Ticket Troopers 2
Contents
1. Ticket Troopers Page 17 Troubleshooting Guide Troubleshooting Strategy Use common sense and a systematic method of troubleshooting to determine the exact problem probable cause and remedy Use the process of elimination to find the faulty component Always check for the simple and obvious causes first such as unplugged loose or broken wires and bad sensors bent pinched stuck or jammed components a Check wall outlet b Check transformer fuse 220v applications only 7 a Unplugged amp fast burn b Blown Fuse c Reset power strip breaker switch or building circuit c Circuit breaker tripped breaker Attempt to determine cause Bowe Monier dams d Power strip turned off d Check Power strip it is e Bad power supply located under main board f AC in line filter faulty e See power supply diagnostic Replace if faulty A5PS1001 f Replace AC filter A5FI9222 a Increase the volume at any of the player station doors b Check audio cable connections to speaker and main circuit board Check continuity a Volume too low b Loose wire at control or speaker No Audio Replace main board with e UE E oar board from another Gen 5 ma UNGON game if possible to isolate the problem to the main circuit d Door interface board faulty board d Replace door interface board with working station board Service Manual Ticket Troopers Page 18 Troub2. D 3 4 5 D 18 19 20 The most common reason for a sensor failure is that the emitter and detector pair is slightly out of alignment Simply adjust the pair to see each other better If the error still exists you may need to replace the pair Contact Bay Tek Games Service at 920 822 3951 Ex 1102 Service Manual Ticket Troopers Page 15 Other Error Codes Probable Solution Playfield motor moving too slow or not moving at all Playfield motor moving too fast No player position selected for the target assembly Player Station Error Codes Check the power going to the motor Replace the motor or sensor Check the wiring to the motor sensor Replace the sensor Use the dips on the target assembly to set the player station see page 10 Probable Solution Coin accepter signal stuck ON for Trooper 1 Coin accepter signal stuck ON for Trooper 2 Coin accepter signal stuck ON for Trooper 3 Reset ticket button stuck ON for Trooper 1 Reset ticket button stuck ON for Trooper 2 Reset ticket button stuck ON for Trooper 3 Service Manual Ticket Troopers Check the wiring to the coin comparator Replace if needed Check the wiring to the coin comparator Replace if needed Check the wiring to the coin comparator Replace if needed Check the wiring to the button Replace if needed Check the wiring to the button Replace if needed Check the wiring to the
3. Factory Default Settings Factory Settings Bank 1 Factory Settings Bank 2 Dip 1 Dip 2 Dip Dip 4 Die 5 oie e Die 7 Dip 8 Die oio 2 3 Dip 5 Die 7 OFF OFF OFF orr OFF OFF 1 Service Manual Ticket Troopers Page 6 Ticket Payout Select Standard Ticket Patterns Chart BANK 1 DIP 6 1 Ticket Payout Select Allows you to choose between a standard ticket OPTIONS ayout a fixed ticket payout Fixed Ticket Standard Pattern see charts 2 5 Fixed Pattern see chart 6 Standard Factory Setting Standard Ticket Payout Ticket Payout BANK 2 DIP 5 DIP6 DIP 7 Standard Ticket Patterns Ticket Amount 5 Tickets 3 Tickets Drain 4 Tickets i EMG Outside EI 1 Ticket Drain 3 Tickets 1 Ticket Once you have chosen the 6 Tickets 2 Tickets pattern see the charts below to Outside Drain set the bonus ticket number 3 Tickets Factory Default Setting 7 Outside Drain Inside Note If you choose a different standard pattern other then the factory default you will need to contact Bay Tek Games parts department for a new ticket decals for the target assemblies Inside 6 Tickets Inside 3 Tickets Inside 2 Tickets Inside 4 Tickets Inside 10 Tickets off Service Manual Ticket Troopers Page 7 Bonus Ticket Select C
4. I DR 1 I E ta gt gt 2 NORD E an 1 Foe I UR RSS 1 ates 1 1 F 1 on or h 1 1 1 ny 1 meus Service Manual Ticket Troopers Page 32 Power Section 18 F Service Manual JI Ba Ix 44 3 4 10 id B Ji 1 3 Ticket Troopers Page 33 Processor Section Input RD age bles V G 2 ws m isal 1 inl em eru 1 e n E e 11 5 mat 2 gt 1 45 d 5 eed Shas ie 1 1 A 4 L 4 7 Service Manual Ticket Troopers Page 34 Technical Support Know Your Options Excellent Customer Service is very important to Bay Tek We know that keeping your games in great operating condition is important to your business When you need us we are here to help You can call us for free technical assistance and you can count on us to have parts on hand to support your game When you do need us its important that you know what to expect We offer options that fit your needs Electronics Circuit Boards rhe Repair amp Return If you have Circuit Board issues with your B
