WaveTrax User Manual
Contents
1. TVPICAL PLASTIC ASSEMBLIES K124 Plastic Troughs Connection to K124 Junctions 8 Transi tions K124 transitions and troughs are interconnected using a GP coupling kit A K124 coupling HP kit contains a K124 plastic junction eight retainer clips and two sets of 3 8 16 bolts Trough Junction Transition and washers To Interconnect 124 Transitions and Troughs 1 Slip retainer clips onto each K124 end of the transition or trough so that the barb on each clip faces the outside of the transitions or trough e Place two clips along bottom edge of transition or trough e Place one additional clip along each side edge of trough 2 Slip slot in junction over the clips and press junction firmly onto transition or trough 3 Repeat Step 1 to install retaining clips on facing edge of next transi tion or trough 4 Slip transition or trough into the opposite end of the junction 5 Make sure junctions are tight and that barbs of retaining clips lock into grooves provided in the junction K124 troughs amp junctions require Retainer clip is installed on retainer clips trough so that barb is on outside side edges A of trough D Retainer Clip Trough A When installed on trough barb of retainer clip ge Ze will catch and hold on groove of junction 3 6 Telect Inc 107719 2 K124 Trough Na 4 20 f PAN D d Retainer Clips place 2 at bottom of transition K124 Juncti2. SUPPORT ELEMENTS Allthread Support Use the Allthread Support to attach an allthread to a ladder rack Then attach a Universal Bracket to the allthread to mount a link or transition component above or below the ladder rack Telect recommends supporting K22 and K44 link sections every 2 3 feet and K64 link sections every 2 feet Each 3 or 4 way transi tion component requires two supports 2 14 Telect Inc 107719 2 To Attach Support to a Ladder Rack 1 Slide the two halves of the bracket onto the allth read with the 3 8 slots facing each other D Attach a flat washer for 1 2 allthread only anda lock washer and nut outside each bracket half leav ing enough gap to position the bracket around the ladder rack rail 3 Position the bracket around the ladder rack rail and finger tighten the nuts To Attach a Universal Bracket to the Allthread See Page 2 5 Allthread Support Clips Use the Allthread Support Clips to attach an allthread between two adjacent overhead support channels Then attach a Uni versal Bracket to the allthread to mount a link or transition component above or below the channels Telect recommends supporting K22 and K44 link sections every 2 3 feet and K64 link sections every 2 feet Each 3 or 4 way transition compo nent requires two supports 107719 2 Telect Inc 2 15 To Attach Support Clips to Two Adjacent Support Channels 1 Slide the two clips onto the allthr
3. 2 6 Telect Inc 107719 2 2 Insert appropriate anchors and tighten Wall To Attach a Link or Transition Component to the Bracket See page Page 2 1 Ladder Rack Bracket The Ladder Rack Bracket securelv connects a section of K22 K44 or K64 links or a transition component to a l 1 2 or 2 ladder rack rail These instructions show the longer bracket for mounting a K44 or K64 link or transition compo nent The K22 link and transition components mount on a shorter bracket but the mounting sequence is the same The K124 transition components are attached to a 1 1 2 ladder rack rail using a K124 Universal Bracket shown on Page 2 5 To Attach Bracket to a Ladder Rack 1 Hook the long arm of the bracket over the ladder rack rail 2 Insert a bolt with a lock washer down through the hole in the brack et arm Telect Inc 2 7 107719 2 3 If installing the bracket on a 2 ladder rack rail place the white ny lon spacer over the shaft of the bolt underside of the rail and finger tighten the bolt into the 4 Clip the other piece of the bracket to the F threaded hole To Attach a Link or Transition Component to the Bracket See page Page 2 1 Extender Bracket The Extender Bracket supports a CMS link or a transition component awav from a 1 1 2 or 2 ladder rack The bracket attaches to the bottom of a lad der rack and is supported on each rail Two Extender Brackets are provid
4. 027 1000 4241 for two K22 Chan nels Name Extender Bracket Below Stringer Bracket Adjustable Bracket Relay Rack Duct Ex tender Bracket Component SUPPORT Install Page Page 2 14 Page 2 15 Part Numbers 027 1000 4006 with allthread bar 027 1000 4209 with allthread bar and K22 universal bracket 027 1000 4009 with allthread bar and K44 K64 universal bracket 027 1000 4082 with 24 allthread bar and K44 K64 universal bracket 027 1000 4080 for 3 span with all thread bar 027 1000 4081 for 2 span with all thread bar and K44 K64 universal bracket Telect Inc Name Allthread Support Allthread Support Clip Component 107719 2 Install Page Page 2 14 Page 2 16 Page 2 16 Page 2 18 Page 2 16 Page 2 15 107719 2 Part Numbers 1 2 18 1 2 24 M16 450mm M16 x 600mm 106736 110093 118528 118529 RR RE 027 1000 4091 10 027 1000 4092 027 1000 4093 027 1000 4013 027 1000 4490 w o Allthread Telect Inc Name Allthread Backbone Support Backbone J Hooks Backbone Splice Backbone Mount 6 Grid Mounting Bracket Kit Component 2 4 MOUNTING BRACKETS Universal Bracket The two piece Universal Bracket securelv con nects a CMS link or a transition component to a 1 or
5. 2 Pop the black button into place in the center hole To Disconnect K64 Links To disconnect links remove the black button and slide the two links apart Or open the gate and squeeze together the upper edges of both sides of the higher undimpled end of a link and pull the link itself apart To Rotate K64 Links Horizontally After two links are joined they can rotate horizontally relative to each oth er up to 25 in either direction Grasp adjacent links in each hand and rotate at the pivot point for desired amount of rotation To Rotate K64 Links Vertically An individual link can rotate in the vertical plane up to 25 in either direc tion 1 Open the gate from the link 2 Squeeze the upper edges of both sides of the higher undimpled end of the link together and rotate up or down 3 Close the gate to secure the rotation To Connect a Link to a Bracket or Transition Component See Page page 4 14 Telect Inc 4 13 107719 2 MOUNTING BRACKETS Universal Bracket The two piece Universal Bracket securelv con nects a CMS link or a transition component to a 1 or M16 allthread 1 or 2 ladder rack equipment rack or wall These instructions show the larger 4 slot bracket for mounting a K44 or a K64 link The K22 mounts on a shorter 2 slot bracket but the mounting se quence is the same K124 transitions mount on a longer bracket but again the mounting sequence is the same To Attach
