Operator & Service Manual Multi-Fruit Juicer
Contents
1. b Cutter installation Align arrows on cutter and juice manifold to seat cutter Make sure cutter is fully seated Tighten set screw DO NOT over tighten FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 17 eP MIG FoodTech Figure 3 Installation of good cutter Figure 3a Bad cutter REPLACE cutter Figure 3b Cutter that can be sharpened Figure 4a Sharpening Cutter Figure 4b Sharpening knife with Whetstone with Whetstone 18 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual PVC Food Tech Maintenance 2 Check orifice tube for damage Refer to Figure 5 Replace tube when a Chunks are missing from top end b Score marks 1 32 or deeper appear along the length of the tube Figure 5 Severely Damaged Orifice Tube 3 Check for loose or missing nuts and bolts a Tighten or replace nuts and bolts as necessary b DO NOT exceed torque ranges specified in Service Manual c ALWAYS use FMC FoodTech recommended spare parts FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual FME FoodTech Periodic Inspection Perform the following steps after every 3 4 months 1 Test all access cover interlock switches Extractor should stop automatically when any access cover is opened Individually open and close the four access covers hopper juice components cart and back If extractor continues to run when any access cover is opene2. T 10 11 12 Pelican brand Peralkalate is recommended see page 12 Read the product label Follow the manufacturer s mixing directions and safety precautions Immerse all components in cleaning solution Use the blunt end of plastic rod provided to displace any fruit material lodged in the bore of the orifice tube Use pointed end of plastic rod to displace any fruit material lodged in cup fingers Scrub components Use a brush towel or sponge DO NOT use abrasive pads such as Scotch Brite steel wool etc Thoroughly rinse with clean water then thoroughly rinse with sanitizer solution Follow the manufacturer s mixing directions and safety precautions For best results soak strainer tube overnight After soaking overnight rinse the strainer tube thoroughly before using Check that all strainer tube holes are clean Clean strainer tube with a hard spray from a hose while moving orifice tube back and forth in strainer tube Rinse thoroughly with sanitizer solution Allow to air dry If possible hose down juicing area and cover If location prohibits using a hose to clean juicing area and cover ensure waste container is in place Wash down the exposed juicing area and cover with a sponge or spray applicator using the recommended cleaning solution Cover may be rinsed in place or removed by lifting it off the hinges Allow to stand for two minutes before rinsing thoroughly with water Re assemble juicing com
3. Da NOT defeat interlack switches Step by Step instructions for replacing all bearings and rod ends 1 Remove all juicing components 2 Lift juicing component cover off its hinges Refer to Figure 1 Remove back cover 1 4 turn lock at top pull cover out by using finger hole to the left of the lock then lift and pull using finger hole of bottom DO NOT loosen any screws Remove drive cover one screw on top and two on the side DO NOT loosen lower two screws 3 Remove upper and lower drive splash plates in juicing area Refer to Figure 16 Use knife to cut away Silicone from plastic splash plates and drive arms If necessary use hand crank adapter on motor sprocket with 1 2 drive ratchet to rotate machine into position to pull off splash plates Refer to Figure 17 and Figure 36 item 12 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual aP MIG FoodTech Upper Drive Splash Plate Drive Access Hole Lower Drive Splash Plate Figure 16 Front View of Juicer Upper Linear Shaft Upper Cup Drive Assembly Upper Rotary Shaft Upper Drive Crank Arm Lower Drive Assembly Lower Drive Crank Arm Lower Rotary Shaft Hand Crank Adapter with Dog Pt Set Screw Figure 17 Back View of Juicer FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 33 FME FoodTech Rebuilding 4 From 3 inch square access hole on side of machine use a 5 16 Alle