5. still using the 1 2 wrench 3 Unscrew the turn table from the shaft 4 Unbolt the motor box from the game using the 7 16 wrench 5 Remove the pulley from the shaft using the 2mm Allen wrench 6 Remove the motor using the 5 16 wrench 7 Reassembly the motor box with the replacement motor Service Manual Ticket Troopers Helicopter Motor Tools Needed Drill with a 2 square bit 1 8 Allen wrench 5 16 wrench 1 Remove the shirt using the drill 2 Remove the helicopter mounting arm using the 1 8 Allen wrench 3 Unbolt the motor using the 5 16 wrench 4 Replace the motor and reassemble the unit Page 22 Service and Repair CAUTION Electric Shock Hazard 3 Before installing the new board check to be sure Do not perform repairs or maintenance the new dipswitches are set on this game with the power ON Note If swapping the board with a spare remember Unplug the unit from the wall outlet or shut off to also swap the programming chips Use extreme power at the power strip inside the game care to prevent static build up and prevent bending the chip pins CAUTION Static electricity could harm circuit boards and processor chips Always ground yourself by cable 4 Install the new board and reconnect the cables or by touching a metal surface prior to working on the game 5 Turn power back on and test the game Main Circuit Board Replacing the main Gen 5 board 1 With the power off carefully unpl
6. 9 rom ot luF up D e 27 Communications Serial EEprom ESE in 11 2 ri Er a m REF l FHLI Klo 106 Input Section Control Switches 1 L gt is 3 4 Ba 5 AE T 5 ae E uin luF PML 10k RES 12 SYDE IW dP Service Manual Ticket Troopers Page 28 Input Section B Inputs RE RC 13 13 RAS D 13 15 RD7 D 13 17 REL c 13 19 RESD J3 20 REZ D 13 18 13 16 13 14 ncspi 13 5 J3 7 43 9 43 11 43 12 43 10 43 8 13 6 Service Manual Ticket Troopers Page 29 Output Section Chase lights Q13 Q16 Output section A Lbigbte 013 16 Service Manual Ticket Troopers g rA ra u m ops re bode 493 NNWN 3 e Fr TM 1 146 24 16 24 16 Page 30 Output Section B Q17 Q24 TED Dukgut actinn 8 E afr ento NE mnn na aE nb p ma ut a Service Manual Ticket Troopers TED 72 18 75 14 Page 31 Output Section C Q5 Q12 i rey 1 F 1 r So vtt r 11 T TP F L END is E 4 E m 154 47 T xc n
7. free of defects in workmanship and materials for a period of 6 months from the date of installation Bay Tek Games Inc will without charge repair or replace at it s option defective product or component parts upon notification to the factory service department Warranty replacement part s will be shipped immediately via ground service along with a Return Material Authorized RMA number for the return of defective part s Defective parts must be shipped back to Bay Tek Games unless otherwise instructed This warranty does not apply in the event of any misuse or abuse of the product or as the result of any unauthorized repairs or alterations The warranty does not apply if the serial number decal is altered defaced or removed from its original position Should your game need servicing determine the serial number from the decal on the back of the cabinet or the logic unit and call 920 822 3951 or email to SERVICE BAYTEKGAMES COM Service Manual Ticket Troopers Repair of NON Warranty Units Should your game need servicing determine the serial number from the decal on the back of the cabinet or the logic unit and call 920 822 3951 or email to SERVICE BAYTEKGAMES COM An estimate of the repair charges will be quoted to you for approval You can proceed in one of two ways 1 Request the immediate shipment of advanced replacement part s You will receive the part s with an RMA for the return of the fa
8. the coins used in the game room preferable a new coin Page 4 Game Set Up Tools Needed None 1 Remove the Styrofoam bracing material from the helicopter 2 Unroll the power cord from the inside of the game and feed it thru the hole in the floor If your location is equipped with power from the ceiling the game has pre drilled holes to allow for an extension cord to be used 3 Move the game into position and lock all four casters 4 Plug in and power on Service Manual Ticket Troopers 5 Replace the Bay Tek test ticket with tickets of your own 6 Roll a few coins thru to ensure the comparators are working properly and that the correct amount of tickets are being paid out 7 Adjust the volume to suit your location To do so go to any player station ticket tray and hold down the red button until SND appears on all three of the displays Then tap the button to select desired volume level 1 8 Once done hold the button down again to return to play mode Page 5 Programming Section Programmable Options Important Power must be OFF to the game before adjusting the dip switches Turn OFF the power strip inside the game Set the desired settings wait 30 seconds the turn the power ON The ticket patterns attract mode and more are controlled by two banks of dipswitches located on the main circuit board The main circuit board is located in the sliding drawer located in the player 1 location
