Pannier Mount Set (Triumph Tiger 800 91M-TR01)(11
Contents
1. 6mm bolts 2 with a 8mm socket tool Move to STEP 2 STEP 2 Use a pick or similar tool to carefully remove the four plastic caps 3 that protect the 6mm accessory mount holes 4 on the underside of the sub frame REMINDER Save all of the removed hardware so you can return the motorcycle to its original configuration if you decide to remove the pannier mounts Move to STEP 3 The images in this instruction set may be different than your accessory or motorcycle 91M TRO1 R1 04 04 2014 11 400311 INSTALLATION INSTRUCTIONS continued STEP 3 Some of the motorcycle s hardware will be reused when installing the pannier mounts The four 8mm flange style lock nuts 1 will be reused keep them handy as you remove hardware The two 8 x 65mm bolts 2 that secure the front arm of the grab rail to the motorcycle will also be reused Remove this hardware from the motorcycle NOTE This image shows hardware on the right side of the motorcycle When fol lowing the installation instructions apply the procedures to the opposite side of the motorcycle unless promoted to do otherwise Move to STEP 4 STEP 4 With the aid of an helper hold the right pannier mount 3 up to the motorcycle CAUTION Use care when maneuvering the right pannier mount into place so you do not scratch the exhaust silencer Use some protective tape to protect the exhaust s surface but do not forget to remove it before starting the engine again Route one of2. discs 3 dia Right hand pannier mount Mounting lip Washers 1 5 dia Back bar Mounting lip buffer strips Washers 1 25 dia Spacer 8mm ID x 1 2 L Button head bolt 6 x 16mm Rubber washer 1 5 dia Flange bolt 8 x 75mm Nylock flange nut 6mm Instruction sheet not shown Hex bolt 6 x 20mm Flange bolt 8 x 30mm Washer 6mm ID Nylock flange nut 8mm Buttonhead Allen bolt 6 x 25mm Nylock nut 6mm F fo tO T 10 to 092000 Appearance and scale of sample image may differ from actual supplied parts INSTALLATION INSTRUCTIONS Your MOOSE pannier mounts were developed to mount easily to Triumph Tiger 800 motor cycles in stock trim Before beginning have your motorcycle s Owner s Manual and Service Manual handy in case you need to reference a procedure WARNING Place the motorcycle on it s center stand or a secure service stand so it will not tip over and injure you or cause damage to the vehicle itself Perform the work on a cool motorcycle to prevent burns Enlist the aid of a helper when install ing the mounts on your motorcycle as some steps require holding components while a fastener is being installed If you lack the technical understanding or ability to install the pannier mounts seek out the assistance of a qualified motorcycle technician STEP 1 Remove the seats refer to the procedure in your owner s manual Remove the plastic tail cover 1 by removing the four
3. safety reflectors are visible once the mounts and panniers are in place If the panniers of the mounts block any side reflectors place reflectors on the exterior sides of the panniers reflectors with self adhesive backing are available from motorcycle or automobile supply stores After 50 miles 80 kilometers of riding recheck the panniers and mounts to make sure that they are still tight and secure Inspect the accessories more often if you are riding your motorcycle in wet or rough conditions such as a dirt road Inspect the accessory and related hardware before and during each ride Loose accessory and or mounting hardware can interfere with the vehicle s operation and cause an unsafe riding condition CARE OF YOUR MOOSE EXPEDITION PANNIER MOUNTS Check the attachment and assembly hardware often tighten these fasteners as recommended in this instruction set and as listed in your vehicle s owner s manual Your MOOSE mounts require almost no cosmetic maintenance other than periodic cleaning with mild soap and water It is normal for some scuffing of the mounts finish to occur especially if you operate your motorcycle in dusty wet or dirty conditions This type of wear is normal and is not considered a defect so repair or replacement of parts due to this type of surface wear is not covered under the product s limited warranty You can use paint to cover such wear so the metal does not rust or corrode MOOSE LIMITED ONE YEAR WARRANTY M
4. the 8 x 65mm flange bolts removed in STEP 3 4 through the rear mount tab through the supplied 1 2 L spacer and into the rear mount hole in the sub frame Make sure the original buffer plate is still in place between the spacer and the motorcycle s plastic bodywork Hand thread one of the saved 8mm flange nuts onto the other end of the bolt but do not tighten it fully yet Repeat the process on the other side of the motorcycle WARNING Always apply a thread locking agent to the threads of the bolts and nuts as you install the hardware Do this to the new hardware and original fasteners you reinstall as part of the mount installation procedure See page 8 of this instruction set for the type of recommended thread locking agent CAUTION Do not tighten any mounting hardware fully until all of the mount set com ponents are loosely assembled together on the motorcycle This will ensure all of the components mesh together and further permits you to make aesthetic adjustments Move to STEP 5 STEP 5 Route one of the supplied 8 x 75mm flange bolts 7 through the mount s front tab through the supplied 1 2 L spacer 8 and then through the grab rail and into the sub frame Hand thread one of the saved 8mm flange nuts onto the other end of the bolt but do not tighten it fully yet Repeat the process on the other side of the motorcycle Move to STEP 6 STEP 6 Route the supplied 6 x 20mm hex bolts 49 and 6mm ID flat washers
