Eng - ARK Design USA
Contents
1. Installation for relay box Caution the splices have to be insulated 1 Detaching the negative terminal from the battery 2 Disconnecting the connector from the key cylinder and connecting the timer harness depends on the vehicle model some key cylinder would have CARRIED coupler 3 Connecting the timer harness to the 3 terminals coupler of relay box 4 Connecting the while wire of relay box O2 sensor signal to the O2 sensor signal of ECU by splice 5 Connecting the black wire of relay box earth to the ECU control earth by splice 6 Connection the grey wire of relay box to hand brake by splice It will be OV when key is on at the parking brake position and it will be 12V when tt is disengaged Please check the parking brake switch before making the connection 7 Using the cable tie to fix the relay box and harnesses to avoid driving interference Please refer to individual vehicle circuit layout for O2 sensor signal and earth terminal position If it is not stated in the specific vehicle circuit layout please refer to the service manual general circuit layout In the case when simple A F display and post idling time do not automatically calculated connecting the additional WAKUGATA terminal to earth and ensuring the body earth is properly connected Installation for control box 1 Using the enclosed double sided tape to attach the control box 2 Connecting the control box harness to relay box using the ca2. minimum time set will be f the timer opeg hion time Decrease time Factory default is set to 5 min it displays as 5 00 changes per 0 05 gt Gs 5 sec to set the maximum time E MAbout Economical Driving EO E Petrol and air mix is the power for the petrol engine The ratio of mixed air to air is normally called the air flow ratio A F The normal ideal air flow ratio is about 14 7 when acceleration and greater engine output is required the output air flow ratio is about 12 5 For the economical engine during idling when no output required the A F is about 16 When engine is in motion there is a limitation for A F sometimes without a knowing reason the petrol is consumed without great horse power output that could be the reason of high petrol consumption By monitoring A F to keep the Aye Fae tays above 14 the driver can adjust by the ht acceleration HOH PoE Tre is needed which also reduce the load on indicatin simple A F while driving VOL TMode RPM light on indicating ito respond to the numerical VOLT light on indicating battery engine rev while driving x 10rpm numerical display 7 segment 1 is 10rpm 10 is 100rpm 100 is 1000rpm 999 is 9990rpm value LED colour changes voltage while driving A F below 11 value display 7 segments purple decimal points flashing flashes when below 10 0 A F 11 0 12 0 V purple red 10 0 is 10 0V A F 12 0 13 0 12
3. 0 is 12 0V red orange 16 0 is 16 0V A F 13 0 14 0 orange HHF flashes when above 16V green A F 14 0 16 0 green to light blue A F 16 0 18 0 light blue to blue 0 10 is 10 sec RPM decimal points flashing Full colour LED is normally showing the simple A F by changing its colour when change to shift rev setting whiltk colour flashes When simple A F not in display if long push the right switch the display turns off The white shjift light still flashes even when the display is off When do not want the white flashing light please set the revi fto a zone that would not be used VehicleECUPinout FR 00 2 00 2 00 10 05 1 99 10 05 1 01 12 05 1 99 1 01 11 99 8 02 7 99 8 02 7 93 10 99 9 89 10 93 9 89 10 93 9 95 5 05 6 91 6 95 4 89 5 91 5 LUA 94 2 99 8 99 9 99 9 AMT 4 F 97 9 02 8 97 9 02 8 FUTIYIS 98 10 x 7 1I 96 9 00 9 LUA 97 8 02 8 97 8 02 8 JIFUT 4Z 89 7 00 8 99 1 02 8 01 5 Only representative models are stated for other models please refer to the service manual Ht IyyVyat Jam ECU NCP31 35 INZ FE NCP30 2NZ FE NCP13 NCP10 15 2NZ FE SCP10 1SZ FE FA EA RY THE SCP10 NCP21 25 1NZ FE NCP20 2NZ FE SW20 SW20 SW20 E AE111 4AGE AE101 4A GZE AE92 4A GZE 1205 3S GTE 27231 222 GE E gil L 21230 1Z2 GE Eg ib L ST215M 3S GTE 3 ST2156 3S GE 3 SXE10 3S GE Eg i L JZX100 1JZ GTE 2 E JZST61 2JZ GTE Egi h
