SEAT BELTS - Textfiles.com
Contents
1. prepared to brace themselves in the event the retractor does not lock Apply brakes firmly and make a very hard stop During stop seat belts should lock and not be extended If the seat belt retractor assembly does not lock per form the retractor off vehicle check SEAT BELT RETRACTOR OFF VEHICLE CHECK 1 Remove the seat belt retractor assembly 2 Slowly pull out belt while tilting the retractor assembly forward from the mounted position without twisting the retractor assembly as shown in the illustration Revision July 2007 SB 11 2005 Armada SEAT BELTS Front seat belt 15 degress or 35 degress or less tilt more tilt Mounted position Tilt the seat belt retractor forward from the mounted position without twisting the retractor 15 degrees or less tilt Belt can be pulled out 35 degrees or more tilt Belt locks and cannot be pulled out If NG replace the retractor assembly Revision July 2007 Rear seat belt Outer seat belt Mounted position Center seat belt Mounted position SB 12 15 degress or less tilt 15 degress or 35 degress or more tilt 35 degress or more tilt PHIA0257E 2005 Armada LATCH LOWER ANCHORS AND TETHER FOR CHILDREN SYSTEM LATCH LOWER ANCHORS AND TETHER FOR CHILDREN SYSTEM PFP 75466 Removal and Installation EN NOTE The LATCH Lower Anchors and Tether for Children system is not serviceable Revision July 2007 SB 13 2005 Armada TOP TETHER STRAP2. CHILD RESTRAINT TOP TETHER STRAP CHILD RESTRAINT PFP 88000 Removal and Installation 1 Remove luggage room rear lower finisher Refer to El 37 LUG GAGE FLOOR TRIM 49 0 N m 5 0 kg m 36 0 ft Ib 2 Remove bolt and remove tether anchor from the luggage box bracket Installation is in the reverse order of removal EHSO0028W WHIA0135E Revision July 2007 SB 14 2005 Armada
3. H RESTRAINTS SECTION S B SEAT BELTS CONTENTS 2 2 TOA ROW Precautions for Supplemental Restraint System REMOVAL AND INSTALLATION _ SRS AIR BAG and SEAT BELT PRE TEN Third Row Center ccccceccecccecceeceeeeeeeaneeeeeneeeneeeees ele eg 2 REMOVAL AND INSTALLATION Precautions for Seat Belt Service 2 Seat Belt Inspection EE 2 Aan Aere BR Le EE 3 PRELIMINARY Removal Installation of Front Seat Belt 3 SEAT BELT RETRACTOR ON VEHICLE FRONT SEAT BELT RETRACTOR 4 A te e FRONT SEAT BELT 5 SEAT BELT RETRACTOR OFF VEHICLE Removal and Installation of Rear Seat Belt 6 11 REMOVALS 7 LATCH LOWER ANCHORS AND TETHER FOR INSTALLATION ooo cece eeceeeceeceeceeeceeceeeeeeaeeeeeeneees 7 CHILDREN SYSTEM 13 SECOND ROW SEAT BELT BUCKLE 7 Removal and Installation 13 SECOND ROW SEAT BELT RETRACTOR TOP TETHER STRAP CHILD RESTRAINT 14 BEING BE E RRE 7 Removal and Installation 14 Revision
4. July 2007 SB 1 2005 Armada PRECAUTIONS PRECAUTIONS 00001 Precautions for Supplemental Restraint System SRS AIR BAG SEAT BELT PRE TENSIONER EHS00280 The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE TENSIONER used along with a front seat belt helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision This system includes seat belt switch inputs and dual stage front air bag modules The SRS system uses the seat belt switches to determine the front air bag deployment and may only deploy one front air bag depending on the severity of a collision and whether the front occupants are belted or unbelted Information necessary to service the system safely is included in the SRS and SB section of this Service Man ual WARNING avoid rendering the SRS inoperative which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation all maintenance must be per formed by an authorized NISSAN INFINITI dealer e Improper maintenance including incorrect removal and installation of the SRS can lead to per sonal injury caused by unintentional activation of the system For removal of Spiral Cable and Air Bag Module see the SRS section not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual SRS wiring harnesse
