User Manual
Contents
1. WARNING The lid latch MUST NEVER be used to or move the fridge freezer CAUTION The fridge freezer should always be lifted by at least two people 6 3 Opening your fridge freezer Your Fridge Freezer has an over centre latch that provides positive pressure between the the cabinet and the seal open the fridge freezer lid Place your hand under the latch as snown in Figure Lift the latch up and away from the body of the fridge freezer The latch will pull away from the fridge freezer in an arc as shown Release the latch once it 5 clear of the fridge freezer lid Tne latch will come to rest clear of the lid as shown in Figure Place your hand under the lid finger grip and lift the lid as shown in Figure 6c To close the fridge freezer lid Position the latch on the latch stops as shown In Figure 6d Press the latch towards the body of the fridge freezer until the latch locks into place as shown in Figure 6e The latch will make a crisp clicking noise as it Closes new closed NOTE When your fridge freezer is new the latch may not fully disengage from the lid when the latch 15 lifted to its highest position Refer to Figure In this case press down gently on the lid to compress the seal slightly The latch should then become free from the lid FRIDGE FREEZER Figure Figure 6a2. the AKB Fridge Freezer warranty and service guide for details The following documents must be presented for repair and guarantee Processing of the receipt with purchase date A completed Fridge Freezer warranty claim form with the reason for the claim or a description of the fault 9 DISPOSAL Please place the packaging material in the appropriate recycling waste bins where possible If you wish to finally dispose of your fridge freezer ask your local recycling center or authorised ARB Fridge Freezer dealer for details about how to do this in accordance with the applicable disposal regulation 29 FRIDGE FREEZER 10 TECHNICAL DATA Overall capacity Connection voltage except North America 12 24 100 240 AC Connection voltage North America AZ Gane Coco Rated current en LUA a 100 240 VAC 13 07 A 14A at 120V AC Cooling capacity Weight Z7 8 515 External dimensions 508 mm x 380 mm x 705 mm IO IPIE TETEFIO T Xu Note If the ambient temperature is above 32 90 F the minimum temperature cannot be achieved Figure 18 705 380 510 E O O s B ib On CN 5 337 295 This device is CFC free The coolant circuit contains 1 34a 24 FRIDGE F
3. reduction in performance FRIDGE FREEZER 6 15 Defrosting your fridge freezer From Time TOLFETSOFT Ine Inside Or Freezer reduce both its internal capacity and its thermal efficiency recommends that you defrost your fridge freezer on a regular basis MGE the contents of the fridge freezer urn the fridge freezer Open the lid so that the ambient temperature air will cause the ice to melt Remove the drain plug and allow any water to drain from the cabinet Wipe the cabinet with a soft cloth to remove any remaining water WARNING Never use hard or pointed objects to defrost the fridge freezer or to loosen objects that have become frozen in place 6 16 Replacing the cabinet fuse Your fridge freezer is equipped with a fuse that is located in the rear of the cabinet CAUTION Disconnect the fridge freezer from all power sources before replacing the cabinet fuse TO replace Cabe mise kemove the AC and DC power leads from the power sockets Tne Insert FOI Tear Dane OF ITeezer as SNOW tn A small flat blade screwdriver be required to pry the insert away from its NOUSING Replace the defective fuse with a new fuse that has the same rating The correct ating TUSe SOCCER as 5 Iere
4. Figure 6d Figure Figure 6e SU 10 FRIDGE FREEZER 6 4 Connecting your fridge freezer 6 4 1 Connecting to 12 24V DC Your ARB Fridge Freezer can be operated on either 12V or 24V DC Your fridge freezer is fitted with a control circuit to prevent polarity reversal and possible short circuiting when the unit IS connected to a battery To connect your fridge freezer to a 12 V or 24 V DC supply Plug the 12 24 power lead into the DC power socket on the back panel of the fridge freezer as shown in Figure Connect the free end of the power lead to a 12 V or 24 V DC supply Figure 7 12 24 power socket 343322 6 4 2 12 24 V DC wiring requirements ensure optimum performance of your Fridge Freezer it is important that your wiring system Is capable of carrying the required load The accessories wiring system in many vehicles is not adequate for such a task ARB recommends that a dedicated wiring circuit be installed to power the fridge freezer This circuit should be as short as possible and be connected directly to the power supply via a 15 Amp fuse For an automotive or marine installation recommends that the wiring circuit be connected to an isolated power supply like an auxillary battery system Ihis will prevent discharge of the main starting battery For cable lengths up to 6m recommends a minimum cable diameter of 6 mm For cable lengths greater than 6m