4. such as Pine Power or Pine Spic amp Span to remove discoloration from plastic covers Rinse thoroughly with sanitizer solution Clean Tomlinson faucet Daily cleaning is crucial to the performance maintenance and sanitation of the faucet Take apart handle assembly and flush with clean water then sanitize FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual FME FoodTech Maintenance Before performing any maintenance DISCONNECT ELECTRICAL PLUG before cleaning or maintenance Juicer should HOT run when any cover is open Contact with internal moving parts could cause severe injury or death Da NOT defeat interlack switches Extractor requires no lubrication After every juice run 1 Check cutter and knives for sharpness Refer to Figure 3 to determine condition of cutter If dull sharpen with a whetstone provided Refer to Figure 4a to sharpen cutter If cutter is severely damaged or rolled over replace cutter a Cutter removal Disassemble juicing components per Figure 1b page 9 Loosen set screw under front knife make sure screw is backed out far enough to clear cutter Cutter should lift out if not tap the cutter lightly from inside the juice manifold with a 1 1 4 dia rod hammer handle Install red protective cap provided onto cutter After red protective cap is installed remove cutter Handle cutter with care to avoid direct contact with sharp edge
5. Cover Assembly Parts Stainless Steel FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 67 FME FoodTech 68 Item Qty Part Number 1 4 004 401 022 2 2 004 440 004 3 1060 00076 6 1 060 00168 7 1 006 061 003 8 1 060 00141 9 1 060 00106 10 1 006 220 014 11 1 060 00096 03 12 1 006 210 290 13 1 060 00094 14 1 060 00527 15 1 060 00527 01 1 4 004 401 022 2 2 004 440 004 3 1060 00076 6 1 060 00169 8 1 060 00141 9 1 060 00196 10 1 006 220 004 12 1 006 210 290 13 1 060 00198 14 1 060 00525 15 1 060 00525 01 16 1 Electrical Parts 060 00034 D Description 110 Volt Parts Screw Mach Truss 10 24 x 3 8 SS Phillips Screw Tap F 6 32 x 3 8 SS Phillips Not Shown Switch Plate Electrical Box Assembly 115 V Wire Nut 74 B Not Shown Switch Bracket Motor Assembly Terminal 410 Ring End For 10 12 Ga Wire 20 Ga x 5 Lg White Not Shown Prox Switch NC With Gray Leads Supply Wire Cable Back Cover Cable Cart Door 220 Volt Parts Screw Mach Truss 10 24 x 3 8 SS Phillips Screw Tap F 46 32 x 3 8 SS Phillips Switch Plate Electrical Box Assembly 220v 50 Hz Switch Bracket Motor Assembly 220 V 50 Hz Terminal 10 Ring End For 14 16 Ga Prox Switch NC With Gray Leads Supply Wire 220 V 50 Hz Cable Back Cover Cable Cart Door Plug Depends On Machine Destination Not Shown Machines equipped with high
6. equipment parts DO NOT use abrasive pads such as Scotch Brite steel wool etc The recommended cleaner is Pelican brand Peralkalate Peralkalate is a low foaming alkaline equipment cleaner It is safe on aluminum 100 water soluble and free rinsing Peralkalate has been especially formulated for cleaning food processing equipment and is USDA accepted Follow instructions on cleaner label for dilution 1 Turn off Extractor with Juicing Component cups separated 2 DISCONNECT ELECTRICAL PLUG DISCONNECT ELECTRICAL PLUG before cleaning or maintenance Juicer should NOT run when any cover is open Contact with internal moving parts could cause severe injury or death Da MOT defeat interlock switches 3 Pull Extractor to clean up area if one is available Juicer weights over 250 lbs Move juicer an LEVEL surface only Never an inclined surfaces Move only by PULLING on handle 4 Brush all loose peel into waste container or bag 5 Empty and rinse waste container 12 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual PVC Food Tech Cleaning Instructions 6 Remove juicing components a Cups should be separated Extractor should have been turned off with cups in the separated position b Grasp upper cup and pull out pin just above it Place upper cup in waste container c Remove splatter shield by sliding upwards off mounting screws d Remove lower cup
