K4190B 52222B 2015 FORD F150 2WD LIFT KIT
Contents
1. 38 Install the front rotors on to the front hub 39 Install the front calipers on to the front rotors by reinstalling the retaining bolts Torque to factory specifications Install the tie rod end to the knuckle Torque to 111 ft Ibs 40 Repeat the installation on the other side of the vehicle 41 Reinstall the wheels and tires and lower the vehicle to the ground Torque the fac tory wheels to 150 ft Ibs If you are using aftermarket wheels follow the manufac turers recommended specifications 42 Torque the 18mm cam bolts to 180 200 ft Ibs 52222B Revised 7 25 15 43 Recheck all hardware for proper installa tion and torque at this time 44 On both sides of the vehicle check the routing of the brake lines and the ABS wire harnesses There must be no pinching rubbing or stretching of either component Use zip ties to secure these items At full droop cycle the steering from lock to lock while observing the reaction of these components Reposition them if needed IMPORTANT BE SURE TO BRING THE VEHICLE IMMEDIATELY TO A REPU TABLE ALIGNMENT SHOP TO BE ALIGNED IMPORTANT SOME 2WD LONG BED VERSIONS MAY NOT NEED TO HAVE THE STRUT SPACER SHIMS 91 5575 INSTALLED IF THE FRONT OF YOUR VEHICLE MEASURES LESS THAN 28 TALL FROM THE HUB CENTER LINE TO THE EDGE OF THE WHEEL WELL ADD STRUT SPACER SHIM 91 5575 TO ACHIEVE THE DESIGNED RIDE HEIGHT OF 28 1 2 3 8 IMPORTANT AFTER INSTALLA TION2. OF KIT AND BEFORE THE VEHICLE IS FIRST STARTED BE SURE TO CEN TER THE FRONT WHEELS AND THE STEERING WHEEL IF THE FRONT WHEELS AND THE STEERING WHEEL ARE NOT CENTERED BEFORE START ING THE VEHICLE IT MAY TRIGGER A DIAGNOSTIC TROUBLE CODE THAT WILL HAVE TO BE RESET BY THE MANUFACTURERS SERVICE FACILITY NOTE SEE PAGE 13 FOR STEER ING STOP ADJUSTMENT INSTRUCTIONS 52222B Revised 7 25 15 Rear Installation 1 Block the front tires and raise the rear axle pad making sure the pins are fitted of the vehicle Support the frame with into the holes on the spring perch Use jack stands forward of the rear springs your floor jack to raise the axle to the spring making sure the tabs on the spring block fit into the holes on the lift block 3 Remove the shocks on both sides of See Illustration 9 the vehicle It may be necessary that YOU 15 Secure the assembly with the U bolts slightly raise the axle to unload the 13 90390 supplied in hardware pack shocks for removal and new high nuts and washers from 4 Unbolt the emergency brake line mount hardware pack 20 65302 Do not 2 Remove the rear wheels from the frame Remove the OE bolt and tighten the U bolts at this time See Il clip nut from the frame and save for rein lustration 9 stallation NOTE Make sure the block sits 5 Bolt the emergency brake line drop flush on the axle perch bracket 91 10110 to the frame using the 14 Repeat the installation on the othe
3. on the brake lines or damage will occur 7 Remove the front rotors from the front hub 8 Disconnect the sway bar end links from the sway bar Save hardware for rein stallation 9 Unbolt and remove the sway bar from the vehicle Save hardware for reinstallation 10 Remove the tie rod end nut and separate from the knuckle using the appropriate tool 52222B Revised 7 25 15 11 Remove the upper ball joint nut from the knuckle and separate using the appropri ate tool 12 Remove the lower ball joint nut separate using the appropriate tool Remove the knuckle from the vehicle and set the knuckle aside 13 Remove the three OE nuts from the top of the strut assembly and the two OE nuts on the bottom Remove the strut assembly from the vehicle Save hard ware for reinstallation 14 Remove the two bolts that retain the lower a arms and remove them from the truck 15 Repeat on the other side of the vehicle 16 Remove the rear cross member brace retain the 4 OE bolts and nuts for rein stallation See Illustration 1 NOTE Careful heating of the OE bolts may be necessary to loosen the factory thread locker 17 Install the front cross member 91 5519 into original front A arm mounting loca tions using the factory bolts with the heads to the front leave loose See ll Illustration 1 OE Crossmember Brace Removal Frame OE Crossmember Uu ZU Brace Ps d 52222B Revised 7 25 15 Front Cr
