Molift AS - Meditec Medical
Contents
1. C This should be tak en into consideration when transporting the lifter and therefore keeping it in a temper ate part of the vehicle Alternatively the lifter must rest in a temperate room until the equip ment has achieved proper working tempera ture If defects or faults occur The lifter must be switched off immediately if one of the following conditions occur e damage to electrical devices or cables or damage to parts of electrical insulation e damage or failure on safety devices Q If the lifting movement does not start when the corresponding button is pressed please consult the fault finding table in the mainte nance chapter to locate the fault Injury to personnel or equipment may occur 1f Molift PARTNER 230E is used in an incorrect man ner and if e covers are removed by unauthorised personnel e used incorrectly e insufficient maintenance Page 4 of 24 e load exceeds maximum limit The maximum load stated in this manual and on the lifter is the maximum load e unauthorised repair of electrical devices or cables Lift and transfer AN The patient lifter may tip over if used incor rectly Ignorance of warnings and instruc tions may lead to personnel injury Read in structions carefully before attempting to lift anyone The Molift PARTNER 230E has a Safe Work ing Load on 230 kg meaning that it is tested and approved for lifting of patients up to 230 kg A Several factors have to be considered du2. Easy lifting slings are as the name indicates easy to use They are washable at 80 C and auto clave at 85 C for 30 minutes It is recommended to use Molift slings Slings from other manufacturers may have other specifications leading to unexpected insta bility and possible personal injury aT Fold the sling as indicated above before use The grey side should be facing away from the user when putting the sling in place The sling should be held by one hand leaving the other free to move and sup port the user Torn cut frayed or broken slings can fail resulting in serious injury to the user Use slings in good condition only Destroy and discard old unusable slings molift designed for life molift PARTNER Please read the user manual that comes with the sling for specific user instructiond O Sling without head support Page 11 of 24 molift PARTNER Lift and movement to and from bed Lift from bed Roll user onto her side Put the folded sling behind her back The centre of the sling should be parallel with the users spine Roll her then onto her back Pull the leg loops forward and under the thighs as shown in illustration above Cross the loops one through the other Page 12 of 24 If the user has a bed which enables raising and lowering it should be lowered before the lifting starts O Position the legs under the bed with the suspension over the user Be
3. drives us at Molift The company was started 20 years ago by a man who through his own experience saw the need for lifting and moving patients in an effective and comfortable way for both patient and carer We have since then delivered products that compliment the natural movements of the body that is both simple and intuitive to use Products designed to give the patient a better life in addition to providing the carer with real support and optimum work enjoyment This is the true meaning of Molift designed for life Molift AS Ole Deviksvei 44 N 0668 OSLO Norway Telephone 47 4000 1004 Fax 47 4000 1008 www molift com info molift com
4. faults or omissions on its part within the scope of the warranty obligations stated in the purchase contract Claims for damages are exclud ed irrespective of the legal reason from which such claims are derived Only documentation belonging to the actual equipment is valid Any failure to comply with the safety regulations and precautionary measures stated in these operat ing instructions renders the declaration of conform ity supplied with the system in accordance with Council Directive 93 42 EEC concerning medical devices invalid Page 3 of 24 molift PARTNER Safety precautions General Before putting a Molift PARTNER 230E into opera tion the operator must ensure that the lifter and ac cessories are in good working order especially with regards to safety All instruction and information in this manual regarding safety and general precau tions must be read understood and followed care fully Any disregard to these precautions may result in personnel injury or damage to the equipment The lifter must be taken out of service immediately or not returned to use if faults and or irregularities that may have influence on the safety are discovered Safety devices and equipment must not be removed disabled or in any other way altered A Molift PART NER 230E shall only be used when all safety devic es and equipment is 1n place and fully operational ES The lifter is designed for use in room tem perature 10 to 40
