A9GT-50STAND User`s Manual
Contents
1. case it is important to strictly observe the directions indicated with the above signs Keep this manual in a place which allows you to easily reach it whenever necessary Please make sure that the end user of this equipment be provided with this manual PRECAUTIONS FOR INSTALLATION lt DANGER Make sure to shut off all the phases of the system power supply externally before installing a power supply module wiring or working on the GOT There may be a hazard of electric shock or damage to the GOT unless all the phases of the system power supply are shut off Make sure to apply the terminal cover to the GOT if the power is to be supplied to the GOT after completing wiring work on the GOT s power supply terminal There may be a hazard of electric shock unless the cover is installed ZA CAUTION Use the GOT in an environment which satisfies the general specifications described in the GOT User s Manual Using in an environment other than that satisfies the general specifications could cause an electric shock a fire or damage or deterioration to the GOT Be extremely cautious so that your finger etc will not be caught when adjusting the installing angle after removing the angle adjusting screw from the stand To install the stand to the GOT fix it securely with the clamp Then tighten the mounting screws securely by applying a specified torque in the range of 36 to 48Nem 3 7 to 4 9kgfem 3 2 to 4 2lbeinch cou2. MITSUBISHI A9GT 50STAND User s Manual Thank you for purchasing the MELSEC GOT Series To ensure correct use of this equipment please carefully read this manual prior to use A9GT 50STAND U Type 1DM111 IB NA 0800021 B 0406 MEE Mitsubishi Graphics Operation Terminal Manuals Relevant Manual For relevant manuals refer to the PDF manual stored within the drawing software 1999 MITSUBISHI ELECTRIC CORPORATION SAFETY PRECAUTIONS Read these precautions prior to use When using Mitsubishi equipment thoroughly read this manual and the associated manuals that are introduced in this manual Also pay careful attention to safety and handle the module properly These precautions apply only to Mitsubishi equipment Please refer to the relevant users manuals for safety precautions pertaining to Mitsubishi programmable controller systems and Graphics Operation Terminal abbreviated as GOT hereafter The SAFETY PRECAUTIONS in this manual are classified into two categories DANGER and CAUTION i Procedures which may lead to a dangerous condition DANGER and cause death or serious personal injury if not i observed as directed i Procedures which may lead to a dangerous condition A CAUTION and cause minor to medium personal injury or i damage only to property if not observed as directed Depending on circumstances procedures indicated with CAUTION could also lead to serious results In any
3. Ratingen Tel 886 2 2299 2499 GERMANY Korea HAN NEUNG TECHNO CO LTD Tel 49 2102 486 0 1F Dong Seo Game Channel Bldg U K Mitsubishi Electric Europe B V UK 660 11 Deungchon dong Kangsec ku Branch Seoul Korea Travellers Lane Hatfield Herts AL10 Tel 82 2 3660 9552 8XB UK Singapore Mitsubishi Electric Asia Pte Ltd Tel 44 1707 276100 307 ALEXANDRA ROAD 05 01 02 Italy Mitsubishi Electric Europe B V Italian MITSUBISHI ELECTRIC BUILDING Branch SINGAPORE 159943 Centro Dir Colleoni Pal Perseo Ingr 2 Tel 65 6473 2308 Via Paracelso 12 20041 Agrate B Thailand F A Tech Co Ltd oi e Milano Italy 898 28 29 30 S V City Building Office Tel 39 039 6053344 Tower 2 Floor 17 18 Rama 3 Road Spain Mitsubishi Electric Europe B V Spanish Bangkpongpang Yannawa Branch Bangkok 10120 Carretera de Rubi 76 80 Tel 66 2 682 6522 08190 Sant Cugat del Valles Indonesia P T Autoteknindo SUMBER MAKMUR Barcelona Spain Jl Muara Karang Selatan Block A Utara No 1 Kav No 11 Kawasan Industri Pergudangan Jakarta Utara 14440 Tel 62 21 663 0833 India Messung Systems Put Ltd Electronic Sadan NO 111 Unit No15 M I D C BHOSARI PUNE 411026 Tel 91 20 712 2807 Tel 34 93 565 3131 France Mitsubishi Electric Europe B V French Branch 25 Boulevard des Bouvets F 92741 Nanterre Cedex France TEL 33 1 5568 5568 South Africa Circuit Breaker Industries LTD Australia Mitsubishi Electric Australia Pty Ltd Tri
