User Manual - Speck Pumps
Contents
1. x X ____ Figure 6 LED Functionality Table century 12 7 Green VS 165 6 2 User Interface Key Pad Overview If power is connected to the V Green 165 motor pressing any of the following buttons referred to in this section 6 2 could result in the motor starting Failure to recognize this could result in personal injury or damage to equipment 1 STEP 1 Set Schedule gt DURATION and SPEED 2 STEP2 Set Schedule gt DURATION and SPEED 3 STEP 3 Set Schedule gt DURATION and SPEED 4 OVERRIDE Settings DURATION and SPEED 5 START 6 STOP 6 3 Set the Schedule If power is connected to the V Green 165 motor pressing any of the following buttons referred to in this section 6 3 could result in the motor starting Failure to recognize this could result in personal injury or damage to equipment set the DURATION and SPEED for the V Green 165 using the keys on the User Interface The schedule is based on a 24 hour schedule and will repeat each day of the week ACTIVE _E I __O _ ACTIVE __L _ __ gt p seed srer2 seed OVERRIDE sre a seed OVERRIDE SETTING Q SETTING RS RPM POWER RS POWER E j 0 FAULT FAULT Mo Contury Century The highest speed rating for the V Green 165 is 3450 RPM and the lowest is 600 RPM Unless a new user defined schedule is entered the V Green2. 7 165 3 2 Quick Start Guide User defined custom schedule A V Green 165 user can set the program DURATION and SPEED for STEP 1 STEP 2 STEP 3 amp OVERRIDE keys NOTE V Green 165 must be Stopped Press STOP Key for program ming DURATION and SPEED of the STEP 1 STEP 2 and STEP 3 keys OVERRIDE DURATION and SPEED can be programmed when the V Green 165 is either stopped or running Press the STEP 1 key The STEP 1 button and DURATION setting LEDs will illuminate The bar graph will show default DURATION for STEP 1 ACTIVE ACTIVE geen E E E E Q SETTING O DURATION SPEED SETTING DURATION SPEED HRS RPM POWER i POWER FAULT FAULT Century Press UP or DOWN arrows to change the DURATION 2 Press the STEP 1 key again to change the SPEED setting The SPEED setting LED will illuminate The bar graph will show default SPEED for STEP 1 3 Press UP or DOWN arrows to change the SPEED Press any STEP or OVERRIDE key to save the DURATION and SPEED settings for STEP 1 If the user decides not to save the settings pressing the STOP key will revert back to the previously stored setting century 6 07 V Green 165 5 Press STEP 2 STEP 3 or OVERRIDE key Repeat steps 1 4 to program the corresponding DURATION and SPEED for each button 6 Press START to run the V Green 165 based on the
3. Secure the suction fitting to the front of the pump casing part 101 using four 4 6 x 22mm tapping screws part 917 CAUTION Screws should be HAND TIGHT DO NOT use drills or pneumatic tools DO NOT over tighten 4 Install the 70 x 6mm o ring part 919 on the back of the discharge fitting Secure the discharge fitting to the top of the pump casing part 101 using four 4 6 x 22mm tapping screws part 917 CAUTION Screws should be HAND TIGHT DO NOT use drills or pneumatic tools DO NOT over tighten 5 Insert the pump risers part 182 1 amp 182 2 into base plate part 894 See Exploded View 6 Insert the motor supports part 920 921 into the base plate part 894 See Exploded View 7 When connecting pipework to pump with threaded ports it is recommended that thread seal tape be used If the suction pipe is not sealed correctly the pump will not prime properly and will pump small volumes of water or none at all 8 When installing the pump care should be taken to see that the suction line is below water level to a point immediately beneath and the pump to ensure quick priming via a flooded suction line The height between the pump and the water level should not be more than five 5 feet BONDING As required by National Electrical Code Article 680 22 the pump motor must be electrically bonded to the pool structure reinforced bars etc by a solid copper conductor not smaller than 8 AWG 8 4 w
4. buttons for at least three seconds The active LEDs for STEP 1 STEP 2 and STEP 3 will illuminate temporarily indicating the keypad is un locked NOTE While operating in key lockout mode the motor can still be stopped by pressing the stop key If no digital or serial input is present the motor will remain stopped If the motor is being controlled by a digital or serial input the motor will only temporarily stop for 4 minutes See section 6 9 for more information on temporary stop POWER FAULT century 20 20 V Green 165 6 8 Motor Pause The V Green 165 user interface has a motor pause feature that will allow the user to temporarily stop the V Green 165 for maintenance work without disrupting the 24 hour schedule i e for backwashing the filter If the V Green 165 is currently running the user can press and hold the START button for more than three 3 seconds and the V Green 165 will stop and remain off until the user presses and holds the START button again for more than three 3 seconds The START and OVERRIDE buttons will blink once every second indicating that the motor pause feature is enabled These LEDs will stop blinking once this feature is canceled 6 9 Temporary Stop with Digital Serial Input Temporary stop functionality only works while the V Green 165 is being controlled by a digital or serial input If the motor is being controlled by the integrated key pad and STOP
5. 165 will operate based on the following factory default schedule 13 century Table 3 Factory default schedule Schedule Tables Use the tables below to record a personalized operating schedule Recording the planned schedule in the table below will make the pro gramming process easier and will help the user remember the custom settings in case of inadvertent loss of schedule The user interface will not allow the user to program an overlap between different STEPs of the schedule The STEP currently being set will always take priority over any previous settings In the event a user attempts to program with a combined duration greater than 24 hours the current STEP setting will be retained whereas the other two STEP settings will be cleared to zero hours requiring the user to reset them Prior to beginning the actual programming process it is advisable for the user to review the planned schedule as outlined in chart form to ensure the cumulative duration is not greater than 24 hours and no overlaps exist It is always a good idea to double check your programmed settings for accuracy once you have completed the programming process century 14 Setup 2 Table 4 Custom Schedule 64 Running V Green 165 from Keypad If power is connected to the V Green 165 motor pressing any of the following buttons referred to in this section 6 4 could result in the motor starting Failure to recognize this could result in personal injury or d
