CR-2210 SERIES CASH DRAWER USER`S MANUAL
Contents
1. controller responds to RS232 signals When switch position 1 is OFF the cash drawer works to USB interface USB PID select Switch positions 2 3 or 4 define a drawer number for the cash drawer as in below table so that this cash drawer is going to respond accordingly in USB communication Please note that within each system there should never be any 2 USB interface cash drawers carrying the same drawer number Part 5 USB PID JPI SW 1 2 3 4 5 6 7 0 2 ON ON ON OFF OFF OFF OFF ON 3 ON OFF OFF ON ON OFF OFF ON 4 OFF ON OFF ON OFF ON OFF ON Default setting Drawer 7 SW2 OFF SW3 OFF SW4 OFF UPOS and WEPOS driver application Please first find in Posiflex Product Information CDROM or download from Posiflex web sites for UPOS driver setup In this application CR 2214 responds to OpenDrawer command only CR 2210 2214 are compliant to UPOS version 1 7 and CR 2215 is compliant to UPOS version 1 8 and is also WEPOS certified Part 6 SPECIFICATIONS CR 2210 1 Follow the printer s manual of the printer the cash drawer is connected to open cash drawer 2 If the cash drawer is connected to a Posiflex POS system follow the technical instruction of the system to open the cash drawer CR 2214 1 Under DOS prompt type MODE COMI 9600 N 8 1 Hit the ENTER key 2 Type TYPE CON gt COM1 Hit the ENTER key 3 Type CTRL G Press Ctrl and G keys2. furnishing performance or use of this material This information is provided as is and Posiflex Technology Inc expressly disclaims any warranties expressed implied or statutory including without limitation implied warranties of merchantability or fitness for particular purpose good title and against infringement The information in this manual contains only essential hardware concerns for general user and is subject to change without notice Posiflex reserves the right to alter product designs layouts or drivers without notification The system integrator shall provide applicative notices and arrangement for special options utilizing this product The user may find the most up to date information of the hardware from web sites http www posiflex com or http www posiflex com tw All data should be backed up prior to the installation of any drive unit or storage peripheral Posiflex will not be responsible for any loss of data resulting from the use disuse or misuse of this or any other Posiflex product All rights are strictly reserved No part of this documentation may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying or otherwise without prior express written consent from Posiflex Technology Inc the publisher of this documentation Copyright Posiflex Technology Inc 2010 All brand and product names and trademarks are the property of their respectiv
3. on cover option ELECTRICAL Power Source Solenoid Drive for CR 2210 Pulse Amplitude 12 to 24 VDC Pulse Width 100 to 250 msec Pulse Duty Cycle 10 max Max Current Consumption 0 75A 12 VDC 1A 24 VDC AC Adaptor for CR 2214 2215 Input Voltage 120 VAC 10 240 VAC 10 50 60 Hz Output Voltage 12 VAC at1 5A Interface Direct Drive CR 2210 Serial RS232C CR 2214 Baud rate 9600 19200 Parity none Data Bits 8 Stop Bits 1 USB 1 1 CR 2215 Security Code CR 2215 USB PID Drawer Open Sense CR 2210 Drawer open sense circuit shorts when drawer open CR 2214 Pin 9 in DB9 connector goes high when drawer open CR 2215 Through USB driver Part 8 KEYLOCK OPERATION Lock B Physically lock the drawer Open CO Open the drawer by the key Standby vy Automatically open the drawer by POS printer or POS system or interface Keylock signal control STRUCTURE Check Slot Inside CR 2210 2214 2215 Bill tment ill compartmen Adjustable coin compartment Cash Tray Fixed coin compartment Check Storage
4. the cash drawer bottom plate If user lost the key he she can order the key according to this number 5 Signal Cable depend on model Part 2 a For CR 2210 The standard signal cable is 21863018010 which has a 8 pin plug at one end to connect to the cash drawer and a 6 pin modular plug at the other end to connect to the POS system printer This cable serves for most popularly used POS equipment such as Posiflex POS terminals Posiflex POS printers most Epson POS printers most Star POS printers and all other compatibles The user may cut the 6 pin end or order the ready cut cable CCBLA 180A and assemble this free end according to his POS printer specification if the POS printer used utilizes different connection The cable connection on CCBLA 180A is as below Wire color Function Drawer open sense Drawer open sense return 24V to solenoid Drawer kick pulse b For CR 2214 Serial signal RS232 DF9F RJ9 conversion cable 21863259900 21863159900 c For CR 2215 USB cable 21863250800 2 1863 150800 6 Power Source depend on model a For CR 2210 not applicable b For CR 2214 Power adapter 12VAC 1 5A c For CR 2215 Power adapter 12VAC 1 5A INSTALLATION Coin compartment adjust Open the top cover and remove any protective materials such as a piece of PE foam if it exists The coin compartment separator can be removed from and inserted till click into the grooves in adjustable coin compartment zones fo
5. CR 2210 SERIES POSIFLEX CASH DRAWER USER S MANUAL FCC Notes Rev CO This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual may cause interference to radio communications It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules which are designed to provide reasonable protection against interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures to correct the interference Warranty Limits Warranty terminates automatically when any person other than the authorized technicians opens the machine The user should consult his her dealer for the problem happened Warranty voids if the user does not follow the instructions in application of this merchandise The manufacturer is by no means responsible for any damage or hazard caused by improper application About This Manual Posiflex has made every effort for the accuracy of the content in this manual However Posiflex will assume no liability for any technical inaccuracies or editorial or other errors or omissions contained herein nor for direct indirect incidental consequential or otherwise damages including without limitation loss of data or profits resulting from the