5. if you are using a sling with head support Otherwise as described above Page 14 of 24 Lift and transfer to and from wheel chair Lift and transfer from wheel chair Fold the sling as described in Using lifting slings The gray side should be turned away from the user when placing the sling an a Gi E f If the users physique and ability allows it the user should be encouraged to take active part in fitting the sling The user can lean forward lift her thighs and help placing the leg section O Lean the user forward gently but ensure you con tinue to support her Place the folded sling behind the user s back and push it down until it touches the seat of the chair The leg sections of the sling are pulled forward and beneath the user s thighs by the loops The loops are then crossed one through the other as shown Molift Partner 230E E Rev B2 11 2006 Pay close attention to your actions Ensure that all four loops of the sling are securely fastened to avoid the user slipping or falling Move the lifter around the chair and let the user rest her feet on the chassis A Lift raise the user above seat height and perform the transfer It is not necessary to lift the person very high If the transfer is from a wheelchair the brakes must be locked to prevent the wheel chair from rolling away Lift and transfer to wheel chair Manoeuvre the lifter so that the user i
6. pension the suspension shall be used diago nally i e loops from the sling shall be fas tened on hooks diagonally opposite Pay close attention to your actions Ensure that all four loops of the sling are securely fastened to avoid the user slipping or fal ling Try to position the user as low as possible prefera bly resting the feet on the chassis when transferring the lifter with a suspended user In this way the cen tre of gravity will be as low as possible and there fore reducing the risk of instability The lifter should be manoeuvred with spread legs in outer position to achieve the highest possible stability Be careful during movement the suspended user may swing somewhat during turns stops and starts Be particularly careful when manoeuvring close to furniture to prevent the suspended user from collid ing with these objects Molift Partner 230E E Rev B2 11 2006 The lifter shall not be used to lift or move us ers on Sloping surfaces Avoid deep pile carpets high thresholds uneven surfaces or other obstacles that may block the cas tors The lifter may become unstable if forced over such obstacles increasing the risk of tipping over The lifter shall only be used for movement over short distances It is not a replacement for wheelchair or similar Use of spread legs Use wide legs wherever appropriate for instance to position the lifter around wheelchairs toilets etc Using lifting slings The
7. 3033000 No head support With head support Art no 3005050 Art no 3006050 Art no 3032100 Art no 3033100 Art no 3032200 Art no 3033200 Art no 3032300 Art no 3033300 2 Art no 3032400 Art no 3033400 Easy Toilet Sling and Basic Bathing Sling for kids Art no 3032500 Art no 3033500 see the tables below size XXS and XS Molift Easy Toilet Sling Comfort Size Nohead support Separate head support Molift Easy Sling Molift Basic Sling Molift Easy Amputee Sling Molift Basic Bathing Sling molift Page 17 of 24 designed for life molift PARTNER Sling size guide Easy and Basic Slings Recomm Color cod weight Kg XXL wate 230 300 86 730 6e ms fee 1 L Green 90 160 66 100 6 Ss Red 2550 51 75 jeo xs igntbve 7 25 f 46 fes 5s xs Pink ar a s 56 Choice of sling size depends on both user weight and shape size of user Bag for slings Part no 3048000 Padding for suspension Part no 1330114 Page 1 8 of 24 Molift Partner 230E E Rev B2 11 2006 Maintenance Daily maintenance Com Detergents must be pH neutral Do not use solvents or strong liquids this may damage surfaces on the lifter and change the quality of the material For disinfection when need ed use isopropyl alcohol Avoid abrasive or etching cleaning products Clean surfaces with a damp cloth using an appropri ate detergent Make sure that there is no damage or cr
