H.I.T. 5000H - Automotive Equipment Svc Co Inc
Contents
1. 16 Move the camage to the extended position thus pulling the inner tire out of the outer tire If the two tires are not separated when the camiage has reached its extended position further travel can be reached by raising the vertical cylinder until the two tires are separated 17 Remove the web strap from the inner tire and remove the outer tire from the clamps of the machine COATS H I T 5000H Changer 9 Mounting N 1 Place the two inner tire side plates into the car nage forward holes facing each other as shown above 2 Place the shortest nylon web strap down on the center of the two side plates Note Ensure that the ratchet end of the strap is to the outboard of the side plates and the flat side is facing up 3 Roll the inner tire over the strap and between the two side plates Ensure that the two slits in the inner tire are placed opposite one another and parallel to the ground 4 Compress the inner tire by pushing down on it with the clamps Note The jaws should be spread to a point that the arms are parallel to the ground While compressing the inner tire ensure that the inner tire is maintained in a vertical position 5 After the inner tire is compressed to its lowest point place strap around inner tire and tighten with socket and ratchet as shown above 10 COATS H 1 T 5000H Changer 6 Raise the clamps and remove the strapped inner tire from the side plates Th2. AN 5 Using one of the tire tools to assist the bead into drop center continue rotating the chuck until the inner bead is mounted 6 Insert the inner tube and repeat the above steps to mount the outer bead Note Avoid damage to the valve stem by never allowing the stem to pass the stationary tool COATS H I T 5000H Changer 7 Hutchinson Run Flat Tires Demounting 1 By operating the carriage to the extended posi tion the table will be rotated to the honzontal position 2 Place the tire and rim over the table top by rolling into place and then leaning back onto the table 3 Again using carriage handle rotate table back to vertical position As this occurs the tire and rim will fol low and end up sitting on top of the table A CAUTION Ensure that table cylinder is retracted when the above operation is done so there will be no damage to the cylinder shaft 8 COATS H I T 5000H Changer 4 When the table is in the vertical position manually center the tire and rim so that it lies perpendicular to the table cylinder 5 Place the tire compressor on top of the tire and pin it to the clevis affixed to the table cylinder A CAUTION Adjust the four arms of the compressor to just clear the lock ring Tighten all of the T handles so they won t move A WARNING Ensure at this point that the tire has been completely deflated and the valve core
3. support during lifting activities and are also helpful in providing operator protection Consideration should alSo be given to the use of hear ing protection if tire service activity is performed in an enclosed area or if noise levels are high iv COATS H I T 5000H Changer Definitions of Hazard Levels Identify the hazard levels used in this manual with the following definitions and signal words DANGER Watch for this symbol A DANGER It Means Immediate hazards which will result in severe personal injury or death WARNING Watch for this symbol It Means Hazards or unsafe practices which could result in Severe personal injury or death CAUTION Watch for this symbol It Means Hazards or unsafe practices which may result in minor personal injury or product or property damage Watch for this symbol It means BE ALERT Your safety or the safety of others is involved Safety Instructions Only properly trained personnel should service tires on the H T 5000H Read all safety and operating instructions thor oughly before using the tire changer ALWAYS remove all wheel weights and the valve core to deflate the tire before servicing ALWAYS cover the electric motor and switch box before hosing down the tire changer Be sure water does not enter the motor or switch box ALWAYS disconnect the electric power and air sup ply before attempting any maintenance ALWAYS keep all working surfac
4. the tire being careful not to contact the nm 7 Move the bead loosening disc to the rear of the tire and repeat the steps above to loosen the rear bead Note Tire lubricant is very important in the demount ing and mounting process While the bead loosening tool is pushing the bead away from the rim edge lib erally lube both beads and the rim FAILURE TO APPLY LUBE COULD RESULT IN DAMAGE TO THE TIRE BEAD Note Applying a liberal amount of lube to the tire sidewall prior to bead loosening will make the tire more pliable and therefore reduce the likelihood of damage to the sidewall Demountng 1 If the rim has an inclined edge of 15 degrees con tinue the bead loosening procedure for the rear bead until the tire has been pushed off the rim A CAUTION The bead opposite the disc must be in the drop center of the rim Damage to the bead may occur if the bead is not in the drop cen ter 2 If the rim has no edge or has a stiff sidewall retract the disc and remove it from the camage Place the combo tool and tee into position near the outer rim edge COATS H I T 5000H Changer 3 Y Ve y p 2 4 k i i BEN pr k 3 Tighten the locking handle and move the tool into position near the edge of the rim as shown above 4 Insert the bead lifting tool between the rim and bead at a point near the right side of the tool i 4 kh he 5 Pry the bead out over the rim Note You ma
