User Manual ARK-1382
Contents
1. i TE H H H Unscrew the 4 hex bolts on the rear panel 6 38 ARK 1382 User Manual 7 Remove the antenna mounting nut 8 Flip the case over and pull the carrier board out being careful with the thermal pad 39 ARK 1382 User Manual 9 Memory socket 10 MiniPCI socket I LJ s ARK 1382 User Manual 40 11 Jumper settings See Locating Jumpers on the Board on page 15 3 E in N K KI NOTE Ze Ya mu 3 Mm nd n 3 a p 41 ARK 1382 User Manual ARK 1382 User Manual 42 N a Realtek RTL8111B 8111C Gigabit Boot Agent Configuration Menu A 1 Realtek RTL8111B 8111C Gigabit Boot Agent Configuration Menu This appendix allows the user to control the Boot Agent Setup Menu 1 When a boot from LAN application is required press Shift F10 during system initialization This will take you to the Boot Agent Setup Menu 2 Inthe Boot Agent Setup Menu go to Network Boot Protocol choose the pre ferred protocol from the choices PXE and RPL ARK 1382 User Manual 44 Appendix A Realtek RTL8111B 8111C Gigabit Boot Agent Configuration Menu ARK 1382 User Manual 45 Trusted ePlatform Services AD ANTECH www advantech com Please verify specifications before quoting This guide is intended for reference purposes only All product specifications are subject to c2. ARK 1382 Ultra Compact Embedded System Trusted ePlatform Services AD ANTECH Copyright The documentation and the software included with this product are copyrighted 2008 by Advantech Co Ltd All rights are reserved Advantech Co Ltd reserves the right to make improvements in the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of Advantech Co Ltd Information provided in this manual is intended to be accurate and reliable How ever Advantech Co Ltd assumes no responsibility for its use nor for any infringe ments of the rights of third parties which may result from its use Acknowledgements Intel and Pentium are trademarks of Intel Corporation Microsoft Windows and MS DOS are registered trademarks of Microsoft Corp All other product names or trademarks are properties of their respective owners Product Warranty 2 years Advantech warrants to you the original purchaser that each of its products will be free from defects in materials and workmanship for two years from the date of pur chase This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech or which have been subject to misuse abuse accident or improper installation Advantech assumes no liability under the terms
3. 12 2 1 2 Jumper Setting 2 1 2 1 COM1 Jumper ARK 1382 series uses jumpers JP1 JP3 located on the internal carrier board for COM1 selecting the RS 232 RS422 and RS485 JP1 Close pins Function 1 3 RS 232 2 4 RS 232 3 5 RS 422 RS 485 4 6 RS422 RS 485 means default setting of the jumper function JP2 Close pins Function 1 3 RS 232 2 4 RS 232 3 5 RS 422 RS 485 4 6 RS 422 RS 485 means default setting of the jumper function JP3 Close pins Function 1 2 RS 485 3 4 RS 422 5 6 RS 232 means default setting of the jumper function 13 ARK 1382 User Manual 2 1 2 2 COM2 Jumper ARK 1382 uses jumpers JP4 JP6 located on the internal carrier board for COM2 selecting RS 232 RS422 and RS485 JP4 Close pins Function 1 3 RS 232 2 4 RS 232 3 5 RS 422 RS 485 4 6 RS422 RS 485 means default setting of the jumper function JP5 Close pins Function 1 3 RS 232 2 4 RS 232 3 5 RS 422 RS 485 4 6 RS 422 RS 485 means default setting of the jumper function JP6 Close pins Function 1 2 RS 485 3 4 RS 422 5 6 RS 232 means default setting of the jumper function 2 1 2 3 CMOS Jumper JP8 ARK 1382 uses jumper JP8 located on the internal carrier board for selecting the CMOS for Clear or Normal status Close pins Function 1 2 Clear CMOS 2 3 Normal means default setting of the jumper function ARK 1382 User Manual 14 2 1 3 Locating Jumpers on
4. ARK 1382 Compact Embedded Computer is equipped with a solid state onboard CF card of up to 8 GB so it easily passes 50 and 5 Grms shock and vibration tests ARK 1000 can be standalone wall mounted DIN rail mounted or VESA mounted The series accepts a wide range of power supplies DC power in and comes in a footprint of only 189 x 41 x 130 6 mm 7 44 x 1 61 x 5 14 The rugged cast alumi num case not only provides great protection from EMI shock vibration cold and heat but also passive cooling for super quiet fanless operation ARK 1382 User Manual 2 1 2 1 2 1 1 2 2 Product Feature General CPU Intel ULV Celeron M 423 1 06GHz Core Duo ULV U2500 1 2GHz m System Chipset 945GM chipset 533 MHz FSB m BIOS AWARD 4 Mbit Flash BIOS m System Memory 200 pin SODIMM socket Supports ECC Double Data Rate DDR2 128 MB to 1 GB DDR2 400 533 MHz m Power Management APM1 2 ACPI 2 0 support m SSD Supports CompactFlash Card TYPE I II shared 1st IDE Channel USB memory m Watchdog Timer Single chip Watchdog 255 level interval timer setup by soft ware m Expansion Interface 1 x miniPCI Equipped with miniPCI WLAN card for ARK 1382W version m Battery 3V 210 mAh m I O Interface 2 x RS232 422 485 default is RS 232 RS 422 485 by jumper setting m USB 5 x USB 2 0 compliant Ports one combined with eSATA m Audio ALC203 AC97 surround stereo sound and dual output 2 2 W amplifier Supports Line out Left and Ri
