SEDEO PRO - Handicare
Contents
1. USER MANUAL CANADA SEDEO PRO a gt 7 A A a Aa gt A 7 _ Ap a f d me ee 7 P pe Yf 3 f 3 J LAT amp handicare 1011651D CE Sedeo Pro 2011 Handicare All rights reserved The information provided herein may not be reproduced and or published in any form by print photoprint microfilm or any other means whatsoever electronically or mechanically without the prior written authorization of Handicare The information provided is based on general data concerning the construction known at the time of the publication of this manual Handicare executes a policy of continuous improvement and reserves the right to changes and modifications The information provided is valid for the product in its standard version Handicare can therefore not be held liable for any damage resulting from specifications of the product deviating from the standard configuration Illustrations contained in the manual may deviate from the configuration of your product The information made available has been prepared with all possible diligence but Handicare cannot be held liable for any errors contained in the information or the consequences thereof Handicare accepts no liability for loss resulting from work executed by third parties Names trade names trademarks etc used by Handicare may not as per the legislation concerning the protection of2. 5 16 Thigh support Adjust the thigh support as follows 1 Loosen the Torx screw 2 Adjust the part to the desired position 3 Tighten the Torx screw A a Depth adjustment B b Width adjustment A a Height adjustment B b Memory setting adjustment Cie Bracket position adjustment D d Cushion position adjustment Tip The height adjustment can be fixed using the memory setting 5 17 Attaching the lap strap Attaching to the slider 1 Loosen 2x A and remove A from the left hand and right hand sliders 2 Place B in the sliders and tighten in the desired position 3 Position 2 x A back in the sliders and tighten A Sedeo i 59 Sedeo i 62 Seating system adjustments to be carried out by a professional 59 Attaching to the seating frame 1 Attach A to the seating frame using a screw on the left and on the right Sedeo i 63 Warning Ensure that the lap strap is adjusted to the wheelchair user The strap must fit snugly across the hips at an angle of approximately 45 Ensure that the strap is clean at all times and that the locking mechanism is working properly The strap and the locking mechanism can be cleaned using a damp cloth If the strap is positioned above the hips and across the soft part of the user s belly then this can result in seating posture being incorrect and the user slumping in the seat Never use the lap strap a
3. Ensure that C and D at the back of the seat hook under the bolt heaas A Sedeo i 7 46 Seating system adjustments to be carried out by a professional 5 Seating system adjustments to be carried out by a professional Note There are calibration marks on various parts of the seating system The ex factory settings are indicated 5 1 Seat depth Backrest adjustment 1 Loosen A by one turn 2 Adjust B to the desired position 3 Tighten A Seating system adjustment 1 Remove the seat see Use Reducing the seating system in size for transportation purposes Remove the screws B Move C and D Tighten the screws B Replace the seat see Use Setting up the seating system following transportation PN 5 2 Seat width 1 Loosen A by one turn 2 Slide B into the desired position 3 Tighten A A L R afe afc Sedeo i 49 Pa Sedeo i 52 Seating system adjustments to be carried out by a professional 47 5 3 Backrest angle 1 Turn A in order to adjust B Sedeo i 9 5 4 Backrest height 1 Loosen A by one turn 2 Adjust B to the desired position 3 Tighten A 5 5 Standard and manually elevating legrest Legrest width 1 Loosen A by one turn 2 Sli
4. Lor ejg Tighten by one turn with wing nut Loosen by one turn with torx Tighten by one turn with torx a fille Step 1 2 etc An arrow as part of an illustration indicates that the component in question moves or needs to be moved in the direction indicated Notes on Key to symbols Each illustration includes icons and numbering to indicate what needs to be done and in which order Tools supplied A T30 Torx key is supplied with the seating system This can be used by a professional for adjusting all of the seating system settings The T30 Torx key A can be found on the frame at the location indicated in the illustration edeo 1 Note There are calibration marks on various parts of the seating system The ex factory settings are indicated 36 Use 4 Use 4 1 Adjustment of the seating system by the user attendant Manually recling backrest by attendant 1 Squeeze A 2 Adjust B to the desired position Note Keep squeezing A 3 Release A Manually recling backrest by user 1 Squeeze A 2 Lean forwards or backwards to adjust B to the desired position C Sedeo g 1 Note Keep squeezing A 3 Release A Power reclining backrest Power reclining backrest is adjusted by moving the electronic joystick Please refer to the controller owners manual for operating instructions Sedeo
