Home

installation

1. AIR HEALTH X FAN a a i a s FILTER xX e TURBO l l way F l a pit HOUR E ON OFF 15 MODE icon If MODE button is pressed current operation mode icon A AUTO COOL DRY FAN or zx HEAT only for heat pump models will show 16 LOCK icon m is displayed by pressing and buttons simultaneously Press them again to clear the display 17 LIGHT icon W is displayed by pressing the LIGHT button Press LIGHT button again to clear the display 18 SLEEP icon G is displayed by pressing the SLEEP button Press this button again to clear the display 19 TEMP icon Pressing TEMP button set temperature indoor ambient temperature outdoor ambient temperature and blank is displayed circularly OPERATIC i 20 Up amp down swing icon SI is displayed when pressing the up amp down swing button Press this button again to clear the display 21 Left amp right swing icon FR is displayed when pressing the left amp right swing button Press this button again to clear the display 22 SET TIME display After pressing TIMER button ON or OFF will blink This area will show the set time 23 DIGITAL display This area will show the set tempe rature In SAVE mode SE will be displayed During defrosting opera tion H1 will be displayed 24 FAN SPEED display Press FAN button to select the desired fan
2. 4 E a font Gas side A Tal i i piping insulation J Liquid side f piping insulation Mounting Board air proof with putty Waer Finally wrap it drai with tape ramage pipe ONIDA Discharge the air of the units It can used as vaccum pump Remove screw cap of closing valve and gas charging hole Open the closing valve gas closing with Allen wrench turn 90 clockwise valve then push the gas hole for about 10 seconds When a gas like fog appears it indicates that the air of unit has been discharged put back the screw cap of gas charging hole Liquid closing valve Liquid connecting pipe Cap Allen Wrench Gas connecting em Screw Cap Gas Do the leak test with leak detector or soap water Charging Screw Cap Hole Add refrigerant e fthe connecting pipe is longer than 7 meters add refrigerant as needed Add amount A Lm 7m 15g m A add refrigerant amount L the length of connecting pipe the length of connecting pipe m add amount g e Add refrigerant with the spring balance as specified above connecting pipe Indoor unit a ae PpS Outdoor unit Gas pipe R Gas charging hole Closing valve Bottle s valve of storage refrigerant Bottle of storage refrig rant Test e Proceed leak test with leak detector or soap water and inspect connecting cables before test operation Test procedure Control by emergency ope
3. TdT tT sO LIT T ae CITATA Eee TT Code ode moeni flea T PP PP tt PP PE Tt Product Details Please Tick The Appropriate Product Colour TV __ B amp W TV DVD Washing M C Jac _ Plasma TV Rear Projection TV Microwave Oven LCDTV Dealer s Name amp Address ModelNo J J ff Purchase Date Please Refer Sticker On Back Cover Of Your Product Day Month Year Signature Accept The Terms And Conditions of The Warranty Customer Signature Thank you for selecting a World Class product and we assure you that it will perform as per your expectations We thank you for taking your time to complete this form All Information Provided by You will be Kept Confidential Please Fill In Tear off Fold and Mail this form to Reach us within 10 days of the Product Purchase We welcome your Valuable Suggestions if any to Improve our Products and Services FOR OFFICE USE ONLY Customer Coa tt ttt td Branch PITT TET TTP tt tt tt Mirc Electronics Ltd Note Company Will Not Be Responsible For The Loss Of This Form During Transit For Other Details on Our Products amp Services Log On To www onida com BUSINESS REPLY ENVELOPE ONIDA CUSTOMER RELATION CENTRE Adonis Electronics Pvt Ltd Onida House I Mukund Ground Floor Mahal Industrial Estate off Mahakali Caves Road Andheri East Mumbai Mahara
4. speed setting AUTO Low Med High Your selection will be displayed in the LCD windows except the AUTO fan speed 1 ON OFF Press this button to turn on the unit Press this button again to turn off the unit 2 MODE Each time you press this button a mode is selected in a sequence that goes from AUTO COOL DRY FAN and HEAT as the following AUTO gt COOL gt DRY P FAN PHEAT to Note Only for models with heating function After energization AUTO mode is defaulted In AUTO mode the set temperature will not be displayed on the LCD and the unit will automatically select the suitable operation mode in accordance with the room temperature to make indoor room comfortable 3 00 es 3 Press this button to decrease set temperature Hold it down for above 2 seconds to rapidly decrease set temperature In AUTO mode set temperature is not adjustable 4 H Press this button to increase set temperature Hold it down for above 2 seconds to rapidly increase set temperature In AUTO mode set temperature is not adjustable 5 FAN This button is used for setting fan speed in the sequence that goes from AUTO am toatl then back to Auto E a Aacal a Oow speed M Medium speed Al High speed 6 gt Press3i button to start or stop up amp down swing function The remote controller defaults to simple swing condition e Press button and gt button at the same time at unit OFF to switch between simple
