Service Information
Contents
1. OLLON Service Manual UK English 17 of 172. 15 Installation and Door Reversal 16 INTRODUCTION The interior has one fruit and vegetable crisper with a glass cover four removable height adjustable shelves one hinged bottle rack The door has one removable door shelf with a lid an egg tray lidded butter dish two removable commodity shelves a compartment for a 2 litre bottle and one removable door shelf for bottles The HS2321L model is an over counter 216 litre larder fridge and is manufactured in Italy The product was launched November 2008 The HS2322L is the same as HS2321L and was launched March 2012 The electronic thermostat interior light and light switch are contained in the control box mounted in the top right hand side of the fridge Please refer to Technical Specifications for Climate Class and dimensions As with many refrigeration appliances it is important that it is installed and operated within the recommended ambient temperature range and that there is also adequate ventilation 4 of 17 Indesit TECHNICAL SPECIFICATIONS Colour Introduction Date Mode of Installation Door Hinging Dimensions Height Width Depth Weight Total Capacity Defrosting Climate Class Energy Consumption Energy Band Compressor Winding Resistances Mains Cable Length Electrical Supply Refrigerant Charge R600 Polar White HS2321L November 2008 HS2322L Marc
3. 5407691 Issue 1 Dec 2012 5 003482 C00291854 Hotpoint Built In Integrated Larder Fridges DD Models Covered HS2321L HS2322L Service Information Indesit Company UK Ltd 2012 Reg Office Peterborough PE2 9JB Registered in London 106725 Indesit HEALTH AND SAFETY For the servicing of refrigeration products containing Isobutane R600a refrigerant These instructions are in addition to any other Company procedures already published Published primarily for Indesit Company engineers working in the UK or Southern Ireland for which these instructions are MANDATORY 10 11 12 13 14 15 16 17 18 Only engineers who have been trained on the safe handling of Isobutane R600a refrigerant are authorised to transport store or carry out system repairs This manual is not intended as a comprehensive repair maintenance guide to the appliance Must only be used by suitably qualified persons having technical competence applicable product knowledge suitable tools and test equipment Servicing of electrical appliances must be undertaken with the appliance disconnected unplugged from the electrical supply Servicing must be preceded by earth continuity and insulation checks plus refrigerant leak detection Personal safety precautions must be taken to protect against accidents caused by sharp edges on metal and plastic parts After servicing the appliance must be rechecke
4. INSERT A VALID SMARTCARD RELATING TO THE MODEL amp MAIN POWER MODULE board TO BE PROGRAMMED INTO THE SMARTCARD READER check orientation of the smartcard chip Poor connection between the smartcard and smartcard reader INSERT THE SMARTCARD READER INTO EITHER THE SERIAL PORT OF THE POWER MODULE BOARD OR INTO THE LOW END ADAPTOR Version 2007 WHERE APPLICABLE RESOLVE THE PROBLEM FURTHER DIAGNOSTICS MAY BE REQUIRED ON THE APPLIANCE If the RED LED was flashing RAPIDLY check for the following e Ensure a smartcard was inserted into the smartcard reader e Ensure the smartcard was fully inserted RE CONNECT THE APPLIANCE TO THE ELECTRICAL SUPPLY GRID A STATIC RED LED WILL LIGHT UP TO SIGNAL THAT THE SMARTCARD READER IS SUPPLIED DISCONNECT THE SMARTCARD READER FROM THE APPLIANCE AND THE SMARTCARD FROM THE SMARTCARD READER IF THE RED LED IS FLASHING COMMUNICATION PROBLEM SMARTCARD INVALID ERASED DISCONNECT unplug THE APPLIANCE FROM THE ELECTRICAL SUPPLY grid IF THE DOWNLOAD FAILED THE SMARTCARD WOULD NOT HAVE BEEN ERASED IF THE RED LED IS STATIC fixed e DOWNLOAD HAS FAILED KO DOWNLOAD OK THE SMARTCARD CONTENT WILL BE AUTOMATICALLY ERASED Auedwog ys pul Indesit CONNECTING THE LOW END ADAPTOR 2007 Version with single and twin cable IMPORTANT 1 ALWAYS unplug the appliance from the mains electricity supply when connecting or disconnecting wiring on the module 2