5. a SEAT BELTS FRONT SEAT BELT RETRACTOR Removal CAUTION e Before servicing SRS turn the ignition switch off disconnect both battery cables and wait at least 3 minutes 1 Remove the center pillar upper lower finishers Refer to El 32 BODY SIDE TRIM 2 Remove the seat belt retractor anchor bolts and seat belt retractor and belt assembly On RH side disconnect the seat belt tension sensor 5 0 0 5 44 0 7 49 0 5 0 36 0 OJ 49 0 5 0 36 0 N m in Ib O N m kg m pm LHIA0047E 3 Disconnect the seat belt pre tensioner electrical connector CAUTION e For installing removing seat belt pre tensioner connector insert a thin screwdriver wrapped in tape into the notch lift Screwdriver the lock and remove the connector Install the connector with the lock raised and push the lock into the connector t PHIA0341E Installation Installation is in the reverse order of removal e Install the seat belt retractor and belt assembly upper bolt first Ensure that seat belt height adjuster is locked in the lowest position during installation Revision July 2007 SB 4 2005 Armada SEAT BELTS FRONT SEAT BELT BUCKLE Removal 1 Remove the front seat Refer to SE 89 FRONT SEAT 2 Remove the seat cushion Refer to SE 94 SEAT CUSHION TRIM AND PAD DRIVER SEAT CUSHION ASSEMBLY PASSENGER 3 Disconnect the seat belt buckle pre tensioner electrical co
6. belt pre tensioner should be replaced even if the seat belts are not in use during a frontal collision in which the air bags are deployed Replace any seat belt assembly including anchor bolts if e The seat belt was in use at the time of a collision except for minor collisions and the belts retractors and buckles show no damage and continue to operate properly seat belt was damaged in an accident e torn webbing bent retractor or guide etc The seat belt attaching point was damaged an accident Inspect the seat belt attaching area for damage or distortion and repair as necessary before installing a new seat belt assembly Anchor bolts are deformed or worn out e The seat belt pre tensioner should be replaced even if the seat belts are not in use during the collision in which the air bags are deployed Revision July 2007 SB 2 2005 Armada SEAT BELTS SEAT BELTS 86884 Removal Installation of Front Seat Belt SS O N m kg m 1 O N m ft Ib leese O 49 5 0 36 LHIAOO66E 1 Assist handle 2 Assist handle screw cover 3 D ring anchor bolt cover 4 Seat belt buckle 5 Seatbelt retractor and belt assem 6 Anchor cover bly LH 7 Seat belt pre tensioner connector 8 Center pillar lower finisher 9 Seat belt anchor 10 Center pillar 11 Center pillar upper finisher 12 Seat belt height adjuster 13 Seat belt height adjuster finisher Revision July 2007 SB 3 2005 Armad
7. fer to El 32 BODY SIDE TRIM Remove the seat belt guide bolt Remove seat belt retractor anchor bolt and the seat belt assembly Remove the seat belt height adjustor assembly INSTALLATION Installation is in the reverse order of removal Ensure that seat belt height adjuster is locked in the lowest position during installation SECOND ROW SEAT BELT BUCKLE Removal 1 Remove the rear bucket seat 2 Remove the screw and seat cushion inner finisher Refer to SE 96 Second Row Center 3 Remove the anchor bolt and buckle 4 Remove the rear bench seat Refer to SE 96 Second Row Outboard 5 Remove the seat cushion finisher 6 Remove the anchor bolt and buckle Installation Installation is in the reverse order of removal SECOND ROW SEAT BELT RETRACTOR BENCH SEAT Removal a Remove seat belt anchor Remove seat belt bezel Remove seat back upholstery and foam Refer to SE 96 REAR SEAT Remove seat belt retractor cover Remove bolt and remove seat belt retractor and seat belt assembly Installation Installation is in the reverse order of removal Revision July 2007 SB 7 2005 Armada SEAT BELTS Third Row geet REMOVAL AND INSTALLATION Third Row Outboard SY 77 0 36 O 49 5 0 36 49 5 0 36 O 49 5 0 36 O N m kg m nm WHIA0133E 1 D ring mounting bracket 2 Seatbelt retractor and belt assem Retractor mounting bracke
8. ies in use during a collision be replaced unless the col lision was minor and the belts show no damage and continue to operate properly Failure to do so could result in serious personal injury in an accident Seat belt assemblies not in use during a colli sion should also be replaced if either damage or improper operation is noted Seat belt pre tensioners should be replaced even if the seat belts are not in use during a frontal collision in which the air bags are deployed Replace any seat belt assembly including anchor bolts if e The seat belt was in use at the time of a collision except for minor collisions and the belts retractors and buckles show no damage and continue to operate properly e The seat belt was damaged in an accident i e torn webbing bent retractor or guide seat belt attaching point was damaged an accident Inspect the seat belt attaching area for damage or distortion and repair as necessary before installing a new seat belt assembly e Anchor bolts are deformed or worn out The seat belt pre tensioner should be replaced even if the seat belts are not in use during the collision in which the air bags are deployed PRELIMINARY CHECKS 1 Check the seat belt warning lamp chime for proper operation as follows a Switch ignition ON The seat belt warning lamp should illuminate Also the seat belt warning chime should sound for about seven seconds b Fasten drivers seat belt The seat belt warn