5. When using the DC output from your generator a battery of correct voltage 12 or 24V must be connected between the generator and the fridge freezer fridge freezer should be turned off when starting and stopping your generator CAUTION Some engine driven generators are not suitable for powering your fridge freezer FRIDGE FREEZER 6 5 Cable clips Your ARB Fridge Freezer has clips on the rear panel of the unit to retain both the DIE 1005740 V AG Cables Ne Cable are sized The cables supplied with your fridge freezer Tne left hand cable clip shown in Figure is lor trie 100 240 AG Cable 1 naria Cis Tor ine 2 24 v DIC TOD Figure 10a Figure 10b C c 100 240 12 24V cable cable clip ee install the cable Into the cable clips Plug the power cable into the correct power socket Refer to section 6 4 end Closest DFeSS the Cable IMO ING Cabie CiIDSs USING a rotating action he rotating action will help slide the cable under the clips NOTE Care should be taken when installing and removing the cables to prevent damaging the body of the fridge freezer or the power cables WARNI
6. FRIDGE FREEZER OPERATING AND SERVICE GUIDE 1 BEDIENUNGS UND SERVICEANLEITUNG 28 Ces gt DE USO Y MANTENIMIENTO 54 MANUEL DE L UTILISATEUR 80 Cit GUIDA ALL USO ALLA MANUTENZIONE FRIDGE FREEZER FRIDGE FREEZER Please read this operating and service guide carefully before starting your AKB Fridge Freezer for the first time This quide should be kept in a safe place together with your warranty and service guide and a copy of your receipt CONTENTS INTRODUCTION ET 3 2 SUPPLY DETAIES 3 3 SAFETY INSTRUCTIONS utei n coc 4 i T 7777 222 4 4 4 INTRODUCTION TO YOUR ARB FRIDGE FREEZER 5 5 BINS AEA FION 2 N 6 5 6 0 SX MERO DP 1 CLO Ral Manilla scr 6 OPERATION Nee E SS 9 6 X Y 7 Du eg 2 o oo 7 OU COMACCING VOU MCGEE EZET eatis tea oq EEUU URN REA ERREUR SUME 2 m OWE SOCK EET io Da COR
7. ARB recommends that you consult a qualified technician for advice on the correct cable diameter FRIDGE FREEZER 6 4 3 12 24V DC power socket The plug on your 12 24 DC power lead has a removable adaptor collar With the collar in place as shown in Figure this plug will fit into a conventional vehicle accesories power socket cigarette lighter With the adaptor collar removed as shown in Figure amp b this plug will fit into a 2 pole auxiliary power socket These sockets are commonly referred to as Merit or Hella sockets Figure Figure amp b Adaptor collar Adaptor collar IN place removed highly recommends that this 2 pole connection be used for all 17V DC and 24V DC connections of a fridge freezer This will provide a positive and secure connection between your power source and your fridge freezer following points should be considered when choosing a location for your fridge freezer auxiliary power socket qostormtaepower sockebas close To te TAGE Teezer asJ4s Practical Position the power socket in a convenient location that will allow the user to easily connect and disconnect the plug from the socket Positioned the power socket in a protected location away from dust and moisture Position the socket high in the vehicle to prevent it from becoming wet should the vehicle Ingest water NOTE the plug is removed and the fridge freezer is hard wired into 12V or 24V DC circuit
8. of experience and Knowledge unless they nave been given supervision or instruction concerning use of the appliance by a person responsible for their safety If your power cable 5 damaged it must be replaced before the fridge freezer 5 used Disconnect your fridge freezer from all power supplies before cleaning or maintenance Do not store flammable liquids or gases in or near your fridge freezer Do not open or tamper with the refrigerant circuit DO MOLTEMOVE OF elecqgcar components Do not store or transport caustic or solvent based material in the fridge freezer Do not use your Fridge Freezer if there are visible signs of damage Only Mave YOUR tecer serviced oy xen dutnerseg ARB Freezer Service Agent Safe operation of the fridge freezer For safe operation of your fridge freezer ARB recommends that you take note of the following safety points Ensure that there is always sufficient ventilation around the fridge freezer to prevent overheating Refer to section 5 1 for details Do not touch the internal metal shell of the fridge freezer with a wet hand Do not place your fridge freezer near naked flames or other heat sources heaters camp fires gas ovens direct sun light Do not fill your fridge freezer cabinet with ice or fluid JO NOL DISICe eiectr ICa deviees VOU TTIOOS Ir eezer Protect your fridge freezer from rain and moisture Do not use your fridge free