9. OE 10 Coins EBE AOE COOOL Service Manual Ticket Troopers Page 11 AABD8801 Target Assembly Located on the bottom of each target assembly Bank 1 Dip 1 DIP 2 DIP 2 Player Station Select Used to set the target for reson poston eosin Player whichever player station it Position Position Position assigned to It is set at the factory and should not be changed unless the target is moved or replaced Bank 1 Dip 4 Bank 1 Dip 5 Coin Hopper Equipped Player Door Cabling If the game is equipped with Dip 4 This dip allows earlier coin hoppers this dip must be Position used software to be upgraded d Use only at the direction of Hoppers Factory default is Dip 5 Position the Bay Tek service department No Hoppers TRA Factory Default is Remote pongo Bank 1 Dip 6 Emitter Detector Cluster 1 Control the power for Doa EDIT D29 D14 Position cluster 1 of emitters detectors D26 D11 D23 D8 Use only during troubleshooting 2 Power 1 7 Emitter Detector Cluster 2 Control the power for 028 013 Position cluster 2 of emitters detectors D25 D10 oe D22 07 Use only during troubleshooting Power On OFF Bank 1 Dip 8 Emitter Detector Cluster 4 Control the power for Tee Options DiRe D27 D12 Position cluster 3 of emitters detectors D24 D9 D21 D6 Use only during t
10. Thank you for your purchase of a Ticket Troopers Our Vision We Aspire To Be The Best In The World At Developing And Manufacturing Coin Operated Games For Our Customers EK Ciis Service Manual Ticket Troopers Page 1 Record this information for future reference Serial Number Located inside any of the player station door Date of installation Installed by Service 920 822 3951 EXT 1102 Parts 920 822 3951 EXT 1107 For 24 hour pricing and ordering please visit us on the web at www baytekgqames com Service Manual Ticket Troopers Page 2 Ticket Troopers ATTENTION OPERATORS PLEASE BE ADVISED TICKET TROOPERS GAME PLAY IS ADDICTIVE AND MAY CAUSE MAXIMUM EXCITEMENT OVER Ticket Troopers is a 3 player quick coin game with an exciting police theme The players aim the shooters and insert the coins aiming for the targets directly across The continuously spinning playfield adds excitement as the coin speeds across to the other side When a target is hit the game projects flashing red and blue lights If the player hits the center target the siren sounds as the player is awarded the big ticket bonus The spinning helicopter draws them in as the fast paced game play keeps them there Service Manual Ticket Troopers Page 3 OPERATION AND SET UP Safety Precautions CAUTION Electric Shock Hazard Do not perform repairs or maintenance on this game with the power ON Unplug the unit f
11. ay Tek game you can send the board to us and we ll repair it right away Most items sent to us are repaired and returned to you within one day This option is your best value as we offer this fast turn around service at the most reasonable price Advance Replacement If you have Circuit Board issues with your Bay Tek Call us M F game but you don t have time to send in your board for repair give us a call and Sam 5pm CST at ask for an Advance Replacement We ll send you out a replacement board that 920 822 3951 ext 1102 same This is your best option when you need to get your game up and run ning as quickly as possible When you get your new board just repackage the defective board the same box and send it back to us We make it easy by including a UPS Return Shipping label for you to put on the box Spare Parts Take matters into your own hands and purchase new spare Circuit Boards for your Bay Tek games Many of our games share the same main board electronics This means you can buy set of spare electronics to support many of your Bay Tek games Spare boards allow you to get your game Fax us at up and running the quickest and provide you a valuable troubleshooting option 920 822 1496 Call our technicians to get recommendations for what you should keep on hand for spare Technical Support You are the best tool for troubleshooting Your abilities to understand the game and your skills to
