the Sena SMH10 User Manual
Contents
1. com setting Jog Dial to enable Phone Button to disable Start end intercom conversation Tapping Reject incoming call Tapping Call transfer Tapping High tone short long beep Volume adjustment Rotating Track forward back Rotating w pressing FAN PAUS 1 sec Mid tone single beep Bluetooth music 9 SMH10 SENA BATTERY INFORMATION The SMH10 has an internal non removable rechargeable battery Do not attempt to remove the battery from the device as you may damage the device The battery can be charged and discharged hundreds of times but it will eventually wear out Recharge the battery only with SENA approved chargers designated for this device Use of an unapproved charger may present a risk of fire explosion leakage or other hazard Always try to keep the battery between 15 C and 25 C 59 F and 77 F Extreme temperatures reduce the capacity and lifetime of the battery A device with a hot or cold battery may not work temporarily Battery performance is particularly limited in temperatures well below freezing Do not dispose of batteries in a fire as they may explode Batteries may also explode if damaged Never use any charger that is damaged Operating times are estimates only and depend on the devices used together features used battery age and condition temperatures to which battery is exposed and many other factors MAINTENANCE AND CARE The SHM10 should be treated with care and the2. Consult the dealer or an experienced radio TV technician for help e FCC RF Exposure Statement The antenna s used for this device must be installed to provide a separation distance of at least 20 cm from all persons and must not be co located or operating in conjunction with any other antenna or transmitter e FCC Caution Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void user s authority to operate the equipment e CE Declaration of Conformity This product is CE marked according to the provisions of the R amp TTE Directive 99 5 EC Hereby SENA declares that this product is in compliance with the essential 19 SENA SmH10 requirements and other relevant provisions of Directive 1999 5 EC For further information please consult http www senabluetooth com Please note that this product uses radio frequency bands not harmonized within EU Within the EU this product is intended to be used in Austria Belgium Denmark Finland France Germany Greece Ireland Italy Luxembourg The Netherlands Portugal Spain Sweden United Kingdom and within EFTA in Iceland Norway and Switzerland e Bluetooth License The Bluetooth word mark and logos are owned by the Bluetooth SIG Inc and any use of such marks by SENA is under license Other trademarks and trade names are those of their respective owners The SMH10 is compliant with and adopts the Bluetooth Speci
3. SMH10 Bluetooth Stereo Headset and Intercom for Motorcycles 3 Bluetooth 2 J OO N A v2 1 va a 20 I C San g Intercom ad e ro 980yds Multi Pair Intercom Stereo Music A2DP AVRCP Versatile Jog Dial Audio Booster amp Bluetooth SENA www senabluetooth com Users Guide SENA smH10 CONTENTS INTRODUCTION Jeep cows ene eE EEEE EEEE EE EEE 3 PACKAGE CONTENTS je 4 INSTALLING THE SMH10 ON YOUR HELMET cceeceecc cece cece eet ee teen eeeeeeenees 5 POWERING ON OFF AND CHARGING rss dere kerseseidiaesiondes 7 e Powering On tserererererererereesesrererererererererererererererererererererese 7 e Powering Off seseseessssressereresrereseerereerereresrereseerereerereseerereerere 7 e Charging ttsteeseseeesesessererereseereresesrererereeeerereseseererereseererese 7 e Low Battery Warning tsteeeeeeeeeesererererereresesesrerererereresesesrererererere 8 PAIRING THE SMH10 WITH BLUETOOTH DEVICES rssssssrssreeresssssreererses 8 e Mobile Phone Pairing s rstrtrtr ects tree eet e tence teen eee e eee e teen nett eee eenees 8 e Bluetooth MP3 Player Pairing sssrccee eect e reese e nett ence eee eee ee eee e ene ee eeenees 9 e Bluetooth GPS navigation Pairing ssrrrttee reece tree eee e eee ee eee e eee eee eee e eee e anes 9 e Pairing with other SMH10 headsets for Intercom conversation s rrrrrrrrrrrsssseeeeeeeeeeee 9 ENG THE Free esse 11 e Volume Adjustment evrernnennnnnnnnnnnnennanennnnnnnnnnnnnnnnnnnnnennnnr