5. ALWAYS connect the smart card reader or Hardware Key to the Low End Adaptor BEFORE connecting the adaptor to the module PCB connection L4 Ensure correct orientation of the pins 3 When using the converted Low End Adaptor with the twin cable ALWAYS insulate the open end of unused connector block with PVC tape to prevent it coming into contact with any other items before connection the mains supply The photos below only show the method of connecting the Low End Adaptor 2007 to the module connection L4 These photos do not show the other wiring connections for the appliance When connecting the low end adaptor to the module in the appliance you should temporarily reassemble the control box and make sure that it is safe before connecting the mains power supply Low End Adaptor Connector SS Connection L4 Ch Se Ge F Module Unused connector see text Smartcard Reader Key These photos show a 2007 Adaptor which has To avoid damage to the plastic smartcard been converted using C00275571 twin cable containing the programming file insert the smartcard reader into the Low End Adaptor 2007 Adaptors which have not been converted BEFORE inserting the smartcard may also be used to program the module Note Smartcards can only be used ONCE 14 of 17 Indesit shown for illustrative purposes only T Temperature BE cho select button hs Unprogrammed modules
6. ar construction lower than ground level boiler air inlet outlet or near any possible source of ignition continued 2 of 17 Indesit HEALTH AND SAFETY 19 20 21 Working with a naked flame i e soldering or brazing is forbidden Unless otherwise stated pipework connections must only be made using the Lokring coupling system Electronic leak detectors with high voltage tips must NOT be used with any Isobutane R600a All equipment used for this activity must be checked regularly and maintained in a safe working condition parts must be replaced as required Information Regarding Isobutane Canisters The maximum quantity of Isobutane an engineer should hold or store at any one time is two 1kg net aluminium canisters supplied individually as Part No C00218421 2602600 Canisters must be stored inside the aluminium case with the weighing scales for protection from possible damage and heat The aluminium case must NEVER be placed next to a heat source or in direct sunlight Isobutane must only be dispensed to the appliance from the 1kg net aluminium canister placed in an upright position on the weighing scales provided All used canisters must be a returned as scrap and therefore left out for the driver to collect and return for disposal Canisters must not be punctured or the internal valve damaged Before storing the canister it must have the extraction tap valve removed and the internal valve of the canister
7. checked for leakage using leak detector Leak Detector Part No C00222861 5700043 All used canisters and those found to be leaking should be exhausted to atmosphere to ensure they are emptied completely Refer to the following paragraph Refit the extraction tap if necessary open the tap and then invert the canister This must be done outside in open air away from buildings and ignition sources and complying with Item 18 on previous page 3 of 17 Indesit INDEX Health amp Safety RE RR RARO CR wee eee ee 2 3 Introduction EE 4 Technical Specifications 25 m 6 aac UR dpa a dos 5 sc RI MT r 6 Au utotest todd ad ARRA RE ERA XE AERE ROS wR we 7 Replacement Door Seals for Door 8 Replacing the light Bulbwis 22 66 0658 cesses dacs es hh RR RR RA Rau RAE 9 Module and Wiring Diagram 10 Programming EMIT 11 12 Programming Flowchart 13 Connecting the Low End 14 Module Light Sequences ics sou enr Er NE
8. d for electrical safety Smoking naked flames or operating gas and or electrical equipment including cordless power tools are forbidden within the storage area working area and vehicles used to transport Isobutane The carrying case for the scales and refrigerant must display a red flammability label Part Number 8100063 that should be visible and readable at all times The vehicle and storage area must be ventilated as far as is reasonably practicable and the aluminium case kept out of direct sunlight The storage temperature of Isobutane should not exceed 50 C The vehicle transporting Isobutane R600a refrigerant must display a Red Flammable Gas warning sticker Part No C00247960 8100063 Engineers should not wear clothes that are liable to cause static discharge electrostatic sparking Avoid working in small rooms Do not work in cellars Whenever possible move the appliance into a larger open area away from possible ignition sources Request the customer to turn off all other electrical and gas appliances in the near vicinity of the repair and note that it is done Customers should be advised to restrict activity within the near vicinity for a short time Isobutane refrigerant must be vented to atmosphere outside of the premises e g via open window through the clear plastic hose supplied Isobutane is heavier than air and must not be vented within 3 metres of the following sewer cover cellar drain or any simil