8. acks on supporting parts The suspension shall not be used if there are any visible damages or cracks as it may cause personal injury or damage to the lifter Monthly maintenance e Check the lifter and the suspension especially for damage Make sure there is no loose parts on the lifter e Remove hair and pile from the castors and verify that the castors rotates without abnormal friction e Verify that the contacts of the hand control is firmly in place and that the battery fits correctly in the battery holder e Clean contact and hand control with spirit or similar to remove grease and dirt e Verify that the cables for the hand control and charger are intact e Run the lifter up and down and legs in and out to verify that it runs normally and without any abnormal noise Service yearly maintenance Molift Partner 230E has a LED on the battery holder indicating if the lifter needs service The LED gives a green light when the lifter is ready for use The electronics has a power save function which makes the system sleep after a while with no activi ty All lights will go out Activate the system by pus hing one of the buttons on the hand control molift designed for life molift PARTNER The electronics logs how much the lifter is being used and the load it is used with After a given time of usage there will be given a signal that the lifter needs service to the service LED The LED will first give a yellow lig
9. andard 4 point suspensions Q Easy Toilet sling is a toilet sling with a thick er and wider upholstery It is also available with head support The Molift Easy Toilet Comfort sling is easier to fit in narrow en vironments and is available with a separate head support The toilet sling can be washed at 80 C and 1s fitted as follows e Insert the sling behind the users back with the grey side away from user e Fasten the belt firmly around the user s body e Place the leg section under the front part of the thighs and pull the loops up between the thighs On Molift Easy Toilet Comfort place the leg section over and down between the thighs and pull outwards from the inner part of the thighs Page 16 of 24 The leg sections of Molift Easy Toilet Comfort Sling are fitted to separate the legs therefore they should not be crossed as the other Easy slings O e Hook the four loops on the suspension as for oth er slings e Position the lifter around the toilet and lower the user e Pull the leg sections out of the way The sling can be left on during bathroom use Alternative By pulling the leg sections from the outside and in you will achieve a wider leg posi tion O Molift Partner 230E E Rev B2 11 2006 molift PARTNER Accessories Molift Easy Toilet Sling fti ji No head support With head support m eng Art no 3032050 Art no 3033050 Molift Easy Paediatric Sling Art no 3032000 Art no
10. at the date of purchase limited to 3 months after the production year week The extended warranty 1s offered in addition to the local sale of goods act It is mandatory that the product undergoes safety control and maintenance performed by an authorised service partner at least every 12 months according to this service manual made by Molift AS e Yearly maintenance and safety control must be performed within a maximum interval of 12 months and for the first time maximum 12 months after date of purchase or maximum 15 months after year week of production e Molift AS will cover the cost of spare parts and labour in the warranty period for all necessary re pairs caused by product defects that can be traced back to manufacturing The repair must be perfor med by an authorised service partner or at Molift AS own workshop during the warranty period e All warranty repairs must be approved by your Molift supplier or by Molift AS prior to the repair e The owner of the product is responsible for establishing the service agreement and the cost for the annual safety control and maintenance e The service manual has one page for every 12 months containing checkpoints for maintenance and safety control The extended warranty is valid only with signature and or stamp by authorised service partner including service partner s signed label with authorisation no on product Normal warranty is 12 months This still applies for slings hand control batter
11. careful not to lower the suspen sion too low touching the user Make sure that the suspension is centred over the user before you start the lifting Remember the castors should not be locked When all four loops are hooked onto the suspension raise the user carefully Pay close attention to your actions Ensure that all four loops of the sling are securely fastened to avoid the user slipping or falling If the user is in a hospital bed it will help to raise the head of the bed O Repositioning of the user may be needed to ensure that a safe and comfortable sitting position is at tained as the user is raised Reposition using the handle on the back of the sling Molift Partner 230E E Rev B2 11 2006 Raise the user until the buttocks are just above the mattress Lift the user s legs and turn her so she fac es the lifting column When clear of bed and if prac tical lower the user so that her feet rest on the chas sis If possible lower the bed before lifting Move the lifter away from bed Beware of obstructions under the bed that can cause castors to stop or tip Lift to bed Raise the user until the buttocks are just above the mattress Position the lifter under the bed Beware of obstructions under the bed that can cause castors to stop or tip Take care not to squeeze the users legs designed for life molift PARTNER Centre the user over the bed and turn her him so that the feet poin
