adaptat on nstruct ons SM6-36
Contents
1. boulevard Franklin Roosevelt F 92500 Rueil Malmaison France Tel 33 0 1 41 29 85 00 http www schneider electric com S1B22864 revision 01 As standards specifications and designs change from time to time please ask for confirmation of the information given in this publication Conception r daction Service Documentation Technique T amp D Edition 28 06 20112. ON A CAUTION All the operations described below Only undertake the work after must be performed in compliance having read and understood with applicable safety standards all the explanations given in this under the responsibility document If you have any difficulty of a competent authority complying with these rules please contact Schneider Electric A WARNING The contractor must be certified and authorised to manipulate and perform work on the SM6 unit 4 S1B22864 revision 01 concerning this document safety requirements special tools contents of kit n 9015427 Al preparation field of application S1B22864 revision 01 general This publication is intended strictly for use within Schneider Electric and is not a sales document It contains instructions concerning the modification or the adaptation of assemblies The parts referred to form part of a kit and are not available separately This document may not be reproduced in any form or by any means and is reserved exclusively for use by Schneider Electric representatives The cubicle compartment in which the contact jaws are to be changed must be de energised 1 torque wrench 0 1 to 1 Nm 1 contact jaw 1 plate 1 bag of nuts and bolts The procedures for accessing the downstream earthing switch and reassembling the cubicle are described in the corresponding user Manual No restrictions situation of subsets to f
3. SM6 36 English distribution HTA adaptation Instructions changing the downstream earthing switch contact jaws Schneider SCHNEIDER ELECTRIC foreword symbols and Caution conventions you will find all the symbols below throughout the document indicating the hazard levels depending on the different types of situation A DINNE as per iso 3864 2 DANGER failure to follow this instruction will result in death or serious injury as per iso 3864 2 gt 2 a WARNING failure to follow this instruction may result_in death or serious Injury A CAUTION as per iso 3864 2 CAUTION failure to follow this instruction may result in injuries This alert signal can also be used to indicate practices that could damage the SM6 unit INFORMATION ADVICE We draw your attention to this specific point S1B22864 revision 01 contact the Schneider Electric service unit for diagnosis and advice D Call your sales representative who will put you in contact with the closest centre You can log on to www schneider electric com SCHNEIDER ELECTRIC group service distribution rules A CAUTION The aim of this publication is to enable the SM6 unit to be installed correctly A CAUTION This document is not a commercial document It is a strictly technical document drawn up by Schneider Electric S1B22864 revision 01 safety rules S1B22864 revision 01 A CAUTI
4. it in the cubicle yO Access to the subsets remove the front panel see instructions for use 6 S1B22864 revision 01 procedure Bes Le A L152 grease they TOPAS should feel greasy when touched Fit but do not tighten the nuts and Lubricate the contact points G with Nuts A bolts B plates C and bolts contact jaws D ISOFLEX ap J ag E U E D D T 9 T Q gt w Cc O O are A O aS Oo v Cc c 5 a m U v 5 8 o U C 2 Ow Par D L 2 oo EP z D A O CU F w PS Pe ge I gE mM 6 So Fo s 202g TC v fon O U Z Q N Us 0 YZ u 2c Og ars Cs N n Cc Z lt lt O u Oys T lt Bae oO S oO C VU UV52 S1B22864 revision 01 N Looking down from above the assembly centre the jaws with respect to the deflectors Tighten the nuts and bolts ATTENTION CAUTION Maximum tightening torque 0 38 Nm LY S1B22864 revision 01 Schneider Electric service centers are there for engineering and technical assistance Start up training preventive and corrective maintenance adaptation work Spare parts Call your sales representative who will put you in touch with your nearest Schneider Electric service centre Schneider Electric Industries SAS 89
Download Pdf Manuals
Related Search