illuminated chrome cover kit for fairing mount - Harley
Contents
1. J05872 4of42. mirror assembly Make sure the locating pin is secured in the small hole of the backing plate e Install flange nut Tighten to 20 30 in lbs 2 3 3 4 Nm f Repeat steps for the opposite side J05872 Electrical Connections 1 See the service manual Remove turn signal bracket assembly See Figure 2 Locate and disconnect turn signal connector 2 from turn signal harness connector 31L or 31R 1 Route the wires of the mirror cover down to the turn signal connector Secure the mirror cover wires with cable straps Install the Y harness 3 to each of the turn signal harness connector See the service manual connector appendix Install the pins of the mirror cover wires to the connector housing Figure 3 item 6 Install the wires into the housing so that wires will connect to the same color wire on the Y harness See Figure 2 Connect the mirror cover connector to the Y harness 3 See the service manual Connect the turn signal connector 2 to the Y harness then install turn signal bracket assembly Repeat the procedure for the opposite side mirror cover is07679 Turn signal harness connector female Turn signal connector male Y harness Mirror cover connector AON A Figure 2 Auxiliary Fog Lamp Assembly 2of4 FINAL ASSEMBLY Proper operation of mirror cover lamps is a Mirror cover lamps are not lit during normal vehicle 1 Secure all wiring away from any moving parts pinch poi
3. cMOTOR HARLEY DAVIDSON WY J05872 INSTRUCTIONS REV 2013 10 10 ILLUMINATED CHROME COVER KIT FOR FAIRING MOUNT MIRRORS GENERAL Kit Number 56000084 Models For model fitment information see the P amp A Retail Catalog or the Parts and Accessories section of www harley davidson com English only NOTES The mirror covers in this kit are not intended to replace the stock turn signals Mirror cover turn signals will not function properly without the stock turn signals installed Tools and Supplies Required WARNING The rider s safety depends upon the correct installation of this kit Use the appropriate service manual procedures If the procedure is not within your capabilities or you do not have the correct tools have a Harley Davidson dealer perform the installation Improper installation of this kit could result in death or serious injury 00333a NOTE This instruction sheet refers to service manual information A service manual for this year model motorcycle is required for this installation and is available from a Harley Davidson dealer Electrical Overload NOTICE It is possible to overload your vehicle s charging system by adding too many electrical accessories If the combined electrical accessories operating at any one time consume more electrical current than the vehicle s charging system can produce the electrical consumption can discharge the battery and cause damage to the vehicle s elec
4. nts operation or extreme heat b The proper mirror cover lamp flashes along with the NOLE corresponding turn signal when activated Verify that the ignition light key switch is in the OFF position pened g before installing the main fuse attaching the battery cables c BOTH mirror cover lamps flash when the emergency i flashers are activated 2 See the service manual Install main fuse 3 Turn the ignition light key switch to IGNITION but do not 4 See the service manual Install outer fairing start the motorcycle Test for proper turn signal and mirror Adjust the mirrors for proper field of vision and compliance cover lamp operation with local regulations J05872 3 of 4 SERVICE PARTS isO7668 Figure 3 Service Parts Illuminated Fairing Mounted Mirror Cover Kit Table 1 Service Parts Table ltem Description Quantity Part Number 1 Mirror cover right Not Sold Separately 2 Mirror cover left Not Sold Separately 3 Grommet 2 Not Sold Separately 4 Terminal pin 20 22 AWG 6 72910 11 5 Seal pin 6 5118 6 Housing 4 way pin JAE 2 72908 11 7 Y harness 2 69200880 8 e Housing 4 way socket JAE 72908 11 9 e Terminal socket 20 22 AWG 72910 11 10 e Housing 4 way pin JAE 2 72907 11 11 e Terminal pin 20 22 AWG 72909 11 12 Alcohol packet not shown Not Sold Separately 13 Primer packet not shown Not Sold Separately
5. posite side NOTE Make sure ambient temperature is at least 50 F 10 for proper adhesion of the mirror cover to the mirror 6 Clean the back surface of the mirrors with the alcohol pad provided Allow to dry completely 7 Obtain the primer tube from the kit and follow the instructions on the tube to activate the primer When the primer is activated apply the primer to the back surface of one mirror 1 of 4 Please dispose of materials responsibly isO7561a Mirror assembly Backing plate Flange nut Hole location Mirror cover Grommet Mirror cover wire NONNA Figure 1 Mirror Cover Installation NOTE The Illuminated Chrome Mirror Covers are side specific The covers install with the wire harness exiting from the bottom 8 Obtain the correct mirror cover from the kit Rub the liners on the three pads on the back surface of the mirror cover to activate the adhesive Then remove the liners 9 Place the mirror cover over the back surface of the mirror and press into place for a minimum of 60 seconds 10 Repeat Steps 7 through 9 for the remaining mirror and cover 11 Position the mirror on the outer face of the inner fairing with the rounded side of the mirror outboard a See Figure 1 Insert the mirror cover wire 7 through the drilled hole 4 b Secure wiring grommet 6 in drilled hole c Insert the mirror post through the original mirror mounting hole d Install backing plate over
6. trical system See an authorized Harley Davidson dealer for advice about the amount of current consumed by addi tional electrical accessories or for necessary wiring changes 00211Cc WARNING When installing any electrical accessory be certain not to exceed the maximum amperage rating of the fuse or circuit breaker protecting the affected circuit being modi fied Exceeding the maximum amperage can lead to elec trical failures which could result in death or serious injury 00310a J05872 amp Many Harley Davidson Parts amp Accessories are made of plastics and metals which can be recycled The Illuminated Chrome Mirror Cover Kit requires up to 100 mA additional current from the electrical system Kit Contents See Figure 3 and Table 1 INSTALLATION Preparation Models with main fuse WARNING To prevent accidental vehicle start up which could cause death or serious injury remove main fuse before pro ceeding 00251b 1 See the service manual Remove main fuse Installation 1 See the service manual Remove outer fairing 2 See Figure 1 Remove the mirrors 1 flange nuts 3 and plastic backing plates 2 securing the mirrors to each side of the inner fairing Retain all items 3 Measure 1 in 25 mm outboard 4 from the large mirror stud hole in the inner fairing and make a mark 4 Drilla 1 4 inch 6 mm diameter hole through the inner fairing at the mark 5 Repeat Steps 3 and 4 for op
Download Pdf Manuals
Related Search