VIBCO`s TP-10 Plate Compactor Service Manual
Contents
1. 18x2HHG5 2 26 Hand Reciever Weld 10TP018 1 27 Inner Belt Guard Weld 10TP013 1 28 Flat Head Socket Screw M8 1 25x16FHS 4 29 Hex Head Screw 3 8 16x1 3 4HH 1 30 Grade 8 Flat Washer 3 8FWG8 2 31 Heavy Lockwasher 3 8LW 1 32 Nylon Lock Nut 3 8 16LN 1 33 Handle Isolator 10TP015 1 34 Powertwist Belt A AL 1 35 Clutch 5 8 Bore 16GR53 1 36 Fender Washer 1 4X1FNDRW 1 37 Lockwasher 1 4LW 1 38 Grade 8 Hex Head Screw 1 4 28x3 4HHG8 1 39 Hex Head Bolt M8 1 25x16HH 5 40 Heavy Lockwasher 5 16LW 9 41 7 8ID Grip 18VR053 2 42 Handle Weld 10TP021 1 43 Solid Pipe Plug 1 8NPT 2 44 Clutch Key 3 16 X 1 1 2 12. X v En LR Vibrators Vibco Com Vibco Inc reserves the right to change and improve any parts or speeticutions without notice and without incurring any obligation relating to such change Ol dL IOW Jon 212M sn JoyeIq yu 008 7002 lVl33S NI93g8 ONI ODAIA C 00 9 008 C6 C 6 S 10r Suoud 86820 IN GUILIOAM 8 xoq Od a gt gt o cn e ie NO a Qo GLOS 8Z8 S06 XY4 0 S9r 009 L61 878 S06 LXL 181 1UO OOnoDSSISSIW SAU UIMUNG GIZZ Dppupo ul Model TP 10 Item Part Number Number Description Part Number Required 1 Element Assembly 10TP008 1 2 Retaining Ring 201022 2 3 O Ring 122026 2 4 Closed Bearing Housing 122021 1 5 Spherical Bearing 201023 2 6 Element Housing 122024 1 1 7 Eccentric Shaft 122019 4 1 8 Set Screw 1 4 20X1 2SS 2 9 Sheave Key 201017 1 10 Open Bearing Housing 122020 1 11 Oil Shield 201143 1 12 Oil Seal 201025 1 13 Sheave Bushing 201016 1 14 Sheave 201015 2 1 15 Baseplate Weld 10TP002 1 16 Engine Plate 10TP009 1 17 Shock Absorber 201028 4 18 1 2 13 Grade 5 Hex Heads 1 2 20x3 AHH 2 19 Lockwasher 1 2LW 10 20 Screw Hex Head 1 2 13x3 4HH 8 21 Outer Belt Guard 10TP014 1 22 Honda Engine GX 100 1 23 Flat Washer SAE 5 16FW 9 24 Hex Nut 5 16 18HN 4 25 Hex Head Cap Screw 5 16
3. e operating manual CAREFULLY Remember to check the engine oil Make sure the belt guard is securely bolted in place The vibratory element is filled with 2 fluid ounces of SAE 90 EP gear lubricant and is sealed at the factory Note Do not overfill the element if servicing this can damage the unit extensively and may void the warranty Unlock the handle by removing the pin and lowering the handle into position Start the machine After warm up move the control lever to full throttle position The motor should run at 3250 RPM maximum The clutch will automatically engage at approximately 1850 RPM and vibration will begin The unit will now begin to pull itself forward Let compactor move on its own power and guide it by the handle Uneven or sloping terrain may cause the machine to slide sideways The operator must then steer toward the rise thus causing the compactor to travel at an angle Do not add fuel while the engine is running Stop the engine and if possible allow a cooling period to prevent spilled fuel from igniting on contact with hot engine parts Before making any adjustments disconnect the spark plug cable to prevent unintentional starting Make sure that the belt guard is securely bolted in place REMEMBER a careful operator is always the best insurance against accidents If you have any questions or comments feel free to call technical support at 1 800 633 0032 Or e mail us at I
4. ndle and a water tank on asphalt models The vibrational force and forward motion of these machines is induced by rotation of an eccentrically weighted shaft The water tank on asphalt models wets the plate and pavement surfaces appropriately to avoid the adhesion which can occur with the asphalt surface Serial Number Location Engine When ordering replacement parts from the engine distributor state the model specification and serial number Model and spec numbers for both engines are located on the flywheel cover Honda serial numbers are found on the front of the crankcase housing and the Robin serial numbers are located on the base of the engine Compactor The Vibco model and serial numbers are mounted on the front of the engine plate Furnish both numbers when corresponding with your authorized dealer Maintenance Keep your machine clean Every 10 hours or daily 1 Periodically check bolts and nuts for tightness especially in the period following initial operation 2 Check engine oil daily 3 Clear air filter periodically 4 Check and tighten element clamp screws with a torque wrench for 38 40 ft lbs Every 50 hours or weekly Check belt tension Change engine oil Check and tighten all nuts and bolts If water flow through the sprinkler pipe on asphalt units fails clear pipe using carburetor cleaner Check vibrator element seal for leaks EON e Operating Notes Before starting the machine READ the engin
5. uen We re The Vibrator Guys z Head Office Vibco Inc 7 5 Stilson Road Canadian Branch Vibco Canada 2215 Dunwin Drive pt Wyomomg RI 02898 TEL 800 633 0032 FAX 401 539 2584 Mississauga Ontario L5L1X1 TEL 905 828 4191 FAX 905 828 5015 WWW VIBCO COM Operators Manual Model TP 10 High Compaction Dirt Plate Compactor Engine Specs Standard Honda GX 100 4 stroke overhead camshaft single cylinder Forced air cooled 3 0 Horsepower 2 2 Kilowatts 3500 RPM Rewind starter Low oil alert system Transistorized magneto ignition Specifications Metric 43 kg 6675 N English 95 Ibs 1500 Ibs Specification Weight Centrifugal Force Specific Centrifugal Force Vibration Frequency Contact Dimensions 10 psi 5400 VPM 12 x 13 5 30 5 cm x 34 cm Introduction Vibco Inc reserves the right to change and improve any parts or specifications without notice and without incurring any obligation relating to such change Vibco plate type compactors are used for compacting loose layers of soil or asphalt into load bearing surfaces The vibration aligns the particles in the material being compacted in order to achieve maximum density thus eliminating hollow spaces or cavities They are successfully used for sandy granular and partially cohesive materials as well as for asphalt finishing The main Components of the compactors are the base plate vibratory element engine plate steering ha
Download Pdf Manuals
Related Search