5. ARK 1382 is equipped with an external CF card Power ON OFF Button ARK 1382 comes with a Power On Off button that supports the dual functions of Soft Power On Off Instant off or 4 sec delay and Suspend LED Indicators There are four LEDs on ARK 1382 front metal face plate for indicating system status PWR LED is for power status and flashes green in color HDD LED is for Compact Flash disk status which flashes red in color Normal LED detects if the internal tem perature is under 90 C which flashes blue in color but when the internal temperature is over 90 C the Normal blue LED will not flash and the orange alarm LED will flash which means the user must enhance the air flow to dissipate heat ARK 1382 User Manual 18 2 2 2 ARK 1382 Rear Side External I O Connectors 2 2 2 1 DVI I Connector 2 2 2 2 ARK 1382 provides dual DVI I interface for dual independent display For VGA moni tor you can use the DVI I to VGA connector see packing list P N 1654000446 sup porting dual independent display for DVI VGA Please order the DVI I to VGA connector separately P N 1654000446 Supports CRT mode 1600 x 1200 32 bpp 85 Hz and up to 32 MB shared memory Figure 2 6 DVI I Connector Table 2 4 DVI I Connector Pin Assignment Pin Signal Name Pin Signal name 1 TMDS C2 16 HP_DET 2 TMDS C2 17 TMDS_COF 3 GND 18 TMDS CO 4 CRT DDC CLK 19 GND 5 CRT DDC DATA 20 6 MDVI_CLK 21 7 MDVI DATA 22 GND 8 VGAV
6. Status screen reports the Thermal FAN and Voltage status of the board This page depends on the particular chipset installed m Shutdown Temperature Disabled This item allow user to set the trip temperature that will notify the ACPI OS to shutdown the system m Current System CPU Temp Show Only This item displays current system and CPU temperature E 25V 33V 5V 12V and VCore Show Only This item displays current CPU and system voltage 31 ARK 1382 User Manual 3 2 9 Frequency Voltage Control NOTE This Frequency Voltage Control option controls the CPU Host and PCI frequency this section depends on the particular CPU and chipset installed some items will show up when you install a processor which supports this function m Auto Detect PCI Clk Enabled This item enables users to set the PCI Clock by system automatic detection or by manual m Spread Spectrum Enabled This item enables users to set the spread spectrum modulation 3 2 10 Load Optimized Defaults Load Optimized Defaults loads the default system values good for sta ble average operation directly from ROM If the stored record created by the Setup program should ever become corrupted and therefore unusable these defaults may be used to restore operation ARK 1382 User Manual 32 3 2 11 Set Password Note To enable this feature first go to the Advanced BIOS Features menu choose the Security Option and select either Set
7. The modular adaptable AwardBIOS 6 0 supports the broadest range of processors third party peripherals and popular chipsets including Intel CPUs from 386 through to Pentium and AMD Geode to K7 and K8 as well as nVidia and VIA processors Advantech also provides utilities to easily select and install features that suit the cus tomers own designs 3 2 BIOS Setup The ARK 1382 series has a built in AwardBIOS with a CMOS SETUP utility which allows the user to configure their required settings or to activate certain system fea tures The CMOS SETUP saves the configuration in the CMOS RAM on the motherboard When the power is turned off the onboard battery supplies the necessary power to the CMOS RAM for configuration settings to be retained When the power is turned on press the lt Del gt button during the BIOS POST Power On Self Test boot up stage this will take you to CMOS SETUP CONTROL KEYS lt t gt lt gt lt gt lt gt gt Move highlight lt Enter gt Select Item View submenu or options lt Esc gt Main Menu Quit and do not save changes into CMOS Sub Menu Exit current page and return to higher menu lt Page Up gt Increase the numeric value or make changes lt Page Down gt Decrease the numeric value or make changes lt F1 gt General help for Setup Sub Menu lt F2 gt Item Help lt F5 gt Load Previous Values lt F gt Load Optimized Defaults lt F10 gt Save all CMOS changes ARK 13
8. 0D M DIP x 2 Note RS 485 does not support Auto flow control Please refer to CH2 for jumper settings Super I O Winbond W83627HG supports m Monitoring the current CPU temperature m Monitoring the main power voltage LAN Chip Realtek RTL8111B GR Supports PCI Express 1 0a Integrated 10 100 1000 transceiver Fully compliant with IEEE 802 3 compliant Supports Wake on LAN and remote wake up Giga LAN RJ45 connector on board Audio Codec Realtek ALC203 Amplifier National LM4863 Compliant with AC97 2 3 specifications Supports to 20 bit DAC and 18 bit ADC resolution Supports Dual 2 2W Audio Amplifier Plus Stereo RCA Jack on board 3P 90D F red x 1 Right Channel RCA Jack on board 3P 90D F white x 1 Left Channel ARK 1382 User Manual 6 DVI Transmitter Chrontel CH7307C x 2 m Digital Visual Interface DVI Transmitter up to 165M pixels second m High speed SDVO 1G 2Gbps AC coupled serial differential RGB DVI inputs Complete Windows and DOS driver support m DVI hot plug detection m DVI I Connector on board DVI I Combined Conn 29P 90D F x 2 Video Amplifier Linear LT6557 x 2 m Supports Dual VGA Display via Video Separate Amplifier ver m Share with DVI I Connector on board DVI I Combined Conn 29P 90D F x 2 Battery support CR2032 Battery backup m BATTERY 3V 210 mAh with WIRE x 1 Wireless LAN Module Card WM3210 WLAN Supports Mini PCI Interface 1 0 Optional a m Supports 802 11 b g m Mini
