View the Installation Instructions
Contents
1. HONDA Accessory Application Publications No INSTALLATION 17 ALUMINUM WHEEL All 43550 INSTRUCTIONS P N 08W17 SZT 100 aN One Issue Date AUG 2010 PARTS LIST Parts for TPMS sensor assembly Aluminum wheel Tire pressure sensor assembly The illustration may differ from the actual wheel J Washer Wheel center cap Valve nut Tire and loading information label O L TOOLS AND SUPPLIES REQUIRED Ratchet 11 mm Socket TPMS Information T h Give this to your customer orque wrenc Isopropyl alcohol Shop towel HDS Universal TPMS sensor reader AEQVT55 Available through the Honda Tool and Equipment Supplemental information program On the iN click on Service Service Bay Tool and Equipment Program then enter the number under Search Or call 888 424 6857 SPECIFICATIONS Rim size 17 x 6 1 2 J inset 45 Tire size 205 45R17 88Y Bolt hole PCD 114 3 5 holes Front 230kPa 2 3 kgf cm 33 psi Tire pressure 230kPa Rear 2 3 kgt om 33 psi 2010 American Honda Motor Co Inc All Rights Reserved All 43550 1008 08W17 SZT 1000 91 1 of 5 INSTALLATION Customer Information The information in this installation instruction is intended for use only by skilled technicians who have the proper tools equipment and training to correctly and safely add equipment to your vehicle These procedures should not be attempted by do2. it yourselfers NOTE equipped with TPMS Tire Pressure Monitoring System and TPMS sensor installation procedure e Install the correct size tire aluminum wheel Do not damage the wheel center cap when installing the emblem e The wheel nut torque is 108 N m 80 Ibf ft 2of5 All 43550 1008 This aluminum wheel is designed for use on a vehicle This aluminum wheel is equipped with a TPMS sensor See the service manual for tire replacement procedure Use a tire changer to install and remove the tire Do not use a tire lever as it may cause damage to the tire and 1 Before installing the tire pressure sensor clean the mating surface on the sensor and the aluminum wheel WASHER GROMMET SENSOR HOUSING SURFACE gt OUTSIDE TIRE PRESSURE SENSOR ASSEMBLY WHEEL CENTER VALVE NUT Torque to 4 N m ALUMINUM AMIN WASHER 3 0 Ibf ft SENSOR HOUSING SURFACE TIRE PRESSURE SENSOR ASSEMBLY WHEEL PROTRUSION VIEW FROM THE INSIDE OF THE ALUMINUM WHEEL Remove the valve cap Install the tire pressure sensor and the washer to the wheel and finger tighten the valve nut Make sure the pressure sensor is resting on the wheel NOTE Make sure the sensor housing surface does not protrude into the bead area of the wheel This prevents the sensor housing from being caught on the bead of the tire when installing the tire Torque the valve nut to 4 N
3. page included in this kit and attach it to the vehicle s service history booklet e Be sure to explain the contents of the Supplemental Information to your customer before delivering the vehicle e Be sure to give the wheel cleaning information and TPMS information to your customer 10 DIGIT NUMBER TIRE AND DATA LINK LOADING CONNECTOR INFORMATION LABEL 4of5 All 43550 1008 2010 American Honda Motor Co Inc All Rights Reserved REINSTALLING STANDARD WHEELS If the original equipment standard wheels are reinstalled on the vehicle the low tire pressure warning threshold must be restored to the factory setting follow the procedure below NOTE Have the standard tire pressure label on hand TPMS UNIT REPLACEMENT If the TPMS unit is replaced redo the Inch up Tire Pressure Programming and Tire Pressure ID Memorization STANDARD TIRE PRESSURE PROGRAMMING To return the TPMS programming from the inch up tire to the standard tire change the programming 1 Connect the HDS to the vehicle make sure the correct VIN is populated and enter the mileage 2 At the System Selection Menu click TPMS 3 At the Mode Menu click on DTCs and clear any stored codes 4 Go back to the Mode Menu and click on Threshold Rewriting 5 Click on Reprogramming for standard tires and follow the screen prompts 6 After programming write the standard tire pressur
4. e in the Supplemental Information page then click the check button 7 Attach the standard tire pressure information label over the old label in the driver s doorjamb 8 Sign the Service History Page for Honda Accessory Wheels Write the tire size tire pressure HDS version dealer name technician s signature and date in the Service History Page for Honda Accessory Wheels 2010 American Honda Motor Co Inc All Rights Reserved THRESHOLD DATA CHECK If you are unsure where the low tire pressure warning threshold is set do the following 1 All 43550 1008 Connect the HDS to the vehicle and make sure the correct VIN is populated and enter the mileage At the System Selection Menu click TPMS Click on Threshold Rewriting Click on Threshold Data Check DATA LINK CONNECTOR 5 of 5
5. m 3 0 Ibf ft while holding the tire pressure sensor against the wheel Reinstall the valve cap NOTE e Do not reuse torqued grommets otherwise the valve system may leak e Do not use pneumatic or electric tools on the valve nut e Tightening the nut above the specified torque can damage the grommet Install the tires according to the instructions in the service manual Install the wheels on the vehicle and torque the wheel nuts to 108 N m 80 Ibf ft 2010 American Honda Motor Co Inc All Rights Reserved 6 Open the driver s door Using isopropyl alcohol on a shop towel thoroughly clean the door jamb where the tire and loading information label will attach DRIVER S DOOR OPENING O fi TIRE AND LOADING INFORMATION LABEL DOOR JAMB Clean with isopropyl alcohol VEHICLE TIRE INFORMATION LABEL 7 Remove the adhesive backing from the tire and loading information label and attach it over the vehicle tire information label 8 Insert the Supplemental Information page into the owner s manual 2010 American Honda Motor Co Inc All Rights Reserved MEMORIZING THE TIRE PRESSURE SENSOR ID 9 Using the HDS and the universal TPMS sensor reader AEQVT55 memorize each tire pressure sensor ID according to the instructions in the service manual Memorizing the Tire Pressure Sensor ID DATA LINK CONNECTOR HDS UNIVERSAL 10 Perform the Inch up Tire Pressure pr
6. ogramming procedure as follows All 43550 1008 3 of 5 INCH UP TIRE PRESSURE PROGRAMMING LOW AIR PRESSURE WARNING THRESHOLD REPROGRAMMING 1 After the sensor ID learning using the HDS back up to the TPMS Mode Menu and click on Threshold Rewriting 2 Select Reprogramming for accessory tires 3 When the HDS says Do you want to rewrite the threshold data click YES 4 Check that Please enter the tire information code of new tires is shown and click the Keyboard icon 5 Enter the 10 digit tire information code printed on the new tire and loading information label then click the check icon 6 Check that the tire pressure shown on HDS and the new tire pressure on the tire and loading information label are the same then click the YES button 7 Check that the current air pressure setting shown on HDS is correct and Reprogramming the threshold data for non standard tires has completed successfully is shown 8 After programming write the tire pressure indicated on the HDS in the Service History Page for Honda Accessory Wheels then click the check icon 9 After programming complete the Service History Page for Honda Accessory Wheels according to the procedure on page 5 NOTE e After finishing the work write the tire size tire pressure HDS version dealer name technician s signature and date in Service History Page for Honda Accessory Alloy Wheels
Download Pdf Manuals
Related Search