5. the proper size drill bit carefully drill each of the required holes REMINDER Refer to the drill bit hole size list on page 4 STEP 8 of this instruction set Move to STEP 14 STEP 14 Hand turn a large drill bit 1 2 or use a formal deburring tool to remove any burrs or loose material from the drilled holes CAUTION Deburr the exterior of the holes and the inside of the holes Use a shop vacuum to clean up the drilling debris from the inside of the pannier Take care to keep your work area clean of aluminum chips or other debris that could damage the pannier s finish After the holes are deburred and the debris cleaned off the pannier re tape the buffer template back into place Move to STEP 15 The images in this instruction set may be different than your accessory or motorcycle 91M TRO1 R1 04 04 2014 11 400311 STEP 15 Prep the two mounting lips included with your pannier mounts by installing the 1 8 thick buffer strips on each lip as show 4 Once you peel the protective backing off carefully place the strips on each lip and press firmly so they will stick in place TIP You may need to trim the supplied buffer strips so verify the length before removing the protective backing from the strip The majority of the water resistance designed into your pannier mounting compo nents is from the plastic buffer drill template and the Nylock style nuts that hold the mounting lip in place on each pannie
6. 41 through the lower mount plates 4 and into the sub frame Repeat on both sides of the motorcycle Do not fully tighten the hardware yet Move to STEP 7 The images in this instruction set may be different than your accessory or motorcycle 91M TRO1 R1 04 04 2014 11 400311 STEP 7 With the left and right side mounts loosely in place install the back support bar Position the bar 1 under the rear fender and rotate the tube so its holes align with the holes in the nipples welded to the hoop section of the mounts 2 Use the supplied 6 x 25mm button head Allen bolts 3 and 6mm locking nuts 4 to connect the bar to the mounts Orient the bar s hardware so the bolt head faces outward Prepare to tighten ALL of the hardware fully IMPORTANT ASSEMBLY NOTE Verify that all of the mounting hardware is installed on the mounts and the motorcycle s chassis Make sure all of the fasteners are threaded properly into their respective nuts or mounting points and thread lock has been applied Check to make sure the mounts are aligned properly on the motorcycle and then begin to tighten all of the hardware to the torque specifica tions listed in the Hardware Torque Value table on page 8 of this instruction set With the mounts securely installed on the motorcycle reinstall the plastic tail cover and the seats removed in STEP 1 You will now need to prepare your panniers for attachment to the mounts Move to STEP 8 STEP 8 Supplied wi
7. MOOSE EXPEDITION LUGGAGE ADVENTURE PANNIER MOUNT SET INCLUDES EVERYTHING YOU NEED TO ADD MOUNTS TO YOUR MOTORCYCLE 3501 0917 Triumph Tiger 800 2011 2014 FEATURES OF THE EXPEDITION LUGGAGE ADVENTURE PANNIER Mount SET Rugged 18mm steel tube mounting hoops and arms rigidity secure the luggage to your motorcycle Precision machined brackets ensure proper fit and durability Deep complete welds make sure the mounts can handle the rigors of Adventure Touring Thick black matte powder coating looks as good as it is tough Includes high quality cad plated hardware with flange style bolt heads and flange style locking nuts Designed to work perfectly with MOOSE Expedition Aluminum Panniers No motorcycle modification required simple installation Designed and built in the U S A READ THESE INSTRUCTIONS THOROUGHLY BEFORE INSTALLATION Because of the variety of motorcycle configurations other accessories and the features and intended use of this MOOSE accessory there are many different mounting options You are responsible for the proper installation of this accessory on your motorcycle Download the required instructions for your accessory mount set and motorcycle from www MOOSERACING com Your attention to the installation instructions and recommendations will permit safe and proper use of this accessory You must mount this accessory properly and securely before riding your motorcycle If you lack the ability to safely and properly install th