6. 2 Navigation Overview Increases decreases selected value Pressing any key following a change accepts the current value displayed inside the setting gt gt POWER O FAULT Cine Figure 1 V Green 165 User Interface Button Descriptions 3 century If power is connected to the V Green 165 motor pressing any of the following buttons referred to in section 2 could result in the motor starting Failure to recognize this could result in personal injury or damage to equipment Note The START button must be pressed for the V Green 165 to operate The START LED will illuminate after the button has been pressed indicating the V Green 165 is capable of operating Pressing the stop button will turn off the START LED and stop the motor if running V Green 165 Features e Simple user interface Digital inputs for compatibility with pool automation systems Motor design reduces noise emissions e UV and rain proof enclosure Freeze Protection Manual OVERRIDE Compatibility w V Green 270 user interface sold as a separate accessory High efficiency electromechanical motor and control design Benefits of adding an optional V Green 270 user interface with the V Green 165 motor Ability to conduct field troubleshooting i e view FAULT codes and real time operating parameters Ability to set a pump running schedule based on a real clock setting 1 must input actual time which then determines pu
7. Florida 32256 Under no condition will products be accepted after the expiration of the Limited Warranty Period Speck Pumps Pool Products Inc shall not bear any costs or risks incurred by Buyer in shipping a defective pump and motor to Speck Pumps Pool Products Inc or in shipping a repaired or replaced pump and motor to Buyer Technical Support Address Speck Pumps 8125 Bayberry Road Jacksonville FL 32256 USA Date of Installation Installed by Hours M F 8 00 am 5 00 pm EST Serial Number Toll Free 800 223 8538 Phone 904 739 2626 For Service Call Fax 904 737 5261 Website www usa speck pumps com Manufactured by Speck Pumps Jacksonville Florida USA All Rights Reserved This document is subject to change without notice 2999999319 Rev 0215 EasyFit SECTION 5 REPLACEMENT PARTS amp EXPLODED VIEW 412 1 143 721 AI 917 156 1 156 2 156 3 919 Alternate Discharge Fittings 903 918 153 917 i Alternate Suction Fittings 153 3 153 2 153 1 153 4 917 153 6 917 2999999319 Rev 0215 EasyFit SECTION 5 REPLACEMENT PARTS amp EXPLODED VIEW continued PART DRAWING QTY DESCRIPTION NUMBER NUMBER REQUIRED 2921116022 160 2 1 LOCK RING WITH HANDLES LID 2901410122 101 1 C
8. OR REPRESENTATIVES BE LIABLE FOR ANY SPECIAL INDIRECT INCIDENTAL EXEMPLARY OR CONSEQUENTIAL DAMAGES OR LOSS INCLUDING TIME MONEY GOODWILL AND LOST PROFITS IN ANY WAY WHICH MAY ARISE HEREUNDER OR FROM THE USE OF OR INABILITY TO USE THE PUMP AND MOTOR OR THE PERFORMANCE OR NONPERFORMANCE OF ANY OBLIGATION UNDER THIS LIMITED WARRANTY THIS PARAGRAPH THE WARRANTY DISCLAIMERS IN PARAGRAPH 4 ABOVE AND THE SOLE AND EXCLUSIVE REMEDY SET FORTH IN PARAGRAPH 1 ABOVE SHALL APPLY EVEN IF SPECK PUMPS POOL PRODUCTS INC HAS BEEN NOTIFIED OF THE POSSIBILITY OR LIKELIHOOD OF SUCH DAMAGES OCCURRING WHETHER SUCH LIABILITY IS BASED ON CONTRACT TORT NEGLIGENCE STRICT LIABILITY PRODUCTS LIABILITY OR OTHERWISE AND EVEN IF ANY REMEDY STATED HEREIN FAILS OF ITS ESSENTIAL PURPOSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF SPECIAL INDIRECT INCIDENTAL EXEMPLARY OR CONSEQUENTIAL DAMAGES OR LOSS SO THE ABOVE EXCLUSIONS AND LIMITATIONS MAY NOT APPLY 6 This Limited Warranty gives the Buyer specific legal rights and the Buyer may also have other rights which vary from state to state 7 A return merchandise authorization must be obtained from Speck Pumps Pool Products Inc before returning any product Products returned without an RMA will be refused and returned unopened to the Buyer All returned products are to be sent freight prepaid and insured for Buyer s protection to the manufacturer at 8125 Bayberry Road Jacksonville
9. is pressed the motor will stop and remain stopped The V Green 165 has a temporary stop feature that will immediately stop the V Green 165 when being controlled by a serial or digital input The user can press the STOP button while the V Green 165 is running and the V Green 165 will stop and stay off for four 4 minutes Once this time has elapsed the V Green 165 will return to normal operation and accept an input from digital or serial input source Refer to section 9 for additional details on digital inputs NOTE If the V Green 165 is operating from serial or digital input the 0 RPM LED of the bar graph will blink once every second indicating the temporary stop feature has been activated After the specified time period the V Green 165 will return to normal operation and accept an input from any digital or serial input source Refer to section 9 for ad ditional details on digital inputs 21 century 6 10 Reset Factory Defaults The V Green 165 user interface has a Reset to Factory Defaults feature to restore the schedule settings back to the original values programmed at the factory The user must press and hold the STOP and OVERRIDE buttons for three 3 seconds to reset the settings back to factory defaults All of the Ul bar graph LED s will flash three 3 times to confirm the settings were restored to factory defaults 7 Priming The V Green 165 will always run the PRIMING sequence when starting from
10. pro grammed 24 hour schedule 7 Pressing the STOP button will stop the V Green 165 NOTE The V Green 165 can only be set to operate on a 24 hour schedule user attempts to program a schedule with a combined duration for all three steps greater than 24 hours the V Green 165 software will retain the current STEP time duration only and will zero out the other two STEP time settings As an example if STEP 1 equals eight 8 hours STEP 2 equals nine 9 hours and STEP 3 equals eight 8 hours for a combined 25 hours the V Green 165 will retain the setting for the current Step being programed and zero out the remain ing two For details regarding the set up of the three steps as part of a 24 hour schedule see section 6 7 century 7 Green VS 165 4 Overview NOTICE The V Green 165 can and should be optimized to suit individual pool conditions Specific conditions including pool size other devices features and environmental factors can all impact the optimal settings Program customization may require some trial and error to determine the most satisfactory settings as dictated by the conditions In all cases setting the V Green 165 at the lowest speed for the longest duration is the best strategy to minimize energy consumption However conditions may require running the V Green 165 at a higher speed for some dura tion of time each day to maintain proper filtration to achieve satisfactory sanit
11. support so that it is readily accessible for service and maintenance 4 Though the pump is designed for outdoor use it is advised to protect the pump from continuous direct heat Install the pump in a well ventilated location protected from excessive moisture flooding sprinklers rain downspouts etc 5 Protect the pump against flooding and excess moisture prevent foreign objects from clogging air circulation around motor All motors generate heat that must be removed by providing proper ventilation 6 DO NOT store or use gasoline or other flammable vapors or liquids in the vicinity of this pump DO NOT store pool chemicals near the pump 7 DO NOT remove any safety alert labels such as DANGER WARNING or CAUTION Keep safety labels in good condition and replace missing or damaged labels 8 Provide access for future services by leaving a clear area around the pump Allow plenty of space above the pump to remove lid and basket for cleaning 1 2 INSTALLATION 1 This pump is designed as a direct replacement for pumps made by several manufacturers It can also be installed as a new pump with easy to connect unions Refer to Figure 1 amp Table 1 for various connection options 2 Use Figure 1 to select the appropriate suction fitting part 153 discharge fitting part 156 pump risers part 182 1 amp 182 2 and motor supports part 920 921 3 Install the 76 x 6mm o ring part 918 on the back of suction fitting
