- AD INSTRUMENTS
Contents
1. Switch AD INSTRUMENTS AD620 user manual 4 Description of Software Menu There are 6 pages of the software menu function selection parameter set maintenance set record check and operation guide description of subpage is as follows Are Test By doing Arc Test it will judge whether the current arc power is suitable for the fiber and environment or not Prepare fiber place the fiber in the V groove choose arc test and then enter arc test program and there will be a report after the arc test finished If it shows arc strong or arc weak the machine will automatically adjust arc power to make the following arc test to be arc ok Performing Arc test is a very important method to keep the machine at a well working condition Arc test has to be performed in the following situations to avoid bad splice Replace of electrode Dramatic change of temperature humidity and air pressure Different fibers to be spliced Several times use of Electrode Splicing db loss high without reason Distortion of fiber image after splicing Cleaning arc time There is a transient arc for cleaning the fiber after fiber is pushed into the screen it can be modified by this program Splicing mode select There are 7 modes can be selected SM MM50 MM62 5 DS NZDS ERBIUM USER DEFINE the specific parameter of the splicing parameter menu will be changed accordingly Tension Test set After open the wind protector the machine will tension test or not based on2. foot Place the holder with fiber in side to the holder base make sure fiber is in V groove Put down fiber presser foot softly and close wind protector Press splicing button Three Alignment adjustment If fiber core shift bigger than the threshold set splicer will stop splice and wait for manual adjustment Core alignment manually by adjusting the wheel during adjustment offset data will keep decreasing splicer will beep when core alignment succeed Eface L1 0 RALAN 0 Eface L1 0 Eface ROMI Zi EI Alignment offset Before adjustment After adjustment Four Heating operation Open wind protector take out spliced fiber For drop cable please use the professional tool to take out the fiber Press reset button for next splicing If necessary Move the protection sleeve to cover the splicing point Put fiber in heater AD INSTRUMENTS AD620 user manual Press heating button Splicing and heating finish Need to change the left side base of the heater if heat drop cable or splice on connector 7 Charging of Machine The fusion splicer is equipped with the dedicated charger other chargers are not allowed It can be charged when power on or power off Red indicator light mean fusion splicer is under charging green mean charge fully 8 Standard package and optional 1 Fiber cleaver 2 drop cable stripper 3 Stripper 4 Holder Multip
3. this set Heating time Heater will heat according to the time set after pressing the heat button Pressing heating button during heating operation it will stop heat Auto start set If this item is OPEN after close the cover in stand by status the machine will start splice automatically Parameter Set I Arc power This parameter has the function over cleaning arc pre arc splicing arc arc again it can be set from 10 100 AD INSTRUMENTS AD620 user manual Pre arc time it is time between the start of arcing and start of forward Arc time it is the continuous arc time after forward Overlap length the forward length during arc process Arc again After splicing pressing arc button the machine will arc again Angle threshold During splicing process if the fiber angle is greater than this parameter PAUSE will be automatically started Even if PAUSE I is in off condition Note Changing arc power and arc time has an affect on arc test result Parameter set II Push speed it decides motor speed and reset speed Alignment gap the distance between the end face of left and right fiber after aligned Gap position the position of end face after fiber aligned it is set in the mid of the screen usually When the arc position is not in the mid of the screen can be verified by the result of arc test this parameter can be modified to make the gap position and arc position stay in same Alignment offset If the alignmen
