K5081B & K5074B & K5075B INST 6.3.13
Contents
1. age only Rebuild service and replacement parts will be available and sold separately by Pro Comp Contact Pro Comp for specific service charges Pro Comp accepts no responsibility for any altered product improper installa tion lack of or improper maintenance or improper use of our products E Mail info procompusa com PLACE Website www procompusa com WARRANTY REGISTRATION Fax 310 747 3912 NUMBERS Ph 1 800 776 0767 16 lt lt lt lt HERE2. 18 Install the strut assembly into the strut ie eames ee ae bar using a cutting wheel or another suit tower and start the upper three OE nuts able tool Make sure that the bottom of the strut is NOTE Bever y careful not to cut into as well See ILLUSTRATION the sway bar l 22 Install the sway bar drop brackets 90 19 Using the floor jack raise the lower con Na A aan A OE Sh mount Hardware trol arm and connect the lower ball joint bracket to the knuckle using the 2 previ ously removed OE bolts Apply thread locking compound to the bolts Torque ock 5394 to the original sway bar mounting holes in the frame with the protruding rounded portion on the outside facing the rear of the vehicle Secure to the frame using the OE bolts Torque to 30 ft lbs Coil Bucket Strut Assembly 23 24 25 26 27 28 29 30 See ILLUSTRATION 2 Reinstall the sway bar to the new sway bar drop brackets using the supplied 3 8 X 1 1 4 bolts and hardware Torque the 3 8 bolts according to the chart on page 13 See ILLUSTRATION 2 Reconnect the sway bar end links using the previously removed OE hardware Torque the nut to 52 ft lbs Carefully position a floor jack under the front differential and raise the pad to con tact the differential Remove the OE differential mounting nuts and bolts Install the differential mount spacers 90 2840 between the diff
3. LIGHTS Illustration 2 Sway Bar Drop Bracket Installation Drvr Side FRONT of VEHICLE OE Bolt 3 8 X 1 1 4 Bolt and Hardware 7 FRONT of VEHICLE 1 FJ REAR INSTALLATION Block the front tires and raise the rear of the vehicle Support the frame with jack stands forward of the rear springs Remove the rear wheels 3 Remove the shocks on both sides of the vehicle It may be necessary to slightly raise the axle to unload the shocks for re moval Lower the rear axle enough to remove the coil springs from the front spring pockets Save the factory isolators for re use NOTE Be sure to support the axle while the springs and shocks are removed 5 Unbolt the track bar from the rear axle mount and secure up and out of the work area Save the hardware for reinstallation Unbolt the sway bar end links from the sway bar Save the hardware for reuse On both sides of the vehicle support the rear end with a jack and unbolt the lower control arm at the axle Carefully lower the rear end to ease in the new coil spring installation Using the factory isolators install the Pro Comp coil springs 57492 into the spring buckets and raise the rear axle into place Make sure the coil spring seats properly on the lower spring perch Install your new Pro Comp shocks 923553 w shaft end up to the OE shock mounts Torque the upper mounting hardware to 18 ft lbs and the lower OE mounting bolt to 72 ft Ib
4. helper spring consisting of one or more flat leaves installed at the bottom of the leaf pack DO NOT install the add a leaf spring in or be low the helper spring 1 Block the front tires and raise the rear of the vehicle Support the frame with jack stands forward of the rear springs 2 Remove the rear wheels 3 Remove the shocks on both sides of the vehicle It may be necessary to slightly raise the axle to unload the shocks for re moval 4 Work on one side of the vehicle at a time Support the rear axle with a floor jack and remove the U bolts on the driver side Loosen the U bolts on the passenger side and lower the rear axle NOTE Be sure not to over extend the rear brake lines 6 Use C clamps to hold the leaves of the rear leaf spring together and remove spring center bolt 7 Disassemble the leaf spring and insert the add a leaf 13129 See ILLUSTRA TION 3 NOTE Add a leaf will be placed in the spring assembly progressively according to length For example if the existing leaves are 32 long and 25 long and the add a leaf is 28 long place the add a leaf between the existing leaves 8 Using the C clamps re clamp and bolt the leaf pack back together using the supplied center bolt 97 380 with the head of the bolt facing down See ILLUSTRATION 3 9 Install the lift block Uf the vehicle is equipped with one making sure the pins fit properly into the holes on the spring perch Use your