12. the OFF state except when starting in OVERRIDE The factory Prime settings are 2600 RPM for three 3 minutes 8 Freeze Protection NOTICE The freeze protection function will NOT operate if the START button is not pressed This can be confirmed by verifying that the START LED is illuminated In the event that the outside air temperature drops below a set threshold the V Green 165 will automatically turn on assuming the START button has been pressed and circulate the pool water The Freeze Protection will run according to the following conditions utilizing the factory default settings Freeze Protection turn ON temperature 39 F Freeze Protection Duration 8 Hours By utilizing the V Green 270 user interface accessory sold separately these factory default settings can be changed Once this eight 8 hour period has elapsed the V Green 165 will check the ambient temperature again If the temperature is still below the set threshold the V Green 165 will run for an additional 8 hours If the temperature is above the threshold the V Green 165 will automatically return to the 24 hour based schedule century 22 Green VS 165 9 Control with Digital Inputs The user can run the V Green 165 at the programmed STEP 1 STEP 2 STEP 3 or OVERRIDE speeds by utilizing the four digital inputs STEP 1 STEP 2 STEP 3 or OVERRIDE are equivalent to Digital Input 1 2 3 or 4 respectively NOTE The controller i
13. 185 0 to 50 C 32 F to 122 F Relative 0 to 95 non condensing 27 century V Green m 165 14 Troubleshooting Guide Diagnosing certain symptoms may require close interaction with or in close proximity to components that are energized with electricity Contact with electricity can cause death personal injury or property damage When trouble shooting the V Green 165 diagnostics involving electricity should be cared for by a licensed professional Symptom Possible Causes Potential Solutions Controller DIP switches not Verify that the DIP switches of SW100 un configured properly der the controller terminal box cover are in the correct position Refer to section 10 V GREEN 165 Replace fuse reset breaker GFI Mains Voltage is not present FAILS Tighten mains wire connections TO START User Interface is not connected Check connections at J201 connector Verse Check if the V Green 165 can be rotated by hand and remove any blockage V Green 165 shaft is damaged Replace V Green 165 Check that back of V Green 165 is free V GREEN 165 Debris in contact with fan and debris Use compressed air IS Debris in strainer basket Clean strainer basket NOISY Check that mounting bolts of V Green 165 Loose mounting and pump are tight Check that V Green 165 is spinning by Impeller is loose looking at fan on back of V Green165 If so check that pump impeller is correctly V GREEN 165 install
14. 2901415600A 156 1 FITTING STANDARD DISCHARGE KIT 2901418213 182 1 1 RISER FRONT 2901418223 182 2 2 RISER REAR OPTIONAL PARTS 2901415306 153 1 1 FITTINGS 1 5 NPT SUCTION Ultra Flow 2901415316 1531 1 FITTINGS 2 NPT SUCTION Ultra Flow 2901415307 153 2 1 FITTINGS 1 5 NPT SUCTION WhisperFlo IntelliFlo 2901415317 1532 1 FITTINGS 2 NPT SUCTION WhisperFlo IntelliFlo 2901415305 153 3 1 FITTINGS 1 5 NPT SUCTION Super Pump SuperFlo 2901415315 1933 1 FITTINGS 2 NPT SUCTION Super Pump SuperFlo 2901415308 153 4 1 FITTINGS 1 5 NPT SUCTION Dura Glas Max E Glas 2901415318 153 4 1 FITTINGS 2 NPT SUCTION Dura Glas Max E Glas 2901415323 153 6 1 FITTINGS 2 NPT SUCTION Dyna Glas 2901415602 156 1 1 FITTINGS 1 5 NPT DISCHARGE Pentair Hayward STA RITE 2901415612 156 2 1 FITTINGS 2 NPT DISCHARGE Pentair Hayward STA RITE 2901415623 156 3 1 FITTINGS 2 NPT DISCHARGE STA RITE Dyna Glas 2901418212 182 1 1 RISER FRONT Ultra Flow 2901418213 182 1 1 RISER FRONT WhisperFlo IntelliFlo Dyna Glas 2901418214 182 1 1 RISER FRONT Dura Glas Max E Glas 2901418222 182 2 2 RISER REAR Ultra Flow 2901418223 182 2 2 RISER REAR WhisperFlo IntelliFlo Dyna Glas 2901418221 182 2 2 RISER REAR Super Pump SuperFlo 2901418224 182 2 2 RISER REAR Dura Glas Dyna Glas Hayward and Super Pump are regist
15. ASING 2901413002 130 2 NAME PLATE ORANGE 2901411304 113 1 FLANGE 2901489400 894 1 2901416102 161 2 1 SEAL HOUSING I IV V VI 2901416103 161 2 1 SEAL HOUSING 1 65 2901417421 174 2 1 DIFFUSER I 2921317421 174 2 1 DIFFUSER 1 65 2901417422 174 2 1 DIFFUSER IV V 2901417420 174 2 1 DIFFUSER VI 2920750200 502 1 FLOATING EYE SEAL I 2901450700 502 1 FLOATING EYE SEAL IV V TBD 230 1 IMPELLER I 2901423015 230 1 IMPELLER H 113 5 3mm 2901423009R 230 1 IMPELLER 118 5 0mm 2901423009 230 1 IMPELLER 1 65 124 5 0mm 2901423016 230 1 IMPELLER IV 120 8 7mm 2901423017 230 1 IMPELLER 120 10 0mm 2901423013 230 1 IMPELLER VI 120 7 8mm 2923591201 903 1 PLUG CASING DRAIN 1 4 2920141240 412 4 1 O RING DRAIN PLUG 11 x 2 5mm 2921141210 412 1 1 O RING LID 137 x 5mm 2901441210 412 2 1 O RING CASING 206 x 6mm 2920141210 412 5 1 O RING DIFFUSER 90 x 5mm 2991000091 900 10 SCREW CASING HEX SLOT M7 x 48mm SS 2901116010 160 1 1 LID CLEAR 2920343310 433 1 MECHANICAL SEAL 20mm COMPLETE 2920110200 598 1 MOTOR FLANGE 56 FRAME 2991400028 914 2 4 SCREW 3 8 16 x 2 2901414303 143 1 BASKET ONE PIECE 5879006022 917 8 SCREW 6 x 22mm A2 2901441270 918 1 O RING SUCTION FITTING ALL 76 x 6mm 2901441282 919 1 O RING DISCHARGE FITTING ALL 67 x 6mm 2902089420 920 1 ADAPTER 2920889410 921 T LEGO SPACER 2901415300A 153 1 FITTING STANDARD SUCTION KIT
16. Installation Operating and Service Manual EasyFit 1 65 THP Swimming Pool Pump 5 D mps ts u Table of Contents Technical Support Address Hours Toll Free Phone Fax Website Email 1 Pump Manual 3 11 2 Motor Manual 12 43 Speck Pumps 8125 Bayberry Road Jacksonville FL 32256 USA Monday Friday 8 00 am to 5 00 pm EST 800 223 8538 904 739 2626 904 737 5261 www usa speck pumps com technical usa speck pumps com Date of Installation Installed by Serial Number For Service Call Manufactured by Speck Pumps Jacksonville Florida USA All Rights Reserved This document is subject to change without notice Rev 02 2015 SAVE THESE INSTRUCTIONS 7 speck OWNERS ren i READ THIS MANUAL CAREFULLY BEFORE USING THE SPECK PUMP Important Notice This manual contains important information about the installation operation and safe use of this product This information should be given to the owner and or operator of this equipment WARNING This product must be installed and serviced by a qualified pool professional and must conform to all national state and local codes WARNING Before installing this product read and follow all warning notices and instructions which are included Failure to follow safety warnings and instructions can result in severe injury death or property damage Call 800 223 8538 or visit www usa speck pum