5. the ring s COATS H I T 5000H Changer 5 Farm Tires Bead Loosening 1 Remove the valve core Deflate the tire away from the machine and remove any calcium chloride or other substances from the tire prior to rolling the wheel onto the tire changer 2 After locking the wheel on the chuck move the bead loosening disc into position near the edge of the nm Ta 4 Note Apply a liberal amount of lube to the tire side wall This will regain some of the original flexibility of the rubber thus reducing possible damage to the side wall 3 Rotate the wheel and slowly move the bead loos ening disc into the sidewall until the bead is loosened 6 COATS H I T 5000H Changer 4 Continue to rotate the tire and apply a liberal amount of lube to the bead and the rim 5 Move the bead loosening tool to the inner bead and repeat the above steps Note Tire lubricant greatly reduces the force needed to demount or mount a tire Liberally lube each bead and rim edge while the bead loosener disc holds the bead away from the rim FAILURE TO APPLY LUBE COULD RESULT IN DAMAGE TO THE TIRE BEADS 1 Advance the combo tool close to the rim with the finger past the nm edge 2 With the spade tool inserted between the rim and the outer bead on the right of the combo tool pry the bead out over the rim edge 3 Rotate the wheel counterclockwise
6. while main taining pressure on the spade tool until the outer bead Is demounted Push the valve stem inside the rim and pull the inner tube out of the tire Note It is possible to roll one or both beads s off the rim with the bead loosener disc instead of the combo tool However care must be taken not to damage the tube or the valve stem By alternately rotating the wheel first counterclockwise then clockwise being careful not to pass over the valve stem the tire may be demounted using this method If the tire is wide the rim is thin or weak or the side wall is tough do not use this method since the bead or the rim may be dam aged Note Tire lubricant greatly reduces the force needed to demount or mount a tire Liberally lube each bead and rim edge while the bead loosener disc holds the bead away from the rim FAILURE TO APPLY LUBE COULD RESULT IN DAMAGE TO THE TIRE BEADS Mounting 1 Lube both beads and the rim liberally 2 Rotate the rim so the valve stem hole is directly on the bottom then roll the wheel onto the camage tod ioe a i 3 A gt 3 Move the combo tool into position near the edge of the rim Note Mounting of the outer bead is shown in order to see the position of the tools Position of the tools will be the same for the inner bead 4 Lean the tire against the rim and clamp the vise grip on the edge of the rim to the left of the combo tool Rotate the chuck to lift off the carriage
7. Gats H I T 5000H TRUCK TIRE CHANGER Installation Instructions Operating Instructions Safety Instructions Maintenance Instructions READ these instructions before placing unit in service KEEP these and other materials delivered with the unit in a binder near the machine for ease of reference by supervisors and operators HENMNESS ViINDUSTRIES inc 1601 J P Hennessy Drive LaVergne TN USA 37086 3565 615 641 7533 800 688 6359 HENNESSY INDUSTRIES INC Manufacturer of AMMCO COATS and BADA Automotive Service Equipment and Tools M anual Part No 8109499 00 Revision 8 00 ii COATS H I T 5000H Changer Table of Contents Operator Protective Equipment un IV Definitions of Hazard Levels un IV Safety Instructions Bead Loosening surcar a geo dem A o Satele ae ah ae om ta d o de Th Ma Ae be e ad i de ai V Demounting amp MOUNTING 0c eee teen V V MSG se Aa M EEG INSTa lati Ler As dia a M Principal Operating Parts SPEcINC LOIIS ni sn aa tota c atit 3 a And i i ii i a e 3 a iti dl tv ste e Rae 1 NES ND ere 2 Tubeless Duplex amp Supersingle Tires Bead LOOSENING x sia e a ura ae eee id da ae Hehe 0 a a sr 3 DET OUT vaner TN lea a as n la Sas deck il e 3 MATING Gr 4 Wheels with Lock Rings Bead Loosening and Demounting sy rane 5 MOUNINO area ace dad Sa ee ie aa H NA SST 5 Farm Tires Bead LOOSENING tia AA A 6 Snow 6 MOI Fres TLL 7 Hutch