9. ing lamp should go out and the chime if sounding should stop 2 If the air bag warning lamp is blinking conduct self diagnosis using CONSULT II and air bag warning lamp Refer to SRS 20 SRS Operation Check 3 Check that the seat belt retractor seat belt anchor and buckle bolts are securely attached 4 Check the shoulder seat belt guide and shoulder belt height adjuster for front seats Ensure guide swivels freely and that belt lays flat and does not bind in guide Ensure height adjuster operates properly and holds securely 5 Check retractor operation a Fully extend the seat belt webbing and check for twists tears or other damage b Allow the seat belt to retract Ensure that belt returns smoothly and completely into the retractor If the seat belt does not return smoothly wipe the inside of the loops with a clean paper cloth because dirt built up in the loops of the upper anchors can cause the seat belts to retract slowly c Fasten the seat belt Check the seat belt returns smoothly and completely to the retractor If the belt does not return smoothly the cause may be an accumulation of dust or dirt Use the SEAT BELT TAPE SET and perform the following steps Inspect the front seat belt through anchor 1 Pull the seat belt out to a length of 500 mm 19 69 in or more 2 Use a clip or other device to hold the seat belt at the center pillar belt opening 3 Pass a thin wire through the through anchor belt opening H
10. mine if a retractor assembly is operating prop erly ELR Function Stationary Check Grasp the shoulder belt and pull forward quickly The retractor should lock and prevent the belt from extending further ALR Function Stationary Check 1 Pull out entire length of seat belt from retractor until a click is heard 2 Retract the belt partially A clicking noise should be heard as the belt retracts indicating that the retractor is in the Automatic Locking Retractor ALR mode 3 Grasp the seat belt and try to pull out the retractor The belt must lock and not extend any further If neces sary replace the retractor assembly 4 Allow the entire length of the belt to retract to cancel the automatic locking mode ELR Function Moving Check WARNING Perform the following test in a safe open area clear of other vehicles and obstructions for example a large empty parking lot Road surface must be paved and dry DO NOT perform the following test on wet or gravel roads or on public streets and highways This could result in an accident and serious personal injury The driver and passenger must be prepared to brace themselves in the event the retractor does not lock 1 Fasten drivers seat belt Buckle a passenger into the seat for the belt that is to be tested 2 Proceed to the designated safe area 3 Drive the vehicle at approximately 16 km h 10 MPH Notify any passengers of a pending sudden stop The driver and passenger must be
11. nnector CAUTION e For installing removing seat belt buckle pre tensioner connector insert a thin screwdriver wrapped in tape into Screwdriver the notch lift the lock and remove the connector e Install the connector with the lock raised and push the lock into the connector t 4 Remove screw and seat cushion inner finisher PHIA0341E 5 Remove the anchor bolt then remove front seat belt buckle from the seat frame ON Ga Pre tensioner hk Lg oy PEA D WEN ei aden a ft Ib WHIA0231E Installation Installation is in the reverse order of removal Revision July 2007 SB 5 2005 Armada SEAT BELTS Removal and Installation of Rear Seat Belt ee Second Row SEC 869 Bucket seat Ha 5 0 4 44 Dees WA A 7 49 5 0 ae AS 7 49 5 0 36 N m kg m in Ib O kg m ft lb WHIA0228E Seat belt height adjuster 2 D ring anchor bolt cover 3 D ring anchor Seat belt retractor and beltassem 5 Seatbelt buckle 6 Seat belt retractor cover bly Push pin 8 Seatbelt retractor and belt assem 9 Seat belt bezel bly Seat belt buckle 11 Seat cushion finisher 12 Seat belt lower anchor Revision July 2007 SB 6 2005 Armada SEAT BELTS REMOVAL Se ge Remove seat belt lower anchor cover and bolt Remove the D ring anchor bolt cover and D ring anchor bolt Remove the upper and lower luggage area trim Re