5. the Auto mode but the temperature and fan speed cannot be changed The operation was shown as below To open the panel the manual switch is on the displayer box Manual switch e Turn on the unit At unit turned off press the button the unit will run at Auto mode immediately The microcomputer will accord to the indoor temperature to select Cooling Heating Fan and obtain the comfortable effect e Turn off the unit At unit turned on press the button the unit will stop working AN e NOTICES FOR INSTALLATION GENERAL INSTA CTIONS FOR ION Safety Requirements For Electric Appliances 1 The power supply should be used the rated voltage and AC exclusive circuit the power cable diameter should be satisfied 2 Don t drag the power cable emphatically 3 It should be reliably earthed and it should be connected to the special earth device the installation work should be operated by the professional The air switch must have the functions of magnetic tripping and heat tripping in order to protect the short circuit and overloading 4 The min distance from the unit and combustive surface is 1 5m The appliance shall be installed in accordance with national wiring regulations 6 An all pole disconnection switch having a contact separation of at least 3mm in all poles should be connected in fixed wiring For models with a power plug make sure the plug is within
6. the SLEEP operation mode Press it again to cancel this function This function is available in COOL HEAT Only for models with heating function or DRY mode to maintain the most comfortable temperature for you 14 LIGHT Press LIGHT button to turn on the display s light and press this button again to turn off the display s light If the light is turned on X is displayed If the light is turned off g disappears 15 Combination of and buttons About lock Press and buttons simultaneously to lock or unlock the keypad If the remote controller is locked imal is displayed In this case pressing any button mm blinks three times 16 Combination2 of MODE and buttons About switch between Fahrenheit and Centigrade At unit OFF press MODE and buttons simultaneously to switch between C and F Displayer indicator light control of indoor unit Special selection button for those users who do not want light at night e Light on press light button when the light is off the indoor indicator light will be on e Light off press light button when the light is on the indoor indicator light will be off Notice when there s no display of indoor indicator please check the setting status for light function of wireless remote controller Emergency operation If the wireless remote control is lost or broken please use the manual switch button At this time the unit will run at
7. through the unit Please allow at least 2 meters free space onthe air outlet side and 0 3 meters on the air inlet side e lf more than one ODU is to be installed they must be properly separated so that the warm air from the outlet of one does not enter the inlet of the other e Avoid long and complicated routing between the IDU and ODU as shown in the three adjacent figures e oolong e Toohigh e Toomany bends e The ODU must be placed on strong frame or support If mounted on a wall please ensure that the wall is thick enough and that the frame is supported adequately e Finally it is most important for the ODU to be easily accessible to the service engineer It is advisable to discuss the same with the engineer before deciding upon the location of the unit If the ODU Is to be located on a high ledge adequate space must be provided for the service engineer to service the unit It is a good idea to provide a catwalk a platform around the unit and access door window to the Unit Electrical outlet After the location of the outdoor unit and indoor unit is finalised you must provide a suitable electrical outlet near the indoor unit i Bo p x Qu i oe EL MCB Tag be t STABILISER e INSTALLATIC KETCH CAUTION Ensure that the space around the left and right of the indoor unit is more than 12cm The indoor unit should be ins
