BOOM! AUDIO AM/FM/WB HIDDEN ANTENNA - Harley
Contents
1. 51B on back of radio Antenna wire Cigarette lighter Antenna black wire Antenna red wire Antenna end 2 Cable strap base 8 10 Cable strap 8 Figure 2 Antenna Element Routing FLHT Models with LED or Dual Bulb Headlamp PHONAAAYNS Models with Frame Mounted Fairing 1 See Figure 4 Get the antenna 1 foam tape 6 and alcohol cleaning packet 7 from the kit Remove the mounting wedge 3 from the antenna housing 2 Recycle or dispose of the wedge and screws 4 properly 2 See Figure 3 Test fit the antenna 1 against the underside of the fairing mount bracket 2 with the power and ground leads facing forward 3 Clean the mounting area of the fairing mount bracket and antenna with the alcohol wipe Allow to dry thoroughly 4 Remove the liner from the adhesive backing on one side of the foam tape Fasten the tape to the antenna 5 Remove the liner from the adhesive backing on the second side of the foam tape Carefully position the antenna to the inner fairing as high as it will go against the fairing mounting brackets Press firmly into place Hold the antenna in position with steady pressure for one minute Proceed to ALL models 20f5 is07164 Antenna Fairing mount bracket Antenna port 51B on back of radio Antenna wire Cigarette lighter Antenna black wire Antenna red wire Antenna end 2 Cable strap base 8 10 Cable strap 8 Figure 3 Antenna Ele2. About 1 4 in 6 mm Figure 1 Antenna Element Routing FLHT Models with Standard Headlamp Clean the mounting area of the skirt with the alcohol wipe Allow to dry thoroughly Remove the liner from the adhesive backing of the foam tape on the wedge Carefully position the antenna to the fairing skirt and press firmly into place Hold the antenna in position with steady pressure for one minute Proceed to ALL models Models with Fork Mounted Fairing and LED or Dual Bulb Halogen Headlamp 1 See Figure 4 Get the antenna 1 foam tape 6 and alcohol cleaning packet 7 from the kit Remove the mounting wedge 3 from the antenna housing 2 Recycle or dispose of the wedge and screws 4 properly See Figure 2 Test fit the antenna 1 against the inside of the inner fairing under the cigarette lighter 5 with the power and ground leads facing upward Clean the mounting area of the inner fairing and antenna with the alcohol wipe Allow to dry thoroughly Remove the liner from the adhesive backing on one side of the foam tape Fasten the tape to the antenna Remove the liner from the adhesive backing on the second side of the foam tape Carefully position the antenna to the inner fairing beneath the cigarette lighter Press firmly into place Hold the antenna in position with steady pres sure for one minute Proceed to ALL models J05554 is07165a Antenna Outer fairing skirt Antenna port
3. text but not included in kit A Black antenna ground wire B Red antenna power wire C Antenna element 2 D Antenna end 2 J05554 5of5
4. cMOTOR HARLEY DAVIDSON WY J05554 INSTRUCTIONS REV 2011 11 11 BOOM AUDIO AM FM WB HIDDEN ANTENNA GENERAL Kit Number 76000266 Models For model fitment information see the P amp A retail catalog or the Parts and Accessories section of www harley davidson com English only Installation Requirements WARNING The rider s safety depends upon the correct installation of this kit Use the appropriate service manual procedures If the procedure is not within your capabilities or you do not have the correct tools have a Harley Davidson dealer perform the installation Improper installation of this kit could result in death or serious injury 00333a NOTE This instruction sheet refers to service manual information A service manual for this year model motorcycle is required for this installation and is available from a Harley Davidson dealer Kit Contents See Figure 4 and Table 1 PREPARATION NOTE For vehicles equipped with security siren 2007 and later Verify that the Hands Free Fob is present Turn the ignition key switch to IGNITION e 2006 and earlier Disarm the siren with the key fob WARNING To prevent accidental vehicle start up which could cause death or serious injury remove main fuse before pro ceeding 00251b 1 See the service manual and remove the main fuse 2 Turn the ignition key switch OFF NOTE For models with fork mounted fairing removing the headlamp
5. from the fairing now may simplify fairing installation with the antenna in place 3 See the service manual to remove the outer fairing and windshield J05554 amp Many Harley Davidson Parts amp Accessories are made of plastics and metals which can be recycled INSTALLATION Follow the installation and routing instructions carefully to obtain the best possible performance from the antenna NOTES e Ambient temperature should be at least 60 F 16 C for proper adhesion of the hidden antenna to the vehicle e Allow AT LEAST 24 hours after applying the antenna before exposing the area to vigorous washing strong water spray or extreme weather e The adhesive bond will increase to maximum strength after about 72 hours at normal room temperature Models with Fork Mounted Fairing and Standard Headlamp 1 See Figure 4 Get the antenna 1 and alcohol cleaning packet 7 from the kit 2 See Figure 1 Position the curved mounting wedge of the antenna 1 against the front of the vehicle outer fairing skirt 2 about 1 4 in 6 mm below the black plastic trim strip with the power and ground leads facing up 1 of 5 Please dispose of materials responsibly isO7165 Antenna Outer fairing skirt Antenna port 51B on back of radio Antenna wire Cigarette lighter Antenna black wire Antenna red wire Antenna end 2 Cable strap base 8 10 Cable strap 8 OHMNAAARYNS 11