6. Telect s Cable Management Systems are comprised of two separate but complimentary series of components WaveTrax and CableLinks Both series use a common set of bracketing hardware components for in stallation support WaveTrax is a raceway system that combines solid troughs with various forms of junctions intersections drops reducers and coupling compo nents to provide high capacity secure fiber optic cable routing between fi ber distribution frames and fiber optic terminal equipment 107719 2 Telect Inc 1 The complete WaveTrax system is available in 2 4 6 8 and 12 inch 51 102 152 203 and 305 mm widths The 2 inch width is available in a 2 inch 51mm depth all other widths are provided in a 4 inch 102mm depth Waverrax is designed to physically protect cable and allow for future re configuration through retrofit able components WaveTrax is an open channel system allowing easy access to ensure that fiber can be installed or removed without violating minimum bend radius WaveTrax has the following features Any desired length of run or drop Bend radius protection e Snap together channels e Totally reconfigurable e UL 94 V 0 fire retardant plastic e No special tool requirements 1 This manual also covers the Telect s CableLinks 2 Mounting Support MOUNTING Component Name Part Numbers Install Page Universal K124 Brack page lt chap et w o Allthread EE num gt 7 02
7. 107719 2 Part Numbers 027 2000 4202 2 027 2000 4002 4 027 2000 6402 6 8 2 YK YS YH 027 2000 8402 027 2000 12402 12 027 2000 4299 2 027 2000 4099 4 027 2000 6499 6 8 9 YK YH YH 027 2000 8499 8 027 2000 12499 12 027 2000 4090 K44 Link to 4 trough or K44 transition to 4 trough 027 1000 6490 K64 Link to 6 trough or K64 transition to 6 trough 027 2000 4205 027 1000 12405 027 1000 12406 027 1000 4051 027 1000 4251 Telect Inc Name Trough Lid Applica tion FastLock Coupling kit 6 Shown 6 Links Adapter 2 Universal Bracket TRAX 12 Slim Univer sal Bracket TRAX Slim Ladder Rack Kit TRAX Threaded Rod Bracket Kit Component Install Page Page 2 4 Part Numbers 027 1000 8450 027 1000 4252 027 1000 4052 027 1000 8453 027 1000 4253 027 1000 4053 027 1000 8454 027 1000 4254 027 1000 4054 422 1 1 2 rail K22 2 rail K44 K64 1 1 2 rail K44 K64 2 rail 027 1000 4204 027 1000 4244 027 1000 4004 027 1000 4044 Sa ee 027 1000 4204 K22 1 1 2 rail 027 1000 4244 K22 2 rail 027 2000 4060 for direct trough sup port Telect Inc 3 5 Name TRAX Center Below Bracket Kit TRAX C Bracket Kit TRAX L bracket Kit Universal Bracket 2 Bracket and Kit Adjustable Trough Bracket Component 107719 2
8. holes are on the same face 2 Slide the narrower bar into the broader bar 3 Match the hole of the inside bar with the nut on the outside bar 4 Insert a bolt into the brazed on nut and hole and tighten it to keep the inside bar from sliding during installation This is the maximum recommended extension length 5 Assemble two sets of J hooks on rectangular plates 6 Hang one set of J hooks on each ladder rack rail AS Ladder Rack 4 18 Telect Inc 107719 2 7 Slide the broader end of the Extender Bracket between the rectan gular plate and the ladder rack rail on each J hook set Ladder Rack 8 Finger tighten the nuts on the J hook set 9 Loosen the locking bolt adjust the extension and retighten To Attach a Link or Transition Component to the Extender Bracket The three holes on the extended end of the Extender Bracket are spaced to accommodate a K22 or K44 link or a transition component To attach a K64 link use only one hole The center hole on the end of the bracket will also hold a 1 2 allthread See page 4 9 and page 4 10 for general instructions on mounting a link or transition component to a mounting bracket Below Stringer Bracket The Below Stringer Bracket supports a CMS link or K22 K44 or K64 transition component below a ladder rack chan nel or rail Order a different part number for installation on a ladder rack a 1 x 2 channel a 2 x 2 channel a 1 4
9. or 2 ladder rack rail These instructions show the longer bracket for mounting a K44 or K64 link or transition compo nent The K22 link and transition components mount on a shorter bracket but the mounting sequence is the same The K124 transition components are attached to a 1 1 2 ladder rack rail using a K124 Universal Bracket page 4 9 To Attach Bracket to a Ladder Rack 1 Hook the long arm of the bracket over the ladder rack rail 2 Insert a bolt with a lock washer down through the hole in the brack et arm 4 16 Telect Inc 107719 2 3 If installing the bracket on a 2 ladder rack rail place the white ny lon spacer over the shaft of the bolt underside of the rail and finger tighten the bolt into the 4 Clip the other piece of the bracket to the F threaded hole To Attach a Link or Transition Component to the Bracket See page 4 9 and page 4 10 Extender Bracket The Extender Bracket supports a CMS link or a transition component awav from a 1 1 2 or 2 ladder rack The bracket attaches to the bottom of a lad der rack and is supported on each rail Two Extender Brackets are provided for each part number ordered Use two brackets to mount a transition compo nent Telect Inc 4 17 107719 2 Attach Extender Bracket to a Ladder Rack 1 Align the end of the narrower bar that has the single hole with the end of the broader bar that has the brazed on nut and so these two
10. 2000 12425 12 027 2000 4230 2 027 2000 4030 4 027 2000 6430 6 027 2000 8430 8 027 2000 12430 12 027 2000 4231 2 4 027 2000 6431 6 027 2000 8431 8 027 2000 12431 12 Name Drop Reducer Compo nent L Component 2 22 6 shown L Lid Intersection Compo nent 6 Shown Intersection Lid Component 3 2 Install Page page 3 8 page 3 8 page 3 8 Telect Inc 3 3 Part Numbers 027 2000 12452 12 to 6 027 2000 12453 12 to 8 027 2000 4050 4 to 2 027 2000 6450 6 to 4 027 2000 8450 8 to 4 027 2000 8452 8 to 6 027 2000 12450 12 to 6 027 2000 12458 12 to 8 027 1000 4007 4 027 1000 6407 6 027 1000 4015 4 027 1000 6415 6 027 2000 4208 2 027 2000 4008 4 027 2000 6408 6 027 2000 8408 6 027 2000 12408 d 6 027 2000 4000 4 027 2000 6400 6 027 2000 8400 8 027 0000 12501 12 027 2000 6401 6 027 2000 8406 8 027 2000 12400 12 Name Intersection Reducer Component 12 to 6 Shown Inline Reducer Compo nent Adapter Female Adapter Male End Cap component 5 Straight Trough 6 Straight Trough Component 107719 2 Install Page page 3 8 page 3 7 page 3 9