4. 15 JZS160 2JZ GT Egi hA T5 Z32 R34 R34 98 12 R33 98 4 98 4 99 1 02 7 99 1 02 7 R33 R33 S15 S15 96 6 98 12 S14 93 10 96 5 S14 93 10 98 12 S14 180SX 96 8 98 12 PRS13 SR20DET 96 8 98 12 _PRS13 SR20DE J4 YyYFA R 05 11 05 5 05 1 05 8 02 9 01 6 01 12 98 9 00 8 97 8 98 8 95 9 00 8 01 7 95 9 01 6 03 5 01 5 03 4 98 6 01 4 02 5 00 10 00 8 98 9 00 7 02 2 98 9 02 1 03 1 NY12 YZ11 E11 YK12 Td VG30DETT N2 RB26DETT RB25DET RB26DETT RB25DET RB25DE HR15DE HR15DE HR15DE HR15DE GD3 4 L15A EP3 EK9 EK9 EK4 DCS DC2 GD1 2 L13A 4 K20A K20A B18 MT BL BP5 EJ20 TB BH BE5 EJ20 6 8 BH BE5 EJ20 6 8 GDB GD GG B GD GG A 98 9 00 10 GC GF 8 GC GF 8 SG5 SFO CT9A 01 2 02 12 CT9A 96 8 01 1 92 11 96 7 95 10 91 10 95 9 91 10 95 9 94 1 00 5 CP9A CE9A CMSA CD5A 4G63 4G63 4G63 4G63 4G93 4G93 CA CB CC 4A 4G92 CDSW 4693 1 AD 94 9 97 10 N23W G 4G63 Mi RVR 92 10 97 10 N13W 23W 4G63 Mi 97 11 02 8 NYVTALA 00 6 00 6 98 8 00 5 RX 95 12 03 1 N61 71W 4693 H76W 4693 H62 67 72 W 4694 H66 76 W 4G93 FD3S 91 11 95 12 FD3S 00 7 05 7 02 7 05 7 95 8 97 11 97 12 00 6 97 12 02 6 89 9 93 7 93 8 95 7 NB8C NB6C NA8C NB8C About Engine Rev Auto Detection 13B REW signal input switch to 1 Top section of relay box This product is utilis
5. Warranty rules This warranty states important information in regards to the warranty please read all information 1 If the product is malfunctioned please contact the retail shop where the product was purchased 2When sending the product for repair please send this warranty together with the description of malfunction retail shop name and purchase date to the retail shop 3 Further the repair will be charged in the following condition even within the warranty period Ff the product was not used as prescribed in the manual or unusual usage which has caused the failure 11 Operation Switching Between Display and Setting Two length of pushes to switch between display and setting Short push below 1 sec and long push more than 2 sec This manual only states long push short push operation not Caution e Please do not operate the device while vehicle in motion Operation could cause disruption and stated accidents When timer operation not ON OFE Vey required please set to OFF mode in this case no information displayed Switch Operation Count Down q gt Competed TimerOn Dow decrease time EngineSTOP roller L switch OBS pg EG Ate 6a It is a sew saw be scrolled switch which up and down operates either ith a centre push to right or left select desired item S Prun M Rizh NY TIME wf NY m 5 i 3 fr NY 4 Setting cylinddr volume set between 2 to
6. understanding which achieves environmental friendly driving and economical energy consumption Post idling function 1 Auto accumulative mode it calculates the post idling timing from the prior engine TORQUE without wasting the energy Manual mode the post idling is performed based on the defaulted value or set up during the operation Rev Shift Timing display function 2 l The pulse from alternator was detected without connecting to rev signal line The light flashes to show the shift up to represent the rev and rev set up Simple A F E aa 3 rae Based on the JIRUKONIA type O2 sensor signal line distribution the E A F value is displayed According to the A F value full colour LE oane which shows the engine TORQUE and fuel consumption Battery voltage display function l Based on the display of battery voltage the battery level and status can be monitored Safety function Based on the connection to the PARKING brake signal line it prevents driving from its operation Large LED display Does not easily disrupted by surrounding situation the large LED can ensure its clear vision D 1 3 When the vehicle is not fitted with O2 sensor JIRUKOA type nor sensor is easily degraded some function or display may not be operated properly ae 2 The rev reading may not be displayed properly in some vehicles In that situation connecting the rev signal line could resume the display Content 1 Safety Notes 6 Installation Confirma
7. 8 cyl ilnd Left fr i 23444648 VOLT moving order i T When the A F ratio picked up from 02 sensor is incorrect Set the correct voltage point dEF at dEF the setting 4 Correction for Simple A I 010 long 20 0 short to factory defult correction can be performed Ls G retunn RPM 032 190i A F 041 18 0 065 16 0 MA When A F displayed Set Rev when shift light starts flashing a correct the voltage by When shift light starts flashing 35 130 OC set the rev in 100 rpm unit 906 12 0 display is set to every 10 rpm 936 11 0 o pet 983 10 0 A Decrease Rev A F Timer Mode Timer light on indicate timer time while driving Set Rev when shift light on When shift light is on set the rev in 100 rpm unit Display ils At manual mode it displays set it ime set to every 10 rpm so it willl At auto mode it displays C in 10 rpm units calculated time Increase Rev D R numerical display f Dow ecrease Rev Tsegments 0 00 is 0 sec 1 00 is 1 min 9 60 is 10 mins S II change in 10 rpm uni ts dEF Ga at dEF etting returns correction mode Increase Rev fa 2 L Dow gt GE After correction exit i OZE VY AER IRA SATURA lentes AR CEBUMBSIL RFRA DILAD RARLTHVNECA Force quit Timer OFF Engine STOP gt Increase setting time Ddcrease se
