USER MANUAL www.philips.com/welcome Type HD8772 EN 02
Contents
1. Remove the water tank rinse it and fill it up to the MAX level with fresh water Place it back into the machine When inserting the water tank into the machine the following display is shown Empty the drip tray and coffee grounds drawer and place them back in position EE Empty the container back and place it back under both the steam hot water wand and the dispensing spout IB Press the button to start the rinse cycle Yellow fq When this icon is displayed the water tank is empty Repeat steps 12 15 When the machine shows this icon again go to step 17 Red 50 ENGLISH TALC CLEAN ESC 1 Green Yellow When the water tank is empty remove the water tank rinse it and fill it up to the MAX level with fresh water Place it back into the machine EE Empty the container back and place it back under both the steam hot water wand and the dispensing spout EE When the amount of water needed for the rinse cycle has been com pletely dispensed this icon on the side is displayed Press the ef wh button to quit the descaling cycle Press the button to prime the circuit The machine now carries out the warm up and automatic rinse cycle to prepare for product brewing Remove and empty the container Empty the drip tray and place it back The descaling cycle is now complete Remove the small white filter and replace the INTE2. 4 4 very hard water The letters correspond to the references that are located at the base of the INTENZA water filter see next chapter Zl Press the lE button and scroll the pages by pressing the button until the following icon is displayed Note The machine is supplied with a standard water hardness setting suitable for most types of water PHILIPS wm Saeco i Q Ai Yellow Green ENGLISH 13 EJ Press the button to increase the value or the button to de crease the value KA Press the E button to confirm the setting Press the f tp button to exit the programming MENU The machine shows this display and is ready to brew INTENZA Water Filter Installation We recommend that you install the INTENZA water filter as this prevents limescale build up in your machine and preserves a more intense aroma of your coffee The INTENZA water filter can be purchased separately For further de tails please refer to the maintenance products page in this manual Water is a crucial part of every espresso coffee so it s important to always have it professionally filtered Using the INTENZA water filter will prevent mineral deposits from building up and improve your water quality E Remove the small white filter from the water tank and store it in a dry place Remove the INTENZA water filter from its pa
3. The beverage is too weak See note The beverage is brewed slowly See note Clean the dispensing spout Brew a few cups of coffee as described in the Saeco Adapting System chapter Change coffee blend or adjust the grind as explained in the Adjusting the Ceramic Coffee Grinder chapter The circuit is not primed Prime the circuit see Using the Machine for the First Time chapter The brew group is dirty Coffee leaks out of the dis pensing spout Milk does not froth The dispensing spout is clogged The Automatic Milk Frother is in serted too deep No milk is being suctioned Frothed milk is too cold The cups are cold Note Clean the brew group see Weekly Cleaning of the Brew Group chap ter Clean the dispensing spout and its holes Leave the Automatic Milk Frother to cool down Move it slightly down wards Reposition it in its correct seat Preheat the cups with hot water These problems can be considered normal if the coffee blend has been changed or if the machine has just been installed In this case wait until the machine performs a self adjusting operation as described in the Saeco Adapting System chapter 60 ENGLISH ENERGY SAVING Stand b The Saeco full automatic espresso machine is designed for energy saving proven by the Class A energy label After 30 minutes of inactivity the machine turns off automatically unless a different stand
4. To make a good quality cappuccino use cold milk 5 C 41 F with a protein content of at least 3 Whole milk or skimmed milk may be used depending on individual taste imu Note When you plan to dispense steam right after switching on the machine or after brewing a coffee some water still present in the circuit may need to be dispensed first For this press the g wp button and then the Ep but ton to dispense steam for a few seconds Thereafter press the button to stop Continue with step 2 FJ Insert the suction tube into the Automatic Milk Frother EJ Insert the Automatic Milk Frother until it locks in place in the steam wand seat BB caution Make sure that the suction tube outer surface is clean for hygienic reasons EJ Plunge the suction tube in the milk container 28 ENGLISH STEAM HOT WATER i O COFFEE STRENGT Yellow Green EJ Place a cup under the Automatic Milk Frother KA Press the of ep button The machine shows this display Press the Ep button to start dispensing steam Steam dispensing automatically stops after a continued use of 3 minutes Press the tp button then the Zp button to start dispensing steam again EJ The following icon is displayed during pre heating time required by the machine EJ When this icon is displayed the machine dispenses frothed milk directly in the cup
5. chapter of this manual If you want to descale later press the KAASA button to continue using the machine Please note that not descaling your machine will ultimately make it stop working properly In this case repair is NOT covered under your warranty ENGLISH 57 Warning Signals Red Color 30 30 30 Exx Completely insert the drip tray with the coffee grounds drawer into the ma chine and close the service door Fill the coffee bean hopper The brew group must be inserted into the machine Empty the coffee grounds drawer Wait about 5 seconds before placing it back Set the ESPRESSO or COFFEE selection lever to ESPRESSO within 30 seconds to complete brewing Set the ESPRESSO or COFFEE selection lever to COFFEE within 30 seconds to complete brewing Fill the water tank A beverage has been selected without the coffee bean hopper inner lid on the machine Place the coffee bean hopper inner lid on the machine within 30 seconds to complete brewing Turn off the machine After 30 seconds turn it on again Try this 2 or 3 times If the machine will not start contact the Philips SAECO hotline in your coun try and quote the error code shown on the display You can find its contact details in the warranty booklet packed separately or on www philips com support 58 ENGLISH TROUBLESHOOTING Thi