8. Reinstall the battery cover plate Notes e When replacing the batteries do not use old or different batteries otherwise it may cause malfunction If the wireless remote controller will not be used for a long time please remove batteries to prevent damage from leaking batteries The operation should be performed in its receiving range It should be kept 1m away from the TV set or stereo sound sets If the wireless remote controller does not operate normally please take the batteries out and reinsert them after 30 seconds If it still can t operate properly replace the batteries VIEW FAN AUTO T aMi OPER AIR HEALTH X FAN HUMOTY ar ar S uaea TURD aw C T HOUR o ON OFF Cy e REMOTE OVE 1 ON OFF Press it to start or stop operation 2 MODE Press it to select operation mode AUTO COOL DRY FAN HEAT 3 6J 3 Press it to decrease temperature setting 4 6J 7J Press it to increase temperature setting 5 FAN Press it to set fan speed 6 3l Press it to set up amp down swing angle 7 HEALTH SAVE page 7 Press it to turn on or off health function 8 TA Press it to set left amp right swing angle 9 X FAN page 7 10 TEMP page 7 11 TIMER Press it to set timer ON timer OFF 12 TURBO page 8 13 SLEEP page 8 14 LIGHT Press it to turn on off the light FAN ER
9. act the dealer in following situations WN T WARRANTY TERMS AND CON IONS M S MIRC ELECTRONICS LTD WARRANTS THIS ONIDA AIR CONDITIONER except the front grill knobs remote unit and add on plastic parts TO THE ORIGINAL PURCHASER TO BE FREE FROM DEFECTS IN MATERIALS AND WORKMANSHIP WITHIN ONE YEAR FROM THE DATE OF PURCHASE AS PROVIDED IN THE WARRANTY REGISTERATION CARD WARRANTY FOR COMPRESSOR MIRC ELCTRONICS LTD HEREAFTER WARRANTS TO THE PURCHASER OF THIS ONIDA AIR CONDITIONER THAT FOR A PERIOD OF 12 MONTHS FROM THE DATE OF INVOICE WE WILL REPAIR REPLACE THE COMPRESSOR WHICH PROVES UPON INSPECTION BY US OR ANY OF OUR AUTHORISED SALES DEALERS TO HAVE BEEN DEFECTIVE DUE TO MANUFACTURING DEFECT This warranty is subject to terms and conditions as mentioned below iF This warranty shall be valid only for the said period of 12 months as specified above irrespective of whether the said unit has been in use or not for any reason whatsoever or the unit is moved from one location to another Warranty does not cover accessories external to the equipment The warranty period specified above shall include time taken for repairs replacements break downs transit time etc No notice of expiry period of warranty will be given by the company This warranty shall stand automatically terminated in the event of the said unit being serviced repaired installed de installed re installed or other
10. dition If it s damaged please contact ONIDA appointed maintenance center If there is rust on the outdoor unit please apply some paint to the rusty spot to avoid spreading BE CAREFUL when painting 5 Indoor and outdoor units can be wrapped by special protective bags to avoid rain and dust getting into the units to erode them N e PRECAUTIONS 0 BE TAKEN i Do s 4 Seal all air gaps inthe room Choose the right temperature to avoid over cooling Ventilate the room regularly Switch off the power supply if not in use for long Unplug the unit while cleaning Don t s X Don t leave the doors and windows open when the air conditioner is on Don t use hot water to clean your front grill Don t use Scouring powder harsh soaps wax or polish on the grill Don t switch on the air conditioner immediately after switching it off Wait for 2 minutes Don t operate with a clogged filter Don t block air intake amp outlet vents Don t change setting unnecessarily 3 3 INSTALLATION SATISFACTION e TROUBLE SHOOTING CHART e a Customer Name Phenomenon Troubleshooting A Address Indoor unit cannot deliver air e In HEAT mode when the temperature of indoor heat exchanger is very low that will stop deliver air in order to prevent cool air Within 2min e n HEAT mode when the outdoor temperature is low or high humidity there are much frost be formed on th
11. e outdoor heat exchanger that the unit will automatically defrost indoor unit stop plowing air for 3 12min During the a defrosting there is water flowing out or vapor be produced e In dehumidifying mode sometimes indoor MCB Rating E i Current Amps 1 fan will stop in order to avoid condensing Cable Size ee Ambient Temp C ee water be vapo rized again restrain aps O Moisture on air outlet vent e f unit is running under the high humidity for PASGT ee SnD Ae a long time the moisture will be condensed Input Voltage E Remote Operation S on the air outlet grill and drip off H1 Defrosting e Itis normal Customer s Response To be filled up by the Customer 1 Installation completed within 12hrs 24hrs 36hrs more than 36 hrs 2 How did you find the behavior of the Engineer Excellent Good Not satisfied 3 Overall rating of the service Excellent Good Not satisfied There is harsh sound during operation 4 Suggestion if any The terrible odors emitted during operation Water is leaking in the room Air switch or protection switch often breaks Carelessy splash water or gt Stop running and pull out of the plug Job Number Engineer s Signature Customer s Signature something into unit There is an abnormal heat in power supply cord and OS power plug Q f J N Immediately stop all operations and plug out cont
