SOLAR-100
Contents
1. AAMPROBE SOLAR 100 Solar Power Meter Users Manual Mode d emploi Bedienungshandbuch Manual d Uso Manual de uso SOLAR 100 Solar Power Meter Users Manual July 2009 Rev 1 2009 Amprobe Test Tools All rights reserved Printed in China Limited Warranty and Limitation of Liability Your Amprobe product will be free from defects in material and workmanship for 1 year from the date of purchase This warranty does not cover fuses disposable batteries or damage from accident neglect misuse alteration contamination or abnormal conditions of operation or handling Resellers are not authorized to extend any other warranty on Amprobe s behalf To obtain service during the warranty period return the product with proof of purchase to an authorized Amprobe Test Tools Service Center or to an Amprobe dealer or distributor See Repair Section for details THIS WARRANTY IS YOUR ONLY REMEDY ALL OTHER WARRANTIES WHETHER EXPRESS IMPLIED OR STAUTORY INCLUDING IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY ARE HEREBY DISCLAIMED MANUFACTURER SHALL NOT BE LIABLE FOR ANY SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES ARISING FROM ANY CAUSE OR THEORY Since some states or countries do not allow the exclusion or limitation of an implied warranty or of incidental or consequential damages this limitation of liability may not apply to you Repai2. When the light sensor cover is not attached CAP is indicated Make sure that it is attached If performing the zero adjustment after powering on several digits may not disappear In this case perform the zero adjustment again To Measure House s Windows Solar Insulation Measure the solar insulation effect of your house s windows Close the window Press the oy button on your SOLAR 100 solar power meter and 00 0 comes up on the screen Put the device close to the window and aim it at the sun Compare the value against that acquired when the window is closed and the device is placed at the same position in order to understand the window s heat efficiency Picture 2 Max Min Button When you test in W m2 BTU ft2 h press the button to display the max or min reading Press and hold the button for 1 second to allow the device to read the max value Press the button one more time to read the min value Press and hold the button for more than 1 second and the max and min come off When the button is functional the Ce button is disabled BTU ft2 h W m2 Button Press the Co button to turn ON the power and put the device to operating mode The screen displays BTU ft2 h Press the E button to switch from BTU ft2 h to W m2 To select a different unit just press this button once again H Data Hold Button Press the gt button to go into hold mode
3. and gt appears on the screen to allow you to read the data Press this button once again to deactivate it Auto Range Button Press the power button to turn ON the power and put the device to operating mode If 1999 comes on the screen it suggests the device will become overloaded or has become overloaded OL In this case press the Ce button and 199 or your acquired value then comes up Picture 2 SPECIFICATION Battery Life Approx 100 hr Accuracy Typically within 10W m2 3 BTU ft2 h or 5 whichever is greater in sunlight Additional temperature induced error 0 38W m2 C 0 12 BTU ft2 h C from 25 C Operating temp amp RH 5 C 40 C below 80 RH Storage temp amp RH 10 C 60 C below 70 RH Display 3 1 2 digits LCD with maximum reading 1999 Sampling Time Approx 0 25 second Resolution 0 1W m2 0 1 BTU ft2 h Accuracy lt 3 Over input Display shows Range 1999W m 2 634 BTU ft 2 h Dimensions 132 L x 60 W x 38 H mm Weight Approx 150g EMC This instrument is EMC compliant and has undergone compatibility tests according to EN61326 1 2006 EMC Conforms to EN61326 1 This product complies with requirements of the following European Community Directives 89 336 EEC Electromagnetic Compatibility and 73 23 EEC Low Voltage as amended by 93 68 EEC CE Marking However el
4. E 267 7623 Tel 905 890 7600 Non Warranty Repairs and Replacement Europe European non warranty units can be replaced by your Amprobe Test Tools distributor for a nominalv charge Please check the Where to Buy section on www amprobe com for a list of distributors near you European Correspondence Address Amprobe Test Tools Europe In den Engematten 14 79286 Glottertal Germany Tel 49 0 7684 8009 0 Correspondence only no repair or replacement available from this address European customers please contact your distributor SOLAR 100 Solar Power Meter O A AMPROBE soLar 100 MIN D H 999 1124 Btul ft h Solar Power Meter Si O Light Sensor Power Button Display LCD Auto Range W m2 BTU ft2 h Switch Button Data Hold Button Lock Up Max Min Button CONTENTS Eh del 2 Warning and Precautions concen 2 UNPACKING AND INSPECTION INTRODUCTION 3 OPERATION encia 4 SPECIFICATION A 7 MAINTENANCE AND REPAIR 8 BATTERY REPLACEMENT 4 8 SYMBOLS Caution Refer to the explanation in this Manual A Conforms to relevant Australian standards Complies with European Directives _ Do not dispose of this clamp meter as unsorted municipal waste Contact a qualified recycler for d