8. LIA AR DENION Installation Manual REV SHIFT Theat Product Name Rev Shift Timer Product Number 101A 001 type BLUE 101A 002 type RED Application Display vehicle engine rev heater and post idling Suit for Vehicle with DC12V body earth battery Introduction Thank you very much for purchasing Rev Shift Timer This manual is for the user to reference when using this product as well as for the installation Please read it carefully and use this product correctly after understand its functions and using conditions A provide this manual to the end user ote Ark Design reserves the right to change the specification price appearance etc in the Rev Shift Timer and its manual without prior notices When any modification is made to this product the warranty is void immediately and no responsibility will be taken Ark Design does not take any responsibility when the Rev Shift Timer and its accessories have been used in unspecified location or method which does not matter the damage was caused by the end user or other parties Ark Design does not take any responsibility when the damage occurred to the vehicle and its parts during installation Ark Design does not take any responsibility for the effects resulted from using the Rev Shift Timer such as engine trouble or incapable of using this product The Rev Shift Timer has following displays and functions The engine INITIATE BURDON to be shown clearly for easy
9. ble tie to fix harnesses to avoid driving interference The vehicle time and audio etc memories would be changed during the installation please reset to their previous setting alternatives 6 Installation Confirmation After the installation is confirmed please perform all functional checks 1 Please check if the following installation works have been completed a The bolts and nuts detached duning installation have been attached to their original position b There is no interference among the installed parts harnesses and any other car parts c Control box relay box and all harnesses have been affixed to avoid driving interferences d There is no mistaken connection made all connections are insulated properly e The battery negative has been connected 2 Starting the engine to confirm perform all functional checks A Safety function confirmation a Starting the engine and set the timer to anytime more than 30 seconds b Checking that the hand brake is on c Confirming that the timer starts function when key is at OFF position d During the count down if the brake is pressed and hand brake is disengaged timer should stop and the engine should be stopped B Engine rev reading confirmation a Checking if the relay box input circuit switching switch is in 1 situation 1 b Setting the cylinder reading at control box operation Refer to the method ON THE OTHER PAGE c Setting the rev reading at control box d
10. cause the engine to stop such as small litre vehicles in that case additional stall prevention kit is required Please check all the parts listed are correct and included before installation 1 Control box quantity 1 6 Splice quantity 4 2 Relay box quantity 1 7 Manual quantity 1 3 Cable tie quantity 2 8 Circuit layout quantity 1 4 Double sided tape quantity 1 9 Serial number sticker quantity 1 5 KUWAGATA terminal quantity 1 to be stuck on the Warranty 3 Control Box Full colour LED white colour flashes when SHIFT LAMP rotation setting changes For simple A F display the LED colour changes according to the A F Right left rocking switch to switch between the displays or selecting the setting menu use the switch to browse the Setting items when such item is displayed or in setting such LED is on Roll and push switch to switch between the displays or selecting the setting menu use the up and down roller to browse the alternatives and push the switch to set 7 Segment LED 4 Circurt Layout timer harness vehicle harness key cylinder grey to hand brake switch green to ROTATION signal line connect to ECU harness etc white to O2 sensor signal line connect to ECU harness etc connect to ECU earth when using O2 sensor signal connect to body earth when O2 sensor not in use use the included KUWAGATA terminal instead A ARE Gen 5 Installation