4. tire of radial design not exceeding 35 tall X 13 5 wide is recommended Please note that the use of a 35 X 13 5 tire may require fender modification Violation of these recommendations will not be endorsed as acceptable by Pro Comp Suspension and will void any and all warranties either written or implied IMPORTANT 18 OR LARGER WHEELS MUST BE USED IN CONJUNCTION WITH THIS LIFT KIT 4 Front Installation 1 Prior to installing this kit with the vehicle on the ground Measure the height of your vehicle This measurement can be recorded from the center of the wheel straight up to the top of the inner fender lip Record the measurements below LF RF LR RR 2 Ensure that your work space is of ade quate size and the work surface is level Place the vehicle in park and set parking brake Place blocks both in front of and behind the rear wheels Place your floor jack under the front cross member and raise vehicle Place jack stands under the frame rails behind the front wheel wells and lower the frame onto the stands Remove the jack and remove the front wheels 3 Remove any skid plates if necessary 4 Work on one side of the vehicle at a time 5 Unbolt the OE brake line and bracket from the side of the knuckle Save the hardware for reinstallation 6 Remove the front caliper and bracket as sembly from the front knuckle by remov ing the 2 retaining bolts NOTE Make sure you do not let the calipers hang
5. 222B Revised 7 25 15 Illustration C Shim Installation Steering Stop Shims 5 16 X1 Bolts Steering Stop Shims Note This Illustration is just a representation and every application will be different 14 52222B Revise 7 25 15 Revision Page Use this only as a guide for hardware without a called out torque specification in the instruction manual Bolt Torque and ID Decimal System Metric System All Torques in Ft Lbs Maximums O 15 20 X MW6 5 939 t2 98 3 45 m 18 23 27 76 45 6 X Mi 32 45 S0 712 6 9 G2M2 55 765 90 S9ne 95 130 MM 85 120 145 1 88 135 175 Mdej 130 1 210 pA 185 200 ej 170 240 290 1 2 13x1 75 HHCS Grade 5 Grade8 M12 1 25x50 HHCS Qm A No of Marks 2 E G Grade Bolt Strength P Property Class Bolt Strength D Nominal Diameter Inches D Nominal Diameter M illimeters T Thread Count Threads per Inch T Thread Pitch Thread Width mm L Length Inches L Length Millimeters X Description Hex Head Cap Screw X Description Hex Head Cap Screw d 52222B Revised 7 25 15 The PRO COMP PROMISE WARRANTY At Pro Comp we know you have many choices when selecting products to personalize your vehicle You should demand nothing but the highest quality available and have total confidence that the products you selected are the best in the industry It is for these r
6. 400 W Artesia Blvd ee Compton CA 90220 Latest Revision Fax 310 747 3912 7 25 15 Ph 1 800 776 0767 E Mail info procompusa com Website www procompusa com LA off road driven PRO COMP SUSPENSION IMPORTANT 18 AND LARGER WHEEL NOT TO EXCEED 9 IN WIDTH WITH A MAXIMUM BACKSPACING OF 5 1 2 MUST BE USED IN CONJUNCTION WITH THIS LIFT KIT See pg 4 for details K4190B 52222B 2015 FORDF150 2WDLIFTKIT This document contains very important information that includes warranty information and instructions for resolving problems you may encounter Please keep it in the vehicle as a permanent record 52222B Revised 7 25 15 Box 1 of 4 PN 52222B 1 Part Description Qty Illus Page 91 10457 REAR CROSSMEMBER 1 3 4 6 91 10468 SWAY BAR DROP Drvr 1 4 6 95 300F 3 LIFT BLOCK 2 9 11 91 5574 REAR BUMP STOP DROP 4 10 12 91 5575 STRUT SPACER SHIM 2 7 8 90 6701 HARDWARE PACK Rear Crossmember 2 71 181502501000 18mm 2 5 X 150mm HEX BOLT 10 9 1 5 7 72 01810932 18mm 2 5 STOVER NUT Gr C 1 5 7 73 01810934 18mm USS FLAT WASHER 2 5 7 90 6703 HARDWARE PACK Leaf Spring Shim Pack 1 90 3085 FORD REAR END SHIMS 4 97 120 1 2 X 3 1 2 GR 8 USS HEX MACHINED HEAD 4 72 05010081 1 1 2 GR 8 USS UNPLATED HEX NUT 4 90 6314 HARDWARE PACK Rear Bump stop Drops 1 70 0311001800 5 16 X 1 HEX BOLT GR 8 1 72 031100816 5 16 STOVER NUT GR C 1 73 03100838 5 16 USS FLAT WASHER 2 70 0371501800 3 8