6. Saeco Miiunute USER MANUAL Type HD8772 Read carefully before using the machine iy CE Register your product and get support at www philips com welcome IMPORTANT SAFEGUARDS When using electrical appliances basic safety precautions should always be followed including the following 1 2 3 8 9 Read all instructions Do not touch hot surfaces Use handles or knobs To protect against fire electric shock and injury to persons do not immerse cord plugs or appliance in water or other liquid Close supervision is necessary when the appliance is used by or near children Unplug from outlet when not in use and before cleaning Allow to cool before putting on or taking off parts and before cleaning the appliance Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner Return appliance to the nearest authorized service facility for examination repair or adjustment The use of accessory attachments not recommended by the appliance manufacturer may result in fire electric shock or injury to persons Do not use outdoors Do not let cord hang over edge of table or counter or touch hot surtaces 10 Do not place on or near a hot gas or electric burner or in a heated oven 11 Always attach plug to appliance first then plug cord into wall outlet To disconnect turn any control to off then remove plug from
7. Green ENGLISH 31 CLEANING AND MAINTENANCE Daily Cleaning of the Machine BEB caution Timely cleaning and maintenance of your machine is very important as it prolongs the life of your machine Your machine is continuously exposed to moisture coffee and limescale The activities you need to perform and their frequency are described in detail in this chapter Not doing this will ultimately make your machine stop working properly This repair is NOT covered by your warranty mall Note Use a soft dampened cloth to clean the machine Only the cup holder grill and the Automatic Milk Frother can be washed in the dishwasher All other components must be washed with lukewarm water Do not immerse the machine in water Do not use alcohol solvents and or abrasive objects to clean the machine Donot dry the machine and or its components using a microwave and or standard oven E Empty and clean the coffee grounds drawer and the drip tray daily with the machine turned on Other maintenance operations can only be carried out when the machine is turned off and unplugged EJ Remove the coffee grounds drawer and empty it EJ Empty and clean the drip tray 32 ENGLISH Qj Insert the coffee grounds drawer back into the drip tray and this into the machine m Note Also empty the drip tray when the full drip tray indicator is raised Daily Cleaning of the Water Tank EE Remove the sm
8. The espresso is not creamy The blend is unsuitable coffee is Change coffee blend or adjust the enough not freshly roasted or the grindis degree of grind as explained in See note too coarse the Adjusting the Ceramic Coffee Grinder chapter The machine takes a long The machine circuit is clogged by Descale the machine time to warm up or the limescale amount of water dispensed is too little The brew group cannot be The brew group is out of place Turn the machine on Close the ser removed vice door The brew group automati cally returns to the initial position The coffee grounds drawer is Remove the coffee grounds drawer inserted before removing the brew group Machine actions Causes The machine grinds the There is no water coffee beans but no coffee comes out ENGLISH 59 Solutions Fill the water tank and prime the circuit see Using the Machine for the First Time chapter See note The brew group is dirty Clean the brew group see Weekly Cleaning of the Brew Group chap ter The circuit is not primed Prime the circuit see Using the Machine for the First Time chapter This might occur when the ma chine is automatically adjusting the dose Brew a few cups of coffee as described in the Saeco Adapting System chapter The dispensing spout is dirty This might occur when the ma chine is automatically adjusting the dose The coffee grind is too fine
9. Aroma Beverage Strength Adjusting the Dispensing Spout ESPRESSO or COFFEE selection lever Adjus Brewing an Espresso using Coffee Beans Brewing an Espresso using Pre Ground Coffee BREWING A COFFEE Brewing a Coffee Using Coffee Beans Brewing a coffee Using Pre Ground Coffee TE DISPENSING STEAM CAPPUCCINO BREWING sssssesseoseosesseeoseoseossoesossoseossossoseose 27 HOT WATER DISPENSING scssssssssssssssssesscesscesssesscesscesssessnessnessnessnesenenenenes CLEANING AND MAINTENANCE Daily Cleaning of the Machine Daily Cleaning of the Water Tank Daily Cleaning of the Automatic Milk Frother Weekly Cleaning of the Machine Weekly Cleaning of the Brew Group Monthly Cleaning of the Automatic Milk Frother Monthly Lubrication of the Brew Group Monthly Cleaning of the Brew Group with Coffee Oil Remover 44 Monthly Cleaning of the Coffee Bean Hopper is DESCALING PROGRAMMING The following settings can be adjusted How to Program the Machine MEANING OF THE DISPLAY ICONG ssscscssssssssssssssssecssscsssssesscsesesecssssssceseees TROUBLESHOOTING ssscssssssssssssssssscessssssesscsssssesscsssesecsssssesessssesecssessesecees ENERGY SAVING Stand by Disposal TECHNICAL SPECIFICATIONS cccscssssssssssssssessssssssesscsssesecsssssecsssssesecsssssssecers WARRANTY AND SERVICE Warranty Service ORDERING MAINTENAN
10. Automatic Milk Frother from the machine EE Remove the rubber grip from the steam wand BEB caution Warning The tube could be hot if the machine has recently been used ENGLISH 41 GD Take off the suction tube To detach the Automatic Milk Frother press the sides and remove it by applying light lateral movements as shown in the figure Remove the rubber lid as shown in the figure Wash all the components with lukewarm water Attach the lid by pressing in the middle and ensure that it is firmly in place 42 ENGLISH Attach the Automatic Milk Frother to the fitting and ensure it is locked into place in its seat Install the suction tube Insert the rubber grip back on the steam wand BEB caution Warning The tube could be hot if the machine has recently been used BEB caution Do not insert the rubber grip further than the seat shown In this case the Automatic Milk Frother would not function correctly as it would not be able to draw up milk y Insert the Automatic Milk Frother on the rubber grip until it locks into place ENGLISH 43 Monthly Lubrication of the Brew Grou Lubricate the brew group after approximately 500 cups of coffee or once a month The grease to lubricate the brew group can be purchased separately For further details please refer to the maintenance products page in this manual BEB caution Before lubricating the brew group clean it with fre