4. By Bluetooth Wireless Stereo The Bluetooth audio device must be paired with the SMH10 by following the Bluetooth Audio Device Pairing instructions described in the previous chapter The SMH10 supports the Audio Video Remote Control Profile AVRCP so if your SMH10 SENA Bluetooth audio device also supports the AVRCP you can use the SMH10 to remotely e To track forward or track back rotate while pressing the Jog Dial clockwise or control music playback So you may not only adjust the volume but also use the counter clockwise functions such as play pause next track and previous track e To adjust the volume rotate the Jog Dial e Function Priority The SMH10 operates in the following order of priority e To play or pause music press and hold the Jog Dial for 1 second until you hear MINES ONS none Intercom a beep Bluetooth stereo music and lowest stereo music by audio cable A lower priority function is always interrupted by a higher priority function For example stereo music is interrupted by intercom call and intercom conversation is interrupted by incoming mobile phone call 15 SENA SmH10 e RESET TO FACTORY DEFAULT SETTINGS 1 To restore the SMH10 to factory default settings press and hold the Phone Button for 12 seconds until the LED shows solid red and you hear double beeps 2 Then within 5 seconds press the Jog Dial to confirm reset The headset will be restored to factory setting and
5. following suggestions will help you protect your warranty coverage 1 Do not use or store the device in dusty dirty areas Its moving parts and electronic components can be damaged 2 Do not store the device in hot areas High temperatures can shorten the life of electronic devices damage batteries and wrap or melt certain plastics 3 Do not store the device in cold areas When the device returns to its normal temperature moisture can form inside the device and damage electronic circuit boards 4 Do not attempt to open the SMH10 5 Do not drop or knock the device Rough handling can break internal circuit boards and fine mechanics 6 Do not use harsh chemicals cleaning solvents or strong detergents to clean the device 17 SENA SmH10 7 Do not paint the device Paint can clog the moving parts and prevent proper operation DISPOSAL These suggestions apply equally to the headset main unit speaker microphone The crossed out wheel bin symbol on the product literature or camp Unitor powerenarger N 4 packaging reminds you that all electrical and electronic products EN batteries and accumulators must be taken to separate collection at the end of their working life This requirement applies to the systems are available To prevent possible harm to the environment or human European Union and other locations where separate collection health from uncontrolled waste disposal please do not dispose of these prod
6. for details Pairing with other SMH10 headsets for Intercom conversation 1 The SMH10 can be paired with up to three other headsets for Bluetooth Intercom conversation 2 Turn on the two headsets A and B that you would like to pair with each other 3 Press and hold the Jog Dial of the headset A for 5 seconds until red LED starts to flash rapidly 4 Press and hold the Jog Dial of the headset B for 5 seconds until red LED starts to flash rapidly 5 Simply tap the Jog Dial of any one of the two headset A or B It doesn t matter that you choose A or B and wait until the LEDs of both headsets turn to blue and intercom connection is automatically established Headset A Is paired with Headset B Pairng A amp B 6 You can make other pairings between the headset A and C and between the headset A and D by following the same procedure as above Headset A is paired with Headset C and with Headset D 09 SENA smH10 P aN 2 a K x ss ss H ss D D Pairing A amp C Pairing A amp D 7 Then you can also make other pairings between the headsets B C and D by following the same procedure as above Headset B is paired with Headset C and D and also Head C is paired with Headset D gt gt N p aber A I I I I I I I I v d U U HR a Pairing B amp C Pairing B amp D 10 N p i Ral x q Boe Pairing C amp D 8 Four he
7. is enabled Refer to the next section for detail 3 To reject a call tap the Jog Dial while the phone is ringing 11 SENA SmH10 4 To transfer a call between the mobile phone and the headset tap the Jog Dial during the phone conversation You will hear a short long beep when the call is transferred to the phone headset 5 There are several ways to make a phone call Enter number on your mobile phone keypad and tap the Phone Button The call is automatically transferred to the headset Tap the Phone Button in stand by mode to activate the voice dialing of your mobile phone For this the voice dialing feature must be available on the mobile phone Refer to your mobile phone manual for further instructions To redial the last number double tap the Phone Button in stand by mode Enabling Disabling Voice Activated Phone Answering Factory Default Disabled If this feature is enabled you can answer incoming calls by simply saying a word loudly enough For example when you hear a series of beeps by an incoming call you can answer the phone by saying Hello or any other word loudly The factory default setting is disabled You can enable or disable this mode If this mode is disabled the only way to answer an incoming call is to tap the Phone Button 12 1 Press and hold the Phone Button for 8 seconds until the red LED is rapidly flashing When you do this after first 5 seconds you press the button you will