8. ead Lock obtain TB 1303 or an equivalent from your MOOSE dealer Round out your Adventure luggage with a MOOSE Top Case and Mounts See your PARTS UNLIMITED dealer or check out the products on www mooseracing com MAXIMUM LOAD CAPACITY 25 Ibs 11 33 kg per mount side pannier While your pannier mount set has been designed to tolerate the rigors of touring use care must be taken to not overload your luggage system and your vehicle Include the weight of the mounts and panniers when calculating the amount of cargo you will be carrying on your motorcycle Do not exceed your vehicle s Maximum Gross Vehicle Weight as listed on your motorcycle or in its Owner s Manual IMPORTANT Failure to install this accessory properly may allow portions of the mounts mounting hardware or panniers to come into contact with the motorcycles s moving parts or controls It is vital that you verify that neither the accessory nor any of its parts can touch or interfere with other motorcycle components while the steering or suspension moves through its entire range of motion Make sure that neither your panniers their mounts or any related hardware can come into contact with the exhaust or any other component of the motorcycle as other vehicle components may be damaged by contact with this accessory It is your responsibility to make sure the installation of this accessory does not create an unsafe or illegal condition Check to be sure that all lights and
9. efer to the table on page 8 for final torque specification Move to STEP 19 STEP 19 OPTIONAL ITEMS AVAILABLE You can obtain a pannier attachment kit which includes hardware that permits pannier removal and installation without tools See your MOOSE dealer for more information CAUTION When riding over rough paved roads or unimproved terrain or with a heavy cargo load you should always use the supplied standard mounting bolts and locking nuts This hardware will properly secure your panniers to the mounts Move to STEP 20 STEP 20 pan j z UN Visually inspect the panniers to verify they are mounted evenly and away from any other Wj gt components on the motorcycle Before riding do a complete review of the installation Do smp elie not load the panniers with cargo during an initial test ride Install the pannier lids andlatch Te S them securely After your test ride double check the installation A mrt EAA WARNING Review all of the information on page 8 of the instruction set It is im perative that you continually verify the security and integrity of your accessory and its mounting on your motorcycle Adventure and Dual Sport motorcycles are very capable vehicles and they can operate in environments that will tax any me chanical device Your safety and that of others is dependent on your attention to this continual inspection of your vehicle and it s accessories The images in this instruction set ma
10. erstand any part of the accessory mounting system e You have any doubts as to the security of the mounting system If you have any concerns or questions contact your authorized MOOSE retailer Remember Motorcycling can be a dangerous activity Installation of any accessory can increase your risk if it is not installed properly You are responsible to install this accessory so it will not contact any portion of the drive train suspension or steering and so that it will in no way interfere with the operation of your motorcycle RECOMMENDED TooLs amp MATERIALS 12mm wrench or socket may need two 13mm wrench or socket may need two 10mm wrench or socket may need two 8mm wrench or socket may need two 3 Phillips screwdriver Power drill up to 1 2 chuck 5 16 amp 1 4 drill bits Center punch Deburring tool or 1 2 drill bit Masking tape amp pen Shop vacuum Required Vinyl electrical tape Required Thread Locking Agent Suggested Double sided adhesive tape NOTE Other tools may be required depending upon your vehicle previously installed accessories and how you will mount this accessory Continued on next page The images in this instruction set may be different than your accessory or motorcycle 91M TRO1 R1 04 04 2014 11 400311 I TEMS INCLUDED WITH YOUR EXPEDITION PANNIER Mounts Mount parts Qty Pannier attachment hardware i Pannier attachment hardware Left hand pannier mount Buffer drill templates Support
11. is accessory seek out a qualified motorcycle technician for assistance During installation support the motorcycle with a suitable stand or lift so it will not tip over and injure you or damage the vehicle Using or mounting this accessory improperly could result in a loss of control of the motorcycle which could result in damage to your motorcycle or other personal property the property of third parties and or personal injury to yourself or others up to and including death BE SURE TO THOROUGHLY READ AND CLOSELY FOLLOW THE MOUNTING INSTRUCTIONS THAT ARE INCLUDED WITH THIS ACCESSORY e The pannier mounts must be installed and securely fastened to the motorcycle s frame e Install the mounts securely so they will not shift or move while riding Make sure the mounts and all related brackets and hardware will not contact the wheels suspension or any other moving parts of the motorcycle If you do not understand these instructions DO NOT install the mounts Remove any components you may have already installed on your motorcycle Thoroughly inspect your motorcycle s luggage mounts and panniers before every ride Do not use the panniers if the mounts have been modified or if they have deteriorated loosened cracked or are beginning to fail in any way Do not use the panniers or mounts if your motorcycle s frame is damaged or if the sub frame is damaged or is loose on the main chassis Check the security of the mounts at each stop as you ride Mounti