7. K Front Brake Lines 5 16 X 1 Gr 5 HEX BOLT 5 16 NYLOCK NUT 5 16 SAE FLAT WASHER HARDWARE PACK Sway Bar Drop 7 16 X 1 1 4 HEX BOLT Gr 8 7 16 STOVER NUT Gr C 7 16 SAE FLAT WASHER HARDWARE PACK Zip Ties ZIP TIE 11 BLACK HARDWARE PACK Cam Bolts CAM ECCENTRIC F 150 Slotted CAM BOLT Front 18mm 2 5 X 150mm 10 9 HARDWARE PACK Crossmember 18mm STOVER NUT 18mm FLAT WASHER HARDWARE PACK 9 16 HI NUTS Box 4 of 4 PN 52213B 4 9000 SERIES SHOCK STRUT SPACER HARDWARE PACK Spacer Mount 7 16 GR 8 HEX NUT 7 16 SAE FLAT WASHER 7 16 SPLIT LOCK WASHER Special Tools Please refer to your service manual for more information A special removal tool is required for safe removal of the tie rods PN T64P 3590 F These tool may be purchased at your local Ford dealer You may be able to rent any of these tools at your local parts store 3 Qty 1 AMD A R BHR S oR ADMD N O00 Illus 9 o CO an oan NNN 52222B Revised 7 25 15 Page 11 DAD NNN MMC MM o CO 9 9 9 9 52222B Revised Notice zur This installation requires a professional mechanic We recommend that you have access to a factory service manual for your vehicle to assist in the disassem bly and reassembly of your vehicle It contains a wealth of detailed information Prior to installation carefully inspect the vehicle s steering and driveline systems paying close atte
8. Torque to factory specifi top from hardware pack 90 6317 cations Torque to 45 50 ft Ibs See Illustration 7 30 Repeat steps 27 through 29 on the re maining side of the vehicle 29 Position the studs of the lower mount into the lower A arm and secure with the previously removed OE nuts See 31 Remove stock brake line bracket from frame Carefully remount the brackets with the supplied brake line drops 90 3202 drvr and pass in between bracket and frame Use factory hardware to fas ten the shorter end of the bracket to the frame Position the drops best for your application Use the supplied hardware from pack 90 6299 to fasten OE bracket to the new brake line drop WARNING Make sure the brake lines that you just modified are not rest ing against any moving parts 32 Support the lower A arms Position the new front knuckles Attach the knuckle to the lower ball joint Torque to 111 ft Ibs 33 Attach the knuckle to the upper ball joint Torque to 85 ft Ibs 34 Connect the anti lock wiring harness and sensor to the hub 35 Attach the OE dust shields to the knuckle using the previously removed OE bolts 36 Install the supplied brake line relocator 91 10106 to the upper hole in the knuckle with the hole facing downward using the previously removed OE bolt 37 Secure the OE brake line bracket on the front brake line to the new relocator 91 10106 using the 5 16 X 1 bolt and hardware
9. X 1 1 2 HEX BOLT GR 8 2 10 12 72 037100816 3 8 STOVER NUT GR C 2 10 12 73 03700034 3 8 HARDENED FLAT WASHER 4 10 12 90 6569 HARDWARE PACK Carrier Bearing Shim Kit 1 90 1080 3 8 SHIM 2 90 1081 1 4 SHIM 2 90 1082 1 8 SHIM 2 90 6013 HARDWARE PACK Carrier Bearing Shim Kit 1 70 04322501800 7 16 x 2 1 4 USS GRADE 8 BOLT 2 73 04300042 7 16 USS HARDENED WASHER 2 Box 2 of 4 PN 52221B 2 90 40032 KUCKLE Drvr 1 90 40033 KUCKLE Pass 1 90 6299 HARDWARE PACK Front Brake Lines 1 70 031 1001500 5 16 X 1 Gr 5 HEX BOLT 2 72 03100100512 5 16 NYLOCK NUT 2 73 03100030 5 16 SAE FLAT WASHER 4 91 10106 BRAKE LINE RELOCATOR Front Knuckle 2 Box 3 of 4 PN 52222B 3 91 10453 FRONT CROSSMEMBER 1 2 6 91 10471 SWAY BAR DROP Pass 1 4 6 6 7 13 90390 U BOLT 9 16 18 x 3 36 x 12 50 4 9 11 Part 4 91 10110 91 5502 90 6915 70 0371501800 72 037100816 73 03700034 90 6393 90 3202 90 6299 70 0311001500 72 03100100512 73 03100030 90 6340 70 0431751800 72 043100816 73 04300830 90 6319 10999 90 6751 90 5532 90 5533 90 6313 72 01810932 73 01810934 20 65302 932008 91 2977 90 6317 72 043200810 73 04300830 73 04300836 Description EMERGENCY BRAKE BRACKET REAR BRAKE LINE DROP HARDWARE PACK Brake Line Drop Bump Kit 3 8 X 1 HEX BOLT Gr 8 3 8 STOVER NUT Gr C 3 8 USS FLAT WASHER HARDWARE PACK Front Brake Line Drops F150 BRAKELINE DROP HARDWARE PAC