12. d two buttons for adjusting the adjustable legs In addition there 1s a green diode which illuminates when the battery needs charging Battery LED Spreading legs Lift down Emergency stop and lowering Emergency stop All of the Molift patient lifts are equipped with emergency stop and lowering The emergency stop button is situated on the battery holder Push the red button to cut the power to the motor Turn the but ton clockwise until it pops up to reset the emergen cy stop Page 9 of 24 molift PARTNER Emergency lowering It is possible to perform an emergency lowering in case of a general malfunction Molift Partner 230E has both an electrical and manual emergency low ering Electrical lowering Electrical emergency lowering is placed on the bat tery holder Push the button and hold until the pa tient is lowered Manually lowering Allen wrench There is an allen wrench situated on the top of the column for the purpose of manually lowering Push the allen wrench through the hole on the top of the column and turn until the patient is lowered down Com Contact the Molift service partner if the rea son for the failure causing an emergency low ering is unknown or if it is a result of failed components or parts Page 10 of 24 Lift and transfer The suspension shall always be positioned across the user as shown left in the illustration below When using slings intended for two point sus
13. ding the use of the lifter Carefully read the manual before using the lifter in order to be familiar in the function and use of the lifter Explanation of symbols This symbol is used to point out instructions and information related to work place safety where injury may occur if the information is disregarded or ignored Follow these instruc tions be careful and attentive at all times This symbol indicates important information regarding the use of the equipment If not taken into consideration it may lead to dam age or functional defects to the lifter or other equipment This symbol indicates important and useful information If taken into consideration it will help the operator of the lifter to work ef ficiently It may help simplify routines and to explain complicated facts O Before using the patient lifter Before using a patient lifter the operator must be trained accordingly Practice lifting a colleague and be lifted by others It is important not only to know how to move another person using the lifter but also how it is to be lifted Try out and practice using all the relevant slings for the different types of lifter and movement you may encounter Before lifting a per son you should explain the procedure When using the lifter it s also important to use the correct sling and accessories according to e type of disability e size e weight e type of movement molift designed for life molif
14. ent from Molift AS Operating the hand control ccc00cce0e 9 Exciting laws conventions and agreements Emergency stop and lowering 0000088 9 protects all documents No extract of this do Lift and transfef ocen 10 cumentation can be reproduced used or trans Use of spread legs 0 ccccccceeeseceeeeeeeeeeees 11 Jerred without prior written consent from Molift Using lifting SINGS cccecceccsccseceseeseeseeseeseeee 11 AS Violation of these regulations may lead to Lift and movement to and from bed 12 judicial repercussions and economic responsi Lift and transfer to and from floor 13 bility Industrial rights are reserved Lift and transfer to and from wheel chair 14 Q E BQO rreren Errera EER 15 ia 112110 e P ENEA E EE E 16 Accessories eerren 17 i j Lifting SHING cccccccecccecccecececcceeeeneeaneeaeeeanees 17 designed for life Maintenance ccececceceeeeeeeeeeteeeeeeteeeee 19 Molift AS Daily MAINTENANCE eeeceeeeceesecetseeeeteeeteees 19 Ole Deviksvei 44 Monthly maintenance cccccccceeeeneeee eens 19 0668 OSLO Norway Service yearly Maintenance 19 Teleph 47 40001004 www molift com TrOUDIOSHOOTING 0 cecceccecceseeseeseeseeseeseeee 20 Fax 47 40001008 info molift com Page 2 of 24 Molift Partner 230E E Rev B2 11 2006 General advice This user manual contains important safety instruc tions and information regar