5. 8 1 CE declaration of conformity C The product is in conformity with the provisions of the Medical Devices Directive and carries the CE mark The product also meets the following requirements and standards This has been verified by independent test organizations 1 EN 12183 2009 Manual wheelchairs or EN 12184 2009 Electrically powered wheelchairs ISO 7176 19 Crash test PO Gi Goons cigarete match flame equivalent 8 2 Technical information ISO 7176 8 Requirements for impact static and fatigue strength ISO 7176 9 Climatic tests for electric wheelchairs and scooters ISO 7176 16 Requirements for resistance to ignition of upholstered parts EN ISO 10993 5 1999 11 Biological evaluation of medical devices EN 1021 1 2 Assessment of the ignitability of upholstered furniture Ignition source smouldering Seating system User Weight 160 kg Seat width 400 540 mm option 520 680 mm Seat depth 420 600 mm Point of gravity 95 mm Seat Seat cushion depth position 20 mm 0 20mm Backrest Backrest height 500 640 mm Backrest angle 89 128 Backrest recline option 89 128 Armrest Armrest pad width 20 0 mm per side Armrest pad height 170 290 mm option 270 390 mm Armrest depth 80 mm Armrest pad depth controller bracket side 50 mm non controller bracket side 160 mm Side support Side cu
6. manual is a supplement to Handicare s general wheelchair user manual Where necessary this user manual refers to other manuals as shown below Wheelchair Refers to the general wheelchair user manual CI Controller Refers to the user manual for the controller only applicable for power wheelchairs Read this user manual and the other user manuals referred to carefully before using the product If one of the user manuals was not included with your wheelchair please contact your dealer immediately In addition to this user manual there is also a service manual for qualified specialists CONTACT HANDICARE IF YOU HAVE A VISUAL IMPAIRMENT 1 2 Symbols used in this manual Note Pointing out possible problems to the user A Caution Advice for the user to prevent damage to the product A Warning Warnings for the user to prevent personal in jury Not following these instructions may result in physical injury damage to the product or damage to the environment 34 Safety 2 Safety Warning Always follow the instructions given next to the warning symbols Failure to follow these instructions may result in physical injury damage to the wheelchair or damage to the environment Where possible the warning symbols have been placed in the applicable paragraphs Be carefull when swing away flip up parts Contact with moving parts should be avoided Caution Parts of the wheelch
7. and liability applicable to the seating system are identical to those incorporated in the wheelchair manual Wheelchair 65 66 67 Ay handicare Handicare B V Vossenheemd 104 5705 CL Heimond The Netherlands T 31 0 492 593 888 F431 0492 537 931 Serienummer www handicare cam
8. fully forward Note If necessary first remove the back cushion and or the armrest assemblies Sedeo g 20 44 Use Removing Sedeo footrests legrests The following steps apply to Sedeo swingaway footrests manual elevating legrests and power elevating legrests 1 Remove the velcro calf strap from one side of the footrests if calf strap is installed 2 Push the catch A to the rear in order to unlock the leg rest 3 Swing the leg rest outwards 4 Remove the leg rest B from its bracket by lifting You should hear a click when replacing the leg rest This indicates that the leg rest has locked into place Removing the armrest assembly 1 Tip A downwards 2 Remove B 4 6 Setting up the seating system following transportation Positioning the armrest assembly 1 Slide A onto B 2 Push C upwards Use 45 Positioning the backrest for use 1 Fold A upwards and backwards 2 Tighten B Sedeo g 23 Positioning the back cushion 1 Hook A behind B 2 Turn C A Caution Ensure that the back cushion is firmly in position handles upwards o 7 i a EH Sedeo g 24 Positioning the seat 1 Slide A and B over C and D 2 Push E downwards A Caution