10. ad lock retaining compound where specified Please note that while every effort is made to ensure that the installation of your Pro Comp lift kit is a positive experience variations in construction and assembly in the vehicle manufacturing process will virtually ensure that some parts may seem difficult to install Additionally the current trend in manufacturing of vehicles results in a frame that is highly flexible and may shift slightly on disassembly prior to installation The use of pry bars and tapered punches for alignment is considered normal and usually does not indicate a faulty product However if you are uncertain about some aspect of the installation process please feel free to call our tech support department at the number listed on the cover page We do not recommend that you modify the Pro Comp parts in any way as this will void any warranty expressed or implied by the Pro Comp Suspension company If you use traction bars ES9000 shocks may hit the traction bar mount if it does a MX6 Series shock should be used Tire amp Wheel Information Due to differences in manufacturing dimensions and inflated measurements tire and wheel combinations should be test fit prior to installation Tire and wheel choice is crucial in assuring proper fit performance and the safety of your Pro Comp equipped vehicle For this application a 18 or larger wheel not to exceed 9 in width with a maximum backspacing of 5 1 2 is acceptable A quality
11. assem blies PN 91 5774 to the frame using the previously removed OE bolts See Illus tration 10 19 Insert the supplied sleeves 60859 in Illustration 9 Block install 95 300F Lift Block 52222B Revised 7 25 15 both end of the shocks 20 Install your new Pro Comp shocks MX6166 932008 or ZX2071 w shaft end up and torque this hardware to 66 ft lbs 21 Reinstall the wheels and tires and lower the vehicle to the ground 22 Reinstall the wheels and tires and lower the vehicle to the ground Torque the factory wheels to 150 ft Ibs If you are using aftermarket wheels follow the manufacturers recommended specifica tions U BOLT 13 90390 52222B Revised 7 25 15 NOTES On completion of the installation have the suspension and head lights re aligned After 100 miles recheck for proper torque on all newly installed hard lt lt ware es Recheck all hardware for tightness 91 5574 zx Pig ur Bump Stop dI after off road use Drop Halves Ns 2 OE Bump Stops 3 8 X 1 1 2 Bolt Illustration 10 Rear Bump Stop Drop Assembly NOTE If you wish to raise the ride height of the rear of the vehicle Install the rear leaf spring shims from hardware pack 90 6703 using the en closed instructions 23 Recheck all hardware for proper in stallation and torque at this time NOTE If driveshaft vibration oc curs install the carrier bearing shim kit 90 6569 using t
12. easons that Pro Comp Suspension products are backed by the best warranty in the industry the Pro Comp Promise Pro Comp promises that its products will last a lifetime or we will replace it free of charge It s that simple Because of our commitment to quality and manufacturing excellence we are able to stand behind our products FOREVER It is Pro Comp s Promise that if one of our suspension products breaks not due to misuse neglect or vandalism we will re place it Whether you are the original purchaser or not you can be assured that we will make it right The Pro Comp Promise covers all suspension products including shocks and steering stabilizers Buy Pro Comp Suspension today and enjoy it for the rest of your life That s our Pro Comp Promise Notice to Owner Operator Dealer and Installer Vehicles that have been enhanced for off road performance often have unique handling characteristics due to the higher center of gravity and larger tires This vehicle may handle react and stop differently than many passenger cars or unmodi fied vehicles both on and off road You must drive your vehicle safely Extreme care should always be taken to prevent ve hicle rollover or loss of control which can result in serious injury or even death Always avoid sudden sharp turns or abrupt maneuvers and allow more time and distance for braking Pro Comp reminds you to fasten your seat belts at all times and reduce speed We will gladly answer any questions c