9. 82 User Manual 22 3 2 1 Main Menu During bootup press lt Del gt to enter the AwardBIOS CMOS Setup Utility the Main Menu will appear on the screen Use arrow keys to highlight items and press lt Enter gt to accept or enter a sub menu Standard CMOS Features This setup page includes all the items in the standard compatible BIOS Advanced BIOS Features This setup page includes all the Award BIOS enhanced features Advanced Chipset Features This setup page includes all the chipset configuration features Integrated Peripherals This setup page includes all onboard peripheral devices Power Management Setup This setup page includes all the Power Management features PnP PCI Configurations This setup page includes PnP OS and PCI device configuration PC Health Status This page includes CPU overheat protection setting and reports system tem perature CPU temperature fan speeds and system voltages Frequency Voltage Control This setup page includes settings for PCI clock signal spread spectrum and CPU host SRC PCI clock speeds Load Optimized Defaults This option loads values that are optimized for stable average performance Set Password Establish change or disable passwords Save amp Exit Setup Save CMOS value settings to CMOS and exit BIOS setup Exit Without Saving Abandon all CMOS value changes and exit BIOS setup 23 ARK 1382 User Manual 3 2 2 Standard CMOS Features m Date The date format is
10. BIOS default value is set to EPP1 7 ECP Mode Use DMA 3 This item allows the user to change the DMA channel for the parallel port The BIOS default value is set to 3 m PWRON After PWR Fail Off This item allows user to select system power status after power loss 3 2 6 Power Management Setup Note This Power Management Setup screen configures the system to most effectively save energy while still operating in a manner consistent with intended computer use m ACPI Function Enabled This item defines the ACPI Advanced Configuration and Power Interface fea ture that makes hardware status information available to the operating system and communicates PC and system device information for improving power management m ACPI Suspend Type S1 POS This item allows users to select sleep state when the system is in suspend mode 1 POS Suspend mode is equivalent to a software power down S3 STR The system shuts down with the exception of a refresh current to the system memory S1 amp S3 This item is support two mode be selection by software m Run VGA BIOS if S3 Resume Auto This item allows the system to reinitialize the VGA BIOS after the system has resumed from ACPI S3 mode m Power Management Option User Define This item allows user to select system power saving mode Min Saving Minimum power management Suspend Mode 1 hr Max Saving Maximum power management Suspend Mode 1 min Use
11. LV Celeron M 423 1 06GHz 0 60C 32 140F with airflow condition Intel Core Duo ULV U2500 1 2GHz Processor 0 50C 32 122F with airflow condition Reference airflow condition 0 7 meter sec Operating Humidity 0 90 relative humidity non condensing Storage Temperature 20 70 C Storage Humidity Up to 95 60 C 9 ARK 1382 User Manual ARK 1382 User Manual 10 Chapter 2 H W Installation 2 1 Jumpers 2 1 1 Jumper Description Cards can be configured by setting jumpers A jumper is a metal bridge used to close an electric circuit It consists of two metal pins and a small metal clip often protected by a plastic cover that slides over the pins to connect them To close a jumper you connect the pins with the clip To open a jumper you remove the clip Sometimes a jumper will have three pins labeled 1 2 and 3 In this case you would connect either pins 1 and 2 or 2 and 3 The jumper settings are schematically depicted in this manual as follows A pair of needle nosed pliers may be helpful when working with jumpers If you have any doubts about the best hardware configuration for your application contact your local distributor or sales representative before you make any changes Warning To avoid damaging the computer always turn off the power supply before setting jumpers Clear CMOS Before turning on the power sup A ply set the jumper back to 3 0 V Battery On ARK 1382 User Manual
12. PCI socket MINI PCI 124P 180D F SMD x 1 7 ARK 1382 User Manual 1 3 2 Mechanical Specifications 1 3 2 1 Dimensions mm 189 x 41 x 130 6mm 7 44 x 1 61 x 5 14 CT T HD JE 0 0 M AD ANTECH EHI Sa F 78 8 O gt A o 145 4 DA ID CD Wo D UVA _ oso Detail A Figure 1 1 ARK 1382 Dimensions 1 3 2 2 Weight kg 1 15 kg ARK 1382 User Manual 8 1 3 3 1 3 3 1 1 3 3 2 1 3 3 3 1 3 4 1 3 4 1 1 3 4 2 1 3 4 3 1 3 4 4 Electrical Specifications Power Supply Voltage Voltage requirement with Adaptor 9 V 3 8 A 35 V 1 A Adaptor Power Supply Current Supply Current Maximum CPU Intel Celeron ULV423 1 06 RAM 533MHz 512GB DDR2 SDRAM Adaptor 19V DOS 0 86 A BIOS NC WINXP Idle 0 88 A WINXP HCT11 0 NC WINXP 3DMARK2001SE NC WINXP 1 16 A BURN IN TEST Suspend 0 66 A RTC Battery Nominal Voltage 3 0 V Nominal discharge capacity 210 mAh Environmental Specifications Operating Temperature The Intel Celeron is specified for proper operation when the junction temperature is within the specified range of 0 C to 100 C The Intel 945GM chipset temperature runs at a maximum of 100 C The Intel ICH7 I O Controller Hub 7 82801GHM case temperature runs at a maximum of 110 C The processor protects itself from catastrophic overheating by use of an internal ther mal sensor at a temperature level of approximately 135 C Intel U
13. SY 23 TMDS_CK 9 TMDS_C1 24 TMDS_CK 10 TMDS_C1 C1 VGAR 11 GND C2 VGAG 12 C3 VGAB 13 C4 VGAHSY 14 VCC_DVI C5 GND 15 GND Line out ARK 1382 supports left and right channel line outs 19 ARK 1382 User Manual 2 2 2 3 USB5 eSATA ARK 1382 provides an external SATA connector for external storage if you do not need to use eSATA the connector can be used as a USB port 4 3 2 i 5678 9 1011 Figure 2 7 eSATA USB Connector Table 2 5 eSATA USB Connector Pin Assignment Pin Signal name VBUS GND SATA_TX SATA_TX GND SATA_RX SATA_RX GND O O NO G R O IN gt d SALO 2 2 2 4 Power Input Connector ARK 1382 comes with a two pin header that carries 9 35 Vpc external power input ofa alo a Figure 2 8 Power Input Connector Table 2 6 Power Connector Pin Assignments Pin Signal Name 1 GND 2 9 35 Voc ARK 1382 User Manual 20 PA gl k un 4 LAA E 4 aa A ar y Y Y u fi d 6 a u i E N y d QF BIOS Operation Sections include m BIOS Introduction m BIOS Setup 3 1 BIOS Introduction Advantech provides a full featured AwardBIOS 6 0 which delivers the superior perfor mance compatibility and functionality that manufacturers of Industrial PC and Embedded boards demand its many options and extensions let you customize your products to a wide range of applications and target markets
