SPRT SP-POS88ⅤThermal Receipt Printer User`s Manual
Contents
1. Fig 2 1 Printer Appearance 2 2 Paper Installation 2 2 1 Paper Loading POS88 V adopts 79 5mm width thermal paper roll Steps of Loading Thermal Paper Are as below Hold down the upper cover button on the left side open the movable upper cover draw a certain length of the paper roll put the paper end on the print head close the upper cover and press it downwards lightly Caution 1 Pay attention to the direction of loading paper make the printing surface face to the print head 2 Please don t feed or draw the paper forwards or backwards with hands 3 Keep clean of the print head avoid to influence the printing quality 2 2 2 Solution to Paper Jam If cutter jam turn off the power and turn on again the cutter will be back to original position If paper jam open the paper strage cover and take out the paper If the cutter can not be back to the original position open the cover of it and turn the white plastic gear by the direction suggestive on the cutter by hand to make the cutter be back to the original position 2 3 Interface 2 3 1 Serial Interface The serial interface of SP POS88 V printer is compatible with RS 232C supports DTR DSR and XON XOFF handshaking protocols uses DB25 socket female The pin order of the serial port is as Fig 2 2 shows Fig 2 2 Pin Order of Serial Port The pin assignment of serial interface is shown in Fig 2 3 Description Signal Source Direction ope fo E eee 2 TXD Out2. as below Pin Signal Direction No 1 Chassis Ground 2 Cash drawer driver Out signal 1 4 24VDC 5 Cash drawer driver Out signal 2 Signal ground 3 Cash drawer on off In status signal 2 3 4 Power Connection POS88 V uses the external power supply adopter as 24V 10 2A power socket is A 1009 3P model as Fig 2 10 shows Fig 2 8 Power Socket The pin assignment is as below 24VDC 2 4 Buttons and Indicators There is one button and three indicators on POS88 V printer FEED J is paper feeding button the function of its enabling or disabling the button on off can be set by print command when the button is enabled press FEED button then the paper presenting driver starts up and paper fed into the printer release FEED button paper feeding stops The green POWER light is the power indicator red ERROR light is status indicator it is dark when the printer works normally while it flashes when reporting an abnormal emergency as the following form shows Error Indicator and Buzzer Description e ooo rl A ER flashes uplift overheat when the print head cools Position Error indicator blinks check if there is paper a rr AI When any error shown above occurs pin nFault of parallel change to 0 level and send 1 bit wrong code through serial TXD by itself it can also send out the printer state by answer the ESC v command Red indicator of Paper Out is the paper out indicatoe Whe
3. SPRT SP POS88 V Thermal Receipt Printer User s Manual Ver 1 00 Beijing Spirit Technology Development Co Ltd Content Tao ABTIN KO 0 eil 2 Chapter Feature and PerfotTmanCe oooooooo Wo Wc 2 1 1 Print Performance ee NB i Li 2 WZ Pat Paper ono ane orig ieri 2 An On Aa OR E SERIO OO 3 VA Man Tab allea 3 1 5 Print Control Commands ooooo 3 TOP OWEL SUPPLY ecir e nana atau 4 1 7 Operation Enviton MEN enak heetn onani akn kah 4 1 8 Outline Dimentica 4 lLSModel Classificationi NN NB 4 Chapter 2 Operation Specification WWoc 5 2 1 Printer IA PPC Al ACS bana NA kan an NAN 5 2 2 Paper Insta AON acari 6 225 Paper Oa acilia 6 2 2 2 Solution to Paper Jam sintesis anta 7 PREA LOINS aa KA E hi ilo eli ul 8 2 3 1 Serial Interface wmwwewmmmnnwewa 8 Z9 2ParallelInterface arl 9 2 3 3 Cash Drawer InterfatE sena ai 11 2 3 4 Power CONNEC IO Mies bk nb NN 12 2 4 Buttons and Indicators ii 12 DI Cella is 14 2 6 Hexadecimal Puniet ara 14 Introduction POS88 V printer is a new type line thermal printer it features in fast speed print low print noise high reliability perfect print quality and ribbon needless avoiding the vexation of regular maintenance POS88 V printer small in outline dimension simple operation and extensive application especially suitable for commercial cash register PC POS bank POS and
4. ading occurs at falling edge 2 DI In These signals represent the Ist bit to 8th bit of the parallel data representatively 3 D2 In each signal is at HIGH level when data is 4 D3 In logic 1 and LOW when data is logic 0 5 D4 In 6 D5 In A D6 In 8 D7 In 9 D8 In 10 ACK Out Answer pulse LOW level signal indicates that data have already been received and the printer gets ready to receive the next data 11 BUSY Out HIGH level signal indicates that the printer is BUSY and can not receive data 12 PE Out HIGH level signal indicates that paper is end 13 SEL Out Pulling up to HIGH level signal by a resistor 17 FG Signal Cover 18 Logic H Logic 1 level 32 nFault Out Low level means the printer is at fault 14 15 17 18 34 36 NC No connection 16 19 30 GND Grounding logical 0 level 33 35 5V 5V power Fig 2 5 36Pin assignment of parallel interface Note 1 In denotes input to the printer Out denotes output from the printer 2 Signal level is TTL standard The timing chart for interface signal of parallel interface is as Fig 2 6shows int at ata i 0 5 ps i 0 5 ps i 0 5ps i 0 5 ps i i min min min mini Fig 2 6 Signal Timing Chart of Parallel Interface 2 3 3 Cash Drawer Interface The cash drawer interface of POS POS88 V adopts RJ 11 6 pin socket as Fig 2 7 shows Fig 2 7 Cash Drawer Interface The pin assignment is