11. another link until the release button snaps into the release hole 107719 2 Telect Inc 4 11 Disconnect K22 K44 Links To disconnect links press the release button between the two links and while keeping it pressed pull the two links apart Or open the gate and squeeze together the upper edges of both sides of the slot end of a link and pull the link itself apart To Rotate K22 K44 Links Horizontallv After two links are joined thev can rotate horizontallv relative to each oth er up to 257 in either direction Grasp adjacent links in each hand and rotate at the pivot point for desired amount of rotation To Rotate K22 K44 Links Verticallv An individual link can rotate in the vertical plane up to 25 in either direc tion 1 Open the gate at the slot end of the link 2 Squeeze together the upper edges of both sides of the slot end and rotate up or down 3 Close the gate to secure the rotation To Connect a Link to a Bracket or Transition Component See page page 4 9 K64 Link Gate Lower dimpled End 4 12 Telect Inc 107719 2 Join K64 Links Join K64 to K64 links to make channels of any length Joining a K64 toa different size link requires the correct reducer or splitter Dissimilar ends of the K64 join 1 Slide the higher undimpled end of one link over the lower dim pled end of another link so the 3 4 tabs on each end fit into the slots on the mating link
12. nuts 107719 2 Telect Inc 2 17 Backbone Splice To Splice Two Backbone Supports 1 Position the two splice halves facing each other with the straight edges out 2 Insert the bolt between the two halves and attach the washer and nut 3 Slide each Backbone Support into one end of the splice 4 Fullv tighten the nut Backbone Support 2 18 Telect Inc 107719 2 Install Page page 3 6 page 3 6 page 3 8 page 3 6 Telect Inc 3 1 3 WaveTrax Part Numbers 027 2000 4210 2 027 2000 4010 4 027 2000 6410 6 027 2000 8410 8 027 2000 12410 12 027 2000 4211 2 027 2000 4011 4 027 2000 6411 6 027 2000 8411 8 027 2000 12411 12 027 2000 4277 2 027 2000 4077 4 027 2000 6477 6 027 2000 8477 8 027 2000 4278 2 027 2000 4078 4 027 2000 6478 6 027 2000 8478 8 to 4 027 2000 12478 12 to 6 Name T Component 6 shown T Lid Drop Component Drop Lid TRANSITION Component 107719 2 Install Page page 3 8 page 3 8 page 3 8 107719 2 Telect Inc Part Numbers 027 2000 8477 8 to 4 027 2000 12677 12 to 6 027 2000 4224 2 027 2000 4024 4 027 2000 6424 6 027 2000 8424 8 027 2000 12424 12 027 2000 4225 2 027 2000 4025 4 027 2000 6425 6 027 2000 8425 8 027
13. the edge tabs are inserted in the top edge of the intersection and the bottom of the drop swings under the intersection to latch 3 12 Telect Inc 107719 2 4 CableLinks LINKS Component Name Part Numbers Install Page 027 0000 4200 K22 S 22 444 Link 027 0000 4000 K44 page 4 10 K64 Link 027 0000 6400 page 4 11 TRANSITION Component Name Part Numbers Install Page 027 1000 4210 K22 iet at Ait jali 027 1000 4010 K44 T Metal 2 4 6 027 1000 6410 K64 page 4 28 027 1000 6451 K64 to K44 107719 2 Telect Inc 4 1 Install Page page 4 28 page 4 28 page 4 28 page 4 28 page 4 28 page 4 28 page 4 28 107719 2 Part Numbers 027 1000 4011 K44 to two K22s 027 1000 6411 K64 to two K22s 027 1000 4220 K22 027 1000 4020 K44 027 1000 6420 K64 027 1000 6421 K64 to K44 027 1000 6453 K64 to K44 or K64 to K22 when used with drop reducer 027 1000 4021 027 1000 6520 K64 to K44 K44 027 1000 4028 right shown 027 1000 4029 left K44 to K22 027 1000 4033 right shown 027 1000 4034 left 027 1000 4035 K44 to K22 027 1000 4226 K22 027 1000 4426 K44 to K22 027 1000 6426 K64 to K22 Telect Inc Name T Splitter T Drop 2 4 6 T Drop Reduced T Drop Left Right T plus Drop T plus Dual Drop Center Drop Compone
14. x 9 16 rail or below a computer floor The Below Stringer Bracket receives a K22 K44 or K64 link The illustration and instructions below apply to an installation on a ladder rack The sequence is similar for other part numbers Telect Inc 4 19 107719 2 Attach Bracket to a Ladder Rack Nvlon Spacer Optional Ladder Rack Rail 1 Wrap the small clip and the tall section around the ladder rack rail 2 Insert a bolt with a lock washer into the hole in the tall section 3 If installing the bracket on a 2 ladder rack rail place the white ny lon spacer over the shaft of the bolt 4 Finger tighten the bolt into the threaded hole in the small clip Telect Inc 107719 2 4 20 5 Slide the tall section along the channel of the L section aligning either the upper or lower set of holes with the threaded holes of the L section channel gt Ladder Rack Rail NG 58 6 Insert bolts and finger tighten To Attach 8 Link or Transition Component to the Below Stringer Bracket See page 4 9 and page 4 10 Adjustable Bracket The Adjustable Bracket consists of two L shaped pieces and it is used to connect 8 vertical section of K22 links to I the front of an equipment rack 107719 2 Telect Inc 4 21 To Attach an Adjustable Bracket to an Equipment Rack 1 Align the two of the four oval holes on the one L piece with holes in the equi
15. 1 Typical Plastic 0108 3 5 K124 Plastic Troughs Connection to K124 Junctions amp Transi BEES 3 6 K64 Plastic Troughs Connection to K64 Junctions Transitions OL DAMS EE 3 8 4 CableLinks eet EE 1 KEE E 4 1 EE A 7 Suppor GE 4 8 Typical Assemb ysis igs ck ete iota en ee 4 9 To Attach a Transition Component to a Bracket 4 9 To Attach a Link to a Bracket 4 10 To Attach a Link to a Metal Transition Component 4 10 To Attach a K64 Link or a Metal Transition Component to a 107719 2 Telect Inc 107719 2 Telect Inc Plastic TroUgh sesssoossrorersresrrrn Eet Eeer K22 K44 Links KOL ai oS ek A ou Mounting 15178068 Universal Bracket AA Ladder Rack Bracket Extender Bracket oui efterieuigees bung Below Stringer Bracket Adjustable Bracket Relay Rack Duct Extender Bracket Support Elements sssssessesssoessnrsnnrn Allthread Support sen Allthread Support 621108 Backbone Support Backbone Splice i ssa e id ti a nasal Typical Transitions Drop Reducer issa tea Owner Maintenance s s s In Warrantv Service Out Of Warrantv Service Repacking For Shipment 5 Service iv CABLE MANAGEMENT SYSTEM 5 6 pinch GableLinks CabteLinics Adame f ing Channel dingh Ghannal finch in 4 inch Reducer Sinh T Tramaition gt Description