11. by time has been programmed If a product has been brewed the machine performs a rinse cycle In stand by mode the energy consumption is below 1Wh To turn on the machine press the y button if power button on the back of the machine is set to I If the boiler is cold the machine performs a rinse cycle Disposal Do not throw away the machine with the normal household waste at the end of its life but hand it in at an official collection point for recycling By doing this you help to preserve the environment The packing materials can be recycled Machine unplug the machine and cut the power cord Deliver the appliance and power cord to a service centre or public waste disposal facility This product complies with EU Directive 2002 96 EC ay The symbol on the product or on its packaging indicates that this product may not be treated as household waste Instead it must be handed over to the appropriate waste collection centre for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local council office your household waste disposal service or the shop where you purchased the product ENGLISH 61 TECHNICAL S
12. extra strong aroma pre ground coffee Green Green 18 ENGLISH Adjusting the Dispensing Spout The height of the dispensing spout can be adjusted to better fit the dimensions of the cups that you wish to use The lower part of the dispens ing spout can be removed to allow a tumbler to be used Move the dispensing spout up or down with your fingers to adjust its height as shown in the image The recommended positions are For the use of small cups For the use of large cups Two cups can also be placed under the dispensing spout to brew two cups of espresso at the same time ENGLISH 19 Remove the lower part of the dispensing spout to allow a tumbler to be used Before installing the lower part of the dispensing spout clean it together with the upper part ESPRESSO or COFFEE selection lever The machine allows you to adjust the brewing pressure according to the desired beverage type This selection allows you to optimize machine operation to improve the quality of coffee brewing and the desired result in the cup This selection must be made prior to brewing a beverage by simply mov ing manually the lever positioned on the dispensing spout 20 ENGLISH Red The lever allows two types of brewing Hl Push the lever downwards to select the ESPRESSO function In this position you can brew an espresso coffee by pressing the
13. minute EJ Place a container under the dispensing spout to catch the small amount of water which will be dispensed The machine shows this display Wait for the cycle to finish automati cally EJ When the above steps are complete the machine shows this display You can now perform the manual rinse cycle 10 ENGLISH Manual Rinse Cycle During this process you activate the coffee brewing cycle and fresh water flows through the water circuit This takes a few minutes El Place a container under the dispensing spout Check that the machine shows this display Green EJ Select the pre ground coffee brewing function by pressing the 4 button The machine shows this display e Green Do not add pre ground coffee to the compartment EJ Check that the selection lever is set to ESPRESSO Press the 5 but ton The machine starts dispensing water E When the dispensing has finished empty the container Repeat the operations from step 1 to step 4 twice then continue with step 6 K Place a container under the steam wand STEAM HOT WATER g wo STEAM HOT WATER COFFEE STRENGTH Green ENGLISH 11 EJ Press the button to start dispensing hot water EJ Dispense water until the no water icon appears You can interrupt the manual rinsing by pressing the S button To restart press thee but
14. ready to brew products The machine is ready to brew pre ground coffee Steam or hot water selection Hot water dispensing Steam dispensing The machine is brewing one cup of espresso The machine is brewing two cups of espresso The machine is programming the amount of espresso to brew Espresso brewing using pre ground coffee in progress ENGLISH 55 Ready Signals Green Color The machine is brewing one cup of medium coffee STOP oF The machine is programming the amount of medium coffee to be brewed EME STOP The machine is brewing one cup of long coffee SOP The machine is programming the amount of long coffee to be brewed 56 ENGLISH Warning Signals Yellow Color STOP S SS Fi 2s a8 4 R Sa START START ESG TALC CLEAN The machine is in warm up phase to brew beverages or dispense hot water steam The machine is performing the rinse phase Wait until the machine has com pleted the cycle The machine needs the INTENZA water filter to be replaced The brew group is being reset due to machine reset Refill the coffee bean hopper with coffee beans Put back the coffee bean hopper lid and restart the cycle Prime the circuit The machine needs to be descaled Press the 8 button to start the descal ing process Follow the steps described in the Descaling
15. CE PRODUCTS INSTALLATION Product Overview ENGLISH 5 General Description BEY MY R WN a 17 18 19 20 Grease for the brew group 22 23 24 21 25 32 Grinder adjustment knob Coffee bean hopper Pre ground coffee compartment Water tank Lid Coffee bean hopper lid Control panel Espresso coffee dispensing spout Full drip tray indicator Cup holder grill Drip tray Coffee grounds drawer Brew group Coffee residues drawer Service door Espresso Coffee selection lever Steam wand rubber grip for Automatic Milk Frother also for hot water dispensing Automatic Milk Frother also for steam dispensing Suction tube for Automatic Milk Frother Power cord socket Power button Power cord Water hardness test strip Coffee grinder adjustment key Pre ground coffee scoop Cleaning brush 26 27 28 29 30 31 ON OFF button 33 Espresso brew button Medium coffee brew button Long coffee brew button Hot water steam button Aroma Pre ground coffee button Menu button Descaling solution to be purchased separately 6 ENGLISH PREPARING FOR USE Machine Packagin The original packaging has been designed and constructed to protect the machine during transport We recommend keeping the packaging material for possible future transport Machine Installation E Remove the machine from th
16. Clean the coffee bean hopper once a month when it is empty with a damp cloth to remove coffee oil Thereafter refill it with coffee beans ENGLISH 47 DESCALING CALC CLEAN PHILIPS _ Saeco Yellow The descaling process takes approx 35 minutes Limescale builds up inside the machine during use It needs to be removed regularly as it may clog the water and coffee circuit of your machine The machine tells you when descaling is needed If the machine display shows the CALC CLEAN icon it means that you need to descale it BB caution Not doing this will ultimately make your machine stop working prop erly and in this case repair is NOT covered by your warranty Always use the specially formulated descaling solution since it has been designed to optimize machine performance The descaling solution can be purchased separately For further details please refer to the maintenance products page in this manual PN warning Never drink the descaling solution or any products dispensed until the cycle has been carried out to the end Never use vinegar as a descaling solution ki Note During the descaling cycle do not switch off the machine If the machine has been switched off it will continue the descaling from the point at which it was interrupted the next time it is turned on To execute the descaling cycle follow the steps below Before descaling E Empty the drip tray and the coffe