5. normal and usually does not indicate a faulty product However if you are uncertain about some aspect of the installation process please feel free to call our tech support department at the number listed on the cover page We do not recom mend that you modify the Pro Comp parts in any way as this will void any warranty ex pressed or implied by the Pro Comp Suspension company Optional Equipment Available from your Pro Comp Distributor Tacoma 4WD 2WD Pre Runner Suspension Lift Kit 2005 2011 Non VSC 57096 57096MX or 2005 2012 w VSC 57396 57396MX Coil Over Upgrade Kit 57097 57097MX Traction Bars 72500B Mounting kit 72083B Skid Plate 57196 Light Bar 25000 CV Style Driveshaft 57098 To be used in conjunction with Pro Comp 6 lift kits FJ AWD amp 2WD Suspension Lift Kit 57007 57007MX Coil Over Upgrade Kit 57008MX Also Check out our outstanding selection of Pro Comp tires to compliment your new installation 57491 K5074B K5075B Revised 6 3 13 Important Tire and wheel choice is crucial in assuring proper fit performance and the safety of your Pro Comp equipped vehicle For this application we recommend a 17 X 8 non hub centric wheel with a maximum backspacing of 4 1 2 PN 8089 7883 Additionally a quality tire of radial design not exceeding 33 tall X 12 5 wide tire PN 27033 is recommended Installation of larger wheels may be possible but must not exceed 5 of backspacing Be
6. sembly with a suitable coil spring com pressor so that the coil spring has about 3 8 play in the strut and remove the up per strut isolator retaining nut NOTE Do not use an impact gun to remove the retaining nut It will damage the strut shaft 13 Remove the OE coil spring isolator from the upper strut mounting plate See IL LUSTRATION 1 IMPORTANT Be sure that the factory isolator stays with the top mount as sembly NOTE Inspect the front shock as semblies for any damage or fluid leakage Replace if necessary 14 Install the new compressed coil spring 57491 and OE isolator onto the new strut assembly 622053 and re attach the upper strut mount plate using the stock hardware Torque the upper strut mount ing plate retaining nut to 20 ft Ibs See ILLUSTRATION 1 15 Decompress the coil spring on the strut assembly Make sure that the spring is seated correctly into the strut assembly and aligned with the previously scribed index mark on the upper strut mounting plate See ILLUSTRATION 1 16 Install the lower strut bolt in the original position and torque to 100 ft lbs for the FJ and 61 ft lbs for the Tacoma 57491 K5074B K5075B Revised 6 3 13 17 ON THE DRIVER SIDE ONLY install the bolts to 118 ft lbs oh espace Ove ey onto the diver 20 Unbolt the sway bar frame mount brack side upper strut mount studs See ILLUS eis Savethe OF hardware for tense TRATION 1 l l 21 fully cut the OE coll
7. 4 2 7 73 03700034 3 8 SAE Gr 8 Washer 8 2 7 90 2840 Differential Mount spacer 2 90 6935 Hardware Pack Diff Spacer 1 14F150H101 14mm 1 5 X 150mm Gr 10 9 Hex bolt 2 14RWFLI HV 200 125 14mm Hardened Flat Washer 4 L4FNNLZ 14mm 1 50 Nylock Nut 2 90 8076 Skid Plate Spacer 4 90 6937 Hardware Pack Skid Plate Spacer 1 8C40H10Z DIN933 8mm 1 25 X 40mm Hex Bolt 4 3IRWFLZ USS PC 5 16 USS Flat Washer 4 58075 Block Kit 1 1 2 1 95 150 1 1 2 LIFT BLOCK 2 4 12 13 90126 U BOLTS 9 16 x 2 525 x 10 00 4 4 12 20 65302 HARDWARE PACK U Bolts 1 13 30330 9 16 FLAT WASHER 8 4 12 13 10423 9 16 HIGHNUT 8 12 622053 ES6000 Front Strut 2 1 6 925518 ES9000 Rear Shock 2 gt o 57491 K5074B K5075B Revised Introduction ab This installation requires a professional mechanic We recommend that you have access to a factory service manual for your vehicle to assist in the disassem bly and reassembly of your vehicle It contains a wealth of detailed information Prior to installation carefully inspect the vehicle s steering and driveline systems paying close attention to the tie rod ends ball joints wheel bearing preload pitman and idler arm Additionally check steering to frame and suspension to frame attaching points for stress cracks The overall vehicle must be in excellent working condition Repair or replace all worn or damaged parts Read the instructions caref
