Micro 13 Service - Hitekfloorsupply.com
Contents
1. P100186 12 9097511000 1 2008 04 Micromatic 13E SERVICE MANUAL ENGLISH SOLUTION SYSTEM TROUBLESHOOTING Small amount of solution or no solution reaches the brush Possible causes 1 solution filter 25 is clogged dirty clean 2 hose 17 is disconnected from the quick coupling or it is broken connect or replace the hose 3 The quick coupling 11 or 39 is not installed properly check and install properly 4 solution pump 38 is broken or there is an open the electrical connection replace the solution pump repair the electrical connection 5 There is debris in the solution tank 14 clogging the filter clean the tank 6 There is debris in the detergent hose 17 or 31 clogging the detergent flow clean the hose 7 check valve 22 is faulty replace 8 There is dirt on the brush holes clean the solution holes Micromatic 13E 9097511000 1 2008 04 13 ENGLISH SERVICE MANUAL SOLUTION SYSTEM 14 9097511000 1 2008 04 Micromatic 13E SERVICE MANUAL ENGLISH BRUSH DECK SYSTEM BRUSH MOTOR ELECTRICAL INPUT CHECK WARNING This procedure must be performed by qualified personnel only 1 Drain the solution tank 142. P100189 Micromatic 13E 9097511000 1 2008 04 17 ENGLISH SERVICE MANUAL BRUSH DECK SYSTEM TROUBLESHOOTING The brushes turn slowly Possible causes 1 transmission system is dirty clean brush rotation shafts flanges and pulleys 2 motor 37 is overloaded clean the transmission system 3 driving belt 33 is loose adjust All brushes do not turn Possible causes 1 power supply cable is broken replace The pickup condenser 36 is broken replace The motor 37 is faulty repair or replace The main switch 6 is broken replace The program selection knob 5 is broken replace The driving belt 33 is damaged replace 18 9097511000 1 2008 04 Micromatic 13E SERVICE MANUAL ENGLISH RECOVERY WATER SYSTEM RECOVERY SYSTEM CLEANING 1 Drive the machine to the appointed disposal area 2 Make sure that the power supply cable 10 is disconnected from the electrical mains 3 Lift the solution tank 14a and if necessary drain it and clean it as shown the User Manual 4 Open the transparent cover A and clean it with care Clean the vacuum grid B with care Empty and clean the recovery tank 16 as shown in the User Manual Check the transparent cover gasket C
3. 30 Micromatic 13E 9097511000 1 2008 04 1 ENGLISH SERVICE MANUAL GENERAL INFORMATION CONVENTIONS Forward backward front rear left or right are intended with reference to the operator s position that is to say in operating position with the hands on the handlebar MACHINE LIFTING WARNING Do not work under the lifted machine without supporting it with safety stands MACHINE TRANSPORTATION WARNING Before transporting the machine make sure that All covers are closed The machine is securely fastened to the means of transport OTHER REFERENCE MANUALS The following manuals are available at Nilfisk Literature Service Department User Manual Micromatic 13E Form Number 9097508000 Spare Parts List Micromatic 13E Form Number 9097509000 SAFETY The following symbols indicate potentially dangerous situations Always read this information carefully and take all necessary precautions to safeguard people and property DANGER It indicates a dangerous situation with risk of death for the operator WARNING It indicates a potential risk of injury for people CAUTION It indicates a caution or a remark related to important or useful functions Pay careful attention to the paragraphs marked by this symbol NOTE It indicates a remark related to importa
4. 13 BRUSH DECK SYSTEM 15 BRUSH MOTOR ELECTRICAL INPUT 2 15 BRUSH MOTOR 5 25 eisso 16 DRIVING BELT 5 17 18 RECOVERY WATER SYSTEM 19 RECOVERY SYSTEM 19 VACUUM SYSTEM MOTOR ELECTRICAL INPUT 2 20 VACUUM SYSTEM MOTOR CARBON BRUSH CHECK AND 21 VACUUM SYSTEM MOTOR DISASSEMBLY ASSEMBLY 22 BRUSH PAD HOLDER DECK AND SQUEEGEE CLEANING CHECK SQUEEGEE 15 55 5 23 BRUSH PAD HOLDER DECK AND SQUEEGEE DISASSEMBLY ASSEMBLY 24 ivanell acinar reed Sateen aii 25 OTHER SYSTEMS 4 2 27 UPPER FRAME 27 SCREW AND NUT TIGHTENING EEEE Sn EEAS 28 ELECTRICAL SYSTEM wcceccccscecccccassccccecctsccctesscatcecees tastaceesccsdeceeeesesdeeeseceacageidecvsagnesieasadenedsiusgdgeassusadgucedessageeeestesdqeest eased 29 COMPONENT LAY OUT 29 WIRING DIAGRAM sist 6