12. button Replace if needed Page 16 Preventive Maintenance Section Maintenance Chart Use the following maintenance chart as a guide only Actual maintenance intervals will depend on usage and environmental conditions at the location of the game Keep a log of all inspections even if no problem exists with date and time of inspection action taken A sample Repair Record form is included at the end of this manual CAUTION Use of flammable substances can cause severe burns or personal injury Always use non flammable solvents for cleaning parts and surfaces of this game Do not use flammable substances such as gasoline kerosene or thinners IMPORTANT Do not use denatured alcohol lacquer thinner or similar solvents to clean the conveyor belt as they will cause damage to the belt surface IMPORTANT The game should be shut OFF for cleaning and maintenance IMPORTANT Do not use cleaning solvents on game graphics Use only a mild soap solution and dry with a clean lint free cloth _____ De worthy Fill ticket trays Inspect game for physical damage Repair as necessary Inspect game lighting and replace lamps as necessary Clean outside surfaces and glass Empty cash box Open game and clean playfield and inner surfaces with a clean soft cloth and warm soapy water Do Not use solvents Test to insure game is working properly Blow ticket dust from ticket dispensers Service Manual
13. e the following procedure to check the Power supply for Gen 5 games Check the small green LED light on the power supply circuit board If the light is out there is a short somewhere If the light dims there is an overload in one of the circuits such as a bad motor Turn power OFF Disconnect all 12 volt output wires only Turn power ON Green LED Light Green LED Light comes ON remains OFF Replace Power Supply Turn power OFF Unplug all outputs from the Gen 5 Circuit Board Reconnect the 12 volt output wires to the Power Supply Turn power ON Green LED Light Green LED Light Short in Main Board comes ON remains OFF Replace That cable or related component Turn power OFF Green LED Light is shorted out See Jumper Cable Reconnect the outputs remains OFF Pin Outs to see which component at the Main Circuit might be at fault Board one at a time Wait 1 min between tests to turn power ON Green LED Light dims A related component such as a solenoid is causing an overload See Jumper Cable Pin Outs beginning on page 18 to see Green LED Light That cable is OK which component might be at comes ON fault Service Manual Ticket Troopers Page 21 Replacing Motors Turn Table Motor Tools Needed Medium Phillips Screwdriver 1 2 wrench 7 16 wrench 2mm Allen wrench 5 16 wrench 1 Remove the vacuum form piece from below any player station 2 Locate the shaft under the turn table and hold it
14. hart BANK 1 DIP 7 DIP 8 3 Bonus Ticket Select Bonus 8 Bonus ticket selection for standard 25 Tickets patterns 1 5 or 6 Factory Setting 50 Tickets 75 Tickets Chart BANK 1 DIP 7 DIP8 4 Bonus Ticket Select Bonus 30 Tickets Bonus ticket selection for standard pattern 2 90 Tickets BANK 1 DIP 7 DIP 8 Bonus Ticket Select Tickets Position Position Chart BANK 1 DIP 7 DIP 8 6 Bonus Ticket Select Tickets Position Position on Bonus ticket selection for standard Chart 5 Bonus ticket selection for standard patterns 3 or 4 250 Tickets 200 Tickets Service Manual Ticket Troopers Page 8 Fixed Ticket Patterns Chart BANK 1 DIP 1 DIP 2 DIP 3 DIP 4 7 Fixed Ticket Patterns Ticket If you decide to go with the fixed ticket pattern you may choose to 7 Tickets set the amount of tickets won The game will pay out the selected 8 Tickets amount when a coin is inserted regardless if a target is hit senes ot DICZERESERES Service Manual Ticket Troopers Page 9 Mercy Ticket Attract Mode Wheel Feedback Door Cabling Echo Testing Chart BANK 2 DIP 2 DIP3 Mercy Ticket Tickets The game will payout the selected ticket amount for every play 0 Tickets regardless if a target is scored 4 Ticket 2 Tickets Factory Sett
15. ing 0 Tickets 3 Tickets Bank 2 Dip 8 Attract Mode The attract mode will activate game lighting and Options Dips play selected tracks from the audio file every 5 minutes when the game isn t being played Enabled E Factory Setting Enabled disabled Bank 2 Dip 4 Wheel Feedback Door Cabling Chart 10 Allows the software to identify certain revisions to Options the game This dip should not be used unless otherwise instructed by the Bay Tek service department Factory Setting Disabled Disabled Bank 2 Dip 1 Echo Testing This dip should not be used unless otherwise instructed by the Bay Tek service department embed Factory Setting Disabled Disabled Service Manual Ticket Troopers Page 10 Half Ticket Payout Coin Hopper Equipped Bank 1 Dip 5 12 Half Ticket Payout Allows the game to pay half of the tickets won It can only be used on standard patterns 2 and 5 Also on fixed ticket patterns where the tickets won Half Tickets can be divided by 2 Factory Setting Full Tickets Full Tickets OFF Chart BANK 1 DIP 1 DIP 2 DIP 3 DIP 4 13 Coin Hopper Equipped Coins per AOE CARIE If the Ticket Troopers is coin hopper equipped and uses card readers you can 7 Coins set the number of coins each player receives with every swipe their card 8 You must also set the dips on each target assembly board AABD8801 O
