II 011513 J02C IKP.xlsx
Contents
1. Extended Storage Switch in the 2b To remove transit mode is by doing as follows cabin fuse block Once located check that 1 Remove fuse cover lid it is in the Customer position See below 2 Push down shorting pin for reference 3 Ign On 2 times without turn the vehicle on Inventory Customer PULL UP PUSH DOWN To put transit mode back is by doing as follows 1 Ign Off 2 Remove fuse cover lid oe A 3 Pull up shorting pin INCORRECT CORRECT 4 Assemble fuse cover lid 5 Ign On 2 times without turn the vehicle on a Canfiem teancit mada randitinn nan matar NOTE Typical vehicle condition shown above Switch is easily identifiable by the permanent push pull fuse holder Actual position on the fuse block may vary vehicle to vehicle A CAUTION e Make sure the ignition is OFF before changing the switch position Condition Vehicle is delivered to the dealer Inventory Condition S Technician performs PDI Customer test drives the vehicle Vehicle is being stored at the dealer Inventory Condition Cis Vehicle is sold and delivered to customer Customer Delivery 4 NOTE The Extended Storage Switch is only an aid to improve battery life during vehicle storage at the dealer If the Extended Storage Switch fuse ever needs service after vehicle delivery discard the Extended Storage Switch and install the correct fuse in its place 3 Turn ignition switch to ON position 4 Record the customer radio presets and other prese2. II Rev 01 15 13 INSTALLATION PROCEDURE I LLUMI NATED KICK PLATE FRONT INSTALLATION NOTE The procedure below show the installation for LH side Repeat procedure for RH side 16 Align Illuminated Kick Plate LH B to masking tape and Inner Kick Plate 1 as shown in Fig 33 Fig 33 4 FRONT OF VEHICLE D Inner Kick Plate LH 1 LTT ne VERSA J qie N be Illuminated Kick Plate LH B DETAIL C eS Be Illuminated Kick Plate LH B Masking tape SECTION D D NOTE Make sure no visual gap between Illuminated Kick Plate B and I nner Kick Plate 1 plastic trim edge as shown in SECTION D D Fig 33 17 Apply minimum 11lb 49N of pressure along the part to secure tape to body as shown in Fig 34 A CAUTION e Use caution when applying pressure as the surface may dent Page 15 of 17 999G6 4Z000 II Rev 01 15 13 ACCESSORY CHECK Must for any accessory that uses the vehicle battery for power C Connect the battery negative terminal and tighten the nut to 5 4 N m 47 8 Ib in Check all Critical Installation Steps Check all torque values Reference related steps and figures Verify all wiring is secure and not exposed Trim all excess cable ties flush Check function Confirm RH LH VERSA text is Illuminated when either door is in the open position Manual engage door switch to verify Illuminated Kick plate turns OFF when room lamp go
3. II Rev 01 15 13 INSTALLATION PROCEDURE VEHICLE PARTS REMOVAL NOTE The procedure below show the installation for LH side Repeat procedure for RH side Masking tape Fig 4 1 Measure 45mm from front of Inner Kick plate LH 1 and 45mm mark with masking tape as shown in Fig 4 FRONT OF VEHICLE Inner Kick plate LH 1 2 Inner Kick plate LH 1 removal a Remove Inner Kick plate LH 1 by pulling straight up to disconnect clips as shown in Fig 5 3 Dashboard Side Lower panel LH 2 removal a Remove Dashboard Side Lower panel LH 2 by pulling straight up to disconnect at metal clips and locating hole shown in Fig 6 Locating hole Dashboard Side Lower panel LH 2 4 Repeat steps 1 through 3 for RH side of vehicle Inner Kick plate RH 3 Dashboard Side Lower panel RH 4 Page 5 of 17 999G6 4Z000 II Rev 01 15 13 INSTALLATION PROCEDURE WIRING HARNESS INSTALLATION NOTE The procedure below show the installation for LH side Repeat procedure for RH side 4 CAUTION e Connector pull test should be less than 10kgf 22 Ibs to confirm secure connection to vehicle Accessory Service Connector 1 Wrap harness fuse C with Gray urethane foam tape F as shown in Fig 7 2 Locate the Driver side Accessory Service Connector Part No 999Q9 AY000 as shown in Fig 8 Note A previously installed accessory may be present If so carefully remove the Accessory Service Connector from the vehicle harness
