boom! audio 6.5 in front fairing speaker kit - Harley
Contents
1. death or serious injury remove main fuse before pro ceeding 00251b J05656 amp Many Harley Davidson Parts amp Accessories are made of plastics and metals which can be recycled See the service manual to remove the main fuse Turn ignition switch OFF REMOVAL 1 Remove the outer fairing and windshield per the service manual 2 See Figure 1 Remove the harness anchor 2 from each speaker enclosure 1 Retain all fasteners for installation 3 Unplug the speaker connector 3 on one enclosure 4 Right side only Unplug the power outlet connector C132B not shown Left side only CB equipped models Unplug the CB connector 184 4 and CB antenna See the service manual 5 Remove the three screws 6 securing the lower portion of the enclosure to the fairing support bracket 5 6 Remove two screws 8 securing the upper portion of the enclosure to the upper support bracket 7 NOTE Do not remove any of the screws 10 securing the speaker enclosure halves together 7 Remove three screws 9 securing the speaker enclosure to the inner fairing Remove the speaker enclosure from the vehicle 8 Remove four screws 12 to free the speaker 11 from the enclosure 9 Disconnect wires 13 Remove the speaker from the enclosure 10 Remove the three screws 15 securing the speaker grille 14 to the inner fairing Remove the speaker grille from the fairing 11 Repeat steps 3 10 to remove the rem2. aining speaker enclosure NOTE Never operate the vehicle with the speaker enclosures removed The enclosures provide important structural support to the fairing Operating without the enclosures in place can result in damage to the fairing assembly 1 of 3 Please dispose of materials responsibly is07432 Speaker enclosure Fairing harness anchor Speaker connector CB connector Fairing support bracket Upper support bracket Screw hex socket 1 4 20 x 1 2 in 13 mm long 2 Screw hex socket 1 4 20 x 3 4 in 19 mm long 3 10 DO NOT remove these screws 13 11 Original 5 1 4 in 133 mm speaker 12 Screw TORX 10 x 1 2 in 13 mm long 4 13 Speaker wire connectors 14 Speaker grille 15 Screw TORX 10 x 3 8 in 10 mm long 3 16 Alignment pin 17 View in direction of arrow OON DUA OND Screw hex head socket 5 16 18 x 3 4 in 19 mm long 3 Figure 1 Speaker Enclosure Removal Left Side Shown INSTALLATION NOTES See Figure 2 The new speaker grilles are side specific The shortest mounting tab A mounts to the inboard side of the opening in the fairing e Verify proper orientation of the Bar amp Shield emblem before proceeding 1 Install the correct speaker grille 2 or 3 from the kit into each side of the inner fairing Secure with three TORX screws Figure 1 Item 15 removed earlier Tighten to 9 13 in Ibs 1 0 1 4 Nm 2 See Figure 2 Rotate the speaker assemb
3. cMOTOR HARLEY DAVIDSON WY J05656 INSTRUCTIONS REV 2013 04 18 BOOM AUDIO 6 5 IN FRONT FAIRING SPEAKER KIT GENERAL Kit Number 76000317 Models For model fitment information see the P amp A retail catalog or the Parts and Accessories section of www harley davidson com English only NOTE The speakers in this kit are for use ONLY on specific 2014 and later Harley Davidson audio systems See the P amp A retail catalog or the Parts and Accessories section of www harley davidson com English only Using these speakers on 2005 or earlier Harley Davidson audio systems WILL permanently damage those systems Installation Requirements AWARNING The rider s safety depends upon the correct installation of this kit Use the appropriate service manual procedures If the procedure is not within your capabilities or you do not have the correct tools have a Harley Davidson dealer perform the installation Improper installation of this kit could result in death or serious injury 00333a NOTE This instruction sheet refers to service manual information A service manual for this year model motorcycle is required for this installation One is available from a Harley Davidson dealer Kit Contents See Figure 2 and Table 1 PREPARATION NOTE For vehicles equipped with security siren With security fob present turn ignition switch ON WARNING To prevent accidental vehicle start up which could cause
4. ly 1 so the tweeter bridge B is 45 degrees outboard from the top Verify that hole C in the speaker frame mates with the alignment pin Figure 1 inset Item 16 on the speaker enclosure Hole is marked B on left speaker A on right speaker J05656 3 Attach the speaker wire connectors 13 inside one of the speaker enclosures to the spade terminals on the back of the new speaker Different size spade contacts prevent improper assembly Install the speaker Secure with four TORX screws 12 removed earlier Tighten to 14 20 in lbs 1 6 2 3 Nm Install the speaker enclosure to the inner fairing Secure with three hex socket screws 9 removed earlier Tighten to 48 60 in Ibs 5 4 6 8 Nm Secure the lower portion of the enclosure to the fairing support bracket 5 with three hex head socket screws 6 removed earlier Tighten to 20 24 ft lbs 27 1 32 5 Nm Secure the enclosure to the upper support bracket with two hex socket screws 8 Tighten to 48 60 in lbs 5 4 6 8 Nm Repeat steps 2 7 with the remaining enclosure Mate the speaker and power outlet connectors Secure the harness anchors to the speaker enclosures 20f3 10 Left side only CB equipped models Plug in the CB connector 184 and CB antenna See the service manual COMPLETION NOTE To prevent possible damage to the sound system verify that the ignition is OFF before installing the main fuse 1 See the service manual to install the main fu
5. se 2 Turn the ignition ON but do not start the motorcycle NOTE Before installing outer fairing check that speakers are operating correctly Understand that buzzing squeaks and rattles may be heard until outer fairing is installed 3 Refer to the PREMIUM SOUND SYSTEM section of the owner s manual and turn the radio ON Make sure that all speakers are working and front rear fader function is operating correctly If not check speaker wiring 4 See the service manual to install the outer fairing and windshield WARNING After installing seat pull upward on seat to be sure it is locked in position While riding a loose seat can shift causing loss of control which could result in death or serious injury 00070b 5 See the service manual to install the seat IN USE Avoid direct contact with speaker grilles by a pressure washer Damage to speakers can result J05656 SERVICE PARTS is07433a Figure 2 Service Parts Boom Audio 6 5 in Front Fairing Speaker Kit Table 1 Service Parts Item Description Quantity Part Number 1 Speaker assembly 2 76000320 2 Woofer grille left 76000322 3 Woofer grille right 76000321 Item mentioned in text A Short mounting tab B Tweeter bridge C Alignment hole in speaker frame Marked A right speaker B left speaker 3of3
Download Pdf Manuals
Related Search