6. e holders P N 19230900050 Part 1 E BRIEF INTRODUCTION INTRODUCTION The CR 2210 series is a flip top type cash drawer It provides Aluminum alloy die cast case with zero externally accessible screw FEATURES Flip top design Contemporary style with regular width of 460mm and flat side surfaces Rugged design with no screw to be accessed from outside Advanced electronics that extends the MTBF Mean Time Between Failure Three position lock with automatic spring back function for maximum cash security Check slot with check storage underneath cash tray for non cash or large bill transaction without opening drawer 2 fixed and 4 adjustable total 6 bill compartments fixed and 7 adjustable total 8 coin compartments Partially adjustable in size and number by use of coin compartment separator Provided with various interface selection including direct printer drive dedicated RS232 USB Optional additional removable tray Also optional tray cover with lock WEPOS certified 2color choices Ivory and Black MODEL NUMBER amp INFERFACE Model Number Interface Security Code Power Source CR 2210 Printer drive N A oe Pulse CR 2214 Dedicated RS232 N A 12VAC Adaptor CR 2215 USB USB PID 12VAC Adaptor CARTON CONTENTS 1 Cash drawer pre assembled 2 User s manual 3 Separators of coin compartment 5 pcs 4 Key 2pcs There is a key serial No sticker on
7. face Part 4 CR 2215 1 2 3 4 5 The drawer number PID is default to be 7 Refer to the guidance for Jumper Setting Change below if the PID has to be changed Connect USB type B connector more or less square one of USB cable to the USB connector at rear side of CR 2215 and the type A connector end to USB port of host PC or POS system as shown in drawing above Check the specification of power adaptor on its nameplate Insert the power adaptor into the correct power outlet Insert the output plug to the power jack at rear side of CR 2215 to supply power for drawer kickout Turn the keylock to standby position Install the USB utility driver from Posiflex Product Information CD with Posiflex POS system or visit our web _ sites http www posiflex com or http www posiflex com tw or http www posiflexusa com for latest updates Switch Setting Change for CR 2214 2215 1 2 Use key to open the cash drawer Take out the removable tray and you can find a control board in the bottom The lay out of the control board is illustrated below Zot By switch setting at different positions of JP1 interface selection between RS232 and USB and PID selection can be made Interface select switch position 1 of JP1 defines interface of the cash drawer beside the interface cable used When switch position 1 is ON the
8. r appropriate compartment size Coin Compartment Separator Adjustable Coin Compartment Part 3 CR 2210 1 Connect the 8 pin plug of CR cable to cash drawer and the 6 pin plug to CR port of POS system or POS printer as shown below Rear View 8P Telephone Jack Output to drawe EA CR Cable 21863018010 Cash Drawer With Printer Interface Connect to POS System or Printer 6P Telephone Jack 2 Turn the keylock to standby position CR 2214 1 Connect the 4 pin RJ9 plug of RS232 conversion cable to the RJ9 jack at the rear side of CR 2214 and connect the DB 9 pin connector to RS232 port of host PC or POS system as shown in drawing below 2 Check the specification of power adaptor on its nameplate Insert the power adaptor into the correct power outlet Insert the output plug to the power jack at rear side of CR 2214 to supply power for drawer kickout 3 Turn the keylock to standby position 4 Set the communication protocol of the RS232 port in host system to use baud rate of either 9600 bps or 19200 bps Rear View USB Type B Connector RJ9 4P4C Telephone Jack AC 12V I P Connect to Adaptor RS232 Conversion Cable 21863 159900 21863259900 USB Cable 21863 150800 21863250800 Connect to USB Port of host Connect to RS232 port of host system system For CR 2215 only For CR 2214 only Cash Drawer With RS232 amp USB Inter
9. together Hit the ENTER key then the drawer will open and pass the test 4 Hit CTRL C Press Ctrl and C keys together to return the computer back to the normal display mode In case the cash drawer is connected to serial port other than COM1 please substitute COM1 above to proper port name CR 2215 1 Please find in Posiflex Product Information CDROM or go to Posiflex web sites http www posiflex com or www posiflex com tw or www posiflexusa com for USB Cash Drawer Test Program If you use the Posiflex Product Information CDROM that comes with any Posiflex POS system please go to folder Drivers CR USB and click SETUP EXE to install the USB Cash Drawer Test Program Start up the test program and click STATUS button The drawer status of Open Close or Not present will be displayed under each drawer number as O C or N Use a key to turn the lock to standby position the one marked with sign at middle click the check only the box es under the drawer number s for the drawer s to be tested then click the KICK button The cash drawer will then open and the Open Close Not present status of the tested drawer number will be renewed accordingly If these status are correct the USB interface cash drawer passes the test Part 7 SPECIFICATIONS MECHANICAL Dimensions 460 W x 195 D x 101 5 H mm 18 2 W x 7 7 D x 4 0 H Weight 4 3 Kg Removable tray with a lock
Download Pdf Manuals
Related Search