8. see the headset enters into the Mobile Phone Pairing sequence but you have to keep pressing the button for another 3 seconds until the red LED flashes rapidly 2 To enable tap the Phone Button then the LED shows solid blue for 2 seconds and you will hear double beeps 3 To disable tap the Jog Dial then the LED shows solid red for 2 seconds and you will hear a single beep Intercom Conversation 1 You can start an intercom conversation with any of Intercom Friends by tapping the Jog Dial single tapping to intercom with the First Intercom Friend double tapping with the Second Intercom Friend and triple tapping with the Third Intercom Friend e et 279 Intercom Friend 1 Intercom Friend pet 3 Intercom Friend SMH10 SENA 2 To terminate an intercom conversation single tap the Jog Dial Any intercom connection with any Intercom Friend will be terminated by a single tapping A double or triple tapping will do nothing in this case Terminate Enabling Disabling Voice Activated Intercom Factory Default Disabled If this feature is enabled you can initiate an intercom conversation with the First Intercom Friend by speaking any word loudly enough For example you can start an intercom conversation with your First Intercom Friend by saying Hello loudly But this is only with the First Intercom Friend not with the Second or Third Intercom Friend f you and your In
9. switched off automatically 3 If you don t press the Jog Dial within 5 seconds the reset attempt is canceled and the headset returns to stand by mode e FAULT RESET When the SMH10 is not working properly or is in faulty status with any reason you may reset by pushing the pin hole reset button at the back of the headset main unit Insert a paper clip into the reset pin hole and press the reset button for a second with light pressure The SMH10 will be switched off and you have to turn on and try to use again However this will not restore the headset to factory default settings 16 OPERATION QUICK REFERENCE Button Description Duration LED Beep Phone Button Power on 1 sec Solid blue Ascending beeps Jog Dial Power off Tapping Solid red Descending beeps Phone Button Mobile phone pairing Blue amp red alternatively 5 sec High tone multiple beeps flashing MP3 GPS pairing 5 sec Fr SEE High tone multiple beeps 8 sec Red flashing Mid tone single beep Voice activated phone answering setting Phone Button to enable Jog Dial to disable Factory reset 12 sec Solid red High tone double beeps Jog Dial within 5 sec to confirm reset Make amp answer phone call Tapping Jog Dial Intercom pairing 5 sec Red flashing Double tone beeps Jog Dial of any one of the two headsets Voice activated Inter 8 sec Solid red Mid tone single beep
10. the Product b failure of Customer to adhere to any of SENAS specifications or instructions c neglect of abuse of or accident to the Product or d any associated or complementary equipment or software not furnished by SENA Limited warranty service may be obtained by delivering the Product to SENA or to the international distributor it was purchased through and providing proof of purchase or receipt date Customer agrees to insure the Product or assume the risk of loss or damage in transit to prepay shipping charges to SENA and to use the original shipping container or equivalent e Limitation of Liability EXCEPT AS EXPRESSLY PROVIDED HEREIN SENA MAKES NO WARRANTY OF ANY KIND EXPRESSED OR IMPLIED WITH RESPECT TO ANY EQUIPMENT PARTS OR SERVICES PROVIDED PURSUANT TO THIS AGREEMENT INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE NEITHER SENA NOR ITS DEALER SMH10 SENA SHALL BE LIABLE FOR ANY OTHER DAMAGES INCLUDING BUT NOT LIMITED TO DIRECT INDIRECT INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES WHETHER IN AN ACTION IN CONTRACT OR TORT INCLUDING NEGLIGENCE AND STRICT LIABILITY SUCH AS BUT NOT LIMITED TO LOSS OF ANTICIPATED PROFITS OR BENEFITS RESULTING FROM OR ARISING OUT OF OR IN CONNECTION WITH THE USE OF FURNISHING OF EQUIPMENT PARTS OR SERVICES HEREUNDER OR THE PERFORMANCE USE OR INABILITY TO USE THE SAME EVEN IF SENA OR ITS DEALER HAS BEEN ADVISED