7. 004 265 017 060 00080 060 00073 060 00072 Description Hopper Modification Cover Main Cover Door Spacer Switch Cover Cover Switch Cover Drive S S Cover Back Shield Clear Bracket R H Bracket L H Cover Hopper Cover Juice Assembly S S Latch Spring Toolhead Sign Warning Cover Switches Assembly Instructions Cleaning Instructions Screw Mach Truss Nylok 10 24 x 3 8 Phillips Nut S L 10 24 S S Sign Warning Moving Juicer Patent Plate Name Plate Rivet Pop 1 8 Dia x 1 8 Grip Retainer Back Cover Cable Tie Holder Key Ring amp Key Not Shown Label On Off Warning Label Shear Hopper Pin Reservoir Holder Bumper Stem Type 5 8 x 15 16 Covers Items 4 12 amp 13 Include the Following Parts Latch Spring Toolhead Southco 57 T 10 Items 4 12 amp 13 Rivet Blind 1 8 Dia x 3 8 Alum Items 12 amp 13 Rivet Pop 1 8 Dia x 1 8 Grip Item 4 only Covers Items 4 12 amp 13 Include the Following Hinges Hinge Door Stand Hinge Quantity of 1 on Item 4 Hinge Cover Hopper Hinge Quantity of 1 on Item 12 Hinge Front Cover Female Hinges Quantity of 2 on Item 13 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual aP MIG FoodTech PARTIAL VIEW B B BACK COVER AND STAND COVER PARTIAL VIEW B B BACK COVER eos 183 INSIDE DOOR INSIDE DOOR les FRONT VIEW FRONT VIEW COVERS REMOVED Figure 48
8. 18 2 Rivet Blind 1 8 Dia x 1 4 Alum item 14 only Covers Items 3 14 amp 17 Include the Following Hinges 1060 00073 Hinge Cover Hopper Quantity of 1 on Item 17 above 2 0060 00072 Hinge Front Cover Female Quantity of 2 on Item 3 above 1060 00080 Hinge Door Stand Quantity of 1 on Item 14 above Machines equipped with high level switches FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual eP MIG FoodTech Figure 45 Cover Assembly Parts ABS FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 63 FME FoodTech Splash Shield Assembly Parts 060 01054 B Item Qty Part Number OOI POND 1 1 1 4 4 060 01025 060 01024 060 01024 01 004 401 022 004 156 041 Description Shield Clear Bracket Clear Shield RH Bracket Clear Shield LH Screw Mach Truss Nylok Phil 10 24 x 3 8 Nut Hex S L 10 24 SS 64 LEFT SIDE MEW FRONT VIEW Figure 46 Splash Shield Assembly Parts FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual PVC Food Tech tem Qty c OO NOU RO Decals Warning Labels Bumpers Part Number 060 00120 060 00121 009 450 040 009 450 041 060 00122 060 00083 060 00082 009 450 034 01 009 450 031 009 450 033 009 450 035 060 00193 01 060 00193 03 Description Decal Warning Sign Decals on item 3 14 amp 17 Interior Decal Warning Sign 1 on item 3 1 on Hopper Side amp 1 Bac
9. Arm Upper Drive this part includes items 1a amp 1b Fitting Grease 1 4 28 45 Bearing 1 x 1 Pin Faspin 3 8 x 1 5 8 Cup Upper Screw Cap Hex 5 8 11 x 2 1 2 Lock Rod End Rod End Assembly Upper Cup Drive Details See Page 57 Screw Upper Cup Crank LH Washer Plain Narrow 5 8 Crank Upper Cup Drive FAR SIDE TYP Figure 40 Upper Drive Arm Assembly Parts FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual PVC Food Tech Rod End Assembly Upper Cup Drive Parts 060 00114 B Item Qty Part Number Description 1 1 005 098 729 Rod End RH 5 8 2 1 004 116 046 Nut Jam Hex 5 8 18 S S 3 1060 00060 Linkage Cup Drive 4 1 004 116 047 Nut Jam Hex LH 5 8 18 S S 5 1 005 098 730 Rod End LH 5 8 VA AAS Figure 41 Rod End Assembly Upper Cup Drive FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 57 FME FoodTech Orifice Drive Arm Assembly Parts 060 00115 C Item Qty Part Number Description 1 1 060 00058 Orifice Crank Arm 2 2 004 816 100 Washer Plain Narrow 1 2 S S 3 1 004 352 572 Screw Cap Hex LH 4 1 060 00113 Rod End Assembly Orifice Drive Details See page 59 5 1 004 352 571 Screw Cap Hex 1 2 13 x 1 1 2 6 1060 00011 Arm Orifice Tube Drive this part includes items 6a amp 6b 6a 1 007 120 205 Fitting Grease 1 4 28 45 6b 2 005 098 731 Bearing 1 x 1 7 2 060 00068 Bearing Fruit Lift Q Figure 42 Orifice
