ROBO-8110VG2AR User`s Manual
Contents
1. Bus Interface Follow PICMG 1 3 Rev 1 0 standard PCI Express and PCI Support four PCI Express x1 can be aggregated as one PCI Express x4 through backplane by different bios Support four PCI devices through backplane Support one PCI Express x16 or two PCI Express x8 or One PCI Express x8 Two PCI Express x4 by jumper setting SATA Four SATA 300 ports on board dual ports via backplane and two SATA 600 ports Floppy Drive Interface Support one FDD port up to two floppy drives and 5 1 4 360K 1 2MB 3 1 2 720K 1 2MB 1 44MB 2 88MB diskette format and 3 mode FDD Serial Ports Support one RS232 and one RS232 422 485 selectable ports Parallel Port Support one parallel port with SPP EPP and ECP modes USB Interface Support fourteen USB 2 0 Universal Serial Bus ports two USB ports on bracket that dedicated to keyboard amp mouse eight USB ports on board and four USB ports via backplane for high speed I O peripheral devices PS 2 Mouse and Keyboard Interface Support one 10 pin header for external PS 2 keyboard mouse connection ROBO 8110VG2AR User s Manual 1 3 System Overview Auxiliary I O Interfaces System reset switch external speaker Keyboard lock and HDD active LED etc Real Time Clock Calendar RTC Support Y2K Real Time Clock Calendar with battery backup for 7 year data retention Watchdog Timer Support WDT function through software programming for enable disable and in2. printf Test fail n return 1 getchar printf Test Pass n return 1 ROBO 8110VG2AR User s Manual BIOS Setup information Chapter 4 BIOS Setup Information RUBY PB6511 uses AMI BIOS structure stored in Flash ROM These BIOS has a built in Setup program that allows users to modify the basic system configuration easily This type of information is stored in CMOS RAM so that it is retained during power off periods When system is turned on RUBY PB6511 communicates with peripheral devices and checks its hardware resources against the configuration information stored in the CMOS memory If any error is detected or the CMOS parameters need to be initially defined the diagnostic program will prompt the user to enter the SETUP program Some errors are significant enough to abort the start up 4 1 Entering Setup Launch System Setup Power on the computer and the system will start POST Power On Self Test process When the message below appears on the screen press lt Del gt key will enter BIOS setup screen Press lt Del gt to enter SETUP If the message disappears before responding and still wish to enter Setup please restart the system by turning it OFF and On or pressing the RESET button It can be also restarted by pressing lt Ctrl gt lt Alt gt and lt Delete gt keys on keyboard simultaneously Press lt F1 gt to Run SETUP or Resume The BIOS setup program provides a General Help screen T
3. ROBO 8110VG2AR User s Manual 4 32 BIOS Setup information 4 5 Boot Use this menu to specify the priority of boot devices Aptio Setup Utility Copyright CH 2011 American Megatrends Inc Main Advanced Chipset Security Save 8 Exit Boot Configuration Number of seconds to wait for setup activation key Bootup NumLock State Off 65535 0xFFFF means indefinite waiting Quiet Boot 01sabl1ed CSM16 Module Verison 07 64 GateA20 Active Upon Request Option ROM Messages Force BIOS Interrupt 19 Capture Disabled Boot Option Priorities Select Screen ti Select Item Enter Select Change Opt Fi General Help Previous Values Optimized Defaults Save amp Exit Exit 2 11 1210 Copyright 2011 American Megatrends Inc Setup Prompt Timeout Number of seconds to wait for setup activation key 65535 0xFFFF means indefinite waiting Choices 1 65535 Bootup Num Lock State Select the keyboard Numlock state Setting to On will turn on the Num Lock key when the system is powered on Setting to Off will allow users to use the arrow keys on the numeric keypad Choices On Off ROBO 8110VG2AR User s Manual 4 33 BIOS Setup information Quiet Boot Enables or disables Quiet Boot option This BIOS feature determines if the BIOS should hide the normal POST messages with the motherboard or system manufacturer s full screen logo When it is enabled the BIOS will display the full
4. D5 SHIELD4 CLK CLK 2 10 System Installation Chapter 3 System Installation This chapter provides you with instructions to set up your system The additional information is enclosed to help you set up onboard PCI device and handle Watch Dog Timer WDT and operation of GPIO in software programming 3 1 Intel LGA 1155 Processor LGA 1155 CPU Socket Alignment key GE Alignment key AAA Pin1 corner of the CPU Socket LGA 1155 CPU Please remember to locate the alignment keys on the CPU socket of the motherboard and the notches on the CPU ROBO 8110VG2AR User s Manual 3 1 System Installation LGA 1155 CPU Installation Steps Before install the CPU please make sure to turn off the power first 1 Open the load lever 3 Remove the plastic cap on the CPU socket Before you install the CPU always cover it to protect the socket pin ROBO 8110VG2AR User s Manual 3 2 System Installation 4 After confirming the CPU direction for correct mating put down the CPU in the socket housing frame Note that alignment keys are matched 5 Make sure the CPU has been seated well into the socket If not take out the CPU and reinstall ROBO 8110VG2AR User s Manual 3 3 System Installation 7 Push the CPU socket lever back into its locked position 8 Please make sure four hooks are in proper position before you install the cooler 3 2 Main Memory ROBO 8110VG2AR provide 2
5. PIN No Signal Description PIN No Signal Description 1 Ground 2 Density Select 3 Ground 4 N C 5 N C 6 N C 7 Ground 8 Index 9 Ground 10 Motor ENA 11 Ground 12 N C 13 Ground 14 Drive Select A 15 Ground 16 N C 17 Ground 18 Direction 19 Ground 20 Step 21 Ground 22 Write Data 23 Ground 24 Write Gate 25 Ground 26 Track O 27 Ground 28 Write Protect 29 N C 30 Read Data 31 Ground 32 Head Select 33 N C 34 Disk Change 8 External PS 2 Keyboar ouse Connector 2 10 PIN No Signal Description PIN No Signal Description 1 Mouse Data 2 Keyboard Data 3 N C 4 N C 5 Ground 6 Ground 7 PS2 Power 8 PS2 Power 9 Mouse Clock 10 Keyboard Clock ROBO 8110VG2AR User s Manual 2 6 Hardware Configuration J9 SMBUS Connector EI OO T 5 Pin No Signal Description 1 SMBus_CLK 2 N C 3 Ground 4 SMBus_DAT 5 5V J10 12V POWER Connector Pin No Signal Description 1 Ground 2 Ground 3 12V 11 J12 J14 J15 External USB Connector 2 10 00000 000 1 PIN No Signal Description PIN No Signal Description 1 3 7 1 SV Dual EV Dal 3 UB KB 5 UB BH 7 God JI Ground Key nopin Im INC S O ROBO 8110VG2AR User s Manual 2 7 Hardware Configuration J13 CIR Connector KJOOOOdO 1 6 Pin No Signal Description 1 5V 2 N C 3 CIRRX 4 Ground 5 CIRTX 6 N C
6. s Manual 4 24 BIOS Setup information PCI Express Port Choices Disabled Enabled Auto PEG Force Gen PCI Express Port Force Gen1 Choices Disabled Enabled Detect Non Compliance Device Detect Non Compliance PCI Express Device in PEG Choices Disabled Enabled MRC Message Print Print Memory initialize message Choices Disabled Enabled South Bridge Aptio Setup Utility Copyright CH 2011 American Megatrends Inc Chipset Enabled Oisabled SMBUS SB Chipset Configuration Controller GbE Controller Enabled Wake on Lan from S5 Enabled Restore AC Power LOSS Power Off SLP_S4 Assertion Stretch Enable Enabled SLP_S4 Assertion Width 4 5 Seconds Deep Sx Disabled Audio Configuration Azalia HO Audio Enabled Azalia internal HOMI codec Disabled Select Screen Tk Select Item High Precision Event Timer Configuration Enter Select High Precision Timer Enabled Change Opt Fi General Help gt PCI Express Ports Configuration F2 Previous Values gt USB Configuration F3 Optimized Defaults F4 Save amp Exit ESC Exit Copyright C 2011 American Megatrends Inc SMBus Controller Choices Disabled Enabled Wake on Lan from 5 Enabled Disabled GbE control PME in S5 Choices Disabled Enabled ROBO 8110VG2AR User s Manual 4 25 BIOS Setup information Restore AC Power Loss Specify what state to go to when power is re applied after a power failure G3 State Ch
7. 23 F 140 F Storage Temperature 20 C 80 C Relative Humidity 5 90 non condensing ROBO 8110VG2AR User s Manual 1 6 System Overview 1 3 1 Mechanical Drawing e Fb 5 D SR j K Tg Ve ROBO 8110VG2AR User s Manual System Overview 1 4 System Architecture All of details operating relations are shown in ROBO 8110VG2AR series System Block Diagram BLOCK DIAGRAM Sandy Bridge Pere x16 or ml eon 3 1200 Dual Channel Memory BE e SATA 4 ports SATA 2 ports Backplane erer N GbE_82579LM K mr rere st N GbE 82574L mI RJ45 PICMG BP Cougar Point WS Froen USB 2 9 USE Interface I 1 Head eases come cane eee Realtek ALC662 Codec mey Bracket SPI Flash PICMG BP PCI E X1 4 OR PCI E X4 1 ror pur eme K CH7318B pink cH73188B DVI I a p SDVO I F PCH USB 10 13 Backplane Super I O Controller IT8721F Serial Port X2 IPC Bus TPM ROBO 8110VG2AR System Block Diagram ROBO 8110VG2AR User s Manual 1 8 Hardware Configuration Chapter 2 Hardware Configuration This chapter gives the definitions and shows the positions of jumpers headers and connectors All of the configuration jumpers on ROBO 8110VG2AR are in the proper position The default settings shipped from factory are marked with an asterisk 2 1 Jumper Setting In general jumpers on the single board computer are used to select options f
