user and maintenance manual - restoranu.eu Konsultacijos
Contents
1. 3 mm screw a low nut left hand thread onto the motor shaft then screw on the flexible coupling 11 Dismantling the receiver part knives 1 With a thick cloth hold the knives BE CAREFUL there is a risk of cutting yourself 2 With pliers catch the rigid coupling and unscrew it clockwise left hand thread 98133 US 4 3 12 2010 AA www santos fr Q santos J Assembling the receiver part knives Fig H With a thick cloth hold the knives BE CAREFUL there is a risk of cutting yourself 2 Fit the low nut 19 left hand thread into the hexagonal housing of the hard plastic coupling 12 3 Adhering to this order put the knives 15 back on the shaft the thin stainless steel washer 16 then the fiber washer 17 and finally the wide stainless steel washer 18 4 Screw up the coupling 12 counter clockwise left hand thread TROUBLESHOOTING Identifying the cause of appliance stoppage with precision The appliance does not start e Check the mains supply the condition of the supply cord 10 The appliance stops after the motor has overheated the motor unit is hot The motor is protected by a built in cut out system If it overheats the motor stops e Turn the On Off switch 9 to position 0 take out the plug 98133 US 4 3 12 2010 AA www santos fr e Wait for the motor to cool down 20 to 45 minutes then turn the On Off switch 9 on position 1 If the problem persis2. 50 60 Motor Power rating Power input Speed Position 2 Position 1 14000 Bowl capacity Dimensions Height Width Depth Net weight Packaged weight 1 These ratings are given for your guidance The exact electrical specifications of your appliance can be found on the rating plate 2 Noise level measured with sound pressure appliance in operation 1 m from its centerline in accordance with standard EN 31201 98133 US 4 3 12 2010 AA www santos fr Wiring diagram 110 120V 50 60Hz On Off 3 positions Green Yellow IHA 98133 US 4 3 12 2010 AA www santos fr Wiring diagram 220 240V 50 60Hz Black Black onot 3 positions DQ XU Blue Blue White kid Brown Brown INTERFERENCE FILTER Green Yellow lt lt 98133 US 4 3 12 2010 ay www santos fr ITEM Description 1 Bowl assembly Motor unit Lid Cap Bowl nut Knife hub 2 3 4 5 Bowl 6 7 8 Bowl seal 9 On Off switch 10 Power supply cord 11 Flexible coupling 12 Hard coupling 13 Groove of motor shaft 14 Motor shaft 15 Knife shaft 16 Thin stainless steel washer 17 Fiber washer 18 Wide stainless steel washer 19 Low nut 98133 US 4 3 12 2010 AA www santos fr QS santos J WARRANTY CERTIFICATE WARRANTY Since the 01 01 95 all our appliances comply with CE and possess the CE label Our guarantee is
3. 0 position before connecting the power cable plug to your mains electric power socket 98133 US 4 3 12 2010 a www santos fr QS santos J USING FOR THE 1 TIME Thoroughly clean all parts in contact with the food Fig A e Take off the lid 3 and the cap 4 and wash them with a standard dish washing product e Unscrew the bowl 5 from the nut 6 turning it counter clockwise right hand thread Fig B e Being careful not to injure yourself with the sharp knives remove the knife hub 7 and the bowl seal 8 Fig C e Wash with a standard dish washing product or in the dish washer the lid 3 the cap 4 the knife hub 7 the 98133 US 4 3 12 2010 AA www santos fr SS santos j bowl seal 8 and the bowl 5 RECYCLING THE PRODUCT AT THE END OF ITS SERVICE LIFE This appliance has the recycling symbol marking relating to waste electrical and electronic equipment This means that this product must be processed by a waste sorting system in accordance with Directive 2002 96 CE WEEE Professional Equipment section so that it can be either recycled or disassembled in order to reduce any impact on the environment For further information please contact your dealer or SANTOS For the disposal or recycling of the appliance components please refer to a specialist company or contact SANTOS Electronic products which have not been out sorted are potentially dangerous for the environment
4. SANTOS SAS 140 150 AVENUE ROGER SALENGRO 69120 VAULX EN VELIN LYON FRANCE PHONE 33 0 472 37 35 29 S OS FAX 33 0 478 26 58 21 ANT E Mail santos santos fr www santos fr BAR MIXER N 33 USER AND MAINTENANCE MANUAL IMPORTANT documents included in this manual to be kept CE COMPLIANCE DECLARATION e WARRANTY CERTIFICATE Coffee grinders Fruit juicers Mixers Blenders Drinks dispensers Planetary mixers Cheese graters Ice crushers Mincers Vegetable slicers Dough mixer Moulins a caf Presse fruits Mixers Blenders Distributeurs de boissons Batteurs melangeurs P trin Rapes fromage Broyeurs gla ons Hache viande Coupe l gumes MODELES DEPOSES FRANCE ET INTERNATIONAL INTERNATIONALLY PATENTED MODELS 98133 US 4 3 12 2010 VN www santos fr CONTENTS CE COMPLIANCE DECLARATION aa 3 IMPORTANT SAFEGUARDS srsisicsissintcscvesiessssesessdaveviccssdtnsasidsvanesedlssatsddtecensasenvavedsvvenvedeyesudnns 4 DO NOT ne one KAB ANAN anodin non 4 ELEC TRIGAL CONNECTION a EAA eee estate 4 USING FOR THE 1 TIME nananana nsanssnaransusasunsannmmsann 5 RECYCLING THE PRODUCT AT THE END OF ITS SERVICE LIFE ee 6 YOUR BAR MIXER NGBB NAA AA AN KO GAN AA 7 Using the MIXER AA AA 7 STARTUP AANGAT AA GANA E E 7 CLEANING Sn EE E E E denied 8 STORAGE aoe e mou eee a AY 8 DAVIN TIEN AGE da datent ones 9 Spare ONS eiere aE a EE N EDEA abs eSEE EEEE A AEAEE 9 Changing the coupling S