9. placed between the fridge freezer cabinet and lid to ensure that the lid remains open Care must be taken to ensure that this temporary does not damage the cabinet id or seal 22 FRIDGE FREEZER 7 CLEANING AND MAINTENANCE To clean the inside or outside of the fridge freezer Use a damp cloth and warm water containing a mild non abrasive nousenold detergent If your fridge freezer is operated dusty conditions recommends that you clean the outside surfaces on a regular basis to prevent the build up of dirt and grit In particular recommends tnat you routinely clean around the hinge mechanisms and the motor surround clean around the motor surround recommends placing the fridge freezer in a well ventilated area and using a vacuum cleaner or a smeam or Comor essed WARNING Under no circumstances Is the motor surround to be removed Please take note of the following points before cleaning your fridge freezer Always turn off power and remove the plugs from the fridge freezer before cleaning or servicing the unit Never use hard objects or abrasive cleaning agents to clean the fridge freezer Do not use brushes scouring pads or hard or pointed tools to defrost the fridge freezer Do not clean the fridge freezer under running water or with a high pressure washer 8 GUARANTEE YOUR ARB Frage FICeZer S covered Veal FiGase TO Your
10. to a solid base or fridge slide One threaded insert is Se Centre OP each or e TEDUSIP JARBCORECORFIRHIEDOS SEDIS mounting if the fridge freezer is to be permanently mounted If your fridge freezer will be removed on a regular basis please refer to section 5 7 7 temporary mounting permanently mount the fridge freezer Position the fridge freezer on the mounting surface at the desired location and mark the outline of the cabinet rage Ireezer angd mark the cabinet centre 16 shown as point C in Figure 5a Mark and drill four 6 5 mm holes in the mounting surface using the diagram Figure 5a as a guide To make use of the drain plug mark and drill one 13 hole in the mounting surface at point C as shown Figure 5 Remove the bolt from the centre of each of the four rubber feet using a hex as shown in Figure 5b Ensure that the rubber feet remain in the base of the cabinet Position the fridge freezer on the mounting surface so that the drilled holes line UD with the threaded Tr Ine cabinet Attach the cabinet to the mounting surface using bolts as shown in figure 5c Do not exceed the fastener assembly torque of 3 5 Nm 2 5 when tightening the bolts ARB recommend apply no permanent thread sealant to the bolts NOTE The rubber feet must be fitted between the base of the cabinet and the mount
11. 15 Amp inline fuse must be included in the circuit FRIDGE FREEZER 6 4 4 Connecting to 100 240V AC Your Fridge Freezer can be operated on an AC voltage of 100 240V The fridge freezer has a priority circuit which gives priority to mains AC power over DC power If Ie 1S oe UML VV On tne AG Supply NOTE The red LED may light up briefly when the supply voltage 15 switched between AC and DC connect your fridge freezer to 100 240 V AC supply Plug the 100 240 V power lead into the AC power socket on the back panel of Tee feac Figure 9 100 240 power socket FRIDGE FREEZER v CAUTION Never handle the plugs leads or switches with wet hands or while standing on a wet surface CAUTION If you are operating your fridge freezer from 100 240 V supply a residual current circuit breaker must be installed the circuit ARB advises seeking advice from a trained technician 6 4 5 Connecting to an engine driven generator Please take note of the following points before connecting your ARB Fridge Freezer to an engine driven generator generator must be fitted with an automatic voltage regulator It must supply a standard pure sine wave AC voltage without fluctuation In voltage TeQguency eg Or Z
12. MECUNG To SE N Re 6 5 E 4 VG scc pP 15 Ores STIG Sedis EOM TERT 16 6 9 16 em 16 T SS MEN CI PIER OE C 12 MENS Rol UST E 20 ON wen tt ate ete ett 20 OA DIU 2 21222220 e pu 22 SN 22 7 CLEANING AND 23 8 GUARANTEE EE 23 9 DISPOSA 23 R7 nt 24 TROUBLESHOOTING ced 25 FRIDGE FREEZER 1 INTRODUCTION Congratulations on purchasing an ARB Fridge Freezer Your Fridge Freezer has been specifically designed for tough off road conditions and is suitable for both cooling and freezing foods By following the instructions and guidelines listed in this document you will ensure that you receive maximum performance and long term reliability out of your new fridge freezer FreeZer Is Operate Of a DC or z4 v WG SUDDIV vehicle boat or caravan It can be operated fr