8. LPT LPTE Aptio Setup Utility Copyright C 2011 American Megatrends Inc Advanced Parallel Port Configuration Enable or Disable Parallel Port LPT LPTE Device Settings 10 378h IRQ 5 Change Settings Auto Device Mode Standard Parallel 4 Select Screen ti Select Item Enter Select Change Opt Fi General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 11 1210 Copyright C 2011 American Megatrends Inc Parallel Port Choices Disabled Enabled Change Settings Select an optimal setting for Super IO device Choices Auto IO 378h IRQ 5 IO 378h IRQ 5 6 7 10 11 12 IO 278h IRQ 5 6 7 10 11 12 IO 3BCh IRQ 5 6 7 10 11 12 IO 378h IO 278h O 3BCh ROBO 8110VG2AR User s Manual 4 19 BIOS Setup information H W Monitor Monitor hardware status Aptio Setup Utility Copyright C 2011 American Megatrends Inc Advanced Pc Health Status Fan Start Temperature Smart Fani Start 65 CPU Fan Duration 5 Smart Fan2 Control Enabled Smart Fan2 Start 65 System Fan Duration 5 System temperaturer 35 C CPU Temperature 42 C Fani Speed 2149 RPM Fan2 Speed N A Select Screen Vcore 1 164 V tk Select Item zl DN 1 512 V Enter Select 12V 12 073 V Change Opt 5V 45 076 V F1 General Help 3 3V 43 369 V F2 Previous Values VBAT 43 014 V F3 Optimized Defaults F4 Save 8 Exit ESC Exit Version 2 11 1
9. ROBO 8110VG2AR User s Manual BIOS Setup information Intel IGD SWSCI Configuration Intel IGD SWSCI OpRegion Function Aptio Setup Utliity Copyright C 2011 American Megatrends Inc Advanced Select DVMT Mode used by Intel IGO SWSCI OpRegion Configuration Internal Graphics Device DVMT FIXED Memory 256M6 IGO Boot Type VBIOS Default J Spread Spectrum Clock Disabled Select Screen Th Select Item Version 2 11 1210 Copyright C 2011 American Megatrends Inc DVMT Mode Select DVMT Mode used by Internal Graphic Device Choices Fixed Mode DVMT Mode DVMT FIXED Memory Select DVMT FIXED Mode Memory size used by Internal Graphic Device Choices 128MB 256MB Maximum IGD Boot Type Select the Video Device which will be activated during POST This has no effect if external graphics present Choices VBIOS Default CRT EFP EFP2 EFP3 CRT EFP Spread Spectrum Clock Choices Disabled Enabled ROBO 8110VG2AR User s Manual 4 14 BIOS Setup information USB Configuration USB Configuration Parameters Aptio Setup Utlilty Copyright CH 2011 American Megstrends Inc Advanced USB Configuration Enables Legacy USB support AUTO option disables legacy USB Devices support if no USB devices are 1 Keyboard 2 Hubs connected DISABLE option will keep USB devices available only for EFI applications EHCI Hand off Disabled Port 60 64 Emulation Enabled USB hardware delays and time outs
10. USB transfer time out 20 sec Device reset time out 20 sec Device power up delay Auto Select Screen tl Select Item Enter Select Change Opt General Help Previous Values Optimized Defaults Save amp Exit ESC Exit 11 1210 Copyright C 2011 American Megatrends Legacy USB Support Enables Legacy USB support AUTO option disables legacy support if no USB devices are connected DISABLE option will keep USB devices available only for EFI applications Choices Disabled Enabled Auto EHCI Hand Off This is a workaround for OSes without EHCI hand off support The EHCI ownership change should claim by EHCI driver Choices Disabled Enabled Port 60 64 Emulation Enables I O port 60h 64h emulation support This should be enabled for the complete USB keyboard legacy support for non USB aware OSes Choices Disabled Enabled USB transfer time out The Time out value for Control Bulk and Interrupt transfers Choices 1 sec 5 sec 10 sec 20 sec ROBO 8110VG2AR User s Manual 4 15 BIOS Setup information Device Reset time out USB mass storage device Start Unit command time out Choices 10 sec 20 sec 30 sec 40 sec Device Power up delay Maximum time the device will take before it properly reports itself to the Host Controller AUTO uses default value for a Root port it is 100ms for a Hub port the delay is taken from Hub descriptor Choices Auto Manual Info Report C
11. 8110VG2AR User s Manual Troubleshooting 5 2 BIOS Setting It is assumed that users have correctly adopted modules and connected all the devices cables required before turning on ATX power 240 pin DDR3 Memory keyboard mouse SATA hard disk VGA connector device power cables ATX accessories are good examples that deserve attention With no assurance of properly and correctly accommodating these modules and devices it is very possible to encounter system failures that result in malfunction of any device To make sure that you have a successful start with ROBO 8110VG2AR it is recommended when going with the boot up sequence to hit DEL key and enter the BIOS setup menu to tune up a stable BIOS configuration so that you can wake up your system far well Loading the default optimal setting When prompted with the main setup menu please scroll down to Restore Defaults press Enter and select Yes to load in default optimal BIOS setup This will force your BIOS setting back to the initial factory configuration It is recommended to do this so you can be sure the system is running with the BIOS setting that Portwell has highly endorsed As a matter of fact users can load the default BIOS setting any time when system appears to be unstable in boot up sequence Improper Disable Operation There are too many occasions where users disable a certain device feature in one application through BIOS setting These variabl
12. E1 05132011 Apacer PC3 8500 1GB 1 E PIDA J1108BABG DJ E Onboard Intel C206 Chipset Intel HD Graphics 1000 Family Version 6 14 10 5337 Onboard Intel 82574L Gigabit Network Connection Controller Intel 82574L Gigabit Network Connection Version 11 7 32 0 Onboard Intel 82579LM Gigabit Network Connection Controller Intel 82579LM Gigabit Network Connection Version 11 12 36 0 Onboard Realtek ALC662 High Definition Audio Controller Realtek ALC662 High Definition Audio Version 5 10 0 6343 Intel Chipset Device Software Version 9 2 0 1025 Intel 6 Series C200 Series Chipset Family USB Enhanced Host Controller Version 9 2 0 1021 Adaptec ASC 29160LP Seagate ST39173W 8 47GB WD WD1002FAEX 1TB SONY MPF920 E 1 44MB LITE ON LH 20A1S DVD ROM FSP400 60PFN PBPE 07P4 RO Intel Xeon CPU C5539 2 27GHz ES Bus Speed 133 3MHz L3 4M Project Version OABRB 0 19 x64 Build Date 01 20 2010 10 10 10 Apacer ECC DDR3 1066 1GB ELPIDA J1108BDBG DJ F 2 Onboard XGI Volari Z7 Z9 Z9s Z11 V1 11 03 XGI Volari Z7 Z9 Z9s Z11 Version 6 14 10 1110 Onboard Intel 82574L Gigabit Network Connection Intel 82574L Gigabit Network Connection Version 11 4 7 0 Intel Chipset Device Software Version 9 1 2 1002 Intel 5 Series 3400 Series Chipset Family USB Enhanced Host Controller Ver 9 1 1 1013 Seagate ST3160815AS Teac 1 44 Pioneer DVD 227A FSP350 60GLC PBPE 06P2 ROBO 8110VG2AR User s Manual 1 5 System Overview Operating Temperature 0 C 55 C
13. Express Support One slot Open 1 2 Short 3 4 reserved ROBO 8110VG2AR User s Manual 2 2 Hardware Configuration JP8 VCCSA Voltage Selection lo JP8 Function 1 2 Short 0 85 V 1 2 Open 0 925V JP11 SPI FLASH ROM Selection JP11 1 2 Short Normal Operation 2 3 Short 2 2 Connector Allocation I O peripheral devices and Flash disk will be connected to these interface connectors CONNECTOR FUNCTION REMARK J1 Parallel Port Connector J2 COMI Serial Port 1 Connector J3 COM2 Serial Port 2 Connector J4 J6 DDR3 Long SLOT J5 General Purpose I O Connector J7 Floppy Connector J8 External PS 2 Keyboard Mouse Connector J9 SMBus Connector J10 12V Power Connector Connect to CPU J11 J12 J14 J1 Internal USB Connector 5 J16 J17 External USB Connector J13 CIR Connector 6x1 pin header J20 J22 SATA 2 Connector J19 J23 SATA 3 Connector J21 Ethernet RJ 45 Connector LAN 1 82574L J25 Ethernet RJ 45 Connector LAN 2 82579LM J24 FAN 1 SYSTEN FAN Power Connector J30 FAN 2 CPU FAN Power Connector J26 Front Panel Pin HDR J28 Audio Connector J29 DVI Connector U1 HDMI Connector ROBO 8110VG2AR User s Manual 2 3 Hardware Configuration Parallel Port Connector J1 2 26 0000000000000 1 25 PIN No Signal Description PIN No Signal Description 1 Strobe 2 Auto Form Fe
14. Port USB Port USB Port USB Port USB Port Enabled Enabled Enabled Enabled Enabled Enabled Enabled Select Screen Enabled tt Select Item Enabled Enter Select Enabled Change Opt Enabled Fi General Help Enabled F2 Previous Values Enabled F3 Optimized Defaults Enabled F4 Save amp Exit ESC Exit woansrunseunrrsd ro ta ts rs LA P rs OH Copyright C 2011 American Megatrends Inc All USB Devices Enabled Disabled All USB Devices Choices Disabled Enabled EHCI Controller 1 2 Enabled Disabled USB2 0 EHCI Support Choices Disabled Enabled USB Port 0 13 Enabled Disabled USB Port 0 13 Choices Disabled Enabled ROBO 8110VG2AR User s Manual 4 31 BIOS Setup information ME Subsystem Aptio Setup Utiilty Copyright CH 2011 American Megstrends Inc Chipset ME Subsystem Help Intel ME Subsystem Configuration ME Version 7 1 10 1065 ME Temporary Disable Disabled End of Post Message Enabled Execute MEBx Enabled Select Screen ti Select Item Enter Select Change Opt Fi General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 11 1210 Copyright C 2011 American Megatrends Inc ME Subsystem Choices Enabled Disabled ME Temporary Disable Choices Enabled Disabled End of Post Message Choices Enabled Disabled Execute MEBx Choices Enabled Disabled