12. mount assembly via the bottom mounting lip and the hardware that connects it to the brackets in the top corners of the mount s rectan gular hoop Familiarize yourself with the hardware and lay it out in the order that is used to attach the pannier to the mount Item Description Qty per pannier 1 Flange bolt 8 x 30mm 2 2 Washer 1 5 dia 2 3 Rubber washer 1 5 dia 2 4 Support disc 3 dia 2 5 Pannier protector 6 Mount bracket T Washer 1 25 dia 2 Nylock flange nut 8mm 2 TIPS Enlist the aid of another person when mounting the panniers Once you are familiar with the mounting process you can easily do it by yourself Pre install the washers in the proper order that go on the flange bolts before attempting to mount the pannier With the lid off of the pannier carefully lift it up and position it so the mounting lip slips over the bottom porting of the mount s rectangular hoop Adjust the pannier s position so you can insert the bolt through the washers then through the hole in the pannier s wall and the mount bracket Slip the washer onto the protruding end of the bolt and hand thread the Nylock nut onto the bolt Hand install the hardware in the other corner of the pannier mount Using the proper wrench and or socket tighten both bolts 2 and nuts 8 in each pan nier Repeat for the other pannier CAUTION Tighten all of the hardware evenly After the initial tightening of the hard ware r
13. ng hardware can loosen during operation so be sure to check it frequently Do not use this accessory mount set if you have any doubts as to whether it is properly mounted to your motorcycle Do not exceed 25 pounds of cargo in each pannier bag you attach to your mounts 50 pounds total When using this accessory do not exceed your vehicle s Maximum Gross Vehicle Weight as listed on your motorcycle or in its Owner s Manual Be aware the panniers and cargo will affect your vehicle s performance and handling characteristics Use caution when riding your motorcycle Balance your cargo evenly between each pannier and arrange its placement so it does not shift during riding When riding with panniers mounted to your motorcycle be aware the width of your luggage may exceed the width of your handlebars Use extra care when maneuvering in traffic or around other obstacles so you do not impact other objects with your luggage If you strike another object or tip over your motorcycle immediately inspect the panniers their mounts and your vehicle for damage If your panniers or mounts are ever damaged do not use them until they have been inspected by your local professional motorcycle dealer Replace these parts immediately if they have damage that will prevent them from being properly secured to your motorcycle or able to securely hold cargo DO NOT ATTEMPT TO USE THIS ACCESSORY IF e You do not understand these installation and use instructions e You do not und
14. oose warrants this product for defects in materials design or workmanship for a period of one year after retail purchase Items that are defective will be repaired or replaced by MOOSE at its sole discretion Damage caused by improper use or improper installation is not a defect therefore repair or replacement of a damaged accessory will not be covered under this warranty This warranty contains other provisions and conditions so please visit www mooseracing com for additional information Thank you for purchasing your MOOSE Expedition Pannier Mounts You can count on MOOSE s quality innovation service and style We want you to be completely satisfied If you have any comments or are not satisfied with the performance of your accessory please contact your MOOSE retailer directly The images in this instruction set may be different than your accessory or motorcycle 91M TRO1 R1 04 04 2014 11 400311