17. E Press the button to stop brewing ENGLISH 29 fi For storage you can put the suction tube as shown in the picture al Note After having pressed the amp button it will take a few seconds before the machine stops dispensing steam completely BEB caution After frothing the milk a small quantity of hot water must be dis pensed into a container See chapter Daily cleaning of the Automatic Milk Frother for detailed cleaning instructions Ji Note After frothing the milk it is possible to brew an espresso or dispense hot water straight after HOT WATER DISPENSING FN warning Danger of scalding Dispensing may be preceded by small jets of hot water The Automatic Milk Frother may reach high temperatures Never touch it with bare hands Use the appropriate protective handle only Before dispensing hot water make sure that the machine is ready to use and the water tank is filled E Place a container under the steam wand 30 ENGLISH STEAM HOTWATER 5 we Press the g tp button The machine shows this display ee Ell Press the button to start dispensing hot water STEAM HOTWATER COFFEE STRENGTH we o Ef The following icon is displayed during pre heating time required by the machine Cam Yellow H Pour the desired amount of hot water To stop the hot water dispens ing press the button IG r
18. ENGLISH 37 E Insert the coffee residues drawer in its seat and ensure that it is cor rectly in place Note If the coffee residues drawer is not correctly positioned the brew group may not fit into the machine Insert the brew group in its seat again until it locks into place without pressing the PUSH button EE Insert the coffee grounds drawer with the drip tray back into the ma chine and close the service door Monthly Cleaning of the Automatic Milk Frother Every month you need to perform a more thorough cleaning of the Auto PHILIPS matic Milk Frother using the Saeco Milk Circuit Cleaner The Saeco Milk Saeco n i Circuit Cleaner can be purchased separately Please refer to the mainte nance product page in this user manual for further details Milk circui WN cleaner 4 Warning Danger of scalding Dispensing may be preceded by small jets of hot water 38 ENGLISH E Make sure that the Automatic Milk Frother is correctly installed Pour the milk circuit cleaner into a container Add 17 ounces of luke warm water and wait for the product to dissolve completely EJ Insert the suction tube into the container EJ Place a large container 51 ounces under the Automatic Milk Frother STEAM HOTWATER 5 we COFFEE STRENGT H Press the g button The machine shows this display al Press the Zp button to start dispensing steam This icon is displa
19. NZA water filter if fitted in the water tank Reinsert the Automatic Milk Frother Weekly cleaning of the brew group chapter The rinse cycles are performed in order to have the circuit cleaned with a preset amount of water to ensure proper machine performance If the water tank is not filled up to MAX level the machine might require three or more cycles ENGLISH 51 PROGRAMMING It is possible to customise the machine s functions via the programming menu The following settings can be adjusted TALC CLEAN Yellow Yellow Yellow Yellow Yellow Coffee temperature This function adjusts the coffee brewing temperature Timer stand by This function adjusts the time taken for the machine to go into stand by mode after the last brewing Contrast This function adjusts the contrast of the display to better view the mes sages Water hardness This function adjusts the water hardness setting according to the area where you live 1 very soft water 2 soft water 3 hard water 4 very hard water For more details please see the Measuring and Programming Water Hard ness chapter INTENZA Water Filter This function manages the INTENZA water filter For more details see the chapter about filter handling Descaling cycle This function activates the descaling cycle 52 ENGLISH ESC Factory setti
20. PECIFICATIONS The manufacturer reserves the right to make changes to the technical specifications of the product Nominal Voltage Power See label on the inside of the service door Rating Power Supply Housing material Thermoplastic material Size w x hx d 215 x 330 x 429 mm 8 5 x 13 x 16 9 inches Weight 7 2 kg 16 pounds Power cord length 800 1200 mm 32 47 inches Control panel Front panel Automatic Milk Frother Special for cappuccino Cup sizes up to 178mm 7 inches Water Tank 1 8 liters Removable type Coffee bean hopper 250 g 1 cup capacity Coffee grounds drawer 15 capacity Pump pressure 15 bar Boiler Stainless steel type Safety devices Thermal fuse WARRANTY AND SERVICE Warranty For detailed information on your warranty and related conditions please read the warranty booklet supplied separately Service We want to ensure that you remain satisfied with your machine If you have not already done so please register your purchase at www philips com welcome This will enable us to stay in contact with you and send you cleaning and descaling reminders If you need service or support please visit the Philips website at www philips com support or contact the Philips Saeco hotline in your country The contact details can be found in the warranty booklet supplied separately or on www philips com support 62 ENGLISH ORDERING MAINTENANCE PRODUCTS Fo
21. Pre Ground Coffee This function allows you to use pre ground coffee With the pre ground coffee function you can only brew one beverage at a time EE Push the lever downwards to select the ESPRESSO function Press the button until the display shows the icon for pre ground coffee Green EJ Lift the pre ground coffee compartment lid and add one scoop of pre ground coffee to the compartment Use only the measuring scoop supplied with the machine Then close the pre ground coffee compartment lid PN warning Add only pre ground coffee to the pre ground coffee compartment Other substances and objects may cause severe damage to the ma chine Such damage will not be covered by warranty 24 ENGLISH El Press the 9 button to brew an espresso The brewing cycle starts E After the prebrewing cycle the beverage begins to pour out of the dispensing spout EJ Brewing automatically stops when the preset level is reached press the S button to stop it earlier After brewing the machine returns to the main menu Repeat the steps described above to brew more espressos using pre ground coffee Note If no pre ground coffee is poured into the pre ground coffee compart ment only water will be dispensed If the dose is excessive and 2 or more scoops of pre ground coffee are used the machine will not brew the product and any ground coffee will be discharged into the coffee gr