15. ht then red Take contact with your local service representative and order service If the re is a Sound together with the light 1t means the lif ter needs service immediately Service LED Servicelamp Status No light Ready for use Yellow Order service lifter still works Red Perform service Perform service im mediately Flashing yellow Overheating If the lifter is run up and down constantly for a lon ger period the electronics may be overheated and the lifter will stop The service LED will flash un til the lifter is cooled down enough for further use The service LED will go out when the lifter is ready for use Red sound If you are not able to solve the fault or problems by yourself using this manual please contact local aut horised service representative If you do not know whom to contact locally please contact your dealer or Molift AS to get help Page 19 of 24 molift PARTNER Molift recommends yearly service on the lifter Ser vice is done by an authorised service representati ve according to procedures in the technical manual The service partner uses the Molift Service Tool to read the data from the lifter and for logging service and resetting the service LED The owner is respon sible to ensure proper logging and written verifica tion performed by authorised service partner Troubleshooting If you have access to other similar lifters it might be an advantage to switch par
16. ies and paint Gj vik 28 08 2006 Molift AS Geir Olav Farstad Managing Director Page 22 of 24 Molift Partner 230E E Rev B2 11 2006 molift PARTNER molift DECLARATION OF CONFORMITY CE Molift AS Ole Deviksvei 44 0668 OSLO NORWAY Telephone 47 40 00 10 04 hereby declare that Molift PARTNER 230E patient lifter and that the accessoires used only together with this product Year 2006 are in conformity with e The Council Directive concerning medical devices 93 42 E F and according to this classified as medical equipment class 1 Molift PARTNER 230E is manufactured in conformity with the following national or international standards that also might implement a harmonised standard e 15010535 Hoists for the transfer of disabled persons Requirements and test methods e ISO 14971 Medical equipment Risik analysis Notified fody Title Managing Director Name Geir Olav Farstad Company MoliftAS 28 08 2006 p Lat p L 2 nia V as Date a Signature v Page 23 of 24 molift designed for life At times with increasing demand for efficiency in the healthcare sector and growing focus on patients needs it is easy to neglect the needs of the carer The need to give better help and caring avoiding heavy lifting situations avoiding putting your own back at risk without being completely exhausted after work and still have some sur plus energy when the workday 1s over This 1s the insight that
17. lamp which gives a signal when the lifter needs service Manual emergency lowering and allen key Drive handle ke 7 A Handcontrol e I q h Battery f LA Battery holder Emergency stop Chassis Page 5 of 24 molift PARTNER Technical data Weight totally excl battery 40 kg incl battery 41 5 kg Material Steel aluminium and composite plastic Motor 24V DC Battery 26 4 V NiCd 1 9 Ah Molift PowerPac Number of lift with fully charged battery 75 lifts 75 kg 50 cm 1902 1175 11 Page 6 of 24 Safe Working Load SWL 230 kg Lifting height 1275 mm Lifting speed 30 mm sec 75 kg Height of legs 110 mm Measurements 1175 x 700 x 1902 mm LxBxH Measurements in illustrations below are in millime tres 1958 u Molift Partner 230E E Rev B2 11 2006 Assembly disassembly To be able to operate the Molift Partner 230E the operator must have good knowledge of the lift in cluding assembly disassembly and preparation be fore use Assembly and use of charger The charger shall be connected to the power outlet at all times It is possible to mount the charger on a wall surface or place it on a table Molift AS tests and charges all batteries be fore packing and shipment However all bat teries must be charged before use Unpacking e The lifter comes in one cardboard box Verify that the box has no apparent damage If dam aged check
18. molift PARTNER2Z30E a I cw CE a patient lifter from l cx ex C ja r aial n molift designed for life molift PARTNER Table of Contents General advice 3 Explanation Of symbols ccccceeceeeeee ences 3 Before using the patient lifter 006 3 Responsibility sees ocisccosucetiacenuteteedetuenestutcnatdcuevtins 3 Safety precautions cc cece cece eens 4 CUA EEE E E E uote teunceauvoue 4 If defects or faultS OCCUF cccccceece seen eeeees 4 Lift and transfert ooann 4 About the product 0 cece cc ceeeeeees 5 Main Plt ccc ccc cccceccc cece eec eee eeeceeeaeeaeeeaeenees 5 Safety AOVICES ccccccccecccceeccececeeseeeeseeesaees 5 Technical data cc cccceccccccceceseesseeeeeeeeees 6 Assembly disassembly 05 7 Assembly and use Of Charge 0 cc0006 T UNPACKING saciesas 7 IMPORTANT PASS CUMIN ecg breemnsnbedammateemmawsaecesemacusaeresecerieates T Checklist before USe nnnennnenennnneea 8 The patient lifter is only meant to be used by Disassembly 8 qualified personnel Operation cc ccceeccecccccccccecceeeeeeeeeeeeeenanaaens 9 The manual shall not be handed over or made Battery Care ANd charging 1 ccceeeeeeee anes 9 available to any unauthorised third party wit Battery Capaci ersinnen 9 hout a prior written cons