14. e RS 422 485 you can find the jumper installation in Appendix and jumper setting in 2 12 12345 00000 OOO O 6 7 8 9 Figure 2 3 COM Connector Table 2 1 COM Standard Serial Port Pin Assignments RS 232 RS 422 RS 485 Pin Signal Name Signal Name Signal Name 1 DCD Tx DATA 2 RxD Tx DATA 3 TxD Rx NC 4 DTR Rx NC 5 GND GND GND 6 DSR NC NC T RTS NC NC 8 CTS NC NC 9 RI NC NC Note NC represents No Connection USB Connector ARK 1382 provides four USB connectors which provide complete Plug amp Play and hot swapping for up to 127 external devices The USB interfaces are USB UHCI Rev 2 0 compliant The USB interface can be disabled in the system BIOS setup Please refer to Table 2 2 for pin assignments Figure 2 4 USB Connector Table 2 2 USB Connector Pin Signal name Pin Signal name 1 VCC 2 USB data 3 USB_data 4 GND 17 ARK 1382 User Manual 2 2 1 3 2 2 1 4 2 2 1 5 2 2 1 6 Ethernet Connector LAN ARK 1382 is equipped with a Realtek RTL8111B GR Ethernet controller that is fully compliant with IEEE 802 3u 10 100 1000Base T CSMA CD standards The Ethernet port provides a standard RJ 45 jack connector with LED indicators on the front side to show its Active Link status Green LED and Speed status Yellow LED CI m ee Figure 2 5 Ethernet Connector Table 2 3 RJ 45 Connector Pin Assignments Pin 10 100 1000BaseT Signal Name TX TX N O9OUA WN Z O Compact Flash Card
15. ed and Low Speed capable Supports legacy keyboard mouse software USB dual connector on board USB conn 8P 90D M DIP x 2 USB eSATA connector on board E SATA USB 11P 90D M DIP x 1 SB Intel NH82801GHM chip supports Supports the Serial ATA specification Revision 1 0a Supports several optional sections of Serial ATA II Extensions to Serial ATA 1 0 Specification Revision 1 0 USB eSATA connector on board E SATA USB 11P 90D M DIP x 1 Note eSATA does not support PnP function SB Intel NH82801GHM chip Supports Mini PCI Interface 1 0 Supports Mini PCI WLAN extension card use only Supports 802 11A B G when use 9680005627 Mini PCI socket MINI PCI 124P 180D F SMD x 1 ARK 1382W version miniPCI is equipped with WLAN miniPCI card SB Intel NH82801GHM chip Supports ACPI 3 0 ACPI Power Management Logic Support Power connector Plug In block 2P DIP x 1 5 ARK 1382 User Manual BIOS SB Intel NH82801GHM chip Low Pin Count LPC interface support Firmware Hub FWH interface support Phoenix 4M bit Flash BIOS supports Plug amp Play APM 1 2 ACPI 1 1 socket 32 pin PLCC socket x 1 1 3 1 3 Others chipset Serial Ports Thermal sensor LAN Audio Super I O Winbond W83627HG 2 full function serial ports by Winbond W83627 Supports IRQ Sharing among serial ports on XPE COM1 Supports RS 232 422 485 via jumper setting COM2 Supports RS 232 422 485 via jumper setting COM connector D SUB CON 9P 9
16. fore the SDRAM starts a read command after receiving it m DRAM RAS to CAS Delay Auto This item enables users to set the timing of the transition from RAS Row Address Strobe to CAS Column Address Strobe as both rows and columns are separately addressed shortly after DRAM is refreshed m DRAM RASE Precharge Auto This item enables users to set the DRAM RAS precharge timing System default is set to Auto to reference the data from SPD ROM m Precharge delay tRAS Auto This item allows user to adjust memory precharge time m System Memory Frequency Auto This item allows user to adjust memory frequency to improvement perfor mance m SLP_S4 Assertion Width 1 to 2 sec This item allows user to adjust SLP_S4 signal This field indicates the mini mum assertion width of the SLP_S4 signal to ensure that the DRAMs have been safely power cycled m System BIOS Cacheable Enabled This item allows the system BIOS to be cached to allow faster execution and better performance m Video BIOS Cacheable Disabled This item allows the video BIOS to be cached to allow faster execution and bet ter performance m Memory Hole At 15 M 16M Disabled This item reserves 15 MB 16 MB memory address space to ISA expansion cards that specifically require the setting Memory from 15 MB 16 MB will be unavailable to the system because only expansion cards can access memory in this area m PEG Onboard VGA Control Auto This item allows the use
17. ght IrDA N A m GPIO N A m LAN Chipset Realtek 8111B PCI E 10 100 1000 Base T m Speed 10 100 1000 Mbps m Interface 1 x RJ45 m Standard IEEE 802 3u 100Base T Display m Chipset Intel 945GM integrated 2D 3D graphic controller m Memory Size Supports Intel DVMT Dynamic Video Memory Technology 3 0 1 MB or 8 MB under system BIOS m Resolution CRT Display mode pixel resolution up to 1600 x 1200 at 85 Hz and 1600 x 1200 at 75 Hz LCD Display mode m Display Interface 2 x DVI I VGA interface can be extended by connector m Dual Independent DVI DVI DVI VGA VGA VGA only supports clone mode 3 ARK 1382 User Manual 1 3 Chipset 1 3 1 Functional Specification 1 3 1 1 Processor CPU Processor m 1 3 1 2 Chipset Supports 533 MHz Source Synchronous Processor System Bus Supports Intel Celeron ULV423 at 1 06 GHZ CPU Supports Intel Core Duo ULV U2500 1 2GHz Processor ARK 1382 S2A1E Package 35 mm x 35 mm Micro FCBGA NB Intel 945GM GMCH chip supports D a Memory E Supports 400 533 MHz DDR2 SDRAM devices with max Supports maximum 1GB DDR SDRAM SO DIMM Socket on board 200 pin SO DIMM socket type x 1 Note There may be compatibility issues with support for 2 GB memory please check with the Advantech support team NB Intel 945GM GMCH chip supports Graphic and Video Controllers ARK 1382 User Manual Internal Graphics Features Dual display choose on board Dual DVI Dual VGA o
