SL STRIP 10 IP QSG 5th Dec 2014
Contents
1. auto ranging The luminaire contains an auto ranging power supply Each luminaire can draw up to 150 Watts SL STRIP 10 IP LED LUMINAIRES QUICKSTART GUIDE 2 Shewline SL STRIP 10IP LED Luminaire QuickS rende AN WARNING Maximum amount of units that may be daisy chained is A 11 units 120VAC 15 Amps or B 20 units 230VAC 15 Amps Refer to Tablel 1for detailed information at various voltages AN Note For wiring of AC input connector refer to Connecting SL STRIP 10IP LED Luminaire to AC Power Table 1 1 SL STRIP 10 IP LED Luminaire Voltage vs Current 220 240 AN WARNING These figures are based on the Maximum Allowable Input Current of 15 Amps and the maximum power supply limit of 150 Watts Do not overload circuits AN IMPORTANT AC POWER CONNECTION NOTES Wausing the daisy chain connection method ONLY connect SL STRIP 10IP LED Luminaires to AC Output Connection of SL STRIP 10IP LED Luminaires DO NOT CONNECT OTHER TYPES OF LUMINAIRES OR DEVICES Usaly use approved cable types Do not overload circuits Do not connect SL STRIP 10IP LED Luminaire to dimmed circuits The MAXIMUM allowable number of SL STRIP 10 IP LED Luminaire which can be daisy chained on one 15A power feed are listed in Table 1 1 DO NOT EXCEED Connecting Power Units can be powered in one of two ways Direct connection to an AC power source using an AC input cable For wiring of AC input connector refer to Connecting SL STRIP 10 IP LED L2. QUICKSTART GUIDE Shewline QuickStart Guide SL STRIP 10IP LED Luminaire About Quickstart Guide This Quickstart Guide is intended for a knowledgeable user to unpack install and use SL STRIP 10IP LED Luminaires in a short time period For the complete manual in PDF format please visit our web site at www philips com showline and click the user manual download link on the product page The complete manual provides you all information related to accessories menu structures DMX channel mapping modes and care for your new luminaire Included Items Each SL STRIP 10 IP LED Luminaire includes the following items SL STRIP 10 IP LED Luminaire QuickStart Guide this document Figure 1 1 Included Items AN Warnings and Notices When using electrical equipment basic safety precautions should always be followed including the following e READ AND FOLLOW ALL SAFETY INSTRUCTIONS Do not mount near gas or electric heaters Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition Do not use this equipment for other than intended use Refer service to qualified personnel SAVE THIS DOCUMENT FOR FUTURE REFERENCE READ COMPLETELY BEFORE INSTALLING AND USING PR
3. 12 device to be controlled Mounting Luminaire SL STRIP 10 IP LED Luminaires are provided with the ability to fix the unit on the Mount assemblies by the tilt knobs 1f the units are mounted in a hanging application it is recommended and may be required by local and national safety codes to use and install a safety cable sold separately When hanging the fixture be sure to leave enough space around the luminaire to allow proper uninterrupted airflow for a safety cooling and positioning Mount Assembly x2 Tilt Knob x2 SL STRIP 10 IP LED LUMINAIRE QUICKSTART GUIDE 4 Shewline SL STRIP 10 IP LED Luminaire QuickS rende Hanging Application SAFETY CABLE Is sold separately and recommended for all hanging installations and may be required by national and local codes Use the for safety cable anchor points for this fixture Safety Anchor point Figure 1 3 Mounting Luminaire LCD Display and Menu System SL STRIP 10 IP LED Luminaire The SL STRIP 10 IP LED Luminaire s LCD Display and Menu System provides local control for accessing the following fixture s settings Effects Chases preloaded and user defined Timing Status e Fixture Settings o DMX Setting Note If there are multiple luminaires in a system changes would need to be made at each LCD Menu as desired For SL STRIP 10IP LED Luminaire menu structure please refer to the complete user manual 5 SL STRIP 10 IP LED L
4. ODUCT AN WARNING You must have access to a mains circuit breaker or other power disconnect device before installing any wiring Be sure that power is disconnected by removing fuses or turning the main circuit breaker off before installation Installing the device with power on may expose you to dangerous voltages and damage the device A qualified electrician must perform this installation WARNING Refer to National Electrical Code and local codes for cable specifications Failure to use proper cable can result in damage to equipment or danger to personnel WARNING This equipment is intended for installation in accordance with the National Electric Code and local regulations It is also intended for installation in indoor applications only Before any electrical work is performed disconnect power at the circuit breaker or remove the fuse to avoid shock or damage to the control It is recommended that a qualified electrician perform this installation Service and Maintenance For all service and maintenance issues please contact your local Showline office or an Authorized Service Center Power Requirements The SL STRIP 10 IP LED Luminaire operates on AC input voltages from 110 to 240 VAC AN WARNING This unit does not contain an ON OFF switch Always disconnect power input cable to completely remove power from unit when not in use AC Power Operation When connected to an AC source the unit operates on 110 to 240 volts AC 10