12. old both ends of the wire and pull taut while moving it up and down several times along the belt opening surface to remove dirt 4 Any dirt that cannot be removed with the wire can be removed by cleaning the opening with a clean cloth 5 Apply tape at the point where the belt contacts the through anchor belt opening NOTE Apply the tape so that there is no looseness or wrinkling 6 Remove the clip holding the seat belt and check that the belt returns smoothly 7 Repeat steps above as necessary to check the other seat belts Revision July 2007 SB 10 2005 Armada SEAT BELTS SEAT BELT RETRACTOR ON VEHICLE CHECK Emergency Locking Retractors ELR and Automatic Locking Retractors ALR NOTE All seat belt retractors are of the Emergency Locking Retractors ELR type In an emergency sudden stop the retractor will lock and prevent the belt from extending any further All 3 point type seat belt retractors except the driver s seat belt also have an Automatic Locking Retractors ALR mode The ALR mode also called child restraint mode is used when installing child seats The ALR mode is activated when the seat belt is fully extended When the belt is then retracted partially the ALR mode automatically locks the seat belt a specific position so the belt cannot be extended any further To cancel the ALR mode allow the seat belt to fully wind back into the retractor Check the seat belt retractors using the following test s to deter
13. s can be identified by yellow and or orange harnesses or harness connectors Precautions for Seat Belt Service ENAR CAUTION e Before removing the seat belt pre tensioner assembly turn the ignition switch OFF disconnect both battery cables and wait at least 3 minutes e After replacing or reinstalling seat belt pre tensioner assembly or reconnecting seat belt pre ten sioner assembly connector ensure entire SRS operates properly Refer to SRS 20 SRS Opera tion Check Do not disassemble buckle or seat belt assembly Do not reuse seat belt anchor bolts after removal Replace with new ones Replace anchor bolts if they are deformed or worn out Never oil tongue and buckle If any component of seat belt assembly is questionable do not repair Replace the whole seat belt assembly If webbing is cut frayed or damaged replace seat belt assembly When replacing seat belt assembly use a genuine NISSAN seat belt assembly AFTER A COLLISION WARNING e Inspect all seat belt assemblies including retractors and attaching hardware after any collision e NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the collision was minor and the belts show no damage and continue to operate properly Failure to do so could result in serious personal injury in an accident Seat belt assemblies not in use during a collision should also be replaced if either damage or improper operation is noted Seat
14. t bly 4 Seat belt lower anchor 5 Lower anchor bolt cover 6 Seat belt buckles 7 D ring anchor bolt cover 8 D ring anchor REMOVAL Remove the D ring anchor bolt cover and D ring anchor bolt Remove the lower anchor bolt cover and lower anchor bolt Remove the upper and lower luggage side finishers Refer to El 37 LUGGAGE FLOOR TRIM Remove the seat belt retractor anchor bolt and retractor and belt assembly Remove bolt from seat belt anchor base and remove seat belt buckles TOS Revision July 2007 SB 8 2005 Armada SEAT BELTS INSTALLATION Installation is in the reverse order of removal e Ensure that seat belt height adjuster is locked in the lowest position during installation Seat belt anchor base should be flat to the floor during installation and not on the anti rotation bead Third Row Center Ee REMOVAL AND INSTALLATION O 49 5 0 36 9 N m kg m ft lb REMOVAL 1 Remove the rear roof finisher Refer to El 37 LUGGAGE FLOOR TRIM 2 Lower the rear portion of the headliner 3 Remove the seat belt retractor anchor bolts and retractor and belt assembly INSTALLATION Installation is in the reverse order of removal Revision July 2007 SB 9 2005 Armada SEAT BELTS Seat Belt Inspection EHS0028U AFTER A COLLISION WARNING Inspect all seat belt assemblies including retractors and attaching hardware after any collision NISSAN recommends that all seat belt assembl
Download Pdf Manuals
Related Search