5. 1000 mm 39 4 ZT 421 5 mm 16 6 in O 551 mm 21 7 in 380 mm 15 in 655 mm 25 8 in 2 A 0 715 1120 mm 28 1 44 1 100183 6 9097511000 1 2008 04 Micromatic 13E SERVICE MANUAL ENGLISH GENERAL INFORMATION SCHEDULED MAINTENANCE The lifespan of the machine and its maximum operating safety are ensured by correct and regular maintenance CAUTION Read carefully the instructions in the Safety chapter before performing any maintenance procedure The following table provides the scheduled maintenance The intervals shown may vary according to particular working conditions which are to be defined by the person in charge of the maintenance For instructions on scheduled and unscheduled maintenance procedures see the following paragraphs SCHEDULED MAINTENANCE TABLE Daily after using the ma chine Procedure Weekly Yearly Brush cleani
6. if necessary drain the hoses too 2 Drive the machine on a level floor 3 Remove the control panel 4 WARNING Do not touch uncovered electrical components while performing the following steps Connect the power supply cable 10 to the electrical mains Turn the program selection knob 5 to brushes solution flow activation 5b Disconnect cable no 4 A Apply an ammeter B on power supply cable no 1 C of the program selection knob D Turn on the machine with the main switch 6 and check that the brush motor electrical input is as follows e For Micromatic 13E 230 Volts 50 60 Hz with the brush on floor tiles 0 5 to 0 6 A with lifted brush 0 4 to 0 5 A For Micromatic 13E 115 Volts 60 Hz with the brush on floor tiles 1 5 to 1 8A with lifted brush 1 1 to 1 3 A Turn off the machine by pressing the switch 6 If the electrical input is higher perform the following procedures to detect and correct the abnormal input Remove from the brush rotation shafts flanges all the possible amounts of dirt or wrapped round materials ropes clothes etc which prevent or slow down its rotation If necessary remove and carefully clean the brush motor then check the moving part pulleys driving belt etc If the above mentioned procedures do not lead to a correct electrical input it is necessary to replace the motor 9 Perform steps 3 to 6 in the reverse order
7. 9097511000 1 2008 04 21 ENGLISH SERVICE MANUAL RECOVERY WATER SYSTEM VACUUM SYSTEM MOTOR DISASSEMBLY ASSEMBLY Disassemble the upper frame as shown in Other Systems chapter Disconnect the 2 terminals A Disconnect the vacuum hose B Remove the vacuum system motor If necessary replace the gasket D 5 CAUTION The gasket D prevents water from entering the vacuum system motor Check the gasket condition and replace it if it is cut torn or cracked 6 Assemble in the reverse order of disassembly NS 100192 22 9097511000 1 2008 04 Micromatic 13E SERVICE MANUAL ENGLISH RECOVERY WATER SYSTEM BRUSH PAD HOLDER DECK AND SQUEEGEE CLEANING CHECK SQUEEGEE DISASSEMBLY ASSEMBLY CAUTION It is advisable to wear protective gloves when cleaning the brush pad holder deck and the squeegees because there may be sharp debris Drive the machine on a level floor Make sure that the power supply cable 10 is disconnected from the electrical mains To reach for the brush squeegee holder deck lift the machine by using the handlebar 2 Remove the squeegees from the deck by pressing the mounting springs 27 Check the brush squeegee holder deck 9 and clean it In particular clean the compartment A and the vacuum hole B from dirt and debris Wash and clean the squeegee In particular clean the compartment C and t