22. accurate and perfect grinding and coarseness for every coffee speciality This technology provides for full aroma preservation delivering the truly Italian taste in every cup PN warning The ceramic coffee grinder contains moving parts that may be danger ous Do not insert fingers or other objects Only adjust the ceramic coffee grinder using the grinder adjustment key The grinders can be set to adjust the grinding to your personal taste ENGLISH 17 El Press and turn the grinder adjustment knob below the coffee bean hopper one notch at a time Use the coffee grinder adjustment key provided with the machine You will taste the difference after brewing 2 3 cups of coffee EA The reference marks inside the coffee bean hopper indicate the grind setting There are 5 different grind settings to choose from position 1 for coarse grind milder taste to position 2 for fine grind stronger taste Adjusting the Aroma Beverage Strength Choose your favorite coffee blend and adjust the amount of coffee to be ground according to your personal taste You can also select the pre ground coffee function I Note Selection must be made prior to selecting the desired beverage Five choices are possible by pressing the 4 button Each time the button is pressed the aroma changes by one degree according to the selected amount 2OO extra mild aroma O2O D mild aroma MULO medium aroma MVL strong aroma 000
23. all white filter or the INTENZA water filter if in stalled from the water tank and wash it with fresh water Put the small white filter or the INTENZA water filter if installed back in its housing by gently pressing and turning it at the same time EEJ Fill the water tank with fresh water g STEAM HOTWATER wv COFFEE STRENGT Red ENGLISH 33 Daily Cleaning of the Automatic Milk Frother For hygienic reasons and to ensure a perfect milk froth consistency it is important that the Automatic Milk Frother be cleaned after each use DN warning Danger of scalding Dispensing may be preceded by small jets of hot water After each milk frothing you always need to El Plunge the suction tube into a container filled with fresh water Place an empty container under the Automatic Milk Frother 34 ENGLISH 4 Press the Zp button to start dispensing steam H This icon is displayed during pre heating time required by the ma e chine Ca Yellow Fal The following icon will be displayed during the dispensing phase Dispense water from the Automatic Milk Frother until clear water flows out Press the amp button to stop dispensing Green Clean the suction tube with a damp cloth Weekly Cleaning of the Machine El Clean the seat of the drip tray Clean the pre ground coffee compartment with the cleaning brus
24. as described in the previous chap E ter L f F Press the E button and scroll the pages by pressing the E button 6 until the following icon is displayed v gt EJ Select the RESET option Press the E button to confirm ON z OFF pRESEM g EJ To exit press the tp button The machine shows this display and is ready to brew Green The machine is now programmed to manage a new INTENZA water filter inal Note If the INTENZA water filter is already installed and you want to remove but not replace it select the OFF option instead Yellow If there is no INTENZA water filter installed insert the small white filter previously removed back into the water tank 16 ENGLISH ADJUSTMENTS The machine allows for certain adjustments so that you can brew the best tasting coffee possible Saeco Adapting System Coffee is a natural product and its characteristics may change according to its origin blend and roast The machine is equipped with a self adjusting system that allows the use of all types of coffee beans available on the market except for flavored coffee beans The machine automatically adjusts itself after brewing several cups of coffee to optimize the extraction of the coffee to the compactness of the ground coffee Adjusting the Ceramic Coffee Grinder Ceramic coffee grinders always guarantee
25. ckaging immerse it ver tically with the opening positioned upwards in cold water and gently press the sides so as to let the air bubbles out 14 ENGLISH EJ Set the INTENZA water filter according to the measurements per formed see previous chapter and indicated on the base of the filter A soft water equals 1 or 2 on the test strip B hard water standard equals 3 on the test strip C very hard water equals 4 on the test strip EJ Put the INTENZA water filter into the empty water tank Press it down until it cannot move any further EJ Fill the water tank with fresh water and reinsert it into the machine Fl Dispense all the water of the tank by using the hot water function see Hot Water Dispensing chapter Fill the water tank again EJ Press the E button and scroll the pages by pressing the button 3 until the following display is shown YZ EJ Press the button to select ON and press the button to con firm V GI To exit press the tp button The machine shows this display and is ready to brew Green The machine has been programmed to inform the user when to replace the INTENZA water filter ENGLISH 15 Replacing the INTENZA Water Filter When the INTENZA water filter needs to be replaced with a new one the following icon is displayed EE Replace the INTENZA water filter
26. e 8 ENGLISH EP switch the power button to I to turn on the machine The I button flashes EE To turn on the machine simply press the I button The control panel indicates that the circuit must be primed ow Yellow USING THE MACHINE FOR THE FIRST TIME When using the machine for the first time the following activities need to happen 1 You need to prime the circuit 2 The machine will perform an automatic rinse self cleaning cycle 3 You need to initiate a manual rinse cycle Circuit Primin During this process fresh water flows through the internal circuit of the machine and the machine warms up This takes a few minutes E Place a container under the steam wand START Yellow Yellow Yellow Yellow Green ENGLISH 9 Press the button to start the cycle The machine starts the auto matic priming of the circuit by dispensing some water through the steam wand EJ The bar under the icon shows the operation progress When the pro cess is completed the machine stops dispensing automatically EJ Then the control panel shows the machine warm up icon Automatic Rinse Self Cleaning Cycle When warm up is complete the machine automatically performs a rinse self cleaning cycle of the internal circuit with fresh water This takes less than a
