transmit signal to the Sender after Receiver receives the signal from the sender the indicator will flash a few times and then turns off then receiver ID is activated If the ID activation is failed at the first time please repeat the previous procedures Attention The receiver ID learned by touching color wheel z is different from the reciever that learned b ressin unction button W G m o The receiver ID learned by touching color wheel O we define it as SLAVE receiver the receiver ID learned by pressing function button W G Ok we define it as 6 MASTER receiver The purpose of learning these two kinds of receivers is to ensure the receivers and color changing synchronously to avoid the color changing out of sync between controllers This point will be noted later 4 3 Delete ID and ID re learning If you n
5. O w W button and indicator G Working status indicator the sender is in sleep mode when the indicator is off The sender is transmitting when the indicator is flashing rapidly If the indicator continues flashing at the freguency of 1 second it indicates that the sender batteries low and needs to replace new batteries Slow down the speed when color is changing Speed up when color is changing Multifunction button used for selecting Synchronous or asynchronous mode all zones change at the same time or chase Brightness down Brightness up Multifunction button used for turn ON OFF and white output O 12 Figure 1 10 is for selecting receiver s ID and ID itself to turn ON OFF Touch wheel for selecting R G B colors 4 3 2 Receiver uae 224 ollo Jl power input socket red SEC green blue 0500800008 yellow J2 RGB W output socket es Erer 3 RGB RGBW output switch closed circuit is RGB 3 channel output open circuit m is RGBW 4 channel output Receiver ID code learning Button Receiver ID code learning indicator and for receiving message 4 Basic Usage 4 1 Install battery Initial using easy RGB W remote controller open the battery cover on the back of the sender load 3pcs 7 AAA 1 5V batteries Please pay attention to the battery s negative and positive otherwise it will fail to work 4 2 Receiver learning ID Initial using easy R
6. ame time synchronized signal will be emitted so as to ensure this group receiver will be in order no matter how long the color changes and keep changing forever For example 10 receivers are learned to be ID 1 these 10 receivers will change according to one mode in order to avoid chaos of working units after a long time one of the receivers is needed to be set as Master the Master will launch synchronized signal when color is changing thus ensure this group of receivers are in good order no matter how long the color is changing 5 5 Color changes of multiple different ID receivers in the same mode In order to avoid chaotic phenomena after a long time when multiple different ID receivers are changing the color under the same mode one MASTER receiver is needed to be set in this group How to set MASTER receiver and SLAVE receiver please refer to 4 2 Receive learning ID code Notice Only one master receiver can be set among a group of receivers otherwise it may cause chaotic phenomena the Master will launch 12 synchronized signal when color is changing to ensure this group of receivers will be in good order no matter how long the color changes For example Receiver 1 2 3 4 5 move color under the same mode 1 at this time you need to set one of the receivers as Master receiver 1f receiver 1 is set as MASTER then receiver 1 will launch synchronized signal to other receivers 2 3 4 5 meantime they will keep changing constantly witho
7. eed to delete the ID learned in the receiver press ID learning button for more than 5 seconds when learning indicator is off then the learned ID is deleted If you need the receiver learn a new ID repeat the operation of 4 2 Receiver learning ID 4 4 Choose color by touching color wheel After the receiver learned the ID you can change each receiver s color by touching color wheel If you want to change the color of receiver NO 1 Press button Q then make rotating touch on color wheel your figures at this time the color of receiver No 1 will be changed constantly when your favorite color appears stop rotating and leave the color wheel O If you need change color of several receivers at the same just choose a number for these several receivers first then touch color O For example change color for receivers NO 1 2 3 4 5 6 at the same time you need press number to 6 button O O O O first then touch the color O amp N a a 4 5 Select or adjust color by R G B W button amp C O In addition to change the color by touching color a O but you can also select the single color through R G B W buttons o a a amp O or adjust the color by color wheel to get your wanted color For example you choose a color by touching color wheel O still want add a bit more brightness to red color just press R G button for over 2 seconds then the indicator