4. AD INSTRUMENTS AD620 user manual FTTHARC FUSION SPICER AD620 Read this instruction manual carefully before operating the equipment Adhere to all safety instructions and warnings contained in this manual Keep this manual in a safe place AD INSTRUMENTS AD620 user manual Content Sikhs Miroduc ons sees ol a ns S2 JSPCCWICAUONS anaa bent hes chet denne 3 Description of Operation UMItS cccecseeeeeeseeeeeeees 4 Description of software menu 5 Switch on switch off and Stand by of Machine 6 Basic procedure of splicing ST Charems Of Machine sesame an a a eee 8 Standard package S 9 Safety Operational Norms 10 Warnings and Cautions for transportation 11 Periodical replacement of components AD INSTRUMENTS AD620 user manual S 1 Introductions It is a light weight small and fast FTTH Fusion Splicer which is designed to splice bare fiber pigtail patch cord Optical fiber drop cable and make of SC FC LC connector on the spot by changing different fiber holders equipped It is an ideal tool for the splicing of fiber network terminal which is able to work in narrow and small room Picture as follows AD INSTRUMENTS AD620 user manual 2 Specifications e Applicable fibers SM MM DS NZ DS G655 G657 and others Fiber Diameter Cladding Diameter 80 150 um Coating Diameter 100 1000 um e Splice Time 8Sec e Average splice loss 0 01dB MM 0 02dB SM 0 04dB D
5. S NZDS G 655 G 657 Return loss 60db Tension test 2 0N e Protection sleeve length 25mm 40mm 50mm Tube heat Time 35 seconds e Splicing program Parameter modifiable e Alignment Core Alignment e Language English and Spanish Other language optional e Fiber Holder Replaceable and Suitable for the Splice of bare fiber pigtail patch cord Optical fiber drop cable and SC FC LC connectors e Display Color 3 5 Inch TFT e Magnification 220 Interface USB Uart suitable for data download and software update e Splice Memory 10000 e Operating Temp 15 C 50 C e Storage Temp 40 C 80 C e Window Protection Max wind velocity of 15m s DC output 12V 2A Power for external heater light or hot jacket stripper Internal Battery 12V 6Ah more than 120 times of continuous splices and heats Dimension 120mm L 120mm CW 115mm H e Weight 1 7KG Include battery AD INSTRUMENTS AD620 user manual 3 Description of operation units Panel and Wind Protector bo or 6 12 QUIT MENU 1 Wind Protector Magnet 2 Wind Protector 3 Electrode Cover Plate 4 Holder Base 5 Electrode 6 Key Board 7 light 8 Fiber Presser 9 Heating indicator light 10 Electrode Base 11 V Groove 12 Alignment wheel Description of side outlet box 1 Charging input port 2 USB interface 3 DC output port Key board Menu Confirm Exit Return FREJ Up Down Modity na Splice Re arc T Heating A Reset
6. cause burn 10 Only electrodes supplied by manufacturer can be used 11 Is PAS Repair and adjustment can only be operated by the professional technician or engineer improper repair may cause fir and electric shock 10 Warnings and cautions for transportation Avoid strong shock or crash because fusion splicer is precision instrument and the mechanical components were precisely adjusted and aligned otherwise damage will be caused make sure use the equipped carton to store or transport the machine Do not put fusion splicer in a unstable or unbalanced position otherwise fusion splicer may be damaged in case the fusion splicer loose balance 11 Periodical replacement of component Replacement of electrode Power off fusion splicer loss the two screws which fastening the cross shaped slot take out electrode cover and screws take out electrode Change new electrodes and put the end face of the plastic top of the electrode on the copper plate Pressing electrode by electrode cover tighten two screws there should be a 0 1mm gap between electrode cover and copper plate once screwed do not make over deformation of the electrode cover Repeat 1 5 to change another electrode Replacement of heater Switch off fusion splicer cooling heater to room temperature Open left and right plate Dismantle two M2 5 screws by allen wrench Take off heater softly and pull off power plug Change a new heat
7. er plug the power line Tightening heater to fusion splicer panel by two M2 5 screws AD INSTRUMENTS AD620 user manual
8. le 5 Electrode 6 Cooling tray 7 Charger 8 ll Fiber take out tool 9 Instruction Manual 9 Safety operation Norms 1 Prohibiting to using fusion splicer in the environment with inflammable explosive liquid or gas otherwise electrode arc may cause fire or explosion 2 Do not operate machine if there are moisture condense on the machine otherwise the machine will be damaged 3 Avoid strong shock or crash because the mechanical components were precisely adjusted and aligned otherwise damage will be caused make sure use the equipped carton to store or transport the machine AD INSTRUMENTS AD620 user manual 4 Sy Do not use any other chemicals but alcohol to clean lens V Groove holders LCD monitor etc otherwise it will cause blurred imaging dirt damage corrosion Do not touch electrode while fusion splicer is working otherwise the high pressure and temperature generated by electrode will cause electric shock and burn Switch off fusion splicer while changing electrodes Do not dismantle fusion splicer and charger Only use the equipped charger to charge battery otherwise may cause damage to fusion splicer and operators Switch off fusion splicer in case liquid water or other external stuff screw entered the machine otherwise damage to the machine will be caused Take out fiber carefully after heating finished do not touch the protection sleeve and heater since the high temperature will