27. e ground coffee to the compartment E Push the lever downwards to select the ESPRESSO function al Press the button to start the brewing cycle Wait until the machine has dispensed half a cup of water EJ switch the power button on the back of the machine to 0 E Let the solution take effect for about 15 minutes Make sure you dis card the dispensed water E Switch the power button on the back of the machine to I To turn on the machine press the Y button Wait until the end of the automatic rinse cycle EE Remove the drip tray and the coffee grounds drawer and open the service door Remove the brew group 46 ENGLISH Wash the brew group thoroughly with fresh water EE After rinsing the brew group insert it again in its seat until it locks into place see Weekly Cleaning of the Brew Group chapter Insert the drip tray and the coffee grounds drawer Close the service door IE Press the button to select the pre ground coffee function without adding pre ground coffee to the compartment C Green HE Press the button to start the brewing cycle Gd Repeat steps 14 to 15 twice Make sure you discard the dispensed water To clean the drip tray place Coffee Oil Remover tablet inside and fill it 2 3rds full with hot water Let the cleaning solution take effect for about 30 minutes then rinse thoroughly Monthly Cleaning of the Coffee Bean Hopper
28. e grounds drawer 48 ENGLISH Remove the Automatic Milk Frother from the steam hot water wand EJ Remove the INTENZA water filter from the water tank if it was in stalled and replace it with the small white original one Place the water tank back into the machine EJ Press the button until the following display is shown 2 T H Press the button to start the descaling process CALCCLEAN P a 2 DN 3 Note 7 T If you press the button by mistake press the g p button to quit gL you p y p WP q Fal Remove the water tank and pour in the entire contents of the descal ing solution Then top up the tank with fresh water up to the calc clean level Place the water tank back into the machine EJ Place a large container 1 5 I under both the steam hot water wand and the dispensing spout ENGLISH 49 sC E Press the EN button to start the descaling cycle ay 7 v START a E The machine will start dispensing the descaling solution at regular 3 intervals The bar on the control panel shows the cycle progress v w Note The descaling cycle may be paused by pressing the button To resume z the cycle press the button again This allows you to empty the container or to stay away from the machine for a brief period of time S EE When this icon is displayed the water tank is empty me v
29. e packaging Roget FJ For best use it is recommended to Choose a safe level surface where there will be no danger of over turning the machine or being injured e Choose a location that is sufficiently well lit clean and near an eas 6inches ily reachable socket Allow for a minimum distance from the sides of the machine as 4 a shown in the illustration Ja mm _ 6 inches EJ Remove the water tank lid E Lift the water tank using the handle ENGLISH 7 E Rinse the water tank with fresh water KA Fill the water tank with fresh water up to the MAX level and reinsert it into the machine Make sure it is fully inserted BEB caution Never fill the water tank with warm hot sparkling water or any other liquid as this may cause damage to the water tank and the machine Remove the coffee bean hopper lid EJ Slowly pour the coffee beans into the coffee bean hopper Note Do not pour too many coffee beans into the coffee bean hopper as this will reduce the grinding performance of the machine Ei caution Only coffee beans must be put into the coffee bean hopper Ground coffee instant coffee flavored coffee or any other object may damage the machine EJ Put back the coffee bean hopper lid on the coffee bean hopper E Insert the plug into the socket located on the back of the machine EK Insert the plug at the other end of the power cord into a wall socket with suitable power voltag
30. ffee compartment lid and add one measuring scoop of pre ground coffee to the compartment Use only the measur ing scoop supplied with the machine Then close the pre ground coffee compartment lid PN warning Add only pre ground coffee to the pre ground coffee compartment Other substances and objects may cause severe damage to the ma chine Such damage will not be covered by warranty 4 Press the Zp button for a medium coffee or the E button for a long coffee The brewing cycle starts E After the prebrewing cycle coffee begins to pour out of the dispensing spout Al Coffee brewing automatically stops when the preset level is reached press the button to stop it earlier After brewing the machine returns to the main menu Repeat the steps described above to brew more coffees using pre ground coffee ian Note If no pre ground coffee is poured into the pre ground coffee compart ment only water will be dispensed If more scoops have been added the machine will not brew the product and the ground coffee in the compartment will be discharged into the cof fee grounds drawer ENGLISH 27 DISPENSING STEAM CAPPUCCINO BREWING PN warning Danger of scalding Dispensing may be preceded by small jets of hot water The Automatic Milk Frother may reach high temperatures Never touch it with bare hands Use the appropriate protective handle only E Fil 1 3 of a container with cold milk tall Note
31. h EJ Remove the lower part of the dispensing spout and wash it with luke warm water ENGLISH 35 Weekly Cleaning of the Brew Grou The brew group should be cleaned every time the coffee bean hopper is filled or at least once a week E Turn off the machine by pressing the ly button and unplug the power cord Remove the drip tray and coffee grounds drawer Only at this time open the service door EJ To remove the brew group press the PUSH button pulling it by the handle and pull it out horizontally without turning it EJ Remove the coffee residues drawer and wash it thoroughly 36 ENGLISH E Thoroughly wash the brew group with fresh lukewarm water and care fully clean the upper filter Eg Caution Do not use detergent or soap to clean the brew group K Let the brew group air dry thoroughly Thoroughly clean the inside of the machine using a soft dampened cloth EJ Make sure the brew group is in the rest position the two reference signs must match If they do no match up proceed as described in steps 9 10 E Gently pull down the lever until it is in contact with the brew group base and the two reference signs on the side of the brew group match E Make sure the hook to lock the brew group is in the correct position by firmly pressing the PUSH button until it locks into place Check if the hook is at the top end position If it is not please try again