17. NOTE Pressing a STEP key other than for the STEP currently running will cause an immediate transition to the newly selected STEP The V Green 165 will continue with the programmed schedule from that point forward NOTE If STOP is pressed during normal schedule operation the 24 hour schedule will stop When START is pressed again the 24 hour schedule will start from STEP 1 NOTE If power is lost while the V Green 165 is running a 24 hour schedule upon restoration of power the V Green 165 will start the 24 hour schedule from STEP 1 NOTE If a digital input provided from an external source is detected the V Green 165 will start running on the STEP 1 STEP 2 STEP 3 or OVERRIDE speed corresponding to the digital input Upon removing the digital input provided from an external source the V Green 165 will stop and the user will need to press START to begin the 24 hour sched ule operation However if START was already pressed prior to receiving a digital input then the V Green 165 will resume running the 24 hour schedule once the digital input is removed NOTE Pressing STOP at any time turns the V Green 165 OFF and clears the start time for the 24 hour schedule century 16 7 Green 165 6 5 OVERRIDE The V Green 165 is equipped with an OVERRIDE feature which can be engaged to temporarily run at higher or lower speeds ranging between 600 to 3450 RPM Once the OVERRIDE duration has elapsed the V Green 165
18. T is present and the motor is not running only the FAULT LED and power LED will illuminate When a FAULT is present and the motor is running then the FAULT LED will illuminate During the FAULT condition the bar graph LEDs on the interface will turn OFF However the power LED start LED amp active STEP LED will remain illuminated When a FAULT is present and the FAULT LED is illuminated only the STOP key will function The remaining buttons become disabled When the FAULT LED 15 continuously ON i e not blinking a FAULT is present in the controller When the FAULT LED is blinking every one 1 second a FAULT is present in the user interface When the FAULT has cleared the FAULT LED will turn OFF Once the FAULT is cleared if the V Green 165 was previously running it will automatically resume running the normal schedule Please see Section 14 for troubleshooting issues and their resolutions century 26 13 Specifications Input Voltage Input Current Input Frequency Control Terminals Auxiliary Load Terminals Maximum Continuous Load Speed Range Environmental Rating Agency Approval Ambient Conditions Storage Operating Humidity 208 230 Vrms nominal 10 5 10 0 Arms Single phase 60 Hz 18 30V AC 24V AC 20 9 30V DC 12 24V DC 20 N A 1 65 THP Total Horse Power 600 3450 RPM NEMA Type 3R R C XDNW2 E302804 R C XDNW8 E302804 Al US 40 to 85 C 40 F to
19. amage to equipment 1 Press the START key and the V Green 165 will run the programmed 24 hour duration schedule The START event will be stored in the controller Should a power outage occur the V Green 165 will automatically re start at STEP 1 when power is restored 2 The V Green 165 will always run the PRIMING sequence when it Starts from the OFF state including when it automatically restarts following a power outage The default Prime setting is defined in the Priming section of this document 3 The V Green 165 then starts running in STEP 1 at the programmed DURATION and SPEED The ACTIVE LED for STEP 1 will turn ON The DURATION and SPEED setting LEDs along with the re spective bar graph LED will blink back and forth every three 3 seconds d g SETTING O RPM POWER POWER FAULT FAULT O6 Century Century century 19 SOc V Green 165 4 This sequence will then repeat for STEP 2 and then STEP 3 with out the V Green 165 stopping 5 At the end of STEP the V Green 165 will wait if necessary for the completion of the 24 hour schedule During this waiting period if applicable all of the active step LEDs will remain OFF However the START LED will still be illuminated After completion of the 24 hour schedule the system restarts at STEP 1 and this cycle will repeat indefinitely until the user presses the STOP key
20. and maintained in strict compliance with this Limited Warranty and that the claim was timely submitted within the Limited Warranty Period and or e Buyer s failure to comply with the conditions and contingencies set forth in paragraph 3 below 3 The Limited Warranty is expressly conditioned and contingent upon Buyer s strict compliance with each of the following a Installation of the pump and motor by an experienced and qualified pool industry professional and a licensed electrician who is licensed within the jurisdiction in which the pump and motor is installed and will be used and b Buyer s operation and maintenance of the pump and motor in strict accordance with Speck Pumps Pool Products Inc s printed operator maintenance manuals delivered with the pump and motor 4 DISCLAIMER THE LIMITED WARRANTY IS THE ONLY WARRANTY MADE AND IS IN LIEU OF ALL OTHER WARRANTIES AND ANY AND ALL IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY THE IMPLIED WARRANTY AGAINST INFRINGEMENT AND THE IMPLIED WARRANTY OR CONDITION OF FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY LIMITED IN THEIR SCOPE AND DURATION TO THE TWO YEAR TERM OF THE LIMITED WARRANTY SET FORTH HEREIN SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATION MAY NOT APPLY TO THE BUYER 9 TO THE FULLEST EXTENT PERMITTED BY LAW IN NO EVENT SHALL SPECK PUMPS POOL PRODUCTS INC OR ITS OFFICERS DIRECTORS EMPLOYEES SHAREHOLDERS AGENTS
21. ation The User Interface is located on top of the V Green 165 To the right of the STEP buttons is the OVERRIDE button This button can be used to operate the V Green 165 at speeds outside of the normal operating schedule aa Figure 2 V Green 165 Overview century 8 VS 165 5 Wiring The V Green 165 controller must be wired according to the locally adopted version of the NEC A licensed qualified electrician should complete the wiring for this product Failure to comply with this may result in death serious personal injury or property damage The V Green 165 controller must be wired according to the locally adopted version of the NEC A licensed qualified electrician should complete the wiring for this product The controller is designed to operate with 208 230 Vrms single phase power The V Green 165 is designed to handle either a bare wire connection or a quick disconnect connection The quick disconnect tab is 0 250 and will handle any commonly available mating connectors For a direct wire connection the wire insulation should be stripped to a length of approxi mately 0 33 The terminal block is capable of handling solid or stranded wire up to 12 AWG in size The screw for the mains connections should be properly tightened to a torque value of 10 in Ib Red or White Table 1 Mains Connection Pis Wire Color Description 1201 1 cs J201 Bax Table 2 Communication Conn
22. cess Use only water as a lubricant to install both sides of the seal Make sure both sides of the seal ceramic and spring portion are clean Gently wipe polished faces with soft and dry cotton cloth Surfaces can easily be damaged by dirt and scratching Use a drop of loc tite to secure the impeller nut Hayward and Super Pump are registered trademarks of Hayward Industries Inc 1 4 WINTERIZING CAUTION The pump must be protected when freezing temperatures are expected Allowing the pump to freeze will cause severe damage and void the warranty There are two options when winterizing the pump Option 1 Drain all the water from the pump system equipment and piping Remove drain plug s DO NOT replace plug s Store plug s in the strainer basket for winter Keep the motor covered and dry Option 2 Drain all the water from the pump system equipment and piping Remove the pump and motor from the plumbing and store indoors in a warm and dry location NOTE When the winter season is over the pump will need to be check and primed prior to start CAUTION DO NOT run the pump dry If the pump 15 run dry the mechanical seal will be damaged and the pump will start to leak at the seal If this occurs the mechanical seal will need to be replaced ALWAYS maintain the proper water level in your pool Continued operation in this manner could cause 1055 of pressure resulting in damage to the pump casing impeller and mechan