18. hange without notice No part of this publication may be reproduced in any form or by any means electronic photocopying recording or otherwise without prior written permis sion of the publisher All brand and product names are trademarks or registered trademarks of their respective companies Advantech Co Ltd 2008
19. he user to select the PIO or UDMA mode SATA Mode IDE The item allows the users to support IDE mode SATA Port Speed Settings Disabled This item allows the users to select SATA port speed m Onboard Device This item enables users to set the Onboard device status including enabling and disabling USB AC97 MC97 and LAN devices m Super IO Device This item enables users to set the Super IO device status including enabling Floppy COM LPT IR and control for GPIO and Power Fail status Onboard Serial Port1 3F8 IRQ4 This item allows the user to change the COM 1 address and IRQ BIOS default value suggest to 3F8 IRQ4 Onboard Serial Port2 2F8 IRQ3 This item allows the user to chang13 the COM 2 address and IRQ BIOS default value suggest to 2F8 IRQ3 UART Mode Select Normal This item allows the selection for the mode of operation of the serial port Onboard Parallel Port 378 IRQ7 This item allows the user to change the parallel port address BIOS default value is set to 378 IRQ7 ARK 1382 User Manual 28 Parallel Port Mode SPP This item allows the user to change the parallel port mode The user can choose SPP EPP ECP and ECP EPP SPP Standard Parallel Port 1 ECP Extended Capabilities Port and EPP Enhanced Parallel Port The BIOS default value is set to Normal EPP Mode Select EPP1 7 This item allows the user to change the EPP Mode for the parallel port The
20. lect Set Password again and at the Enter Password prompt don t enter anything just press lt Enter gt At the Confirm Password prompt again don t type in anything just press lt Enter gt Select Save to CMOS and EXIT type lt Y gt then lt Enter gt 33 ARK 1382 User Manual 3 2 12 Save amp Exit Setup Note Type Y to quit the BIOS Setup Utility and save user setup value to CMOS Type N to return to BIOS Setup Utility 3 2 13 Exit Without Saving Note Type Y to quit the BIOS Setup Utility without saving to CMOS Type N to return to BIOS Setup Utility ARK 1382 User Manual 34 AA g nn d T la sm NA dh g a A u U u PHE DJ G LN Gai R oa R y Wu Full Disassembly Procedure 4 1 Introduction If you want to completely disassemble ARK 1382 follow the step by step procedures below Users should be aware that Advantech Co Ltd takes no responsibility what soever for any problems or damage caused by the user disassembly of ARK 1382 Make sure the power cord of ARK 1382 is unplugged before you start disassembly 1 Unscrew the 4 screws on the bottom 2 Unscrew the 6 screws on the front panel ARK 1382 User Manual 36 3 Unscrew the screw in the middle of the front panel 4 Unscrew the 4 hex bolts on the front panel 37 ARK 1382 User Manual Unscrew the 6 screws on the rear panel J
21. lt Weekday gt lt Month gt lt Day gt lt Year gt Weekday From Sun to Sat determined and displayed by the BIOS only Month From Jan to Dec Day From 1 to 31 Year From 1999 through 2098 m Time The time format is in lt hours gt lt minutes gt lt seconds gt based on 24 hour time m IDE Channel 0 Master Slave IDE HDD Auto Detection Press Enter for automatic device detection m IDE Channel 1 Master Slave IDE HDD Auto Detection Press Enter for automatic device detection m Video The item determines that VGA display support type EGA VGA Support VGA color mode CGA 40 Support VGA color mode CGA 80 Support VGA color mode MONO Support VGA mono mode m Halt on This item determines whether the computer bootup process will stop if an error is detected during power up No Errors The system boot sequence will not stop for any error All Errors Whenever the BIOS detects a non fatal error the system will stop All but Keyboard The system boot sequence will not stop for a keyboard error but it will stop for all other errors Default value All but Diskette The system boot sequence will not stop for a disk error but it will stop for all other errors All but Disk Key The system boot sequence will not stop for a keyboard or disk error but it will stop for all other errors m Base Memory The BIOS POST displays the amount of base or conventional memor
22. nstallationN 0 oo0oooooooo 11 IE TTT 12 2 1 1 Jumper Description css eee ee eee i 12 212 JUMP SUING uses een 13 2 1 3 Locating Jumpers on the Board een 15 R c e 16 Figure 2 1 ARK 1382 Front Side External I O Connectors 16 Figure 2 2 ARK 1382 Rear Side External I O Connectors 16 2 2 1 ARK 1382 Front Side External I O Connectors 17 Figure 2 3 COM Connector een 17 Table 2 1 COM Standard Serial Port Pin Assignments 17 Figure 2 4 USB Connector eee 17 Table 2 2 USB Connector een 17 Figure 2 5 Ethernet Connector 18 Table 2 3 RJ 45 Connector Pin Assignments 18 2 2 2 ARK 1382 Rear Side External I O Connectors 19 Figure 2 6 DVI I Connector sss esse eee eee ee eee 19 Table 2 4 DVI I Connector Pin Assignment 19 Figure 2 7 eSATA USB Connector ee 20 Table 2 5 eSATA USB Connector Pin Assignment 20 Figure 2 8 Power Input Connector 20 Table 2 6 Power Connector Pin Assignments 20 BIOS Operation auvannanauvannunnunnnnuvnurnrn 1 BIOS NTN 22 BOSS SP PRE E E EO error 22 321 MEN MENU Kader 23 3 2 2 Standard CMOS Features sees eee 24 3 2 3 Advanced BIOS Features i 25 3 2 4 Advanced Chipset FeaturesS ee een 27 3 2 5 Integra