12. er can be washed by water but shall not be scrubbed with a brush or hard object When washing is completed dry the filter in shade rather than wipe with a rag Service Life for Healthy Filter The general service life for healthy filter is one year under normal operation As to silver ion filter it is ineffective when the surface turns black or green e This complementary instruction is only referred for the unit with healthy filter The graphs in this complementary instruction may be different from the actual product please refer to the actual product Please refer to the actual delivery for the quantity of healthy filter y EN TAKE CARE OF YOUR AIR CONDITIQNER Check before Use 1 Make sure that nothing obstructs the air inlet and air Outlet of indoor and outdoor units 2 Make sure there is effective grounding 3 Make sure the batteries for remote controller are replaced 4 Make sure the installation support for outdoor unit is in good condition If it s damaged please contact ONIDA appointed maintenance center If there is rust on the outdoor unit please apply some paint to the rusty spot to avoid spreading BE CAREFUL when painting Maintenance after Use 1 Disconnect the power for the air conditioner 2 Clean the filter and the body of indoor and outdoor units 3 Remove the dust and other objects on the outdoor unit 4 Make sure the installation support for outdoor unit is in good con
13. ference after reading it thoroughly Dear customer Congratulation on buying ONIDA Air Conditioner Your Air Conditioner comes with ONIDA Guarantee of Quality as detailed in the manual ONIDA takes great pride in providing its customers with state of the art products that adheres to international quality standards ONIDA is committed to following quality policy laid by our chairman and managing director Mr G L Mirchandani We are committed to quality and strive for continuous improvement through innovation and human development to give customer better value for money always ONIDA stands committed to provide the ultimate customer satisfaction as nothing brings us greater joy than having satisfied customers of ONIDA At ONIDA feedback and suggestions based on your product usage experience is greatly appreciated Please contact to us at response onida com G Sundar Chief Executive Officer The Onida Ethos Understanding customer ives dreams anq aspirations better than anyone else a es Salient Features Inside Overview Indoor Unit Display Remote Overview Operations Notices for installation General Instructions for Installation Installation Sketch Installation Take care of your Air Conditioner Precautions to be taken Trouble Shooting Chart Installation and Satisfaction Report Warranty Terms amp Conditions Preventive Maintenance Service Coupon Warra
14. for necessary verification and produce as and when required Warranty null and void if i The Air Conditioner is not purchased from the authorized dealers of the company li The Service Centre copy of warranty card is not received within 10days of date of purchase at the nearest Authorised Service Centre lil Any damage is caused by accident mishandling tampering with installation or negligence in following instructions of the user manual issued by Company iv Any damage is caused by improper electrical circuit outside the unit or by any defective electrical supply v At any time during the warranty period if any part of the unit is tampered with altered repaired or serviced by any unauthorized person not being the authorized representative of the company or its authorized dealers vi The serail number of the unit or any part thereof is damaged defaced altered obliterated or tampered with or removal for any reason whatsoever vill The unit is unauthorisedly moved from its original place of installation or re installation None of the employees and or Authorized Dealers of the Company have any authority whatsoever to vary the terms and conditions of this warranty This warranty shall be deemed to have been issued at Mumbai state of Maharashtra and courts at Mumbai shall have exclusive jurisdiction on matters covered by or following from this warranty and the original purchaser alone shall have cause of action arising ou