5. Shewline SL STRIP 10 IP LED LUMINAIRE 0 O E 0 5 U N pS O Shewline SL STRIP 10 IP LED Luminaire QuickStart Guide Showline Offices Dallas Auckland 10911 Petal Street 19 21 Kawana Street Dallas TX 75238 Northcote Auckland 0627 Tel 1 214 647 7880 New Zealand Fax 1 214 647 8030 Tel 64 9 481 0100 Fax 64 9 481 0101 Asia Europe Unit C 14 F Roxy Industrial Centre Rondweg zuid 85 No 41 49 Kwai Cheong Road Winterswijk 7102 JD Kwai Chung N T Hong Kong The Netherlands Tel 852 2796 9786 Tel 31 0 543 542516 Fax 852 2798 6545 www philips com showline The material in this manual is for information purposes only and is subject to change without notice Showline assumes no responsibility for any errors or omissions which may appear in this manual For comments and suggestions regarding corrections and or updates to this manual please contact your nearest Showline office El contenido de este manual es solamente para informaci n y est sujeto a cambios sin previo aviso Showline no asume responsabilidad por errores o omisiones que puedan aparecer Cualquier comentario sugerencia o correcci n con respecto a este manual favor de diryirlo a la oficina de Showline m s cercana Der Inhalt dieses Handbuches ist nur ftir Informationszwecke gedacht Aenderungen sind vorbehalten Showline uebernimmt keine Verantwortung f r Fehler oder Irrtuemer die in diesem Handbuch auftreten F r Be
6. UMINAIRE QUICKSTART GUIDE Shewline QuickStart Guide SL STRIP 10 IP LED Luminaire LCD Display and Menu System Operation The LCD Display Menu system consists of several categories Use the MODE Button to access and make changes to the menu items When the desired menu item is reached press the desired MENU Button to display the menu options and to navigate and configure the menu options as required To navigate and access menu settings selections Step 1 Make sure unit is powered and turned on Step 2 Press the desired button as shown in Figure 1 4 to access menu categories Step 3 Use UP DOWN buttons to navigate through the various options and settings Step 4 Make changes as desired LCD Display MODE DOWN MENU o O Q Figure 1 4 Menu System SL STRIP 10IP LED LUMINAIRE QUICKSTART GUIDE 6 Shewline Dallas 10911 Petal Street Dalls TX 75238 Tel 1 214 647 7880 Fax 1214 647 8031 Asia Unit C 14 F Roxy Industrial Centre No 41 49 Kwai Cheong Road Kwai Chung N T Hong Kong Tel 852 2796 9786 Fax 852 2798 6545 Auckland 19 21 Kawana Street Northcote Auckland 0627 New Zealand Tel 64 9 481 0100 Fax 64 9 481 0101 Europe Rondweg Zuid 85 Winterswijk 7012 JD The Netherlands Tel 31 0 543 542516 2014 Philips Group
7. merkungen und Verbesserungsvorschlaege oder Vorschlaege in Bezug auf Korrekturen und oder Aktualisierungen in diesem Handbuch moechten wir Sie bitten Kontakt mit der naechsten Showline Niederlassung aufzunehmen Le mat riel d crit dans ce manuel est pour information seulement et est sujet a changements sans pr avis La compagnie Showline n assume aucune responsibilit sur toute erreur ou ommission inscrite dans ce manuel Pour tous commentaires ou suggestions concernant des corrections et ou les mises a jour de ce manuel veuillez s il vous plait contacter le bureau de Showline le plus proche Note Information contained in this document may not be duplicated in full or in part by any person without prior written approval of Philips Its sole purpose is to provide the user with conceptual information on the equipment mentioned The use of this document for all other purposes is specifically prohibited CAUTION Possible hazardous optical radiation may be emitted from the products described herein Do not stare directly into light sources May be harmful to the eyes Note The light source contained in this luminaire shall only be replaced by the manufacturer authorized service center or suitably qualified person Document Number SL STRIP 10 IP LED Luminaire QuickStart Guide Version as of 24 004 3745 00 Rev1 0 SL STRIP 10 IP LED Luminaire QuickStart Guide 2014 Philips Group All rights reserved 1 SL STRIP 10 IP LED LUMINAIRE
8. uminaire to AC Power Connection from the AC output of another SL STRIP 10 IP LED Luminaire When using this method it is very important not to connect any other type of equipment AN WARNING Only connect other SL STRIP 10 IP LED Luminaire to the AC Output Thru connector ofa SL STRIP 10 IP LED Luminaire Connecting SL STRIP 10 IP LED Luminaire to AC Power Table 1 2 AC Input Connections describes how to connect power to your SL STRIP 10 IP LED Luminaire Field wiring of the SL STRIP 10 IP LED Luminaire is straight forward A total of 3 wires conductors is supplied to this unit Table 1 2 AC Input Connections Blue Neutral Green Yellow Ground Earth 3 SL STRIP 10IP LED LUMINAIRES QUICKSTART GUIDE Shewline QuickStart Guide SL STRIP 10 IP LED Luminaire AC Input and Output Connections SL STRIP 10IP amp 40 C 0 2mh we LY CE wes X PHILIPS AC Input RDM DMX In RDM DMX Out AC Output Figure 1 2 AC Input amp Output Connections Connecting to the DMX Network Table 1 3 DMX 512 Connections Basic DMX512 installation consists of connecting multiple SL STRIP 10IP LED Luminaires together up to 32 luminaires in daisy chain fashion A cable runs from the control console or DMX512 control source to the DMX connector on the first SL STRIP 10IP LED Luminaire Another cable runs from the other DMX connector on the first unit to a DMX connector on the next SL STRIP 10IP LED Red Luminaire or DMX5
Download Pdf Manuals
Related Search