User Manual - Zeta Alarm Systems
Contents
1. D e D z Elte INSTRUCTION MANUAL 4 to 8 ZONE FIRE ALARM PANEL Other Connections The Premier Elite also has the following connections Fire Relay The Premier Elite has one volt free change over relay that operates on an alarm It is rated at 1Amp SELV The relay remains operated until the panel has been reset Fault Relay The Premier Elite has one volt free change over relay that operates on any fault condition The Relay is Normally energised so that it gives a signal in the event of total power failure Mains amp Battery back up It is rated at 1Amp SELV The relay remains operated until the fault has been cleared Class Change Input The class change input on a Premier Elite 4 8 zone F A C P will remotely operate the sounder circuits The Class change terminals should be connected to a normally open contact that closes when the sounders are required to sound Historically it was used to ring bells in school momentarily to signal end of lessons and lunch break It can also be used as a simple way of linking 2 control panels You would link from the fire relay on one panel to the class change on the other and vice versa Approved Document No GLT MAN 118 PAGE 7 Issue 1 Author NRPJ Date 15 11 2006 1 i P SLE 1222 INSTRUCTION MANUAL 4 to 8 ZONE FIRE ALARM PANEL Display amp Controls Here is the fascia for the Premier Elite Operating Instructions To Reset From Afte ch to th button 12. If a break is found splitting the line in half amp fitting EOL will help determine which section of cable has the fault As a panel check remove cable amp fit EOL at the panel If the fault clears the panel is working correctly If a panel does not report a fault when an detector is removed check with your supplier if the detector is compatible with the Premier Elite Short Circuit Fault Gen S C LED will be lit Check that the correct end of line has been fitted 1N4002 DIODE and check that it has not been fitted backwards It should be fitted stripe to ve Check that no equipment other than detectors or call points has been fitted to the zone Check for shorts to the cable screen Check that none of the heads have become damaged remove one at a time As a panel check remove cable amp fit EOL at the panel If the fault clears the panel is working correctly Sounder Circuit Fault A Sounder Fault is indicative of one or more of the following faults Sounder Open Circuit fault Check that the correct end of line resistor 10K has been fitted to both circuits Check that sounder fuses FS4 amp 5 are intact Check that there are no breaks in the cable and that all screw connections are secure As a panel check remove both circuits cable amp fit both EOLs at the panel If the fault clears the panel is working correctly Short Circuit Fault Gen S C LED will be lit Check that
3. Pr nder External Sounder Delay Over When the p lis FIRE ZONES E o B m0 POWER SUPPLY FLT FLT GENFIRE K pe ZONAL FAULT DISABLEMENT TEST nn EEE nan an Bn B wm GENFLT SYSTEM FLT GEN S C STOP START SILENCE RESET SCROLL GEN ZONE TEST GENERAL 4 ben FAULT SHORT CIRCUIT FAULT K FAULT TONE LED TEST DISABLE OVERRIDE EXTERNAL SOUNDER DELAY Premler E amp x FIRE ALARM CONTROL PANEL ED 4 ce m ALARM SYSTEMS vA It should be noted that the Yellow zonal indication LEDs are used to indicate several conditions They are used for Zone fault GEN FLT will also be lit Zone Disablement GEN DISABLEMENT will also be lit Zone Test GEN TEST will also be lit Approved Document No GLT MAN 118 PAGE 8 Issue 1 Author NRPJ Date 15 11 2006 D e D F z Elte INSTRUCTION MANUAL 4 to 8 ZONE FIRE ALARM PANEL Display The Premier Elite has the following LED indicators LEDs LIT LED CONDITION PANEL STATUS POWER CONSTANT GREEN The panel is supplied with power and has no faults fires System Normal GEN FLT CONSTANT YELLOW Problem with keyswitch connections ONLY GEN FLT amp CONSTANT YELLOW There is a problem with either the mains supply or the battery backup SUPPLY FLT FLASHING YELLOW GEN FLT amp CONSTANT YELLOW There is a wiring problem One of the cables is touching the earth screen EARTH FLT FLASHING YELLOW GEN FLT amp