16. 3 Slide each Backbone Support into one end of the splice 4 Fullv tighten the nut Backbone Support TRANSITIONS The attachment ends of the transition IL components are either straight ends Sg drops or splits Each end attaches in a similar way to a mounting bracket see a page 3 7 e Each K22 K44 and K64 end attaches in a similar way to a link The exception to this is the K22 K44 and K64 center drop and the straight metal sections see page 4 9 and the K64 adapter see page 4 11 Each of the K124 ends on K124 transitions receives a K124 junction which in turn receives the end of another K124 transition or a K124 trough see page 4 11 Telect suggests mounting transition components before attaching links to them If not be sure to place hex bolts through the slotted bars on the un derside of the component before attaching links Otherwise they will not fit in 107719 2 Telect Inc 4 27 Tvpical Transitions Straight End See page 4 10 for typical assembly instruc tions Drop End 144 drops have slot spacing to receive a 44 or a 22 link Almost all 4 drops receive K44 links The straight drop PN 027 1000 6412 receives one K64 link or two K22 links However do not attach a K22 link to a K44 drop without the addition of a reducer PN 027 1000 4021 See page 4 9 for reducer attachment instructions See page 4 10 for typical assembly instructions for attaching a link to a tran
17. 7 1000 12409 with M16 450mm Universal K124 Brack All thread page lt chap et With Allthread 027 1000 12482 with M16 x 600mm num gt 7 All thread TRAX 12 Slim Univer sal Bracket 027 1000 12405 TRAX Slim Ladder Rack Kit 027 1000 12406 TRAX Threaded Rod 027 1000 4051 Bracket Kit 027 1000 4251 107719 2 Telect Inc 2 1 Install Page Page 2 5 Page 2 7 107719 2 Part Numbers 027 1000 8450 027 1000 4252 027 1000 4052 027 1000 8453 027 1000 4253 027 1000 4053 027 1000 8454 027 1000 4254 027 1000 4054 422 1 1 2 rail K22 2 rail K44 K64 1 1 2 rail K44 K64 2 rail 027 1000 4204 027 1000 4244 027 1000 4004 027 1000 4044 027 1000 4204 K22 1 1 2 rail 027 1000 4244 K22 2 rail 027 2000 4205 027 1000 4260 K22 027 1000 4060 K44 K64 Telect Inc Name TRAX Center Below Bracket Kit TRAX C Bracket Kit TRAX L bracket Kit Universal Bracket 2 Bracket and Kit CableLinx 2 Universal Bracket WaveTrax Ladder Rack Bracket Component Install Page Page 2 8 Page 2 10 Page 2 13 Page 2 14 Part Numbers 027 1000 4005 027 1000 4090 ladder rack 027 1000 4094 3 4 rod 027 1000 4095 1 square channel 027 1000 4096 1 4 x 9 16 bar 027 1000 4098 beneath floor 027 1000 4211 027 1000 4221 for K22 or K44 Chan nel
18. Bracket to an Allthread 1 When using a metal bracket cover allthread with the right rubber tubing for its size to protect it where the bracket attaches 2 Align the two bracket pieces with the allthread between them The bracket can mount either lengthwise or crosswise on the allthread 3 Insert carriage bolts with the square shaft in the square holes of the bracket back attach nuts and finger tighten Rubber Tubing Allthread KG Attach Bracket to a Ladder Rack 1 Align the two bracket pieces with the ladder rack rail between them The bracket mounts onlv crosswise on the rail 4 14 Telect Inc 107719 2 2 Insert carriage bolts with the square shaft in the square holes of the bracket back attach nuts and finger tighten Ladder Rack To Attach Bracket to an Equipment Rack 1 Use oniv the front L shaped bracket piece 2 Align the bracket with the holes in the equipment rack 3 Insert two screws and fully tighten Equipment Rack N lt gt se 0 6 To Attach Bracket to a Wall 1 Use only the front L shaped bracket piece 107719 2 Telect Inc 4 15 2 Insert appropriate anchors and tighten Wall To Attach a Link or Transition Component to the Bracket See page 4 9 and page 4 10 Ladder Rack Bracket The Ladder Rack Bracket securelv connects a section of K22 K44 or K64 links or a transition component to a 1 1 2
19. CONNECTING THE FUTURE WAVETRAX USER MANUAL 107719 2A0 WAVETRAX User Manual Document Number 107719 1A0 Copyright 2001 Telect Inc All Rights Reserved 76160169 and Connecting the Future are registered trademarks of 161606 Inc 2111 N Molter Rd Liberty Lake Washington 99019 Technical Support By e mail getinfo telect com By phone 888 821 4856 or 509 921 6161 Note Telect assumes no liability from the application or use of these products Neither does Telect convey any license un der its patent rights nor the patent rights of others This document and the products described herein are subject to change without notice ii Telect Inc 000000A0 Telect Inc 2111 N Molter Rd P O Box 665 Libertv Lake WA 99019 509 926 6000 800 551 4567 Fax 509 926 8915 E mail getinfo telect com Internet http www telect com Contents iii 1 Descriptions 2 Mounting Support SPT RE 2 2 Universal Bracket sssssssissuisisstssssssssssnsissssssssnssrensissrssnssessrnnss 2 3 Ladder Rack Bracket jr sekker Sedan 2 6 Extender Bra ket ss een isa iii iku bi pie iu f ed 2 7 Bel w Stringer Bracket 1i skkiibiziii cee ae ee 2 9 Adjustable Bracket sister ii na a Ma ssa ita a candace ais 2 11 Relay Rack Duct Extender Bracket AA 2 12 S pport antvanesdesyeeseunees 2 12 Allthr ad SUppOrt 2 12 Allthread Support Clips spasere eee 2 13 Backbone S pp tt iii ae as thes 2 14 3 WaveTrax Kee te EE 3