8. It is advisable to use a precision ammeter or a digital multimeter with ammeter function lt 100187 Micromatic 13E 9097511000 1 2008 04 15 ENGLISH SERVICE MANUAL BRUSH DECK SYSTEM BRUSH MOTOR DISASSEMBLY ASSEMBLY 1 Disassemble the upper frame as shown in Other Systems chapter Disassembly 2 Disconnect the 2 connectors A of the condenser B 3 Disconnect the ground connector 4 Remove the 2 wires D from the terminal board E 5 Lift the frame and remove the brush deck as shown in the relevant paragraph 6 Remove the 3 mounting screws F and recover the washers under the frame 7 8 Remove the motor with great care ssembly Assemble the components in the reverse order of disassembly and note the following e Before installing a new motor loosen the driving belt as shown the relevant paragraph Place the driving belt around the motor pinion e After installing the motor adjust the driving belt tension as shown in the relevant paragraph P100188 16 9097511000 1 2008 04 Micromatic 13E SERVICE MANUAL ENGLISH BRUSH DECK SYSTEM DRIVING BELT CHECK REPLACEMENT ADJUSTMENT 1 Disassemble the upper frame as shown in Other Systems chapter Check 2 Visually inspect the driving belt A for integrity cuts tears or cracks and if necessary replace it according to the following
9. for integrity NOTE gasket creates vacuum in the tank that is necessary vacuuming the recovery water If necessary replace the gasket C by removing it from the transparent cover A 7 Check that the seating surface D of the gasket is integral and adequate for the gasket itself 8 Install the tanks and the transparent cover with vacuum grid P100190 Micromatic 13E 9097511000 1 2008 04 19 ENGLISH SERVICE MANUAL RECOVERY WATER SYSTEM VACUUM SYSTEM MOTOR ELECTRICAL INPUT CHECK WARNING This procedure must be performed by qualified personnel only 1 2 Drive the machine on a level floor Remove the control panel 4 WARNING Do not touch uncovered electrical components while performing the following steps Connect the power supply cable 10 to the electrical mains Turn the program selection knob 5 to vacuum system activation 5c Apply an ammeter A on the blue power supply cable B of the main switch D Turn on the machine with the main switch 6 and check that the vacuum system motor electrical input is as follows For Micromatic 13E 230 Volts 50 60 Hz e 2to2 3A For Micromatic 13E 115 Volts 60 Hz 4to4 5A Turn off the machine by pressing the switch 6 If the electrical input is higher perform the following procedures to detect and correct the abnormal input e Check the motor carbon
10. Make sure that the power supply cable 10 is disconnected from the electrical mains and place it around its holder 7 Remove the solution hose 17 from the quick coupling 11 Disconnect the solution hose from the quick coupling 23 Remove the solution tank 14 from the 2 mounting pins 26 Disconnect the vacuum system hose 20 and the squeegee vacuum hose 21 then remove the transparent cover with vacuum grid 15 and the recovery tank 16 Remove the covers A snap rings B washers C and wheels D Remove the 8 mounting screws E of the frames Disengage and carefully lift the upper frame F from the lower frame G and lay it as shown in the figure Pay attention to water hoses vacuum hoses and wiring harness H Assembly 10 Assemble in the reverse order of disassembly and pay attention to water hoses vacuum hoses and wiring harness H P100195 Micromatic 13E 9097511000 1 2008 04 27 ENGLISH SERVICE MANUAL OTHER SYSTEMS SCREW AND NUT TIGHTENING CHECK 1 the machine to the appointed disposal area then empty the recovery tank 16 2 Place the machine on a hoisting system if available Otherwise drive the machine on a level floor 3 Disconnect the power supply cable 10 from the electrical mains 4 Check e Tightening of mounting screws and nuts e Correct position of fasteners e Visible faults in the components Leaks of fluids 5 If necessary disa
11. brushes If necessary remove and carefully clean the brush motor then check the moving part pulleys driving belt etc If the above mentioned procedures do not lead to a correct electrical input it is necessary to replace the motor Perform steps 2 to 5 in the reverse order NOTE It is advisable to use precision ammeter or a digital multimeter with ammeter function P100191 20 9097511000 1 2008 04 Micromatic 13E SERVICE MANUAL ENGLISH RECOVERY WATER SYSTEM VACUUM SYSTEM MOTOR CARBON BRUSH CHECK AND REPLACEMENT 5 Disassemble the upper frame as shown in Other Systems chapter Remove the suction hose and the 2 terminals from the vacuum system motor Remove the vacuum system motor see the procedure in the relevant paragraph At the workbench remove the cover A press fitted from the vacuum system motor B Remove the screws C Disconnect the electrical connections D Remove the carbon brushes E Check the carbon brushes for wear Replace the carbon brushes when the contact with the motor armature is insufficient the carbon brushes are worn the carbon brush contact surface is not integral the thrust spring is broken etc If necessary replace the carbon brushes Replace the carbon brushes as an assembly Assemble in the reverse order of disassembly 5301555 Micromatic 13E