4. Test the Alarm sounders operate for approximately seven seconds on and seven seconds off This cycle continues until the cause of the Alarm is removed either by the test smoke clearing from the detector or the manual call point being reset at which point the detector circuit also automatically resets Should an Alarm occur on a zone that is not programmed to test the Alarm will be processed in the normal way The testing of the zone in test will temporarily be suspended until the Alarm s from the other zones are reset At this point zone retesting may resume To Programme Zone In Test NOTE Only one zone can be programmed in test at any one time 1 Insert and turn control key to enabled position 2 Press engineer switch until the General Zone test LED is on flashing fast 3 Enter Engineer Code 4114 and then the General Zone Test LED is on flashing slow 4 Press scroll switch and Zone one fault LED will flash in synchronisation with the General Zone test 5 Press scroll button to the desired Zone for test Once the desired Zone LED is flashing this Zone is now in test mode 6 Once testing of that zone is completed press scroll button to move to another Zone or turn the control key switch to off position to exit test mode Approved Document No GLT MAN 118 Issue 1 Author NRPJ Date 15 11 2006 PAGE 16 0 010 OJO JE D EEE EE 3 i EEE o Zonal gt Output PP Card m Cl nn gt D e P
5. lit Continue to press scroll until the desired Zone or sounder is lit Press the Engineer button The GENERAL DISABLEMENT LED will be lit constantly indicating that this zone or sounder is now disabled If more than one zone needs to be disabled then press scroll again until the required zone is selected If the panel needs to be taken out of SELECT DISABLEMENT MODE eg to silence a fault on another part of the system turn the keyswitch off then back on again Once all the work has been done the zones need to be enabled again If the panel is still in SELECT DISABLEMENT MODE jump to paragraph 8 otherwise turn the keyswitch to controls enabled press engineer button GENERAL DISABLEMENT LED will flash fast Press scroll and it will return to being on steady The panel is now in SELECT DISABLEMENT MODE Press the scroll button until the disabled zone has been selected Press engineer button Scroll to any other disabled zone and enable in the same way When all zones are enabled again the GENERAL DISABLEMENT LED will flash slowly Turn the keyswitch to off to return the system to normal Approved Document No GLT MAN 118 PAGE 15 Issue 1 Author NRPJ Date 15 11 2006 Oro B e p Elite INSTRUCTION MANUAL 4 to 8 ZONE FIRE ALARM PANEL Test Mode To aid commissioning and assist routine maintenance check a non latching one man test facility is available When a detector or manual call point is triggered on any zone in