8. d Regulations such as the Federal OSHA Standard Number 1910 177 NEVER seat beads or inflate a tre on the tre changer The HAT 5000H is not designed as a safety device or stand for bead Seating or inflation ALWAYS use an approved inflation chamber or infla tion cage COATS H I T 5000H Changer ev Installation It is not necessary to bolt the H I T 5000H to the floor However if desired use the holes provided in the base of the machine Most electrical codes require machinery that is permanently installed to be wired directly to the power source via conduit Remove the H I T 5000H from the shipping pallet and position on a relatively level and smooth floor preferably concrete Important Read this operators manual thoroughly before attempting to change any tires Also actuate the controls several times to become familiar with their function and direction vi 9 COATS H I T 5000H Changer Electric Installation The H I T 5000H requires 220 volts 60 cycle single phase power with a 20 amp circuit An optional model is available for 110 volt single phase Important Have a licensed electrician connect the H I T 5000H to the power source The licensed elec trician must sign the warranty registration card to val idate the warranty Principal Operating Parts Oil Reservoir Pressure Adjusting Cap Knob Hydraulic Pressure Gauge On Off Switch TE FN Wheel Chuck Clamp Con
9. e jaw clamps up or down to the approximate center of the wheel Refer to the wheel drawings on this page for suggested meth ods of clamping various types of wheels 4 Lower the jaw clamps until you can position the wheel on the top jaw clamp Raise the chuck which will also raise the wheel off the platform 5 Slowly retract the jaw clamps until the wheel falls into the proper position for clamping Clamp the wheel by pulling the control lever toward you until the hydraulic motor stalls Release the handle and the wheel is ready for mounting or demounting Tubeless Duplex and Supersingle Tires Bead Loosening 1 After locking the wheel on the chuck remove the valve core and deflate the tire completely 2 Position the bead loosening disc in one of the square holes in the camage closest to the outer edge of the tire 3 Rotate the tire While the tire is rotating slowly advance the bead loosening disc to contact the tire bead Adjust the chuck up or down so the disc is close A CAUTION Do not contact the rim with the bead loos ening disc Damage to the rim may result 4 Once the rim edge is cleared the chuck may be lowered to move the disc closer to the tire bead Continue moving the disc toward the machine until the bead is loosened 5 While the tire is still rotating apply a liberal amount of tire lubricant to the tire bead and the rim 6 Raise the chuck and back the tool away from
10. en remove the side plates from the camage 7 Roll the outer tire onto the camage and clamp the bead into the deepest V in jaws A CAUTION The hydraulic pressure regulator knob located on the swinging pod front should again be set at minimum pressure Also care should be taken to ensure that the beads are not overly stretched 8 Place the two bead spreaders into the lower edge of the bead with the other end hooked into the open ings of the tire ramps angles welded to the side rails Then lift the tire up until the bead is spread open Slightly Note Apply a liberal amount of lube to the front bead of the outer tire and the edges of the spreaders in the area of the bead 9 Place the combo tool tee into the carriage with 14 Remove short web strap from inside of outer the tee perpendicular to the carriage cylinder and plat tire form on the side facing outer tire Also extend carriage 15 Lower both tires to carriage and remove from 10 Start inner tire into outer tire and place lower machine end onto ie of combo tool sl 16 Extend carriage rotating table to horizontal posi tion 11 Move caniage rearward retract and push inner tire into outer tire 17 Place rim over table top and tire over cylinder Shaft Apply liberal amount of tire lube to rim as shown above 18 Extend table cylinder shaft fully Now retract car nage cylinder and rotate table tire and r
11. es clean and free of tire lube buildup ALWAYS be aware of what each person is and will do before attempting any two person operation Bead Loosening NEVER place anything between the bead loosener disc and the tire wheel NEVER place any part of your body between the bead loosener disc and the tirefwheel severe bodily injury may result NEVER allow the bead loosener to contact the wheel wheel damage may occur Demounting amp Mounting NEVER stand on the working table while demount ING OF mounting a tire ALWAYS keep hands feet and other objects away from moving parts while the machine in turned on ALWAYS place the narrow bead seat to the outside when damping Failure to demount the tire from the narrow bead seat side may cause damage to the tire beads ALWAYS apply an approved rubber lubricant to rim flanges and both tire beads before demountng or mounting and seating the beads NEVER use antifreeze silicone or petroleum base lubricants ALWAYS dean and inspect the wheel NEVER mount a tire on a damaged or rusty wheel Wheel damage or rust may cause tire or wheel failure during inflation Explosion from failure may result in severe injury or death of the operator and bystanders ALWAYS be sure the bead opposite the tool is in the drop center before rotating the tire when demounting or Mounting to avoid damage to the tire beads Inflation ANNAYS follow all applicable Local State and Federal Codes Rules an