8. n press M button receiver will be changed as Mode 1 again 4 7 Brightness adjustment Under the static color status or color changing status you can adjust the brightness by press B OR pressing button gt to increase the brightness The brightness is divided into 8 levels the minimum is 10 and the maximum is 100 4 8 Changing speed adjustment Under color changing mode you can slow down the changing speed by pressing button or Speed up changing speed by pressing button 16 speed levels in total are available The maximum changing cycle is 4 seconds the minimum changing cycle is 256 seconds 5 Expanded Usage 5 1 Color changing for multiple same ID receivers under same mode One receiver of the sender can be learned unrestricted by multiple receivers a receiver can be only defined one ID No from one sender If one of senders is learned by several receivers all these receivers will share the same ID No When all these receivers are changing color at the same time to ensure long time changing in order one of the receivers from this group is needed to be set as Master receiver and other receivers need to be set as Slave receivers How to set Master receiver and Slave receiver please refer to 4 2 Receiver learning ID code Notice Only one receiver Master can be set in a group of receivers otherwise it may cause chaotic phenomena When Master receiver is set this group receivers are changing color at s
9. of R will be on and red N is selected make clockwise rotation _ on the color wheel by finger then the brightness of red will be increased If you want the red color ae ort N Pa to be darker just make counter clockwise rotation on the color i O If need to adjust the color brighter or dim several colors at same time also just choose the colors such as R G then make clockwise N N a X O i N rotation or counterclockwise rotation it can simultaneously adjust the brightness for both colors If you want to cancel the selected color just press selected button for 2 seconds the corresponding color will be off and the color is abandoned W e e By pressing of R G B W button amp Q O you can turn on off the corresponding single color For example if you want LED lightings to get red press R for over second then the red color will be turn on If you want to turn off red again press R Q for 1 second the red will be off again The same operation is for other colors Note that If you select a color output such as red then you select another color output such as green So red and green are output at the same time If you only need to separate out the second output green just turn off the front color red In short using R G B W buttons amp Q C O and operating color 1 O y
10. ou can mix more than 1 million colors or any color you want Attention The receiver is under single or multi color adjustment condition when any single or multi color is selected Under this condition you 2 oa a 7 4 N can only make clockwise rotation or counterclockwise a CS rotation operation to adjust the color A direct touch on color 1 On not work Only after exiting from the single or multi color condition a direct touch on color wheel O Work 4 6 Choose color changing mode Selecting the mode 1 O receiver change colors according to different modes a total of 10 built in color changing modes If you want one or several receivers under color changing mode press number button 2 and choose receiver number then press button ON For first press of MO receiver will change according to mode 1 one more time press of MO the receiver will be paused it will stay at one color under mode 1 condition Press MO again the color will change according to mode 2 press button ON more time it will be paused at one color under mode 2 Press san MD for seconds the receiver will keep changing as follows MODE1 STOP MODE2 STOP MODE3 STOP MODE4 STOP MODES STOP MODE6 STOP MODE7 STOP MODE8 STO P MODE9 STOP MODE10 OF F MODE1 The receiver will be at one of static colors by touching the color wheel in color changing modes The
11. ut chaos according to the synchronized signal from receiver 1 In addition if there are several receiver 1 only one of them can be set as MASTER receiver others must be set as SLAVE receiver otherwise it will cause chaos 5 3 The usage of button M the switch between Synchronous color changing and asynchronous color changing Press MO for 2 seconds to switch between Synchronous color move and Asynchronous color changing when multiple different receivers are in the same mode Synchronous color changing means the starting point and ending point are at the same time Asynchronous color changing means there 1s certain time delay of the starting point and ending point the later receiver start or ending point is always later than the previous receiver For example Receiver 1 2 3 4 5 changing together under mode 1 if it is Synchronous color changing all of the receivers change will start and end at the same time If it is Asynchronous color changing then receiver 1 will start change firstly then follows by receiver 2 and later by receiver 3 and receiver 4 and receiver 5 and recycle to receiver 1 The purpose of asynchronous color change is to achieve the color changing effect which looks like water chasing 13 5 4 Usage of ON OFF 5 4 1 Press of ON OFF button for turning ON OFF receiver 5 4 2 Press ON OFF 1 O for more than 2 seconds it can reveal white light output each channel is 100 output
Download Pdf Manuals
Related Search