15. r For additional sealing apply some silicone sealant to the threads 2 and underside of the head 3 of the eight 6mm button head screws supplied with your mounts NOTE The sealant will not compromise the fastening capability of your hardware Move to STEP 16 STEP 16 Place the mounting lip on the bottom of the pannier so it s four mounting holes align with the line of four holes you drilled into the pannier Make sure the lip is oriented so its opening is facing down Insert the 6mm button head screw through the holes inside the pannier Use a 10mm wrench 5 or socket to tighten the nuts 6 as you hold the screws 7 with a 3 Phillips screwdriver 8 Repeat on the other pannier CAUTION Tighten all of the hardware evenly After the initial tightening of the hard ware refer to the table on page 8 for final torque specification Move to STEP 17 STEP 17 TIP If you will be removing and reinstalling your panniers frequently install some double sided tape at the indicated locations 9 between the outer wall of the bag and the plastic protector This will ease mounting as it will prevent the protector from flaring away from the pannier NOTE Obtain the double sided adhesive tape from your local hardware store Move to STEP 18 The images in this instruction set may be different than your accessory or motorcycle 91M TRO1 R1 04 04 2014 11 400311 STEP 18 Each pannier is secured to the
16. s clearance for the protruding rivet heads 0 NOTE You can use other band panniers with your MOOSE pannier mounts While the buffer drill template shapes will not exactly match another brand pannier the hole relationships will allow you to attach the mounting hardware so the luggage can attach to the pannier mounts Use care when selecting the mounting methods for non MOOSE panniers on the mounts Move to STEP 10 STEP 10 Position the buffer template so it aligns with the contours and edges of the pannier Use some masking tape 41 to temporarily hold the buffer template in place for marking the dill hole locations Move to STEP 11 Continued on next page The images in this instruction set may be different than your accessory or motorcycle 91M TRO1 R1 04 04 2014 11 400311 STEP 11 Use a pencil to mark the center of the mounting holes in the pannier TIP Avoid using a permanent marker or paint pen to mark the drill locations This is so you can clean off a mark if needed For dark color panniers you can use a white grease pencil Move to STEP 12 STEP 12 Remove the buffer template from the pannier and use a center punch tool to create a pilot dent in the surface of the aluminum CAUTION Use a spring loaded center punch tool to create the indentation Avoid using a solid punch with a hammer or another method which could cause you to dent or scratch the surface of the pannier Move to STEP 13 STEP 13 Using
17. th your pannier mounts are a pair of plastic buffer drill template sheets These sheets have been engineered to mate perfectly with the outer wall contours of the MOOSE Expedition Panniers You will use the sheets to mark the location of the holes you will need to drill in the panniers to install the mounting hardware supplied in this kit After the holes are drilled and cleaned the plastic sheets are then attached to the panniers to help protect the luggage and the mounts from abrasive wear DRILL BIT SIZES REQUIRED Refer to the template illustration at right and sizes listed below to select the proper size drill bits required to place holes in your pan niers for the mounting kit hardware 5 This hole is not used for these mounts DO NOT DRILL 6 Use a 5 16 drill bit for the upper 8mm mounting hardware 7 Use a 1 4 drill bit for the 6mm hardware that retains the lower mounting lip NOTE Use a 1 2 drill bit or a formal tool to deburr holes after they have been drilled Move to STEP 9 STEP 9 Set your pannier box down on a protected surface with the lid removed and place the buffer drill template on the side that will face the motorcycle s chassis This is the side of the pannier that has the riveted joint The buffer drill template s shape determines its placement on the pannier The angular edges 8 indicates the top of the buffer tem plate The buffer template s other shapes fit with the pannier s bumpers and there i
18. y be different than your accessory or motorcycle 91M TRO1 R1 04 04 2014 11 400311 HARDWARE TORQUE VALUES As the final step of the pannier mount installation process you must tighten all of the new hardware and any other related hardware on your motorcycle These fasteners should be tightened to the torque values specified in your vehicle s Owner s Manual and Service Manual For fasteners not listed in those manuals refer to the torque table below Threads should be treated with a thread locking agent before installation 5MM SCFOW wesessssserssseereseeeaes 3 4ft Ilb 0 35 0 5 kg m 5mm bolt amp nut sss 3 4ft Ilb 0 35 0 5 kg m OMM SCIOW esssscssssesssstsseeessees 5 8 ft lb 0 7 1 1 kg m 6mm bolt amp nut sss 6 9 ft lb 0 8 1 2 kg m 6mm flange bolt amp nut 7 10 ft lb 1 0 1 4 kg m 8mm bolt amp NUE cesses 13 18 ft lb 1 8 2 5 kg m 8mm flange bolt amp nut 14 21 ft lb 2 0 3 0 kg m 10mm bolt amp Nut sessen 22 29 ft lb 3 0 4 0 kg m 10mm flange bolt amp nut 22 29 ft lb 3 0 4 0 kg m 12mm bolt amp Nut ween 36 43 ft lb 5 0 6 0 kg m Most of the supplied fasteners are flange type please pay attention to the different torque specifications this hardware The majority of the nuts supplied with your mount set are self locking type However it is still recommend to use a locking agent on all bolt and nut threads Suggest the use of Three Bond Hi Strength Thr
Download Pdf Manuals
Related Search