20. M16 allthread 142 or 2 ladder rack equipment rack or wall These instructions show the larger 4 slot bracket for mounting a K44 or a K64 link The K22 mounts on a shorter 2 slot bracket but the mounting se quence is the same K124 transitions mount on a longer bracket but again the mounting sequence is the same To Attach Bracket to an Allthread 1 When using a metal bracket cover allthread with the right rubber tubing for its size to protect it where the bracket attaches 2 Align the two bracket pieces with the allthread between them The bracket can mount either lengthwise or crosswise on the allthread 3 Insert carriage bolts with the square shaft in the square holes of the bracket back attach nuts and finger tighten Rubber Tubing Allthread KA 107719 2 Telect Inc 2 5 To Attach Bracket to a Ladder Rack 1 Align the two bracket pieces with the ladder rack rail between them The bracket mounts onlv crosswise on the rail 25 Insert carriage bolts with the square shaft in the square holes of the bracket back attach nuts and finger tighten Ladder Rack To Attach Bracket to an Equipment Rack 1 Use only the front L shaped bracket piece 2 Align the bracket with the holes in the equipment rack 3 Insert two screws and fully tighten Equipment Rack N To Attach Bracket to a Wall 1 Use only the front L shaped bracket piece
21. d Gate Removed for Claritv l I LB Mounting Bracket et Set To Attach a Link to a Metal Transition Component In general links attach to transition components by sliding either end of the link between the slotted base of the transition component and the bottom of the component Links should be flat that is not rotated vertically or hori zontally The link slides completely into the slots of the transition compo nent Links attach to transition components with carriage bolts q Carriage Bolt Link Partially Inserted in Transition Component Slot in Base of Transition Transition Component 4 10 Telect Inc 107719 2 Attach a 464 Link or a Metal Transition Component to a Plastic Trough This requires a K64 or K124 adaptor See page page 4 28 LINKS The K22 K44 and K64 links and corresponding straight sections troughs form the basis building blocks of the CMS They join to form secure chan nels for carrying and protecting cable e The K22 has a 2 x 2 inside channel e The K44 has a 4 x 4 inside channel e The K64 has a 6 x 4 inside channel K22 K44 Links Tongue Gate 9 Anchor Hole Release Button Release Hole Slot To Join K22 K44 Links Join K22 to K22 links and K44 to K44 links to make channels of anv length Joining dissimilar links requires the correct reducer or splitter To join similar links slide the tongue of one link into the slot of
22. ead with the bent over sides facing each other 2 Attach a flat washer for 1 2 allthread only and a lock washer and nut on the allthread outside each clip leaving enough gap to position the clips around the support channels 3 Position one clip above and one clip below the sup port channels Finger tighten the nuts Support Channel To Attach a Universal Bracket to the Allthread See Page 2 5 Backbone Support Use the Backbone Support to bridge an open span between overhead support channels and create a FS runway for K44 links Use Backbone J Hooksto i gt attach the Backbone Support to the support chan nels To splice to another Backbone Support for a longer span use a Back bone Splice Use the Backbone Mount to mount K44 links along the Back bone Support 2 16 Telect Inc 107719 2 To Attach the Backbone Support to a Support Channel 1 Lav the Backbone Support face down across the open span 2 Assemble two sets of J hooks on rectangular plates 3 Lay the rectangular plate of the J hook as sembly on the Backbone Support where it crosses the support channel at one end and hook EZ EZ the T s around the channel EN EN Support Channel 4 Finger tighten the nuts 5 Lay the rectangular plate of the other J hook assembly on the Backbone Support where it crosses the support channel at the other end and hook the J s around the channel 6 Finger tighten the
23. ecommends supporting K22 and K44 link sections every 2 3 feet and K64 link sections every 2 feet Each 3 or 4 way transi tion component requires two supports 107719 2 Telect Inc 4 23 To Attach Support to a Ladder Rack 1 Slide the two halves of the bracket onto the allth read with the 3 8 slots facing each other 2 Attach a flat washer for 1 2 811002680 only and a lock washer and nut outside each bracket half leav ing enough gap to position the bracket around the ladder rack rail 3 Position the bracket around the ladder rack rail and finger tighten the nuts Attach a Universal Bracket to the Allthread See 4 10 Allthread Support Clips Use the Allthread Support Clips to attach an allthread between two adjacent overhead support channels Then attach a Uni versal Bracket to the allthread to mount a link or transition component above or below the channels Telect recommends supporting K22 and K44 link sections every 2 3 feet and K64 link sections every 2 feet Each 3 or 4 way transition compo nent requires two supports 4 24 Telect Inc 107719 2 To Attach Support Clips to Two Adjacent Support Channels 1 Slide the two clips onto the allthread with the bent over sides facing each other 2 Attach a flat washer for 1 2 allthread only and a lock washer and nut on the allthread outside each clip leaving enough gap to position the clips around the support channels 3 Posit
24. ed for each part number ordered Use two brackets to mount a transition compo nent 2 8 Telect Inc 107719 2 Attach Extender Bracket to a Ladder Rack 1 Align the end of the narrower bar that has the single hole with the end of the broader bar that has the brazed on nut and so these two holes are on the same face Slide the narrower bar into the broader bar Match the hole of the inside bar with the nut on the outside bar Insert a bolt into the brazed on nut and hole and tighten it to keep the inside bar from sliding during installation This is the maximum recommended extension length Assemble two sets of J hooks on rectangular plates Hang one set of J hooks on each ladder rack rail N Ladder Rack 107719 2 Telect Inc 2 9 7 Slide the broader end of the Extender Bracket between the rectan gular plate and the ladder rack rail on each J hook set Ladder Rack 8 Finger tighten the nuts on the J hook set 9 Loosen the locking bolt adjust the extension and retighten To Attach a Link or Transition Component to the Extender Bracket The three holes on the extended end of the Extender Bracket are spaced to accommodate a K22 or KA4 link or a transition component To attach a K64 link use only one hole The center hole on the end of the bracket will also hold a 1 2 allthread See page 4 10 and page 4 11 for general instructions on mounting a link or transi