5. The packaging material should be disposed of or recycled in accordance with regulations in force 98133 US 4 3 12 2010 AA www santos fr Q santos J YOUR BAR MIXER N 33 e The bar mixer N 33 is designed especially for bars caf s hotels restaurants cocktail bars canteens stores selling fruit juices cake stores ice cream parlors e The appliance comprises a cast aluminum motor unit and a removable mixing bowl This is made up of a transparent plastic graduated bowl a plastic lid a measuring cap a set of stainless steel knives and a coupling system e The mixer N 33 is designed to mix different foodstuffs in the form of liquids doughs or solids e Itis ideal for making o drinks fruit vegetable cocktails punches syrups sangria o small quantities of soup sauces souffl s pur ed vegetables meat and fish pates creams stewed fruit o Ice creams milk shakes Using the MIXER START UP ATTENTION a mixer must always be used with a minimum of liquid in the bowl Assembly and preparation 1 Place the knife hub 7 into the bowl nut 6 2 Fit the bowl seal 8 onto the knife hub 7 making sure that the seal is seated properly on the knife hub ATTENTION It is important to duly adhere to the assembly order of the elements to prevent serious malfunctioning of the appliance adhere to 6 7 8 5 fig C 3 Screw and tighten the bowl 5 onto the bowl nut 6 until it is s
6. YET nn 9 Assembling the drive part motor Fig F 10 Dismantling the receiver part knives 11 TROUBLESHOOTING am NAA dd an ee E EER 12 The appliance does not SAN eatoeenn 12 The appliance stops following an overload mmaaasanususawwaaaaaaananasansanaaaaaannanans 13 The motor runs but the knives do not rotate 13 TECHNICAL SPECIFICATIONS suisses ANA ABA AA 14 Wiring diagram 110 120V 50 00N7 umasa Ba a NAB nn us 15 Wiring diagram 220 240V 50 60H Z anna aaa aaa aa 16 WARRANTY CERTIFIGATE Ses aboseronamesmemaamammaananens 18 APPLIANCE IDENTIFICATION PLATE sonne nanasa 18 98133 US 4 3 12 2010 AA www santos fr CE COMPLIANCE DECLARATION THE MANUFACTURER SANTOS sas 140 150 Av Roger SALENGRO 69120 VAULX EN VELIN LYON FRANCE declares that the appliance intended for the professional market described below Description BAR BLENDER Type number 33 33C complies with e the statutory provisions defined in appendix 1 of the European machines directive n 2006 42 CE and the national legislation transposing it e the statutory provisions of the following European directives and regulations o N 2006 95 CE low voltage directive N 2004 108 CE EMC directive No 2002 95 CE RoHS directive No 2002 96 CE WEEE directive N 1935 2004 CE regulation relating to materials a
7. ced at the current rate A preliminary estimate can be supplied Coffee grinder not using SANTOS original burrs are not taken under guarantee The warranty conditions repairs reconditioning of the espresso coffee grinder are the object of a specific note Our guarantee does not extend to the payment of penalties the repair of direct or indirect damages and notably to any loss of income resulting from the nonconformity or the defectiveness of products SANTOS s global responsibility being limited to the sale price of the delivered product and to the possible repair of the defective products In case of revelation of an imperfection during the warranty period the Distributor has to unless a different written agreement of SANTOS indicate to his customer to stop any use of the defective product Such a use would release SANTOS of any responsibility APPLIANCE IDENTIFICATION PLATE SPECIMEN For all the documents not delivered with the appliance Printed Faxed Downloaded 98133 US 4 3 12 2010 18 18 www santos fr