9. into the desired position 3 Tighten A lt Sedeo i 44 DN Sedeo i 45 56 Seating system adjustments to be carried out by a professional Height 2 1 Loosen C by one turn 2 Slide D into the desired position 3 Tighten C Sedeo i 47 5 13 Abduction support Adjust the abduction support as follows 1 Loosen the Torx screw 2 Adjust the part to the desired position 3 Tighten the Torx screw A a Height adjustment B b Depth adjustment _ Sedeo i 53 5 14 Backrest with adjustable straps flexible The sides of the backrest with adjustable straps can be adjusted as follows 1 Loosen the four Torx screws 2 Adjust the sides to the desired position 3 Tighten the four Torx screws A a Angle adjustment Seating system adjustments to be carried out by a professional 57 5 15 Thoracic support Adjust the thoracic support as follows 1 Loosen the Torx screw 2 Adjust the part to the desired position 3 Tighten the Torx screw A a B b A a B b A a B b Rough adjustment of width Height adjustment Adjustment of bracket depth Adjustment of cushion depth Adjustment of cushion angle Fine adjustment of width Sedeo i 55 Sedeo i 56 Sedeo i 57 58 Seating system adjustments to be carried out by a professional
10. the locked position and twist B into the desired position Sedeo g 29 Note Ensure that B is properly secured Use 39 4 2 Getting into and out of the wheelchair forward transfer Warning Do not stand on the footplates Putting your full weight on the footplates may lead to wheelchair damage and to hazardous situations including the wheelchair tipping up Sedeo Original standard legrest 1 Fold up the foot supports 2 Swing the calf plates to the side if applicable 3 If possible swing the legrests to the side 4 Seat yourself in the chair Flipping up the central legrest footplate 1 Flip up A 4 3 Getting into and out of the wheelchair sideways transfer Sedeo g 14 Note Some versions of the controller will need to be swung aside Removing the armrest assembly 1 Tip A downwards 2 Remove B Sedeo g 15 40 Use Folding back the armrest assembly 1 Press A 2 Fold B to the rear Caution Remove the tray before folding back the armrest assembly Warning Do not lean on the armrest when folded back 4 4 Options accessories Removing positioning the headrest 1 Lift A 2 Slide B out of or into C 3 Push A down Note Always slide the headrest until it comes to a stop in the bracket Flip down the abduction support 1 Pull A out of the
11. trade names be considered as being available 2011 01 32 Introduction 1 1 This manual 1 2 Symbols used in this manual Safety 2 1 Temperature 2 2 Indications on the seating system General description 3 1 Sedeo Pro product description se 1 Adjustment of the seating system by the user attendant 2 Getting into and out of the wheelchair forward transfer 3 Getting into and out of the wheelchair sideways transfer 4 Options accessories 5 Reducing the seating system in size for transportation purposes 6 Setting up the seating system following transportation Use 4 4 4 4 4 4 Seating system adjustments to be carried out by a professional 5 1 Seat depth 5 2 Seat width 5 3 Backrest angle 5 4 Backrest height 5 5 Standard and manually elevating legrest 5 6 Comfort legrest 5 7 Central legrest 5 8 Central legrest gas spring adjustment 5 9 Armrest assembly 5 10 Adjusting the centre of gravity 5 11 Headrest 5 12 Fixed swing away controller bracket 5 13 Abduction support 5 14 Backrest with adjustable straps flexible 5 15 Thoracic support 5 16 Thigh support 5 17 Attaching the lap strap Maintenance 6 1 Cleaning the upholstery Troubleshooting Specifications 8 1 CE declaration of conformity 8 2 Technical information Provisions of warranty Introduction 33 1 Introduction 1 1 This manual This user manual will help you to use and maintain your seating system safely This user
12. Original comfort legrests knee angle The angle of the comfort leg rests can be adjusted independently of each other 1 Push handle B forwards 2 Lift your leg 3 Release the handle when in the desired position Sedeo power elevating legrests Knee angle is adjusted by moving the electronic joystick Please refer to the controller owners manual for operation instructions Use 37 Sedeo Original central leg rest gas spring adjustment knee angle 1 Press gas spring handle C 2 Adjust the leg rest to the desired position 3 Release the gas spring C C B Moving the controller bracket inwards 1 Push A inwards until hearing a click aj Sedeo g 5 Swing away the controller bracket 1 Push A outwards until hearing a click Note Swinging back the controller bracket will allow you to pull up close to a table Full operation of the controller remains possible 38 Use Push handle height 1 Loosen A by one turn 2 Slide B into the desired position 3 Tighten A Angle adjustable push bar 1 Loosen A by one turn 2 Slide B into the desired position 3 Tighten A Warning Do not use the push bar to tip the whole chair to the rear in order to mount a pavement for example The push bar is not suitable for such use Hemiplegia armrest 1 Pull A out of