11. unit on the helmet for any reason you may use the glued surface mounting adaptor to attach the Speaker Microphone unit on the external surface of the helmet e Remove the back plate of the Speaker Microphone clamp unit by loosening the two screws with the enclosed Hex Key e Attach the glued external adaptor to the Speaker Microphone clamp unit by tightening the two screws instead of the removed back plate e Locate a proper surface on the helmet to attach the unit clean the helmet surface location with a moistened towel and allow to dry thoroughly e Peel off the cover of the adhesive tape of the adaptor and attach the unit on the proper surface of your helmet i Attach Sena recommends the clamp unit over the glued surface mounting adaptor Even though the glued surface mounting adaptor is provided for convenience Sena does not assume any responsibility for use of it Users may have to use the glued adaptor at their own risk and responsibility 4 Attach the headset main unit to the Speaker Microphone clamp unit Insert the bottom part of the main unit completely into the lower slot of the clamp unit first Then push the upper part of the main unit until it clicks into the upper holder of the clamp unit 06 SMH10 SENA 5 To remove the main headset from the Speaker Microphone clamp unit hold the lower part of the Speaker Microphone clamp unit with your thumb and gently press down the hook on the upper part of t
12. 11 e Mobile Phone Call Making and Answering ttereseeeerrereerreseerreserereserereeeerees 11 e Enabling Disabling Voice Activated Phone Answering Factory Default Disabled 12 intercom Conversation Frere E da 12 Enabling Disabling Voice Activated Intercom Factory Default Disabled rrrrrrseeeeees 13 sea preke 14 ERE ES EE ET 14 See pre 14 e Function Priority rerereeeennnnnnnnnannnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 15 e RESET TO FACTORY DEFAULT SETTINGS ER ER 16 s FAULT RESET eane aea a E R a NS 16 OPERATION QUICK REFERENCE 08etesscies ran 16 BATTERY INFORMATION reke e paee 17 MAINTENANCE AND CARE Pre EnEn nnie 17 Ne EEE Ee A Eite EE EE 18 CERTIFICATION AND SAFETY APPARAT 19 e FCC Compliance Statement tttrrrrrrrrnennarnunnennnannuunennnnnnnuvenr 19 e FCC RF Exposure Statement crrrte esc c eect eee e eee e eee een e cece eee e neces ee eeeennees 19 Cele ti te er ee ee 19 e CE Declaration of Conformity sree eee e cette teen eee e ee eee eee eee n eee e cece eeeee ene n eens 19 FE ER 20 WAIVER AND GENERAL RELEASE 4 dren 20 e One Year Limited Warranty lt strtcee cette tee e teen eee e ee ee eee eee ee escent eee n ene e ness 22 e Limitation of Liability eeeeeesereseseserserereresesesrerereresesesrererereses 22 Hen re eS EEE ises ansis 23 WARNING Jr 23 SMH10 SENA INTRODUCTION Thank you for choosing the SENA SMH10 Bluetooth Stereo Headset and Intercom for motorcycles With t
13. ENA from any and all litigation claims debts demands actions and liability which may arise directly or indirectly from using the Device for any distress pain suffering discomfort loss injury death damages to or in respect to any person or property however caused WHETHER ARISING FROM THE NEGLIGENCE OR OTHERWISE and which may hereafter accrue to you on some future date as a result of said use to the fullest extent permitted by law 2 You fully understand and assume the risks in using the Device including risk of negligent acts or omissions by others 3 You confirm that you are physically capable to use the Device and that you have no medical conditions or needs that may infringe upon your abilities to do so ina safe manner You confirm that you are at least eighteen 18 years of age and that you have been advised of the risks associated with the use of the Device You further confirm that you will not consume any alcohol that may affect your alertness or any mind altering substance and will not carry use or consume these substances before or during the use of the Device 4 You fully acknowledge our warnings and understand that a risks and dangers exist in using the Device while in traffic including but not limited to injury or illness 21 SENA smH10 Strains fractures partial and or total paralysis death or other ailments that could cause serious disability b these risks and dangers may be caused by the negli
14. OF THE POSSIBILITY OF SUCH DAMAGES IN NO EVENT WILL SENA OR ITS DEALERS TOTAL LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT e Return for Full Refund IF YOU ARE UNWILLING TO ACCEPT AND AGREE TO THE ABOVE CONDITIONS YOU MAY RETURN THIS DEVICE TO SENA FOR A FULL REFUND PROVIDED THAT YOU DO SO NO LATER THAN 14 BUSINESS DAYS FOLLOWING THE PURCHASE OF THE DEVICE AND SUBJECT TO THE WRAPPING BEING INTACT WHEN DOING SO PLEASE REFER TO THIS SECTION BY NOT RETURNING THE DEVICE FOR REFUND WITHIN THE PERIOD PROVIDED YOU ARE EXPLICITLY IN AGREEMENT WITH THE ABOVE AND RENOUNCE ALL RIGHTS TO FUTURE CLAIMS AND DEMANDS AGAINST SENA AS DEFINED ABOVE WARNING SENA informs that using this device in public traffic may not be authorized by the law Please check your local law and use this device only out of public traffic such as private properties or closed circuits If the simultaneous use of both ear speakers while riding a motorcycle is prohibited by your local law please use only a single ear speaker while riding SENA denies any liability should you choose not to respect this warning 23 SENA www senabluetooth com v1 00 Users Guide
