Manual - nke marine electronics
Contents
1. Exit the setting menu by maintaining pressure on Ent key or wait 10s until the SL50 exits automatically the menu The new setting is saved in memory and is applied to all SL50 of your installation 1 9 Choice of the unit You have the option to choose the display units of the channels in knots or in km hr for the log speedometer in knots or m s for the anemometer in degree Fahrenheit or in degree Celsius for the temperature in meters or in feet for the depth finder Unit setting procedure Using keys O and a select the channel from which you wish to change the unit Press Ent key until the sub channel Unit appears Using keys O and o select the unit and press Ent to validate Exit the setting menu by maintaining pressure on the Ent key or wait 10s until the SL50 exits automatically the menu The new setting is saved in memory 10 SL50 User guide 33 60 022 000 1 10 Choice of languages You can configure the SL50 in one of these six available languages French English Italian Spanish German and Dutch Using the keys Q and o select the CONFIG channel Press Ent key until the list of Sub channels valid alarm language and lighting appears Successively press Ent key to select the chosen language Press Ent to validate Exit the setting menu by maintaining pressure on Ent or wait 10s until the SL50 automatically exit the menu The new setting is saved in memory 1 11 Zero setting of the2. cul ee cudgel dates 15 1 18 SL50 INITIALISATION SEE CHAPTER ZB 2 era ee sen nee 15 INSTALLATION iii 16 2 PACKING UST ee re a Rh a A A ER ALAS sah 16 2 2 LIST OR ACCESSORIES Eis ae ae se ee ae esse 16 2 3 INSTALLATION PRECAUTIONS de oles ee 16 2 4 MOUNTING ON MAST FOOT SUPPORT ccccceccceceseecececeeeeceueceueceeeueeeeeueeeeeuseueeeueeesaeeeueeeueeseaess 17 2 5 WALL MOUNTING 22223 cist Rely Si ele aan te 17 2 6 CONNECTION TO THE TOPLINE BUS c cccccccceeccccecccccucceecuccesuueceeuuecesuuuceuaueeeuaueeeuaueeeuaeeeeuaeeeaes 19 2 7 IDENTIFICATION OF THE CABLE WIRES ccccceccceeccceccceceeceeececcceceeceeeueeeceueeceeeeeeeueueeseeseeueuees 19 2 8 SL50 AND REMOTE CONTROL INITIALISATION cccoocccccnccccnnnccnnnnccnnnacononanonnnancnnnaccnnnancnnnaccnnanans 20 2 SL50 User guide 33 60 022 000 1 USING 1 1 Presentation The Multifunction SL50 is a display from the TOPLINE range Its screen with high definition LCD technology offer excellent readability and a wide angle of view of the data displayed whether by daylight or at night It is connected to the TOPLINE bus of your installation and displays all the channels available on the bus se so Channel or sub aa a nr a channel designation So e e 17 BK y Go A VANE VANE WANE WAN Data value O nke The SL50 is controlled using either a cable remote control or a radio rem
3. the message 3000 is indicated For the previous generation of compass referenced as 90 60 005 at least three circles must be executed In case of problem during autocompensation the SL50 displays the PAN message plus one code Code 1 cancellation at user request Code 2 detection of a gyration in the opposite direction Start again clockwise Code 3 excessive variation between 2 heading measurements Reduce the speed of your boat to 2 or 3 knots Code 4 angle correction higher than 20 Start the autocompensation procedure over In case of autocompensation error the measurements are not saved to the memory and the sensor resumes its normal operating mode 2 4 Technical specifications Power supply 10 to 16VDC Consumption 20mA without lighting and 70mA with lighting Tightness IP67 Weight 1 150kg including cable Dimensions height 260mm width 156mm thickness 45mm Operating temperature 10 C to 50 C Storage temperature 20 C to 60 C Horizontal viewing angle superior to 120 Vertical viewing angle superior to 90 Height of the characters displayed 50 mm for the channel and 10 mm for the identifier and the unit 14 SL50 User guide 33 60 022 000 2 5 Version and address number of the display You can check the software version of the display and its address in the list In order to do that select the CONFIGURATION channel then press the Ent key for
4. 5 Clean the mounting surface with alcohol introduce the cable in the 18 drilled hole position the SL50 so that it faces the four 4 holes place the four screws provided with the product in the holes from the back of the partition tighten the four fixing screws moderately CAUTION When mounting the SL50 tighten the fixing screws moderately Excessive tightening can cause the casing to break Do not use glue putty to mount the SL50 3 5 Wall mounting Make sure the location is clean smooth and flat Check that there is sufficient space behind the partition to make the cable run Procedure Perform the drillings of figure 13 on the partition Clean the mounting surface with alcohol Lay a very thin silicone sealing joint around the mounting perimeter introduce the cable in the 18 drilled hole position the SL50 so that it faces the four 5 holes place the four screws provided with the product in the holes from the back of the partition tighten the four fixing screws moderately 17 SL50 User guide 33 60 022 000 Figure 5 18 SL50 User guide 33 60 022 000 3 6 Connection to the Topline bus 1 Make the bus cable run from the SL50 to the TOPLINE terminal box of your installation 2 Connect the bus cable inside the terminal box VITES SURF 16 85 supply 12Vdc O ae init wire red GND