9. get the seal started 8 of 17 Indesit Company Replacing the Light Bulb To replace the light bulb in the refrigerator compartment 1 Pull out the mains plug from the electrical socket 2 Access the light bulb by removing the cover as indicated in the diagram below 3 Unscrew the faulty bulb 4 Replace it with a similar light bulb within the power range indicated on the cover 10 Watt or 15 Watt E Service Manual UK English 9 of 17 LV 4 OL WN 2 usiBua FZ frame resistor where Module and Wiring Diagram Alternating current Refrigerator light Motor fan Compressor PTC relay Circuit breaker Refrigerator light button magnetic reed switch Probe Start condenser where installed WI Siue DU NM ES Di Wie OUS L SoS i installed HS2321L HS2322L Auedwog ys pul Indesit Company This machine can be programmed via the Emit using a USB lead Part number C00222800 Hardware key Part number C00115587 and the Memwriter software Black Serial Hardware Key USB Serial Cable Other types of Cable are available Replacement pins for the Serial Hardware Key are available as Part No C00114723 Qty 1 For Hardware Key The Black Hardware Key and USB Serial Cable will be replaced with a new style Hardware Key and Cable which now has a USB connection It has shorter m
10. h 2012 Built In Integrated Doors are hinged on the Right Hand side as supplied The door is reversible Unpacked Packed Minimum Aperture 1224 mm 1290 mm 1225 mm 540 mm 590 mm 560 mm 550 mm 620 mm 550 mm 36 0 Kg 39 5 Kg Gross 216 litres Net 213 litres Automatic HS2321L N ST 16 C to 38 C HS2322L SN N ST T 10 C to 43 C HS2321L to 1998 Regulations 161 kWh year 0 44 kWh 24 hours HS2322L to 2011 Regulations 138 kWh year 0 38 kWh 24 hours HS2321L A HS2322L A Electrolux Embraco HTK70AA EMX26CLC Start 24 6 Ohms Run 28 1 Ohms Start 24 6 Ohms Run 28 1 Ohms 2 metres 240 Volts AC 50 Hz Refer to Rating Plate 5 of 17 Indesit Company OVERALL VIEW refer to illustration below dg Interior Lamp amp Cover switch Control Panel Set TEMPERATURE SUPER COOL Marcato Mgmt ADJUSTMENT indicator light button CONTROL PANEL Removable lidded shelf with EGG TRAY SHELVES Removable multipurpose SHELVESe Compartment for a 2 LITRE BOTTLE FRUIT and VEGETABLE bin BOTTLE shelf Varies by number and or position Available only on certain models Service Manual UK English 6 of 17 Indesit AUTOTEST MODE Autotest Function 4 Shown pushed in Light switch button 8 E 1 Super Cool LED 2 Te
11. he alarm and make the product switch to OFF state 7 of 17 Indesit REPLACEMENT DOOR SEALS FOR DOOR ASSEMBLIES Various types of door seal are supplied as replacements See Figs A B and C showing seal profiles Note also the liner profiles A5 A6 and B5 B6 below The door seal Fig A is retained by the liner which has 2 screws securing each corner The door seal as illustrated in Fig B is not available as a spare part but the seal as shown in Fig C is supplied as the replacement Remove the door from the appliance and place on a flat protected surface Cut the seal across each corner including the rigid tongue section retained by the liner Each section can then be withdrawn from the liner using snipe nosed pliers and pulling Where the seal is particularly tight in the liner slot it might be helpful to ease the edge of the liner away from the door panel using a wide bladed screwdriver or chisel knife Part No C00222502 5500012 Similar practice should be adopted when fitting the replacement seal Once the seal is removed and the liner seal pocket is empty it can be helpful to insert the chisel knife between the liner door panel and slide it around the door to clear any debris Fitting the Replacement Seal Insert the replacement door seal rigid tongue between the liner and door panel and push into position Fig B It may be necessary to insert a chisel knife between the liner and door panel to