12. procedure 3 Check the driving belt tension A according to the following procedure Replacement 4 replace the driving belt A loosen the bolt of the pulley and the nut D 5 To loosen the driving belt turn the screw counter clockwise 6 Remove the brush motor F 7 Remove the driving belt A and replace it with a new one 8 During driving belt installation e Insert the new driving belt in the slots G e Install the driving belt with the marked side toward the outside of the right pulley 9 Stretch the driving belt according to the following procedure Belt tensioning 10 Check the driving belt tension A The tension is correct e When pressing the driving belt in its centre with a force of 22 Ib 10 kg I the driving belt bends for 0 40 in 10 mm If necessary stretch the driving belt according to the following procedure 11 Loosen the bolt C and the nut D 12 To stretch the driving belt adjust the position of the pulley C with the screw E 13 When tensioning procedure has been performed tighten the nut D and the bolt Reset 13 Perform steps 1 in the reverse order
13. the power supply cable plug cannot be connected to the outlet have new grounded outlet installed by a qualified technician according to the law in force Before connecting the power supply cable to the electrical mains check that frequency and voltage shown on the machine serial number plate 1 match the electrical mains voltage Do not unplug the machine by pulling the supply cable To unplug grasp the plug not the cable Do not handle the plug or the machine with wet hands Turn off all controls before unplugging Regularly check the power supply cable for damages cracks cuts etc If the power supply cable is damaged replace it immediately To avoid any risk if the power supply cable is damaged contact the Nilfisk Service Center or a qualified technician Do not pull or carry the machine by the power supply cable and never use the power supply cable as handle Do not close a door on the power supply cable or pull the power supply cable around sharp edges or corners Do not run the machine on the power supply cable The brushes must not come into contact with the power supply cable Keep the power supply cable away from heated surfaces reduce the risk of fire electric shock or injury do not leave the machine unattended when it is plugged in Disconnect the machine from the electrical mains when not in use and before performing maintenance procedures Always protect the machine against t
14. ATION In case of fire use a powder fire extinguisher not a water one WARNING Do tamper with the machine safety guards and follow the ordinary maintenance instructions scrupulously Do not allow any object to enter into the openings Do not use the machine if the openings are clogged Always keep the openings free from dust hairs and any other foreign material which could reduce the air flow Do not remove or modify the plates affixed to the machine This machine cannot be used on roads or public streets Pay attention during machine transportation when temperature is below freezing point The water in the recovery tank or in the hoses could freeze and seriously damage the machine Use brushes and pads supplied with the machine and those specified in the User Manual Using other brushes or pads could reduce safety In case of machine malfunctions ensure that these are not caused by a lack of maintenance Otherwise request assistance from the authorised personnel or from an authorised Service Center If the machine does not work properly is damaged has water or foam leaks has been left outdoors exposed to bad weather conditions is wet or has been dropped into water turn it off immediately and contact the Nilfisk Service Center or a qualified technician If parts must be replaced require ORIGINAL spare parts from an Authorised Dealer or Retailer To ensure machine proper and safe operation the scheduled maintenance sho