9. onnector which need strip Strip fiber protective layer by CFS 2 Stripper and retain 1 mm Clean fiber Place the cleaned fiber to the fiber holder Place connector locating pin into holder front slot AD620 user manual AD INSTRUMENTS Place connector locating pin into holder back slot Place the holder to AD 105H fiber cleaver for cut Cut finished Stripping diagram not less than 1 8mm AN Plastic part of connector Protective tube Fiber core B Connector which already cut a Place connector locating pin into holder mid slot AD620 user manual AD INSTRUMENTS AD620 user manual 3 Pigtail Strip pigtail jacket by CFS 2 and retain 30mm wh Cut lines Ai TH Strip fiber coating by CFS 2 Stripper and retain 5mm Clean fiber Place the cleaned fiber to fiber holder XN Cut finished AD INSTRUMENTS Stripping diagram 30mm _ VAAN Patch cord jacket Pigtail jacket Fiber core 4 Bare Fiber Strip fiber by CFS 2 fiber stripper and retain 30mm E Clean the fiber Place fiber to fiber holder Place the fiber holder to AD 105H fiber cleaver for cut Cut finished Stripping diagram 30mm fo Coating Fiber core AD620 user manual AD INSTRUMENTS AD620 user manual Two Place fiber After fiber cutting continue the following operations Open wind protector uplift fiber presser
10. t offset is greater than this parameter PAUSE will be automatically started Even if PAUSE is in off position PAUSE If this item is open during the process of splicing and arc test the fiber will stop after pushed into screen PAUSE If this item is open during the process of splicing and arc test the fiber will stop after alignment Maintenance Set Lens check Check whether there is dust or saturation points in lens by this check result it can judge if the optical system of this machine suitable for splicing operation or not Motor resetting position the distance that motor left the initial position after switch on or resetting Day setup Set year month and day Clock setup set hour minute and second Parameter resume resume all parameters to default value AD INSTRUMENTS AD620 user manual Language Chinese or English Records check Arc times arc times of electrode including arc test splicing arc splicing again and manual splicing Arc times clear Recommend to do this operation after changing of electrode Heat times working time of heater Heat times clear recommend to do this operation after changing of heater Records view view the operation record of this machine including splicing time and splicing result If the splicing loss is 2 55 that means splicing failed Records clear clear all splicing records maximum records are 10000 0000 9999 Operation guide a lt Power On Off gt the bu
11. zzle will beep about second after this key is pressed down loose the key after the beep finished then the machine shut down A lt Reset gt the mahcine will be reset after this _ key is pressed down ew lt Heat gt Oven starts work after pressing down this key the heat led will keep working till heating finished or this key was pressed down again Pace It is a simple operation guide red by pressing page turning key 5 Switch on switch off and stand by Pressing switch will power on the machine In stand by pressing switch continuously machine will buzz when buzzing stopped still pressing the switch button the machine will power off once loosing the switch button Stand by AD INSTRUMENTS AD620 user manual 11 06 16 08 08 08 lt i Menu Power Start Heat Reset Stand by after power on and it will show the current day time and battery capacity and available operation button 6 Basic procedure of splicing One Prepare fiber 1 Drop Cable Place drop cable into stripper to 30mm position and strip drop cable coat by 30mm Strip fiber coating by CFS 2 Stripper and retain 3mm Clean fiber Place the cleaned drop cable to the drop cable holder Ue Please the holder to AD 105H Fiber Cleaver for cut AD INSTRUMENTS Cutting finished Stripping diagram 30mm 3mm Drop cable jacket Coating Fiber core 2 Splice on Connector A C
Download Pdf Manuals
Related Search