13. air that are intended for service or repair to be removed without the use of tools e g armrest legrest can have an adverse effect on the support of the user if they are missing or not placed back in the right position 2 1 Temperature Warning Avoid exposing the wheelchair to direct sunlight for extended periods of time Some parts of the wheelchair such as the seat the backrest and the armrests assembly complete can become hot if exposed to the sun for too long This may cause burns or skin irritation 2 2 Indications on the seating system i The wheelchair must not be lifted up by the armrests assembly O ol complete and or legrests seating system s centre of gravity Such adjustments should be made by professionals only A The stability of the wheelchair is influenced by the adjustment of the General description 35 3 General description 3 1 Sedeo Pro product description The wheelchair is fitted with a Sedeo Pro seating system The Sedeo Pro seating system provides excellent support for the head torso arms and legs Optimal body support ensures maximum independence for the wheelchair user The wheelchair must be adjusted by a qualified specialist Incorrect settings may have negative consequences for seating posture Caution Please study this manual carefully before using the seating system Key to symbols Loosen by one turn with wing nut
14. de B into the desired position 3 Tighten A Sedeo i 11 48 Seating system adjustments to be carried out by a professional Lower leg length 1 Loosen the setscrew A a few turns with a 4 mm Allen key 2 Slide the footplate B in the desired position 3 Tighten the setscrew A securely Caution Ensure that there is sufficient free space under B for the wheelchair to drive over obstacles Footplate angle 1 Loosen the Allen bolt C a few turns with a 6 mm Allen key so that the teeth of the hinge come completely free 2 Adjust the desired footplate angle D and push the hinge manually together again 3 Tighten the Allen bolt C securely Footplate depth The footplate is secured asymmetrically The left and right footplate can be exchanged 1 Loosen the setscrew A with a 4 mm Allen key 2 Remove the footplate together with the profile 3 Slide the footplate in the top tube of the other legrest 4 Tighten the setscrew A securely Caution Make sure that the castor wheels do not touch the footplates when manoeuvring If this is the case the legrests must be brought forward There must be at least 1 cm between the castor wheels and the footplates 5 6 Comfort legrest Calf pad height 1 Loosen the Allen bolt A a few turns with a 4 mm Allen key 2 Slide the calf pad B in the desired position 3 Tighten the Allen bolt A secure
15. djusting the centre of gravity A Warning The stability of the wheelchair is influenced by the adjustment of the seating system s centre of gravity Such adjustments should be made by professionals only 1 Loosen A by one turn 2 Slide B forwards or backwards 3 Tighten A Note If the user s weight distribution is average then the centre of gravity should be adjusted to the same setting as the seat depth Sedeo i 40 For better sliding release the seat depth adjustment 54 Seating system adjustments to be carried out by a professional 5 11 Headrest Headrest height 1 Lift A 2 Slide B into the desired position 3 Push A down Adjusting the memory setting 1 Loosen C by one turn 2 Slide D as far down as possible 3 Tighten C Sedeo i 42 Headrest position 1 Loosen A by one turn 2 Adjust B to the desired position 3 Tighten A Note Correct the headrest height and tilt the headrest cushion as required Sedeo i 43 Seating system adjustments to be carried out by a professional 55 Headrest cushion width 1 Loosen A by one turn 2 Slide B into the desired position 3 Tighten A 5 12 Fixed swing away controller bracket Depth 1 Loosen A by one turn 2 Slide B into the desired position 3 Tighten A Height 1 1 Loosen A by one turn 2 Slide B
16. locked position and flip down B 2 Release A Flip up the abduction support 3 Pull A out of the locked position and flip up B 4 Release A in the locked position Note Ensure that B is properly secured Sedeo g 17 _ Sedeo g 31 Use 41 Folding back the thoracic support 1 Press A to fold back B Removing the thigh support 1 Loosen A by one turn 2 Remove B 42 Use Sedeo g 25 4 5 Reducing the seating system in size for transportation purposes A Warning A Seat 2 5 kg The wheelchair can be reduced in size for B Backrest 2 5 kg transportation without a passenger Any C Armrest assembly 2 kg components of the seating system that can be D Legrest 1 7 kg detached easily should be removed Store away E Headrest 1 3 kg such components safely so that they can not cause injury or damage or become damaged themselves Use 43 Removing the seat 1 Pull A upwards and forwards Removing the back cushion 1 Turn A and B 2 From the bottom pull C forwards and upwards and remove Folding the backrest fully forward 1 Loosen A Sedeo i 4 s Z Sedeo g 19 Note Do not remove A 2 Fold B