15. g j USER MANUAL Warranty Registration System Help us to serve you better by registering your product for Warranty Web Register at www onida com Telephone Call Centre No 0XX 39889000 0XX STD Code of State Capital Post Visit Post the Warranty Registration Card amp Service Centre Model INV18ELE7 Copy or Visit the Nearest Service Centre As per Government of India s E Waste Management and Handling Rules 2011 effective from May 1st 2012 the product purchased by you is to be considered as E Waste and cannot be disposed off with your general household waste It should be disposed of through the company s collection center so as to prevent any damage to environment Collection Center address Mirc Electronics Ltd Village Kudus Bhiwandi Wada road Taluka Wada Dist Thane 421312 Tel no 952525 220375 377 Visit at www onida com for details about collection Centers We request you to make a note of the above details and support us in our endeavour to ensure an environmental friendly nation ONIDA MIRC Electronics Ltd Onida House G 1 MIDC Mahakali Caves Road Andheri East Mumbai 400 093 a nit may vary The Onida Ethos Putting customers at the center of our existence IMPORTANT e Please read this owner s manual carefully and thoroughly before installing and operating your room air conditioners e Please retain this owner s manual for future re
16. h as oil Stain please clean it with the mixture of warm water lt 45 C and neutral abluent and then dry it up in the shade Note Never use water above 45 C to clean the air filter as it may cause deformation or discoloration Reinstall the air filter Install the air filter along arrow 1 direction and then buckle the panel cover along arrow 2 Installation and Maintenance for Healthy filter 1 Press the clasp as shown by arrow 1 to loosen the clasps at the lower end until a sound of crack is heard press the clasp as shown by arrow 2 to open the clasps at the upper end open the panel and then pull the filter downward to remove it As shown in fig a 2 Install the healthy filter on the air filter as shown in fig b If the healthy filter fails to be installed on the air filter please install the healthy filter on the front case As shown in fig c 3 Install the air filter along arrow 1 direction and then buckle the panel cover along arrow 2 As shown in fig d Clean and Maintenance for Healthy Filter Please remove the healthy filter before cleaning and reinstall it well after cleaning according to the installation instruction Please note that the silver ion filter shall NOT be washed by water Active carbon filter photocatalytic filter LTC catalyst and formaldehyde killer filt
17. igure e Do not locate the unit directly opposite a door which is opened frequently The cold air will go out of the room each time the door is opened as shown in the adjacent figure e All indoor units will form condensate water Please ensure that the condensate can bedrainedoutofthe room to a toilet pantry etc The installation engineer will make sure that a U bend is provided in the drain to prevent insects from coming into the room through the drain tube as shown inthe adjacent figure L GENERAL INS PRUCTIONS FOR INSTAL GENERAL I IN N S R UCTIONS FOR NEY NION Locating the Outdoor Unit The outdoor unit houses the compressor condenser fan and electrical components ON ROOF The heat removed from the room is expelled to the atmosphere through the outdoor unit ON SLESHADE Once again the Onida dealer s Technician will ensure optimal installation of the ODU for you However the following information will be of interest to you OM WALL WITH FRAME i lah SKIK HNE Y e The Outdoor Unit can be mounted on a wall sunshade or skirting IDU ABOVE ODU g d ODL amp IDU IN SAME LEVEL i MAX DISTANCE 12 MTS ssi pal MAX HEIGHT 5 MIS 4 Y i MAS HEIGHT 5 MTS e ideally the ODU should not be too far away from the IDU the recommended distances are eer marked in the adjacent figure MOL ABOVE IDL e Ensure that air can pass freely