23. of this warranty as a consequence of such events Because of Advantech s high quality control standards and rigorous testing most of our customers never need to use our repair service If an Advantech product is defec tive it will be repaired or replaced at no charge during the warranty period For out of warranty repairs you will be billed according to the cost of replacement materials service time and freight Please consult your dealer for more details If you think you have a defective product follow these steps 1 Collect all the information about the problem encountered For example CPU speed Advantech products used other hardware and software used etc Note anything abnormal and list any onscreen messages you get when the problem occurs 2 Gall your dealer and describe the problem Please have your manual product and any helpful information readily available 3 If your product is diagnosed as defective obtain an RMA return merchandise authorization number from your dealer This allows us to process your return more quickly 4 Carefully pack the defective product a fully completed Repair and Replacement Order Card and a photocopy proof of purchase date such as your sales receipt in a shippable container A product returned without proof of the purchase date is not eligible for warranty service 5 Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer Part No 2006138201 Edi
24. ports 1 x Giga LAN 5 x USB 2 0 2 x DVI L Ultra Compact Fanless Embedded Box Computer ARK 1382W S0A1E Intel Celeron ULV423 1 06 2 x serial ports 1 x Giga LAN 5 x USB 2 0 2 x DVI I XPe 512MB DDR2 memory 1GB CF card Ultra Compact Fanless Embed ded Box Computer ARK 1382 S2A1E Intel Core Duo ULV U2500 1 2GHz 2 x Serial ports 1 x Giga LAN 5 x USB 2 0 2 x DVI I Ultra Compact Fanless Embedded BOX Computer ili ARK 1382 User Manual Optional accessories 1757000222 1750003222 1700001947 1700001948 1700001949 AC to DC Adapter DC19 V 3 42 A 65 W with Phoenix Power Plug 0 40 C for Home and Office Use 802 11b g 5dBi Dipole Antenna Power Cable 2 pin 180 cm USA type Power Cable 2 pin 180 cm Europe Type Power Cable 2 pin 180 cm UK Type 9666K10000E DIN Rail mounting kit for ARK 1000 series models 9666K10001EVESA mounting kit for ARK 1000 series models 1700004713 ARK 1382 User Manual Cable DVI to DVI and CRT 15cm Contents Chapter Chapter Chapter 1 A N 2 2 1 2 2 3 3 1 3 2 General Introduction 1 Tees o A 2 Product FEAT ee ee ee 3 AE Al HT 3 VDA ee 3 ENN 4 1 3 1 Functional SpecificatioN i d 1 3 2 Mechanical SpecificationSs i 8 Figure 1 1 ARK 1382 Dimensions eee 8 1 3 3 Electrical Specifications au nein een 9 1 3 4 Environmental SpecificatioNS nennen 9 H W I
25. r DVI VGA through OS Driver DVI I CRT Integrated 400 MHz Three 8 bit DACs provide the R G and B signals to the monitor Supports pixel resolution up to QXGA Supports Display Hot Plug Supports Dual VGA Display via Video Separate Amplifier DVI I DVI Supports DVI 1 0 for External Digital Monitor Supports Display Hot Plug DVI Transmitter Support Digital Visual Interface DVI Transmitter up to 165M pixels second Supports Dual DVI Display Independently WinXP Extended desktop support for Dual DVI and DVI VGA DVI I Connector on board DVI I Combined Conn 29P 90D F x 2 IDE Interface Audio Link USB Interface eSATA Interface Mini PCI Interface Power Manage ment SB Intel NH82801GHM chip supports Supports PIO IDE transfers up to 16 Mbytes sec Supports Ultra ATA transfers to 100 66 33 Mbytes sec The IDE interface integrates 16x32 bit buffers for optimal transfers Supports Compact Flash Card Type II Socket CF Socket on board CF Type II 50P 90D M external connector x 1 SB Intel NH82801GHM chip supports Supports Audio Codec 97 Revision 2 3 specification Supports Link for Audio and Telephony CODECS Supports Dual 2 2W Audio Amplifier Plus Stereo RCA Jack on Board 3P 90D F Red x 1 Right Channel RCA Jack on Board 3P 90D F White x 1 Left Channel SB Intel NH82801GHM chip supports USB host interface with support for 5 USB 2 0 ports 1 combined with eSATA All ports are High Speed Full Spe
26. r Define Allows user to set each mode individually Suspend Mode Disabled or 1 min 1 hr m Video Off Method DPMS This item allows users to determine the manner in which the monitor is blanked V H SYNC Blank This option will cause the system to turn off vertical and horizontal synchronization ports and write blanks to the video buffer Blank Screen This option only writes blanks to the video buffer DPMS Initial displays power management signaling 29 ARK 1382 User Manual m Video Off In Suspend Yes This item allows users to turn off video when entering suspend mode E Suspend Type Stop Grant This item allows users to determine the suspend type m Modem use IRQ 3 This item allows users to determine which IRQ the MODEM can use m Suspend Mode Disabled Shows the time of system inactivity before all devices except the CPU will be shut off m HDD Power Down Mode Disabled Shows the time of system inactivity before the hard disk drive will be powered down m Soft Off by PWR BTTN Instant Off This item allows users to define power button functions Instant Off Press power button to power off instantly Delay 4 Sec Press power button for 4 seconds to power off m Energy Lake Function Disabled m Wake Up by PCI card Enabled This item allows users to permit PCI cards to wake up the system from suspend mode m Power On by Ring Enabled This item allows users to permit the system to power on from a modem