4. before Posi foam tape F tapping It is recommended that all Posi tapping be completed before reattaching the Accessory Service Connector to the vehicle harness AOC Fig 8 Note Be sure to grab the connector and not the harness 9 when separating the plug from the foam tape 3 Connect Wire harness C to Accessory Service Connector E view An Part No 999Q9 AY000 with Posi Tap H as shown in below Illustration THi2FW NH aA Detail View A Accessory Service Connector Accessory Service Connector hii n Signal Color Color Battery Saver PINK Room Lamp Output YELLOW WHITE Harness C Note See next page on how to use Posi tap Fig 9 4 Using a Posi Tap H connect the White wire from White wire Wire harness C to the Yellow wire on the Accessory Service Connector as shown in Fig 9 Yellow wire 5 Using a Posi Tap H connect the Red wire from Wire harness C to the Pink wire on the Accessory Shrink wrap Service Connector as shown in Fig 9 Note Be sure NOT to Posi Tap through the shrink wrap Pink wire tubing Shrink wra Page 6 of 17 999G6 4Z000 II Rev 01 15 13 INSTALLATION PROCEDURE WIRE HARNESS INSTALLTION 6 Accessory Service Connector Fig 11 7 i Straight and evenly spaced all the way around ii Tight and minimize gap wire jacket should be crushed 8 f Tighten 9 i Straight and evenly spaced all around ii Tight and no gap and test the
5. of the loop c up toward the body of the posi tap from b measure 1 25 4mm then make the second bend of the loop d in towards the posi tap so it can be secured with electrical tape Reference 999M1 NADSO Page 7 of 17 999G6 4Z000 II Rev 01 15 13 INSTALLATION PROCEDURE WIRE HARNESS INSTALLTION 11 Securing the tapped accessory a Secure the pierced wire and the tapped wire on the non pierce side to the body of the tap with electrical tape 2 revolutions b Secure the pierced wire and the tapped wire on the non pierce side to each other with electrical tape 2 revolutions 12 Putting a second tap on the same wire a Tap first accessory then form a strain relief loop as shown in Fig 1 thru 5a Do not secure wire until additional tap has been installed b Measure 1 25 4mm from point b to point c and install the second accessory tap Bend the wire gently to form the staircase shape c After tapping the second accessory form a strain relief loop d as shown in Fig 5a 13 Securing multiple accessory taps a Secure the pierced wire and the tapped wire on the non pierce side to the body of the tap with electrical tape 2 revolutions b Secure the pierced wire and the tapped wire on the non pierce side from the first posi tap to the body of the 2nd tap with electrical tape 2 revolutions c Secure the pierced wire from the last tap and the tapped wires from the non pierced sides of each tap to eac
6. switch is placed in the inventory position Refer to the Extended Storage Switch verbiage at the beginning of the INSTALLATION PROCEDURE section O UUU Re program radio presets and other vehicle settings to the recorded settings No need to do this step if the extended storage switch is placed in the inventory position NOTE Posi TapT is protected by patent 5 228 875 5 695 369 5 868 589 6 692 313 Jap 2881414 Aus 708700 Tia 103534 Can 2204826 Mex 200626 Korea 477279 China Z197105562 9 amp others pending Page 17 of 17 999G6 4Z000 II Rev 01 15 13
7. GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION Illuminated Kick Plate APPLICATION VERSA PART NUMBER 999G6 4Z000 KIT CONTENTS i mmen O o 99908 OI i Illuminated Kick Plate LH 9996 42020 2 Wire Harness e frie Wrap rong Tie Wrap Gray Urethane Foam Tape Black Urethane Foam Tape Posi Tap 1 Installation Instructions Replacement Template 2 Accessory Service Connector NOT INCLUDED IN KIT 999Q9 AY000 1 1 1 TOOLS REQUI RED Nylon Removal Tool Wire Cutter e 10mm Socket Masking Tape Flash Light e Scissors Ruler Soft non Linting Towel e 50 50 alcohol amp water solution File Soap and Water Page 1 of 17 999G6 4Z000 II Rev 01 15 13 INSTALLATION PROCEDURE PRE INSTALLATION CAUTIONS NOTES A CAUTION Dealer Installation Recommended Instructions refer to Service Manual Please read this instruction carefully before installing this product for correct installation Please DO NOT use or install the part in ways other than what is described in this instruction manual If problem occurs during installation please contact Nissan dealer where you purchased the product 1 Apply parking brake 2 Confirm the vehicle is no longer in the default shipping state Extended Storage Switch Pulled Up and BCM in Transit Mode Failure to confirm the vehicle has been removed from this state will result in the loss of normal vehicle operation The confirmation requires two checks 2a Locate the