6. than 21V TOTAL CHARGER OUTPUT 1 1 Amp Enclosure Specifications DESCRIPTION VALUE ENCLOSURE SIZE 355 x 275 x 100 mm TOP CABLE ENTRIES 12 x 19mm DIA GROMMETED ENTRIES BOTTOM CABLE ENTRIES 2 x 19mm KNOCKOUT ENTRIES REAR CABLE ENTRIES 2 SNAP OUTS 60 x 20mm Fuse Ratings FUSE NO DESCRIPTION RATING FSI Charger Fuse 1 6A time delay 5 x 20mm glass FS2 Battery Fuse 1 6A time delay 5 x 20mm glass FS3 EN54 SUPPLY NOT USED 1 6A time delay 5 x 20mm glass FS4 Sounder circuit 1 400mA time delay 5 x 20mm glass FS5 Sounder circuit 2 400mA time delay 5 x 20mm glass INLET FUSE Mains Protection Fuse 2A Quick Blow HBC 5 x 20mm ceramic Approved Document No GLT MAN 118 Author NRPJ Date 15 11 2006 Issue 1 PAGE 19 Premie CCZ INSTRUCTION MANUAL 4 to 8 ZONE FIRE ALARM PANEL Log Book MAINTENANCE WORK DATE TIME ZONE LOCATION REASONFOR WORK WORK CARRIED OUT ADDITIONAL WORK REQUIRED SIGNED Approved Document No GLT MAN 118 Issue Author NRPJ Date 15 11 2006 PAGE 20 p 4 Ar CCZ INSTRUCTION MANUAL 4 to 8 ZONE FIRE ALARM PANEL
7. 06 p E g Elite INSTRUCTION MANUAL 4 to 8 ZONE FIRE ALARM PANEL Introduction The Premier Elite 4 to 8 zone panels have been designed to meet the requirement of an easy to use fully functional fire alarm control panel It is available as either a 4 zone panel 6 zone panel or an 8 zone panel Each version has 2 sounder circuits an alarm relay and a fault relay The sounder circuits can have a programmable delay set There is an option to add a zonal output board which can be used to drive zonal relays or a hard wired repeater panel There is no configuration simply connect the detectors amp sounders and apply power The Premier Elite range also includes a low cost 1 amp 2 zone version These panels are NOT covered in this manual They have a separate manual Approved Document No GLT MAN 119 P Issue 1 Author NRPJ Date 22 11 2006 e P z Elte INSTRUCTION MANUAL 4 to 8 ZONE FIRE ALARM PANEL Mains amp Battery Connecting the mains The Mains supply to the FACP is fixed wiring using Fire resisting 3 core cable Between 1 mm and 2 5mm or a suitable 3 conductor system fed from an isolating double pole switch fused spur fused at 3A IT SHOULD NOT BE CONNECTED THROUGH AN RCD This should be secure from unauthorised operation and be marked FIRE ALARM DO NOT SWITCH OFF The supply must be exclusive to the Fire Panel MAKE SURE ANY SPARE ENTRY HOLES ARE COVERED WITH THE GROMMETS PROVIDED Connecting th
8. CONSTANTYELLOW There is an open circuit fault in the wiring of the zone indicated ZONAL FLT FLASHING YELLOW GEN FLT amp CONSTANT YELLOW There is a short circuit fault in the wiring of the zone indicated ZONAL FLT FLASHING YELLOW GEN S C FLASHING YELLOW GEN FLT amp CONSTANT YELLOW There is an open circuit fault in the wiring of one or both of the sounder SND FLT FLASHING YELLOW circuits GEN FLT amp CONSTANT YELLOW There is a short circuit fault in the wiring of one or both of the sounder SND FLT FLASHING YELLOW circuits GEN S C FLASHING YELLOW GEN FLT amp CONSTANT YELLOW A processor fault has occurred To reset turn keyswitch on then back off If SYSTEM FLT CONSTANT YELLOW problem persists consult your dealer GEN FIRE CONSTANT RED A manual evacuation has occurred ONLY The sounders will be active GEN FIRE amp CONSTANT RED A fire has occurred in the zone indicated ZONE FIRE CONSTANT RED The sounders will be active GEN FIRE amp CONSTANT RED A fire has occurred in the zone indicated ZONE FIRE amp CONSTANTRED The sounders have a delay set and will become active after the GEN DISABLE CONSTANT YELLOW programmed delay To override the display press delay override amp DEL CONSTANT YELLOW GEN DISABLE FLASHING YELLOW The panel is ready for selecting disable or test mode FAST 4 HZ GEN DISABLE FLASHING YELLOW The panel is in SELECT DISABLEMENT MODE SLOW 05HZ GEN DISABLE FLASHING YELLOW The user is scrolli
9. FALSE ALARMS DATE TIME ZONE CAUSE IF KNOWN MAINTENANCE MAINTENANCE CATEGORY OF FURTHER SIGNED LOCATION OR ACTMTIES IN VISIT NEEDED FINDINGS FALSE ALARM ACTION ALARMAREA YES NO REQUIRED Approved Document No GLT MAN 118 PAGE 21 Issue 1 Author NRPJ Date 15 11 2006 p ALL OTHER EVENTS Elie INSTRUCTION MANUAL 4 to 8 ZONE FIRE ALARM PANEL DATE TIME ZONE LOCATION DETAILS OF EVENT ACTION DATE INTIALS INCLUDING CAUSE IF KNOWN REQUIRED COMPLETED Approved Document No GLT MAN 118 PAGE 22 Issue 1 Author NRPJ Date 15 11 2006
