SMX 500
Contents
1. extr_15_3618_1 pkn IP Link Device Interface Revision 7 22 2009 Ethernet Communication Sheet This document provides additional assistance with wiring your Extron IP Link enabled product to your device Different components may require a different wiring scheme than those listed below For complete operating instructions refer to the user s manual for the specific Extron IP Link enabled product or the controlled device manufacturer supplied documentation Device Specifications Device Type Matrix Switcher Manufacturer Extron Firmware Version 1 08 Model s SMX 500 SMX 300 SMX 400 Minimum Software and Firmware Requirements rh Hnr pauls GC Version Compiler Firmware 1 4 1 15 3 0 Version History Driver Version Date Notes Initial Extron Certified version Tested on SMX400 firmware 1 7 14 2009 V 1 08 Driver Notes Page 1 of 4 extr_15_3618_1 pkn IP Link Device Interface Revision 7 22 2009 Ethernet Communication Sheet Control Commands amp States Audio Mute 1 16 On Off Global Audio Mute On Off Global Preset Recall Global Video Mute Output Output Control Plane Number Plane Preset Recall Audio Video Video Mute On Off Volume Output 1 16 0 to 64 in steps of 1 Discrete Status Available Audio Mute 1 16 On Off Connection Status Connected Disconnected Fan Status Normal Fan Problem Status Unavailable Status Displays Matrix Ties Temperature Status Norm2. 2 Select the desired input from the input command To configure a panel button output create the following button operations 1 Select the desired output from the output command 2 Select the desired take from the take command Configuring for audio control This section will describe how to configure the panel to control audio using the encoder knob Please note that there are a minimum of two selections required when configuring audio control To configure the panel encoder knob create the following button operations 1 Select the desired plane you wish to use 2 Select the desired audio control from either the Volume step or Volume discrete command Note Plane selected must support Audio Audio Mute Audio Gain Attenuation step and Audio Gain Attenuation discrete commands are dependent on the Output Control command which sets the audio output to be controlled and polled for status Thus only one audio output can be controlled and polled at a time Global Audio Mute is the only control that affects all audio outputs and is not dependent on the Output Control command Page 3 of 4 extr_15_3618_1 pkn IP Link Device Interface Revision 7 22 2009 Ethernet Communication Sheet Network communication When configuring the Ethernet driver be sure device settings match that of the GC configuration When configuring for a password Administrator login is required and the password must have a minim
3. al Temp Abnormally High Status Unavailable Video Mute On Off Voltage Level Normal Error Status Unavailable Volume Output 1 16 0 to 64 in steps of 1 Discrete Page 2 of 4 extr_15_3618_1 pkn IP Link Device Interface Revision 7 22 2009 Ethernet Communication Sheet Configuring input output s ties on a single button This section will describe how to configure a button with either a single input and output tie or single input to multiple output ties Please note that there are a minimum of four selections required when configuring a tie in this method To configure a button with a single input and a single output tie follow the steps below 1 Select the plane you want to use 2 Select the desired input from the input command 3 Select the desired output from the output command 4 Select the type of desired take from the take command To configure a button with multiple inputs and outputs repeat the steps above then follow the steps below 1 Insert a one second delay 2 Select the next desired output from the output command 3 Select the next desired take from the take command 4 Repeat as many times as desired Configuring for direct matrix front panel emulation This section will describe how to configure a panel to produce an input output selection capability To configure a panel button input create the following button operation 1 Select the desired plane you wish to use
4. um of 4 or maximum of 12 characters Port Type Ethernet Default User Name Default Password Default Port 23 Multi Connection Yes Capabilities Port Changeability Yes Logon Credentials Yes Supported Ethernet Driver Configuration Description Please refer to manual for setting and changes to Network Communication parameters such as User Name Password and Port Number Please look to Chapter 4 Software Configuration and Control for modification Changes to parameters can also be made through device default web pages in the Configuration Tab under System Settings Notes for the Device Page 4 of 4
Download Pdf Manuals
Related Search