Operation and Service Manual
Contents
1. Specifications This section lists the complete 16194A specifications These specifications are the performance standards and limits against which the 16194A is tested When shipped from the factory the 16194A meets the following specifications Maximum DC Bias Voltage sssssssssssssss I ee 40V Operating Temperature sssssssssssss sss n 55 to 200 C Operating Humidity wet bulb temperature lt 40 C AN 15 to 95 RH Non operating Temperature sssssssssssss s ee ee ee ee 55 to 200 C Non operating Humidity wet bulb temperature lt 65 C IEEE Up to 90 RH AGIT eee e ee eee eee hee 350 g Dimension se sss e 150 W x 40 H x 80 D mm 1 2 General Information Supplemental Performance Characteristics This section lists supplemental performance characteristics Supplemental performance characteristics are not specifications but are typical characteristics included as additional information for the operator Supplemental performance characteristics are not guaranteed Frequency Range With OPEN SHORT and electrical length compensation 4 DC to 500 MHz With OPEN SHORT LOAD compensation ccciccci cece cece eens DC to 2 GHz Electrical length s iiissssssssssse RR e 50 0 mm Additional Error 20 x f With OPEN SHORT and electrical length compensation Repeatability Surface mount device In2. Description Agilent Part Quantity Number D Test fixture 16194A 1 Operation and Service Manual P N 16194 90030 1 Shorting device 1x1x2 4 mm P N 16191 29001 1 1 6x2 4x2 mm P N 16191 29002 1 2 4x2 4x3 2 mm P N 16191 29003 1 2 4x2 4x4 5 mm P N 16191 29004 1 Case for Shorting Device P N 1540 0692 1 50 Q Chip Resistor P N 0699 2829 10 Tweezers P N 8710 2081 1 D Wrench P N 8710 1181 1 1 Operation and Service Manual is not shown in Figure 2 1 2 Contained if you ordered the 16194A option 701 2 2 Preparation for Use Exchanging the device holder The 16194A can hold both leaded devices and surface mount devices by exchanging the device holder The exchanging procedure is as follows Remove the ground plate 2 When measuring a surface mount device attach the knob on the device holder as shown in Figure 2 2 9 Select the device holder suitable for the device type Loosen its knob and insert it into the arm 4 Set the ground plate Device Holder for SMD for leaded device Ground Plate O EA aas 16194A rie O Was 16194A ACO02002 Figure 2 2 Exchanging the Device Holder Preparation for Use 2 3 Repackaging the Test Fixture for Shipment If shipment to an Agilent Technologies service center is requir
3. 2 2 2 2 5 2 8 3 1 Connecting the 16194A to the Measurement Terminal 3 2 3 2 Placing the Device EE EE 3 3 3 3 Setting Open Condition EE ZEE 3 4 4 1 Replaceable Parts for Main Assembly MV 4 2 4 2 Replaceable Parts around the Holder Aim Assembly MN 4 3 4 8 Replaceable Parts for Test Stage MEL 4 4 4 4 View Around the Electrode MM 4 5 Tables 1 1 Furnished Accessories TN 1 2 2 1 16194A Contents ll ll ns 2 2 4 1 Replaceable Parts for Main Assembly EE N VV 4 2 4 2 Replaceable Parts around the Holder Aim Assembly ML 4 3 4 3 Replaceable Parts for Test Stage MEL 4 4 4 4 Required Equipment EE EE 4 6 4 5 Short and Open Impedance Value Guideline 4 6 Contents 2 General Information Introduction The purpose of this manual is to enable you to use your 16194A High Temperature Component Fixture efficiently and confidently Manual Summary This manual contains the following m The specification of the 16194A m Installing the 16194A m Operating the 16194A m Ordering replaceable parts for the 16194A Product Description The 16194A is used to measure both axial radial leaded devices and surface mount devices within the temperature range of 55 C to 200 C Applicable Instruments The 16194A has been designed specifically for the measurements within the temperature range o
4. surface mount device and leaded device measurements use the 50 Q chip resistor as a LOAD device The reference value for LOAD compensation is R 50 0 L 0 H 5 Perform OPEN compensation 6 Measure the device under test Note In case of using the 4291B with option 013 014 High Temperature Test Head i the recommended error compensation is as follows TA 9 When using option 018 ee ee ee ee ee OPEN SHORT LOAD When using option 014 below 500MHz OPEN SHORT Fixture Select When using option 014 over 500MHz OPEN SHORT LOAD Operation 3 1 Warning The 161944 has the capability for 55 C to 200 C temperature A measurement in environmental testing Use gloves to prevent burns when handling heated parts Connecting the Test Fixture for Use 1 Calibrate your analyzer at the APC 7 connector plane before connecting the test fixture 2 Place the fixture on the APC 7 connector 3 Tighten turn counterclockwise the coupling nut of the APC 7 connector ACS03001 Figure 3 1 Connecting the 16194A to the Measurement Terminal 3 2 Operation Placing Shorting Device Load Device or Device Under Test 1 Adjust the position of the groun