8. N Do not attach the harness to sharp metal edge FRONT OF VEHICLE Page 12 of 17 999G6 4Z000 II Rev 01 15 13 INSTALLATION PROCEDURE I LLUMI NATED KICK PLATE INSTALLATION NOTE The procedure below show the installation for LH side Repeat procedure for RH side 11 Attach excessive Wire harness C to the vehicle harness with Tie wrap D as shown in Fig 29 Tie wrap D a aa YE 4 CAUTION e Do not attach the harness to sharp metal edge Wire Harness C A FRONT OF VEHICLE 12 By using file remove surface as shown in section B B on edge of Inner Kick plate 1 at location of 120mm from front end as shown in Fig 30 Inner Kick plate LH 1 A File banun on ae ore Inner Kick plate LH 1 35mm Ne A u 120mm D T Page 13 of 17 999G6 4Z000 II Rev 01 15 13 INSTALLATION PROCEDURE I LLUMI NATED KICK PLATE INSTALLATION NOTE The procedure below show the installation for LH side Repeat procedure for RH side Filed area Inner Kick Plate LH 1 13 Reinstall Dashboard Side Lower panel LH 2 OQ te 14 Reinstall Inner Kick Plate LH 1 LED wire is Sandi At that time route the LED unit wire to filed area as shown in Fig 31 Se pa LED unit wire Inner Kick Plate LH 1 a Pamm LLU LED unit wire 2 Illuminated Kick Plate LH B FRONT OF VEHICLE ie FRONT OF VEHICLE Inner Kick Plate 1 Dashboard Side Lower panel LH 2 s liners Page 14 of 17 999G6 4Z000
9. es OFF O UUUUO Check all vehicle electrical systems that the accessory interfaces with Vehicle electrical system 1 Must for pre wiring overlay harness and Posi Tap Vehicle electrical system 2 Electrical system s that the accessory connects to RE I NSTALLATI ON OF REMOVED PARTS C Re install all removed vehicle parts Refer to the vehicle service manual as necessary C Clean interior of vehicle Page 16 of 17 999G6 4Z000 II Rev 01 15 13 FINAL INSPECTION C Verify re installed trim parts for proper flush fit no gap no waviness etc Verify all clips are fully engaged and locked Verify re installed trim parts are free from cracks scratches or stress marks Verify vehicle headliner seat steering wheel center console floor carpets etc are not soiled Verify interior and exterior is not damaged O 0O ODO L Turn ignition switch to ON and confirm proper operation of Vehicle Systems If equipped verify all window and sunroof one touch operation and perform the reset procedure if necessary Refer to the vehicle service manual for more details C Confirm proper audio function AM FM SAT CD and AUX Start engine and verify that there are no new Diagnostic Trouble Code Turn ignition switch to OFF Place the Owner Manual Quick Reference Guide and or other Manual in the glove box If this vehicle will be returned to a dealer lot or showroom for an extended period of time be sure the extended storage
10. h other with electrical tape 2 revolutions NOTE The Accessory Service Connector is only for the installation of Genuine Nissan or Nissan approved accessories Nissan shall not otherwise be liable for loss or damages due to the installation of non approved accessories Reference 999M1 NADSO Page 8 of 17 999G6 4Z000 II Rev 01 15 13 INSTALLATION PROCEDURE WIRING HARNESS INSTALLATION NOTE The procedure below show the installation for LH side Repeat procedure for RH side 14 Cut one piece of Gray urethane foam tape F in half Then Wrap the Posi Taps with Gray Urethane foam tape F to prevent rattle as shown in Fig 18 Use other half piece of Gray urethane foam tape for RH side 15 Then plug the Accessory Service Connector into the vehicle harness on the driver side Gray Urethane Foam Tape F 16 Attach fuse on Wire harness C to vehicle harness at the position as shown in Fig 19 by Long tie wrap E 1 place Vehicle wrap E Fuse Harness C 17 Repeat steps 1 through 16 for RH side of vehicle Page 9 of 17 999G6 4Z000 II Rev 01 15 13 INSTALLATION PROCEDURE WIRING HARNESS INSTALLATION NOTE The procedure below show the installation for LH side Repeat procedure for RH side 18 Function check a Connect Wire harness C to Illuminated Kick Plate LH B LED unit wire as shown in Fig 20 RH side is A b Connect battery c Check function Confirm RH LH VERSA text
11. is Illuminated when either door is in the open position Manual engage door switch to verify Illuminated Kick Plate turns OFF when room lamp goes OFF as shown in Fig 21 LED unit wire d If OK disconnect Wire harness C from the lamp unit harness of Illuminated Kick plate B RH side is A e If NG check harness routing connections and LED unit to identify root cause Repeat Illuminated Kick Plate LH B steps a to c until unit is properly working opposite RH side is A f Disconnect battery as shown in Fig 22 Page 10 of 17 999G6 4Z000 II Rev 01 15 13 INSTALLATION PROCEDURE I LLUMI NATED KICK PLATE INSTALLATION NOTE The procedure below show the installation for LH side Repeat procedure for RH side 1 Clean the Illuminated Kick Plate attachment area as Shown in Fig 23 with 50 50 alcohol amp water let dry for 30 seconds Illuminated Kick Pate attachment area KS Fig 24 2 Set Illuminated Kick Plate LH B to body side panel as FRONT OF VEHICLE shown in Fig 24 Then confirm the position of the Black Urethane Foam Tape attachment area Note Do Not remove tape s liner of Illuminated Kick Plate LH B at this time Black Urethane Foam Tape attachment area 3 Remove Illuminated Kick Plate LH B 4 Clean the Black Urethane Foam Tape attachment area as Shown in Fig 24 with 50 50 alcohol amp water let dry for N 30 seconds Illuminated Kick Plate LH B SECTI ON A A 15mm Illumi