19. o hand con trol has disconnected recon nect contact Hand control has failed test with another hand control and change if defective contact lo cal representative for service Defective control electronics change control electronics contact local representative for service Motor is defective change mo tor contact local representa tive for service Molift Partner 230E E Rev B2 11 2006 lift Page 21 of 24 designed for life molift molift WARRANTY Molift AS hereby declares that this product is awarded up to 5 five year extended manufacturer s warranty It is very important to our customers and to Molift AS that our products meet all relevant quality and sa fety requirements according to both customer and authority demands Molift AS develops and manufac tures products with high standards of safety quality and design and we are continuously in a process of keeping our products in position among the market leaders To make our products quality level more explicit Molift AS have introduced extended warranty time on all of our patient lifters A 5 five year warranty against defects which might be traced back to ma nufacturing 1s offered The extended warranty period is offered under the condition that the regulations described here are completely fulfilled and that the product has been used according to its intentions The extended warranty is valid for a period of 5 five years starting
20. rgency stop is activated during storage for safety reasons Page 8 of 24 Molift Partner 230E E Rev B2 11 2006 Operation Battery care and charging Molift Partner 230E is supplied with a battery with a 26 4 V cell unit that 1s placed in the battery holder on the lift A charger is also supplied to charge the bat tery whenever needed The charger can be mounted on a wall surface or placed on a table The charger has a LED Light Emitting Diode indi cating the status of the battery as described below Charger LED Place the battery in the charger After a few seconds the LED will change from yellow to orange indicat ing that the battery is charging When the LED gives a constant green light the battery is fully charged Battery capacity A Battery LED 1s situated on the battery holder on the lift If the voltage of the battery falls below a cer tain level the diode will change to orange indicating the need for charging There is still enough capacity to perform 3 5 lift cycles 75 kg at this point molift designed for life molift PARTNER If the battery is discharged during a lift it is always enough power to lower the user down again O goe Battery Battery LED Servicelamp Electrical emer gency lowering Emergency stop EA Contact for hand control Operating the hand control The hand control to Molift Partner 230E has four buttons two buttons for up and down an
21. ring move ment of the lifter e the user shall sit as low as possible facing the lifting column e the user should rest their feet on the chassis Stand to the side of the user when lifting Ensure that arms and legs are clear of the lift chair bed etc Try to maintain eye contact with the user this will help the user feel safe and comfortable Pay close attention to your actions Ensure that all four loops of the sling are securely fastened to avoid the user slipping or falling Use the drive handles when manouvring the lifter do not push or pull the patient suspen sion or lifting arm Do not touch the underside of chassis or bet ween chassis and legs when monouvring the legs Molift slings shall ONLY be used to lift per sons NEVER use the sling to lift and or move objects of any kind Molift Partner 230E E Rev B2 11 2006 About the product Molift Partner 230E is a mobile lifter intended for lifting and transferring persons The lifter is made out of light materials it has castors electrical ad justable legs and a battery It is therefore ideal for use in institutional care Main parts The lifter is built around a chassis unit comprising a lifting column fixing unit rear castors and spread ing mechanism for legs The adjustable legs are op erated by an electrical motor and gives the operator a possibility to adjust the width of the lifter to differ ent needs and situations On the lifting column there i