8. 400 W Artesia Blvd Latest Revision Compton CA 90220 Fax 310 747 3912 6 3 13 Ph 1 800 776 0767 E Mail info procompusa com Website www procompusa com CLLL LL off road driven PRO COMP SUSPENSION K5075B K5081B 2005 2011 2005 2012 K5074B Toyota Tacoma Toyota Tacoma 2007 2009 as A AWD WDE Toyota F 4WD y TT 3 Lift Kit 3 Lift Kit 3 Lift Kit W Rear Add A Leaf W Rear Blocks This document contains very important information that includes warranty information and instructions for resolving problems you may encounter Please keep it in the vehicle as a permanent record 57491 K5074B K5075B Revised K5074B FJ Kit Parts List 6 3 13 Part Description Qty Illus Page 57491 BOX KIT 1 57491 1 Front Coil Spring 2 1 6 91 3396 Strut Spacer 1 90 5394 Front Sway Bar Drop Bracket 2 2 7 90 6223 Hardware Pack Sway Bar 1 70 0371251800 3 8 16 X 1 1 4 Gr 8 Hex Bolt 4 2 7 72 037100816 3 8 16 USS Stover Nut 4 2 7 73 03700034 3 8 SAE Gr 8 Washer 8 2 7 90 2840 Differential Mount spacer 2 90 6935 Hardware Pack Diff Spacer 1 14F150H101 14mm 1 5 X 150mm Gr 10 9 Hex bolt 2 14RWFLI HV 200 125 14mm Hardened Flat Washer 4 L4FNNLZ 14mm 1 50 Nylock Nut 2 90 8076 Skid Plate Spacer 4 90 6937 Hardware Pack Skid Plate Spacer 1 8C40H10Z DIN933 8mm 1 25 X 40mm Hex Bolt 4 31RWFLZ USS PC 5 16 USS Flat Washer 4 57492 Rear Coil Spring 2 622053 ES6000 Front S
9. ause of our commitment to quality and manufacturing excellence we are able to stand behind our products FOREVER It is Pro Comp s Promise that if one of our suspension products breaks not due to misuse neglect or vandalism we will replace it Whether you are the original purchaser or not you can be assured that we will make it right The Pro Comp Promise covers all suspension products including shocks and steering stabilizers Buy Pro Comp Suspen sion today and enjoy it for the rest of your life That s our Pro Comp Promise Notice to Owner Operator Dealer and Installer Vehicles that have been enhanced for off road performance often have unique handling characteristics due to the higher center of gravity and larger tires This vehicle may handle react and stop differently than many passenger cars or unmodified vehicles both on and off road You must drive your vehicle safely Extreme care should always be taken to prevent vehicle rollover or loss of control which can result in serious injury or even death Always avoid sudden sharp turns or abrupt maneuvers and allow more time and distance for braking Pro Comp reminds you to fasten your seat belts at all times and reduce speed We will gladly answer any questions concerning the design function maintenance and correct use of our products Please make sure that the Dealer Installer explains and delivers all warning notices warranty forms and instruc tion sheets included with Pro Comp
10. erential mounts and the front crossmember Secure the diff mount using the supplied 14mm X 150mm bolts large 14mm washer and 14mm hard ware Torque per specifications in the chart on page 7 Reconnect the ABS lines Reinstall the front skid plate if applica ble using OE hardware in the front holes and the 2 supplied spacers 90 8076 and 2 8mm X 40mm bolts and 5 16 washers in the rear holes Reinstall the mid plate if applicable us ing the 2 supplied spacers 90 8076 and Sway Bar Drop Bracket 90 5394 l 57491 K5074B K5075B Revised 6 3 13 2 8mm X 40mm bolts and 5 16 wash ers in the front holes and the OE hard ware in the rear holes 31 Reinstall the front wheels Reinstall the wheels and lower the vehicle to the ground Torque the lug nuts according to the wheel manufacturers recommenda tions NOTE Trimming of the wheel well liner on the backside of the fender well may be necessary depending on the tire wheel combination 32 Lower the vehicle onto the ground and tighten the upper strut tower OE nuts to 47 ft lbs 33 With the vehicle on the ground torque the lower A arm cam bolts to 100 ft lbs 34 Recheck all hardware for proper installa tion and torque at this time IMPORTANT BE SURE TO BRING THE VEHICLE TO A REPUTA BLE ALIGNMENT SHOP TO BE ALIGNED IMPORTANT IF THE STEERING WHEEL IS NOT CENTERED PROPERLY IT WILL TRIGGER THE ANTI LOCK BRAKE AND TRACTION CONTROL WARNING