8. ealed by compressing the bowl s seal 4 Fit the bowl assembly 1 onto the motor unit 2 with the motor stopped switch 9 in position 0 checking the bowl assembly is seated as per the diagram opposite 5 Fit the lid 3 with its cap 4 onto the bowl 5 6 Check that the on off switch 9 is in position 0 before plugging in the power cable a ANTOS S SANTOS rel A 98133 US 4 3 12 2010 WRONG POSITION RIGHT POSITION 10 to the mains power socket 7 Add a minimum of liquid or pur e until the knives are completely covered before adding the solid ingredients to be mixed For best results dice up the solid ingredients and insert them through the hole in the lid when the knives are rotating 8 Select the knife rotation speed depending on the work desired Switch to position 1 for low speed 12 000 rpm Switch to position 2 for high speed 16 000 rpm 9 Switch off the appliance by setting the on off switch to position 0 ATTENTION It is important not to remove the bowl assembly 1 or to fit it before the motor is stopped COMPLETELY to prevent remature wearing of the coupling system CLEANING IMPORTANT e In all cases stop the appliance and unplug the power cable 10 e To avoid injuring yourself when cleaning handle the knife hub and the knives carefully e The appliance should neither be cleaned in a jet of water nor with a high pressure spray e The motor unit 2 must
9. nd articles intended to come into contact with foodstuffs O O O O Harmonised European standards used to give presumption of conformity with the essential requirements of the above mentioned directives e NF EN 12852 A1 2010 Food processing machinery Food preparation equipment and blenders Safety and hygiene requirements This European standard is a type C standard as defined in EN ISO 12100 When the provisions of this type C standard differ from those stated in the type A or B standards the provisions of the type C standard override the provisions of the other standards This standard provides the means to comply with the requirements of the machines directive n 2006 42 CE see appendix ZA e NF EN ISO 12100 1 and 2 2004 Safety of machinery General principles for design e NF EN 60204 1 2006 Safety of machinery Electrical equipment of machines General requirements e NF EN 1672 2 2005 Food processing machinery Basic concepts Hygiene requirements e NF EN 60335 1 2003 Household and similar electrical appliances Safety e NF EN 60335 2 64 2004 Particular requirements for commercial electric kitchen machines Drawn up in VAULX EN VELIN on 01 01 2010 Signatory s position CHIEF EXECUTIVE OFFICER Signatory s name Aur lien FOUQUET Y a f Signature Cf 98133 US 4 3 12 2010 AA www santos fr IMPORTANT SAFEGUARDS When using cleaning or maintaining the machine always follow these i
10. not be immersed in water You are advised to clean the appliance as soon as it has finished being used It will be easier to clean if you do not allow the remaining scraps of food to dry in the bowl lid or on the knives Although the bowl assembly 1 can be washed in a dish washer without being dismantled for optimum hygiene you are advised to dismantle the bowl assembly 1 and wash all the components separately bowl nut 6 bowl seal 8 knife hub 7 bowl 5 lid 3 and cap 4 The base and outside of the motor unit should be cleaned with a soft damp sponge then dried STORAGE e To prevent cuts you are advised to replace the knife hub 7 back into the bowl 5 and the bowl nut 6 e Do not fit the lid of the bowl airtight when the appliance is stored away This machine requires no particular maintenance because the bearings are lubricated for life 98133 US 4 3 12 2010 8 18 www santos fr If any intervention is necessary to replace parts subject to wear such as the knives the electrical or other components please refer to the parts lists see the exploded view at the end of this manual MAINTENANCE Prior to carrying out any intervention on the appliance it must be disconnected from the mains without fail 10 Spare parts This machine requires no particular maintenance because the bearings are lubricated for life If any intervention is necessary to replace parts subject to wear such as the knives
11. nstructions Read all instructions Note You will find it easier to understand the next few paragraphs if you refer to the diagrams at the end of this manual DO NOT 1 Never operate the appliance when it is empty 2 Do not use this appliance to crush big ice cubes or frozen foods The knives are not meant for this 3 Do not insert dry ingredients into the mixer before switching it on 4 Do not remove the lid before the appliance has stopped completely 5 Never remove the bowl assembly 1 from the motor unit before the motor has stopped COMPLETELY 6 Never fit the bowl assembly 1 onto the motor unit 2 when it is in operation ELECTRICAL CONNECTION e The appliance s power supply is available in two single phase voltages 110 120 V 50 60 Hz 220 240 V 50 60 Hz Line protection the appliance must be connected to a standard 2 pole earth socket The set up must be fitted with a differential circuit breaker and a 16A fuse The appliance must be earthed TAKE CARE e Before connecting the machine check that the mains electrical voltage is the same as the voltage for your appliance Its value is shown gt either on the identification plate under the machine gt oron the identification plate on the last page of this manual e If the power cable is damaged it should be replaced with a special unit available from SANTOS or a SANTOS approved dealer TAKE CARE Check that the On Off switch 6 is in the