16. leshooting Guide Lighting not functioning Turntable not turning Helicopter motor does not turn Service Manual a Burned out lamp b Wiring damaged or disconnected c Lamp socket damaged or disconnected a Toggle power switch is off b Does motor turn at power up then stop c Check for 12 Volts DC at motor immediately after power on d Main circuit board malfunction a Toggle power switch is off b Check for 12 Volts DC at motor immediately after power on c Check for plastic gear binding d Main circuit board malfunction Ticket Troopers a Replace lamp with 26 Watt mini spiral bulb A5LI0001 b Check and repair wiring c Check and repair faulty sockets a Check position of toggle It is located inside Door 2 b Sensor does not see dull tab on bottom of table Remove table check sensor replace if needed AABD5010 c If 12 Volts is present replace motor AAMO8800 d Replace main board with board from another Gen 5 game if possible to isolate the problem to the main circuit board a Check position of toggle It is located inside Door 2 b If 12 Volts is present replace motor AAMO8801 c Replace broken or wore gear d Replace main board with board from another Gen 5 game if possible to isolate the problem to the main circuit board Page 19 Troubleshooting Guide Probable Cause Coin mech is not working Tickets do not di
17. repair the game are invaluable to us If you need help give us a call It s not easy to diagnose a game remotely by phone but our tech nicians do a great job They ll need your help to perform some troubleshooting steps and convey to them exactly what s happening with your game Be sure to have your game Serial Number when you call Email us 24 hours a day at service bay tek com Also order parts online at Returns amp Credits www bay tek com Sometimes the issue isn t what it seemed to be If you chose the Advance Re placement option and now need to return that circuit board just give us a call to get Return Authorization You will be credited for the cost of the board and charged only the bench fee for our processing and retesting that board If you choose the Repair and Return option we ll test your board before we begin If no problems are found you will only be charged the bench fee Note Bench fees apply regardless of whether the repair was your choice or a recommendation from a Bay Tek technician It s a small price to pay for trouble Send parts to shooting the issues with your game 1077 E Glenbrook Dr Pulaski WI 54162 You can count our Technical Team for service and support BAY ATEK Service Manual Ticket Troopers Page 35 Warranty Information Bay Tek Games Inc warrants to the original purchaser that the game will be
18. rom the wall outlet or shut off power at the power strip inside the game CAUTION Electric Shock Hazard Always plug game into grounded circuit CAUTION Use of flammable substances can cause severe burns or personal injury Always use non flammable solvents for cleaning parts and surfaces Do not use substances such as gasoline kerosene or thinners Unpacking Assembly and Installation Inspect the game for any damaged loose or missing parts If damage is found please contact the carrier first Then contact Bay Tek Games at 920 822 3951 or service baytekgames com to order replacement parts AN back neck and other injuries Be sure adequate lifting and moving devices CAUTION Lifting Hazard Lifting heavy objects can cause are available when unloading unpacking and moving this game Marquee Installation Tools required 7 16 Socket 1 Remove the fully assembled marquee from the inside of the game Unpackaged it Service Manual Ticket Troopers 2 Place the marquee on top of the cabinet 3 Plug in marquee cables to the cables coming from the top of the game 4 Snap excess cabling into the cable clamps 5 Secure the marquee using the provided silver bolts and lock washers Line up with the holes in the top of the cabinet Set up of Coin Comparators If equipped Tools needed None 1 Remove the cover over the coin comparator 2 Slide the coin holder back and insert one of