12. he tire changer The H I T 5000H is not designed as a safety device or stand for bead seating or inflation ALWAYS use an approved inflation chamber or infla A DANGER Tire failure under pressure can be haz ardous Place the wheel inside an approved inflation chamber or cage before inflating Use an approved remote inflation valve hose and gauge ALWAYS wear safety gog gles for eye protection Do not stand beside the wheel or cage during inflation Keep hands and other parts of the body out of the cage during inflation Observe the tire pres sure frequently Do not exceed the manufac turers recommended maximum inflation pressure Failure to follow these instruc tions may cause the tire and nm to separate with tremendous force resulting in serious personal injury or death Tire Spreading There are two methods of spreading the tire with the roller tool Method A Method B a Mk 1 With the first bead removed hook the roller tool 1 With the tire completely demounted and the rim over the outer bead and move the tool away from the removed from the clamps hook the inner bead over rim to spread the beads and gain access to the inside the clamps and the roller tool over the outer bead of the tire M ove the tool away from the inner bead to gain access to the inside of the tire Note The wheel can be rotated with the roller tool still in place but the tool should be moved toward the
13. im to vertical position 19 Place retaining ring over cylinder shaft Now install compressor onto clevis affixed to rod end of table cylinder 12 When inner tire is inside outer tire use release rod by hooking over release bar on strap clamp as Shown above 13 After ensuring that everything and everyone is clear release strap with quick pull on release rod Inner tire will expand rapidly and with much force Ensure that release rod is used when releasing catch FAILURE TO DO SO COULD RESULT IN SERIOUS IN URIES 20 Press both tires down over rim Push tire down below lock ring groove COATS H I T 5000H Changer 11 21 Remove compressor and retaining ring 2 2 Place rim seal down around rim and under bead 23 Place retaining ring and lock ring on top of tire 2 4 Install compressor onto clevis affixed to rod end of table cylinder 25 Press retaining ring down on rim seal and outer tire bead down below lock ring groove 26 Install lock ring and insure that it is down prop erly in lock ring groove 12 COATS H I T 5000H Changer 27 Raise table cylinder and remove compressor 28 Extend camage cylinder rotating table to hon zontal position 2 9 Remove mounted tire from machine ALWAYS follow all applicable Local State and Federal Codes Rules and Regulations such as the Federal OSHA Standard Number 1910 177 NEVER seat beads or inflate a tire on t
14. in accordance with the manufacturer s instructions for operation Parts replaced under warranty will assume the remainder of the unit s warranty period Only parts and accessories manufactured by the COATS Company will be warranted as stated above and this warranty shall not apply to the tire changer or any parts thereof if parts and accessories not manufactured by COATS Company are used as replacements for or in substitution of COATS Company manufactured parts and accessories To validate warranty 1 A licensed electrician must install all electrical requirements and sign the attached warranty registration card 2 The owner must fill out the post paid warranty registration card and return it to COATS Company within thirty 30 days of installation Failure to perform 1 above will void warranty coverage on electrical and hydraulic components Failure to perform 2 may void entire warranty Service Policy Upon recognition of a problem review the Maintenance Instructions and Service Manual If further assistance is required call 800 688 6359 or your nearest Hennessy Regional Office The COATS Company will supply a replacement part no charge when it is determined by the factory or an authorized representative that the part is defective in workmanship and or material and is covered by the warranty policy The owner has the option to send the defective part to the COATS Company for inspection repair or replacement All retums to the fact