18. ive expression of BLOW for the purpose of under standing 10 TEMP Press this button could select displaying the indoor setting temperature or indoor ambient temperature When the indoor unit firstly power on it will display the setting temperature if the temperature s displaying status is changed from other status to A displays the ambient temperature 5s later or within 5s it receives other remote control signal that will return to display the setting temperature if the users haven t set up the temperature displaying status that will display the setting temperature 11 TIMER Press TIMER button at unit ON to set TIMER OFF HOUR OFF blinks Press TIMER button at unit OFF to set TIMER ON HOUR ON blinks In this case pressing or button changes time setting Holding down either button rapidly changes time setting time setting range 0 5 24hours Press TIMER button again to confirm setting HOUR ON OFF stops blinking If there is not any operation of button within 5 seconds during HOUR ON OFF blinking TIMER setting will be cancelled 12 TURBO Press this button to activate deactivate the Turbo function which enables the unit to reach the preset temperature in shortest time In COOL mode the unit will blow strong cooling air at super high fan speed In HEAT mode the unit will blow strong heating air at super high fan speed This function is not applicable for some models 13 SLEEP Press this button to go into
19. nty Card Customer Copy Warranty Card service Center Copy Ba The Onida Ethos Delivering products that enrich customer lifestyle relably stylishly and thoughtfully Model Code INV18ELE7 Aesthetics a Unique Elegant Model with High EER lb Sleek Indoor Unit Performance a Imported High BTU Tropicalised Compressor b Trapezoidal Inner Grooved Tube c Large L Shaped Condenser Coil d High RPM Fan Motor with High Static Features a Clean Air b Multi Step Air Swing for Customized Cooling C Surround Air d Turbo Safety amp Reliability a Hydrophilic Fins b Full Function LCD Remote c Special Insulation on the Air Vent d 5 Stage Epoxy Polyester Painting a aN INSIDE OVERVIEW l va o m INDOOR UNIT Return warm Air in Front panel q Conditioned Air out mi sis t Remote controller E m OUTDOOR UNIT _ Connection pipe and connecting wire Exhaust Air DISPLAY oj x o INDOOR UNF Display on the indoor unit For the icon of LED windows only relevant icons will light up with their displays on DRY x e REMOTE OV Replacement of Batteries 1 Remove the battery cover plate from the rear of the remote controller As shown in the figure 2 Take out the old batteries 3 Insert two new AAA1 5V dry batteries and pay attention to the polarity 4
20. ration switch or remote controller For detailed operation see OPERATION OF AIR CONDITIONER inthe manual ONIDA JN Caution Disconnect the power supply before cleaning and maintenance Do not splash water on the units for cleaning as electric shocks may occur Wipe the units with a dry soft cloth or a cloth slightly moistened with water or cleaner not with volatile liquid such as thinner or gasoline Cleaning the Front Panel Remove the front panel Dip a piece of cloth into the water colder than 45 C and dry it Then wipe the dirty part of front panel Note Do not immerse the front panel into water so as to protect microprocessor components and circuit diagram on the front panel Cleaning the Air Filter every 3 months Note If the air conditioner operates under dusty environment the frequency of cleaning air filter shall increase correspondingly When the filter is removed do not touch the fins of the indoor unit with fingers for fear of scalding Take down the air filter Press the clasp as shown by arrow 1 to loosen the lower end of clasps until a sound of crack is heard press the clasp as shown by arrow 2 to open the Upper end of clasp open the panel and then pull the filter downward to remove it As shown in figa and b Fig b Clean the air filter Clean the filter with a vacuum cleaner or wash the filter with water If the filter is very dirty Suc
21. re i to wa Left rear side refrigerant pipe hole 665 l Pigi rear side atrigerant pipe hole 65 u Drill on the wall Confirm the position of holes and drill holes of diameter 65 mm on the wall 180mm Center of Hole O65mm Align Ruler with straight line Connecting of cables j 1 Open the front panel ere 2 Dismantle the electric box cover ae aCe 1 and fastener e 5 3 Connectthe cable L I 2 4 Reassemble the fastener and electric box AD a Yellow green cover BI Per SN eer Power connection wire E Installation of indoor unit After putting the pipe assembly through the wall attach the indoor unit to the mounting plate on the wall as shown in the figure E Installation of outdoor unit e Theconnecting cables must be clipped together e Special cable to be used to connect indoor unit and outdoor unit e The electric box cover must be mounted on its position on outdoor unit m Connecting of pipes Pipe Diameter of pipe Torque N m Sealing the wall hole and clamping the pipe e Use putty to seal the wall hole External connection e Use pipe fastener to clamp the pipe on wall electric wire Liquid side piping B pede oe i Mounting Board me