15. Micromatic 13E SERVICE MANUAL Advance model 9087230020 Advance by Nilfisk Advance 9097511000 1 2008 04 SERVICE MANUAL ENGLISH TABLE OF CONTENTS 2 2 MACHINE LIF TING 2 MACHINE 2 OTHER REFERENCE MANYAL 2 2 GENERAL SAFETY PRECAUTIONS 3 TECHNICAL 5 DIMENSIONS dh casa began 6 SCHEDULED sates Hah 7 7 7 MACHINE NOMENCLATURE 8 SOLUTION 557 1 SOLUTION TANK 25 EEL EEK OR Hearne 11 SOLUTION FILTER 5 11 SOLUTION PUMP DISASSEMBLY ASSEMBLY 12 TROUBLESHOOTING
16. he sun rain and bad weather both under operation and inactivity condition Store the machine indoors a dry place Do not allow to be used as a toy Close attention is necessary when used near children Use only as shown in this Manual Use only Nilfisk s recommended accessories all necessary precautions to prevent hair jewelry and loose clothes from being caught by the machine moving parts Do leave the machine unattended without being sure that it cannot move independently Donotuse the machine on slopes with a gradient exceeding the specifications Do not use the machine in particularly dusty areas While using this machine take care not to cause damage to people or objects Do not bump into furniture shelves or scaffoldings especially where there is a risk of falling objects Do not put can containing fluids on the machine The machine operating temperature must be between 32 F and 104 F 0 C and 40 C The machine storage temperature must be between 32 F 104 F 0 C and 40 C The humidity must be between 30 and 95 Donotuse the machine as a means of transport Donotuse the machine on slopes with a gradient exceeding the specifications Do not allow the brush pad to operate while the machine is stationary to avoid damaging the floor Micromatic 13E 9097511000 1 2008 04 3 ENGLISH SERVICE MANUAL GENERAL INFORM
17. he vacuum hole D Check that the blade E and the blade F are integral and free from cuts and lacerations if necessary replace them Install the squeegees Check the wheels G and if necessary clean them If the wheels are too worn replace them Check the suction hose H for integrity and check that it is properly connected to the deck hose 2 100193 Micromatic 13E 9097511000 1 2008 04 23 ENGLISH SERVICE MANUAL RECOVERY WATER SYSTEM BRUSH PAD HOLDER DECK AND SQUEEGEE DISASSEMBLY ASSEMBLY CAUTION It is advisable to wear protective gloves when removing the brush pad holder deck and the squeegees because there may be sharp debris Drive the machine on a level floor Make sure that the power supply cable 10 is disconnected from the electrical mains To reach for the brush squeegee holder deck lift the machine by using the handlebar 2 Remove the screws A and recover the washers B Carefully remove the brush squeegee holder deck C then recover the pins D and the springs E Check the cover F for integrity if it is cracked or broken replace it Assemble in the reverse order of disassembly 5 4 24 9097511000 1 2008 04 Micromatic 13E SERVICE MANUAL ENGLISH RECOVERY WATER SYSTEM TROUBLESHOOTING Dirty water vacuumi
18. isposal area Lift the brush squeegee holder deck and turn the parking lever to position 24b Remove the solution hose 17 from the quick coupling 11 Remove the solution tank 14 from the 2 mounting pins 26 Empty the solution tank 14 through the plug 18 or the hole of the solution hose 17 Rinse the tank with clean water Install the tank and the solution hose SOLUTION FILTER CLEANING Perform steps 1 to 4 shown in the previous paragraph 1 Disengage the solution hose plug 17 and remove it from the solution tank 2 Remove the quick coupling 11 and the solution hose 17 3 Rinse the filter 25 with clean water 4 Install the supply hose 35 Micromatic 13E 4 1 ENGLISH SERVICE MANUAL SOLUTION SYSTEM SOLUTION PUMP DISASSEMBLY ASSEMBLY 1 Disassemble the upper frame as shown in Other Systems chapter Disassembly WARNINGI Install the solution pump in the direction shown the arrow Remove the grommet A Remove the screw B Disengage the hose clips C Remove the solution pump D Assemble in the reverse order of disassembly