5. Using the keys Y A change the new calibration coefficient to 1 1 nke CALIB COEF Then successively press Ent select the sub channel CALIB COEF nke 5150 mem Press Ent validate and exit by maintaining pressure on Ent 16 85 The calibration is saved in memory c nke amp Figure 4 CAUTION The calib coef parameter is a multiplier coefficient This value must never be equal to zero By default this coefficient is set to 1 00 If it is not the case before starting a calibration enter the value 1 00 2 2 Offset setting procedure Follow the above procedure and choose the OFFSET sub channel Note that this value is set to 0 13 SL50 User guide 33 60 022 000 2 3 Autocompensation of the fluxgate compass Please refer to the compass user manual before starting the autocompensation procedure In order to achieve a successful autocompensation you must navigate On smooth sea with no current and no wind Away from large magnetic masses such as cargo boats In an open area allowing the execution of a circle with a diameter approximately 5 times the length of the boat Ata constant speed of about 2 or 3 knots Procedure 1 Select the magn head channel 2 Start to describe the circle then press the 2 second on the key VW to launch the autocompensation procedure 3 One single circle is sufficient to perform the autocompensation correctly when its a success
6. daily log The channels daily log and total log are at your disposal on your display You will use the daily log to count the number of nautical miles completed during a sailing leg The value is kept in memory when the power supply of your installation is cut off Resetting the daily log channel to zero will allow you to count the number of nautical miles of the following sailing leg Zero setting procedure of the daily log using the keys Q and o select the channel daily log Press until the log is set to 0 The total log indicates the number of nautical miles completed since the installation of your depth finder log interface Only a complete initialisation of your depth finder log interface allows to reset the total log to zero It is performed by initialising the surface speed channel 11 SL50 User guide 33 60 022 000 1 12 Use of the chronometer The display includes a regatta chronometer Times by default are T1 6min and T2 4min 1 12 1 Starting the chronometer Using the keys and O select the CHRONOMETER channel Press until the SL50 displays 6 00 The chronometer is ready Press En to start the chronometer then the SL50 displays GO During countdown the last 5 seconds are signalled by a BEEP then the START signal is given by the alarm Note that if you did not start the chronometer exactly at the start signal you can synchronise the chronometer countdown at T2 by pressing the Ent key D
7. does not display the NMEA data that from the GPS Has the NMEA link been initialised see chapter 16 for example Pane The NMEA link is not or is badly connected to the terminal box check the connection of the SL50 and that of the NMEA transmitter GPS Your display indicates battery fault Check the voltage of your battery with a voltmeter the operating voltage must be higher than 10VDC Check the charge behaviour of your battery If you do not manage to solve the problem please contact your distributor 2 7 SL50 initialisation see chapter 4 8 15 SL50 User guide 33 60 022 000 3 INSTALLATION This chapter describes the installation and the initialization of the SL50 IMPORTANT Read this user guide entirely before starting the installation Any electrical connection of the SL50 on the TOPLINE bus must be carried out with the terminal box 90 60 417 equipped with a connection terminal for the NMEA input Only use TOPLINE bus cable of the type 20 61 001 Any intervention on the TOPLINE bus must be carried out with the installation power switched off 3 1 Packing list one Multifunction SL50 equipped with ten meters of cable including the TOPLINE bus and one NMEA input one user guide one protective cover four M4 fixing screws 3 2 List of accessories Standard terminal box TOPLINE bus 90 60 121 Terminal box TOPLINE bus with NMEA input 90 60 417 Cable remote control 90 60 245 Wi