25. finger tighten End Cap The End Cap terminates a channel at a link The End Cap can be placed over either end of the link These illustrations show the installation of the K22 End Cap The K44 and K64 End Caps differ slightly but install similarly 1 Position the End Cap with the overhanging roof on top and the bottom open 2 Hook the tabs of the roof into the forward slots of the gate Tabs Hook into Slots on Gate 107719 2 Telect Inc 4 31 3 Slide the End Cap over the end of the link so that the long side clips engage below the outside rib of the link and the small side clips are against the front edge End Cap Link L R Outside Link and Against Edge of Link Below Rib Center Drop Straight Metal Section Links attach to the Center Drops and Straight Metal Sections differently than they do to the other transition compo nents If using K124 or K64 plastic troughs refer to page 3 6 and page 3 8 respectively To Attach 8 Link to a Center Drop or K22 K44 K64 Straight Met al Section 1 Place the end of the drop or section entirelv within the link D Align the slots of the trough end with the bolt holes in the link 3 Insert carriage bolts attach nuts and finger tighten 4 32 Telect Inc 107719 2 To Attach a Center Drop or K22 K44 K64 Straight Metal Section to a Mounting Bracket These components do not attach to m
26. ight shown 027 1000 4037 left Telect Inc Name Corner Left Drop Right Corner Right Drop Left Intersection Metal 2 4 6 Drop Intersection 2 4 6 Drop Intersection 12 to 6 Saddle Intersection plus Drop Component Install Page page 4 28 page 4 28 page 4 28 page 4 28 page 4 30 page 4 30 page 4 31 Telect Inc 4 5 Part Numbers 027 1000 4050 K44 to K22 027 1000 6450 K64 to K44 027 1000 4021 K44 to K22 or to K44 027 1000 4040 K44 to two K22s 027 1000 6440 K64 to two K22s 027 1000 4212 K22 027 1000 4012 K44 027 1000 6412 K64 to K64 or K64 to two K22s 027 1000 4007 K44 027 1000 6407 K64 027 1000 4015 K44 027 1000 6415 K64 027 1000 4208 K22 027 1000 4008 K44 027 1000 6408 K64 Name In line Reducer Drop Reducer Splitter Straight Drop Adapter Female Adapter Male End Cap Component Install Page page 4 11 page 3 8 page 3 29 107719 2 Part Numbers 027 0000 6502 K64 with cover 027 0000 6501 K64 without cover 027 1000 4500 K44 with cover 027 1000 4501 K44 without cover 027 1000 4502 K44 cover 027 1000 6500 K64 with cover 027 1000 6501 K64 without cover 027 1000 6502 K64 cover only 027 1000 6490 K64 Link to 6 trough or K64 transit
27. ion one clip above and one clip below the sup port channels Finger tighten the nuts Support Channel To Attach a Universal Bracket to the Allthread See page 4 14 Backbone Support Use the Backbone Support to bridge an open span between overhead support channels and create a BE runway for K44 links Use Backbone J Hooks to e a attach the Backbone Support to the support chan nels To splice to another Backbone Support for a longer span use a Back bone Splice Use the Backbone Mount to mount K44 links along the Back bone Support 107719 2 Telect Inc 4 25 To Attach the Backbone Support to a Support Channel 1 Lav the Backbone Support face down across the open span 2 Assemble two sets of J hooks on rectangular plates 3 Lay the rectangular plate of the J hook as sembly on the Backbone Support where it crosses the support channel at one end and hook EZ EZ the J s around the channel Support Channel 4 Finger tighten the nuts 5 Lay the rectangular plate of the other J hook assembly on the Backbone Support where it crosses the support channel at the other end and hook the J s around the channel 6 Finger tighten the nuts 4 26 Telect Inc 107719 2 Backbone Splice To Splice Two Backbone Supports 1 Position the two splice halves facing each other with the straight edges out 2 Insert the bolt between the two halves and attach the washer and nut
28. ion to 6 trough 027 1000 4050 K44 to K22 027 1000 6450 K64 to K44 Telect Inc Name 5 Straight Metal Section 6 Links Adapter Reducer Component 4 6 MOUNTING Install Page page 4 14 page 4 16 page 4 17 page 4 19 page 4 21 page 4 23 Part Numbers 422 1 1 2 rail K22 2 rail K44 K64 1 1 2 rail K44 K64 2 rail 027 1000 4204 027 1000 4244 027 1000 4004 027 1000 4044 027 1000 4260 K22 027 1000 4060 K44 K64 027 1000 4005 027 1000 4090 ladder rack 027 1000 4094 3 4 rod 027 1000 4095 1 square channel 027 1000 4096 1 4 x 9 16 bar 027 1000 4098 beneath floor 027 1000 4211 027 1000 4221 for K22 or K44 Chan nel 027 1000 4241 for two K22 Channels Telect Inc 4 7 Name Universal Bracket Ladder Rack Bracket Extender Bracket Below Stringer Bracket Adjustable Bracket Relay Rack Duct Ex tender Bracket Component 107719 2 SUPPORT Install Page page 4 23 page 4 24 page 4 23 page 4 25 page 4 25 page 4 27 page 4 27 107719 2 Part Numbers 027 1000 4006 with allthread bar 027 1000 4209 with allthread bar and K22 universal bracket 027 1000 4009 with allthread bar and K44 K64 universal bracket 027 1000 4082 with 24 allthread bar and K44 K64 universal bracket 027 1000 4080 for 3 span with all th
29. nsists of two L shaped pieces and it is used to connect a vertical section of K22 links to the front of an equipment rack To Attach an Adjustable Bracket to an Equipment Rack 1 Align the two of the four oval holes on the one L piece with holes in the equipment rack Equipment Rack 2 Insert screws and fullv tighten 3 Place the two ears of the other L piece into the long slots on the attached L to form a channel with the threaded hole on the inside 4 Insert a bolt with a washer through the long slot and into the threaded hole 5 Adjust the width of the channel by sliding the pieces and tighten the bolt To Attach a K22 Link to the Adjustable Bracket A K22 link would normallv attach vertically to the Adjustable Bracket See page 4 10 for instructions on attaching a link to a bracket 107719 2 Telect Inc 2 13 Relav Rack Duct Extender Bracket K22 Link SE S B I w 3 a o E D S A A KN P T 5 1 4 20 x 1 Carriage Bolts 2 K22 K44 Relay Rack Duct Extender Bracket 12 24 x 1 2 Screws 2 12 24 Lock Washers 2 12 24 Flat Washers 2 12 24 x 1 2 Screws 2 12 Lock Washers 2 12 Flat Washers 2 K22 Links 1 4 20 x 1 Carriage Bolts 4 1 4 20 Flange Nuts 2 Dual K22 Relay Rack Duct Extender Bracket Foot of Rack 12 24 x Screws 2 12 24 Lock Washers 2 12 24 Flat Washers 2