5. ectrical noise or intense electromagnetic fields in the vicinity of the equipment may disturb the measurement circuit Measuring instruments will also respond to unwanted signals that may be present within the measurement circuit Users should exercise care and take appropriate precautions to avoid misleading results when making measurements in the presence of electronic interference MAINTENANCE AND REPAIR If there appears to be a malfunction during the operation of the meter the following steps should be performed in order to isolate the cause of the problem 1 Check the battery Replace the battery immediately when the symbol appears on the LCD 2 Review the operating instructions for possible mistakes in operating procedure Except for the replacement of the battery repair of the meter should be performed only by a Factory Authorized Service Center or by other qualified instrument service personnel The front panel and case can be cleaned with a mild solution of detergent and water Apply sparingly with a soft cloth and allow to dry completely before using Do not use aromatic hydrocarbons or chlorinated solvents for cleaning BATTERY REPLACEMENT When the symbol is displayed batteries need replacement Unscrew the battery cover and remove the battery Insert new battery of the same type 1604 JISOO6P IEC6F22 observing the proper polarity re screw the battery cover and repositi
6. isposal AWarning and Precautions For your own safety and to avoid damaging the instrument follow the procedures described in this instruction manual and read carefully all notes preceded by this symbol A When taking measurements Avoid doing that in humid or wet places or using in rooms where explosive gas combustible gas steam or excessive dust is present Avoid doing that if you notice anomalous conditions such as breakages deformations fractures leakages of battery liquid blind display etc Operating environment for indoor use expose to pollution level Do not put this device in direct sunlight or where it is hot and or damp Remember to turn OFF the power after use For long storage remove the battery to prevent the battery from leaking to cause damage to the parts inside This is a precision device During use or storage do not go beyond its spec to prevent any possible damage or danger UNPACKING AND INSPECTION Your shipping carton should include 1 SOLAR 100 Solar Power Meter 1 9 volt battery 1 User manual If any of the items are damaged or missing return the complete package to the place of purchase for an exchange INTRODUCTION The SOLAR 100 measures the solar energy and radiation the typical application for this model are Transmission measurement is most suitable for measuring the effectiveness of the solar film Solar radiation measurement Car windows light intensity meas
7. on the protective holster e Type 9V NEDA1604 JISOO6P IEC6F22 observing the proper polarity Visit www Amprobe com for e Catalog Application notes Product specifications e User manuals 6 Please Recycle
8. r All test tools returned for warranty or non warranty repair or for calibration should be accompanied by the following your name company s name address telephone number and proof of purchase Additionally please include a brief description of the problem or the service requested and include the test leads with the meter Non warranty repair or replacement charges should be remitted in the form of a check a money order credit card with expiration date or a purchase order made payable to Amprobe Test Tools In Warranty Repairs and Replacement All Countries Please read the warranty statement and check your battery before requesting repair During the warranty period any defective test tool can be returned to your Amprobe Test Tools distributor for an exchange for the same or like product Please check the Where to Buy section on www amprobe com for a list of distributors near you Additionally in the United States and Canada In Warranty repair and replacement units can also be sent to a Amprobe Test Tools Service Center see address below Non Warranty Repairs and Replacement US and Canada Non warranty repairs in the United States and Canada should be sent to a Amprobe Test Tools Service Center Call Amprobe Test Tools or inquire at your point of purchase for current repair and replacement rates In USA In Canada Amprobe Test Tools Amprobe Test Tools Everett WA 98203 Mississauga ON L4Z 1X9 Tel 877 AMPROB
9. urement Optimal incident angle for the solar panel Measurement of the sun s transmission through transparent and film glass Convenient no need to adjust data displayed clearly OPERATION To Measure Car s Headlights or Car Windows Solar Insulation Use a screw driver to adjust the hole of 0 ADJ for the zero adjustment if any digits is appear If performing the zero adjustment after powering on several digits may not disappear In this case perform the zero adjustment again Measure your car s headlights Turn ON your car s headlights Then turn ON the SOLAR 100 meter and 00 0 appears on the screen Put the device down close to the headlights Switch between high beam and low beam and light intensity values appear on the screen Both the right and left headlights must be tested Note the values and put them in your car for reference Picture 1 Measure the effect of solar insulation of your vehicle s windows Press the button to turn ON the SOLAR 100 meter 00 0 appears on the screen Aim the device at the sun and close to a window and the intensity appears on the screen Open the window and aim the device at the sun Compare the value against that acquired when the window is closed to understand the efficiency of the window s solar film Test your new car and preserve the measurements in it After that test it at least once every year Picture 1 Picture 1 NOTE
Download Pdf Manuals
Related Search