10. GLT MAN 118 Author NRPJ Date 15 11 2006 Issue 1 PAGE 10 p z Elte INSTRUCTION MANUAL 4 to 8 ZONE FIRE ALARM PANEL Alarm Condition amp Resetting an alarm The Premier Elite signals an alarm by the following Turn on the General Fire LED Turn on the Zonal Fire Indicator Turn on internal buzzer Start any sounders connected to the panel s sounder circuits Activate the fire relay What to do in the event of a fire Follow the building evacuation procedure and check that everyone has left the building safely The building fire officer or responsible person should CAREFULLY enter the building and locate the area of the alarm from the fire alarm panel Investigate to determine the cause of the alarm Look for the detector in the zone in alarm that signalled the fire The detector that signalled an alarm will have its RED ALARM LED on If a small fire is found a suitably trained person could tackle this with a suitable fire extinguisher If a larger fire is found leave the building immediately and contact the fire brigade If no fire is found make a note of the detector that signalled fire and look for anything nearby that could be the cause of the activation eg cooking or use of a hot air gun etc Record findings in the fire alarm log book Resetting from an alarm condition After the relevant action has been taken the Premier Elite fire alarm panel can be reset by the following 1 2 3 Press S
11. Premier Elze FIRE ALARM CONTROL PANEL Instruction Manual 4 8 zone F A C P D e P z Elite INSTRUCTION MANUAL 4 to 8 ZONE FIRE ALARM PANEL INDEX INDEX qu a Taaa 2 ocerstirento C 3 Mains 8 Battery A 4 Connecting the MAINS istisne aa e E aE ESEE E EENE R EAE EEEN EEIN Ena 4 Connecting the batteries creen rr ER CIERRE E ERE STEET EEEE 4 Charger Short Circuit Protection eese eene eene nennen nenne enne enne 4 D tectors amp soundets eet tit in Rep ER REN Een ere aere eret oee 5 WATS THE CELE CLOTS eee er DR UR er REN Hx Genten eet etse Yee PESE RYE Ee nnee 5 Diode Bases c 5 Zone Short Circuit Protection nononono nennen sernseenneenneernseenneennveenveenneenneeenneenneenn 5 Wiring the soundets er d eren ERR ee step lb eee 5 Setting a Sounder Activation Delay eese enne 6 enge DIE 7 Bire Jp 7 Fault Relay M nes ee en 7 Class Change Input soo rettet aetema nette Dee t t tete eus a Display amp Controls 5 ero rere eisen 8 Display er c 9 Controls raes 10 Alarm Condition amp Resetting an alarm eese nennen eterne nnns 11 What to do in the event of a Tire iiianoe iiaeiai e
12. atteries are disconnected Approved Document No GLT MAN 119 PAGE Issue 1 Author NRPJ Date 22 11 2006 D e P E Elite INSTRUCTION MANUAL 4 to 8 ZONE FIRE ALARM PANEL Detectors amp sounders Wiring the detectors The Premier Elite has been designed to use a 1N4002 diode end of line on the detector zones Zone ER 7 1N4002 End of G l line diode mm A Stripe to ve gt Ie c Zone When common bases are used call points should be connected to the start of the zone so that removing a detector head will not remove power from the call points Diode Bases The Premier Elite 4 8 zone can also be used with diode bases Diode bases allow call points amp detectors to be mixed on the same zone without any restrictions The diode also known as a continuity diode passes power to the downline detectors and call points if a detector head is removed for any reason Zone Short Circuit Protection The Premier Elite 4 8 zone panel has a higher zone output current than the 1 2 zone panels This is to allow them to drive larger zones and zone powered beam detectors etc In order to protect the panel in the event of an overload the panel will turn off the zone voltage if the current in that zone exceeds 70mA The panel will then try to restart the zone during the next Open circuit monitoring cycle These occur once every 60 seconds Wiring the sounders The Premier Eli
