SEAT BELTS - MyZRoadster
Contents
1. Anchor bolt 6 Shoulder anchor cover Spacer 8 Retaining washer 9 Spacer 10 Outer anchor cover CAUTION Before servicing SRS turn the ignition switch OFF disconnect both battery cables and wait at least 3 minutes REMOVAL OF SEAT BELT RETRACTOR 1 ARON Remove the shoulder anchor cover on the seat belt anchor Remove the anchor bolt Slide up outer anchor cover and remove the anchor bolt Remove the rear side finisher Refer to El 37 Removal and Installation for Roadster Models Remove the center console Refer to IP 10 Component Parts Drawing Remove the luggage floor finisher lower Refer to E1 41 Removal and Installation for Roadster Models Remove the woofer and woofer amp BOSE system bracket mounting bolts Refer to AV 47 Removal and Installation of Woofer and Woofer Amp BOSE System Remove the rear floor box Refer to El 41 Removal and Installation for Roadster Models Revision 2005 August SB 6 2006 350Z SEAT BELTS 9 Disconnect the seat belt pre tensioner connector CAUTION e For installing removing pre tensioner seat belt connec tor insert screwdriver wrapped in tape into notch lift lock and remove connector e Install connector with lock raised and push lock into connector Screwdriver Unlock t PHIA0341E 10 Remove the seat belt pre tensioner retractor fixing screw and anchor bolt and then remove the seat belt retractor 11 Remove the s2. the seat belt pre tensioner assembly turn the ignition switch off disconnect the both battery cables and wait at least 3 minutes e Donotuse electrical test equipment for seat belt pre tensioner connector After replacing or reinstalling seat belt pre tensioner assembly or reconnecting front seat belt pre tensioner connector check the system function Refer to SRS 21 SRS Operation Check Do not use disassemble buckle or seat belt assembly Replace anchor bolts if they are deformed or worn out Never oil tongue and buckle If any component of seat belt assembly is questionable do not repair Replace the whole seat belt assembly e If webbing is cut frayed or damaged replace seat belt assembly e When replacing seat belt assembly use a genuine NISSAN seat belt assembly AFTER A COLLISION WARNING Inspect all seat belt assemblies including retractors and attaching hardware after any collision NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the col lision was minor and the belts show no damage and continue to operate properly Failure to do so could result in serious personal injury in an accident Seat belt assemblies not in use during a colli sion should also be replaced if either damage or improper operation is noted Seat belt pre tensioner should be replaced even if the seat belts are not in use during a frontal collision in which the air bags are deployed Replace any seat bel
3. August SB 8 2006 350Z SEAT BELTS SEAT BELT RETRACTOR ON VEHICLE CHECK Emergency Locking Retractors ELR NOTE All seat belt retractors are of the Emergency Locking Retractors ELR type In an emergency sudden stop the retractor will lock and prevent the webbing from extending any further Check the seat belt retractors using the following test s to determine if a retractor assembly is operating prop erly ELR Function Stationary Check Grasp the shoulder webbing and pull forward quickly The retractor should lock and prevent the belt from extending further ELR Function Moving Check WARNING Perform the following test in a safe open area clear of other vehicles and obstructions for example a large empty parking lot Road surface must be paved and dry Do Not perform the following test on wet or gravel roads or on public streets and highways This could result in an accident and serious personal injury The driver and passenger must be prepared to brace themselves in the event the retractor does not lock 1 Fasten driver s seat belt Buckle a passenger into the seat for the belt that is to be tested 2 Proceed to the designated safe area 3 Drive the vehicle at approximately 16 km h 10 MPH Notify any passengers of a pending sudden stop The driver and passenger must be prepared to brace themselves in the event the retractor does not lock Apply brakes firmly and make a very hard stop While stopping seat belts sho
4. H RESTRAINTS SECTION S B SEAT BELTS CONTENTS PREGAUTIONS itta fetcentevecedectecesee aankan aeaaeai 2 REMOVAL OF SEAT BELT BUCKLE 5 Precautions for Supplemental Restraint System INSTALLATION OF SEAT BELT BUCKLE 5 SRS AIR BAG and SEAT BELT PRE TEN Removal and Installation of Seat Belt Roadster 6 SIONER eir thee madalal ae ay ies 2 REMOVAL OF SEAT BELT RETRACTOR 6 Precaution for Seat Belt Service 2 INSTALLATION OF SEAT BELT RETRACTOR 7 AFTER A COLLISION pei aii aeann iaaea 2 REMOVAL OF SEAT BELT BUCKLE Precautions for Battery Service 3 INSTALLATION OF SEAT BELT BUCKLE SEAT BEETS E Dt E E T 4 Seat Belt Inspection mrrmn System Description snrnmase 4 AFTER A COLLISION mimiinemenananaaaanna SEAT BELT WARNING CHIME 4 PRELIMINARY CHECKS nieee SEAT BELT WARNING LAMP neeese 4 SEAT BELT RETRACTOR ON VEHICLE Removal and Installation of Seat Belt Coupe 4 GHECKeasiios ciate dace ate aida ere 9 REMOVAL OF SEAT BELT RETRACTOR 4 SEAT BELT RETRACTOR OFF VEHICLE INSTALLATION OF SEAT BELT RETRACTOR 5 GHEEK E A ts eGo alaalia east et reeds 9 Revision 2005 August SB 1 2006 350Z PRECAUTIONS PRECAUTIONS PFP 00001 Precautions for Supplemental Restraint System SRS AIR BAG