23. d repair 3 Low flow a Dirty filter Back wash filter when filter pressure is high or clean cartridges b No skimmer basket Clean skimmer and pump strainer basket c Closed valves or blocked lines See problem 1 d Suction air leak See problem 1 4 Noisy operation of motor a Bad bearings Noise when shaft is turned up by hand Motor is hot in bearing area when running Replace bearing 5 Motor runs hot These motors will run hot to the touch however this is normal They are designed that way Thermal overload protector will function to turn them off if there is an overload or high temperature problem Excessive heat can be cause by a Low voltage Increase size of electrical wire Be sure motor is operating on correct voltage b Installed in direct sun Shield motor from sun s rays c Poor ventilation Do not tighten cover or enclosure motor 6 Noisy operation of pump a Air leak in suction line Bubbles Repair leak Check suction pipe see through lid in in water returning to pool at inlet place O ring clean b Restricted suction line due Remove blockage or increase suction pipe size Make to blockage or under size pipe sure strainer tank is clean Are all suction valves fully Indicated by high vacuum reading open at pump suction c Foreign matter gravel metal Disassemble pump and remove foreign matter from etc in pump impeller impeller d Cavitation Improve suction condit
24. e Operation 12 6 1 LED and Function Overview 12 6 2 User Interface Key Pad Overview 13 6 3 Set the Schedule 13 6 4 Running V Green 165 from Key Pad 15 OVERRIDE 17 6 6 Schedule Advance 18 oS 20 21 6 9 Temporary Stop with Digital Serial Input 21 6 10 Reset Factory 22 PE REUTERS 22 8 Freeze Protection su asit 22 9 Control with Digital Inputs 23 10 DIP SWILCNES cn een 24 11 Care and Maintenance 25 12 FAULT nee ne 25 13 Specifications ee een 27 14 Troubleshooting 28 1 century 7 Green VS 165 oafety is emphasized throughout this user manual These are safety alert symbols and signal words They alert the user to potential per sonal injury hazards Obey all safety messages to avoid possible injury or death or damage to equipment and other property DANGER DANGER DANGER indicates a hazardous situation wh
25. ection 9 century Power should be turned off when installing servicing or repairing electrical components Observe all warning notices posted on the existing equipment V Green 165 and in these installation instructions EARTH L2 L1 RED OR WHITE BLACK EARTH Figure 3 Mains Connection Diagram century 10 E VS 165 V Green 165 Controller UI DIGITAL INPUT CONNECTOR J202 Automation System or Solar System Controller eene EXTERNAL SUPPLY ac oeni External Supply Range 18 30V AC 24V 20 9 30V DC 12 24V DC 20 Figure 4 Wiring Diagram for Digital Inputs Access to these terminals is in close proximity to the mains connectors which carry line voltage capable of causing personal injury or damaging the equipment if contact is made Power should be turned off when accessing this area Figure 5 Digital Input connector 11 century V Green 6 6 7 165 User Interface Operation 1 LED and Function Overview Alternates between DURATION and SPEED 8 pinktorthretimes asee Poweron __ _ _ emma EE E RestoreDetautsetngs X Mora _ x J x Temporaystop pow pow 0 x _____ x x po Serial Communication UT Freeze Protecton FTF we x _ _ __ _ ___
26. ed Check plumbing connections and verify Air leak RUNS dos they are tight BUT NO Check for blockage in strainer or suction ide piping FLOW Clogged or restricted plumbing Checked for blockage discharge piping including partially closed valve or dirty pool filter century 28 Disclaimer The information in this document incorporates proprietary rights and is not to be duplicated wholly or in part without the express written permission of Regal Beloit America Inc Copyright 2013 The text and images in this document are not to be modified without express written permission of Regal Beloit Corporation and or Regal Beloit America Inc Regal Beloit America Inc 531 North Fourth Street Tipp City OH 45371 Fax 937 667 5030 www centuryelectricmotor com Customer Service 1 800 262 6484 Please refer to our website www pool motors com for updates to this printed manual Distribution Marketing 1325 Heil Quaker Blvd LaVergne TN 37086 Phone 866 887 5216 Fax 800 468 2062 www pool motors com 2013 Regal Beloit Corporation 2516831 002 10 13 A Regal Brand REGAL
27. edule Advance mode can be canceled by press ing the STOP key NOTE The OVERRIDE button will still function when the Schedule Advance mode is active This will allow the user to run the V Green 165 during the period of the Schedule Advance mode NOTE While the V Green 165 is in the Schedule Advance mode if a user presses STEP 1 STEP 2 STEP 3 or the START key the system Will start the normal schedule and the Schedule Advance mode will be canceled NOTE While the V Green 165 is in the Schedule Advance mode if a user presses the STOP key then the Schedule Advance mode is canceled NOTE If power is lost while the V Green 165 is in the Schedule Advance mode then the 24 hour schedule will automatically start when power is restored 19 century 6 7 Key Lockout Key lockout will not prevent the motor from being stopped by pressing the STOP button If the motor is operating in key lockout mode and being controlled through a digital serial input the motor will only temporarily stop 4 min it will then restart The V Green 165 user interface has a key lockout feature to prevent unwanted changes to the settings To lock the keys hold down the STEP 1 STEP 2 and STEP 3 buttons all at the same time for at least three seconds The active LEDs for STEP 1 STEP 2 and STEP 3 will blink for 30 seconds indicating that the keypad is locked The user can unlock the keys by holding down the same three STEP
28. ered trademarks of Hayward Industries Inc Pentair SuperFlo WhisperFlo IntelliFlo Ultra Flow Sta Rite amp Dyna Glas Dyna Pro Dura Glas and Max E Glas are trademarks and or registered trademarks of Pentair Water Pool and Spa Inc and or its affiliated companies 2999999319 Rev 0215 EasyFit READ THIS MANUAL CAREFULLY BEFORE USING THE SPECK PUMP AX DANGER DO NOT BLOCK SUCTION __ AN 1 Pump suction is hazardous and can trap and drown or disembowel bathers DANGER 2 Blocking suction with body may cause severe or fatal injury i 3 Do not use or operate swimming pools spas or hae hot tubs if a suction outlet cover is missing broken Hazardous suction Can trap hair body or 10056 parts causing severe injury or death 4 All suction outlets covers must be maintained They Do not block suction must be replaced if cracked broken or missing 1 DANGER 5 All suction outlets must have correctly installed screw fastened covers in place 6 The pump suction system must provide protection against the hazard of suction entrapment or hair entrapment entanglement Hazardous suction 7 Provide at least two hydraulically balanced 3 apart Can trap hair or body main drains with covers as suction outlets for each parts causing severe circulating pump suction line injury or death Do not block suction 1 To avoid dangerous or fatal electrical shock turn OFF power to motor bef