15. Setup Launch System Setup ena 4 1 AD E E 4 2 4 SAAVanNCed EE 4 3 FA CHI PSC E 4 23 45 Oger 4 33 ES GECULILY nn an eege eenegen eier Se 4 35 4 7 Save amp Exit EE 4 36 Chapter 5 Troubleshooting cccecccesecesseeeesneeeeeeeeeeeeeseaeseseeeeeeeeeseaesesaaesasneeeeeeeeseesaseaeeeneeeeeens 5 1 5 1 Hardware Quick Installation ee nara naaa anna 5 1 5 2 BIOS SOU nn na A AAA RE RERE E LATA Kali 5 2 JIFAQ EE 5 3 Appendix A Appendix B Preface How to Use This Manual The manual describes how to configure your ROBO 8110VG2AR system to meet various operating requirements It is divided into five chapters with each chapter addressing a basic concept and operation of Single Host Board Chapter 1 System Overview Presents what you have in the box and give you an overview of the product specifications and basic system architecture for this series model of single host board Chapter 2 Hardware Configuration Shows the definitions and locations of Jumpers and Connectors that you can easily configure your system Chapter 3 System Installation Describes how to properly mount the CPU main memory and Compact Flash to get a safe installation and provides a programming guide of Watch Dog Timer function Chapter 4 BIOS Setup Information Specifies the meaning of each setup parameters how to get advanced BIOS performance and update new BIOS In addition POST checkpoint list will give users so
16. screen logo during the boot up sequence hiding normal POST messages When it is disabled the BIOS will display the normal POST messages instead of the full screen logo Please note that enabling this BIOS feature often adds 2 3 seconds of delay to the booting sequence This delay ensures that the logo is displayed for a sufficient amount of time Therefore it is recommended that you disabled this BIOS feature for a faster boot up time Choices Disabled Enabled GateA20 Active UPON REQUEST GA20 can be disabled using BIOS services ALWAYS do not allow disabling GA20 this option is useful when any RT code is executed above IMB Choices Upon Request Always Option ROM Messages Set Display mode for Option ROM This item is used to determine the display mode when an optional ROM is initialized during POST When set to Force BIOS the display mode used by AMI BIOS is used Select Keep Current if you want to use the display mode of optional ROM Choices Force BIOS Keep Current Interrupt 19 Capture Enabled Allows Option ROMs to trap Int 19 Interrupt 19 is the software interrupt that handles the boot disk function When Enabled this BIOS feature allows the ROM BIOS of these host adaptors to capture Interrupt 19 during the boot process so that drives attached to these adaptors can function as bootable disks In addition it allows you to gain access to the host adaptor s ROM setup utility if one is available
17. 1 50 result 1 if inp GPIO_Base 0 amp 0x10 0x10 result 0 if inp GPIO_Base 2 amp 0xE0 0xE0 result 0 if result 0 printf Test fail n return 1 output low outp GPIO_Base 0 inp GPIO_Base 0 amp 0xF9 11 112 outp GPIO_Base 3 inp GPIO_Base 3 amp 0x7F 47 outp GPIO_Base 4 inp GPIO_Base 4 amp 0xFE 50 result 1 if inp GPIO_Base 0 amp 0x10 0x00 result 0 if inp GPIO_Base 2 amp 0xE0 0x00 result 0 if result 0 ROBO 8110VG2AR User s Manual System Installation printf Test fail n return 1 EE Set Input And_Register 0xC8 0xF9 11 12 And_Register OxCB 0x7F 47 And_Register OxCC 0xFE 50 Set output Or Register 0xC8 0x10 14 Or Register 0xCA 0xE0 35 36 37 output high outp GPIO_Base 0 0x10 14 outp GPIO_Base 2 0xE0 35 36 37 result 1 if inp GPIO_Base 0 amp 0x06 0x06 result 0 11 12 if inp GPIO_Base 3 amp 0x80 0x80 result 0 47 if inp GPIO_Base 4 amp 0x01 0x01 result 0 50 if result 0 printf Test fail n ROBO 8110VG2AR User s Manual 3 13 System Installation return 1 output low outp GPIO_Base 0 inp GPIO_Base 0 amp 0xEF 14 outp GPIO_Base 2 inp GPIO_Base 2 amp 0x1F 35 36 37 result 1 if inp GPIO_Base 0 amp 0x06 0x00 result 0 11 12 if inp GPIO_Base 3 amp 0x80 0x00 result 0 47 if inp GPIO_Base 4 amp 0x01 0x00 result 0 50 if result 0
18. 210 Copyright C 2011 American Megatrends Inc Smart Fan1 2 Control Smart CPU Fan Function Choices Disabled Enabled Smart Fan1 2 Start Smart CPU Fan start Temperature Setting Choices 25 30 35 40 45 50 55 60 65 70 CPU System Fan Duration Choices 0 1 2 3 4 5 6 7 8 9 10 ROBO 8110VG2AR User s Manual 4 20 BIOS Setup information AMT Configuration Aptio Setup Utility Copyright CH 2011 American Megatrends Inc Advanced Unconf igure AMT ME Disabled WatchDog Timer Disabled OS WatchDog Timer o BIOS WatchDog Timer Oo Select Screen Ti Select Item Enter Select Change Opt General Help gt Previous Values Optimized Defaults F4 Save amp Exit Esc Exit Version 2 11 1210 Copyright C 2011 American Megatrends Inc AMT Choices Disabled Enabled Unconfigure AMT ME Choices Disabled Enabled WatchDog Timer Choices Disabled Enabled ROBO 8110VG2AR User s Manual 4 21 BIOS Setup information Serial Port Console Redirection Aotio Setup Utility Copyright CH 2011 American Megatrends Inc Advanced Console Redirection Enable or COMO Disable gt Console Redirection Settings COM1 Pci Bus0 Dev0 FuncO Disabled Console Redirection Port Is Disabled Serial Port for Out of Band Management Windows Emergency Management Services EMS Console Redirection Enabled gt Console Redirection Settings Select Screen tl Select Item Ente
19. J24 System Fan Connector nee 1 3 Pin No Signal Description 1 Ground 2 Fan speed control 3 Fan on off output J30 CPU Fan Connector 1 4 Pin No Signal Description 1 Ground 2 12V 3 Fan on off output 4 Fan Speed control ROBO 8110VG2AR User s Manual 2 8 Hardware Configuration J26 Front Panel Pin HDR 2 16 5 00000000 oc0000ooo WI 1 1 PIN No Signal Description PIN No Signal Description Speaker C NC C 1 PWRILED X 2 PWRILEDG 5 J35 LAN1_ACT J O7 O 9 e 1 3 5 eee 7 J25 LANILINK 8 21 LAN2_LINK 11 28 Audio MIC Line in Line out Connector 2 0000 Goooo 1 9 PIN No Signal Description PIN No Signal Description MIC with Reference Analog Ground Voltage 3 Line in Left Channel J4 5 Line in Right Channel 6 AnalogGround 7 Line out Left Channel 8 AnalogGround _ 9 Line out RightChannel 10 NC 1 3 5 7 ROBO 8110VG2AR User s Manual 2 9 Hardware Configuration 28 Audio MIC Line in Line out Connector PIN Signal PIN No Description No i D gt lo 2 D2 3 4 5 D4 6 7 8 C1 C2 Green LO C3 Blue IL c4 Iso CG AGNDI C6 A GND2 C1 Red oo ROBO 8110VG2AR User s Manual Signal Description CS1 CG2 Q O ray Q Q N PIN No 17 18 19 20 21 22 23 24 Signal Description D0 DU SHIELD3 D5
20. LDN outp SIO_Port 0x07 outp SIO_Port 1 LDN printf LDN x n LDN Set register offset to Value void Set_Register unsigned char offset unsigned char value outp SIO_Port offset outp SIO_Port 1 value printf Write offset x x n offset value Or register void Or_Register unsigned char offset unsigned char value outp SIO_Port offset outp SIO_Port 1 inp SIO_Port 1 value printf Write offset x x n offset value And register void And_Register unsigned char offset unsigned char value outp SIO_Port offset outp SIO_Port 1 inp SIO_Port 1 amp value printf Write offset x x n offset value int main void ROBO 8110VG2AR User s Manual 3 10 System Installation int result printf ROBO 8110 GPIO Test n pini 11 pin3 12 pin5 47 pin7 50 pin2 14 pin4 35 pin6 36 pin8 37 Enter_IT872x_SIO Set_LDN GPIO_LDN Enable GPIO Or_Register 0xC0 0x46 11 12 14 Or_Register 0xC2 0xE0 35 36 37 Or_Register 0xC3 0x80 47 Or_Register 0xC4 0x01 50 Set Output Or_Register 0xC8 0x06 11 12 Or_Register 0xCB 0x80 47 Or_Register 0xCC 0x01 50 Set Input ROBO 8110VG2AR User s Manual 3 11 System Installation And_Register 0xC8 0xEF 14 And_Register OxCA 0x1F 35 36 37 output high outp GPIO_Base 0 0x06 11 12 outp GPIO_Base 3 0x80 47 outp GPIO_Base 4 0x0
21. ROBO 38110VG2AR Single Host Board User s Manual Version 1 0 Copyright Portwell Inc 2011 All rights reserved All other brand names are registered trademarks of their respective owners Preface Table of Contents How to Use This Manual Chapter 1 System OVerview ccccccccesceesseeeeeneeeeeeeeeceseseeeneeeeeeeeeeanaaeenseaeseneesseaesaseeeenseeeeseesenaas 1 1 TT Vr th CCRC E 1 1 12 CHEEK E 1 2 eeh 1 3 System C Onli ura ton E 1 5 1 31 Mechanical e 1 7 LA System Architecture na naa arii A Ana Ka haa Ak akan 1 8 Chapter 2 Hardware Configuration sseeeeeesan anna naaa aaa nennen aaa nennen nennen aan aan anna 2 1 2 Jumper Seting need A An de in Aril 2 1 ZA Commector AMO ON San a il EE ERREGE REN TE E 2 3 Chapter 3 System Installation nn ireen eadein aaiae SA AAA aoea SAN A a 3 1 3 1 Intel LGA 1155 Processor sennen aaa a a 3 1 32 Man Memory aieeaii Ea E E A Pere SMA An ANA 3 4 3 3 Installing the Single Board Computer 3 5 3 3 1 Chipset Component Driver aa 3 5 3 3 2 Chipset Component Driver aaa 3 5 3 3 3 On board Gigabit Ethernet Controllers ma 3 5 3 0 4 Audio ie 3 6 Se Clear CMOS Operation getrei alegre ninakaa lada 3 6 3D WDT Ee EE 3 7 RE ato eee net Ae pte Kena So An ld eh nk Ae ce taal at ce 3 9 Chapter 4 BIOS Setup InformatioOn s eeeeeeeee ema aaa naaa aan nee nennen nenen anakan aan anna 4 1 4 1 Entering