22. s a drive handle and a battery holder On the battery holder there is a connection for the hand control and an emergency stop button On the lifting column there is a trolley on which the lifting arm is attached The suspension is attached to the lifting arm and the suspension rotates freely allowing the Molift PARTNER 230E to be used at any angle Lifting arm Suspension _ a Trolley with rubber protection Lifting column m f Control electronics incl service lamp battery lamp and electrical emergency lowering Legs molift designed for life molift PARTNER Safety devices Molift PARTNER 230E is equipped with several safety devices which are intended to prevent dam age to personnel and equipment in the case of incor rect use e The lifter has an overload sensor preventing the lifter to be operated with more than 230 kg e The lifting arm is hinged to prevent the arm and suspension from squeezing the patient if it is lowered too much The lifting arm will not pro duce any force when moving downwards e The suspension has safety hooks to prevent the sling loops to fall off e When activating the emergency stop button the power supply will be disconnected and the lifter will stop e If an error occurs on the lifter it is possible to lower the lifting arm electrically on the battery holder or manually by operating the emergency lowering switch on top of the column e The lifter has a service
23. s as far back in the wheel chair as possible A When lowering you can use the following tech niques or a combination of them to position and get the user seated far back in the chair If the transfer is from a wheelchair the brakes must be locked to prevent the wheel chair from rolling away e push gently on the knees e pull the loop on the back of the sling e tilt the chair slightly backwards Lower the user into the chair unhook sling from suspension and remove the lifter molift designed for life molift PARTNER Removal of sling Gently pull leg section to the side out from the us er s thighs Standing by the side of the user lean her forward supporting with one hand Pull sling up from behind her back Pulling sharply on sling may cause user to fall forward resulting an injury Always sup port the user by keeping one arm around the user s Shoulder when fitting or removing the sling see illustration If the users physique and ability allows it the user should be encouraged to take active part in fitting the sling The user can lean forward lift her tights and help placing the leg section O Bathing The procedure for lifting to from the bath is in prin ciple the same as for to from bed A special bathing sling is used for this purpose This sling dries quick ly and may be washed at 80 C Page 15 of 24 molift PARTNER Toileting The Easy Toilet Sling is used with the st
24. sible to hang it on the drive han dle or the plastic hooks on the column e Place the battery in the holder with the connec tors facing down Release the emergency stop and run each function of the lifter a couple of times without load to verify proper function Molift AS tests all lifters with and without load before shipment The control is an extra precaution to uncover any shipment damage and or incorrect assembly Page 7 of 24 molift PARTNER Checklist before use e Check that the lifter has no apparent damage or other faults especially that the suspension has no damage or cracks e Ensure that the lifting arm and lifting column are properly fixed and that there 1s no loose parts on the lifter e Check that the emergency button is deactivated and that the lifter works e Check that you have sufficiently charged batter ies to complete the task you have planned e Check that the servicelamp gives a green light indicating it is ready for use If the servicelamp gives a yellow or red light the lifter needs serv ice Make sure that the suspension has no dam age or cracks and that the lifting arm and column is properly fixed before use Disassembly e Remove the battery e Remove the lifting arm with rubber protection by pulling the locking handle up and forwards while lifting the lifting arm e Release the lock handle on the chassis and then lift off the lifting column Q It is recommended that the eme
25. t PARTNER Responsibility Please read these operating instructions carefully before putting the product into operation We as sume no liability for damage or malfunctions re sulting from failure to comply with the instruc tions Warranty claims must be made immediately on detecting the defect Remember to quote the se rial number Consumable parts are not subject to the watranty All technical information data and instructions for operation contained in these operating instructions were up to date at time of print and are compiled on the basis of our experience and to the best of our knowledge We reserve the right to incorporate tech nical modifications within the scope of further de velopment of the product described in this manual No claims can be derived from the information il lustrations or descriptions contained in these in structions We assume no liability for any damage or malfunction caused by operating errors non com pliance with these operating instructions or inappro priate maintenance We expressly point out that only genuine Molift AS spare parts and accessories ap proved by us may be used For safety reasons the fitting and use of spare parts or accessories which have not been approved and unauthorised modifi cation or conversion of the product are not permit ted Molift AS will accept no liability for damages resulting from such acts With the exclusion of product liability Molift AS is liable for