12. mp LED s 3 Selector Button To start Autotest a With the Fridge Door open push and hold in the Light switch button light Off position See item 4 above b Press and hold the 3 key see above on the control panel for 5 seconds The test sequence will begin Autotest Sequence All LEDs on the control panel are off during the AUTOTEST procedure At the end of the AUTOTEST the appliance returns to the ON position at a temperature of 4 C Press the button on the control panel or unplug the appliance to stop the AUTOTEST procedure Step Duration Action Light M Notes 1 5 sec Pause OFF OFF If probe is faulty go to Step 3 2 1 sec Check probe OFF OFF If probe is OK go to Step 4 Interior 3 249 Activate AIR Fault light ON End of autotest procedure error message blinks 4 249 sec Activate AIR Probe ON ON OK message End of autotest procedure Alarm Messages There is only one alarm message NTC short circuited open Alarm on refrigerator light blinks The alarm is only signalled during the autotest Temperature Alarm The temperature alarm indicated by the flashing set temperature LED and a buzzer comes on automatically when the NTC probe measures a temperature of above 10 C for more than 30 minutes Reset Temperature Alarm If a temperature alarm has been generated press the ON OFF SET TEMPERATURE key the only key on the control panel to reset t
13. ore robust pins similar to those currently fitted into the SmartCard Reader It is not possible to mix old and new cables or keys NOTE The USB Hardware Key also supports a low voltage connection point which allows an external power supply to be connected to the Hardware Key which enables the main module to be programmed with a settings file prior to fitting it to an appliance This is NOT applicable to UK Service Engineers Do not connect anything to this connection point USB Cable C00289046 Low Voltage USB Connection Connection Point do NOT use Service Manual UK English 11 of 17 Indesit Compe MAIN BOARD PROGRAMMING NOTE The module does not have a physically replaceable EEProm Programming a Main Board eto There are a number of ways the board can be programmed some of which are not applicable to certain markets Types of programming 1 Handheld Terminal Not UK 2 Emit Memwriter UK Indesit Service Engineers 3 Smart Reader and Smart Card certain areas of UK market see Smart Card Indesit Comnany ma photo this card holds the i mera TE program file and can only be used ONCE NL Unst Bamas PROGRAMMING Using Smartcard Reader Card If the Main Module has been replaced during a repair the board will require programming using the fol lowing method 1 Do NOT connect the machine to electrical supply 2 Insert the pre programmed ca
14. rd into the Card reader Smart Card Reader Care must be taken at this point to ensure the card is and Smart Card in use inserted correctly with the Chip on the card facing the PCB of the Reader This example shows it connected to a 3 Insert the Reader and Card into module connection washing machine module connector port see photo 4 Connect the machine to the Electrical supply the LEDs on the Smart Card Reader will light in this sequence a Red ON Good Communication between Smart Card Reader and Card b Red OFF with Green Blinking Download taking place Do not unplug the appliance or any connections c Atend Green ON gt Download OK Go to 5 below d Atend Red ON or RED Flashing gt Download NOT OK 5 Programming Complete disconnect the machine from Electrical supply Smart will be erased and cannot be used again 6 Remove the Smart Card Reader See page 14 for connection details Restart the appliance 12 of 17 LV Jo l Mn Ienuey usiBua SMARTCARD PROGRAMMING PROCEDURE FLOWCHART DISCONNECT THE SMARTCARD READER FROM THE DISCONNECT unplug THE APPLIANCE FROM THE ELECTRICAL SUPPLY grid APPLIANCE AND THE SMARTCARD FROM THE SMARTCARD READER AND ACTION BELOW If the RED LED was flashing SLOWLY and a smartcard was inserted check for the following Invalid erased smartcard previously used Discard the invalid smartcard Incorrectly inserted smartcard
15. will have all 5 lights illuminated Note 5 i Pret a Service Modules are s supplied blank and will require programming See Programme L4 Low End Adaptor las Connection point L4 Programmed modules will have the middle light illuminated by default when powered up after programming Note Pressing the button will step through the LED positions one at a time from right to left then to the off position indicated by 3 beeps and all lights Off Further presses will repeat the sequence Shown in the Off state no lights illuminated The Off state is achieved by stepping through all the temperature options until all lights are Off The compressor will not run An appliance which is disconnected from the main supply will also look like this 15 of 17 Indesit INSTALLATION amp DOOR REVERSAL A KUP 100 676 680 KM 160 KUP 141 875 878 190 1018 1022 KM 230 KUP 200 1220 1224 1225 ATTENZIONE WARNING ATTENTION N 16 of 17 08 2009 195021555 07 Indesit Company L M
Download Pdf Manuals
Related Search