13. he 3 8 X 1 1 2 bolts and hardware from pack 90 6013 Not all vehicles will use the same combination of shims Only by driving the vehicle and adding or re moving shims can the vibration be eliminated 12 Illustration A 52222B Revised 7 25 15 I Steering Stop Shim Adjustment Instructions PRO COMP SUSPENSIO Suspension Systems that Work After having the vehicle properly aligned by a qualified alignment shop ensure that your work space is of adequate size and the work surface is level Place the vehicle in park and set parking brake Place blocks both in front of and behind the rear wheels With the vehicle on the ground make sure the steering wheel and the tires are straight Turn the steering wheel to full lock left and remove the appropriate shims from the passenger side front stop and the driver side rear stop until the steering wheel at full lock is in the same position as Illustration A Turn the steering wheel to full lock right and remove the appropriate shims from the driver side front stop and the passenger side rear stop until the steering wheel at full lock is in the same position as Illustration B Be sure to use thread locking compound on the 5 16 X 1 shim retaining bolts See Illustration C Full Lock Left Full Lock Right Illustration B Full Lock Left Full Lock Right IMPORTANT Any more steering angle than shown in the illustrations may result in CV failure 13 52
14. ntion to the tie rod ends ball joints wheel bearing preload pitman and idler arm Additionally check steering to frame and suspension to frame attaching points for stress cracks The overall vehicle must be in excellent working condition Repair or replace all worn or damaged parts Read the instructions carefully and study the illustrations before attempting installation You may save your self a lot of extra work Check the parts and hardware against the parts list to assure that your kit is complete Separating parts ac cording to the areas where they will be used and placing the hardware with the brackets before you begin will save installation time Check the special equipment list and ensure the availability of these tools Secure and properly block vehicle prior to beginning installation Always use NEW cotter pins on re assembly These items are NOT supplied ALWAYS wear safety glasses when using power tools or working under the vehicle Use caution when cutting is required under the vehicle The factory undercoating is flammable Take appro priate precautions Have a fire extinguisher close at hand IT IS ADVISABLE THAT YOU HAVE HELP AVAILABLE WHEN INSTALLING THIS KIT SOME COMPO NENTS ARE HEAVY AND AWKWARD ADDITIONAL HELP IS GOOD INSURANCE AGAINST INJURY Foot pound torque readings are listed on the Torque Specifications chart at the end of the instructions These are to be used unless specifically directed otherwise Apply thre
15. oncerning the design function maintenance and correct use of our products Please make sure that the Dealer Installer explains and delivers all warning notices warranty forms and instruction sheets included with Pro Comp product Warranty and Return Policy Pro Comp warranties its full line of products to be free from defects in workmanship and materials for the life of the product Pro Comp s obligation under this warranty is limited to repair or replacement at Pro Comp s option of the defective product Any and all costs of removal installation freight or incidental or consequential damages are expressly excluded from this warranty Pro Comp is not responsible for damages and or warranty of other vehicle parts related or non related to the in stallation of Pro Comp product A consumer who makes the decision to modify his vehicle with aftermarket components of any kind will assume all risk and responsibility for potential damages incurred as a result of their chosen modifications War ranty coverage does not include consumer opinions regarding ride comfort fitment and design Warranty claims can be made directly with Pro Comp or at any factory authorized Pro Comp dealer IMPORTANT To validate the warranty on this purchase please be sure to mail in the warranty card Claims not covered under warranty Parts subject to normal wear this includes bushings bump stops ball joints tie rod ends and heim joints Finish after 90 days Damage ca