22. reach after installation OJ Air conditioner Btu h Air switch capacity 18 24K 25A 4q Earthing requirements 1 Air conditioner is type electric appliance thus please do conduct reliable earthing measure 2 The yellow green two color wire in air conditioner is earthing wire and cannot be used for other propose It cannot be cut off and be fix it by screw otherwise it would cause electric shock The earth resistance should accord to the National Criterion 4 The user power must offer the reliable earthing terminal Please don t connect the earthing wire with the following place A Tap water pipe B Gas pipe C Contamination pipe D Other places that professional personnel consider them unreliable ee 5 Including an air switch with suitable capacity please note the following table Air switch PCB board should be included magnet buckle and heating buckle function it can protect the circuit short and overload Caution please do not use the fuse only for protect ONIDA Locating the indoor and outdoor units properly will help optimise the performance of your airconditioner While your Onida Dealer s Technician will be happy to guide you on the best location for your airconditioner here are afew helpful hints Locating the Indoor Unit e Locate the IDU for the best cool air circulation Preferably there should be no obstructions nearby as shown in the adjacent f
23. s prior to the said change On receipt of such information the authorized dealer or any of its counterparts shall arrange for de installation of the said unit on chargeable basis However in the event of any damage occuring to the unit or to any of its parts during the course of its transit by the said purchaser repair or replacement the said unit or any part thereof damaged shall not be covered by this warranty ONIDA 10 11 12 13 14 It shall be the absolute discretion of the company to a effect the repairs or replacement of parts whether at the site of installation or at any service centre and b have the job attended to either by the Company s service personnel or its authorised dealer This warranty is in the nature of and for the purpose of set forth herein above and in particular the Company shall not in any event be liable for direct indirect incidental or consequential loss or damages to either the said purchaser and or his property or any other third party The AC is designed to operate at a range 230V 10 Any failure due to operation of the machine beyond these limits will not be covered by the above warranty Customer shall ensure that a stabilizer is installed in those areas where voltage is not available within the warranty range 230V 10 The stabilizer should be of any reputed manufacturer tested and recommended by the Company The purchaser should preserve the original invoice
24. shtra India 400093
25. swing and static swing blinks for 2 seconds e In static swing condition pressing button the swing angle of up amp down louver changes as Y SI gt 1 1 l A oFF lt Ul e If the unit is turned off during swing operation the louver will stop at present position 7 HEALTH SAVE Press HEALTH part of this button to turn on or off HEALTH function Pressing SAVE part of this button SE is displayed and the unit goes into SAVE operation mode Press SAVE part of the button again to cancel SAVE function During SAVE operation the temperature and fan speed is not adjustable 8 e Press 7A button to start or stop left amp right swing function The remote controller defaults to simple swing condition e Press button and button at the same time at unit OFF to switch between simple swing and static swing blinks for 2 seconds e In static swing condition pressing button the swing angle of left amp right louver changes as below me gt es ee OO 1 OFF AN N e If the unit is turned off during swing operation the louver will stop at present position 9 X FAN Pressing X FAN button in COOL or DRY mode the icon X FAN is displayed and the indoor fan will continue operation for 10 minutes in order to dry the indoor unit even though you have turned off the unit After energization X FAN OFF is defaulted X FAN is not available in AUTO FAN and HEAT mode Note X FAN is the alternat