19. ng Squeegee cleaning Tank and vacuum grid cleaning Squeegee blade check and replacement Solution hose filter cleaning Screw and nut tightening check Vacuum system motor carbon brush check and replacement 1 And after the first 8 working hours Micromatic 13E 9097511000 1 2008 04 7 ENGLISH SERVICE MANUAL GENERAL INFORMATION MACHINE NOMENCLATURE Throughout this Manual you will find numbers in brackets for example 2 These numbers refer to the components indicated in these two nomenclature pages Refer to these pages whenever you need to identify a component mentioned in the text Serial number plate technical data conformity certification Handlebar Handlebar tilting adjustment lock unlock lever Control panel Program selection knob Program brushes vacuum system solution flow activation Program brushes solution flow activation Program vacuum system activation Program fitted carpet cleaning and floor wiping optional Main switch Power supply cable holder Wheels on fixed axle Brush squeegee holder deck Power supply cable Solution hose quick coupling to the pump Front squeegee Rear squeegee Solution tank Solution tank opened Transparent cover with vacuum grid Recovery tank Solution hose Solution tank filler plug Recovery tank drain plug Vacuum system motor suction hose Squeegee vacuum hose One wa
20. ng is insufficient or there is no vacuuming Possible causes 10 11 The vacuum grid 15 is dirty clean The transparent cover with vacuum grid 15 of the recovery tank 16 is not properly positioned place it properly The drain plug 19 of the recovery tank is not properly positioned place it properly The transparent cover gasket is not efficient replace The squeegees 12 13 or the vacuum hoses 20 21 are clogged or damaged clean or repair replace The brush squeegee holder deck cover 9 is damaged replace The vacuum system motor carbon brushes 29 are worn replace The vacuum system motor 29 is faulty repair or replace The main switch 6 is broken replace The machine wiring harness is damaged repair The program selection knob 5 is broken replace The squeegees are streacking or do not collect water Possible causes 1 2 3 There is debris under the squeegee blades remove The front and or rear blades are worn replace There is dirt or debris on the brush squeegee holder deck wheel pins clean Micromatic 13E 9097511000 1 2008 04 25 ENGLISH SERVICE MANUAL RECOVERY WATER SYSTEM 26 9097511000 1 2008 04 Micromatic 13E SERVICE MANUAL ENGLISH OTHER SYSTEMS UPPER FRAME DISASSEMBLY ASSEMBLY Disassembly 1 ON Drive the machine a level floor
21. nt or useful functions CONSULTATION It indicates the necessity to refer to the User Manual before performing any procedure 2 9097511000 1 2008 04 Micromatic 13E SERVICE MANUAL ENGLISH GENERAL INFORMATION GENERAL SAFETY PRECAUTIONS Specific warnings cautions to inform about potential damages to people and machine shown below DANGER Always disconnect the power supply cable when the machine is not in use before performing maintenance procedures before replacing the brush pad holder and before opening any access panel This machine must be used by properly trained and authorized personnel only Children or disabled people cannot use this machine Do not wear jewelry when working near electrical components Do not work under the lifted machine without supporting it with safety stands Donot operate the machine near toxic dangerous flammable and or explosive powders liquids or vapours WARNING The machine power supply cable is grounded and the relevant plug is grounded too In case of machine malfunction or breakdown grounding connection reduces the risk of electric shock power supply cable plug must be connected to an appropriate outlet which is grounded according to law in force Improper connection can cause electric shock Consult a qualified technician to make sure that the outlet is properly grounded Donot tamper with the power supply cable plug If