13. NG The cable clips are sized for the cables supplied with your fridge freezer ARB does not recommend using other cables these cable clips 6 6 Energy saving advice To help you achieve the optimum performance from your fridge freezer ARB makes the following recommendations Place the fridge freezer in a well ventilated area which 15 protected from direct sunlight Try to minimise the frequency with which the fridge freezer 15 opened Do not leave the lid open for longer than necessary Avoid setting the target temperature unnecessarily low Defrost the fridge once starts to form FRIDGE FREEZER 6 7 Lid removal The lid on your ARB Fridge Freezer can be guickly and easily removed and refitted TOsremove Weezer Wa te mage or Une td Or Tage cabinet as shown in Figure 11a The procedure for opening the fridge freezer lid Grip the lid firmly with both hands Pull the lid towards the front of the fridge as shown in Figure 11b The hinge pins will release and the lid can be removed from the fridge freezer cabinet Figure 114 Figure 770 gt 2 um 3 1 n A IE 2 gt HINT If you are finding It difficult to remove the lid apply a small sideways force to the lid as you pull it forward This will help to
14. REEZER 11 TROUBLESHOOTING The following checklist will nelp to identify the source of the problem with your fridge freezer If after carrying out this checklist you are still unsure of the cause of the fault please contaccyour Neal est ARE Fridge Freezer 7 The fridge freezer has stopped operating The power LED does not glow 1 1 The power lead connections could be loose or dirty at the fridge freezer or power supply end Check that the fridge freezer power lead connections have not become loose or disconnected heck that the electrical contacts nave not become dirty and are preventing full voltage flow to the fridge freezer 1 2 The fuse in the 12 24V DC cable plug may have blown Check the TZ Z4 WC Cable Dig Tuse ang 1 10 SECO hus 1 3 The cabinet fuse may have blown Check the cabinet fuse and replace if necessary Refer to section 6 16 2 The fridge freezer compressor has stopped operating The power LED 15 ORANGE 2 1 The fridge freezer has reached the desired target cabinet temperature he fridge freezer is operating correctly No action is required 3 The fridge freezer has stopped operating The power LED 15 OFF and the RED error LED Is flashing 3 1 The internal battery protection system has caused the fridge freezer to switch off because the battery voltage is low The freezer will automatically restart once the restart volt
15. age Is reached Refer to section 6 11 for switch off and restart voltages 4 The fridge freezer does not cool or has stopped operating The power LED Is green 4 1 There may be an internal fault within the fridge freezer This can only be repaired by an authorised Fridge Freezer Service Agent 5 The control panel displays an error message eg and the fridge freezer does not cool 5 1 Thefridge freezer may have switched off due to an internal fault This can only be repaired by an authorised Fridge Freezer Service Agent FRIDGE FREEZER 6 When connected to a vehicle wiring circuit with the vehicle running the fridge freezer occasionally shudders or stops operating 6 1 Itis likely that there is loss of voltage occurring within your vehicle wiring This can be confirmed by taking a voltage reading at the end of the power lead for the fridge freezer If the reading 15 below 12 4 volts you should have the wiring system checked If necessary upgrade your fridge freezer wiring circuit using the information in section 6 4 as a guide 7 The fridge freezer stops and starts or runs erratically 7 1 Theinternal battery protection system may be causing the fridge freezer to switch off because the battery voltage is low Check whether the voltage supply at the fridge freezer plug has dropped below the shut down voltage listed section 6 1 1 The voltage must be read at the fridge freezer plug as there is
16. connect the fridge freezer from all power sources before replacing the light bulb the light bulb the basket 5 fitted with its high side against the front of the fridge it must be removed to provide access to the light housing Refer to section 6 12 for details Remove the transparent light housing from the internal case of the fridge freezer as shown in Figure 1 a To do this place your finger under the lip of the light nousing and pry It away from the internal case of the fridge freezer Replace the defective light bulb with a new bulb of the same rating as shown Figure 1 6 Replacement bulbs can be purchase from your nearest ARB Fridge Freezer service agent Ensure that the LEDs inside the bulb are facing the transparent face of the light NOUSING Test that the light functions correctly Refit the light housing into the cabinet of the fridge freezer Figure 17a Figure 17b Light housing Light bulb Ne Bulb holder rT Y E 6 19 Storing your fridge freezer If you are storing your freezer for an extended period of time makes the following recommendations Switch the freezer off and disconnect it from all sources of power Remove all items except the basket and basket divider from within the cabinet Leave the lid slightly open to allow airflow through the cabinet HINT A soft piece of foam or rubber could be