10. Bearings and Thrust Washers Installation Pilot Installation Washer Bearing Installation Rod FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 43 eP MIG FoodTech Rebuilding 44 16 Before installing chain align timing marks as shown 17 Refer to Figure 32 This is critical to operation of the machine Adjust chain as shown in Maintenance section To check to see if upper cup crank rod end link needs to be adjusted install juice manifold upper and lower cup Refer to Figure 33 Using hand crank adapter gently rotate until upper cup drive is in the full down position DO NOT force it if it appears to be binding readjust rod end link Figure 34 If it rotates freely past bottom position check for too much clearance In the full down position remove pull pin from upper cup Cup should not drop down if it does readjust rod end link Cups should just meet no clearance no bind Rotation Align marks Figure 32 Alignment of Timing Marks FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual aP MIG FoodTech Figure 34 Adjusting Rod Link Ends FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 45 eP MIG FoodTech Rebuilding 18 Remove juicing components and install upper and lower drive splash plates Refer to Figure 35a and 35b Note that chamfer on top front edge of lower splash plate goes up and out Put thin part to the
11. level switches all others have two prox switches on juicing cover FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual FME FoodTech TO BACK COVER G O FEED WIRE UNDER MOTOR JUNCTION BOX AND UP TO ELECTRICAL BOX mmm _ Oe e L see lag i TO CART DOOR Figure 49 Electrical Parts FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 69 FME FoodTech Electrical Box Assembly Parts 115 Volt 060 00168 C 70 Item CO NO OF WN ND ND ND ND ND ND ND k Ad ad mk mk mk mk mk S CE O OAR OO ND OO WON OU BW N O Qty N A ND ND ND lt a AN NM AA ND OWA ND A ND ND NN mk Part Number 060 0016 006 040 062 006 190 054 007 146 010 007 486 118 006 060 044 060 00538 006 221 066 006 060 074 007 146 009 060 00074 004 397 137 060 00075 004 397 077 060 00096 01 060 00537 004 352 383 004 816 080 060 00165 060 00166 006 060 077 004 816 052 007 143 396 006 090 245 004 430 002 007 143 397 Description Electrical Box Sprecher Schuh M S Under volt Release Sprecher Schuh KT3 25 UA 110 Manual Starter Sprecher Schuh KTA3 25 16A Nut Tru Seal 1 2 NPT Sealing Ring Hubbell 20509001 Cord Conn T amp B 2682 1 2 NPT 90 Switch Diaphragm Terminal Block Curtis 1505 W Cord Conn T amp B 2671 3 8 NPT Straight Nut Tru Seal 3 8 NPT Panel Screw Mach Round 10 24 x 3 8 S S Box Mounting Pl
12. top and flat backside against the wall Also note that groove in upper drive splash plate goes down and in Seal with R T V Silicone allow to dry before running machine ne Figure 35a Applying Silicone to Upper Splash Plate Figure 35b Applying Silicone to Lower Splash Plate 46 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual PVC Food Tech Elect Box Motor Storter BLUE Releose Coil Under Voltage CROUND GREEN YELLOW voltage Termina Tronsformer dr Block Mounted under Terminal Block S 220 Volt I 16 Amp Electrical Diagram A PLUG BROWN Machines built before 1997 Machines built in 1997 and later FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 47 FME FoodTech 48 Rebuild Tooling Kit amp Spare Parts Kits a 3 CON OOF WN ND oa mk mk mk mk mk mk mk mk O O O ON OU POND O Part Number 060 00180 B 060 00181 B 060 00182 B 060 00183 B 060 00184 B 060 00185 B 060 00186 B 060 00187 B 060 00188 B 060 00189 B 060 00190 B 060 00191 B 004 350 648 004 350 571 004 110 063 004 815 100 00 4815 080 004 350 407 004 410 046 009 998 004 060 00202 Description Tool Bearing Installation Pilot Tool Bearing Installation Washer Tool Bearing Puller Tool Bearing Removal Slug 1 Tool Bearing Removal Slug 1 1 4 Tool Bearing Removal Driver Tool Bearing Installation Rod Tool