8. will be displayed To disable the Man Over Board alarm you must cut off the power supply of your TOPLINE installation CAUTION the calculation of the estimate for the Man Over Board function does not take into account the drift of the boat caused by the current and the wind For more detailed information please refer to the remote control user guide key This key is useless for the Multifunction SL50 6 SL50 User guide 33 60 022 000 1 4 Channel selection Using the remote control configure the display according to your requirements Examples of configuration suso O O s 50 BOAT SPEED nke Procedure Using the keys Wand a you can select in the list the channel you wish to display The new channel to display is recorded CAUTION if your installation is equipped with several TOPLINE displays make sure that the remote control controls the display which you wish to operate Press the o key repeatedly until the intended display blinks 1 5 What is a sub channel The sub channels are made to modify setting and display parameters of the channels For example the sub channels of the surface speed channel are the offset and the calibration coefficient setting parameters of the log speedometer sensor the measurement unit in knots or in km hr the filter setting the setting of the upper alarm and the lower alarm The same applie
9. 5 seconds The date time and version of the SL50 software are then momentarily displayed on the screen To check what the version of your software is select the CONFIG channel and press Ent key until nke SL50 is displayed The date time and version of the SL50 software are then momentarily displayed on the screen To read the address number select the CONFIG channel and press the key A for 3 seconds 2 6 Diagnostic for 1 level troubleshooting Before contacting technical support please check the troubleshooting table below Problem Possible causes and solutions The bus cable is not or is badly connected to the terminal box check the The Topline installation does not detect the SL50 plugging and the connection inside the terminal box Check the state of the cables they must not show any sign of wear or cut The remote control does not control the SL50 The address of the remote control is lower than that of the SL50 reinitialise the remote control see chapter 17 The SL5O0 is set at the address 0 perform its initialisation see chapter 17 The SL50 displays the message data wire error Check that the black data wire is connected at the right location in the terminal box see chapter 17 The SL50 displays the message collision error It is possible that there are two master displays at address 1 on your installation check the addresses if it is the case reinitialise one of the displays The SL50
10. DATA black 12VDC white boite de connexion 0 60 121 Figure 6 connection to TOPLINE bus If you reduce the length of the bus cable strip and galvanise the wires before connecting them inside the terminal box 3 7 Identification of the cable wires White cable 6 wires Wire identification TOPLINE Bus initialisation wire GND 19 SL50 User guide 33 60 022 000 3 8 SL50 and remote control initialisation At first power up you must initialise the SL50 so that an address is assigned to it The display is delivered with the address set as 0 During the initialisation it will automatically insert itself in the list of instruments and displays of the TOPLINE bus of your installation either as master at the address 1 if this address is available on the bus or as slave if the address 1 is taken by a master at an available address comprised between 2 and 20 Likewise the remote controls must also be initialised Please refer to the remote control user guide 3 8 1 Initialisation procedure the SL50 is set at the address 0 your installation is powered off disconnect the initialisation red wire from the init terminal GND power up your installation the SL50 then performs an auto test when the message connect the red wire appears reconnect the red
11. Multifunction SL50 and its remote control Product reference 90 60 445 white 90 60 472 carbon USER GUIDE and INSTALLATION GUIDE nke Sailing competition Z I Kerandr Rue Gutenberg 56700 HENNEBONT FRANCE http www nke fr N indigo 0 892 680 656 0 34 min TABLE OF CONTENT USIN e rara cudnasasdueatdascniseu scvecadundvdatvuadvadeverdvanaduscvasaveswvacavaneuats 3 II PRESENTATION iodo tiro neuerer 3 LIST OF CHANNELS CREATE Ute FRE a Tao 5 1 3 KEYPAD FUNCTIONS OF THE REMOTE CONTROL cccccecccecsceesececeuecsceuseeuseeeceeeuseeuseueeeeeueeaneeuees 6 Tee GIANNIS EEC TION Ga De lose cent Cet ido te boat de 7 t5 WHAT ISA SUBO HAN NEL SN a a A a a 7 TO ALARMS SETTING 0 de arena anne ne A er Nat E 8 1 7 FILTERING OF THE CHANNELS uaeeennunennnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nen 9 1 8 WEIGHTING SE MING ss 225 een are 10 eS AS ONCE OF THE UNT dd is Dad Sat So Rie tates 10 1 10 CALIBRATION OF SENSOR St 2222 A A AE A A SO 13 1 11 AUTOCOMPENSATION OF THE FLUXGATE COMPASS cccccccccececeeseeceeeeceuessenseueeeeaeeeuneeneeees 14 1 12 ZERO SETTING OF THE DAILY LOG codi A di 11 1135 CHOICE OF LANGUAGES ca ee ee ee cask 10 1 14 USE OP THE CHRONO M T R iii 12 1 15 TECHNICAL SPECIFICATIONS na nannten 14 1 16 VERSION AND ADDRESS NUMBER OF THE DISPLAY c cccccecececeececeueceeeesseeseueceeeeesunseueeeeaeees 15 1 17 DIAGNOSTIC FOR 1 LEVEL TROUBLESHOOTING
