English Fitting Instructions: Speed Triple 1050 from VIN 461332 and
Contents
1. IUMP English Fitting Instructions Speed Triple 1050 from VIN 461332 and Speed Triple 1050 R A9758126 A9758293 Thank you for choosing this Triumph genuine accessory kit This accessory kit is the product of Triumph s use of proven engineering exhaustive testing and continuous striving for superior reliability safety and performance Completely read all of these instructions before commencing the installation of the accessory kit in order to become thoroughly familiar with the kit s features and the installation process These instructions should be considered a permanent part of your accessory kit and should remain with it even if your accessory equipped motorcycle is subsequently sold T0834 Parts Supplied 1 Grab rail 1 off 4 Badge adhesive 1 off 2 Rear light moulding 1 off 5 Cleaning wipe 1 off 3 Screw A off Publication part number A9900532 issue 4 DC 70648 1 of 4 Triumph Designs Ltd 2015 This accessory kit is designed for use on Triumph Speed Triple 1050 from VIN 461332 and Speed Triple 1050 R motorcycles only and should not be fitted to any other manufacturer s motorcycle Fitting this accessory kit to any other manufacturers motorcycle will affect the performance stability and handling of the motorcycle This may affect the rider s ability to control the motorcycle and could cause an accident Always have Triumph approved parts accessories and co2. as shown below 1 Grab rail 2 Cleaning area 2 of 4 4 Position the badge centrally on the upper surface of the grab rail Apply firm and even pressure to ensure a good bond is achieved 1 Grab rail 2 Badge 5 Remove the seat as described in the Service Manual 6 Remove the rear side panels as described in the Service Manual 7 Remove the rear light moulding as described in the Service Manual Note Note the orientation of the grommets in the rear light moulding for installation 8 Remove the grommets from the rear light moulding Retain the grommets for reuse Retain the rear light moulding if the motorcycle is to be returned to its original condition T0836 1 Grommets 2 Rear light moulding 9 10 11 1 Stand off rubber right hand side shown Fit the grommets to the rear light moulding from the kit as noted for removal Fit the rear light moulding to the motorcycle as described in the Service Manual Check that the stand off rubbers between the rear light moulding and the subframe are fully located onto their locating tangs 2 Locating tang 3 Rear light moulding 4 Subframe 12 Align the grab rail to the subframe fit the bolts and tighten to 27 Nm 1 Grab rail 2 Bolts 3 Subframe 13 Refit the rear side panels as described in the Service Manual 14 Refit the seat as described in the Service Manual 15 Remove the motorcycle from t
3. he paddock stand 3 of 4 After fitting the accessory kit the motorcycle will exhibit new handling characteristics Operate the motorcycle in a safe area free from traffic to gain familiarity with any new characteristics Operation of the motorcycle when not familiar with any new handling characteristics may result in loss of motorcycle control and an accident The motorcycle must not be operated above the legal road speed limit except in closed course conditions If after fitment of this accessory kit you have any doubt about the performance of any aspect of the motorcycle contact an authorised Triumph dealer and do not ride the motorcycle until the authorised dealer has declared it fit for use Riding a motorcycle when there is any doubt as to any aspect of the performance of the motorcycle may result in loss of control of the motorcycle leading to an accident Never ride an accessory equipped motorcycle at speeds above 80 mph 130 km h The presence of accessories will cause changes in the stability and handling of the motorcycle Failure to allow for changes in motorcycle stability may lead to loss of control or an accident Remember that the 80 mph 130 km h limit will be reduced by the fitting of non approved accessories incorrect loading worn tyres overall motorcycle condition and poor road or weather conditions Only operate this Triumph motorcycle at high speed in closed course
4. nversions fitted by a trained technician of an authorised Triumph dealer The fitment of parts accessories and conversions by a technician who is not of an authorised Triumph dealer may affect the handling stability or other aspects of the motorcycle s operation which may result in loss of motorcycle control and an accident Throughout this operation ensure that the motorcycle is stabilised and adequately supported to prevent risk of injury from the motorcycle falling A torque wrench of known accurate calibration must be used when fitting this accessory kit Failure to tighten any of the fasteners to the correct torque specification may result in loss of motorcycle control and an accident 1 Position the motorcycle on a paddock stand When fitting self adhesive parts care must be taken to ensure positioning is correct and accurate Once the adhesive has been attached to the mounting surface there is no satisfactory method of removal or re positioning if incorrectly aligned Initial bonding is instant full bonding is achieved after 72 hours Note Read the warning notices printed on the cleaning wipe packet The surface to which the badge is affixed must be clean and dry to ensure that the adhesive has a sound base to adhere to Use the cleaning wipe supplied for this purpose 2 Peel off the backing strip from the adhesive badge Using the cleaning wipe provided clean the area of the grab rail
5. on road competition or on closed course race tracks High speed operation should only be attempted by riders who have been instructed in the techniques necessary for high speed riding and are familiar with the motorcycle s characteristics in all conditions High speed operation in any other circumstances is dangerous and will lead to loss of motorcycle control and an accident 4 of 4
Download Pdf Manuals
Related Search