6. ment Routing FLTR Models ON OO PO ALL Models NOTE Electrical connectors are identified in the service manual by the numbers and letters shown here within brackets 6 See Figure 1 Figure 2 or Figure 3 Unplug the original equipment OE antenna connector 51 A from the antenna port 51B 3 on the back of the radio Secure the antenna cable out of the way inside the fairing 7 Route the antenna wire 4 and connector on the new antenna to the radio and plug the connector into the antenna port NOTES Make the connections to the cigarette lighter 5 one lead at a time to prevent crossing the connections which could damage the antenna Having more than one accessory connected to the terminal mounting tabs on the cigarette lighter terminals could lead to a short in the accessory circuit References to the orange white wire in the following steps apply also to the orange red cigarette lighter power wire found in some applications 8 If NO additional accessory is currently connected to the cigarette lighter terminal mounting tabs 132A J05554 Connect the antenna to the cigarette lighter terminals as follows a Unplug the black wire terminal 132B from the cigar ette lighter Connect it to the tab on the antenna black wire 6 terminal b Connect the antenna black wire terminal to the cigarette lighter ground terminal c Unplug the orange white wire terminal 132B from the cigarette ligh
7. nction The red LED on the antenna body 2 should illuminate with the ignition key switch in the ACCY or IGN position If it does not check the inline fuse 5 on the red antenna power wire or the vehicle accessory fuse NOTE Installation of the hidden antenna can result in a slight reduction of AM signal reception in certain urban and rural locations 3 Test the radio function on the AM FM and Weather bands to verify that the antenna is working properly See the service manual to install the outer fairing and windshield For models with fork mounted fairing install the head lamp if removed earlier 4of5 SERVIC E PARTS is07173 a AN E A Figure 4 Service Parts Boom Audio Hidden AM FM WB Enhanced Reception Antenna Table 1 Service Parts Item Description Quantity Part Number 1 Antenna AM FM WEB includes items 2 5 Not sold separately 2 e Antenna Not sold separately 3 e Wedge mounting for FLH models Not sold separately 4 e Screw pan head 6 2 Not sold separately 5 e Fuse mini type 2 Amp gray 54305 98 6 Foam tape two side adhesive 11100063 7 Alcohol cleaning packet Not sold separately 8 Sealed splice connector 14 16AWG blue 2 70586 93 9 Wire retainer adhesive back 8 Not sold separately 10 Cable strap 10 10065 11 Thread protector cap antenna base Not sold separately 12 Plug fascia antenna hole 59749 06 Items mentioned in
8. s 10 from the kit as follows a Use the alcohol wipe along the antenna element path to clean the mounting areas for the cable strap bases and antenna ends approximately as shown Allow to dry thoroughly b Remove the liner from the adhesive backing of the antenna end 8 Position the end to the inner fairing and press firmly into place c Remove the liner from the adhesive backing of a cable strap base Position the base to the inner fairing and press firmly into place d Use a cable strap to tie the antenna element to the base Do not overtighten e Repeat for the remaining cable strap bases and cable straps on that side of the inner fairing Route the antenna element on the opposite side of the inner fairing and secure with cable strap bases and cable straps in the same manner 3 of 5 12 13 Use cable straps from the kit to secure the excess hidden antenna wiring as necessary For FLHX and FLTRX Models Remove the grommet from the antenna clearance hole in the fascia Install the hole plug 12 from the kit For ALL Models Remove the OE AM FM antenna mast from the rear of the vehicle Install the antenna thread protector 11 over the antenna base RETURN TO SERVICE NOTE To prevent possible damage to the sound system verify that the ignition key switch is in the OFF position before installing the main fuse 1 See the service manual and install the main fuse J05554 Check for antenna fu
9. ter Connect it to the tab on the antenna red wire 7 terminal d Connect the antenna red wire terminal to the cigarette lighter power terminal If an accessory IS already connected to the cigarette lighter terminal mounting tabs 132A See Figure 4 Splice into the power orange white and ground black wires to connect the antenna as follows a Cut the connectors from the black A and red B wires of the antenna and strip approximately 3 8 in 10 mm of insulation from the end of each wire b Cut the black wire leading to the cigarette lighter approximately 1 in 25 mm back from the connector Strip approximately 3 8 in 10 mm of insulation from the end of each black wire c Follow instructions in the service manual appendix to splice the black wire of the antenna to the two ends of the cut black ground wire using a sealed splice connector 8 from the kit d Cut the orange white wire leading to the cigarette lighter in the same manner Splice the red wire of the hidden antenna to the two ends of the cut orange white wire using a sealed splice connector NOTE On FLHT models with LED or dual bulb headlamp Figure 2 Route the end of the clutch lever side antenna element forward on the fairing vertical support bracket 9 10 11 Route the antenna element C on one side of the inner fairing as shown in Figure 1 Figure 2 or Figure 3 Secure the antenna element with cable strap bases 9 and cable strap
Download Pdf Manuals
Related Search