5. voltage terminals fed from the interior by voltage exceeding 1000 volts must be so marked Protective conductor terminal For protection against electrical shock in case of a fault Used with wiring terminals to indicate the terminal which must be connected to ground before operating equipment Low noise or noiseless clean ground earth terminal Used for a signal common as well as providing protection against electrical shock in case of fault A terminal marked with this symbol must be connected to ground in the manner described in the installation Operation manual and before operating the equipment Frame or chassis terminal A connection to the frame chassis of the equipment which normally includes all exposed metal structures Alternating current power line Direct current power line Alternating or direct current power line Warning denotes a hazard It calls attention to a procedure practice condition or the like which if not correctly performed or adhered to could result in injury or death to personnel Caution sign denotes a hazard It calls attention to a procedure practice condition or the like which if not correctly performed or adhered to could result damage to or destruction of part or all of the product Note denotes important information It calls attention to a procedure practice condition or the like which is essential to highlight vii APC 79 is a U S registered trademark of the Bunke
6. 6194 60002 1 Device Holder for SMD 4 16194 60001 1 Device Holder for Leaded Device 1 The parts in the Holder for Leaded Device cannot be replaced separately 4 2 Service ac504002 Figure 4 2 Replaceable Parts around the Holder Aim Assembly Table 4 2 Replaceable Parts around the Holder Aim Assembly Reference Agilent Part Designator Number Qty Description 1 16194 01201 1 Arm 2 3050 1139 2 Washer Teflon 3 16194 25008 1 Spacer 4 16191 24010 1 Pin 5 1460 2380 1 Spring 6 3050 0891 1 Washer 7 0515 1550 1 Screw Pan Head M3 L8 8 16194 00201 1 Fixture Chassis 9 16194 24008 1 Housing 10 0515 1052 1 Screw Hex 11 0515 0914 2 Screw Flat Head M3 L6 12 16194 24009 1 Latch 13 16194 25004 1 Screw Service 4 3 ACS04003 Figure 4 3 Replaceable Parts for Test Stage Table 4 3 Replaceable Parts for Test Stage Reference Agilent Part Designator Number Qty Description 1 16194 24002 1 Electrode 2 3050 1139 1 Washer Teflon 3 0515 2421 1 Screw Pan Head M1 4 4 0515 0914 7 Screw Flat Head M3 5 16194 20001 1 Test Stage 6 16453 24011 1 Flange 7 not assigned 1 Center Conductor Assembly 8 16194 20002 1 Ground Plate 9 16194 24005 1 Knob A 1250 0816 1 Contact of the APC 7 Center Pin B 16453 60001 1 Bead Assembly C 16194 25001 1 Insulator D 16194 24001 1 Contact of the Electrode 4 4 Service Replacement Procedure This section covers the disassemb
7. Agilent 16194A High Temperature Component Fixture Operation and Service Manual RE Agilent Technologies Agilent Part No 16194 90030 Printed in JAPAN May 2003 Fifth Edition Notice The information contained in this document is subject to change without notice This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be photocopied reproduced or translated to another language without the prior written consent of the Agilent Technologies Agilent Technologies Japan Ltd Component Test PGU Kobe 1 3 2 Murotani Nishi ku Kobe shi Hyogo 651 2241 Japan Copyright Agilent Technologies Japan Ltd 1994 1998 1999 2000 2003 Manual Printing History The manual printing date and part number indicate its current edition The printing date changes when a new edition is printed Minor corrections and updates that are incorporated at reprint do not cause the date to change The manual part number changes when extensive technical changes are incorporated March 1994 ssssssssssssssss es First Edition part number 16194 90000 May 1998 Se ee ee ees Second Edition part number 16194 90010 December 1999 EE eee Third Edition part number 16194 90010 September 2000 oaaae eaaa anana ee ee ee ee Fourth Edition part number 16194 90020 May 2003 2 0 0 EG Ge n Fifth Edition part number 16194 90030 Safety Summary The foll