29. ical seal Ceramic Ring Rubber Collar Impeller Shaft Figure 2 0 Pump Seal Housing Sealing Spri pring Surfaces Assembly Pentair SuperFlo WhisperFlo IntelliFlo Ultra Flow Sta Rite Dyna Glas Dyna Pro Dura Glas and Max E Glas are trademarks and or registered trademarks of Pentair Water Pool and Spa Inc and or its affiliated companies 2999999319 Rev 0215 EasyFit SECTION 2 TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSES SOLUTION 1 Pump will not prime a Suction air leak Make sure the see through lid and o ring are clean and properly positioned Tighten see through lid hand tight Tighten all pipes and fittings on suction side of the pump Be sure water in the pool is high enough to flow through skimmer b No water in pump Make sure strainer tank is full of water c Closed valves or blocked lines Open all valves in system Clean skimmer and strainer tank Open pump and check for clogging of impeller d Low voltage to motor Check voltage at motor If low pump will not come up to speed 2 Motor does not turn a No power to motor Check that all power switches are on Be sure fuse or circuit breaker is properly set Time set properly Check motor wiring at terminals b Pump jammed With power off turn shaft It should spin freely If not disassemble an
30. ich if not avoided will result in death or serious injury WARNING WARNING indicates a hazardous situation which if not avoided could result in death or serious injury CAUTION CAUTION indicates a hazardous situation which if not avoided could result in minor or moderate injury NOTICE NOTICE NOTICE identifies potential equipment damage or failure conditions and alerts personnel to potentially dangerous situations century 2 7 Green VS 165 1 Introduction The V Green 165 is a premium efficiency variable soeed motor that provides tremendous program flexibility in terms of motor speed and time settings The variable speed V Green 165 is intended to enable running at the lowest speeds needed to maintain a sanitary environment which in turn minimizes energy consumption Pool size the presence of additional water features chemicals used to maintain sanitary conditions and environmental factors will impact optimal programming necessary to maximize energy conservation The V Green 165 is for use with 208 230 Vrms nominal and in pool pump applications ONLY Connection to the wrong voltage or use in other application may cause damage to equipment or personal injury The integrated electronics interface controls the speed settings as well as the run durations The V Green 165 can run at speeds ranging between 600 and 3450 RPM and 1 rated for 208 230 Vrms at an input frequency of 60 Hz
31. ions Reduce suction life reduce number of fittings increase pipe size Increase discharge pressure and reduce flow by throttling discharge valve 2999999319 Rev 0215 EasyFit SECTION 2 TROUBLESHOOTING GUIDE continued PROBLEM POSSIBLE CAUSES SOLUTION 7 Motor overload protection a Motor is not connected properly Check wiring diagram on motor kicks out b Low voltage due to under size Check with volt meter Increase size of supply wire wire or low incoming voltage Reports low supply voltage to power company Voltage at motor must be within 10 of motor nameplate voltage c Wrong size heaters in protective Heaters should be one size larger than full load amps device shown on motor nameplate d Overload due to binding in pump Indicated by high amperage readings on motor or wrong size impeller binding shaft Disassemble unit and correct SECTION 3 SERVICING INFORMATION When calling the manufacturer regarding a question or The serial number is located on the pump either on the problem with your pump please have the serial number casing and or motor Replacement parts may be available available from your installer SECTION 4 LIMITED WARRANTY Speck Pumps Pool Products Inc grants solely to the original consumer purchaser Buyer of the pump and motor the following personal non transferable and limited warranty on the following terms and conditions the Limited Warranty the pump a
32. ire via the external copper bonding lug on the pump motor GROUNDING Permanently ground the pump motor using a conductor of appropriate size Connect to the 10 green headed ground screw provided inside the motor terminal box For more information about the motor operation refer to the motor manual NOTE DO NOT connect to electric power supply until the unit is permanently grounded 1 1 2 NPT 6 W78 50 019 6 W78 50 020 4 W78 50 008 3 W78 50 005 2 W78 50 007 1 W78 50 006 2 85 1 6 32 1 97 5 10 N A 3 13 1 97 ORWN gt 2999999319 Rev 0215 EasyFit SECTION 1 EQUIPMENT OPERATION AND MAINTENANCE Option Suction Fitting Discharge Fitting Replaces Pump Modell W78 50 006 1 5 2 Pentair Ultra Flow W78 50 007 1 5 2 Pentair WhisperFlo amp IntelliFlo W78 50 005 1 5 or 2 W78 50 008 1 5 2 STA RITE Dura Glas 8 Max E Glas Hayward Super Pump amp Super Pump VS Pentair SuperFlo 6 W78 50 019 W78 50 020 _ STA RITE Dyna Glas Table 1 0 Replacement Pump Connection Options 1 3 MAINTENANCE The pump requires little or no service other than reasonable care and periodic cleaning of the strainer basket DO NOT strike basket to clean When cleaning the basket inspect the lid o ring for damage and replace if necessary NOTE t is
33. mp start and stop times Ability to remotely mount the V Green 270 user interface provides easy access of user interface depending on pump location Ability to configure prime speed and prime duration century 4 7 N Green oz 165 Ability to configure freeze protection temperature Ability to view actual speed and power of the V Green 165 in real time Ability to adjust the V Green 165 motor speed in 25 RPM increments to fine tune flow for certain pool installations e Battery backup to store time setting 3 Quick Start Instruction If power is connected to the V Green 165 motor pressing any of the following buttons referred to in section 3 could result in the motor starting Failure to recognize this could result in personal injury or damage to equipment 3 1 Quick Start Guide Using the factory default schedule The following table describes the factory default settings for DURATION and SPEED order Button Duration Speed In Hours In RPM STEP 1 3100 STEP 2 2600 STEPS 8 1600 OVERRIDE 3450 Pressing the START key will start the V Green 165 based on the factory default schedule NOTE If power is cycled to the V Green 165 and the user does not press the STOP key the V Green 165 will automatically start and run the programmed default schedule shown in the chart above This feature ensures that the V Green 165 will re start in the event of a power outage 5 century