16. ossmember Rear Crossmember Install Install 91 10457 Rear Crossmember lustration 2 Leave the bolts loose See Illustration 18 Raise the rear crossmember 91 10457 3 into place and install the 4 OE cross 19 Install the sway bar drop brackets 91 member support brace bolts into the 4 10468 drvr and 91 10471 pass using crossmember brace holes on the drvr the supplied 18mm X 150mm crossmem and pass side of the rear crossmember ber bolts Install the bolts with the heads Illustration 4 91 10468 J 716 X1 Sway Bar Drop Sway Bar i 1 4 Bolt Bracket Install Drop drvr 91 10471 Sway Bar Drop Pass 91 10457 Rear Crossmember SN 18mm X 150mm Bolt 52222B Revised 7 25 15 lllustration5 Ll d Fe Illustration 4 A Arm Install bu M ON ke 2M 2 Install the lower a arms into the new cross members with the supplied cam bolts 90 5533 cam eccentric 90 5532 18mm washers and nuts The cams should fit between the cam guides on the cross members Center the cams in the guides You will torque the bolts at the end of the install when the vehicle is on the ground See Illustration 5 22 Torque all crossmember and sway bar hardware according to the torque chart on page 15 or to manufacturers specifica tions 23 Transfer all the parts except the OE dust shields from the factory knuckles to the supplied Pro Comp knuckles 90 40032 drvr and 90 40033 pass NOTE Tighten all the fac
17. r supplied 3 8 X 1 bolt and hardware See side of the vehicle Illustration 8 15 When the installation of the remaining 6 Secure te OF Emergency brake line side is complete torque the U bolts to mount to the emergency brake line drop bracket 91 10110 using the previously re 105 ft lbs moved OE bolt and clip nut See Illustra 16 Remove the factory bump stops from tion 8 the vehicle Save the bolts for reinstalla 7 On drivers side unbolt the existing brake tion line bracket from the frame 8 Install the supplied brake line extension bracket 90 5502 to the frame using the previously removed OE hardware Then bolt the factory bracket to the new bracket TAE using the supplied 5 16 X 1 hardware peu from hardware pack 90 6314 9 Reroute rear ABS as necessary use the supplies zip ties to secure lines 10 Support the rear axle with a floor jack and remove the U bolts on the driver side Loosen the U bolts on the passen ger side 11 Remove the factory lift block from the spring assembly This will not be rein stalled 12 Install the lift block 95 300F onto the Scy id orm 10 17 Assemble the bump stop drop halves PN 91 5774 and install the OE bump stops to the bump stop drop assemblies using the supplied 3 8 X 1 1 2 bolts See Illustration 10 NOTE Be sure that the pins on the OE bump stops fit into the holes in the bump stop drop assemblies 18 Install the bump stop drop
18. tory hard ware carefully Be sure to follow the factory assembly procedures and torque specifications to the front Leave the bolts loose See Illustration 4 20 Secure the sway bar drop brackets 91 24 5565 drvr and 91 5518 pass to the OE sway bar mounting holes in the frame us ing the supplied 7 16 X 1 3 4 bolts and hardware Leave the bolts loose See Install the sway bar frame mounts to the sway bar drop brackets using the previ ously removed OE bolt plate and hard ware See Illustration 6 25 Secure the sway bar end links to the sway bar using the previously removed 91 10471 OE hardware Sway Bar Drop Pass 26 Torque the sway bar mount hardware to 60 ft lbs vns lt V LF 27 WITH THE STRUT SPACERS attach e w ANC UT the spacer 91 2977 to the top of the OE SN BN N strut assembly using the previously re moved OE hardware See Illustration 7 NOTE The notch in the bottom ring will face toward the rear of the ve hicle on the driver side and toward the front of the vehicle on the passenger side 28 For additional lift install the strut spacer shim 91 5575 onto the strut spacer 91 Ll 2977 studs and install the strut assembly Illustration 6 Sway Bar Install into the strut mounting locations Secure 52222B Revised 7 25 15 90 6317 Illustration 7 7 16 With strut spacer Hardware ZX2069 Coil Over Shock using the 7 16 supplied hardware on the Illustration 7
19. used as a result of not following recommendations or requirements called out in the installation manuals Pro Comp MX Series coil over shocks are considered a serviceable shock with a one year warranty against leakage only Rebuild service and replacement parts will be available and sold separately by Pro Comp Contact Pro Comp for specific service charges Pro Comp accepts no responsibility for any altered product improper installation lack of or improper main tenance or improper use of our products E Mail info procompusa com PLACE Website www procompusa com WARRANTY REGISTRATION Fax 310 747 3912 Ph 1 800 776 0767 NUMBER 16 HERE
Download Pdf Manuals
Related Search