17. dislodge one of the hinge pins TOI Position the lid on top of the cabinet with the hinge pins lined up with the pin recesses as shown in figure 11 The lid must be slightly inclined to ensure that TIOEeOr Bed ISxclesr cabinet Push the lid towards the back of the cabinet so that the hinge pins slide into the recesses as shown in Figure 11 Pe ninge DINS Will COME Te Tecesses WIEN sa Crisp click Open and close the to ensure that both hinge pins are correctly seated Close the latch by following the steps described in section 6 3 Figure 11 c Figure 774 FRIDGE FREEZER 6 8 Turning the fridge freezer on or off TO TON vOUF AIRS Freezer onm Pressand hold for between two and three seconds When tne freezer is on the power LED will light up green The display will show the current cabinet temperature NOTE The current cabinet temperature reading of the temperature at the centre of the cabinet temperature at other areas of the cabinet can deviate from this DET TO t rm tne Trage Teezer Ol Press and hold for between two and three seconds When the fridge freezer is off the power LED and the display will go blank 6 9 Setting the target cabinet temperature To set the target cabinet temperature of your ARB Fridge Freezer On once to displa
18. e battery fully charged FRIDGE FREEZER To change tne battery protection level Turn tne freezer 5 three times to display current battery protection setting er to change tne battery protection voltage between High Medium nEd and Low 10 After 5 to 6 seconds of Inactivity the display will flash twice and return to displaying the current cabinet temperature High Medium Low 6 12 Making use of the basket Your Fridge Freezer 15 supplied with a reversible wire basket that nelps to protect the internal walls of the fridge freezer cabinet he basket can be installed with the high side of the basket against the front of the fridge as shown in Figure 12a This allows long items to be laid across the top section of the fridge freezer cabinet Tne basket can De Teposmonmned Some teen We shown in Figure 125 This provides a full height divider between the main cooling cabinet and the dairy fruit cabinet Figure 12a Figure 12b 74 NP Se eee High side High side of basket of basket To remove the basket from the cabinet Lift the basket vertically out of the fridge freezer cabinet To reinstall the basket into the cabinet Slide the basket down into the cabinet of the fridge freezer he basket Is correctly positioned when i
19. gure 4 Control panel FRIDGE FREEZER E F G Power ON OFF Button eedem Error Indication LED Function Button Digital Temperature Display Temperature Up Button Change setting Temperature Down Button Change setting down gt D E E G The power LED 5 green when the compressor is running The power LED is orange when compressor Is not running eg when the freezer has reached its target ternperature 5 INSTALLATION General installation The following points should be considered when choosing a location to install your A minimum clearance of 50 mm must be maintained on all sides of the fridge Whether the installation is permanent temporary the fridge freezer must attached to secure anchorage points The ideal mounting position for the fridge freezer is on a flat horizontal surface If the fridge freezer is subject to sideways angles eg heal on a boat it withstand a sideways angle of 30 Avoid placing the fridge freezer near sharp or hot objects Avoid placing the fridge freezer near loose objects that could fall on the cabinet and obstruct its operation Never operate the fridge freezer near flammable liquids or vapours FRIDGE FREEZER 5 2 Installing in a vehicle 5 2 1 Permanent mounting Your ARB Fridge Freezer has four threaded inserts in its base that can be used to permanently mount the cabinet