13. button They will clear automatically when the fault has been fixed The exception is a SYSTEM FAULT which means that the processor may have crashed and may or may not have restarted correctly Fault Finding Supply fault A power supply fault is indicative of one or more of the following faults Loss of Mains power Check that 230V AC is present at the mains terminal block Check mains fuse Check that there is 30 34V coming from the transformer secondary Check charger fuse FS1 Loss of Battery power Check that 2 X 12V batteries are fitted in series to give 24V backup Check battery fuse FS2 Check that battery connections are secure Check that the batteries are not over 5 years old Check that the 2 batteries have a combined voltage of over 21V DC Approved Document No GLT MAN 118 PAGE 12 Issue 1 Author NRPJ Date 15 11 2006 D e D z Elte INSTRUCTION MANUAL 4 to 8 ZONE FIRE ALARM PANEL Zone Fault A Zone Fault is indicative of one or more of the following faults Open Circuit fault e Check that the correct end of line DIODE 1N4002 has been fitted e Check that there are no breaks in the cable and that all screw connections are secure e Check that no detectors have been removed from the circuit Check that all detectors are correctly fitted to their bases As a cable check remove zone wire from panel Temporarily join the amp cables at the end of line amp Check for continuity
14. e batteries The Premier Elite requires 2 x 12 V sealed lead acid SLA batteries The two batteries are wired in series The ve of one battery is connected to the red battery lead The ve of the other battery is connected to the black battery lead The ve of the first battery is connected to the ve of the second battery using the link wire supplied Although there are many sizes of suitable battery the sizes we usually recommend are 12V 2Ah for standard backup or 12V 7Ah for extended backup 72 hour or more and the enclosure has been designed to hold these two battery sizes CO a Cole Ca a cal o d 8 9 garrERY o INIERCONNECTING _ TOPCB 5 TOPCB CABLE BATTERY INTERCONNECTING 9 case p SEALED LEAD ACID BATTERY SEALED LEAD ACID BATTERY UV 7 Ah 12V 2 Ah SEALED LEAD ACID BATTERY 12V 7Ah O O 2 x 2Ah Batteries Charger Short Circuit Protection The Premier Elite has an intelligent charger that senses if too much current is being drawn for instance in the case of totally discharged batteries or the charger leads being shorted together In such an event the Premier Elite 4 8 zone panel will turn off the power to its charger circuit The panel also turns off the charger when the b
15. general 1 25 X 0 5 x 0 757 24 x 0 0536 guideline would be 1 25 X 0 3785 1 2864 1 25 x 1 6649 2 08 Ah now wou 1 2 or 4 zone use 2 x 12V 2 2Ah 6 or 8 zone use 2x 12V 7 0Ah So 2 2 Ah batteries will be suitable for this installation Approved Document No GLT MAN 118 Issue 1 Author NRPJ Date 15 11 2006 PAGE 18 ae e p Elite INSTRUCTION MANUAL 4 to 8 ZONE FIRE ALARM PANEL Specifications Electrical Specifications ELECTRICAL DESCRIPTION VALUE MAINS VOLTAGE BATTERY VOLTAGE 230V AC 10 50 60 Hz 24V DC 2 X 12V SLA BATTERY SYSTEM VOLTAGE 24V DC NOMINAL 18 32 V SYSTEM VOLTAGE RIPPLE 2V PK PK MAX CHARGER SIZE UP TO 7AH in 24 Hours ZONE VOLTAGE 21V DC NOMINAL 20 22 5V SOUNDER ALARM OUTPUTS 2 x 400mA 24V DC Nominal AUXILIARY FAULT OUTPUT 1 x RELAY SELV 1A MAX AUXILIARY FIRE OUTPUT 1 x RELAY SELV 1A MAX NUMBER OF ZONES 1 2 4 6 8 MAXIMUM ZONE CAPACITY 32 DEVICES PER ZONE MAXIMUM ZONE RESISTANCE 70 ohms REMOTE SOUNDER ACTIVATION VIA N O CONTACTS SOUNDER ACTIVATION DELAY 0 9 MINUTES IN 1 MIN INCREMENTS ZONE END OF LINE DEVICE 1N4002 DIODE CATHODE STRIPE TO SOUNDER END OF LINE DEVICE 10 K RESISTOR CHARGER VOLTAGE 28 4V 25 C NO BATTERY CONNECTED ZONE SHORT CIRCUIT PROTECTION 100mA CHARGER SHORT CIRCUIT PROTECTION Batteries less