30. nt Install Page page 4 28 page 4 28 page 4 28 page 4 28 page 4 28 page 4 28 page 4 28 Part Numbers 027 1000 4070 K44 to two K22s 027 1000 6470 K64 to two K22s 027 1000 4225 K22 027 1000 4025 K44 027 1000 4224 K22 027 1000 4024 K44 027 1000 6424 K64 K44 to two K22s 027 1000 4016 right shown 027 1000 4017 left K64 to two K22s 027 1000 6416 right 027 1000 6417 left K22 027 1000 4218 right 027 1000 4219 left K44 027 1000 4018 right 027 1000 4019 left shown K64 027 1000 6418 right to K44 027 1000 6419 left to K44 027 1000 4026 K44 027 1000 4027 K44 Telect Inc 4 3 Name Drop Splitter End Run Saddle L Metal 2 4 6 End Run Splitter End Run Drop Corner Right Drop Right Corner Left Drop Left Component Install Page page 4 28 page 4 28 page 4 28 page 4 28 page 4 28 page 4 28 page 4 28 107719 2 Part Numbers 027 1000 4031 K44 027 1000 4032 K44 K22 K44 K64 K64 to K44 027 1000 4230 027 1000 4030 027 1000 6430 027 1000 6452 Sas K22 K44 K64 K64 to K44 027 1000 4222 027 1000 4022 027 1000 6422 027 1000 6454 ae eg Een 027 1000 12453 K124 to K64 027 1000 4223 K22 027 1000 4023 K44 027 1000 6455 K64 to K44 K44 to K22 027 1000 4036 r
31. on in coupling kit Mounting Bolt l Mina K124 Universal Bracket 7 All hardware included in coupling kit Joining a K124 Transition to a K124 Trough Z K124 Trough Z AD JP AK ot g l 2 C g AA U G p p 6 A lt 2 SN A i Retainer Clips 8 included in K124 coupling kit K124 Junction in coupling kit Mounting Bolt f Z 2 K124 Universal Bracket SC 1 ordered separatel 4 be All in kit Joining Two K124 Troughs 107719 2 Telect Inc 3 7 To Disconnect K124 Transitions and Troughs You must separate the upper and lower halves of the junction Remove four screws on the bottom and two on the sides To Mount K124 Junctions K124 junctions attach to universal K124 brackets using the two mounting bolts and washers included in the K124 coupling kit K64 Plastic Troughs Connection to K64 Junctions Transitions amp Links K64 plastic troughs require an adapter for attaching them to other K64 links or K64 metal transitions Adapters are in cluded in adapter kits each kit containing one metal adapter channel two retainer clips and a pair of 3 8 16 carriage bolts nuts and washers Trough K64 plastic troughs are con nected to other K64 plastic Adapter Link Transition troughs and plastic transitions using a K64 coupling kit simi lar Each 64 coupling kit contains two sets 01 3 8 16 bolts nuts and washers To Interconnect K64 Troughs to K64 Metal Transitions am
32. ounting brackets directiv but rather require an intervening link see 3 10 Once the component is attached to a link either 1 Remove the carriage bolts 2 Align the slots in the straight section and the link bolt holes with the slots in the mounting bracket 3 Replace the carriage bolts through all three units attach nuts and finger tighten Or 1 Align the bolt holes on the other end of the link with slots in the mounting bracket 2 Insert hex bolts attach nuts and finger tighten 107719 2 Telect Inc 4 33 To Attach a Link to the Drop Portion of a Center Drop 1 Attach the slotted plate behind the center plate of the drop using the screws provided O 3 Insert carriage bolts through the slotted piece and through the bolt holes of the link attach nuts and finger tighten 4 34 Telect Inc 107719 2 D Service OWNER MAINTENANCE Telect s WaveTrax and CableLinks components do not need preventive maintenance IN WARRANTV SERVICE Contact vour Telect equipment distributor or call a Telect Customer Ser vice Representative l 800 551 4567 1 509 926 6000 Telect will repair or replace defective products within the limits of the war ranty See Repacking for Shipment in this section NOTE Call a Customer Service Representative for a Return Material Authoriza tion RMA before returning any equipment OUT OF WARRANTY SERVICE The
33. p Links 1 Slip two retainer clips onto bottom edge of trough so that the barb on each clip faces the outside of trough 2 Slip slot in bottom edge of adapter over the clips on the trough and firmly press components together 3 Slip adapter end of assembly into K64 transition or link and fasten with carriage bolts nuts and washers provided with adapter 4 Make sure retaining clips lock into grooves in adapter slot Telect Inc 107719 2 K64 Adapter K64 Trough K64 Link K64 Adapter K64 Trough 2 K64 Metal Transition Joining a K64 Metal Transition to a K64 Trough To Interconnect K64 Plastic Troughs 1 Slip retainer clips onto each K64 end of the transition or trough so that the barb on each clip faces the outside of the transitions or trough e Place two clips along bottom edge of transition or trough e Place one additional clip along each side edge of trough 2 Slip slot in junction over clips and press firmly onto trough 3 Repeat Step 1 to install clips on facing edge of next trough A Slip that trough into the opposite end of the junction 107719 2 Telect Inc 3 9 5 Make sure junctions are tight and that barbs of retaining clips lock into grooves provided in the junction K64 Trough A JP y Retainer Clips E kr in K64 coupling kit K64 Junction in coupling kit Mounting Bolt 1 a K64 Universal Bracket All hardware included in coupling kit Joining Two K64 Tro
34. pment rack Equipment Rack 0 2 Insert screws and fully tighten 0 GI H Ze of Bh ie U d ISL 3 Place the two ears of the other L piece into the long slots on the attached L to form a channel with the threaded hole on the inside 4 Insert a bolt with a washer through the long slot and into the threaded hole De Adjust the width of the channel by sliding the pieces and tighten the bolt To Attach a K22 Link to the Adjustable Bracket A K22 link would normally attach vertically to the Adjustable Bracket See page 4 10 for instructions on attaching a link to a bracket 4 22 Telect Inc 107719 2 Relav Rack Duct Extender Bracket K22 Link 1 4 20 Flange Nuts 2 1 4 20 x 1 Carriage Bolts 2 va 3 8 16 1 Carriage Bolts 2 7 K22 K44 Relay Rack Duct Extender Bracket 12 24 x 1 2 Screws 2 12 Lock Washers 2 12 Flat Washers 2 SW 12 24 1 2 Screws 2 FJ 12 24 Lock Washers 2 12 24 Flat Washers 2 1 4 20 1 Carriage Bolts 4 1 4 20 Flange Nuts 2 Dual K22 Relay Rack Duct Extender Bracket Foot of Rack 12 24 x Screws 2 12 24 Lock Washers 2 12 24 Flat Washers 2 SUPPORT ELEMENTS Allthread Support Use the Allthread Support to attach an allthread to a ladder rack Then attach a Universal Bracket to the allthread to mount a link or transition component above or below the ladder rack Telect r