32. l button El Note If an espresso coffee is selected with the lever in the wrong position the following icon will be displayed reminding you to set the lever to the cor rect position FA Push the lever upwards to select the COFFEE function In this position you can brew a medium or long coffee by pressing the EP button or the ye button E Note If a COFFEE product is selected with the lever in the wrong position the following icon will be displayed reminding you to set the lever to the cor rect position ENGLISH 21 Adjusting the Beverage Cup Length The machine allows you to adjust the amount of brewed coffee according to your taste and the size of your cups Each time the 2p or Ef button is pressed the machine brews a pre set amount of beverage Each button may be individually programmed for a specific brew setting The following procedure describes how to program the S button El Place a cup under the dispensing spout Check the position of the selection lever EJ Press and hold the button until the MEMO icon appears on the display then release the button The machine has now entered programming mode The machine starts brewing coffee Green EJ Press the button as soon as the desired amount of coffee is reached Green Now the t button is programmed each time it is pressed the machine will brew the same amoun
33. ngs This function allows you to reset all factory values ro RA Yellow d How to Program the Machine In this example it is shown how to program the display contrast Proceed in the same way to program the other functions The programming menu can only be accessed when the machine is on and shows this display Green EE Press the E button to access programming E The main screen will be displayed Yellow EJ Press the l button to scroll the pages until the display contrast func tion is displayed Yellow ENGLISH 53 EJ Press the 5 and g buttons to increase or decrease the value of the function i Ss E When the display value is changed the OK message appears Press the button to confirm the change KA Press the g tp button to exit the programming menu STEAM HOT WATER g Note The machine automatically exits programming mode if no button is pressed for 3 minutes The values that have been changed but not confirmed won t be saved 54 ENGLISH MEANING OF THE DISPLAY ICONS This machine is equipped with a color coded system to make the user s understanding of the display signals easier The icons are color coded according to the traffic light principle Ready Signals Green Color The machine is
34. ounds drawer BREWING A COFFEE Before brewing coffee make sure that there are no warnings shown on the control panel and that the water tank and coffee bean hopper are filled Brewing a Coffee Using Coffee Beans E Place 1 MUG or 1 TUMBLER under the dispensing spout Note Refer to section Adjusting the Dispensing Spout for the Tumbler posi tioning Green Green ENGLISH 25 Push the lever upwards to select the COFFEE function EJ To brew a beverage press the 8 button to select the desired aroma EJ To brew a medium coffee press the Zp button once This icon will be displayed E To brew a long coffee press the av button once This icon will be displayed Note In this operating mode the machine automatically grinds and doses the correct amount of coffee ay After the prebrewing cycle the beverage begins to pour out of the dispensing spout Beverage brewing automatically stops when the preset level is reached press the gt button to stop it earlier Brewing a coffee Using Pre Ground Coffee This function allows you to use pre ground coffee With the pre ground coffee function you can only brew one beverage at a time E Push the lever upwards to select the COFFEE function 26 ENGLISH Green Press the button to select the pre ground coffee function a EJ Lift the pre ground co
35. r cleaning and descaling use Saeco maintenance products only You can purchase these at the Philips online shop at www shop philips com service your local dealer or at authorised service centres If you have any difficulties obtaining maintenance products for your ma chine please contact the Philips Saeco hotline in your country The contact details can be found in the warranty booklet supplied sepa rately or on www philips com support Overview of maintenance products 2 PHILIPS Descaling solution CA6700 PHILIPS _INTENZA Water filter cartridge CA6702 Grease HD5061 Coffee Oil Remover CA6704 Milk Circuit Cleaner CA6705 Maintenance Kit CA 6706 ENGLISH 63 PHILIPS The manufacturer reserves the right to make changes without prior notice www philips com welcome 421944010581 Rev 0O del 15 06 13
36. rd is used 1 The marked electrical rating of the detachable power supply cord or extension cord should be at least as great as the electrical rating of the appliance 2 If the appliance is of the grounded type the extension cord should be a grounding type 3 wire cord and 3 The longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over Congratulations on your purchase of a Saeco Minuto Auto matic Milk Frother full automatic coffee machine To fully benefit from the support that Saeco offers please register your product at www philips com welcome This user manual applies to HD8772 The machine is made for preparing espresso and coffee using whole coffee beans and for dispensing steam and hot water In this user manual you will find all the information you need to install use clean and descale your machine ENGLISH 3 CONTENTS INSTALLATION w4 Product Overview we General Description wed PREPARING FOR USE 6 Machine Packaging Machine Installation USING THE MACHINE FOR THE FIRST TIME Circuit Priming Automatic Rinse Self Cleaning Cycle Manual Rinse Cycle sssssscccccseeesenes Measuring and Programming Water Hardness INTENZA Water Filter Installation Replacing the INTENZA Water Filter ADJUSTMENTS Saeco Adapting System Adjusting the Ceramic Coffee Grinder Adjusting the
37. s chapter summarizes the most common problems you could encoun ter with your machine If you are unable to solve the problem with the information below visit www philips com support for a list of frequently asked questions or contact the Philips Saeco hotline in your country The contact details can be found in the warranty booklet supplied sepa rately or on www philips com support Machine actions Causes Solutions The machine does not switch The machine is not connected to Connect the machine to the electric on the electric network or the power network and turn the power button button is in the O position to the l position The drip tray gets filled al Sometimes water is drained auto This is seen as normal machine though no water is drained matically by the machine into the behavior drip tray to manage the rinsing of the circuits and ensure optimum machine performance The red x icon is always The coffee grounds drawer was The coffee grounds drawer must displayed on the machine emptied with the machine off always be emptied with the machine on Wait until the icon is dis played before refitting the drawer The espresso is not hot The cups are cold Preheat the cups with hot water enough No hot water or steam is The hole of the hot water steam Clean the hole of the steam wand dispensed wand is clogged using a pin Make sure that the machine is off and has cooled down before performing this operation