12. SL50 is master By default these channels are calculated using the surface speed and in the absence of the latter it will be calculated using the bottom speed These average and maximum values are calculated from the last power up of your installation You can reset these channels to zero without switching off the bus select the channel MAX SPD and AVERAGE SPD then press the O key for 2 seconds 5 SL50 User guide 33 60 022 000 1 3 Keypad functions of the remote control O Low key and 4 High key These keys allow to select a different channel to the one already displayed They also allow to increment or decrement a data which is in the process of being modified O key The remote control also enables you to control the other displays of your TOPLINE installation the address of which is lower than the address of the remote control Press this key to select the TOPLINE display which you wish to operate End key This key allows to access the sub channels and to validate the settings you implement Brief pressure on this key also allows to set the level of lighting Man Over Board key Press this key for 5 seconds and the function Man Over Board is activated When a speedometer and a compass are connected to the TOPLINE bus the displays then automatically indicate the estimated bearing and distance to reach the man over board If your installation only comprises a speedometer then only the estimated distance
13. TERING appears nke NIZA Then successively press Ent key to select the sub channel FILTERING 5150 FILTERING i Using the keys w A set the new filtering value to 5 BOAT SPEED Validate and exit the filtering menu by maintaining pressure on Ent 1 6 8 5 The new value is saved in memory Figure 3 9 SL50 User guide 33 60 022 000 1 8 Lighting setting The SL50 as well as the other displays of the TOPLINE range have five levels of backlighting 0 no lighting 1 corresponds to the minimum level of lighting and 4 to the maximum level You have the option to set the level of lighting either on the SL50 only or on every TOPLINE display of your installation 1 8 1 SL50 setting procedure Press Ent key to enter LEVEL SETTING Using keys O and O set the lighting level from 0 to 4 After few seconds the SL50 exits automatically the menu The setting is saved in memory 1 8 2 Setting procedure for every display of your installation Follow the above procedure then press on the En key to apply the setting to every display 1 8 3 Colour setting The SL50 offers the option of a red or a green backlighting Using the keys O and o select the CONFIG channel Press Ent key to validate until the list of sub channels Valid alarm language and lighting appears Then successively press Ent key to select lighting Using keys O and a select green or red Press Entto validate
14. ote control not included with the product 3 SL50 User guide 33 60 022 000 Architecture of the installation The presence of the equipment in the following diagram is for information only and does not represent the equipment of your installation BOAT SPEED 16 85 input NMEA NMEA NMEA log depth interface 90 60 450 TOPLINE bus 20 61 001 GND DATA black 12VDC white connection box 90 60 417 gt E SS SS SS gt 8 log depth speedometre Figure 1 4 SL50 User guide 33 60 022 000 1 2 List of channels created The master display whether it is the SL50 or any other TOPLINE display and each TOPLINE sensor automatically create their respective channels when they are connected to the TOPLINE bus Channel designation Magnetic heading Apparent wind angle Apparent wind speed Depth Surface speed Channels created Maximum and average speed by the Distance and heading to man over board SL50 Configuration when set as master display Target speed NMEA Performance i Heading on other side channels displayed y Optimum wind angle Optimum VMG angle Please note that the channels MAX SPD and AVERAGE SPD can be accessed when the
15. reless remote control 90 60 258 3 3 Installation precautions The location of the SL50 must be so that the helmsman is able to easily read the data placed in a location away from potential shocks more than 40cm away from a magnetic compass more than 1 meter away from a VHF radio transmitter The best readability of the SL50 is generally obtained by mounting it on a mast foot support You can also wall mount it on any flat surface of the boat Four M4x30mm fixing screws are provided with the SL50 The support is an accessory available at your distributor 16 SL50 User guide 33 60 022 000 3 4 Mounting on mast foot support Make sure that the support you have chosen can be mounted on the mast of your boat Check that there is sufficient space behind the partition to make the cable run If the cable runs inside the mast make the cable pass through an opening equipped with a grommet If the cable runs across the deck make the cable pass through a tight stern tube gland 3 4 1 Mounting procedure for the support place the support on the mast foot using a pencil locate the six fixing holes then remove the support using acentre punch mark the centre of each hole drill the holes with a diameter 5 mount the support with the six fixing screws or six rivets not included 3 4 2 Mounting procedure of the SL50 on the support drilla 18 holes in the support as indicated on Figure