27. r to select whether onboard graphics processor or the PCI Express card m On Chip Frame Buffer Size 8 MB This item allows the user to choose Frame Buffer Size BIOS default value is set to 8 MB 27 ARK 1382 User Manual m DVMT Mode DVMT This item allows the user to adjust Intel s Dynamic Video Memory Technology DVMT Bios provide three option to choose DVMT FIXED and Both m DVMT FIXED Memory Size 128MB This item allows the user to adjust DVMT FIXED graphics memory size m Boot Display VBIOS Default This item allows the user to decide bootup display mode 3 2 5 Integrated Peripherals Note This Integrated Peripherals screen controls the configuration of the P board s chipset including controls for IDE ATA SATA USB AC97 MC97 and Super IO and sensor devices this section depends on the particular chipset installed 1 m OnChip IDE Device This item enables users to set the OnChip IDE device status including enabling IDE devices and setting PIO and DMA access mode plus some new chipset support for SATA devices Serial ATA IDE HDD Block Mode Enabled This item allows the users to enable for automatic detection of optimal num ber of block read writes per sector the drive can support if IDE Hard Driver supports block mode IDE DMA transfer access Mode Enabled This item allows the user to enable the DMA transfer access On Chip Primary Secondary PCI IDE Enabled This item allows t
28. ring m USB KB Wake Up From 3 Disabled This item allows users to use a USB keyboard to wake up the system from power saving mode m Resume by Alarm Disabled This item allows users to power on the system at a specified date and or time Disabled Disable this function Enabled Enable alarm function to power on system Data of month Alarm1 31 Time HH MM SS Alarm 0 23 0 59 0 59 ARK 1382 User Manual 30 3 2 7 PnP PCI Configurations Note Use PnP PCI Configurations to set up the IRO and DMA both PnP FI and PCI bus assignments m Init Display First Onboard This item allows the user to select initial display mode optional items include PCI slot and Onboard m Reset Configuration Data Disabled This item allows users to clear any PnP configuration data stored in the BIOS m Resources Controlled By Auto ESCD IRQ Resources This item allows you to assign an interrupt type for IRQ 3 4 5 7 9 10 11 12 14 and 15 m PCIVGA Palette Snoop Disabled The item is designed to solve problems caused by some non standard VGA cards A built in VGA system does not need this function m INT Pin 1 8 Assignment Auto The interrupt request IRQ line assigned to a device connected to the PCI interface on your system m Maximum payload Size 128 The item allows user to adjust maximum TLP Transaction Layer Packet pay load size 3 2 8 PC Health Status Note This PC Health
29. stem requires password only for access to the Setup page not for bootup Default value m APIC Mode Enabled This item allows user to enable or disable Advanced Programmable Interrupt Controller APIC is implemented in the motherboard and must be supported by the operating system and it extends the number of IRQ s available m MPS Version Control for OS 1 4 This item sets the system multiprocessor specification version m OS Select For DRAM gt 64M Non OS2 Select OS2 only if the system is running OS 2 with greater than 64 MB of RAM on the system m Full Screen Logo Show Enabled Shows full screen logo during POST stage logo image can be customized m Small Logo EPA Show Disabled Shows EPA logo during system POST stage m Summary Screen Show Enabled Shows system status on Summary screen page ARK 1382 User Manual 26 3 2 4 Advanced Chipset Features Note This Advanced Chipset Features screen controls the configuration of m the board s chipset this page depends on the particular chipset installed It is strongly recommended that only technical users make changes to the default settings Va m DRAM Timing Selectable By SPD This item enables users to set optimal timings for items 2 through to 5 The sys tem default setting of By SPD ensures the system runs with stable and opti mal performance m CAS Latency Time Auto This item enables users to set the timing delay in clock cycles be
30. ted PeripheralS i 28 3 2 6 Power Management Setup eee een nn 29 3 2 7 PnP PCI Configurations anna 31 320 PC Health Status une nennen 31 3 2 9 Freguency Voltage Control eee 32 3 2 10 Load Optimized DefauliS een nen 32 32 11 Se PES VO Laden 33 3 2 12 Save amp EXIL SEP an nenne las airone 34 3 2 19 P Without SANG een 34 V ARK 1382 User Manual Chapter 4 4 1 Appendix A A 1 ARK 1382 User Manual Full Disassembly Procedure 35 Mo 36 Realtek RTL8111B 8111C Gigabit Boot Agent Configuration Menu 43 Realtek RTL8111B 8111C Gigabit Boot Agent Configuration Menu 44 vi Chapter 1 General Introduction 1 1 Introduction ARK 1382 is a fanless ultra compact system designed for a wide range of applica tions such as Point Of Information systems flight information display systems and vehicle video player system ARK 1382 is designed with Intel ULV Celeron M 423 1 06GHz Core Duo ULV U2500 1 2GHz Processor which provides excellent computing and multimedia per formance The system is equipped with 802 11b g WLAN card and supports a wide range of input voltages from 9 Vpc to 35Vpe Moreover to fit different applications ARK 1382 supports dual DVI I independent display or dual VGA with clone mode Despite the smallest size ARK 1382 still supports 5 x USB 2 0 1 x Giga LAN and 2 x COM ports user can easily install the CF card via external CF socket The
31. the Board CN15 JP8 JP3 JP6 JP4 JP5 O N o W o L mg O gu O 00 MO Hao LO _ 90 oe g pol lo ollo ollo o 00 x CD E O L LE JP7 M _ O O j O 3 O T mi Lili O Z Els HK O S lt a gt O O 00 006 000 JP1 i OO 00 OO JP2 Be OO OO OO O val og 00 o 0 O o 7 CNG 15 ARK 1382 User Manual 2 2 Connectors I MANN N C 7 J Q u L N A dE C N N Y SN A rd r WY USB4 USB2 LAN USB3 USB1 COM Figure 2 1 ARK 1382 Front Side External I O Connectors COM2 ONOFF C7 NY ho N pe ca I Z R i F CD K R CD L gt gt fav A LY af AW pew Pi Lo wD PN pet At N 7 Figure 2 2 ARK 1382 Rear Side External I O Connectors ARK 1382 User Manual 16 2 2 1 2 2 1 1 2 2 1 2 ARK 1382 Front Side External I O Connectors COM Connector ARK 1382 provides two D sub 9 pin connectors which offers RS 232 422 485 serial communication interface ports Default setting is RS 232 if you want to us