22. SERR Generation Disabled PCI Express Device Settings Relaxed Ordering Disabled Extended Tag Disabled No Snoop Enabled Maximum Payload Auto Select Screen Maximum Read Request Auto ti Select Item Enter Select PCI Express Link Settings Change Opt ASPM Support Disabled General Help WARNING Enabling ASPM may cause some Previous Values PCI E devices to fail Optimized Defaults Extended Synch Disabled Save amp Exit ESC Exit CH 2011 American Megatrends Inc PCI ROM Priority In case of multiple Option ROMs Legacy and EFI Compatible specifies what PCO Option ROM to launch Choices Legacy ROM EFI Compatible ROM PCI Latency Timer Value to be programmed into PCI Latency Timer Register Choices 32 PCI Bus Clocks 64 PCI Bus Clocks 96 PCI Bus Clocks 128 PCI Bus Clocks 160 PCI Bus Clocks 192 PCI Bus Clocks 224 PCI Bus Clocks 248 PCI Bus Clocks VGA Palette Snoop Choices Disabled Enabled PERR Generation Enables or Disables PCI Device to Generate PERR Choices Disabled Enabled SERR Generation Enables or Disables PCI Device to Generate SERR Choices Disabled Enabled Choices Disabled Enabled ROBO 8110VG2AR User s Manual 4 4 BIOS Setup information Relaxed Ordering Choices Disabled Enabled Extended Tag If Enabled allows Device to use 8 bit Tag field as a requester Choices Disabled Enabled No Snoop Choices Disabled Enabled Maximu
23. Sleep State Select the highest ACPI Sleep state the system will enter when the SUSPEND button is pressed Choices Suspend Disabled 51 CPU Stop Clock 53 Suspend to RAM Lock Legacy Resources Enables or Disables Lock of Legacy Resources Choices Enabled Disabled ROBO 8110VG2AR User s Manual 4 6 BIOS Setup information Trusted Computing Aptio Setup Utility Copyright C 2011 American Megatrends Inc Advanced TPM Configuration Enables or Disables TPM support 0 S will not show TPM Reset of platform is required Current TPM Status Information NO TPM Hardware Select Screen ti Select Item Enter Select Change Opt General Help Previous Values Optimized Defaults Save amp Exit ESC Exit TPM SUPPORT Enables or Disables TPM support The choice Disabled Enabled WHEA Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc Advanced Enable or disable Windows Hardware Error architecture e Select Screen ti Select Item Enter Select Change Opt General Help Previous Velues Optimized Defaults Save amp Exit Exit ROBO 8110VG2AR User s Manual BIOS Setup information WHEA SUPPORT Enables or Disables Windows Hardware Error Architecture The choice Disabled Enabled S5 RTC Wake Settings Aptio Setup Utility Copyright CH 2011 American Megatrends hr min sec specified F3 Optimized Defaults F4 Save amp Exi
24. When Disabled the ROM BIOS of these host adaptors will not be able to capture Interrupt 19 Therefore you will not be able to boot operating systems from any bootable disks attached to these host adaptors Nor will you be able to gain access to their ROM setup utilities ROBO 8110VG2AR User s Manual BIOS Setup information Choices Disabled Enabled Boot Option 1 Sets the system boot order Choices Built in EFI Shell other bootable devices Disabled 4 6 Security Use this menu to set supervisor and user passwords Aptio Setup Utility Copyright C 2011 American Megatrends Inc GEIER a Security i Password Description Set Setup Administrator Password If ONLY the Administrator s password is set then this only limits access to Setup and is only asked for when entering Setup If ONLY the User s password Le set then this is a power on password and must be entered to boot or enter Setup In Setup the User will have Administrator rights The password must be 3 to 20 characters long User Password Select Screen ti Select Item Enter Select Change Opt Fi General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit j Copyright C 2011 American Megatrends Inc Administrator Password Set Setup Administrator Password User Password Set User Password ROBO 8110VG2AR User s Manual 4 35 BIOS Setup information 4 7 Save amp Exit This menu allows you to lo
25. ad the BIOS default values or factory default settings into the BIOS and exit the BIOS setup utility with or without changes Aptio Setup Utility Copyright C 2011 American Megatrends Inc EIER PAM et Re AA Save amp Exit Reset the system after saving Olscard Changes and Reset the changes Restore Defaults Boot Override Launch EFI Shell from filesystem device Select Screen ti Select Item Enter Select Change Opt Fi General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit 1 1210 Copyright CH 2011 American Megatrends Inc Save Changes and Reset Reset the system after saving the changes Pressing lt Enter gt on this item asks for confirmation Save configuration and reset Discard Changes and Exit Reset system setup without saving any changes Restore Defaults Restore Load Default values for all the setup options Launch EFI Shell from filesystem device To enter the Built in EFI shell for further modification such as upgrade BIOS Built in EFI Shell Boot into the initial shell environment it can debug and dump the PCI Resource or jump to next bootable device If it doesn t have boot device it will return to BIOS setup menu If you want to know the shell command you can visit the Intel official hyperlink as below http software intel com en us articles uefi shell Internal_ EFI Shell Comm ands ROBO 8110VG2AR User s Manual 4 36 Troubl
26. al Troubleshooting Answer You can simply short 2 3 pins on JP9 to clean your password Question How to update the BIOS file of the ROBO 8110VG2AR Answer 1 Please visit web site of the Portwell download center as below hyperlink and register an account http www portwell com tw support newmember ph 2 Input your User name and password to log in the download center 3 Select the Search download to input the keyword ROBO 8110VG2AR 4 Find the BIOS page to download the ROM file and flash utility 5 Execute the zip file to root of the bootable USB pen drive 6 Insert your bootable USB pen drive in ROBO 8110VG2AR board and power on 7 Input the AFUDOS XXXXX ROM p b n to start to update BIOS XXXXX is the file name of the ROM file 8 Switch Off the Power Supply when you finished the update process 9 To short the JP9 jumper from 1 2 short to 2 3 short 5 seconds then set back to 1 2 short Clear CMOS 10 Switch ON the Power Supply then press the del key to BIOS to load Restore Defaults and then select Save Changes and Exit option Note Please visit our technical web site at http www portwell com tw For additional technical information which is not covered in this manual you can mail to tsd mail portwell com tw or you can also send mail to our sales they will be very delighted to forward them to us System Memory Address Map Each On board de
27. ation 1 IDE Mode 2 AHCI Mode 3 RAID Mode Serial ATA Controller 0 Compatible Serial ATA Controller 1 Enhanced SATA Porto Not Present SATA Porti Not Present SATA Port2 Not Present SATA Port3 Not Present Select Screen SATA Port4 Not Present tl Select Item Enter Select SATA PortS Not Present Change Opt Fi General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit Esc Exit Yersion 2 11 1210 Copyright C 2011 American Megatrends Inc SATA Mode Select IDE AHCI Configuration Choices Disable IDE Mode AHCI Mode Serial ATA Controller 0 Enabled Disabled Serial ATA Controller 0 Choices Disabled Enhanced Compatible Serial ATA Controller 1 Enabled Disabled Serial ATA Controller 1 Choices Disabled Enhanced ROBO 8110VG2AR User s Manual BIOS Setup information Thermal Configuration Aotio Setup Utility Copyright CH 2011 American Megstrends Inc Advanced Thermal Configuration Enabled Disabled ME SMBus Thermal Reporting Configuration Thermal Data Reporting Enabled SMBus Buffer Length 20 Thermal Reporting EC PEC Disabled PCH Temo Read Enabled Select slots with TS on DIMM Thermal Sensor on DIMMO Oisabled Thermal Sensor on DIMM2 Disabled Select Screen Alert Enable Lock Disabled ti Select Item PCH Alert Disabled Enter Select DIMM Alert 0isabled Change Opt General Help Previous Values Optimized Defaults it Save am
28. cket on the bottom of chassis to balance and support SBC from bending System Overview Chapter 1 System Overview 1 1 Introduction ROBO 8110VG2AR the PICMG 1 3 SHB Single Host Board supports the Intel Core i3 and Xeon processor The attractive Corei3 and Xeon E3 1200 family processors not only posses amazing parallel computing power but also support ECC memory That makes the system more powerful The SHB adopted Intel C206 chipset and Core i3 Xeon E3 1200 family processors The Core i3 Xeon E3 1200 family processors integrated Intel integrated graphics engine that supports 3D performance DirectX 10 1 Shader model 4 0 and OpenGL 3 0 More than that user could utilize even higher end the latest PCI Express x16 interface graphics card via backplane ROBO 8110VG2AR built with dual Intel Gigabit Ethernet Four DDR3 long DIMM sockets support system memory up to 16GB Two SATA 600 ports and Four SATA 300 ports dual ports via backplane support RAID 0 1 5 10 Support multiple display by DVI I DVI D VGA on bracket and HDMI ports To meet bandwidth of storage and expansion cards requirement the ROBO 8110VG2AR was designed flexible with four PCI Express lanes via backplane Those four PCI Express lanes could be four PCI Express x1 links or one PCI Express x4 link by different bios support Four PCI Express x1 links configuration can support more PCI Express x1 devices via backplane and one PCI Express x4 link configuratio