8. d plate and tighten its knob 2 Adjust the position of the device holder so that it presses against the device When measuring a leaded device adjust the distance between the two pins to the device size Then tighten the knob of the device holder 3 Move the arm outward 4 Place the device on the electrodes and press it with the device holder Figure 3 2 b d When placing a leaded device put its leads on the notch of the 16194A s electrodes You can adjust the pressure of the arm by turning the pressure adjustment using the wrench Flectrode Shorting device evice a Adjust the ground plate and move the arm Shorting device LOAD device c Leaded device d Leaded device DUT measurement SHORT LOAD compensation AC503002 Figure 3 2 Placing the Device Operation 3 3 Setting the Open Condition 1 If there is any device on the electrodes remove it 2 When measuring a surface mount device move the arm outward and latch it Then make the distance between the electrodes same as the device size by adjusting the ground plate Figure 3 3 a 3 When measuring a leaded device make the distance between the electrodes and the distance between the device holder s pins same as t
9. ductive device 0 cn nee nen e e 0 2 2 5 x f Q Capacitive device EE Ee Ge SG se e hee 80 250 x f uS Leaded device Inductive device sssssssssssssssssssssssss seen 0 4 12 5 x f 9 Capacitive device ee ee e e es 80 500 x f uS Option 701 shorting device size P N 16191 29001 2 0 00 e eme e e 1x1 x2 4 mm P N 16191 29002 ssssssssssssse e ene 1 6 x 2 4 x 2 mm P N 16191 29008 sssssssssssssss e e e een 2 4 x 2 4 x 3 2 mm P N 16191 29004 nananana aaaeeeaa aranne m een 2 4 x 2 4 x 4 5 mm Option 010 shorting device size P N 16191 28005 sssssssssssssse s e ee 0 5 x 0 5 x 1 mm P N 16191 29006 sssssssssssssss Ie e een 0 8 x 0 8 x 1 6 mm P N 16191 29007 EE IH e eee 0 8 x 1 2 x 2 mm P N 16191 29008 sssssssssssssss e en 0 8 x 1 6 x 3 2 mm DC resistance of supplied chip resistor sse esses 500 0 1 96 f frequency GHz H A A H d 2mm lt L lt 15mm L lt 15mm 8mm lt L lt 21mm H lt 5mm H lt 4 5mm 0 2mm lt d 0 2mm lt d ACS01001 Figure 1 1 Applicable Device Size General Information 1 3 Supplied Shorting Device Inductance P N 16191 29001 1 1 mm oe ee Se Ge Ge IIIA 0 2 nH 1 P N 16191 29002 1 2 mm i e SG Ge SS Ge Se ee een 0 2 nH 1 P N 16191 29002 1 1 6 mm 0 2 nH 1 P N 16191 29002 1 2 4 mm oe GE SG Ge Ge e ee ee ee ee 0 7 nH 2 P N 16191 29008 1 3 2 mm oe Ee de Se SG Ge Ge ttt
10. e instrument or software or firmware will be uninterrupted or error free Limitation Of Warranty The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance by Buyer Buyer supplied software or interfacing unauthorized modification or misuse operation outside of the environmental specifications for the product or improper site preparation or maintenance No other warranty is expressed or implied Agilent Technologies specifically disclaims the implied warranties of merchantability and fitness for a particular purpose Exclusive Remedies The remedies provided herein are buyer s sole and exclusive remedies Agilent Technologies shall not be liable for any direct indirect special incidental or consequential damages whether based on contract tort or any other legal theory Assistance Product maintenance agreements and other customer assistance agreements are available for Agilent Technologies products For any assistance contact your nearest Agilent Technologies Sales and Service Office Addresses are provided at the back of this manual vi Safety Symbols General definitions of safety symbols used on equipment or in manuals Warning Caution i Note i Instruction manual symbol the product is marked with this symbol when it is necessary for the user to refer to the instruction manual in order to protect against damage to the instrument Indicates dangerous