16. iaa E ar ernennen 11 Resetting from an alarm condition eese nennen nennen tenete 11 Fault display amp fault finding nnn eenneeneeeneneeneerneeeneeenseeeneneneeenneeeneeenevensvenvereneeens 12 Fault EInding eors ie a a E meer 12 Supply tauli une ee e E e Eaa EEEE Eea 12 vds 13 Sounder Circuit Eault 5e eere ete teer rote etta ihe ere ra ea eto e nn ER PECES ua ERR pieno aea ee 13 Earth Fault reet ree ERR peer quiere een 14 System Pault eer ERR NEU Mas gens sa PU lerne ATH Ie eere EE 14 Disablement ME 15 TO PROGRAMME ZONE OR SOUNDERS AS DISABLED ener 15 Test Mod haha ses release 16 TO PROGRAMME ZONE IN TEST neme eenseenneenneerneeeneeenseernerenenn 16 Optional Repeater Driver eene RR anini eaa RUNE reiben eh 17 Battery SN OE on 18 sample Calculation 2 5 5 2 2 o rettet ea REPRE RR E RER EAE dads NEEE acces va EEEa 18 SPECIHHCAUONS are ee ee ee era metteneetiaceeey 19 Electrical Specifications iiit een anna 19 Enclosure Specifications zuerst rao oto erepti pest Pe essa dent arend eene e kN E ep sus erahnen 19 Fuse Ratin Serince EET 19 Los BOOK utet e E E E E PE 20 MAINTENANCE WORK rrr tr ira eea e SN vac EH E EE EEEa eiaa 20 FALSEALARMS eepe onair aose e e ri E ens edureqedaunrni sac E R EEEE E 21 ALL OTHER EVENTS sans ale ablesen 22 Approved Document No GLT MAN 119 P Issue 1 Author NRPJ Date 22 11 20
17. ng through zones to select which one to disable or user ZONE DISABLE SLOW 05HZ has just enabled the zone GEN DISABLE CONSTANT YELLOW The indicated zone is disabled ZONEDISABLE CONSTANT YELLOW GEN DISABLE CONSTANT YELLOW The Sounders are delayed by the amount set on the rotary switch DEL CONSTANT YELLOW GEN TEST FLASHING YELLOW The indicated zone is in Test Mode ZONEDISABLE FLASHING YELLOW VERY SLOW 025HZ Approved Document No GLT MAN 118 Issue 1 Author NRPJ Date 15 11 2006 PAGE 9 D e D z Elte INSTRUCTION MANUAL 4 to 8 ZONE FIRE ALARM PANEL Controls The Premier Elite has the following controls BUTTON LABEL USE 1 START STOP Used to silence the sounders in an alarm or to manually start the sounders to evacuate building 2 SILENCE FAULT TONE Used to silence the panel s internal buzzer in a fault or alarm condition 3 RESET Used to return the panel to its normal condition after an ALARM condition Reset will not clear faults 4 LED TEST To check that all indicator LEDs are working Use as part of the daily weekly fire alarm inspection Engineer ENGINEER Used to access Disablement mode or Test Mode Delay DELAY OVERRIDE Used to start sounders immediately in the event of Override the panel having a delay to the sounders Note that the controls can only be used after the keyswitch has been turned to the ON position Approved Document No