29. e ESC Exit SLP S4 Assertion Stretch Enable Choices Disabled Enabled SLP S4 Assertion Width Choices 1 2 2 3 3 4 4 5 seconds High Precision timer Choices Disabled Enabled Wakeup by Ring Choices Disabled Enabled ROBO 8110VG2AR User s Manual 4 29 BIOS Setup information PCI Express Ports Configuration All PCI Express Ports can be set as choices Disabled Enabled Auto Ap io Setup wriiity Copyright C 2003 American Megatrends Inc Chipset PCI Express Ports Configuration Enable or Disable the PCI Express Ports in the Chipset PCI Express Port PCI Express Port PCI Express Port PCI Express Port PCI Express Port PCI Express Port PEI Express Port 6 Select Screen ti Select Item Enter Select Change Opt Fi General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit PCI Express Port 1 2 3 4 5 6 Choices Disabled Enabled Auto PCIe Sub Decode Enabled Disabled PCle Sub Decode Port This option is available when Subtractive Decode Agent Enable PCHTrap9 14 1b Choices Disabled Enabled ROBO 8110VG2AR User s Manual BIOS Setup information USB Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc Chipset USB Configuration Enabled Disabled All USB Devices EHCI Controller 1 Enabled EHCI Controller 2 Enabled USB Port USB Port USB Port USB Port USB Port USB Port USS Port USB Port USB Port USB
30. ed 3 Data 4 Error 5 Datal 6 Initialization 7 Data2 8 Printer Select IN 9 Data3 10 Ground 11 Data4 12 Ground 13 Data5 14 Ground 15 Data6 16 Ground 17 Data7 18 Ground 19 Acknowledge 20 Ground 21 Busy 22 Ground 23 Paper Empty 24 Ground 25 Printer Select 26 NC J2 COM1 Serial Port 2 10 OOOO OO OO0 SX 9 PIN No Signal Description 1 DCD 2 DSR 3 RXD 4 RTS 5 TXD 6 CTS 7 DTR 8 RI 9 Ground 10 N C ROBO 8110VG2AR User s Manual 2 4 Hardware Configuration J3 COM2 Serial Port 2 Connector 2 10 00000 aooo 1 9 Signal Description DCD Data Carrier Detect a ae DATA DSR Data Set Ready NC NC RS 232 RS 422 RS 485 RXD Receive Data DATA S TX Wis X I C X N T 5 TXD Transmit Data R 6 CTS CleartoSend NC N C 8 RI Ring Indicator GND Ground 0 N C Note J3 COM2 could be configurable as RS 232 422 485 with jumper JP1 J5 General Purpose I O Connector 2 10 00000 go000 1 9 Signal Description GPIO0 2 GPIO4 GPIO1 GPIO5 GPIO2 GPIO6 GPIO3 8 GPIO7 9 Ground 10 5V Note All General Purpose I O ports can only apply to standard TTL 5 signal level 0V 5V and each Fan ROBO 8110VG2AR User s Manual 2 5 Hardware Configuration 7 Floppy Interface 2 34 00000000000000000 1 GOOOO00000 0000000 1 33
31. es may not be set back to the original values when needed These devices features will certainly fail to be detected When the above conditions happen it is strongly recommended to check the BIOS settings Make sure certain items are set as they should be These include the Serial Port1 Serial Port 2 ports USB ports external cache on board VGA and Ethernet It is also very common that users would like to disable a certain device port to release IRQ resource A few good examples are Disable Serial Port1 to release IRQ 4 Disable Serial Port2 to release IRQ 3 Etc ROBO 8110VG2AR User s Manual Troubleshooting A quick review of the basic IRQ mapping is given below for your reference IRQ Description Usable IRQ 5 3 FAQ Symptom SBC keeps beeping and no screen has shown Solution In fact each beep sound represents different definition of error message Please refer to table as following Beep sounds Meaning Action One long beep with one DRAM error Change DRAM or reinstall it short beeps One long beep DRAM error Change DRAM or reinstall it constantly One long beep with two Monitor or Display Please check Monitor connector short beeps Card error whether it inserts properly Beep rapidly Power error warning Please check Power mode setting Information amp Support Question I forget my password of system BIOS what am I supposed to do ROBO 8110VG2AR User s Manu
32. eshooting Chapter 5 Troubleshooting This chapter provides a few useful tips to quickly get ROBO 8110VG2AR running with success As basic hardware installation has been addressed in Chapter 2 this chapter will primarily focus on system integration issues in terms of BIOS setting and OS diagnostics 5 1 Hardware Quick Installation ATX Power Setting Unlike other Single board computer ROBO 8110VG2AR supports ATX only Therefore there is no other setting that really needs to be set up However there are only two connectors that must be connected J10 4 pins CPU 12V main power connector amp 24 pins ATX Power Connector Serial ATA Hard Disk Setting for IDE AHCI Unlike IDE bus each Serial ATA channel can only connect to one SATA hard disk at a time there are total six connectors J19 amp J20 J22 J23 Four ports on board those 4 Masters in Non AHCI mode two support 6Gb two support 3Gb and two ports route to backplane support 3Gb because SATA hard disk doesn t require setting up Master and Slave which can reduce mistake of hardware installation All you need to operate IDE and AHCI application for system please follow up setting guide in BIOS programming Table 5 1 Furthermore you can consult chapter 4 3 Advanced SATA Configuration part of the SATA Mode Hard Drive Serial ATA Power Cable Serial ATA Data Cable Table 5 1 SATA Mode setting guide System BIOS Main Menu Advanced ROBO
33. he menu can be easily called up from any menu by pressing lt F1 gt The Help screen lists all the possible keys to use and the selections for the highlighted item Press lt Esc gt to exit the Help screen General Help Move Seiect gt Vaive 9 Exit Generasi Help gt Previous Values gt Optimized Defaults Seve amp Exit Setup ROBO 8110VG2AR User s Manual 4 1 BIOS Setup information 4 2 Main Use this menu for basic system configurations such as time date etc Aptio Setup Utility Copyright C 2011 American Megatrends Inc Advanced Chinset BIOS Information BIOS Vendor Core Version Comp liency Project Version Build Date and Time Memory Information Total Memory System Date System Time Access Level Security Save 2 Exit American Megatrends 4 6 4 0 UEFI 2 0 1APBB 0 04 x64 07 12 2011 15 27 27 4096 MB DORI 1333 ked 07 13 2011 15 15 50 Administrator Choose the system default language Select Screen Ti Select Item Enter Select Change Opt General Help Previous Values Optimized Defaults Save amp Exit ESC Exit Version 2 11 1210 Copyright E 2011 American Megatrends Inc BIOS Information Memory Information These items show the firmware and memory specifications of your system Read only System Language oose the system default language Choices English System Time The time format is lt Hour gt lt Minute g
34. ight C 2011 American Megatrends Inc PCI Express Port 1 2 3 4 5 6 Choices Disabled Enabled Auto PCIe Sub Decode Enabled Disabled PCle Sub Decode Port This option is available when Subtractive Decode Agent Enable PCHTrap9 14 1b ROBO 8110VG2AR User s Manual 4 27 BIOS Setup information Software Memory Test Choices Disabled Enabled Patrol Scrub Choices Disabled Enabled Demand Scrub Choices Disabled Enabled Fast MRC Choices Disabled Enabled DDR3 Memory Operating Speed Choices Auto 1333MHz 1067MHz 800MHz Memory Rank Margining Choices Auto 1333MHz 1067MHz 800MHz Closed Loop Throttling Choices Disabled Enabled Open Loop Throttling Choices Disabled Enabled DIMM Information Display DIMM presence and size information ROBO 8110VG2AR User s Manual 4 28 BIOS Setup information South Bridge Configuration Chipset SB Chipset Configuration SLP_S4 Assertion Stretch Enable SLP_S Assertion Width ccopurignt C 2993 American Megatrencs Inc Enable Disable SMBus Controller Enabled 4 5 Seconds High Precision Event Timer Configuration High Precision Timer Wakeup by Ring gt PCI Express Ports Configuration P USB Conf igurat lon SMBus Controller Choices Disabled Enabled Enabled Enabled Select Screen Th Select Item Enter Select Change Opt Fl General Help F2 Previous Values F3 Optimized Defaults F4 Sav