11. ed each test fixture should be repackaged using the original factory packaging materials If this material is not available comparable packaging materials may be used Wrap the 16194A in heavy paper and pack in anti static plastic packing material Use sufficient shock absorbing material on all sides of the 16194A to provide a thick firm cushion and to prevent movement Seal the shipping container securely and mark it FRAGILE 2 4 Preparation for Use Operation Introduction This chapter describes how to perform error compensation and how to measure the device with the 16194A The topics include the following m Operating flow m Connecting the test fixture for use m Placing shorting device load device or device under test m Setting the open condition Operating Flow The following shows typical operating procedure Before performing a measurement it is necessary to compensate for the residual error of the fixture The error compensation functions are different for each instrument For procedure on how to perform each error compensation see the Operation Manual supplied with your analyzer 1 Perform calibration at the measurement terminal of your analyzer and connect the 161944 2 Perform electrical length compensation Fixture Select Port Extension 9 Perform SHORT compensation For both surface mount device and leaded device measurements use the shorting device 4 Perform LOAD compensation if necessary For both
12. ee ee ee ee 0 6 nH 2 P N 16191 29004 1 4 5 mm oe de SE Ed Ge Ge Ge t teen nen 0 6 nH 2 1 4 General Information Preparation for Use Introduction This chapter explains how to install the 16194A The topics include the following m Initial inspection m Exchanging the device holder m Repackaging the test fixture for shipment Initial Inspection The 16194A has been carefully inspected before being shipped from the factory It should be in perfect physical condition no scratches dents or the like It should also be in perfect electrical condition Verify this by carefully performing an incoming inspection to check the 16194A set for signs of physical damage and missing contents If any discrepancy is found notify the carrier and Agilent Technologies Your Agilent Technologies sales office will arrange for repair and replacement without waiting for the claim to be settled m Inspect the shipping container for damage Keep the shipping materials until the inspection is completed m Verify that the shipping container contains everything shown in Figure 2 1 and listed in Table 2 1 m Inspect the exterior of the 16194A for any signs of damage Preparation for Use 2 1 O UA Sano 16194A a oS ACS02001 Figure 2 1 16194A Product Overview Table 2 1 16194A Contents
13. ervice and repair to ensure the safety features are maintained Dangerous Procedure Warnings Warnings such as the example below precede potentially dangerous procedures throughout this manual Instructions contained in the warnings must be followed Warning Dangerous voltages capable of causing death are present in this A instrument Use extreme caution when handling testing and adjusting this instrument The voltage levels found in this test fixture when used with the intended instruments do not warrant more than normal safety precautions for operator safety Operating Precaution Do not exceed the operating input power voltage and current level and signal type appropriate for the instrument being used refer to your instrument s operation manual Caution Electrostatic discharge EspD can damage the highly sensitive microcircuits in your instrument ESD damage is most likely to occur as the test fixtures are i being connected or disconnected Protect them from ESD damage by wearing a grounding strap that provides a high resistance path to ground Alternatively ground yourself to discharge any static charge built up by touching the outer shell of any grounded instrument chassis before touching the test port connectors Never touch the test clip contacts Use a work station equipped with an anti static work surface Certification Agilent Technologies certifies that this product met its published specif
14. est amp Measurement European Marketing Organization P O Box 999 1180 AZ Amstelveen The Netherlands tel 31 20 547 9999 Japan Agilent Technologies Japan Ltd Call Center 9 1 Takakura Cho Hachioji Shi Tokyo 192 8510 Japan tel 81 426 56 7832 fax 81 426 56 7840 Latin America Agilent Technologies Latin American Region Headquarters 5200 Blue Lagoon Drive Suite 4950 Miami Florida 33126 U S A tel 305 267 4245 fax 305 267 4286 Australia New Zealand Agilent Technologies Australia Pty Ltd 347 Burwood Highway Forest Hill Victoria 3131 tel 1 800 629 485 Australia