15. adsets are completely multi paired so that four persons can have Intercom conversations with each other 9 If a headset has multiple paired headsets for intercom conversations the lastly paired headset is set as First Intercom Friend The older Intercom friend goes to be Second Intercom Friend and Third Intercom Friend For example after the paring procedures as above the headset D is the First Intercom Friend of the headset A and the headset B is the Third Intercom Friend of the headset A SMH10 SENA 15 of A is D AE 3 of A is B 1 ofD is C 299 of D is B 37 of D is A 1 OG ED 2t of C js B IoC is A 1 ofB is D 20 of B is C 37 of B is A USING THE SMH10 Volume Adjustment You can easily adjust the volume by rotating the Jog Dial You will hear a beep when the volume reaches maximum or minimum level The volume is set and maintained separately at different levels for each function even when you turn off and on the headset For example once you set the mobile phone conversation volume it is not changed even if you raise the volume when you hear Bluetooth MP3 music So you can always maintain preferred optimum volume level for each function e Mobile Phone Call Making and Answering 1 When you have an incoming call simply tap the Phone Button to answer the call 2 You can also answer the incoming call by loudly speaking any word of your choice if the Voice Activated Phone Answering Function of the SMH10
16. fication 2 0 and has successfully passed all interoperability tests that are specified in the Bluetooth specification However interoperability between the device and other Bluetooth enabled products is not guaranteed 20 WAIVER AND GENERAL RELEASE By using the SMH10 you will waive substantial legal rights including the right to sue Please read the following carefully before using the device If you do not accept all terms of this agreement you should immediately return the product for a full refund By using the headset you agree to be bound to this agreement and forfeit the right to sue Using a communication device while riding a motorcycle scooter moped ATV quad bike or any other vehicle or equipment whether on land water or air jointly referred to as Vehicle requires your complete and undivided attention SENA Technologies Inc including its Officers Directors Affiliates Parent Company Representatives Agents Contractors Sponsors Employees Suppliers and Resellers jointly referred to as the Company or SENA strongly advises you to take all necessary precautions and remain alert to the traffic weather and road conditions if you choose to use the SMH10 headset including all derivative models irrespective of its commercial name or branding the Device and stop your Vehicle on the roadside prior to initiating or receiving calls Any publications advertisements announcements or similar notes tha
17. gence of the manufacturers or its agents or any third party involved in designing or manufacturing the Device c these risks and dangers may arise from foreseeable or unforeseeable causes You hereby assume all risks and dangers and all responsibility for any losses and or damages whether caused in whole or in part by the negligence or other conduct of others including the Company 5 You confirm that you have read this release of liability and fully understand its terms and that you have given up substantial rights by not returning the Device for a full refund see refund option below e One Year Limited Warranty Sena Technologies Inc SENA warrants that this product Product shall conform to and perform in accordance with published technical specifications and the accompanying written materials and shall be free of defects in materials and workmanship for a period of one 1 year from the date of purchase by the first consumer purchaser of the Product The limited warranty extends only to the original consumer purchaser of the Product and is not assignable or transferable to any subsequent purchaser end user 22 This warranty is limited to the repair and or replacement at SENAS discretion of defective or non conforming Product and SENA shall not be responsible for the failure of the Product to perform specified functions or any other non conformance caused by or attributable to a any misapplication or misuse of