35. m Payload Set Maximum Payload of PCI Express Device or allow System BIOS to select the value Choices Auto 128 Bytes 256 Bytes 512 Bytes 1024 Bytes 2048 Bytes 4096 Bytes Maximum Read Request Set Maximum Read Request size of PCI Express Device or allow System BIOS to select the value Choices Auto 128 Bytes 256 Bytes 512 Bytes 1024 Bytes 2048 Bytes 4096 Bytes ASPM Support Set the ASPM Level Force LO Force all links to LO State AUTO BIOS auto configure DISABLE Disables ASPM Choices Disabled Auto Force LO Extended Synch If Enabled allows generation of Extended Synchronization patterns Choices Disabled Enabled ROBO 8110VG2AR User s Manual 4 5 BIOS Setup information ACPI Settings Aptio Setup Utility Copyright CH 2011 American Megatrends Inc Advanced ACPI Settings Enables or Disables BIOS ACPI Auto Configuration Enable Hibernation Enabled ACPI Sleep State S3 Suspend to RAM Lock Legacy Resources Disabled Select Screen IL Select Item Enter Select Change Opt Fi General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 11 1210 Copyright CH 2011 American Megatrends Inc Enabled ACPI Auto Configuration Choices Enabled Disabled Enabled Hibernation Enables or Disables System ability to Hibernate OS S4 Sleep State This option may be not effective with some OS Choices Enabled Disabled ACPI
36. m that is written in C language User can fill a non zero value into the Time out Value Register to enable refresh WDT System will be reset after the Time out Value to be counted down to zero Or user can directly fill a zero value into Time out Value Register to disable WDT immediately To ensure a successful accessing to the content of desired Control Register the sequence of following program codes should be step by step run again when each register is accessed Additionally there are maximum 2 seconds of counting tolerance that should be considered into user application program For more information about WDT please refer to IT8728F CXS data sheet There are two PNP I O port addresses that can be used to configure WDT 1 Ox2E EFIR Extended Function Index Register for identifying CR index number 2 0x2F EFDR Extended Function Data Register for accessing desired CR Below are some example codes which demonstrate the use of WDT include lt stdio h gt include lt conio h gt include lt dos h gt define SIO Port Ox2E define SIO_Port2 Ox4E define GPIO_LDN 0x07 void Enter_IT872x_SIO ROBO 8110VG2AR User s Manual 3 7 System Installation SIO_ Port 0x87 outportb SIO_Port 0x01 outportb outportb outportb J SIO_Port 0x55 SIO_Port 0x55 J NNN NNN void Set_LDN unsigned char LDN outportb SIO_Port 0x07 outportb SIO_Port 1 LDN printf LDN x n LDN
37. me guidelines of trouble shooting Chapter 5 Troubleshooting Provides various useful tips to quickly get ROBO 8110VG2AR running with success As basic hardware installation has been addressed in Chapter 3 this chapter will basically focus on system integration issues in terms of backplane setup BIOS setting and OS diagnostics The content of this manual is subject to change without prior notice These changes will be incorporated in new editions of the document Portwell may make supplement or change in the products described in this document at any time Updates to this manual technical clarification and answers to frequently asked questions will be shown on the following web site http www portwell com tw Preface Notice SBC Handling and Installation Notice H Handling and Installing SBC Caution Do not just hold any single side of the SBC hold evenly on both sides Heavy processor cooler may bend the SBC when SBC being held just on one side The bending may cause soldering or components damaged Preface H Fix your SBC in System Caution Suggest your S I or vendor to use a metal bracket to hold fix the desktop or server grade SBC to avoid the vibration damage during transportation Heavy processor cooler may bend the SBC when systems are during transportation without any holder Example 4U chassis gt Use L type mental or plastic or rubber bracket to hold SBC 2U or 1U chassis a mental bra
38. n can support RAID card or special add on cards such as image processing board In addition the flexible configuration can be leveraged with bridge on backplane to support more PCI or PCI X slots that benefits industries with legacy support PCI Express x16 from processors can be one PCI Express x16 or two PCI Express x8 or One PCI Express x8 Two PCI Express x4 by jumper setting It ll be very flexible for customer to adopt with server or non server BP Advanced Management Technology AMT 7 0 is feature that ROBO 8110VG2AR equipped with Xeon E3 1200 family processors Core i3 doesn t support AMT This technology provides remote access capability via Intel Gigabit Ethernet controller The new technology is a hardware based solution that uses out of band communication for system management access to client systems Beside that the hardware and software information can be gathering by 3 4 party software then storage in SPI interface EEPROM Therefore asset management could be done at the same time ROBO 8110VG2AR User s Manual 1 1 System Overview ROBO 8110V G2AR features Support Intel Xeon E3 1200 family and Core i3 processor in an LGA1155 socket Two 240 pin DDR3 ECC SDRAM DIMM socket support for DDR3 1333 1066 DIMMs up to 16GB system memory Intel Xeon E3 1200 family and Core i3 processor integrated graphic engine that supports MPEG 2 Decode DirectX 10 1 OpenGL 3 0 and Shader Model 4 0 Equipped dual Intel Gigabit Etherne
39. oices Power Off Power On Last State SLP S4 Assertion Stretch Enable Enabled Disabled SLP_S4 Assertion Stretch Choices Disabled Enabled SLP S4 Assertion Stretch Width Select a minimum assertion width of the SLP_S4 Assertion signal Choices 1 2 Seconds 2 3 Seconds 3 4 Seconds 4 5 Seconds Deep Sx Deep Sx configuration Note Mobile platforms support Deep 54 55 in DC only and Desktop platforms support Deep 54 55 in AC only Choices Disabled Enabled in S5 Battery Enabled in S5 Enabled in 54 and S5 Battery Enabled in 54 and S5 Azalia HD Audio Enabled Disabled Azalia HD Audio Choices Disabled Enabled Azalia Intermal HDMI codec Enabled Disabled internal HDMI codec for Azalia Choices Disabled Enabled High Precision Timer Enabled Disabled the High Precision Event Timer Choices Disabled Enabled ROBO 8110VG2AR User s Manual 4 26 BIOS Setup information PCI Express Ports Configuration Aptio Setup Utility Copyright CH 2011 American Megatrends Inc Chipset PCI Express Ports Configuration Enabled Disabled the PCI Express Ports in the Chipset PCI Express Port Auto PCI Express Port Auto PCI Express Port Auto PCI Express Port Auto PCI Express Port Auto PCIe Sub Decode Disabled Select Screen tl Select Item Enter Select Change Opt Fi General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 11 1210 Copyr
40. onfiguration Aptio Setup Utility Copyright C 2011 American Megatrends Inc Advanced Info Report Configuration Post Report Error Message Report Info Error Message Disabled Summary Screen Summary Screen 01sab1ed Version 2 11 1210 Copyright EC Post Report Choices Disabled Enabled Info Error Message Choices Disabled Enabled Summary Screen Choices Disabled Enabled ROBO 8110VG2AR User s Manual Post Report Support Enabled Disabled Select Screen ti Select Item Enter Select Change Opt Fi General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit 2011 American Megatrends Inc BIOS Setup information Super IO Configuration Aptio Setup Utility Copyright CH 2011 American Megstrends Inc Advanced Super IO Configuration Set Parameters of Floppy Disk Controller FOC Super I0 Chip gt Serial Port o Configuration gt Serial Port 1 Configuration gt Parallel Port Configuration Select Screen tl Select Item Enter Select Change Opt Fi General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 11 1210 Copyright C 2011 American Megatrends Inc Floppy Disk Controller Configuration Aptio Setup Utility Copyright CH 2011 American Megatrends Inc Advanced Floppy Disk Controller Configuration Enable or Disable Floppy Olsk Controller Device Settings Rese
41. or certain features Some of the jumpers are designed to be user configurable allowing for system enhancement The others are for testing purpose only and should not be altered To select any option cover the jumper cap over SHORT or remove NC it from the jumper pins according to the following instructions Here NC stands for Not Connect 622 5055 Ee W Tr e E Besse Lassosssssesss G O emm O PI 5 io 0 0 oI lo LI D J3 Ji cooooocooooooooooo Ul CT ceo n3 7 Do 00000000000000 pl Hr Zeg messes wl CO JP2 was A J10 IP35 Eaa 120 J19 E Es ea a JJA D 126 p soa bes BHO 338 J28 129 838 000 O SC H Wm H UHT II HH a DUNN DD ROBO 8110VG2AR User s Manual 2 1 Hardware Configuration JP1 COM2 J3 Interface Selection 2 22 Oooo00000000 gooo9000000 1 21 JP1 Function 5 6 9 11 10 12 15 17 16 18 Short RS 232 3 4 7 9 8 10 13 15 14 16 21 22 Short RS 422 1 2 7 9 8 10 19 20 Short RS 485 JP2 ATX AT Mode Select JO 1 2 Short AT Mode 1 2 Open ATX Mode JP2 Function JP5 CMOS Clear JP5 Function JP7 Function 1 x8 2 x4 PCI Express Support Three slot 2 x8 PCI Express Support Two slot 1 x16 PCI