15. f 55 C to 200 C using the 4291B with High Temperature Test Head Option013 014 The 161944 is also compatible with the following instruments in normal temperature measurements The operating temperature depends on the specification of each instrument 4191A 4195A with 41951A 4194A with 41941A B and 16099A Terminal Adapter A Terminal Pair type LCR Meters Impedance Analyzers with 16085B Terminal Adapter General Information 1 1 Options Available The following option is supplied for the 16194A Option 010 Add industry standard size short bar set Option 701 Short bars set 1x1x2 4 1 6x2 4x2 3 2x2 4x2 4 4 5x2 4x2 4 mm Accessories Supplied The following accessories are supplied with the 16194A Table 1 1 Furnished Accessories Description Part Number Quantity Operation and Service Manual P N 16194 90030 1 Option 701 P N 16191 29001 1 P N 16191 29002 1 P N 16191 29008 1 P N 16191 29004 1 Case for Shorting Device P N 1540 0692 1 Option 010 P N 16191 29005 1 P N 16191 29006 1 P N 16191 29007 1 P N 16191 29008 1 50 Q Chip Resistor P N 0699 2829 10 Tweezers P N 8710 2081 1 Wrench P N 8710 1181 1 Option 010 sizes are the same as industry standard EIA EIAJ SMD sizes This short bar set has the following SMD sizes included 1005 mm 0402 inch 1608 mm 0603 inch 2012 mm 0805 inch 3216 mm 1206 inch Order option 010 if the SMD that is to be measured has the same size as the EIA EIAJ sizes
16. he device size Then press the electrodes with the device holder s pins not latching the arm Figure 3 3 b Electrode a do b Leaded device Figure 3 3 Setting Open Condition 3 4 Operation Service Introduction This chapter covers the following subjects m Assembly Replacement Replaceable Parts o Replacement Procedure m Troubleshooting Warning This service information is for use by qualified personnel only Do NOT A perform any service function other than that contained in the operating section unless you are qualified to do so Caution When you repair the 16194A put on lint free gloves to prevrent contaminating inner parts of the 16194A Agilent Technologies supplies lint free gloves i Agilent part number 9300 0163 Assembly Replacement Replaceable Parts Table 4 1 through Table 4 3 show and list the replaceable parts for the 16194A The parts listed can be ordered from your nearest Agilent Technologies Office Ordering information must include the Agilent part number and the quantity required Service 4 1 ac504001 Figure 4 1 Replaceable Parts for Main Assembly Table 4 1 Replaceable Parts for Main Assembly Reference Agilent Part Designator Number Qty Description 1 not assigned 1 Main Assembly 2 16194 24007 1 Knob 3 1
17. ications at the time of shipment from the factory Agilent Technologies further certifies that its calibration measurements are traceable to the United States National Institute of Standards and Technology to the extent allowed by the Institution s calibration facility or to the calibration facilities of other International Standards Organization members Warranty This Agilent Technologies instrument product is warranted against defects in material and workmanship for a period of one year from the date of shipment except that in the case of certain components listed in Instrument Specifications of this manual the warranty shall be for the specified period During the warranty period Agilent Technologies will at its option either repair or replace products which prove to be defective For warranty service or repair this product must be returned to a service facility designated by Agilent Technologies Buyer shall prepay shipping charges to Agilent Technologies and Agilent Technologies shall pay shipping charges to return the product to Buyer However Buyer shall pay all shipping charges duties and taxes for products returned to Agilent Technologies from another country Agilent Technologies warrants that its software and firmware designated by Agilent Technologies for use with an instrument will execute its programming instruction when property installed on that instrument Agilent Technologies does not warrant that the operation of th
18. ling and assembling procedure of the center conductor assembly See Table 4 3 for the reference designators Disassembling Procedure 1 Remove the center conductor assembly 7 from the test stage 6 2 Clamp the contact of the APC 7 using pliers which have rubber covered noses 3 Loosen the contact D Assembling Procedure 1 Put thread sealant to the screw part of the contact of the APC 7 2 Assemble the parts amp and D 3 Set the angle of the contact assembly 7 as shown in Figure 4 4 1 Contact to a Agilent Technologies offece for the part number of the thread sealant Recommended t Recommended ACS04005 Figure 4 4 View Around the Electrode Service 4 5 Troubleshooting This section includes the procedure used to troubleshoot the 16194A Table 4 4 Required Equipment Equipment Recommended Model Substitute Model Impedance Analyzer 4291B 4396B with 43961A Short and Open Impedance Check 1 2 3 Jo OU Ha 8 Put the 2 4x2 4x3 2 mm Shorting Device Agilent PN 16194 29003 between the electrodes Place the fixture on the calibrated APC 7 terminal of the Impedance Analyzer Set the Impedance Analyzer as follows Measurement Parameter Ls series inductance Start Frequency 10 MHz Stop Frequency 100 MHz OSC Level 0 12 V Number of Point 2 Point Averaging Fact