5. all kinds of receipts print Warning This is a class A product In a domestic environment this produ ct may cause radio interference in which case the user may be required to take adequate measures Chapter 1 Feature and Performance 1 1 Print Performance e Print method direct thermal Print paper width 79 5 0 5mm Print density 8 dots mm 576 dots line Print speed approx 250mm sec Reliability 1 Print head life 100km Using condition Print 12 x 24 ASCII characters print 50 lines each time intermittent print repeatedly Each dot line printing at the same time should not exceed 25 each character line and one dot vertical printing repeatedly should not exceed 11 times Use specified thermal paper 2 Cutter life 500 000 cuts Using condition less than 30 cuts minute 9 Valid print width 72mm 1 2 Print Paper Thermal paper roll model TFSOKS E Japan paper co ltd AFS0KS E JUJO THERMAL Thermal paper roll Width 79 5 0 5mm Outer Diameter 80mm max Inner Diameter 13mm min Thickness 0 06mm 0 08mm 1 3 Print Font ANK Character Set 12x24 dots 1 5 W X3 00 H mm GB GB2312 80 Chinese 24x24 dots 3 00 W x3 00 H mm 1 4 Interface RS 232C Serial Interface DB 25 socket female supports XON XOFF and TR DSR protocols Baud rate 2400 4800 9600 19200 38400 57600 115200bps adjustable Data structure Istart b
6. it 7 or 8 data bits 1 stop bit Parity checking no parity or odd even parity optional Parallel Interface 36 pin 8 bit parallel interface BUSY ACK handshaking protocol TTL signal level Ethernet Interface Normal ethernet interface USB Interface USB interface 9 Cash Drawer Control DC24V 1A 6 pin RJ 11 socket 1 5 Print Control Commands e Character print commands support double width double height print of ANK characters user defined characters and Chinese characters the character line spacing is adjustable 9 Graphics print commands support the print of bit map graphics and download bit map graphics with different density GS bar code print commands support UPC A UPC E EAN 13 EAN 8 CODE39 ITF CODEBAR CODE93 CODE128 PDF417 QR bar code print 1 6 Power Supply e DC24V 10 2A A 1009 3P power socket 1 7 Operation Environment Operation temperature 5 50 C Relative humidity 10 80 e Storage temperature 40 55 C Relative humidity 10 90 C 1 8 Outline Dimension e200 L mmX 150 W mmx 139 H mm 1 9 Model classification Chapter 2 Operation Specification 2 1 Printer Appearance Paper Cover sm ta p Power Indicator green l Status Indicator red Paper end Indicator red Paper Feed Button FEED Decap Button Paper out Slot Cutter Cover Power Switch Cash drawer interface Interface Socket lb an Power Socket TT
7. n there is no paper in printer head it will light and it is off under normal status 2 5 Self test The self test will check the condition of printer if the printer prints out the self test receipt correctly it means the printer works normally except interface with host Otherwise it needs to repair The self test will print out 96 ANK characters defalut code page name of Chinese Characrer library interface setting and software version Way of self test hold down FEED button and turn on the power self test begins automatically at this moment 2 6 Hexadecimal Printing Turn on the printer according to the step below it will enter the mode of Hexadecimal Printing 1 Open the cover 2 Hold down FEED button and connect with power 3 Close the cover the printer will print out 3 lines as below Hexadecimal Dump To terminate hexadecimal dump Press FEED button three times This means the printer has entered hexadecimal printing mode and under this mode all of the input will be printed out as hexadecimal number feed one line with single click of FEED button after 3 times it will print out Completed and exit hexadecimal printing mode
8. put Printer Printer transmits control code X ON X OFF and data to host Printer receives data from host RTS Output Printer The same with 20pins DTR signal DSR Input Host Signal MARK means the host is busy and can not receive data Signal SPACE means the host is ready to receive data 20 DTR Output Printer Signal MARK means the host is busy and can not receive data Signal SPACE means the host is ready to receive data Fig 2 3 The pin assignment of serial interface Note 1 Source denotes the source that signal come from 2 Logical signal level is EIA The baud rate and data structure in serial interface mode is 9600bps 8 bit data bits no parity bit and 1 stop bit The serial interface of SP POS88 V can be connected to standard RS 232CRS 232C interface When it is connected to IBM PC or its compatible machine connection can accord to Fig 2 4 Printer IBM PC Printer IBM PC 25PIN Socket DB9 Socket 25PIN Socket DB25 Socket Fig 2 4 Connection between SP POS88 V and IBM PC Serial Interface Sketch Map 2 3 2 Parallel Interface The parallel interface of POS88 V printer is compatible with CENTRONICS supports BUSY or ACK handshaking protocol uses 36pin CENIRONICS socket female The pin assignment of DB25 parallel interface is as Fig 2 5 shows Pin No Signal Direction Description 1 STROBE In Strobe pulse to latch data Re
Download Pdf Manuals
Related Search