42. p Exit ESC Exit 2 11 1210 Copyright CH 2011 American Megatrends Inc ME SMBus Thermal Reporting Enabled Disabled ME SMBus Thermal Reporting Configuration Choices Disabled Enabled Thermal Data Reporting Choices Disabled Enabled SMBus Buffer Length SMBus Block Read message length for EC Choices 1 2 5 9 10 14 20 Thermal Reporting EC PEC Enable Packet Error Checking PEC for SMBus Block Read Choices Disabled Enabled PCH Temp Read PCH Temperature Read Enable Choices Disabled Enabled Thermal Sensor on DIMMO Choices Disabled Enabled ROBO 8110VG2AR User s Manual 4 12 BIOS Setup information Thermal Sensor on DIMM2 Choices Disabled Enabled Alert Enable Lock Lock all Alert Enable settings Choices Disabled Enabled PCH Alert Choices Disabled Enabled DIMM Alert Choices Disabled Enabled Intel TXT LT Configuration Aptio Setup Utility Copyright CH 2011 American Megatrends Inc Advanced Intel Trusted Execution Technology Configuration Intel TXT support only can be enabled disabled if SMX 1s enabled VT and VT d support must also be enabled prior to TXT Secure Mode Extensons SMX Disabled Intel TXT LT Support Disabled Select Screen ti Select Item Enter Select Change Opt Fi General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 11 1210 Copyright C 2011 American Megatrends
43. r Select Change Opt Fi General Help F2 Previous Values F3 Optimized Defaults Fa Save amp Exit ESC Exit Yersion 2 11 1210 Copyright C 2011 American Megatrends Inc Console Redirection Setting Aptio Setup Utility Copyright CH 2011 American Megatrends Inc Advanced Microsoft Kindows Emergency Terminal Type VT UTF8 Management Services EMS Bits per second 115200 allows for remote management Flow Control None of a Windows Server 0S through Data Bits 8 a serial port Parity None Stop Bits 1 Select Screen tk Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 11 1210 Copyright C 2011 American Megatrends Inc ROBO 8110VG2AR User s Manual 4 22 BIOS Setup information Out Of Band Mgmt Port Choices COMO COM1 Terminal Type Choices VT100 VT100 VT uTF8 ANSI Bits per second Choices 9600 19200 57600 115200 Flow Control Choices None Hardware RTS CTS Software Xon Xoff 4 4 Chipset This menu controls the advanced features of the onboard North Bridge and South Bridge Aptio Setup UtLlifty Copyright CH 2011 American Megstrends Inc ePrice Chipset RITTER OCH EH North Bridge Parameters gt South Bridge gt ME Subsystem Select Screen tl Select Item Enter Select Change Opt Fi General Help F2 Previous Values F3 Optimized Defaul
44. r Cores Number of cores to Enabled in each processor package Choices All 1 2 3 Limit CPUID Maximum Disabled for Windows XP Choices Disabled Enabled Execute Disabled Bit XP can prevent certain classes of malicious buffer overflow attacks when combined with a supporting OS Windows Server 2003 SP1 Windows XP SP2 SuSE Linux 9 2 RedHat Enterprise 3 Update 3 Choices Disabled Enabled ROBO 8110VG2AR User s Manual 4 9 BIOS Setup information Hardware Prefetcher To turn on off the MLC streamer prefetcher Choices Disabled Enabled Adjacent Cache Line Prefetch To turn on off the prefetching of adjacent cache lines Choices Disabled Enabled Intel Virtualization Technology When enabled a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology Choices Disabled Enabled Power Technology Enabled the power management features Choices Disabled Energy Efficient Custom Long duration power limit Long duration power limit in Watts Choices 0 255 Long duration maintained Time window which the long duration power is maintained Choices 0 32000 Short duration power limit Short duration power limit in Watts Choices 0 255 ROBO 8110VG2AR User s Manual 4 10 BIOS Setup information SATA Configuration SATA Devices Configuration Choices Enabled Disabled Aptio Setup Utility Copyright CH 2011 American Megatrends Inc Advanced SATA Configur
45. sable IRQ IBM Mouse Event Coprocessor Error Hard Disk Event Usable IRQ ROBO 8110VG2AR User s Manual 5 5
46. t lt Second gt Use or to configure system Time System Date The date format is lt Day gt lt Month gt lt Date gt lt Year gt Use or to configure system Date ROBO 8110VG2AR User s Manual 4 2 BIOS Setup information 4 3 Advanced Use this menu to set up the items of special enhanced features Aptio Setup Utlifty Copyright CH 2011 American Megatrends Inc Main Advanced Chipset Boot Security Save amp Exit North Bridge Parameters gt South Bridge gt ME Subsystem Select Screen tl Select Item Enter Select Change Opt Fi General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Yersion 2 11 1210 Copyright C 2011 American Megatrends Inc Launch PXE OpROM Enabled or Disabled Boot Option for Legacy Network Devices Choices Disabled Enabled Launch Storage OpPROM Enabled or Disabled Boot Option for Legacy Mass Storage devices Choices Disabled Enabled ROBO 8110VG2AR User s Manual 4 3 BIOS Setup information PCI Subsystems Settings PCI PCI X and PCI Express Settings Aptio Setup Utility Copyright CH 2011 American Megsatrends Inc Advanced PCI Bus Oriver Version V 2 03 00 In case of multiple Option ROMS Legacy and EFI Compatible specifies what PCI Common Settings Settings PCI Option ROM to launch PCI Latency Timer 32 PCI Bus Clocks VGA Palette Snoop Disabled PERR Generation Disabled
47. t ESC Exit Wake system with Fixed Time Enabled or Disabled system wake on alarm event When Enabled system will wake on the hr min sec specified Choices Disabled Enabled ROBO 8110VG2AR User s Manual BIOS Setup information CPU Configuration These items show the advanced specifications of your CPU Read only Aptio Setup Utility Copyright C 2011 American Megatrends Inc Advanced CPU Configuration Socket specific CPU Information CPU Speed 3300 MHZ 64 bit Supported Hyper threading Enabled Active Processor Cores A11 Limit CPUID Maximum Execute Disable Bit Hardware Prefetcher 0isabled Enabled Enabled Adjacent Cache Line Prefetch Enabled Intel Virtualization Technology Disabled Select Screen tk Select Item Enter Select Change Opt Fi General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Power Technology Energy Efficient Factory long duration power limit 65 Watts Long duration power Limit 0 Factory long duration maintained 1000 ms Long duration maintained 0 Recommended short duration power 1 1 25 Long Duration Short duration power Limit 0 Hyper Threading Enabled for Windows XP and Linux OS optimized for Hyper Threading Technology and Disabled for other OS OS not optimized for Hyper Threading Technology When Disabled only one thread per enabled core is enabled Choices Disabled Enabled Active Processo
48. t Required Change Settings Auto Device Mode Read brite Select Screen tl Select Item Enter Select Change Opt Fi General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 11 1210 Copyright C 2011 American Megatrends Inc ROBO 8110VG2AR User s Manual BIOS Setup information Floppy Disk Controller Choices Disabled Enabled Change Settings Choices Auto IO 3F0h IRQ 6 DMA 2 IO 3F0h IROQ 3 4 5 6 7 10 11 12 DMA 2 3 10 370h IRQ 3 4 5 6 7 10 11 12 DMA 2 3 Device Mode Choices Read Write Write Protect Serial Port 0 1 Configuration Aptio Setup Utility Copyright CH 2011 American Megstrends Inc Advanced Serial Port o Configuration Enable or Disable Serial Port COM Device Settings I0 3F8h IRQ 4 Change Settings Auto Select Screen ti Select Item Enter Select Change Opt Fi General Help Previous Values Optimized Defaults Save amp Exit ESC Exit Version 2 11 1210 Copyright C 2011 American Megatrends Inc Serial Port Choices Disabled Enabled Change Settings Select an optimal setting for Super IO Device Choices Auto IO 3F8h IRQ 4 IO 3F8h IRQ 3 4 5 6 7 10 11 12 O 2F8h IRQ 3 4 5 6 7 10 11 12 1O 3E8h IRQ 3 4 5 6 7 10 11 12 IO 2E8h IRQ 3 4 5 6 7 10 11 12 ROBO 8110VG2AR User s Manual 4 18 BIOS Setup information Parallel Port Configuration Set Parameters of Parallel Port
49. t ports Support iAMT 7 0 Support two SATA 600 and four SATA 300 ports dual ports via backplane One PCI Express x16 external expansion one PCI Express x4 link can be configured as four PCI Express x1 and four PCI devices via backplane The PICMG 1 3 SHB is the best solution of applications such like flight simulation image processing broadcasting and so on that need performance of display and storage 1 2 Check List The ROBO 8110VG2AR package should cover the following basic items SRR RR SON One ROBO 8110VG2AR single host board One dual Serial ports cable kit One single Parallel port cable kit One FDD cable One 7 pin SATA 300 signal cable One SATA 600 signal cable One Installation Resources CD Title Optional One bracket with PS 2 keyboard and mouse If any of these items is damaged or missing please contact your vendor and keep all packing materials for future replacement and maintenance ROBO 8110VG2AR User s Manual 1 2 System Overview 1 3 Product Specification Main processor Intel Xeon E3 1200 family and Core i3 Processor e BIOS AMI system BIOS with SPI Serial CMOS EEPROM with easy upgrade function ACPI DMI Green function and Plug and Play Compatible Main Memory Support dual channel DDR3 memory interface ECC non buffered DIMMs only Two DIMM sockets support 1333 1066 DDR3 SDRAM up to 16GB System Memory L2 Cache Memory Built in Processor Chipset Intel C206 chipset