35. procedure for out of warranty service is the same as for in warranty service except that Telect charges a processing fee and you must submit a Purchase Order along with a Return Material Authorization RMA before returning equipment Call a Customer Service Representative for help get ting these forms 107719 2 Telect Inc 5 1 The processing fee guarantees a repair estimate and is credited against ac tual material and labor costs REPACKING FOR SHIPMENT Step Action 1 Tag the equipment showing owner s name address and telephone number together with a detailed description of the problem 2 Use the original shipping container if possible If vou do not have it package the equipment in a way to prevent shipping damage In clude the RMA outside and inside the container 3 Insure the package NOTE Telect is not liable for shipping damage 5 2 Telect Inc 107719 2
36. read bar 027 1000 4081 for 2 span with all thread bar and K44 K64 universal bracket 106736 110093 118528 118529 1 2 x 18 1 2 x 24 M16 x 450mm M16 x 600mm annann 027 1000 4091 10 027 1000 4092 027 1000 4093 027 1000 4013 Telect Inc Component Name Allthread Support Allthread Support Clip Allthread Backbone Support Backbone J Hooks Backbone Splice Backbone Mount Component Name Part Numbers Install Page 6 Grid Mounting Brack et Kit 027 1000 4490 w o Allthread TVPICAL ASSEMBLV To Attach a Transition Component to a Bracket In general K22 K44 K64 metal transition components intersections drops reducers splitters and plastic junctions attach to mounting brackets with hex bolts The bolts go down through a slotted bar on the underside of the transition or junction piece The head of the bolt fits within the slotted bar and the nut attaches at the bracket Metal Transition Component Mounting Bracket Ends of K64 or K124 plastic transitions are coupled to plastic junctions See page 4 28 The junctions mount to brackets 107719 2 Telect Inc 4 9 To Attach a Link to In general links attach to mounting brackets with hex bolts The bolts go down through the link so that the head fits into the hexagonal anchor hole in the link Hex Bolt Link Forwar
37. sition component Split End K44 and K64 splits receive two K22 links side by side See page 4 10 for typical assembly instruc tions for attaching a link to a transition component Drop Reducer The Drop Reducer provides a transition over a drop from one size of link to a smaller size Do not attach a K22 link to a K44 drop without using a Drop Reducer 4 28 Telect Inc 107719 2 To Construct a Drop Reducer Construct the Drop Reducer by adding two metal plates PN 027 1000 4021 to a straight drop 1 Position the reducer plate so the attachment ears are outside the ca ble channel and the holes in the ears are lined up with the small holes in the drop 2 Insert the small Phillips screws provided and tighten Drop 9 Reducer To Attach the Reducer to a Bracket See page 4 9 To Attacha Link to the Reducer See page 4 10 107719 2 Telect Inc 4 29 Adapter Male Female The Adapter joins an existing cable trough to a link 1 Insert hex bolts into each of the four attachment tabs on the Adapter with the head toward the inside of the Adapter trough 2 Slide the attachment tabs with bolts into the side and bottom grooves of the trough Cable Trough 4 30 Telect Inc 107719 2 3 Place clips over the bolts like washers with the ears extended along the grooves 4 Attach nuts and
38. tion component to a mounting bracket Below Stringer Bracket The Below Stringer Bracket supports a CMS link or K22 K44 or K64 transition component below a ladder rack chan nel or rail Order a different part number for installation on a ladder rack a 1 x 2 channel a 2 x 2 channel a 1 4 x 9 16 rail or below a computer floor The Below Stringer Bracket receives a K22 K44 or K64 link The illustration and instructions below apply to an installation on a ladder rack The sequence is similar for other part numbers 2 10 Telect Inc 107719 2 Attach Bracket to a Ladder Rack Nvlon Spacer Optional Ladder Rack Rail 1 Wrap the small clip and the tall section around the ladder rack rail 2 Insert a bolt with a lock washer into the hole in the tall section 3 If installing the bracket on a 2 ladder rack rail place the white ny lon spacer over the shaft of the bolt 4 Finger tighten the bolt into the threaded hole in the small clip Telect Inc 2 11 107719 2 5 Slide the tall section along the channel of the L section aligning either the upper or lower set of holes with the threaded holes of the L section channel AE Ladder Rack Rail NG 58 6 Insert bolts and finger tighten To Attach 8 Link or Transition Component to the Below Stringer Bracket See Pages 4 9 and 4 10 2 12 Telect Inc 107719 2 Adjustable Bracket The Adjustable Bracket co
39. ughs To Disconnect K64 Plastic Troughs from K64 Plastic Transi tions and Troughs You must separate the upper and lower halves of the junction as follows 1 See the following illustrations and using a small screwdriver press in one of the snaps located near the top of junction wall Pull up slightly on upper half to junctions to prevent the snap from re en gaging 2 Squeeze together the closest pair of snaps on the bottom of the as sembly Pull up slightly to prevent the snaps from re engaging Squeeze together the next pair of snaps 4 If necessary press in other snap to separate two halves of junction 3 10 Telect Inc 107719 2 Lower Half Push in Snap With Small Screwdriver and Then Pull Up Slightly on Upper Half of Junction Push in Other Snap and Then Pull Apart Upper amp Lower Halves of Junction 2 Squeeze Together This Pair of Snaps so That They Disengage Lower Half of Junction Squeeze Together Next Pair of Snaps so That They Disengage Lower Half of Junction To Mount K64 Junctions amp Adapters K64 junctions and adapters attach to universal K64 brackets using the two mounting bolts nuts and washers included with the K64 junction or adapt 3 11 Telect Inc er 107719 2 Mount Drops Drops and trumpets have built in edge tabs and bottom latching plates al lowing them to lock into junctions T s L s and intersections As show be low
Download Pdf Manuals
Related Search