5. and SEAT BELT PRE TENSIONER nHSo0001 The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE TENSIONER used along with a front seat belt helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision This system includes seat belt switch inputs and dual stage front air bag modules The SRS system uses the seat belt switches to determine the front air bag deployment and may only deploy one front air bag depending on the severity of a collision and whether the front occupants are belted or unbelted Information necessary to service the system safely is included in the SRS and SB section of this Service Man ual WARNING e To avoid rendering the SRS inoperative which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation all maintenance must be per formed by an authorized NISSAN INFINITI dealer e Improper maintenance including incorrect removal and installation of the SRS can lead to per sonal injury caused by unintentional activation of the system For removal of Spiral Cable and Air Bag Module see the SRS section e Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual SRS wiring harnesses can be identified by yellow and or orange harnesses or harness connectors Precaution for Seat Belt Service igen CAUTION e Before removing
6. ash guide and then remove the seat belt assembly INSTALLATION OF SEAT BELT RETRACTOR CAUTION Before servicing SRS turn the ignition switch OFF disconnect both battery cables and wait at least 3 minutes Install in the reverse order of removal REMOVAL OF SEAT BELT BUCKLE 1 Remove the seat Refer to SE 71 REMOVAL 2 Remove the screws and remove the seat cushion inner finisher 3 Remove the anchor bolt and remove the buckle INSTALLATION OF SEAT BELT BUCKLE Install in the reverse order of removal Revision 2005 August x Waving K staining washer son bolt TC 43 1 54 9 Nem Seat belt buckle 4 4 5 6 kg m 32 40 ft lb Ba 2006 350Z SEAT BELTS Seat Belt Inspection nvts00007 AFTER A COLLISION WARNING Inspect all seat belt assemblies including retractors and attached hardware after any collision NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the col lision was minor and the belts show no damage and continue to operate properly Failure to do so could result in serious personal injury in an accident Seat belt assemblies not in use during a colli sion should also be replaced if either damage or improper operation is noted Seat belt pre tensioner should be replaced even if the seat belts are not in use during a frontal collision in which the air bags are deployed Replace any seat belt assembly including anchor bolts if e The seat be
7. fer to DI 95 Seat Belt Buckle Switch Driver Side Signal Inspection SEAT BELT WARNING LAMP e Fasten driver s seat belt e The seat belt warning lamp should go out e Ifthe seat belt warning lamp does not go out Refer to DI 62 Wiring Diagram WARN Removal and Installation of Seat Belt Coupe wrtsooa0s SEC 868 Retaining washer E AV Spacer x 4 Via A ja Anchor bolt 0 43 1 54 9 4 4 5 6 32 40 pre tensioner connector Spring washer Pai Retaining washer Anchor bolt 2 0 43 1 54 9 f 4 4 5 6 32 40 JA SI spacer A 7 Anchor bolt 43 1 54 9 0 Nem kg m ft lb a 4 4 5 6 32 40 PHIA0530E CAUTION Before servicing SRS turn the ignition switch OFF disconnect both battery cables and wait at least 3 minutes REMOVAL OF SEAT BELT RETRACTOR 1 Remove the shoulder anchor cover on the seat belt anchor 2 Remove the anchor bolt 3 Slide up outer anchor cover and remove the anchor bolt 4 Remove the rear side finisher and rear pillar finisher Refer to El 35 Removal and Installation for Coupe Models 5 Remove the center console Refer to IP 10 Component Parts Drawing 6 Remove the luggage floor finisher lower Refer to El 39 Removal and Installation for Coupe Models 7 Remove the woofer and woofer amp BOSE system bracket mounting bolts Refer to AV 47 Removal and Installation of Woofer and Woofer Amp BOSE System 8 Remove
8. lt was in use at the time of a collision except for minor collisions and the belts retractors and buckles show no damage and continue to operate properly The seat belt was damaged in an accident i e torn webbing bent retractor or guide e The seat belt attaching point was damaged in an accident Inspect the seat belt attaching area for damage or distortion and repair as necessary before installing a new seat belt assembly e Anchor bolts are deformed or worn out e The seat belt pre tensioner should be replaced even if the seat belts are not in use during the collision in which the air bags are deployed PRELIMINARY CHECKS 1 Check the seat belt warning lamp chime for proper operation as follows a Switch ignition ON The seat belt warning lamp should illuminate Also the seat belt warning chime should sound for about 6 seconds b Fasten driver s seat belt The seat belt warning lamp should go out and the chime if sounding should stop 2 If the air bag warning lamp is blinking conduct self diagnosis using CONSULT II and confirm with air bag warning lamp Refer to SRS 21 SRS Operation Check 3 Make sure that the seat belt retractor seat belt anchor and buckle bolts are securely attached 4 Check the shoulder seat belt guide for seats Ensure guide swivels freely and that webbing lays flat and does not bind in guide Ensure height adjuster operates properly and holds securely 5 Check retractor operation a Fully e