38. sh water and let it dry as described in the Weekly Cleaning of the Brew Group chapter E Apply the grease evenly on both side guides Also lubricate the shaft 44 ENGLISH pHILIPS Saeco EJ Insert the brew group in its seat until it locks into place see Weekly Cleaning of the Brew Group chapter E Close the service door and insert the drip tray and coffee grounds drawer Monthly Cleaning of the Brew Group with Coffee Oil Remover Besides weekly cleaning we recommend running the cleaning cycle with Coffee Oil Remover after approximately 500 cups of coffee or once a month This operation completes the maintenance process for the brew group You can purchase separately the Coffee Oil Remover For further details please refer to the maintenance products page in this manual 1 caution The Coffee Oil Remover tablets are to be used for cleaning only and do not have a descaling function For the descaling procedure use the Saeco descaling solution and follow the procedure described in the Descaling chapter El Place a container under the dispensing spout Make sure the water tank is filled with fresh water up to the MAX level Green ENGLISH 45 EJ Put a Coffee Oil Remover tablet in the pre ground coffee compart ment EJ Press the ey button to select the pre ground coffee function without adding pr
39. t of espresso that was just programmed Note To program the other two EP or beverages the same steps should be followed You should always use the S button to stop brewing coffee when the desired amount of coffee is reached even when you are programming the other two ror beverages 22 ENGLISH BREWING AN ESPRESSO Green Green Before brewing an espresso coffee make sure that there are no warnings shown on the control panel and that the water tank and coffee bean hop per are filled Brewing an Espresso using Coffee Beans E Place 1 or 2 cups under the dispensing spout EA Push the lever downwards to select the ESPRESSO function E To brew an espresso press the button to select the desired aroma i EZ To brew an espresso press the button once This icon will be displayed H To brew two espressos press the button twice consecutively This icon will be displayed f Note In this operating mode the machine automatically grinds and doses the correct amount of coffee Brewing two espressos requires two grinding and brewing cycles automatically carried out by the machine ENGLISH 23 al After the prebrewing cycle the beverage begins to pour out of the dispensing spout Espresso brewing automatically stops when the preset level is reached press the button to stop it earlier Brewing an Espresso using
40. ton and then the button EJ Fill the water tank again up to the MAX level Now the machine is ready for coffee brewing The display to the left will be shown be Note When the machine has not been operated for at least two weeks it will automatically perform a start up rinse self cleaning cycle Following this you need to initiate a manual rinse cycle as described above The automatic rinse self cleaning cycle starts automatically when the ma chine has been in stand by mode or switched off for more than 15 minutes At the end of the cycle it is possible to brew a coffee 12 ENGLISH Intenza Aroma System Machine Water Hardness Setting Yellow Measuring and Programming Water Hardness Water hardness measuring is very important in order to define the descal ing frequency and to install the INTENZA water filter for more detail on the water filter see next chapter To measure the water hardness follow the steps below EE Immerse the water hardness test strip supplied with the machine in water for 1 second Note The test strip can only be used for one single measurement FJ Wait for one minute EJ Check how many squares have changed to the color red and then refer to the table im Note The numbers on the water hardness test strip correspond to the water hardness adjustment settings More precisely 1 1 very soft water 2 2 soft water 3 3 hard water
41. wall outlet 12 Do not use appliance for other than intended use 13 Save these instructions SAVE THESE INSTRUCTIONS CAUTION This appliance is for household use only Any servicing other than cleaning and user maintenance should be performed by an authorized service center Do not immerse machine in water To reduce the risk of fire or electric shock do not disassemble the machine There are no parts inside the machine serviceable by the user Repair should be done by authorized service personnel only 1 Check voltage to be sure that the voltage indicated on the nameplate corresponds with your voltage Never use warm or hot water to fill the water tank Use cold water only Keep your hands and the cord away from hot parts of the appliance during operation Never clean with scrubbing powders or harsh cleaners Simply use a soft cloth dampened with water For optimal taste of your coffee use purified or bottled water Periodic descaling is still recommended every 2 3 months Do not use caramelized or flavored coffee beans INSTRUCTIONS FOR THE POWER SUPPLY CORD A short power supply cord or detachable power supply cord is to be provided to reduce risks resulting from becoming entangled in or tripping over a longer cord Longer detachable power supply cords or extension cords are available and may used if care is exercised in their use Ifa long detachable power supply cord or extension co
42. yed during pre heating time required by the ma Ca Yellow chine STOP Green ENGLISH 39 EJ The following icon will be displayed during dispensing When the solution has been completely dispensed press the button to stop dispensing Note Steam dispensing automatically stops after a continued use of 3 minutes Press the of we button then the EP button to start dispensing steam again PN warning Never drink the solution dispensed during this step E Rinse the container thoroughly and fill it with 17 ounces of fresh water to be used for the rinse cycle GM Insert the suction tube into the container EE Empty the container and place it back under the Automatic Milk Frother 40 ENGLISH STEAM HOT WATER 5 we STOP Yellow Green IA Press the of ep button The machine shows this display EE Press the Ep button to start dispensing steam EE This icon is displayed during pre heating time required by the ma chine IE The following icon will be displayed during dispensing When the solution has been completely dispensed press the button to stop dispensing Es Note Steam dispensing stops after 3 minutes Press the ef ey button then the Ep button to start dispensing steam again fq Wash all the Automatic Milk Frother components by following the instructions below Remove the
Download Pdf Manuals
Related Search