12. of 24 months from the manufacturing date mentioned on the descriptive plate except concerning the asynchronous motors consisting of a rotor and a stator which are warranted for 5 years from their manufacturing date Warranty is strictly limited to the free replacement of any part of origin recognized by us as defective due to a defect or building default and identified as belonging to the concerned appliance Warranty does not apply to damages resulting from installation or use non complying with our appliance data sheet users manual or in case of an evident lack of maintenance or disrespect of elementary security electric rules It does not apply in case of regular wear and tear Any replacement of parts under warranty will be realized after return of the defective part in our workshops postage paid supported by a copy of a conformity statement on which appears the serial number of the appliance Every appliance is equipped with a descriptive plate conforming to the EC recommendations and of which a duplicate exists in the conformity statement serial number manufacturing date electrical characteristics In case of serious damage judged repairable only in our workshops and after prior consent from our departments any appliance under guarantee is sent by the Distributor carriage paid In case of repairs or reconditioning of appliances not under guarantee the round trip transport is payable by the distributor The parts and workforce are invoi
13. the electrical or other components please refer to the parts lists see the exploded view at the end of this manual For all spare part orders state gt the type gt the machine serial number and gt the electrical specifications recorded under the machine Changing the coupling system IMPORTANT Fig D e The drive part motor 11 is made of flexible rubber e The receiver part knives 12 is made of hard plastic Dismantling the drive part motor Fig E 98133 US 4 3 12 2010 AA www santos fr 1 2 3 4 SS santos J Lay the motor unit down on its side Stop the rotation of the rubber drive part You can use the knife hub 7 fitted with the rigid coupling 12 Use a thick cloth to hold the knives to prevent you from getting cut Via the central hole of the base plate put a flat ended screwdriver into the groove of the motor shaft 13 Turn the screwdriver clockwise to unscrew the motor coupling left hand thread Assembling the drive part motor Fig F 1 Fit the motor unit 2 onto its legs 2 By hand screw the flexible coupling onto the motor shaft 14 anti clockwise left hand thread 98133 US 4 3 12 2010 ay www santos fr Depending on the model of the motor shaft you may sometimes have to screw a low nut onto the motor shaft before screwing on the flexible coupling Fig G e f D is greater than 3 mm do not screw on a low nut e f D is less than
14. ts switch off the power supply to the machine unplug the power supply cord 10 and call in the maintenance service or contact a SANTOS approved dealer The appliance stops following an overload If the motor jams foreign body matter or food too hard jamming the knives it may heat up very quickly and cut out due to overheating e Switch off the appliance unplug the power supply cord 10 e Switch the on off switch 9 to position 0 e Remove the bowl assembly 1 from the motor unit 2 and place it on a work top e Remove the lid 3 from the bowl and with a long thin object shift the hard bits jamming the knives e Put back the bowl assembly 1 onto the motor unit and switch back on e If the knives get jammed again empty the bowl and cut the food up into small pieces If the problem persists switch off the power supply to the machine unplug the power supply cord 10 and call in the maintenance service or contact a SANTOS approved dealer The motor runs but the knives do not rotate e Check the seating of the bowl assembly 1 on the motor unit 2 Fig 1 e Check the condition of the coupling system 11 and 12 e Check the bowl seal 5 is positioned correctly see assembly and preparation part S SANTOS z NG WRONG POSITION RIGHT POSITION 98133 US 4 3 12 2010 AA www santos fr TECHNICAL SPECIFICATIONS ELECTRICAL SPECIFICATIONS 1 Model 33 Single phase Frequenc Hz 50 60
Download Pdf Manuals
Related Search