17. ly Seating system adjustments to be carried out by a professional 49 5 7 Central legrest Lower leg length 1 Loosen A by one turn 2 Slide B into the desired position 3 Tighten A Caution Ensure that there is sufficient free space under B for E 4 8 the wheelchair to drive over obstacles I E E Sedeo i 19 Knee angle 1 Loosen A by two turns 2 Adjust B to the desired angle 3 Tighten A by two turns Caution Change the height or knee angle if the footplate touches the castor wheels Sedeo i 20 Ankle angle 1 Flipup A 2 Turn B in order to adjust the ankle angle as desired 3 Fold A down 8 Sedeo i 21 50 Seating system adjustments to be carried out by a professional Calf pad height 1 Loosen A by one turn 2 Slide B into the desired position 3 Tighten A 5 8 Central legrest gas spring adjustment Lower leg length 1 Loosen the knob B 2 Slide the footplate A in the desired position 3 Tighten the knob B securely lt Sedeo i 22 Note Make sure that there is sufficient free space under the footplate to operate the wheelchair over obstacles 5 9 Armrest assembly Armrest height 1 Loosen A by one turn 2 Adjust B
18. s a seatbelt when using transport Sedeo i 64 Sedeo i 65 60 Maintenance 6 Maintenance It is recommended that you have your wheelchair serviced by your dealer once a year or in the case of intensive use once every six months 6 1 Cleaning the upholstery Clean the upholstery using a damp cloth and household soap Then rub dry using a soft dry cloth PU parts Clean the armrests side cushions etc using a damp cloth and household soap Then dry the parts using a soft cloth Seat and backrest cushion upholstery Follow the washing instructions on the covers For the incontinence cover see figure 1 For the comfort cover see figure 2 Warning Do not use organic solvents such as thinner benzine or white spirit Do not chemically clean the upholstery Do not iron or spin dry the upholstery Stretch Rubber 58 Knitted Polyester 42 FR Polyurethane Fabric Backing 100 Polyester Coating 100 PVC Care instructions Do not use cleaning materials that contain solvents 9005849 Yo handicare Figure 1 Stretch Fabric 35 Polyester 65 Dioleen Safe Fabric Backing 100 Polyester Coating 100 PVC Care instructions Do not use cleaning materials that contain solvents 9005850 NG handicare Figure 2 Troubleshooting 61 7 Troubleshooting If there is a problem with your seating system contact you dealer 62 Specifications 8 Specifications
19. shion height 65 mm Central legrest Lower leg length 350 515 mm Knee angle 30 110 Ankle angle 20 till 40 Central calf support height option 120 mm Specifications 63 Manually elevating central legrest Lower leg length 430 550 mm Knee angle 35 95 Standard legrest set Lower leg length 360 530 mm Knee angle 70 Ankle angle 0 180 Elevating and electrical elevating legrest set Lower leg length 360 540 mm Knee angle 70 0 Ankle angle 0 180 Calf support height 120 mm Headrest Headrest height memory 170 mm Headrest depth 180 mm Headrest vertical angle 45 45 Headrest width option standard head rest 20 20 mm width adjustable head rest 110 110 mm Controller bracket Controller bracket height 60 mm Controller bracket depth 35 mm Controller bracket swing away Controller bracket height 50 mm Controller bracket depth 35 mm Controller position angle 0 45 Pushbar Pushbar height 185 mm Hemiplegia Hemiplegia armrest angle option 0 45 Abduction support Abduction support height 60 120 mm Abduction support depth 60 110 mm Thoracic support Thoracic support width 60 0 mm Thoracic support height 200 400 mm Thoracic support depth 20 70 mm 64 Provisions of warranty 9 Provisions of warranty The provisions of warranty
20. to the desired position 3 Tighten A Note Ensure that the arms are supported well without the shoulders being pushed upwards a Sedeo i 23 Seating system adjustments to be carried out by a professional 51 Armrest depth 1 Loosen A by one turn 2 Slide B into the desired position 3 Tighten A Note Position the armrest further back in order to obtain more space for transfers Sedeo i 24 Armrest depth 1 Loosen A by one turn 2 Slide B into the desired position 3 Tighten A Sedeo i 25 Armrest width with or without controller bracket To remove 1 Loosen A 2 Remove B Sedeo i 31 52 Seating system adjustments to be carried out by a professional 3 If applicable loosen C by one turn 4 Remove D if applicable 5 Loosen E by one turn 6 Remove F To position 1 Slide A together with B or C onto D Note Ensure that the ridge on the terminal block falls into the opening lt Sedeo i 33 53 Seating system adjustments to be carried out by a professional 2 Adjust the depth of A and tighten E 3 Position the controller bracket 4 Position the armrest Side panel height 1 Loosen A by one turn 2 Adjust B to the desired position 3 Tighten A Sedeo i 39 5 10 A
Download Pdf Manuals
Related Search