26. t Colour TV __ B amp W TV DVD Washing M C Jac _ Plasma TV Rear Projection TV Microwave Oven LCDTV Dealer s Name amp Address Model No seialNo Please Refer Sticker On Back Cover Of Your Product Purchase Date Day Month Year Signature Accept The Terms And Conditions of The Warranty Customer Signature Thank you for selecting a World Class product and we assure you that it will perform as per your expectations We thank you for taking your time to complete this form All Information Provided by You will be Kept Confidential Please Fill In Tear off Fold and Mail this form fo Reach us within 10 days of fhe Product Purchase We welcome your Valuable Suggestions if any to Improve our Products and Services FOR OFFICE USE ONLY Customer Coa ttt td Branch PTT TET Tt ttt tt tt Mirc Electronics Ltd Note Company Will Not Be Responsible For The Loss Of This Form During Transit For Other Details on Our Products amp Services Log On To www onida com MIRC Electronics Limited sanar No Warranty Card Service Centre Copy Customer Details Title Mr Ms Mrs s Name Residence Address LT TT TEE PPT ttt ete tt EEE EE EET ost PE TT dT PE TUT PUT TUT TE PP em EET EE TT state TT tT tt tt occupations dP dP dE
27. t of the transaction Customer Identification Number gt Sr No Unit Model Name of Serviceman Date Time Sign of Serviceman Customer Identification Number Unit Model Sr No Name of Serviceman Date Time Sign of Serviceman Preventive Maintenance Service Preventive Maintenance Service 1 Customer Identification Number Name of the customer 3 Installation address Phone Mobile E mail Unit model Service report number Customer s Signature Preventive Maintenance Service Preventive Maintenance Service 2 Customer Identification Number Name of the customer Installation address Phone Mobile E mail Unit model Service report number Customer s Signature Date Fax Serial Number Name msi Se Date Fax Serial Number Name memes i SC MIRC Electronics Limited Serial No Warranty Card Customer Copy Customer Details Title Mr Ms Mrs s Name Residence Address PTT TTT PEP Pt ttt et et Pt te PPE EE EET os TP TdT UPL TU TUT LEU EU TUT TE PP deme EET EE TT state _ TT tt tt occupations dP dP dP dE ET tT oe ee gt AEE Eee eee Code ode mobile No flew PtP PP te tt PP ET Tt i ii dC Product Details Please Tick The Appropriate Produc
28. talled allowing a minimum clearance of 15cm from the ceiling Usea stud finder to locate studs to prevent unnecessary damage to the wall A minimum pipe run of 3 metres is required to minimise vibration amp excessive noise e The indoor unit should be installed on the wall at a height of 1 7 metres or more from the floor but less than 2 3 from he floor e Directions A B and C should be free from obstructions Installation Plate Clip Anchor Self tapping Screw A ST3 9X25 Seal Drain Joint ooo _ Liquid Side 6 35 12000Btu h A Gas Side 12 7 12000Btu h Assembly Liquid Side 9 53 18000Btu h Gas Side 16 0 18000Btu h Remote Controller Self tapping Screw B ST3 9X10 Remote Controller Holder Note Except the above parts provided the other parts needed during installation you must purchase 60cm above S 2 gt CERRUCEEEEEG GE ECEBERULEREUEauEECEmE Remote Controller Mounting screw B ST2 9x10 C H AP Remote controller holder Additional drain pipe Wrapping tape KA Q Loop the connective m INDOOR UNIT 1 Fitment of mounting plate The mounting plate should be fitted on the structural part of wall on which indoor unit is to be installed 2 Drilltwo holes at a distance of 450 mm between them for the expansion bolts T 150mm or more to ceiling Installation plate Indoor unit outline i 120mm or mo
29. wise attended to by any person or organization or agency or by the said purchaser himself other than the authorized representative of the company Parts of the unit replaced or repaired under the terms of this warranty are warranted only for the remaining period of the original warranty period For attending any service call under this warranty beyond the municipal limits of the locality in which the authorized representative dealer is situated outstation locations all to and fro travelling and other incidental expenses as prevailing from time to time incurred in connection with the visit of the service personnel technicians etc shall be borne by the said purchaser and shall be payable in advance Additionally all expenses incurred by the authorized representative dealer in collecting the said unit or any part thereof from such outstation locations and its return to the original location shall be borne by the said purchaser Any loss of refrigerant caused due to sabotage improper handling or treatment carelessness accident fire flood earthquake or any natural calamity any corrosive action on the original refrigerant pipes fittings valves etc for whatever reasons shall not be covered under this warranty In the event of any change in the location of the unit during the warranty period this warranty shall become null and void unless the fact of the proposed change is communicated in writing to the authorized dealer at least seven 7 day

installation

Contents

Download Pdf Manuals

Related Search

Related Contents