installation and user instructions for as3 & as4 vertical travel
Contents
1. IS384 ECN3345 Page 7 SECTION 7 GENERAL FAULT FINDING Element will not heat up Is the unit connected to the mains and the unit switched on Plug or connect the unit and switch on Check mains isolator or fuse Reset isolator or replace fuse Consult service engineer SECTION 8 GUARANTEE All Silverlink equipment is fully guaranteed for parts and labour for a period of twelve month The guarantee does not cover 1 Accidental breakage or damage 2 Operational misuse wear and tear from normal usage incorrect adjustment or neglect 3 Incorrect installation maintenance modification or unauthorised service work SECTION 9 ACCESSORIES The following accessories are available for your Lincat salamander grill Accessory Part number Wall Mounting Brackets AS3 BR41 Wall Mounting Brackets AS4 BR51 IS384 ECN3345 Page 82. Single phase 13A plug 5 Way terminal block Power rating 240V kW 2 8 4 5 300 MIN 640 WALL MOUNTED 550 Check list of enclosures Fig 1 Please ensure that the following items are included with this piece of equipment Model AS3 AS4 Tick Drip Crumb Tray 1 Wire Tray Wire Support Rack Heat Shield User Instructions Guarantee card elf Rep ai 18384 ECN3345 Page 3 SECTION 2 INSTALLATION 2 1 PREPARATION 2 1 2 3 4 1 Remove all packaging materials and protective coatings from both the outer body and the drip crumb tray prior to installation 2 Remove transportation screws from rear panel of unit see fig 2 3 Do not use handle to carry unit 2 SITING The appliance must be installed on a non combustible level surface in a suitable position that is well lit and positioned so as to prevent accidental touching Partitions walls kitchen furniture and other materials less than 100 mm from the appliance should be made from non combustible material Ensure there is a free flow of air and adequate ventilation around the appliance and that no vents are blocked Silverlink Vertical Travel Salamanders can be either installed on a counter or wall mounted using wall mounting brackets see section 9 optional accessories INSTALLING A WALL MOUNTED UNIT o ee Gh o Refer to dimensional dra
3. Lincat SILVERLINK GOO INSTALLATION AND USER INSTRUCTIONS FOR AS3 amp AS4 VERTICAL TRAVEL SALAMANDER GRILLS 1S384 ECN3345 Page 1 Please read the following carefully before using this appliance Warnings and Precautions Please ensure that all commissioning checks and initial start up procedures have taken place This manual should be kept in a safe and accessible place for future reference This appliance is designed for professional use and must only be operated by qualified personnel It is mandatory that all appliances with a power rating over 3kW are installed commissioned and serviced by a qualified and competent person as defined by the regulations in force in the country of installation Failure to comply will invalidate the warranty Please ensure that the appliance is serviced regularly by a competent catering equipment engineer WARNING Disconnect the unit from the electricity supply before servicing or undertaking any electrical maintenance Parts of this unit may become hot in normal use therefore suitable precautions must be taken to avoid accidental contact 18384 ECN3345 Page 2 SECTION 1 Introduction Technical Data Model number AS3 AS4 Overall height mm 500 500 Width mm inc handles 600 600 Depth mm inc handles 550 550 Weight Kg 45 47 5 Electricity supply requirements Single phase 12 2 Amps Single phase 18 8 Amps Electricity supply connection
4. hood to highest position Switch on Salamander on off switch will illuminate Warm up time is 10 15 minutes Place plates or dishes on grill tray Adjust height of hood to desired position for food Raise hood to maximum height before removing any plates or dishes Ensure sliding grill tray is always fully pushed back after use The audible timer does not control the power Unit must be switched off at on off switch SAA WN a 1S384 ECN3345 Page 5 Warning e This appliance should not be operated with hood in lowest position for longer than 30 minutes Make sure that food does not come into contact with heating elements to prevent soiling or damage SECTION 4 CLEANING Warning Disconnect the unit from the power supply before carrying out any cleaning operations HEAT SHEILD WIRE TRAY SUPPORT WIRE TRAY RUNNER DRIP CRUMB TRAY Fig 3 1 Lift out wire tray grid and drip crumb tray 2 Slide out wire tray support 3 Loosen knurled knobs and lift off heat shield over knobs After use clean the unit using a warm detergent solution Do not use abrasives Do not use any products containing chlorine to clean stainless steel surfaces Do not clean the appliance using a water jet In extreme conditions a branded cleaner such as Carbon off may be used 18384 ECN3345 Page 6 REASSEMBLY AFTER CLEANING 1 Slide wire tray support back over wire tray runners 2 Place drip crumb tray into wire
5. tray support taking care that the stops on the drip crumb tray are positioned beyond the front uprights of the wire tray runners SECTION 5 SERVICE AND MAINTAINANCE Catering equipment should be routinely serviced to ensure a long and trouble free life With this in mind it is recommended that appliances are serviced every six months by a competent engineer For help regarding the installation maintenance and use of your Lincat equipment please call LINCAT GROUP SERVICE HELP DESK 01522 875520 Please quote both the model and serial numbers from the data plate attached to the unit and give brief details of the service requirement Lincat reserve the right to carry out any work under warranty during normal working hours i e Monday to Friday 8 30 a m 5 30 p m AUTHORISED SERVICE AGENTS We recommend that all servicing other than routine cleaning be carried out by our authorised service agents and will accept no responsibility for work carried out by other persons SECTION 6 SPARES LIST AS3 AS4 Part number Part numbers Part description EL50 EL237 Heating Element KN95 KN95 Timer Control Knob KN163 KN163 Knurled Knob PL201 Cable amp Plug TE45 Terminal Block Connector CO214 Contactor RO35 RO35 Nylon Roller SW69 SW69 On Off Switch SS05 SSO05 Counterbalance Strap WI16 WI16 Wire Tray Runner WIl7 WIl7 Wire Tray Support WIL8 WILS Wire Tray Grid DR62 DR62 Drip Crumb Tray
6. wing fig 1 and drawing of mounting holes see fig 2 Use wall mounting kit supplied by Lincat optional extra Loosen 4 screws in back of unit Fit brackets x 2 to back of unit using existing screws Drill 4 holes in wall according to drawing below Secure unit to wall LOOSEN SCREWS 4 OFF IN BACK OF UNIT 300 FIT BRACKETS 2 OFF ONTO 4 SCREWS TRANSPORTATION SCREWS 2 OFF TO BE REMOVED Mounting hole centres to be used when unit is wall mounted 1384 ECN3345 Page 4 2 3 ELECTRICAL SUPPLY AND CONNECTION Ensure that isolation sockets are free from obstruction and are easily accessible Model AS3 is fitted with a 3 pin plug for connection to a standard switched socket Model AS4 must be connected to the electricity supply by a qualified electrician Ensure that the supply is adequate for the unit to be installed The appliance should be connected to the mains via a suitable isolating switch having at least 3mm contact separation in all poles 2 4 CONTROL PANEL TIMER KNOB ON OFF NEON SWITCH 2 5 PREPARATION FOR USE 1 Ensure element hood moves freely and remains at set height when released 2 6 USER INSTRUCTION Ensure that the person responsible understands how to safely operate clean and switch off this unit and is made aware of the position of the isolating switch Note This manual must be kept in a safe and accessible place for future reference SECTION 3 OPERATION Raise element
Download Pdf Manuals
Related Search