15. inson Run Flat Tires DET OUN NO TAST 8 10 Tire Spreading y AR 13 EGG 13 Mamntenante rs G 14 Truck Tire Changer Warranty Policy un Back Service OCR Back COATS H I T 5000H Changer iii Read entire manual before assembling installing operating or servicing this equipment Failure to follow danger waming and caution instructions may lead to serious personal injury or death to operator or bystander or damage to prop erty Do not operate this machine until you read and understand all the dangers wamings and cau tions in this manual For additional copies of either or further information contact Hennessy Industries Inc 1601 J P Hennessy Drive LaVergne TN 37086 3565 615 641 7533 or 800 688 6359 www ammcoats com Operator Protective Equipment Personal protective equipment helps make tire serv icing safer However equipment does not take the place of safe operating practices Always wear durable work clothing during tire service activity Loose fitting clothing should be avoided Tight fitting leather gloves are recommended to protect operator s hands when handling wom tires and wheels Sturdy leather work shoes with steel toes and oil resistant soles should be used by tire service personnel to help prevent injury in typical shop activities Eye protection is essential dur ing tire service activity Safety glasses with side Shields goggles or face shields are acceptable Back belts provide
16. ory must be authorized by the COATS Company prior to retum Freight to the factory will be paid by the owner If the machine is serviced by COATS authorized personnel labor charges will be covered for a period of 90 days after the date of installation 8109499 00 8 00 Copyright 1988 Hennessy Industries and COATS All Rights Reserved Printed in USA
17. removed from the valve stem 6 Compress the retaining ring and tire down enough to clear the lock ring Using the ring tool remove the lock ring 7 Extend the table cylinder and remove the com pressor lock ring retaining ring and rim seal 8 Rotate table to the horizontal position Remove tire and rim then replace them after turning them 180 degrees 9 Rotate table back to vertical position Note Rim face should now be on bottom 10 Reinstall compressor and pin it to the clevis affixed to the table cylinder 11 Using table cylinder press tire and inner tire down off of rim 12 Remove compressor and rim from table top 13 Rotate table to horizontal position and remove inner and outer tire from table 14 Roll tire onto camiage platform and clamp bead into deepest V in jaws A CAUTION The hydraulic pressure regulator knob ocated on the swinging pod front should be set at minimum pressure Also care should be taken to ensure that the beads are not overly stretched 15 Using the longest of the two nylon web straps place the strap around the top of the inner tire and the cross brace of the table linkage The carriage should be in the retracted position Using socket and ratchet tighten strap as shown Note The vertical cylinder should be lowered to a point where the tire just clears the carriage KG Li F
18. the bead loosener disc holds the bead away from the rim FAILURE TO APPLY LUBE COULD RESULT IN DAMAGE TO THE TIRE BEADS Wheels with Lock Rings Bead Loosening and Demounting Y 1 After chucking the wheel position the bead loosener disc against the sidewall within 1 4 inch of the lock ring Do not contact the ring 2 Rotate the wheel and slowly advance the bead loosener disc until the bead is loosened LIBERALLY LUBE THE TIRE BEAD AND RIM 3 Use the ring tool to remove the lock ring s 4 Raise the tire and move the bead loosening disc into position on the inner bead Do not contact the rim AS n En 7 pr f A y Fa a 5 W w i d J al i ul e 5 Rotate the wheel and slowly advance the disc to push the tire about half way off the wheel Push the valve stem inside the wheel then finish pushing the tire off the wheel eo The tube will be damaged if the operator fails to push the valve stem into the wheel before completely removing the tire Mounting 1 Roll the tire onto the carriage and align the rim to the center of the tire 2 Liberally lube both beads and the rim Slowly advance the carriage and guide the tire onto the rim Stop about 1 3 of the way on and insert the tube 3 Place the bead loosening disc in the camiage Position it against the tire bead and push the tire onto the rim 4 With the disc pushing on the outer sidewall install