11. floor jack to raise the axle to the spring Make sure the pin on the leaf spring fit into the holes on the new lift block See ILLUSTRATION 3 NOTE These blocks are slightly ta pered and the short side of the taper is ori ented to the front of the vehicle 10 Secure the assembly with the U bolts and high nuts and washers Do not torque the U bolts at this time See ILLUSTRA TION 3 NOTE Make sure the block sits flush on the axle perch 11 Repeat the installation on the other side of the vehicle 12 When the installation of the remaining side is complete torque the U bolts to 85 ft Ibs 13 Install your new Pro Comp shocks 925518 w shaft end up to the OE shock mounts Torque the upper mounting hardware to 18 ft lbs and the lower OE mounting bolt to 72 ft Ibs 14 Reinstall the wheels and tires and lower the vehicle to the ground Torque the wheels to the manufacturers recom mended specifications 15 Recheck the wheel lug torque on all four wheels at this time 16 Recheck all hardware for proper installa tion and torque at this time 17 On completion of the installation have the suspension and headlights re aligned 18 After 100 miles recheck for proper torque on all newly installed hardware 19 Recheck all hardware for tightness after off road use 57491 K5074B K5075B Revised 6 3 13 NOTES Oncompletion of the installation have the suspension and head lights re aligned Afte
12. lace your floor jack under the front cross member and raise vehicle Place jack stands under the frame rails behind the front wheel wells and lower the frame onto the stands Remove the jack and place the vehicle back in gear set the emergency brake and place blocks both in front of and be hind the rear wheels 3 Remove the front wheels Save the hard ware for reinstallation Save the hardware for reinstallation 4 Remove the front skid plate and mid plate if applicable 5 Disconnect the ABS lines 6 Disconnect the sway bar end links and remove the lower ball joint cotter pin and nut 7 Loosen but do not remove the lower a arm bolts to allow the lower control arm to pivot on the bushings 8 Remove the 2 bolts from the lower ball joint bracket Save bolts for reinstallation 9 Remove the lower strut bolt from the lower control arm and remove the strut assembly from the vehicle NOTE the direction of the bolt for reinstallation 10 Remove upper strut tower nuts holding 57491 K5074B K5075B Revised 6 3 13 the strut assembly to the strut tower 3 on each side of the vehicle Save for rein stallation 11 Scribe an index mark on the top of the OE coil spring to the upper strut mount ing plate CAUTION The coil is under ex treme pressure and severe bodily injury may occur if the coil spring is disassembled with out using a coil spring compressor 12 Compress the coil spring on the strut as
13. lled out torque specification in the instruction manual Bolt Torque and ID Decimal System Metric System All Torquesin Ft Lbs Maximums 1 2 13 1 75 HHCS Grade 5 Grade 8 M12 1 25x50 HHCS A No of Marks 2 A G Grade Bolt Strength P Property Class Bolt Strength D Nominal Diameter Inches D Nominal Diameter M illimeters T Thread Count Threads per Inch T Thread Fitch Thread Width mm L Length Inches L Lengh Millimeters X Description Hex Head Cap Screw X Description Hex Head Cap Screw 57491 K5074B K5075B Revised 6 3 13 Revisions Page 10 6 11 Updated manual fitment years Added K5081 to cover and BOM pages Added K5081 rear block kit installation text and illustration 4 5 28 13 Added diff spacer 90 2840 90 8076 hardware packs 90 6935 and 90 6937 to the BOM and the text Updated cover logo warranty page and contact information 15 57491 K5074B K5075B Revised 6 3 13 The PRO COMP PROMISE WARRANTY At Pro Comp we know you have many choices when selecting products to personalize your vehicle You should demand nothing but the highest quality available and have total confidence that the products you selected are the best in the industry It is for these reasons that Pro Comp Suspension products are backed by the best warranty in the industry the Pro Comp Promise Pro Comp promises that its products will last a lifetime or we will replace it free of charge It s that simple Bec
14. n the other side of the vehicle When the installation of the remaining side is complete torque the U bolts to 85 ft lbs Install your new Pro Comp shocks 925518 w shaft end up to the OE shock mounts Torque the upper mounting hardware to 18 ft lbs and the lower OE mounting bolt to 72 ft lbs Reinstall the wheels and tires and lower the vehicle to the ground Torque the 12 16 12 wheels to the manufacturers recom mended specifications Recheck the wheel lug torque on all four wheels at this time Recheck all hardware for proper installa tion and torque at this time On completion of the installation have the suspension and headlights re aligned After 100 miles recheck for proper torque on all newly installed hardware Recheck all hardware for tightness after off road use NOTES On completion of the installation have the suspension and head lights re aligned After 100 miles recheck for proper torque on all newly installed hard ware Recheck all hardware for tightness after off road use 57491 K5074B K5075B Revised 6 3 13 w REAR BLOCKS ey Illustration 4 Ms Rear Block Assembly 13 90126 U Bolts Leaf Spring Assembly Add A Leaf if equipped Lift Block 95 150 NOTE This is just an example Your set up may differ slightly from illustration 20 65302 Hi Nuts 13 57491 K5074B K5075B Revised 6 3 13 Use this only as a guide for hardware without a ca