11. ing the weak noise in power line together with simple harness to display the engine rev However depends on the vehicle model sometimes the engine rev cannot be read due to noise wave form In that case please adjust the volume in the relay box side to display the engine rev Further scattered display could happen at the moment of powered on it is not a fault If the engine rev is still not in display please take a harness from ECU and connect to the rev signal line thin green wire and switch the rev Adjust volume O W Use a fine driver to change the volume to right or left to dectect the engine rev and set ECU location 1 Below the driver seat dashboard 2 Right on top or below the centre console 3 Above or below the glove box 4 Passenger seat cowl side 5 Underneath the carpert of passenger seat Note the pinout below are viewing from pin insertion side I J DIFI ZILI isa cl eA l N3 EO et ys PEELLLLt __ SCO LOCC OO C HOR Ti AT A A E eee naa E a e HHH n i1 E A UAA K Lir LU ALUO MA III Orr A EO 02 sensor
12. iring and components Hi Please stop using the product immediately when noise and or smell has occurred When usage continues it is possible to cause fire wire harness engine or vehicle damage If the above happens please enquire to the distributor or Ark Design Mi Please be cautious not to damage the wire harness or pipes duringinstallation Electrical short could cause fire damage to wiring and components Mi Please be cautious not to drop or shock the product It could cause malfunction accident fire electric shock damage to the wire harness and components W The installation must be done by professionals The installation needs professional knowledge to perform Mi Please be cautious not to lose or damage the original components when detach them during the installation Ark Design does not take any responsibility for the damage during the installation Mi Please use the appropriate tool to tighten up the bolts and nuts The screw section of the bolt could be damage when more than required torque is applied Note for Installation When timer is in use the following function may not be functional in the vehicles with remote control starter auto light system wireless door lock micro computer preset driving position system LIA vehicle harness needs to be prepared separately when installing Also when using the turbo timer depends on the voltage drop in the vehicle side when the key is turned to OFF some vehicle models could
13. isplay checking if the rev reading goes up together as the TACHO meter in the vehicle when accelerating slowly In the vehicle without a TACHO meter check the idling rev reading changes smoothly when accelerating slowly LJSome vehicles cannot take the engine rev reading from the alternator pulse In this case please rework the hamess to the ECU rotation signal line as below 1 Detaching the battery negative terminal 2 Connecting the green wire in relay box to the rotation signal line in ECU by splice 3 Using the cable tie to fix the hamesses to avoid driving interference 4 Checking if the relay box input circuit switching switch is in 2 situation 1 5 Connecting the battery terminal When completed please following step B above to check the rev reading function Please refer to the individual vehicle circuit layout for rotation signal pin out 1 Side view of relay box Connector for control box When not using the green wire in rotation Signal input switching switch take 1 When connecting the green wire to ECU rotation signal wire take O I e Please SLIDE the dimples in the switch C OS 7 Troubleshooting When the timer is not function as normal please refer to the following to reconfirm the circuit layout and connection Q When the key is ON there is no display on the control box A It is possible to be at OFF mode connection failure or the earth line is not connected properly Q the co
14. ntrol box is constantly in display does not matter itis nkey ON or OFF status A It is possible that the green wire thick wire is constantly connected to power Q The engine stops together with the key off A It is possible to be caused by following The time is set to 0 second Hand brake is not on properly safety function Low battery caused low voltage The green wire is not connected properly Timer hamess connection is failed Q Rev reading and simple A F display are abnormal A When the rev reading is failed please refer to 6 Installation Confirmation When the A F display is failed it is possible to be the O2 sensor type is different sensor degraded rapidly or the hamess connections have failed Application of splice p ai Taking 5 8 mm skin off the hamesses to be connected A OS Wrapping the connecting hamess Using the splice to cover the to the hamess to be connected connection w Pulling the connected wire lightly to check the hamesses are CLIMPED securely Using the electrical CLIIMPER to CLIMP the splice properly wrapping the connection properly for insulation 8 About This Manual Manual no 101A Z01 Issue date June 2006 Version 1 The specification price and appearance of this manual could be revised without prior notice 9 Warranty When the product is used in tts normal operation and failure occurs due to manufacturing issues within the warranty period one
