XEROX® PHASER 3300
Contents
1. LY 3 Replacement drum 4 Replacement wiper blade 5 Conductive grease 6 Drum lubricating powder 1 Place the cartridge with the handle supply chamber facing 2 Gently pry off plastic drum axle bushing Keep this bushing you Remove the three screws on the right end cap with the appropriate end cap when removed Each side is different uninet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com XEROX PHASER 3300 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS 3 On the top edge of the end cap there is a plastic tab Press in on the tab and remove the right end cap 4 On the opposite side of the cartridge remove the three 5 Gently pry off plastic drum axle bushing Keep this bushing screws on the left end cap with the appropriate end cap when removed www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited F2. need to be cut off holes carefully drilled not too deep or the cartridge will leak and screws installed An interesting note on these machines according to the service manual the transfer roller is rated for 70 000 pages which is considered the lifetime of the machine However the paper pick up rollers are rated for 150 000 pages and the fuser 80 000 pages so the lifetime statement is a bit confusing The printers as well as the cartridges are listed below LY CARTRIDGE 106R01411 4 000 pages HY CARTRIDGE 106R01412 8 000 pages PRINTER Xerox Phaser 3300MFP Xerox Phaser 3300MFP X Pictured are the HY and LY cartridges As you can see they are identical So if you install the correct chip and toner load you can easily make a LY into a HY cartridge uniNnet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com XEROX PHASER 3300 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS REQUIRED TOOLS 1 Toner approved vacuum 2 A small common screwdriver 3 A Phillips head screwdriver 4 Needle nose pliers REQUIRED SUPPLIES 1 Xerox Phaser 3300 toner 2 Replacement chip HY or
3. ACTURING INSTRUCTIONS 34 Install the roller assembly 35 Install the right side end cap and three screws Make sure the top rear tab locks in place uniNnet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com XEROX PHASER 3300 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS 36 Press the drum axle bushing in place Set it so the small tab is at the end of the groove make sure it is fully seated The two small bushings are different Make sure you have the correct bushing for this side 37 Remove the tape from the gears and install the left side end cap and three screws Make sure the top rear tab locks in place uninet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com XEROX PHASER 3300 TONER CARTRIDGE REMANUFACTURING INST
4. RUCTIONS 38 Press the drum axle bushing in place Set it so the small 39 The chip is held in place by plastic rivets It must be tab is at the end of the groove and make sure it is fully seated replaced for the cartridge to work It can be replaced by first The two small bushings are different Make sure you have the cutting the plastic rivets then drilling two holes and setting two correct bushing for this side self tapping screws in place PRINTING TEST PAGES As these machines are copiers the easiest way is to just make a copy of a Suitable test page REPETITIVE DEFECT CHART Fuser pressure roller 101 3mm Fuser heat roller 88 9mm OPC Drum 75 5mm Supply roller 53 2mm Transfer Roller 47 1mm PCR 37 7mm Developer Roller 39 2mm UniNet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com
5. XEROX PHASER 3300 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS XEROX PHASER 3300 TONER CARTRIDGE uniNnet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com XEROX PHASER 3300 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS REMANUFACTURING THE XEROX PHASER 3300 TONER CARTRIDGE By Mike Josiah and the Technical Staff at UniNet First released in August 2008 the Xerox Phaser 3300 MFP printers are based on a 30ppm 1200dpi engine The first page out is rated at under 8 5 seconds and the monthly duty cycle is up to 25 000 pages Both model printers are print copy scan and fax capable Both machines come standard with 96MB of memory which is upgradeable to 320MB Both also come with duplexing standard These cartridges do not have a drum cover and come new with a piece of heavy paper with foam glued to it taped around the cartridge There are both LY 4 000 pages and HY 8 000 pages cartridges available Each version of cartridge has its own specific chip but the cartridges themselves are identical The chip covers are held in place by plastic rivets To replace the chip the rivets
6. or additional support please contact techsupport uninetimaging com XEROX PHASER 3300 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS 6 On the top edge of the end cap there is a plastic tab Press in on the tab and remove the left end cap T Lift off the roller cover 8 Carefully pry up the side plastic tab to release the waste chamber www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com XEROX PHASER 3300 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS 9 Remove the waste chamber 10 On the supply hopper remove the fill plug and dump out any remaining toner 11 Remove the developer roller drive gear and place a strip of tape across the remaining gears They do not need to be removed and the tape will help keep them in place UniNet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For addi
7. port please contact techsupport uninetimaging com XEROX PHASER 3300 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS 25 Slide the PCR to the non contact side Remove the PCR 26 Remove the two screws and the wiper blade Clean out all 27 Coat the new wiper blade with your preferred lubricant the toner from the hopper It is interesting to note that on new Install the new wiper blade and two screws The tail of the cartridges some toner is in the waste hopper Apparently wiper blade should face up these cartridges are being tested before they are shipped or the drum was lubricated with toner uniNnet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com XEROX PHASER 3300 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS 28 Clean the old conductive grease off the PCR shaft and 29 Install the PCR by sliding the long shaft side through the contact Replace with new Clean the PCR with your preferred non contact side Bring it back to fit into the contact side PCR cleaner WARNING Do not clean the OEM PCR with alcohol as this will remove the conductive coating from the roller If
8. rant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com XEROX PHASER 3300 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS 19 Snap the spring plastic bushing assembly in place Make sure the tail of the spring is set properly 20 Install the drive gear on the developer roller 21 Fill the hopper with Phaser 3300 toner Check for leaks uniNnet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com XEROX PHASER 3300 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS 22 On the waste hopper remove the E ring from the drum 23 Slide the drum axle out from the side opposite the E ring axle 24 Remove the OPC drum UniNet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional sup
9. the PCR is an aftermarket follow the cleaning methods recommended by the manufacturer If the PCR is an OEM we recommend it be cleaned with your standard PCR cleaner 30 Coat the OPC drum with your preferred lubricant and install the drum uninet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com XEROX PHASER 3300 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS 31 Install the drum axle small drum gear side first Make sure that the E ring groove ends up on the small drum gear side whi 33 Install the waste hopper on to the supply chamber 32 Install the E ring Make sure that the tabs lock into place on the side wall uniNnet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com XEROX PHASER 3300 TONER CARTRIDGE REMANUF
10. tional support please contact techsupport uninetimaging com XEROX PHASER 3300 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS 12 On the fill plug side press in on the plastic tab and remove the spring plastic bushing assembly 13 Remove the developer roller 14 Remove the two screws on the doctor blade UniNet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com XEROX PHASER 3300 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS 15 Carefully pry up the doctor blade This blade has a very 16 Clean the doctor blade and foam seals It is too early to say exactly what chemical to use on the blade but so far 99 tight fit work it off carefully Clean out any remaining toner from the hopper isopropyl alcohol seems to work 18 Clean and install the developer roller long shaft side to gear side first 17 Replace the doctor blade and two screws uninet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not war
Download Pdf Manuals
Related Search