34. nd motor is warranted to be free of material defects in materials or workmanship under normal use for a period of two 2 year beginning on the date of the Buyer s purchase of the pump and motor Not withstanding any provisions herein to the contrary the warranties and obligations hereunder shall not in any event extend for more than three 3 years beyond the date of shipment of the pump and motor from the factory the Limited Warranty Period The Limited Warranty is subject to each of the following additional terms and conditions 1 IN THE EVENT OF ANY BREACH OF THE LIMITED WARRANTY SPECK PUMPS POOL PRODUCTS INC S ENTIRE OBLIGATION AND LIABILITY TO BUYER AND BUYER S SOLE AND EXCLUSIVE REMEDY SHALL BE AS FOLLOWS Speck Pumps Pool Products Inc will at its option either repair or replace the pump and motor or refund to Buyer the purchase price actually paid by Buyer for the pump and motor subject to the Limited Warranty Speck Pumps Pool Products Inc shall have no obligations under the Limited Warranty unless Buyer delivers timely written notice to Speck Pumps Pool Products Inc of the Limited Warranty claim within the Limited Warranty Period and returns the pump and motor to Speck Pumps Pool Products Inc if requested To the fullest extent permitted by law Speck Pumps Pool Products Inc expressly disclaims any liability for and the Limited Warranty does not include or cover any labor costs or other expenses in connec
35. normal for a few drops of water to escape from the mechanical seal from time to time This is especially true during the break in period The mechanical seal may come worn and or loose during the course of time depending on the running time and water quality If water continually leaks out a new mechanical seal should be fitted After long periods of NOT operational seasonal storage etc the pump must be checked for ease of rotation while it is switched off WARNING Before servicing the pump switch off the circuit breakers at the power source Severe personal injury or death may occur if the pump starts while your hand 15 inside the pump Place a screwdriver allen wrench or appropriate tool in the end of the motor shaft and turn it clockwise OR Remove the fan cover and turn the fan in a clockwise direction manually This may require removal of the cover at the rear of the motor or small circular cap at the rear center of the motor To Replace the Mechanical Seal To replace the mechanical seal remove the sixteen 16 bolts holding the casing to the seal housing Slide the motor part including the seal housing out Remove the terminal cover from the rear of the motor and secure the center motor shaft with a 1 2 wrench Remove impeller nut by turning it counter clockwise when facing it Pull the impeller from the motor shaft noting the position of the seal Remove the seal from the impeller shaft To re assemble reverse the pro
36. ore working on electrical connections 2 To reduce the risk of electrical shock unplug Hazardous voltage motor before working on pump or motor Can shock burn or cause death Disconnect power before working on pump or motor SAVE THESE INSTRUCTIONS 2999999319 Rev 0215 EasyFit Eco Friendly Electric Moto Green Choice ma m Century A Regal Brand COPYRIGHT Copyright 2013 Regal Beloit America Inc Tipp City Ohio All rights reserved TRADEMARKS All trademarks and registered trademarks are the property of their respective companies The information in this document incorporates proprietary rights and is not to be duplicated wholly or in part without the express written permission of Regal Beloit Corporation and or Regal Beloit America Inc June 2013 USA O V Green ni 165 Table of Contents nee 2 1 3 2 Navigation Overview 3 3 Quick Start Instruction 5 3 1 Quick Start Guide Using Factory Default Schedule 5 3 2 Quick Start Guide User Defined Custom Schedule 6 4 8 WANO 9 6 User Interfac
37. ps com for additional copies of these instructions IMPORTANT SAFETY INSTRUCTIONS When installing and using this electrical equipment basic safety precautions should always be followed including the following 1 READ AND FOLLOW ALL INSTRUCTIONS 2 WARNING To reduce the risk of injury do not permit children to use this product unless they are closely supervised at all times 3 WARNING Risk of Electrical Shock Connect only to a branch circuit protected by a ground fault circuit interrupter GFCI Contact a qualified electrician if you cannot verify that a circuit is protected by a 4 WARNING To reduce the risk of electric shock replace any damaged cord immediately 5 DO NOT install within an outer enclosure or beneath the skirt of a hot tub or spa 6 CAUTION This pump is for use with permanently installed pools and may also be used with hot tubs and spas if so marked DO NOT use with storable pools A permanently installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage A storable pool is constructed so that it is capable of being readily disassembled for storage and reassembled to its original integrity 7 The unit must be connected only to a supply circuit that is protected by a ground fault circuit interrupter Such a GFCI should be provided by the installer and should be tested on a routine basis To test the GFCI push
38. s rated to accept digital inputs of 18V 30V AC 24V AC 20 and 9 30V DC 12 24V DC 20 NOTE The V Green 165 will detect either a 50 60Hz for AC input or an active low signal for DC digital inputs The items below describe the functionality of the digital inputs 1 Ifthe user provides any one of the 4 digital inputs then the corresponding ACTIVE STEP LED will blink every one 1 second The SPEED LED and corresponding bar graph LED will be illumi nated to indicate the Digital Input is functioning properly 2 The START LED will be OFF when a digital input is present Access to these terminals is in close proximity to the mains connectors which carry line voltage capable of causing personal injury or damaging the equipment if contact is made Power should be turned off when accessing this area NOTE A generic wiring diagram is provided in figure 7 for connecting the V Green 165 to a System Level Controller This concept can be applied to a solar system or any other type of control system NOTE There is no schedule for digital inputs The timing for each speed is controlled directly by the digital inputs NOTE The digital inputs have the highest priority amongst all the inputs 1 keypad serial or digital Therefore the serial commands as well as the User Interface inputs will be ignored when a digital input is present NOTE If more than one digital input switch is present then the V Green 165 will gi
39. tain electronics that are cooled by a fan mounted to the V Green 165 In order to ensure optimum reliability of this product it is recommended to clean the fan inlet on the back of the V Green 165 once a month It is also important to keep this area free of large debris such as leaves branches mulch plastic bags etc 12 FAULT Status While the FAULT LED is illuminated the motor will not run upon clearing the fault the motor may automatically resume running depending on where in the schedule the FAULT occurred This may cause personal injury or damage to the equipment The paragraphs below illustrate the possible faults that can occur with the V Green 165 If the V Green 165 does not restart automatically fol lowing the FAULT cycle ac power to the V Green 165 and wait five 5 minutes If this does not correct the situation please contact Customer Service at 1 800 262 6484 The V Green 165 reads the FAULT status and provides feedback to the user via the FAULT LED The V Green 165 will illuminate the FAULT LED when a FAULT is present The V Green 165 will stop and remain OFF when the FAULT is present Once the FAULT 15 cleared if the V Green 165 was previously running it will automatically resume running the normal schedule SETTING DURATION SPEED POWER FAULT 25 century 20 V Green 165 Below is the behavior of the FAULT LED when a FAULT is detected 1 When a FAUL