15. tion Warning 7 Troubleshooting Caution 8 About This Manual Parts List 9 Warranty 10 Contact Us 11 Operation the other side of the page Control Section Installation Layout Installation 1 Safety Notes Wording explanation Warnin This word is used to show if the warning is ignored or operated wrongly it could B cause death or serious injury to the operator or third party This word is used to show if the caution is ignored or operated wrongly it could Caution cause middle or minor injury to the operator or third party NPON W Please do not dissemble modify or repair the product W Please do not fit this product to other than vehicle model specified Warranty is void when fitted into unsuitable vehicles Further it could caused unexpected damage to the vehicle please do not fit to the unsuitable vehicles Mi Please do not use the product other than specified Ark Design does not take any responsibility for the user nor the third party when damages occurred Mi Please affix the product and do not locate it in the location could affect driving or rattling When it is affecting driving it could cause accident Mi Please detach the negative terminal of the battery before installation Electrical short could cause fire damage to wiring and components Mi Please do not pull the wire harness when detaching the connector the connector has to be hold when detach Electrical short could cause fire damage to w
16. tting time 5 sec per setting unit between 0 10 mins increase time Timer mode setting gt Right display set time aig A U display Manual time setting modk 5 sec per setting unit between Auto accumulative calculation p lt gt increase time se e Depends on the engine status f Dow decrease tite the operation calculation can be selected from Xfactory default is set to 3 mins large H medium S small Ll mm a gt H 1044S 104L 10 setting order Y Dow at 10 min setting time is displayed 4 P About automatic calculation 5 Yel Her REEing unit betwegade petting A F Correctio 4 Viode 0 to 1 min The automatic calculation is based Hor pase Pe on engine rev and simple A F The value calculated multiply the Cc Decrease time coefficient set at H S L is the timer time When the rev is low when set S it displays S10 the 10 and engine is less loaded the increases decreases to show min set calcuated time will be minimum time when the rev is high and the load is heavy the calculated time will be increased In the case that 02 sensor is not y connected the engine rev is used to calculate time when engine rev Set the maximum time cannot be detected simple A F is used Bee Er RSPEI ng unit betwedm the case that neither engine 0 to 10 mins rev nor 02 sensor is connected no inerensestinc automat ic N4 Eeu at ion will be performed
17. year from date of purchase the product will be repaired without charge per stated in manual The warranty will not be reissued in any circumstances please keep it securely 10 Contact Us ARK DESIGN Co Ltd 7192 0362 32 5 MATUKI HACHIOUKI TOKYO JAPAN http www arkdesign co jp Product name Rev Shift Timer Thank you for purchasing the Rev Shift Timer Under the normal usage when a failure occurred due to manufacturing issues Ark Design will repair the failure without charge within the warranty period which is one year from the date of the purchase Please attach the warranty to the shop this product is purchased Warranty period One year from the date of the purchase to retail shops Please fill in the purchase date manufacturing number odometer and retail shop details with shop stamp in this warranty card If the information is missing the repair will still be charged during the warranty pernod Thank you for your understanding Purchasing date please affix the included serial seal here Vehicle odometer at installation Retail Shop It is mandatory to stamp the shop stamp and telephone number To the end customer Please reconfirm all information is filled when receiving this warranty card if there is information missing please contact your retail shop immediately Vehicle odometer at installation Vehicle name Engine type Year End customer address End customer telephone number End customer name
Download Pdf Manuals
Related Search