Induction Plate Activator
Contents
1. x Alluserv Redefining Healthcare Food Service Induction Plate Activator with TempSense Operation amp Service Manual Induction Plate Activators Models AIPH1 amp AIPH2 Operation Unpack the activator and place it on a table or other suitable flat surface The activator is equipped with adjustable feet so it can be leveled on the table top Make sure the plate locator supplied with the activator is attached to the metal housing There are two screws in the rear of the activator that hold the plate locator in place These can be removed so the locator can be taken off for cleaning For the plate activator model AIPH1 plug the activator into a 120 Volt 15 Amp Single Phase 1 Press the green power button on the front panel The digital display should light and read Ld This indicates the activator is ready for a plate to be loaded 2 Place the plate on top of the activator making sure to push it completely back into the plate locator This will center the plate on the activator insuring the most even heating The digital dis play will read hEAt indicating that the plate is being heated 3 When heating is complete approximately 20 seconds the digital display will show rdy indicating that the heating cycle is complete and the plate is hot ready to be removed from the activator and have food placed on it 4 Once a hot plate is removed from the activator the digital dis play will again show Ld and the next plat2. able foot Note Before ordering replacement plate locators always verify the Bauscher plate number that is being used Also if possible verify the part number on the original locator It is located on a sticker inside the locator For service issues Contact the factory toll free at 888 892 2213 ext 103
3. ain harsh chemicals that can damage the stainless steel housing causing it to pit or rust Troubleshooting Digital Display does not light when the off on button is pushed Check to make sure the unit is plugged in and that the receptacle has power to it The digital display shows Ld but plates do not heat when placed on the charger Verify that the plates being used are induction plates and have the gray induction decal on the bottom Verify that the plates are being placed fully against the plate locator and that they are covering the white lens for the IR temperature sensor in the top of the charger If the unit still does not function after the above items have been checked contact the factory Do not attempt to repair this unit It contains no user serviceable parts If the digital display shows error messages E02 or E08 or does not light at all this indicates some type of internal damage to the unit Contact the factory Replacement Plate Locators Part Number A00137 Single Plate Locator for 9 plates 250023 amp 800023 A00138 2 Single Plate Locator for 10 plates 250025 281826 amp 800025 A00143 Single Plate Locator for 9 plate 250024 A00144 Single Plate Locator for 9 plates 281823 amp 8001723 A00145 Single Plate Locator for 4 bowls 253012 amp 595712 A00152 Double Plate Locator for 9 plates 250023 amp 800023 A00157 Double Plate Locator for 10 plates 250025 281826 amp 800025 a Adjust
4. e can be loaded The double induction plate activator model AIPH2 has two heating areas that operate independently of each other Each side has its own power switch and digital display Plug the activator into a 120 Volt 20 Amp Single Phase grounded receptacle NEMA 5 20R The power switch for each side must be pressed to activate that side before it will heat Each side will operate as previously described in the instructions for the single plate activator The two sides can be operated as instructed independently of each other Cleaning Instructions 1 Turn the activator off and remove the plug from the power outlet before cleaning 2 Remove the plate locator from the top of the activator This is done by removing two Phillips head screws in the rear of the locator 3 Wash the locator by hand in a sink with a mild detergent solution Do not wash in a commercial dish machine as the heat could cause the locator to deform 4 Wipe all surfaces of the activator unit with a damp cloth and mild detergent solution 5 If scouring is required on the stainless steel surfaces use a plastic scouring pad and a mild scouring agent 6 When cleaning is complete wipe dry with a clean soft cloth CAUTION e Never spray wash or use excessive water during cleaning e Do not immerse the activator in water or put it in the dishwasher for cleaning e Never use commercial scouring pads They will scratch the top surface of the activator and cont
Download Pdf Manuals
Related Search