26. t to the end of the bed Lower the user carefully Remove the loops from the suspension Removing the sling Gently pull the leg section to the side out from the user s thighs and towards yourself Pull the shoulder section under the neck of the user and roll her gently onto her side Pull the sling away and roll her onto her back Be careful when rolling the user onto her side Make sure you have control over the movement to prevent her from rolling com pletely over and out of the bed Lift and transfer to and from floor Lift and transfer from the floor is almost identical to a lift and transfer from bed please read this section There are two ways to lift from the floor Alternative lift 1 Place the users head on the chassis Use a pillow if appropriate to protect the head and neck of the user The suspension shall be centred over the user Lower the suspension enough to allow the sling loops to be hooked up Raise the user from the floor Position user in the sling by pulling the handle on the back of the sling Turn the user to face the lifting column and place the feet on the chassis Page 13 of 24 molift PARTNER Alternative lift 2 A floor based lift can also be performed by position ing the lifting column between the legs of the user as shown above Otherwise as alternative 1 Lowering to floor Place a pillow on the chassis or on the floor to pro tect the users head and neck not necessary
27. the content and contact your dealer for assistance if components are damaged e The box contains chassis lifting column lifting arm with suspension drive handle hand control battery and battery charger Assembly e The chassis should be rolled out of the box The battery must not be in the battery holder during assembly e Place the column in the attachment on the chas sis and the column will find the correct position If the column does not place itself correctly ro tate the drive with the unbraco key on the top and try again until the column has found the correct position e Make sure that the red arrow on the lower part of the column corresponds with the edge on the chassis Fix the column with the lock handle Arrow Lock handle molift designed for life molift PARTNER e Mount the lifting arm with suspension and rub ber protection on the trolley on the lifting col umn a e Slide the rubber protection up on the arm and guide the lifting arm on the trolley Push the arm down until the locking handle makes a clear click when the lifting arm 1s fixed correctly Be careful not to put fingers or similar under the lifting arm between arm and trolley Dan ger of personal injury e Slide the rubber protection back to cover the trol ley and pull it over the top and bottom edge e Connect the hand control cable to the contact on the battery holder The hand control has a hook that makes it pos
28. ts in order to locate the error See the table for troubleshooting Symptom Possible cause action The lifting col umn is wobbly The lifter only moves in one direction ad justable legs only moves in one direction The lifter moves uncon trolled ad justable legs moves uncon trolled Page 20 of 24 The lock handle is not locked properly or the lifting column is out of position in chassis veri fy position of lifting column and tighten the lock Hand control has failed test with another hand control and change if defective The control electronics has failed change control electron ics contact local representa tive for service Short circuit between hand con trol and lifter clean the contact to hand control with spirit to re move grease Hand control has failed change hand control contact local representative for service Defective control electronics change control electronics contact local representative for service The lifting arm does not move adjustable legs does not move Emergency stop activated but ton is pressed in turn button counter clockwise to reset Battery is empty change to a new battery or charge battery The motor connection is not in contact Reposition the lifting column use the allen wrench on top of column and check the arrow towards chassis see page 7 clean contact points on column and chassis The cable contact t
Download Pdf Manuals
Related Search