19. roubleshooting 5 Service Manual Ticket Troopers Page 12 Error Codes How To Read The Codes Ticket Troopers is programmed with several error codes to help identify problems with your game The codes will appear on the target assembly that is affected at power up Use the pictures below to identify the issue The first number The second indicates the number indicates sensor hole with the sensor cluster the issue failing Service Manual Ticket Troopers Page 13 Error Codes Each target hole has a number assigned to it That number is the first number of the error code Emitter Detector Clusters Cluster 1 D32 D17 D29 D14 D26 D11 D23 D8 D20 D5 D6 D3 Cluster 2 D31 D16 D28 D13 D25 D10 D22 D7 D19 D4 D5 D2 Cluster 4 D30 D15 D27 D12 D24 D9 D21 D6 D18 D3 D4 D1 If more then one cluster is failing the program will add the numbers together to indicate the failing clusters EX If cluster 1 and cluster 4 are failing the program will show he number 5 See page 10 for dip assignments The second number is the failing cluster Those numbers are printed right on the AABD8801 and AABD8803 boards Service Manual Ticket Troopers Page 14 Sensor Error Code Chart The following chart will help you find the problem with the sensor clusters S BONUS os 3 BONUS 0940 02825 3 BONUS _D 11 10 D 26 25 D 8 7 6 D 23 22 21
20. spense Wrong amount of tickets dispensed Service Manual a Slide which holds coin is faulty b Coin speed dipswitch on mech c SW 1 dipswitch on mech d Faulty coin mech e Door interface board faulty a Disconnected loose or broken wires b Opto Sensor on ticket dispenser dirty c Faulty ticket dispenser d Notch on tickets cut too shallow e Door interface board faulty a Incorrect dipswitch settings b Game is scoring too soon before coin reaches sensor board c Cycle power off wait 30 seconds and power back on look for error code on display Ticket Troopers a Swap coins in mech Ensure slide clean and tight against coin b Ensure dip on the comparator is set to 100 ms c Ensure SW1 set to NC normally closed d Replace mech with working unit from different station e Replace door interface board with working station board a Check connectors Check for continuity b Blow dust from sensor and clean with isopropyl alcohol c Replace with working dispenser to isolate the problem d Flip tickets and load upside down to have large cut notch toward opto sensor e Replace door interface board with working station board a Check settings on main Gen 5 board b Sensor board is bad Align clean sensors replace board AABD8801A AABD880 3 c Refer to Error Codes section in manual Page 20 Troubleshooting Guide Us
21. ug the various connectors black chase light cables and white or grey display cables 2 Remove the four screws holding the board to the drawer Software Chip Service Manual Ticket Troopers Page 23 Electrical Drawing Section 1 4 EL 4 i J1 Connector RED 12v Input BLACK 12v Ground J2 Connector RED 12v Input RED BLACK Left Right Channel Channel BLACK 12v Ground GREEN YELLOW Left Right Channel Channel Service Manual Ticket Troopers Page 24 J4 Connector Service Manual BLACK Ticket Meter RED Meter Power WHITE Game Meter BLACK RPM Sensor RPM Grnd Signal 1 Ticket Troopers Page 25 J5 Connector Service Manual BLACK Chopper Grnd RED Wheel Motor Power RED Chopper Motor Power BLACK Wheel Ground Ticket Troopers Page 26 Gen 5 Main Board Schematics cle i 12 5VDC luF ENSE 11 n 1 18 AD 0 PAGE 2 oh NN IPLE FN 10 anti 4 I DOE 164 21 a 1 ___ 2 7 G_8002DC BE dr L ADLE HL ADLE T 5 EDLE gt 5 PROM Apc 1 5k CE5 0022uF 2 Service Manual Ticket Troopers 10 0 ab 55 Eha Ths hs
22. ulty part s You must return the faulty parts in 14 days to avoid additional charges 2 Send in the defective part s for repair or replacement Please include the following information Name Address Phone Number Serial Number Purchase Order Number or Signed Authorization to perform service Repair and returned parts will be shipped back using the same mode of transportation in which they were received Repairs are warranted 30 days from the date installed into service Page 36 Repair Record Make copies of this page for the future Game Serial Number Date Maintenance Performed Parts Replaced Notes Service Manual Ticket Troopers Page 37 Repair Record Make copies of this page for the future Game Serial Number Date Maintenance Performed Parts Replaced Notes Service Manual Ticket Troopers Page 38 Parts List Always use genuine Bay Tek Games replacement parts For 24 hour pricing and ordering please visit us at BAYTEKGAMES COM Part Number ES See SS SS Oe 58 8802 ASHA8800 5805000 ASL10001 Center Wheel Service Manual Ticket Troopers Page 39 Service Manual Ticket Troopers Page 40
Download Pdf Manuals
Related Search