Service Manual
Contents
1. 6 INSTALL REAR WHEEL OPENING EXTENSION PAD NO 1 a Install the front wheel opening extension pad No 2 to the front fender moulding LH using double sided tape 7 INSTALL QUARTER OUTSIDE MOULDING LH a Using a heat gun heat both the quarter outside moulding LH and the surface of the body REAR WHEEL OPENING EXTENSION PAD NO 1 B147247J01 DR AN b Attach the 5 claws and install the quarter outside moulding LH Protacive Tape T c Connect the 2 screws and the 3 clips and attach it thoroughly NOTICE Be careful not to touch the adhesive surface with your fin gers when removing the exfoliate paper from the double sided tape B137909J01 8 INSTALL OUTSIDE MOULDING RETAINER NO 3 LH a Install the outside moulding retainer No 3 LH with the 3 screws B137923 ET 32 BODY EXTERIOR QUARTER PANEL WHEEL OPENING MOULDING LH REAR WHEEL OPENING EXTENSION PAD NO 2 B137921 B137922 B137925 9 10 11 INSTALL REAR WHEEL OPENING EXTENSION PAD NO 2 a Install the rear wheel opening extension pad No 2 to the rear wheel opening extension No 1 LH with double sided tape INSTALL REAR WHEEL OPENING EXTENSION NO 1 a Using a heat gun heat both the rear wheel opening extension No 1 LH and the surface of the body Connect the 2 claws and the screw and firmly press the exten sion to the vehicle body NOTI2. the tape using a rag or piece of cloth b Clean the surface with a solvent CLEAN QUARTER OUTSIDE MOULDING AND REAR WHEEL OPENING EXTENSION WHEN REUSING a CLEAN DOUBLE SIDED TAPE INSTALLATION SURFACE 1 Heat the double sided tape that remains on the quarter outside moulding and the rear wheel opening extension using a heat gun 2 While heating the tape with the heat gun use a rag or piece of cloth to wipe off the double sided tape remaining on the quarter outside moulding and the rear wheel open ing extension NOTICE e Remove as much of the double sided tape as pos sible Any tape that remains may cause attach ment failure when the quarter outside moulding and the rear wheel opening extension are installed BODY EXTERIOR QUARTER PANEL WHEEL OPENING MOULDING LH ET 31 e Use a waste cloth to scrub off because it may cause damage and attachment failure if using a driver 3 Clean the surface with a solvent 3 INSTALL MOUNTING BRACKET NO 1 a Install the 2 screws and mounting bracket No 1 NOTICE Do not confuse mounting bracket No 1 with mounting bracket No 2 The parts look alike 4 INSTALL MOUNTING BRACKET NO 2 a Install the 2 screws and mounting bracket No 2 NOTICE Do not confuse mounting bracket No 2 with mounting bracket No 1 The parts look alike B137910J01 5 INSTALL OUTSIDE MOULDING CLIP NO 4 a Install the outside moulding clip No 4 to the quarter outside moulding LH
3. CE Be careful not to touch the adhesive surface with your fin gers when removing the exfoliate paper from the double sided tape Install the rivet 1 Put nose piece No 2 on the riveter 2 Using the riveter install a new rivet Operate the riveter while holding it perpendicular to the rivet hole INSTALL MOULDING COVER NO 1 a Engage the 2 claws and install the moulding cover No 1
4. ET 28 BODY EXTERIOR QUARTER PANEL WHEEL OPENING MOULDING LH QUARTER PANEL WHEEL OPENING MOULDING LH COMPONENTS REAR WHEEL OPENING EXTENSION NO 1 RH MOULDING y COVER NO 1 QUARTER OUTER REAR WHEEL OPENING SIDE MOLDING RH EXTENSION PAD NO 1 REAR WHEEL OPENING EXTENSION PAD NO 1 OUTSIDE MOLDING RETAINER NO 2 RH _ D e aad MOUNTING P _ aae T BRACKET a a NO 1 MOUNTING BRACKET NO 2 REAR WHEEL OPENING REAR EXTENSION NO 1 LH OUTSIDE MOLDING RETAINER NO 3 LH Tne WHEELOPENING d L EXTENSION PAD ee o MOULDING COVER NO 1 D NO 2 UTSIDE MOLDING CLIP NO 4 QUARTER OUTSIDE MOLDING LH REAR WHEEL OPENINGEXTENSION NON REUSEABLE PART PAD NO 2 B141276J01 ET 29 BODY EXTERIOR QUARTER PANEL WHEEL OPENING MOULDING LH i B137925 B137922J01 B137921 B137923 REMOVAL REMOVE MOLDING COVER NO 1 a Disengage the 2 claws and remove the moulding cover No 1 REMOVE REAR WHEEL OPENING EXTENSION NO 1 LH a b Apply protective tape as shown in the illustration Remove the rivet 1 Wrap tape around the drill bit leaving approximately 5 mm from the tip of the drill bit as shown in the illustration HINT The purpose of wrapping the tape around the drill bit is to prevent the drill from drilling too deep 2 Apply and hold the drill to the rivet Drill the rivet flange area and remove th
5. e rivet Heat the rear wheel opening extension No 1 using a heat gun Remove the screw disengage the cllips and remove the rear wheel opening extension No 1 LH REMOVE OUTSIDE MOULDING RETAINER NO 3 LH a Remove the 3 screws and the outside moulding retainer No 3 LH REMOVE REAR WHEEL OPENING EXTENSION PAD NO 1 a Remove the rear wheel opening extension No 1 from the rear wheel opening extension No 1 LH BODY EXTERIOR QUARTER PANEL WHEEL OPENING MOULDING LH N Protective Tape q B137909J01 B137911 B137910J01 5 REMOVE QUARTER OUTSIDE MOULDING LH a Apply protective tape as shown in the illustration b Remove the 2 screws and the 3 clips c Heat the quarter outside moulding RH using a heat gun d Disengage the 5 clips and remove the quarter outside moulding RH REMOVE OUTSIDE MOULDING CLIP NO 4 a If the outside moulding clip No 4 remains on the vehicle side turn it to about 90 and remove it as shown in the illustration REMOVE MOUNTING BRACKET NO 1 a Remove the 2 screws and mounting bracket No 1 REMOVE MOUNTING BRACKET NO 2 a Remove the 2 screws and mounting bracket No 2 REMOVE REAR WHEEL OPENING EXTENSION PAD NO 2 a Remove the rear wheel opening extension pad No 2 from the quarter outside moulding INSTALLATION 1 CLEAN INSTALLATION SURFACE a Heat the double sided tape on the body using a heat gun Then wipe off
Download Pdf Manuals
Related Search