18. he SMH10 you can call hands free on your Bluetooth mobile phone listen to stereo music or voice instructions of GPS navigations by Bluetooth wirelessly and have intercom conversations in full duplex with a passenger or other motorcycle riders The SMH10 is compliant with the Bluetooth Specification v2 1 supporting the following profiles Headset Profile Hands Free Profile HFP Advanced Audio Distribution Profile A2DP and Audio Video Remote Control Profile AVRCP Please check with the manufacturers of other devices to determine their compatibility with this headset Please read this user s guide carefully before using the headset Also check www senabluetooth com support for the latest version of the user s guide and additional information related to SENA Bluetooth products The SMH10 features e Bluetooth hands free for Bluetooth mobile phones e Bluetooth stereo headset for Bluetooth audio devices such as MP3 players e Bluetooth headset or stereo headset for Bluetooth GPS navigations e Bluetooth Intercom up to 900 meters 980 yards e Multi Pair Bluetooth Intercom for 4 persons e Stereo music by 3 5mm audio cable Key Specifications e Bluetooth v2 1 e Bluetooth Class 1 e Supporting profiles Headset Profile Hand Free Profile HFP Advanced Audio Distribution Profile A2DP Audio Video Remote Control Profile AVRCP in open terrain 03 SENA SmH10 PACKAGE CONTENTS Headset Main Unit DC P
19. he headset main unit with your index finger until it clicks out You may have to do this to charge up or to carry the headset main unit POWERING ON OFF AND CHARGING To power on and off the headset you don t need to press and hold any button for several seconds Just short press the Jog Dial and the Phone Button simultaneously and you will get quick on and off convenience e Powering On Press the Jog Dial and the Phone Button at the same time for about 1 second to power on The blue LED turns on and you will hear ascending beeps e Powering Off Just short press the Jog Dial and the Phone Button simultaneously you don t need to press and hold for a few seconds The red LED turns on for a while until it turns off completely and you will hear descending beeps e Charging The LED turns on red while charging and turns to blue when the headset is fully charged It takes about 2 5 hours to be completely charged 07 SENA smH10 Low Battery Warning When the battery is low the blinking blue LED in stand by mode turns to red and you will hear mid tone triple beeps in every one minute 08 PAIRING THE SMH10 WITH BLUETOOTH DEVIGES Before using the SMH10 Bluetooth headset with any of Bluetooth devices for the first time you need to do the pairing operation It can be paired with Bluetooth mobile phones Bluetooth audio devices such as MP3 or GPS and with other SMH10 Bluetooth headsets This pairing operation is on
20. ly required once for each Bluetooth device and the headset will remain paired with the devices and automatically connects to the paired devices again when they are within range e Mobile Phone Pairing 1 Turn on the headset and press the Phone Button for 5 seconds until the LED flashes red and blue alternately and you hear multiple beeps 2 search for Bluetooth devices on your mobile phone The headset will be listed on your mobile phone as SMH10 3 Enter 0000 for the PIN 4 The headset can be paired as Handsfree or Headset Handsfree profile is normally recommended for most mobile phones If it is paired as Headset the buttons of the SMH10 may not work properly SMH10 SENA e Bluetooth MP3 Player Pairing 1 The procedure is the same with the procedure of Mobile Phone Pairing except the SMH10 must be paired as Stereo Headset 2 If you use a Bluetooth mobile phone and a Bluetooth audio device at the same time please make sure to pair as Handsfree or as Headset with the mobile phone and to pair as Stereo Headset with the Bluetooth audio device e Bluetooth GPS navigation Pairing 1 You can listen to Bluetooth voice instructions from a Bluetooth GPS navigation 2 The paring procedure is the same with the procedure of Mobile Phone Pairing except the SMH10 could be paired as either Headset or Stereo Headset depending on the Bluetooth GPS navigation 3 Please refer to the manual of the Bluetooth GPS navigation
21. or any kind of Intercom related function and the Phone Button is for any functions of mobile phone With this reason as far as intercom function is concerned the Jog Dial is used for a positive manner of action such as enabling and the Phone Button is for a negative manner of action such as disabling Vice versa for the mobile phone functions Intercom Failure When you try to start an intercom conversation with an Intercom Friend who is already having an intercom conversation or a mobile phone call with another person you can t make it and will hear low tone double beep as a busy signal In this case you have to try again later Intercom Reconnection If your Intercom Friend goes out of range while having an intercom conversation you may hear static noise and eventually the intercom will be disconnected In this case the SMH10 automatically tries to reconnect the intercom every 8 seconds and you will hear high tone double beeps until the intercom is reestablished If you don t want to make a reconnection tap the Jog Dial to stop the attempt 14 e Stereo Music You can listen to stereo music in either way with the enclosed stereo audio cable or by Bluetooth wireless stereo 1 By Stereo Audio Cable Plug your stereo MP3 player directly to the SMH10 by using the enclosed 3 5mm stereo audio jack cable To adjust the volume rotate the Jog Dial on the headset You may adjust the volume on the MP3 player also 2