40. the test button The should interrupt power Push the reset button Power should be restored If the GFCI fails to operate in this manner the GFCI is defective If the GFCI interrupts power to the pump without the test button being pushed a ground current is flowing indicating the possibility of an electric shock Do not use this pump Disconnect the pump and have the problem corrected by a qualified service representative before using 8 TO REDUCE RISK OF ELECTRICAL SHOCK A copper bonding connector 8 AWG is provided for bonding the motor to all metal parts of the swimming pool spa or hot tub structure and to all electrical equipment metal conduit and metal piping within 5 feet of the inside walls of a swimming pool spa or hot tub when the motor is installed within 5 feet of the inside walls of the swimming pool spa or hot tub NOTE To installer and or operator of the Speck owimming Pool Pump the manufacturer s warranty will be voided if the pump is improperly installed and or operated SAVE THESE INSTRUCTIONS SECTION 1 EQUIPMENT OPERATION AND MAINTENANCE 1 1 LOCATION 1 Locate the pump as close to the pool as practical Consult local codes for minimum distance between pool and pump 2 The piping should be as direct and free from turns or bends as possible as elbows and other fittings greatly increase friction losses 3 Place pump on a solid foundation which provides a rigid and vibration free
41. ting the OVERRIDE duration to 0 HRS will not allow you to change the duration setting while the motor is running The motor will have to be stopped in order to change the OVERRIDE settings if the duration is set to 0 HRS 6 6 Schedule Advance DANGER Do not perform any maintenance on the motor while the motor is in Schedule Advance Mode The motor may start without warning This event could cause death or serious personal injury The Schedule Advance mode allows the user to press the START button at one time of the day with the 24 hour schedule starting at a different time of day The V Green 165 can run in the Schedule Advance mode by using the OVERRIDE button and upon completion will begin the programmed 24 hour schedule at STEP 1 DURATION and SPEED The following steps should be followed to set Schedule Advance mode 1 With the V Green 165 stopped press and hold the START key for mno nn more than three 3 seconds The ster over START LED will blink at a rate of one second per pulse The DURATION S SETTING setting LED and respective bar graph Ga 2450 ME LED will remain turned ON until the Schedule Advance mode is complete FAULT century 18 7 Green be 165 2 Press the UP or DOWN arrows to set the desired delay time after which the 24 hour schedule should start The Schedule Advance mode will automatically start after the desired delay time is selected The Sch
42. tion with the removal transportation shipment insurance replacement repair or installation of repaired or replaced parts or for any other costs or expenses or damages to property or things including but not limited to those arising in connection with the use of or inability to use the pump and motor 2 To the fullest extent permitted by law the Limited Warranty will be void and of no force or effect and Speck Pumps Pool Products Inc will have no liability responsibilities or obligations to Buyer or with respect to the pump and motor in the event of the occurrence of any one or more of the following a Any damage to the pump and motor caused by Buyer any third party ground movement other natural forces acts of God or any other sources or causes not arising from a breach of the Limited Warranty excluding ordinary wear and tear 6 Any replacement modification alteration or repair of any parts or components of the pump and motor by anyone other than Speck Pumps Pool Products Inc Any abuse misuse accident tampering with improper installation or modification of the pump and motor or any other actions inactions or failures to act that violate the terms and conditions of this Limited Warranty 2999999319 Rev 0215 EasyFit SECTION 4 LIMITED WARRANTY continued d Buyer s failure or inability to present an invoice bill receipt or other documentation clearly evidencing that the pump and motor was installed
43. ve priority to the highest number digital input There fore OVERRIDE has highest priority followed by STEP 3 then STEP 2 then STEP 1 23 century V Green 165 NOTE If no digital input is detected the V Green 165 will automatically start the 24 hour schedule if the START key was pressed prior to the application of a digital input Access to these terminals is in close proximity to the mains connectors which carry line voltage capable of causing personal injury or damaging the equipment if contact is made Power should be turned off when accessing this area B COM Hl ____ pa Load Load Load Load 1 2 3 4 Line Line Line Line Figure 7 System Level Control Wiring Diagram 10 DIP Switches Access to these terminals is in close proximity to the mains connectors which carry line voltage capable of causing personal injury or damaging the equipment if contact is made Power should be turned off when accessing this area The DIP switches can be used to configure different settings for the V Green 165 Each DIP switch and their corresponding function is defined in Table 5 Switch Function Power output on off Not Used Table 5 DIP Switch Functions Figure 8 DIP Switches century 24 7 Green be 165 11 Care and Maintenance The V Green 165 is both reliable and robust in harsh environments However this product does con
44. will automatically return to the programmed schedule 1 Pressing the OVERRIDE key while the V Green 165 is running will cause the V Green 165 to start running in the OVERRIDE mode at the programmed DURATION and SPEED The active LED for OVERRIDE will illuminate The DURATION and SPEED setting LEDs along with its respective bar graph LED will blink back and forth at three 3 second intervals 2 The UP DOWN arrows allow the user to configure OVER RIDE DURATION and SPEED These settings can be changed while the V Green 165 is running These settings are stored each time the UP DOWN arrows are pressed a SETTING POWER FAULT NOTE When the OVERRIDE duration ends the V Green 165 resumes the 24 hour schedule at the point in the currently programmed 24 hour schedule where it normally would be running at that time The OVER RIDE duration will not affect the start or stop times of the 24 hour sched ule For example if OVERRIDE runs during a period overlapping with a later part of STEP 1 and an early part of STEP 2 the start time of STEP 3 is not affected 17 century 07 V Green 165 NOTE Pressing Holding OVERRIDE key for more than three 3 seconds will cancel OVERRIDE mode NOTE During the OVERRIDE mode the V Green 165 will not start with the priming sequence NOTE It is recommended that you do not set the OVERRIDE duration to 0 HRS Set
Download Pdf Manuals
Related Search