15. product Warranty and Return Policy Pro Comp warranties its full line of products to be free from defects in workmanship and materials for the life of the product Pro Comp s obligation under this warranty is limited to repair or replacement at Pro Comp s option of the defective product Any and all costs of removal installation freight or incidental or consequential damages are ex pressly excluded from this warranty Pro Comp is not responsible for damages and or warranty of other vehicle parts related or non related to the installation of Pro Comp product A consumer who makes the decision to modify his vehicle with aftermarket components of any kind will assume all risk and responsibility for potential damages incurred as a result of their chosen modifications Warranty coverage does not include consumer opinions regarding ride comfort fitment and design Warranty claims can be made directly with Pro Comp or at any factory authorized Pro Comp dealer IMPORTANT To validate the warranty on this purchase please be sure to mail in the warranty card Claims not covered under warranty Parts subject to normal wear this includes bushings bump stops ball joints tie rod ends and heim joints Finish after 90 days Damage caused as a result of not following recommendations or requirements called out in the installation manu als Pro Comp MX Series coil over shocks are considered a serviceable shock with a one year warranty against leak
16. r 100 miles recheck for proper torque on all newly installed hard ware Recheck all hardware for tightness after off road use N Illustration 3 w REAR ADD A LEAF SN Rear Add A Leaf Assembly 97 380 13129 Add A Leaf NOTE This is just an example Your set up may differ slightly from illustration 57491 K5074B K5075B Revised 6 3 13 TACOMA REAR BLOCK KIT INSTALLATION 1 Block the front tires and raise the rear of the vehicle Support the frame with jack stands forward of the rear springs Remove the rear wheels Remove the shocks on both sides of the vehicle It may be necessary to slightly raise the axle to unload the shocks for re moval Work on one side of the vehicle at a time Support the rear axle with a floor jack and remove the U bolts on the driver side Loosen the U bolts on the passenger side and lower the rear axle NOTE Be sure not to over extend the rear brake lines 6 Install the lift block 95 150 making sure the pins fit properly into the holes on the spring perch Use your floor jack to raise the axle to the spring Make sure the pin on the leaf spring fit into the holes on the new lift block See ILLUSTRATION 4 Secure the assembly with the U bolts 13 90126 and high nuts and washers 20 65302 Do not torque the U bolts at this time See ILLUSTRATION 4 NOTE Make sure the block sits flush on the axle perch 8 10 11 Repeat the installation o
17. s IMPORTANT Install one of the supplied 3 4 flat washers onto the mount ing stud before and after the shock is in stalled to the mounting stud 10 Reattach the sway bar end links to the sway bar using the previously removed OE hardware Torque the nut to 52 ft Ibs 12 13 14 57491 K5074B K5075B Revised 6 3 13 Repeat the installation on the other side of the vehicle Check all hardware at this time to ensure that everything is tight Check for ade quate clearance on all repositioned brake lines and emergency brake cables Make sure you check with the suspension fully extended and compressed Reinstall the wheels and lower the vehicle to the ground Torque the lug nuts ac cording to the wheel manufacturers rec ommendations With the vehicle on the ground reinstall the track bar to the rear axle using the pre viously removed OE hardware Torque the OE hardware to 96 ft lbs NOTES On completion of the installation have the suspension and head lights re aligned After 100 miles recheck for proper torque on all newly installed hard ware Recheck all hardware for tightness after off road use 57491 K5074B K5075B Revised 6 3 13 TACOMA REAR ADD A LEAF KIT INSTALLATION NOTE In order to properly install the add a leaf spring it will be necessary to contain the elasticity in the leaf spring with C clamps when the center bolts are re moved Some springs have a factory