50. terval setting Generate system reset On board VGA Processors integrated graphics share system memory up to 1GB for system with greater than or equal to 192MB of system memory On board Ethernet LAN Dual Intel PCI Express x1 interface based Gigabit Ethernet to support RJ 45 connector e High Driving GPIO Support 8 programmable high driving GPIO Cooling Fans Support one 4 pin power connector for CPU fan and one 3 pin power connector for system fan System Monitoring Feature Monitor CPU temperature system temperature and major power sources etc Bracket Support dual Ethernet port with 2 indicators dual USB ports and one DVI I port Outline Dimension L X W 338 5mm 13 33 X 126 39mm 4 98 Power Requirements 12V CPU 4 85A 12V System 2 43A 5V 3 4A Test Programs BurnIn Test V6 0 Run Time Full loading Test configuration ROBO 8110VG2AR User s Manual 1 4 System Overview CPUType SBC BIOS Memory VGA Card VGA Driver LAN Card LAN Driver LAN Card LAN Driver Audio Card Audio Driver Chip Driver USB 2 0 Driver SCSI Card SCSI HDD SATA HDD FDD CDROM Power Supply Back plane CPU Type SBC BIOS Memory VGA Card VGA Driver LAN Card LAN Driver Chip Driver USB 2 0 Driver SATA HDD FDD CDROM Power Supply Back plane System Configuration Intel Core i7 2600 Processor 8M Cache 3 40 GHz ES Portwell Inc ROBO 8110VG2AR BIOS Rev R1 10
51. tion 3 3 1 to 3 3 4 to install INF VGA LAN Audio drivers 3 3 1 Chipset Component Driver ROBO 8110VG2AR uses Intel Cougar Point workstation C206 chipset It s a new chipset that some old operating systems might not be able to recognize To overcome this compatibility issue for Windows Operating Systems such as Windows XP please install its INF before any of other Drivers are installed You can find very easily this chipset component driver in ROBO 8110VG2AR CD title 3 3 2 Intel Integrated Graphics CMCH Chip ROBO 8110VG2AR uses Intel PCH integrated graphic engine to gain an outstanding graphic performance ROBO 8110VG2AR supports DVI I HDMI dual display This combination makes ROBO 8110VG2AR an excellent piece of multimedia hardware Drivers Support Please find the Graphic drivers in the ROBO 8110VG2AR CD title Drivers support Windows XP Win7 3 3 3 On board Gigabit Ethernet Controllers Drivers Support Please find Intel 82579LM and 82574L LAN drivers in Ethernet directory of ROBO 8110VG2AR CD title The drivers support Windows XP Win 7 ROBO 8110VG2AR User s Manual 3 5 System Installation 3 3 4 Audio Controller Please find Realtek ALC662 GR High Definition Audio driver form ROBO 8110VG2AR CD title The drivers support Windows XP Win7 3 4 Clear CMOS Operation The following table indicates how to enable disable Clear CMOS Function hardware circuit by putting jumpers at proper position P5 CLEAR CMOS JP5 F
52. ts F4 Save amp Exit ESC Exit Yersion 2 11 1210 Copyright C 2011 American Megatrends Inc ROBO 8110VG2AR User s Manual 4 23 BIOS Setup information North Bridge Aptio Setup Utility Copyright CH 2011 American Megstrends Inc Chipset Memory Information Low MMIO resources align at 64MB 1024MB Total Memory 4096 MB DORI 1333 Memory Sloto 4096 MB DORI 1333 Memory Slot2 O MB DORI 1333 vT d Disabled Initate Graphic Adapter PEG IGD IGO Memory 64M Render Standby Enabled t Select Screen IGO Multi Monitor Disabled ti Select Item Enter Select PCI Express Port Auto Change Opt PEG Force Gent Disabled General Help Detect Non Compliance Device Disabled Previous Values Optimized Defaults MRC Message Print Disabled F4 Save amp Exit ESC Exit Version 2 11 1210 Copyright C 2011 American Megatrends Inc Low MMIO Align Low MMIO resources align at 64MB 1024MB Choices 64M 1024M VI d Choices Disabled Enabled Intel Graphic Adapter Select which graphics controller to use as the primary boot device Choices IGD PCI IGD PCI PEG PEG IGD PEG PCI IGD Memory IGD Share Memory Size Choices Disabled 32M 1024M Render Standby Enable Disable Render Standby by Internal Graphics Device Choices Disabled Enabled IGD Multi Monitor Enable Disable IGD Multi Monitor by Internal Graphics Device Choices Disabled Enabled ROBO 8110VG2AR User
53. unction 1 2Short Normal Operation 2 3 Short Clear CMOS Contents 3 ray 00000 00000 0000000000000 WO Goooe Doooo Il Do00000000000 ch ajo 0 0 0 D ooo Do 00000000000000 00000000000000000 Q ooo fig Dez poco Bai kaecg leo _ 000 000 E A ELLE loo 00000 Sooo Flo 0 00 TTD ln on oT ul 1 23 ROBO 8110VG2AR User s Manual 3 6 System Installation 3 5 WDT Function The working algorithm of the WDT function can be simply described as a counting process The Time Out Interval can be set through software programming The availability of the time out interval settings by software or hardware varies from boards to boards ROBO 8110VG2AR allows users control WDT through dynamic software programming The WDT starts counting when it is activated It sends out a signal to system reset or to non maskable interrupt NMI when time out interval ends To prevent the time out interval from running out a re trigger signal will need to be sent before the counting reaches its end This action will restart the counting process A well written WDT program should keep the counting process running under normal condition WDT should never generate a system reset or NMI signal unless the system runs into troubles The related Control Registers of WDT are all included in the following sample progra
54. vice in the system is assigned a set of memory addresses which also can be identical of the device The following table lists the system memory address used for your reference Memory Area Size Description 0000 003F 1K Interrupt Area 004 0 004F 0 3K BIOS Data Area 0050 006F 0 5K System Data 0070 0OE2E 54K DOS OE2F OF6B 5K Program Area OF6C 9BFF 562K Available ROBO 8110VG2AR User s Manual 5 4 Troubleshooting First Meg Conventional memory end at 624K 9C00 9D3F 5K Extended BIOS Area 9D40 9FFF 11K Unused A000 AFFF 64K VGA Graphics BO00 B7FF 32K Unused B800 BFFF 32K VGA Text C000 CD7F 54K Video ROM CD80 EFFF 138K Unused F000 FFFF 64K System ROM HMA 64K First 64K Extended Interrupt Request Lines IRQ Peripheral devices can use interrupt request lines to notify CPU for the service required The following table shows the IRQ used by the devices on board Interrupt Request Lines IRQ IRQ Current Use IRQ 0 System ROM IRQ 1 System ROM IRQ2 Unassigned IRQ 3 System ROM IRQ 4 System ROM IRQ5 Unassigned IRQ 6 System ROM IRQ7 Unassigned IRQ 8 System ROM IRQ 9 Unassigned IRQ 10 Unassigned IRQ 11 Video ROM IRQ 12 System ROM IRQ 13 System ROM IRQ 14 System ROM IRQ 15 Unassigned Default Use System Timer Keyboard Event Usable IRQ COM2 COM1 Usable IRQ Diskette Event Usable IRQ Real Time Clock Usable IRQ Usable IRQ U
55. void Set_Register unsigned char offset unsigned char value outportb SIO_Port offset outportb SIO_Port 1 value printf Write offset x x n offset value int main void printf test string n Enter_IT872x_SIO Set_LDN GPIO_LDN Set_Register 0x72 0xC0 Set_Register 0x73 0x05 printf System will reset in 5 seconds n return 0 ROBO 8110VG2AR User s Manual 3 8 System Installation 3 6 GPIO The ROBO 8110VG2AR provides 8 programmable input or output ports that can be individually configured to perform a simple basic I O function Users can configure each individual port to become an input or output port by programming register bit of I O Selection To invert port value the setting of Inversion Register has to be made Port values can be set to read or write through Data Register J5 General Purpose I O Connector PIN No Signal Description PIN No Signal Description CO 2 GPIO4 GPIO1 GPIO5 GPIO2 GPIO6 GPIO3 GPIO7 9 Ground 10 Is o include lt stdio h gt include lt conio h gt include lt stdlib h gt define SIO_ Port 0x2E define SIO_Port2 Ox4E define GPIO_LDN 0x07 define GPIO_Base 0x0A00 Enter SIO void Enter_IT872x_SIO outp SIO_Port 0x87 outp SIO_Port 0x01 J outp SIO_Port 0x55 outp SIO_Port 0x55 J ROBO 8110VG2AR User s Manual 3 9 System Installation Select LDN void Set_LDN unsigned char
56. x240 pin DIMM sockets Dual Channel which supports Dual channel 1066 1333 DDR3 SDRAM as main memory Non ECC Error Checking and Correcting non register functions The maximum memory can be up to 16GB Memory clock and related settings can be detected by BIOS via SPD interface For system compatibility and stability do not use memory module without brand Memory configuration can be set to either one double sided DIMM in one DIMM socket or two single sided DIMM in both sockets Beware of the connection and lock integrity from memory module to socket Inserting improperly it will affect the system reliability Before locking make sure that all modules have been fully inserted into the card slots Note To insure the system stability please do not change any of DRAM parameters in BIOS setup to modify system the performance without acquired technical information ROBO 8110VG2AR User s Manual 3 4 System Installation 3 3 Installing the Single Board Computer To install your ROBO 8110VG2AR into standard chassis or proprietary environment please perform the following Step 1 Check all jumpers setting on proper position Step 2 Install and configure CPU and memory module on right position Step 3 Place ROBO 8110VG2AR into the dedicated position in the system Step 4 Attach cables to existing peripheral devices and secure it WARNING Please ensure that SBC is properly inserted and fixed by mechanism Note Please refer to sec
Download Pdf Manuals
Related Search