19. trol Lever Rotation Control Lever Vertical Control Lever Horizontal Control Lever Side Plates S ep Assembly 5 Compressor Assembly 3 GG mnerTire sean Role Sade Combo Tool Tee ig Lube Bottle amp Swab Socket amp Ratchet Release Rod Short Nylon Web Strap Bead Spreaders Long Nylon Web Strap Specifications Working Area 10 Foot Wide x 12 Foot Long x 8 Foot Height Weight 1 600 Pounds Handles Tires Truck 15 Inches to 24 5 Inches Tube type and Tubeless Grader Industrial and Farm 16 Foot to 42 Inches Military Run Flats 15 Inches to 24 5 Inches COATS H I T 5000H Changer 1 2 COATS H LT 5000H Changer Wheel Clamping The self centering chuck is powered by the high pres sure hydraulic system to securely lock onto the wheel Important The hydraulic pressure regulator knob located on the swinging pod front should normally be set to 1500 PSI This pressure should be reduced when mounting or demounting weak or light weight wheels 1 Roll the wheel onto the platform with the drop center or the split ing away from the chuck Position the valve stem between two of the jaw clamps so the stem will not be damaged when the wheel is clamped 2 Rotate the chuck until one of the jaw clamps is in the 12 o clock position 3 Open the jaw clamps slightly larger than the open ing you are clamping then move th
20. wheel slightly This will relieve some of the pressure on the bead thus avoiding any damage which might occur from over stretching the bead A DANGER Tire failure under pressure can be hazardous Place the wheel inside an approved inflation chamber or cage before inflating Use an approved remote infla ton valve hose and gauge ALWAYS wear safety goggles for eye protection Do not stand beside the wheel or cage during inflation Keep hands and other parts of the body out of the cage during inflation Observe the tire pressure frequently Do not exceed the manufacturers recommended maximum infla tion pressure Failure to follow these instructions may cause the tire and rim to separate with tremen dous force resulting in serious injury or death COATS H I T 5000H Changer 13 Maintenance 1 Using a grease gun and chassis grease lubricate 3 Using a grease gun and chassis grease lubricate chuck hub bushing once every month the disk shaft on the bead roller tube once every month 2 Remove the side panels and lubricate the four posts that guide the carriage up and down Also with 4 Grease chain and check the tension once every a grease gun lubricate the bushing sprocket tube month and adjust if necessary Lubricate these parts at lease once every month 5 Check hydraulic reservoir once every week With all hydraulic cylinders retracted the oil level should be approximatel
21. y have to assist the bead opposite the tool into the drop cen ter Use one of the tire tools to pry the top bead into the drop center 6 Rotate the wheel counterclockwise while main taining pressure on the bead lifting tool until the first bead is off 7 Repeat the steps above for the rear bead 8 Retract the tool and remove the tire Mounting 1 LUBE BOTH BEADS LIBERALLY 2 Roll the tire onto the camage and lean it back against the rim 4 COATS H I T 5000H Changer 3 Position the combo tool near the edge of the rim as shown DO NOT CONTACTTHE RIM s gt gt AFT sv pl mm AT y viet A a F r ta s a de e i FR Sn A i A 5 e 4 Securely clamp the vise grip to the rim edge at a position to the left of the combo tool Rotate the chuck clockwise until the vise grip hooks the inner bead and lifts the tire 5 Continue rotating the chuck until the first bead is mounted Avoid rotating the vise grip into the combo tool 6 Remove the vise grip and repeat the steps above to mount the outer bead A CAUTION When mounting a tire the bead must be started in the drop center of the rim Failure to use the drop center could result in dam age to the tire bead Note It may be necessary to push the bead s into the drop center during the mounting process Note Tire lubricant greatly reduces the force needed to demount or mount a tire Liberally lube each bead and rim edge while
22. y two inches below the top of reservoir Add COATS hydraulic oil PN 120454 to this level 6 Change the oil filter once every six months Screw off the filter and replace with service part number 001631 14 COATS H I T 5000H Changer Notes COATS H I T 5000H Changer 15 Notes 16 COATS H I T 5000H Changer Notes COATS H I T 5000H Changer 17 Truck Tire Changer Warranty Policy The COATS Company warrants the H I T 5000H Truck Tire Changer to be free of defects in workmanship and matenal for a period of twelve 12 months from the date of installation Labor will be covered by the COATS Company for a period of 90 days from the date of installation Upon inspection by COATS Company or its authorized representative any defect in workmanship and or mate rial within the warranty period will be Replaced in the field by the user parts supplied free of charge by the COATS Company LaVergne Tennessee for the first 12 months of operation Labor is covered by the COATS Company for the first 90 days of operation This warranty is in lieu of all other warranties expressed or implied and of all other obligations and or liabilities and no person is authorized to make any other representation or assume any other obligation on behalf of the manufacturer This warranty shall not apply if damage is due to accident negligence alteration abuse or misuse wom parts installation by unlicensed electrician or has not been operated
Download Pdf Manuals
Related Search