12. nated Reference Kick Plate LH B lt Illuminated Kick Plate LH B 5 Attach the Black Urethane Foam Tape G to vehicle panel flange as shown in Fig 25 6 Set Illuminated Kick Plate LH B to body side panel as shown in Fig 24 Note Do Not remove tape s liner of Illuminated Kick Plate LH B at this time Black urethane foam tape G 7 Place the LED unit harness on top of the Black Urethane LED Unit Wire Foam Tape H then apply another else hse THane foam Tape G on top of the harness as shown in Fig 25 Vehicle Panel of Flange Page 11 of 17 999G6 4Z000 II Rev 01 15 13 INSTALLATION PROCEDURE I LLUMI NATED KICK PLATE INSTALLATION NOTE The procedure below show the installation for LH side Repeat procedure for RH side 8 Route LED unit wire of Illuminated Kick plate LH B into Front OF VEHICLE harness protector as shown in Fig 26 Illuminated Kick plate LH B Harness protector LED unit wire S SN KS Illuminated Kick plate LH B 7 A ee fee og es a aa ___ CvERSA_ es 9 Connect LED unit wire B to Wire harness C then cut one piece of Gray Urethane Foam Tape F in half apply one half around connecting section as shown in Fig 27 Use other half piece of Gray Urethane Foam Tape for RH side LED unit wire Wire Harness C 10 Secure Wire harness C to vehicle harness with Tie wrap D as shown in Fig 28 2 place Connector Aa CAUTIO
13. signal 10 Service Connector Harness 25 4mm Bie Accessory Harness 25 4mm Tap vehicle wire a Identify and confirm correct wire in the Accessory Service Connector to be tapped b Remove cap slot side from tap body c Slide cap around single accessory wire d Position cap gt 0 25 6 35mm away from the heat shrink end of Accessory Service Connector e Tighten the tap TIGHT with finger pressure f Tighten by another quarter turn NOTE Figures are not to scale Do not re use the tap Inspect the tap to ensure correct installation NOTE Avoid putting pressure on the vehicle wire and tap for the remainder of the installation Tap accessory wire a Remove tap non pierce side from tap b Remove the protective stub from the wire c Insert wire through the non pierce side opening d Spread the individual strands into fan shape e Insert wire into the tap body and ensure that it is all the way in f Tighten the tap TIGHT with finger pressure g Tighten by another quarter turn Confirm the tapped accessory wire a Pull on the wire lightly to ensure connection b Inspect the tap to ensure correct installation c Test the signal to ensure that it is working properly Forming strain relief loop always required a Gently bend the end of the pierced wire where it exits the cap down towards body of posi tap b Starting at b measure 1 25 4mm then make the first bend
14. ts as required 5 Put shift lever in P position for A T and CVT or ist for M T 6 Turn ignition switch to OFF position Page 2 of 17 999G6 4Z000 II Rev 01 15 13 INSTALLATION PROCEDURE PRE INSTALLATION CAUTIONS NOTES 7 Disconnect the negative battery terminal 8 Use seat and floor protection 9 This part is to be installed at surface temperature of 65 100 deg F INSTALLATION OVERVIEW 1 Remove the following vehicle parts in the sequence shown below Store these re usable parts in a safe and protected manner Removal Sequence Inner Kick Plate LH Dashboard Side Lower Panel LH Inner Kick Plate RH Dashboard Side Lower Panel RH Page 3 of 17 999G6 4Z000 II Rev 01 15 13 INSTALLATION OVERVIEW 2 Installation Outline Fig 3 Connect to Accessory Service Connector Wire harness A CAUTION e Vehicle wiring color description is just for reference Please refer to vehicle wiring diagram for details 3 Mechanization Signal Color Size ACCE SSORY Battery Saver SERVICE CONNEC TOR Room lamp Output Part 999Q9 AYOOO TH12FW NH Room lamp output Battery saver C E e E Kick Plate FUSE 3A T Signal Color ACCE SSORY Battery Saver SERVICE CONNEC TOR Room lamp Output Yellow Part 999Q9 AY000 TH12FW NH Room lamp output Battery saver FUSE 3A a in tl Kick Plate Page 4 of 17 999G6 4Z000
Download Pdf Manuals
Related Search