20. ing surface NOTE If longer bolts are required M6 x 1 0 high tensile socket head cap screws with a minimum grade of 8 8 must be used To avoid damaging electrica components within the fridge the bolt length must only be Increased by the thickness of the mounting surface dimension A in Figure 5a plus 8 mm to allow for the recess the rubber feet NOTE When removing the M6 bolts avoid turning the fridge freezer on its side 5 2 2 Temporary mounting steel handle at each end of your Fridge Freezer has been engineered to be used as a titedown point recommends that the tle down system be used to Securely MOUNTING FRIDGE FREEZER Figure 5a Base of fridge freezer Mounting Surface Drain plug Front of Thickness of mounting surface mage Teezer lt Dimensions in mm Hex key Figure 5c Mounting surface OF THICKNESS A mm Rubber mounting foot Mounting bolt 1 FRIDGE FREEZER 6 OPERATION 6 1 Before use BEOR starting your IndGge Weezer the DE Cleaned Inside and Our with a damp cloth Please refer to the chapter Cleaning and maintenance for further details on maintaining your fridge freezer 6 2 Carrying your fridge freezer Your Fridge Freezer is supplied with a powdercoated steel handle at each end of ne These
21. nitor settings If your fridge freezer can operate without the vehicle ignition being on the battery monitor will cause the unit to switch off as soon as the supply voltage falls below the set level he fridge freezer will automatically restart once the restart voltage Is reached NOTE When the battery monitor 55 active the cooling unit including compressor will not run The power LED on the control panel will be OFF and the error LED will flash RED The cooling unit will not restart until the voltage level of the battery reaches the restart voltage listed in Table 1 Table 1 BATTERY MONITOR MODE HIGH Switch off voltage 12V DC 11 8V Restart voltage 12V DC Switch off voltage 24V DC LOW Restart voltage 24V DC 2309 26 2 V iT your ridge Ireezer IS connected 10 Starling battery Ona 12 27 System ANB recommends that the battery monitor level be set to HIGH If your fridge freezer is connected to an auxiliary battery on a 12 24 DC system recommends that the battery monitor level be set to LOW If your fridge freezer is connected to AC mains power recommends that the battery monitor level be set to LOW NOTE ARB recommends that the battery be charged once the battery monitor has been triggered ARB also recommends that all non essential electrical equipment that draws power from the same source as the fridge freezer be turned off until th
22. normally at least one to two volts lost between the power source battery and the fridge freezer plug vehicle battery may need replacement or the wiring to the fridge freezer may need to be upgraded Refer to section 6 4 for details on wiring 8 The fridge freezer is running too long and Is not cooling properly 8 1 Good fridge freezer performance especially in hot ambient temperatures is dependent on good air flow around the fridge freezer cooling slots Check that all ventilation slots are unobstructed and there is enough clearance for good airflow around the fridge freezer Refer to section 5 1 for details 9 When the fridge freezer lid is open the LED cabinet light does not come 9 1 The fridge freezer may not be connected to a suitable power supply Check the connection between the power source and the fridge freezer 9 2 The LED light bulb may have blown andl M MeCes sary neler 10 The lid latch does not disengage from the fridge freezer during opening 10 1 The high quality lid seal may be raising the lid slightly and preventing the latch from releasing ress GOWN Genuy On 1O COMpIess Ine Seal AOG De DeCOMmMe Tee KONT The Nd FRIDGE FREEZER 22
23. om a 100 240 AC mains supply using the power inverter CAUTION If you wish to cool medicines please check if the cooling capacity of the fridge freezer Is adequate for the purpose 2 SUPPLY DETAILS Your Fridge Freezer has been delivered with the following items If any of these items have not been included with your fridge freezer please contact your local Freezer dealer ITEM QUANTITY keversiDle Dasket kermovable basket divider power Cable 00 240V power Cable PINE FICEZEF GUTE 7 7 Friage Freezer warranty and service DookKlet FRIDGE FREEZER 3 SAFETY INSTRUCTIONS 3 1 General safety For the safety of all people who will use your fridge freezer ARB recommends that you take note of the following general safety points 3 2 Always apply the correct voltage to the fridge freezer with the correct polarity Do not connect your fridge freezer to a battery charger AC DC converter or rectifier Disconnect the fridge freezer from the battery before using a high speed battery charger Do not use sharp abrasive or corrosive materials to clean or defrost the fridge Children snould be supervised to ensure they do not play with the fridge freezer This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack
24. r Lo 15D Replace the fuse insert back into its housing Figure 15a Figure 15b Cabinet Fuse insert 20 FRIDGE FREEZER 6 17 Replacing the plug fuse 12 24 Your fridge freezer is equipped with a fuse that is located in the 12 24V Dc plug CAUTION Disconnect the fridge freezer from all power sources before replacing the plug fuse the DIU TS 2 If fitted remove the plastic adaptor collar from the end of the plug as shown in Figures 16a and 166 do this twist the collar and then pull it from the plug Remove the single screw as shown In Figure Separate and remove the top housing from the body of the plug Remove the contact pin from the end of the plug as shown in Figure 16d Replace the defective fuse with a new fuse that has the same rating The correct rating for the fuse is 8 Amp 32 Reassemble the plug by reversing the steps listed above Figure 16a Figure 166 Figure 16c Figure 16d Remove Contact pin YES L l a E TN 5 9 Fuse bo c FRIDGE FREEZER 6 18 Replacing the light bulb Your fridge freezer is equipped with a long life and low current draw LED light bulb Under typical operating conditions this bulb snould not require replacement In the unlikely event that you need to replace the light bulb please follow the procedure outlined below CAUTION Dis
25. ts base Is in contact with the base of the fridge freezer cabinet 19 FRIDGE FREEZER 6 13 Basket divider Your Fridge Freezer 5 supplied with a removable basket divider hls divider can be easily removed by lifting it vertically as shown in Figure 13 When refitted it Is important that the basket divider is located between the ribs on the sides of the wire basket Figure 13 Location ribs for A basket divider Removable AND NN gt basket divider OXY NY SEH 6 14 Drain plug Freezer nas a Temovable Crain Plug Base ine cabinet ds shown Figure 14 The drain plug be removed to drain liquid from the cabinet of the fridge freezer Figure 14 ___ 56 Drain plug To remove the drain plug Open the lid of tne fridge freezer Grip the drain plug with your fingers Gently lift the drain plug away from the base of the cabinet To refit the drain plug OF ine Locate the tip of the drain plug in the drain Apply gentle pressure to the drain plug so that It slides into the drain drain plug Is correctly located when the lip of the drain plug makes full contact with the base of the cabinet NOTE It is important that the drain plug is refitted before the fridge freezer is run for an extended period of time Failure to do this will result in
26. y current cabinet target temperature SS tO MScEedse tie target temperare 71695 to decrease the target temperature one degree Continue pressing or until the desired target cabinet temperature Is reacned After 5 to 6 seconds of Inactivity the display will flash twice and return to displaying the current cabinet temperature NOTE When the target temperature reached Will stop running the LED Will Change to orange 6 10 Changing between and Your Fridge Freezer is capable of displaying temperature in either degrees Celsius GeGrees Fanrennell change the display between and urn the fridge freezer on Press twice to display current temperature unit setting Press Dewwvesr Gane T After 5 to 6 seconds of Inactivity the display will flash twice and return to displaying the current cabinet temperature 16 FRIDGE FREEZER 6 11 Using the battery monitor Your ARB Fridge Freezer is fitted with a battery monitor to control the level of discharge of your battery battery monitor has three setting HIGH MEDIUM and LOW When set to HIGH the battery monitor will provide maximum protection for the battery against excessive discharging When set to LOW the battery monitor will allow maximum use of the energy stored the battery Table snows the voltage cutout levels for the three battery mo
27. zer if you suspect that the electrical system has been exposed to water Do not use your fridge freezer if it has been immersed in water FRIDGE FREEZER 4 INTRODUCTION TO YOUR ARB FRIDGE FREEZER Ine Key components YOU ARB Fridge Freezer below In Figures tO Figure 1 Front of fridge Figure 2 Rear of fridge 16 17 18 19 20 21 Lid latch 12 Compliance plate and Control panel serial number Front carry handle Motor surround Powdercoated zinc steel cabinet 12 24 power socket deber Tee 23220 WC cable Lid Reversible Basket Cabinet fuse LED cabinet light 100 2407 AC SOCKET Drain plug 100 240 AC cable clip Removable basket divider 0 Lid stop Main cooling cabinet Rear carry handle Dairy Fruit cooling cabinet UJ O SIGS Um sib 6 FRIDGE FREEZER The dairy fruit cooling cabinet of your ARB Fridge Freezer is designed to maintain a temperature that is warmer than the main cooling cabinet This makes It an excellent to store selected items like dairy products frult vegetables and chocolate 5 1 Fi
Download Pdf Manuals
Related Search