9. t assembly including anchor bolts if e The seat belt was in use at the time of a collision except for minor collisions and the belts retractors and buckles show no damage and continue to operate properly e The seat belt was damaged in an accident i e torn webbing bent retractor or guide The seat belt attaching point was damaged in an accident Inspect the seat belt attaching area for damage or distortion and repair as necessary before installing a new seat belt assembly e Anchor bolts are deformed or worn out The seat belt pre tensioner should be replaced even if the seat belts are not in use during the collision in which the air bags are deployed Revision 2005 August SB 2 2006 350Z PRECAUTIONS Precautions for Battery Service wrtso0009 Before disconnecting the battery lower both the driver and passenger windows This will prevent any interfer ence between the window edge and the vehicle when the door is opened closed During normal operation the window slightly raises and lowers automatically to prevent any window to vehicle interference The automatic window function will not work with the battery disconnected Revision 2005 August SB 3 2006 350Z SEAT BELTS SEAT BELTS PFP 86884 System Description wrtso0004 SEAT BELT WARNING CHIME e With ignition switch turned ON and seat belt unfastened seat belt switch ON warning chime will sound for approximately 6 seconds e f warning chime does not sound Re
10. the rear floor box Refer to El 39 Removal and Installation for Coupe Models Revision 2005 August SB 4 2006 350Z SEAT BELTS 9 Disconnect the seat belt pre tensioner connector CAUTION Screwdriver e For installing removing pre tensioner seat belt connec tor insert screwdriver wrapped in tape into notch lift nio k lock and remove connector e Install connector with lock raised and push lock into connector PHIA0341E 10 Remove the seat belt pre tensioner retractor fixing screw and anchor bolt and then remove the seat belt retractor INSTALLATION OF SEAT BELT RETRACTOR CAUTION Before servicing SRS turn the ignition switch OFF disconnect both battery cables and wait at least 3 minutes Install in the reverse order of removal REMOVAL OF SEAT BELT BUCKLE 1 Remove the seat Refer to SE 71 REMOVAL 2 Remove the screws and remove the seat cushion inner finisher 3 Remove the anchor bolt and remove the buckle Waving Spacer washer washer Anchor bolt 0 43 1 54 9 Nem Seat belt buckle 4 4 5 6 kg m 32 40 ft Ib sae INSTALLATION OF SEAT BELT BUCKLE Install in the reverse order of removal Revision 2005 August SB 5 2006 350Z SEAT BELTS Removal and Installation of Seat Belt Roadster NHSO0006 oF gt A 0 49 0 5 0 36 ee 0 49 0 5 0 36 0 Nem kg m ft lb PHIA0458E Sash guide 2 Screw 3 Seat belt pre tensioner connector Spring washer 5
11. uld lock and not be extended If the seat belt retractor assembly does not lock perform the retractor off vehicle check SEAT BELT RETRACTOR OFF VEHICLE CHECK 1 Remove the seat belt retractor assembly 2 Slowly pull out webbing while tilting the retractor assembly for 15 degrees or 35 degrees or ward from the mounted position without twisting the retractor less tit more tilt assembly as shown in the figure j 15 degrees or less tilt Webbing can be pulled out 35 degrees or more tilt Webbing locks and cannot be pulled out If NG replace the retractor assembly Mounted position Tilt the seat belt retractor forward from the mounted position without twisting the retractor PHIA0175E Revision 2005 August SB 9 2006 350Z SEAT BELTS Revision 2005 August SB 10 2006 350Z
12. xtend the seat belt webbing and check for twists tears or other damage b Allow the seat belt to retract Ensure that webbing returns smoothly and completely into the retractor If the seat belt does not return smoothly wipe the inside of the loops with a clean paper cloth because dirt built up in the loops of the upper anchors can cause the seat belts to retract slowly c Fasten the seat belt Check the seat belt returns smoothly and completely to the retractor If the webbing does not return smoothly the cause may be an accumulation of dust or dirt Use the SEAT BELT TAPE SET and perform the following steps Inspect the seat belt through anchor 1 Pull the seat belt out to a length of 500 mm 19 69 in or more 2 Use aclip or other device to the fix the seat belt at the rear side finisher webbing opening 3 Pass a thin wire through the through anchor webbing opening Hold both ends of the wire and pull taut while moving it up and down several times along the webbing opening surface to remove dirt 4 Any dirt that cannot be removed with the wire can be removed by cleaning the opening with a clean cloth 5 Apply tape at the point where the webbing contacts the through anchor webbing opening NOTE Apply the tape so that there is no looseness or wrinkling 6 Remove the clip fixing the seat belt and make sure that the webbing returns smoothly 7 Repeat steps above as necessary to check the other seat belts Revision 2005
Download Pdf Manuals
Related Search