22. ower Charging port Phone Button Making and Answering a mobile phone call Entering into Mobile Phone Pairing Mode Entering into Bluetooth Audio Device Pairing Mode MP3 GPS navigation Entering into Voice Activated Phone Answering Setting Mode Jog Dial Start and End an Intercom Conversation Volume adjustment by rotating Play and Pause Bluetooth MP3 player Track forward and Track back by rotating while pressing the button Entering into Intercom Pairing Mode Entering into Voice Activated Intercom Setting Mode Reject an incoming mobile phone call e Call Transfer 04 e Speaker Microphone Clamp Unit Speakers Microphone lt MP3 Jack e DC Power Charger USB Power Cable CO Cigarette Charger 3 5mm Stereo Audio Jack Cable I e Glued Surface Mounting Adaptor SMH10 SENA e Microphone Sponges y Velcro Pads ta Hex Key Allen Wrench TC INSTALLING THE SMH10 ON YOUR HELMET 1 Insert the back plate of the Speaker Microphone clamp unit between the internal padding and external shell of the helmet Please make sure that the microphone is located properly close to your mouth when you wear the helmet 2 Please adjust the direction of the microphone so that the triangular mark on the microphone is pointing towards your mouth triangular mark 05 SENA SmH10 3 If you have any problem to clamp the Speaker Microphone
23. t refer to using the Device while riding a Vehicle are solely intended to address its technical SMH10 SENA capabilities and should not be misconstrued as if encouraging users to operate the Device while actively involved in traffic By way of purchasing this Device and not returning it for a full refund see below you are irrevocably releasing indemnifying from any liability loss claim and expense including attorneys fees and holding SENA harmless for any bodily injuries harm or death as well as losses or damages in goods to any Vehicles including your own or to any property or asset that belong to you or to third parties any of which may result from using the Device under any circumstances or conditions and irrespective of jurisdiction SENA will not be responsible for any physical damages irrespective of reasons conditions or circumstances including malfunctioning of the Device and all risks associated with operating it rest solely and entirely with the user of this Device irrespective of whether the Device is used by the original purchaser or any third party SENA hereby notifies you that using this Device may also be in contravention to local federal state or national laws or regulations and that any use of the Device is entirely at your sole risk and responsibility 1 You your heirs legal representatives Successors or assigns hereby voluntarily and forever release discharge indemnity and hold harmless S
24. tercom Friend remain silent for 20 seconds the intercom terminates automatically If this feature is disabled the only way to initiate and terminate an intercom conversation is to tap the Jog Dial 1 Press and hold the Jog Dial for 8 seconds until the red LED turns on solidly When you do this after first 5 seconds you press the Jog Dial you will see the headset enters into the Intercom Pairing sequence but you have to keep pressing the Jog Dial for another 3 seconds until the LED turns to solid red 2 To enable tap the Jog Dial then the blue LED flashes for 2 seconds and you will hear double beeps 3 To disable tap the Phone button then the red LED flashes for 2 seconds and you will hear a single beep However even when this feature is enabled if you terminated the previous intercom conversation by tapping the Jog Dial it will not automatically start again by voice activation In this case you have to tap the Jog Dial again to restart the intercom conversation The voice activation of the intercom occurs only when the previous intercom conversation was automatically terminated by 20 seconds of silence This is to prevent an unintentional start up of the intercom connection under strong windy noise environment In order to use the voice activation feature again in this case start intercom by pressing the Jog Dial and let it terminate automatically by 20 seconds of silence 13 SENA SmH10 Tip The Jog Dial is f
25. ucts as unsorted municipal waste but hand it in at an official collection point for recycling 18 SMH10 SENA CERTIFICATION AND SAFETY APPROVALS e FCC Compliance Statement This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions This device may not cause harmful interference and This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Download Pdf Manuals
Related Search