18. rrect itself Should this fault occur the System Fault LED General Fault LED General Fault relay and fault internal buzzer will be constantly active until the control keyswitch is turned from off position to control enable position This should cause this fault condition to reset If not consult your supplier Approved Document No GLT MAN 118 Issue Author NRPJ Date 15 11 2006 PAGE 14 D e D F z Elte INSTRUCTION MANUAL 4 to 8 ZONE FIRE ALARM PANEL Disablement The Premier Elite 4 8 zone allows any zone or the sounder circuit to be disabled to aid commissioning and assist routine maintenance work When a zone or sounder cct is disabled the panel will not respond to any fault or fire signals it receives from that zone This might be used if the system requires routine maintenance and the customer needs the system to continue running but doesn t want spurious false alarms The panel will respond in the usual manner to any events in any non disabled zones To Programme Zone Or Sounders As Disabled Any number of zones or the sounders can be disabled but it is good practice to only disable one zone at a time Insert and turn control key to enabled position Press Engineer switch and the GENERAL DISABLEMENT LED will come on flashing fast Press Scroll switch and the GENERAL DISABLEMENT LED will flash slowly The panel is now in SELECT DISABLEMENT MODE Press scroll button again Zone 1 DISABLEMENT LED will be
19. te has 2 sounder circuits each rated at 400mA Each sounder circuit must be fitted with a 10k end of line resistor SND 4 SND SOUNDER SOUNDER SOUNDER SOUNDER 10K Eu End of tt Line Resistor Approved Document No GLT MAN 119 PAGE Issue 1 Author NRPJ Date 22 11 2006 Dos er Elite INSTRUCTION MANUAL 4 to 8 ZONE FIRE ALARM PANEL Setting a Sounder Activation Delay On the Premier Elite there is the option to delay the sounder activation in the event of a fire This might be useful in schools or clubs where the responsible person might want to verify the alarm before having a mass evacuation of the building A false alarm can be reset before the sounders operate If it is a true alarm the sounders can be started before the timer finishes by pressing the DELAY OVERRIDE BUTTON To set a delay open the panel door using Alan Key provided and set switch 7 SW7 using a terminal screw driver to the delay required SW7 Setting External sounder delay in minutes Q 0 No delay 1 1 minute Qo wo 2 2 minutes 3 3 minutes 4 4 minutes ym 5 5 minutes Co 6 6 minutes Oo 7 7 minutes X 8 8 minutes 9 9 minutes When a delay is set the panel will show GENERAL DISABLEMENT and DEL sounder DELay Approved Document No GLT MAN 119 P Issue 1 Author NRPJ Date 22 11 2006
20. the correct end of line has been fitted to both circuits 10k resistor e Check that ALL sounders Bells etc are POLARISED and are fitted the correct way round see diagram after list Check for shorts to the cable screen As a panel check remove cable amp fit EOL at the panel If the fault clears the panel is working correctly Note If non polarised CONNECTOR J alarm devices eg some types of old mechanical bell or a relay are Ms used then a diode will line Resistor have to be placed in line with the device to enable fault monitoring They may also need a back EMF protection diode symptoms Chattering sounder relays that don t turn off Approved Document No GLT MAN 118 PAGE 13 Issue 1 Author NRPJ Date 15 11 2006 D e D F z Elte INSTRUCTION MANUAL 4 to 8 ZONE FIRE ALARM PANEL Earth Fault An EARTH fault indicates that something is shorting to earth usually through the cable screen Disconnect the earth screens one at a time to determine the problem line Note connecting other equipment eg an oscilloscope or PC to the panel can give an earth fault The voltage between battery Ve and earth should be 14 16 volts If it is not the voltage should indicate what is shorting to earth System Fault A system fault is an abnormal microprocessor running condition due to various unexpected phenomena This will result in the panel attempting to co