16. rm value to 20 nke BOATSPEED Validate and exit the alarm menu by maintaining pressure on Ent 1 6 8 5 The new value is saved in memory Figure 2 8 SL50 User guide 33 60 022 000 1 6 2 Alarms activation procedure After having set the alarms you can activate or disable all the alarms Using the keys Q and A salci the CONFIG channel Press Ent key until the sub channel valid alarm appears Using the keys O and o select yes or no Push Ent key to validate Exit the setting menu by maintaining pressure on Ent key or wait 10s and the SL50 will automatically exit the menu Note that you can stop the alarm during 10 minutes with a brief pressure on any key 1 7 Filtering of the channels The level of filtering of a channel determines the frequency of update of the data displayed For example in rough sea when the boat moves significantly it is useful to increase the filtering of the speed channel to stabilise the value displayed Conversely in calm sea low filtering will be preferable to obtain a fast response of the display Filtering is adjustable between 1 and 32 and the default value is 8 The lower this value is the higher the frequency of update is Filter setting procedure u BOAT SPEED al Using the keys W A select the channel h 1 6 8 5 from which you wish to set the filtering s 50 j Press Ent key until the list of sub channels HIGH ALARM 0 00 LOW ALARM and FIL
17. s to all channels present on the TOPLINE bus The following chapters provide detailed explanations on how to access the sub channels and implement the settings 7 SL50 User guide 33 60 022 000 1 6 Alarms setting The setting of an alarm enables you to monitor the value of a channel When the preset threshold is exceeded a warning message is displayed and an audible alarm is activated For example you can set an upper threshold and a lower threshold on the surface speed channel The upper alarm is activated when the display is higher than the programmed threshold The lower alarm is activated when the display is lower than the programmed threshold To cancel the alarm of a channel enter the value 0 in the upper alarm and the lower alarm Thus the setting of the alarms will allow you to supervise your TOPLINE installation effectively as well as the good operation of your boat Note that for angular channels such as magnetic heading or wind angle the sub channels of alarms are the alarm base and the alarm range 1 6 1 Setting procedure Using the keys W A select the channel from which you wish to set an alarm 5150 nke 5150 j Press Ent key until the list of sub channels HIGH ALARM 0 00 i i LOW ALARM and FILTERING appears nke E Then successively press Ent key to select the sub channel LOW ALARM or HIGH ALARM nke 5150 15 00 Using the keys Y A set the new ala
18. uring the procedure you can also return to the initialisation value by pressing the Ent key for 2 seconds The chronometer displays T1 6 00 minutes for a new start 1 12 2 Setting of T1 and T2 This setting can only be performed on the master display of your installation select the CHRONONOMETER channel using the Q and 4 keys press En until the message 77 setting appears change the value of T1 using the O and 4 keys then confirm with En the message T2 setting appears change the value of T2 using the Q and 4 arrow keys then confirm with the En key after 5 seconds the SL50 will automatically leave the setting mode 12 SL50 User guide 33 60 022 000 2 CALIBRATION OF SENSORS Every nke sensor is adjusted at the factory However a calibration is required to adapt the sensor to the specificities of your boat and to obtain an optimum measurement accuracy Follow the calibration procedure below by visualising the settings on a display Please refer to the installation notice of the TOPLINE sensor that you wish to calibrate 2 1 Setting procedure of calibration coefficient Example you wish to set up the calibration coefficient of the boat speed channel at this value 1 1 D 5150 using the keys Y A 1 6 8 5 select the cannal from which you wish to select the calibration coeficient nke Press Ent until the list of sub channels UNIT CALIB COEF and OFFSET appears
19. wire on init GND the SL50 takes an address available on the bus the SL50 is then initialised CAUTION the remote control s of your installation must be assigned to an address higher than the one of the SL50 To achieve that you must first initialise the SL50 then the remote control s 3 8 2 Reinitialisation procedure the SL50 already has an address between 1 and 20 You may need to reinitialise the SL50 for example to have another address assigned to it your installation is powered off disconnect the initialisation red wire from the init terminal GND power up your installation the SL50 performs an auto test then takes the address 0 when the message connect the red wire appears reconnect the red wire on init GND the SL50 takes an address available on the bus the SL50 is then initialised 20 SL50 User guide 33 60 022 000 NOTES 21 SL50 User guide 33 60 022 000 NOTES 22 SL50 User guide 33 60 022 000 NOTES 23 SL50 User guide 33 60 022 000
Download Pdf Manuals
Related Search