4. ixing the GOT at a position which allows an easy view of the GOT s monitor screen when debugging screen data which is displayed on the GOT as illustrated below This stand is dedicated for common use with A950GOT A951GOT A953GOT and A956GOT 2 HOW TO USE THE STAND 1 Determine the angle for installing the GOT Slide the angle adjustment fitting as shown below to determine the angle The angle can be adjusted to 75 65 55 or 45 g gt 2 Once the angle is determined insert the angle adjustment fitting s fixing hook into the hook insertion section on the bottom of the stand 3 Securely tighten the fixing screw e mA 4 Insert the GOT from the front of Stand and install it to Stand Refer to the A950GOT A951GOT A953GOT A956GOT User s Manual for details on installing the installation fitting 5 After the installation perform wiring etc 3 OUTSIDE DIMENSIONS For 75 angle A az g lex 8 D gt JE g D 2 o o y o y 156 6 14 262 gt 10 31 220 8 66 Unit mm inch Weight _kg lb 1 1 2 4 Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi machine damage or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to prod
5. ld cause dropping of the GOT Make sure that the installing angle of the GOT is 45 55 65 or 75 degrees when adjusting it with the stand kept installed to the GOT The stand would touch and give damage to the GOT if the adjusting angle is not within the range as specified PRECAUTIONS FOR WIRING ZA CAUTION Perform wiring on the GOT appropriately after ensuring its rated voltage and terminal configuration Using the power supply of a different rating or the wiring error could cause a fire or a malfunction To avoid electric shocks make sure to ground FG terminal applying Type D Grounding Type 3 Grounding Tighten the power supply terminal screws to the specified torque of 36 to 48Nem 3 7 to 4 9kgf m 3 2 to 4 2lbeinch Loose terminal screws could cause shortcircuit If overtightened on the other hand terminal screws would break or damage the GOT thereby causing shortcircuit Make sure that foreign materials such as chips or waste wires are not caught inside of the GOT because they could cause failures To remove the communications cable or power cable connected to the GOT never hold and pull the cable itself Make sure to use a hand to hold the part that is closest and connected to the GOT Pulling the cable itself with the GOT kept connected could damage the GOT or cable thereby causing failures 1 OVERVIEW This manual explains the A9GT 50STAND Referred to as Stand hereafter Stand is used for f
6. pswitch Drive Elandsfontein Gauteng 348 Victoria Road PostalBag No 2 South Africa Rydalmere N S W 2116 Australia Tel 27 11 928 2000 Tel 61 2 9684 7777 MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE 1 8 12 OFFICE TOWER Z 14F HARUMI CHUO KU 104 6212 JAPAN NAGOYA WORKS 1 14 YADA MINAMI 5 CHOME HIGASHI KU NAGOYA JAPAN When exported from Japan this manual does not require al of Economy Trade and Industry for service transaction permission Specifications subject to change without notice Printed in Japan on recycled paper
7. ucts other than Mitsubishi products and to other duties A For safe use e This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life e Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi e This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the product fails install appropriate backup or failsafe functions in the system Country Region Sales office Tel Country Region Sales office Tel U S A Mitsubishi Electric Automation Inc Hong Kong Ryoden Automation Ltd 500 Corporate Woods Parkway Vernon 10th Floor Manulife Tower 169 Electric Hills IL 60061 Road North Point HongKong Tel 1 847 478 2100 Tel 852 2887 8870 Brazil MELCO TEC Rep Com e Assessoria China Ryoden Automation Shanghai Ltd Tecnica Ltda 3F Block5 Building Automation AV Paulista 1471 Conj 308 Instrumentation Plaza 103 Cao Bao Rd Sao Paulo City Sao Paulo State Shanghai 200233 China Brazil Tel 86 21 6475 3228 Tel 55 11 283 2423 Taiwan Setsuyo Enterprise Co Ltd Germany Mitsubishi Electric Europe B V German 6F No 105 Wu Kung 3rd RD Wu Ku Branch Hsiang Taipei Hsine Taiwan Gothaer Strasse 8 D 40880
Download Pdf Manuals
Related Search