32. tion 2 November 2008 ARK 1382 User Manual il Technical Support and Assistance 1 2 Visit the Advantech web site at www advantech com support where you can find the latest information about the product Contact your distributor sales representative or Advantech s customer service center for technical support if you need additional assistance Please have the following information ready before you call Product name and serial number Description of your peripheral attachments Description of your software operating system version application software etc A complete description of the problem The exact wording of any error messages Warnings Cautions and Notes Caution A There is a danger of a new battery exploding if it is incorrectly installed Do not attempt to recharge force open or heat the battery Replace the battery only with the same or equivalent type recommended by the man ufacturer Discard used batteries according to the manufacturer s instructions Packing List Before installation please ensure the following items have been shipped Item Part Number 1ARK 1382 unit 1 Utility CD 1 Registration and 1 year Warranty card Rev A 1 2 Pole Phoenix to DC Jack Power Cable 1700001394 1 DVI I to VGA connector 1 WLAN antenna ARK 1382W version Ordering information Model Number Description ARK 1382 S0A1E Intel ULV Celeron M 423 1 06GHz 2 x Serial
33. ty by CF USB Device Select boot device priority by USB Device USB FDD Select boot device priority by USB FDD USB CDROM Select boot device priority by USB CDROM LAN Select boot device priority by LAN Disabled Do not include this device for booting Boot Up NumLock Status On When enabled the keyboard keypad boots up in number mode When dis abled the keypad boots up in cursor control mode arrow mode Gate A20 Option Fast This item enables the user to switch A20 control by port 92 default or Normal to use slower keyboard controller Typematic Rate Setting This item enables users to enable or disable typematic action When enabled they can set the two typematic controls items These fields control the speeds of Typematic Rate Chars Sec This item controls the speed at which the system registers auto repeated keystrokes The eight settings are 6 8 10 12 15 20 24 and 30 characters per second 25 ARK 1382 User Manual Typematic Delay Msec This item sets the keypress delay before typematic repetition kicks in The four delay options are 250 500 750 and 1000 Note These typematic settings apply to systems that communicate with the Tas keyboard via BIOS For Windows systems typematic settings are con E trolled by keyboard driver settings in Windows Control Panel m Security Option Setup System System requires password both for bootup and for access to the Setup page Setup Sy
34. up or System depend Va ing on what you want password protected Setup requires the password only to enter Setup System requires the password every time the sys tem boots and to enter Setup A password may be at most 8 characters long To Establish Password 1 2 3 4 Choose Set Password from the CMOS Setup Utility main menu and press lt Enter gt When you see Enter Password enter the desired password and press lt Enter gt At the Confirm Password prompt retype the desired password then press lt Enter gt Select Save to CMOS and EXIT type lt Y gt then lt Enter gt To Change Password 1 2 Choose Set Password from the CMOS Setup Utility main menu and press lt Enter gt When you see Enter Password enter the existing password and press lt Enter gt You will see Confirm Password Type it again and press lt Enter gt Select Set Password again and at the Enter Password prompt enter the new password and press lt Enter gt At the Confirm Password prompt retype the new password and press lt Enter gt Select Save to CMOS and EXIT type lt Y gt then lt Enter gt To Disable Password 1 Choose Set Password from the CMOS Setup Utility main menu and press lt Enter gt When you see Enter Password enter the existing password and press lt Enter gt You will see Confirm Password Type it again and press lt Enter gt Se
35. y installed in the system m Extended Memory The BIOS POST displays the amount of extended memory above 1 MB in the CPU s memory address map installed in the system m Total Memory This item displays the total system memory size ARK 1382 User Manual 24 3 2 3 Advanced BIOS Features Blank Boot Disabled Advantech feature enhancement When enabled the system displays a blank screen during the BIOS POST stage POST Beep Enabled Advantech feature enhancement When enabled the system emits beep sounds during the BIOS POST stage CPU Feature This item allows users to adjust CPU features CPU ratio VID Thermal and special features like XD flag Hard Disk Boot Priority This item allows users to select the boot sequence for system hard drive devices HDD SCSI RAID USB Boot Priority This item allows user to select boot sequence for USB device Boot Virus Warning Disabled This item allows users to choose or disable the virus warning feature for IDE Hard Disk boot sector protection Quick Power On Self Test Enabled This field speeds up the Power On Self Test POST routine by skipping the second third and forth re tests Default setting is enabled First Second Third Other Boot Device BIOS attempts to load the operating system from the boot devices in the order assigned First USB Device Second USB CDROM Third Hard Disk Other Enabled Hard Disk Select boot device priori
Download Pdf Manuals
Related Search