18. sure to check fit all wheel and tire combinations before purchasing and installation Violation of these recommendations will not be endorsed as acceptable by Pro Comp Suspension and will void any and all warranties either written or implied Please Note Front suspension and head light realignment is necessary Speedometer and ABS recalibration will be necessary if larger tires 10 more than stock diameter are installed Always use NEW cotter pins on re assembly These items are NOT supplied IT IS ADVISABLE THAT YOU HAVE HELP AVAILABLE WHEN INSTALLING THIS KIT SOME COMPONENTS ARE HEAVY AND AWKWARD ADDI TIONAL HELP IS GOOD INSURANCE AGAINST INJURY NOTE The final height of this kit is dependant upon the engine transmission and body configurations Special Tools Please refer to your service manual for more information A special removal tool is required for safe removal of the tie rods These tools may be purchased at your local Toyota dealer You may be able to rent any of these tools at your local parts store FJ amp TACOMA KIT FRONT INSTALLATION 1 Prior to installing this kit with the vehicle on the ground Measure the height of your vehicle This measurement can be re corded from the center of the wheel straight up to the top of the inner fender lip Record the measurements below LF RF LR RR 2 Ensure that your work space is of ade quate size and the work surface is level Place the vehicle in park P
19. trut 2 1 6 923553 ES9000 Rear Shock 2 OR K5075B Tacoma w Rear Add A Leaf Parts List 57491 BOX KIT 1 57491 1 Front Coil Spring 2 1 6 91 3396 Strut Spacer 1 90 5394 Front Sway Bar Drop Bracket 2 2 7 90 6223 Hardware Pack Sway Bar 1 70 0371251800 3 8 16 X 1 1 4 Gr 8 Hex Bolt 4 2 7 72 037100816 3 8 16 USS Stover Nut 4 2 7 73 03700034 3 8 SAE Gr 8 Washer 8 2 7 90 2840 Differential Mount spacer 2 90 6935 Hardware Pack Diff Spacer 1 14F150H101 14mm 1 5 X 150mm Gr 10 9 Hex bolt 2 14RWFLI HV 200 125 14mm Hardened Flat Washer 4 L4FNNLZ 14mm 1 50 Nylock Nut 2 A 1 1 90 8076 Skid Plate Spacer 57491 K5074B K5075B Revised 6 3 13 90 6937 Hardware Pack Skid Plate Spacer 1 8C40H10Z DIN933 8mm 1 25 X 40mm Hex Bolt 4 31RWEFLZ USS PC 5 16 USS Flat Washer 4 622053 ES6000 Front Strut 2 1 6 925518 ES9000 Rear Shock 2 57096B 5 Rear Add A Leaf Box 1 13129 Add A Leaf 2 3 10 90 3825 Hardware Pack Add A Leaf 1 98 00250 1 2 1 2 Spring Plate Clamps 4 3 10 98 00250 1 2 1 2 Spring Plate Straps 4 3 10 97 380 3 8 X 5 Center Bolt 2 3 10 8337 1 3 8 Fine Gr 8 Nut 2 3 10 OR K5081B Tacoma w Rear Blocks Parts List 57491 BOX KIT 1 57491 1 Front Coil Spring 2 1 6 91 3396 Strut Spacer 1 90 5394 Front Sway Bar Drop Bracket 2 2 7 90 6223 Hardware Pack Sway Bar 1 70 0371251800 3 8 16 X 1 1 4 Gr 8 Hex Bolt 4 2 7 72 037100816 3 8 16 USS Stover Nut
20. ully and study the illustrations before attempting installation You may save your self a lot of extra work Check the parts and hardware against the parts list to assure that your kit is complete Separating parts ac cording to the areas where they will be used and placing the hardware with the brackets before you begin will save installation time Check the special equipment list and ensure the availability of these tools Secure and properly block vehicle prior to beginning installation ALWAYS wear safety glasses when using power tools or working under the vehicle Use caution when cutting is required under the vehicle The factory undercoating is flammable Take appro priate precautions Have a fire extinguisher close at hand Foot pound torque readings are listed on the Torque Specifications chart at the end of the instructions These are to be used unless specifically directed otherwise Apply thread lock retaining compound where specified Please note that while every effort is made to ensure that the installation of your Pro Comp lift kit is a positive experience variations in construction and assembly in the vehicle manu facturing process will virtually ensure that some parts may seem difficult to install Addition ally the current trend in manufacturing of vehicles results in a frame that is highly flexible and may shift slightly on disassembly prior to installation The use of pry bars and tapered punches for alignment is considered
Download Pdf Manuals
Related Search