22. olution tank Machines have been tested under the following conditions e Maximum brush and squeegee size Full clean water tank e Optional components installed e Weight on wheels checked e Print on the floor checked on cement for each single wheel e Result expressed as maximum value for front and rear wheels 19 8 33 0 Ib 9 15 kg Performance MICROMATIC 13E 115 Volt Vacuuming 0 01 MPa 0 10 Bar Solution flow 0 13 gal min 0 4 L min Theoretic real productivity 14 208 ft h 7 104 2 1 320 m h 660 m h Solution autonomy 18 min Brush pad speed 200 rpm Sound pressure level at workstation ISO 11201 ISO 4871 LpA 72 5 dB A 3 dB A Machine sound pressure level ISO 3744 ISO 4871 LWA 86 dB A Vacuum system motor power 450 W 0 60 HP Brush pad motor power 100 W 0 13 HP Gradeability 2 1 Solution tank capacity 1 8 gal 7 0 L Recovery tank capacity 2 1 gal 8 0 L Vibration level at the operator s arms ISO 5349 1 gt 98 42 in s lt 2 5 m s Power supply cable length 590 in 15 m Total electrical input 5 2A Minimum turning radius 45 3 in 1 150 mm Micromatic 13E 9097511000 1 2008 04 5 ENGLISH SERVICE MANUAL GENERAL INFORMATION DIMENSIONS A MA MA rN
23. ssemble the upper frame as shown in the previous paragraph and check tightening of screws and nuts as shown in step 4 6 Assemble in the reverse order of removal 28 9097511000 1 2008 04 Micromatic 13E SERVICE MANUAL ENGLISH ELECTRICAL SYSTEM COMPONENT LAYOUT 1 Brush motor condenser C2 Filtering condenser D1 Pump diode ES1 Relay 115 V only M1 Brush pad holder motor M2 Vacuum system motor P Water pump PL Plug Swi Main switch SW2 Program selection knob 100196 Micromatic 13E 9097511000 1 2008 04 29 ENGLISH SERVICE MANUAL ELECTRICAL SYSTEM WIRING DIAGRAM Key Color codes 1 Brush motor condenser BK Black C2 Filtering condenser BU Blue D1 Pump diode BN Brown ES1 Relay 115 V only GN Green M1 Brush pad holder motor GY Grey M2 Vacuum system motor OG Orange P Water pump PK Pink PL Plug RD Red Swi Main switch VT Violet SW2 Program selection knob WH White YE Yellow P100167 30 9097511000 1 2008 04 Micromatic 13E
24. wn in the relevant chapter of this Manual must be performed by the authorised personnel or by an authorised Service Center Carefully read all the instructions before performing maintenance repair procedure Do not wash the machine with direct or pressurised water jets or with corrosive substances The machine must be disposed of properly because of the presence of toxic harmful materials electronic components etc which are subject to standards that require disposal in special centres see the Scrapping chapter 4 9097511000 1 2008 04 Micromatic 13E SERVICE MANUAL ENGLISH TECHNICAL DATA GENERAL INFORMATION General MICROMATIC 13E 115 Volt Min max machine length at the handlebar 28 1 44 1 in 715 1 120 Machine width with squeegee 15 1 385 Machine brush deck width 15 1 in 385 mm Maximum machine height with adjustable handlebar 39 4 in 1 000 mm Turning radius 45 3 in 1 150 mm Total machine weight 48 510 22 kg Cleaning width 12 9 in 330 mm Central wheel diameter 7 0 in 180 mm Brush diameter 6 5 in 165 mm Brush number No 2 brushes pads Squeegee system Fixed on deck Straight squeegee width 15 0 in 385 mm Squeegee blades type Wheel pressure on the floor Front Rear PU 65 SH 101 psi 0 7 N mm Brush pad pressure on the floor with empty full s
25. y valve Solution hose quick coupling to the brushes 24 24 24 25 26 27 28 29 30 Parking Disengaged parking lever Engaged parking lever Solution filter Solution tank mounting pins Squeegee mounting springs Solution hose right quick coupling from the tank to the pump Vacuum system motor Driving belt idler roller 31 Solution hose 32 Right pulley 33 Driving belt 34 Driving belt tension adjustment roller 35 Left pulley 36 Brush motor pickup condenser 37 Brush motor 38 Solution pump 39 Solution hose left quick coupling from the pump to the brushes 14 25 18 17 22 100184 9097511000 1 2008 04 Micromatic 13E SERVICE MANUAL ENGLISH GENERAL INFORMATION SS MACHINE NOMENCLATURE Continues P100185 Micromatic 13E 9097511000 1 2008 04 9 ENGLISH SERVICE MANUAL GENERAL INFORMATION 10 9097511000 1 2008 04 Micromatic 13E SERVICE MANUAL ENGLISH SOLUTION SYSTEM SOLUTION TANK CLEANING Turn off the machine by pressing the switch 6 Disconnect the power supply cable 10 from the electrical mains and place it on the holder 7 Drive the machine to the appointed d
Download Pdf Manuals
Related Search