19. or 16 Point Averaging ON Perform a single sweep measurement Read Ls value at 10 MHz and 100 MHz Keeping the electrode distance remove the shorting device from the 16194A Set the Impedance Analyzer as follows Measurement Parameter Cp parallel capacitance Read Cp value at 10 MHz and 100 MHz The guideline for the short and open impedance value is as follows 4 6 Table 4 5 Short and Open Impedance Value Guideline Parameter Frequency Guideline absolute value Short Ls 10 MHz and 100 MHz 7 nH 4 nH Open Cp 10 MHz and 100 MHz 2 4 pF 0 5 pF Service REGIONAL SALES AND SUPPORT OFFICES For more information about Agilent Technologies test and measurement products applications services and for a current sales office listing visit our web site http www agilent com find tmdir You can also contact one of the following centers and ask for a test and measurement sales representative 11 29 99 United States fax 61 3 9272 0749 Agilent Technologies tel 0 800 738 378 New Zealand Test and Measurement Call Center fax 64 4 802 6881 P O Box 4026 Englewood CO 80155 4026 Asia Pacific tel 1 800 452 4844 Agilent Technologies 24 F Cityplaza One 1111 King s Road Canada Taikoo Shing Hong Kong Agilent Technologies Canada Inc tel 852 3197 7777 5150 Spectrum Way fax 852 2506 9284 Mississauga Ontario L4W 5GI tel 1 877 894 4414 Europe Agilent Technologies T
20. owing general safety precautions must be observed during all phases of operation service and repair of this instrument Failure to comply with these precautions or with specific WARNINGS given elsewhere in this manual violates safety standards of design manufacture and intended use of the instrument The Agilent Technologies assumes no liability for the customer s failure to comply with these requirements DO NOT Operate In An Explosive Atmosphere Do not operate the instrument in the presence of flammable gasses or fumes Operation of any electrical instrument in such an environment constitutes a safety hazard Keep Away From Live Circuits Operating personnel must not remove instrument covers Component replacement and internal adjustments must be made by qualified maintenance personnel Do not replace components with the power cable connected Under certain conditions dangerous voltages may exist even with the power cable removed To avoid injuries always disconnect power and discharge circuits before touching them DO NOT Service Or Adjust Alone Do not attempt internal service or adjustment unless another person capable of rendering first aid and resuscitation is present DO NOT Substitute Parts Or Modify Instrument Because of the danger of introducing additional hazards do not substitute parts or perform unauthorized modifications to the instrument Return the instrument to a Agilent Technologies Sales and Service Office for s
21. r Ramo Corporation viii Contents General Information Introduction ManualSummary Product Description Applicable Instruments el Options Available Accessories Supplied SS A Specifications SS Supplemental Performance Characteristics Preparation for Use Introduction Initial Inspection 2 Exchanging the device holder Repackaging the Test Fixture for Shipment Operation Introduction Operating Flow Connecting the Test Fixture for Use Placing Shorting Device Load Device or Device Under Test Setting the Open Condition Service Introduction 022 Assembly Replacement ww 2 2 ll SS SS SS SS ss Replaceable Parts a a ll s ll ss Replacement Procedure 2 2 2 2 2 2 2 252 2 52 2 Disassembling Procedure 5 ll sn Assembling Procedure 2 2 2 2 2 2 2 2 2 2 2 2 2 Troubleshooting a ll ll SS SS SS SS SS SS ss Short and Open Impedance Check 4 len Hi LA Sd hd Hi Hd hd Mk 1 w yyy e eS 4 1 4 1 4 1 4 5 4 5 4 5 4 6 4 6 Contents 1 Figures 1 1 Applicable Device Size lll ll lh 1 3 2 1 16194A Product Overview SS SS SS SS SS SS Se 2 2 2 2 Exchanging the Device Holder 2 2
Download Pdf Manuals
Related Search