21. top Start sounder button BUTTON 1 This will silence the external sounders Press Silence Fault Tone button BUTTON 2 This will silence the panel s internal buzzer Press the Reset button BUTTON 3 This will return the panel to it s normal condition If the panel goes straight back into alarm then the cause of the alarm has not been cleared This could be a detector still exposed to smoke or a call point still in the active position Press Buttons 1 amp 2 on the panel then investigate for a call point or detector that still has it s RED ALARM LED on Reset the call point or clear the smoke If the problem persists contact an engineer Approved Document No GLT MAN 118 PAGE 11 Issue 1 Author NRPJ Date 15 11 2006 Oro B e p Elite INSTRUCTION MANUAL 4 to 8 ZONE FIRE ALARM PANEL Fault display amp fault finding The Premier Elite 4 to 8 zone panels monitor for the following faults Low or failed mains Including fuses Low or failed battery Including fuse Detection Zone open circuit wiring fault Detection Zone short circuit wiring fault Detection Zone detector removed Sounder circuit open circuit wiring fault Sounder circuit short circuit wiring fault Earth Fault System fault Most of these faults will need to be checked by an engineer but the system can be checked for a removed detector by the responsible person All faults in the Premier Elite are NON LATCHING IE they can not be reset with the reset
22. x MCP 8 x Optical Zone 2 1 x MCP 7 x Optical Zone 3 3 x MCP 9 x Optical 2 x heat detector 1 x heat detector 1 x heat detector Zone 4 1 x MCP 10 x Optical 0 x heat detector Sounder CCT 1 10 x Maxitone sounder Sounder CCT 2 12 x Maxitone sounder ITEM QUIESCENT ALARM PREMIER ELITE 2 66mA 99mA MCP OmA 40mA OPTICAL 100uA 40mA HEAT 50uA 40mA MAXITONE SOUNDER OmA 25mA To calculate the required battery backup required we use the equation Battery Size Standby time in Amp Hours 1 25 x TaLm x lam Tspy x Isay Jl Where Tatm Maximum time in hours required for the alarm Ve hour is most common time la m Total Alarm Current in amps for all alarm devices connected to the alarm circuits Tsgy Standby time in hours for the system after mains failure normally 24 48 or 72 hr Issy Quiescent current in amps of control panel in fault condition because of mains failure PLUS all detection zones la m PREMIER ELITE ALM 22 X MAXITONE ALARM 1 X DETECTOR ALM 7 X MCP QU 33 X OPT QU 4x HT QU 20 163 22x 0 025 1x 0 040 7x0 33x0 0001 4x0 00005 0 163 0 55 0 04 0 0 0033 0 0002 0 757 Amps lsgy PREMIER ELITE QU 22 X MAXITONE QU 7 X MCP QU 34 X OPT QU 4 x HT QU 0 050 22x0 7x0 34x0 0001 4x0 00005 0 050 0 0 0 0034 0 0002 0 0536 Therefore Battery size It is always best to calculate battery requirements but our
23. z Ekte INSTRUCTION MANUAL 4 to 8 ZONE FIRE ALARM PANEL Optional Repeater Driver The Premier Elite has a connection to fit an optional Zonal Output Card The card fits next to the display PCB on the fire alarm panel door e Zonal Card SC rew Connection PCB Support je This can either be used in two ways 1 As a stand alone board that has zonal 29 Volt outputs suitable for connecting relays etc 2 It can be used to drive a hard wired repeater panel The panel would need the following connections to the repeater V Supply Voltage OV Supply ground GA General Alarm signal CF Common Fault Signal TN Buzzer Active Signal tone It will also need 1 connection per zone Approved Document No GLT MAN 118 PAGE 17 Issue 1 Author NRPJ Date 15 11 2006 D e D z Elte INSTRUCTION MANUAL 4 to 8 ZONE FIRE ALARM PANEL Battery Calculation Here are the current consumption of the Premier Elite panels in various conditions Control Panel Model Mains Fail buzzer sounding Mains Fail buzzer silenced Mains fail panel in alarm Premier Elite 4 8 Zone 50mA 31mA 163mA Sample Calculation A Premier Elite 4 zone panel has the following items connected Zone 1 2
Download Pdf Manuals
Related Search