13. 07 143 397 Description Electrical Box Sprecher Schuh M S Under volt Release Sprecher Schuh KT3 25 UA 110 Manual Starter Sprecher Schuh KtTA3 25 10A Nut Tru Seal 1 2 NPT Sealing Ring Hubbell 20509001 Cord Conn T amp B 2682 1 2 NPT 90 Frame Diaphragm Terminal Block Phoenix G5 6 Cord Connector T amp B 2671 3 8 NPT Straight Nut Tru Seal 3 8 NPT Panel Screw Mach Round 10 24 x 3 8 S S Box Mounting Plate Screw Mach Round 8 32 x 1 2 S S Jumper Wire 20 Ga x 5 Lg Jumper Wire 12 Ga x 10 Lg Screw Cap Hex 3 8 16 x 1 2 S S Washer Plain Narrow 3 8 S S Transformer Signal 4DP241 4 120 Terminal Fully Insul Panduit ZDNF18 206FIB C Stand Off Terminal Strip Screw Mach Round 48 32 x 1 1 4 Lg S S Screw Mach Round 48 32 x 1 4 Lg S S Washer Plain 10 S S Spacer Din Rail Motor Starter Mounting Cord Conn Straight T amp B 42673 1 2 NPT x 1 2 Dia Cord Marker Pins Phoenix BNB Set 10 Thru 15 Mounting Pad Terminal Block Screw Mach Round Head 44 40 x 3 4 Lg S S Jumper Wire 20 Ga x 10 Lg Wire Markers Strain Relief Fitting Plug Snap In Nylon Diaphragm Switch Screw 4 x 3 8 Lg Type B S S Nut Locking PG11 aP MIG FoodTech tee a 15 Mounted under Terminal Block oio mo ay TONO Elect Box Motor Starter Terminal KE Block MM Bl a XT i P 3 3 13 Release Coll L Une
14. 1 005 576 246 060 00115 060 00063 004 541 111 Description Chain 60 x 60 3 4 Lg 81 Links Link Connecting For 60 Electrical Assembly Details See Pages 68 69 Sprocket 60B14 Set Screw for motor Screw Cap Hex 3 8 16 x 1 3 4 Washer Lock Reg 3 8 S S Washer Plain Narrow 3 8 S S Frame amp Stand Assembly Details See Pages 60 61 Shaft Linear Upper Upper Drive Arm Assembly Details See Page 56 U C Drive Arm Sprocket Upper Cup Screw Cap Socket 3 8 16 x 2 Washer Thrust 1 1 4 Shaft Rotary Drive Upper Key Sa 1 4 x 1 1 2 S S Sprocket Drive Orifice Washer Thrust 1 Key Sa 1 4 x 1 S S Screw Cap Socket 3 8 16 x 3 4 Shaft Rotary Drive Lower Key Sa 1 4 x 3 4 S S Key Sq 1 4 x 1 1 4 S S Orifice Drive Arm Assembly Details See Page 58 Shaft Linear Orifice Drive Screw Set Socket 5 16 18 x 3 4 S S for Motor Sprocket FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual aP MIG FoodTech T Ss er EET MT N N AR A N N S IN S S 55 Figure 39 Drive Parts FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual FME FoodTech 56 Upper Drive Arm Assembly Parts 060 00116 C Item SONDA E ON AA O Qty Part Number 060 00030 007 120 205 005 098 731 004 226 039 060 00027 004 352 661 060 00057 060 00114 060 00078 004 816 120 060 00009 Description
15. 13 26 1 060 00148 Decal Install Trash Bag On Hooks Before Juicing 27 1 0060 00120 Decal Warning Sign 28 6 060 00125 Retainer Back Cover 29 2 004 816 052 Washer Plain 10 S S 30 1 009 210 013 Float Cyl 1 1 2 x 2 5 8 Polyp oll 1 060 00137 Frame Reservoir Float Pivot 32 1 060 00140 Magnet Holder Reservoir 33 1 006 210 291 Magnet Proximity 34 1 009 080 050 Bumper Stem Type 5 8 x 15 16 35 2 006 200 267 Switch Safety Schmersal 36 2 007 143 395 Strain Relief Fitting 37 4 004 392 175 Screw Mach Pan Head 8 32 x 3 4 S S 38 1 060 02059 Button Threaded 39 1 004 401 024 Screw Mach Truss 10 24 x 1 2 S S Phillips 40 2 009 654 003 Holder Wire 41 3 006 270 141 Tie Wire 42 1 004 385 012 Screw Flat Head 46 32 x 3 4 S S 44 4 004 392 174 Screw Mach Pan Head 48 32 x 1 2 S S 45 2 060 00524 Strip Backing 46 1 060 00121 Decal Warning Sign 47 2 006 200 489 Funnel Adapter with Long Key 48 1 007 160 029 Grommet 7 16 Dia Hole x 15 16 OD Use on S S Covers Only 49 1 009 097 002 Cable Tie Holder 50 2 004 136 021 Nut Hex Flanged Serrated 8 32 S S 51 2 004 385 028 Screw Flat Head 46 32 x 3 8 S S 52 2 004 356 013 Screw Socket Head Cap Button Head 10 24 x 1 S S 53 4 004 806 030 Washer Lock 10 S S Covers Items 3 14 17 amp 18 Include the Following Parts 4 009 425 019 Latch Spring Toolhead Southco 57 T 10 items 3 14 17 amp 18 6 Rivet Blind 1 8 Dia x 3 8 Alum Items 3 17 amp
16. Bearing Removal Rod Tool Washer Rod End 1 2 Tool Washer Rod End 5 8 Tool Rod End Adjust Bar Tool Adapter Hand Crank Screw Cap Hex 5 8 11 x 1 1 2 C G Screw Cap Hex 1 2 13 x 1 1 2 Full Thread C G Nut Hex 1 2 13 Grade 8 Steel Washer Plain Narrow 1 2 C G Washer Plain Narrow 3 8 C G Screw Cap Hex 3 8 16 x 2 C G Screw Set Square Head Dog Pt 3 8 16 x 3 4 Bit Spanner Insert 8 1 4 Hex Not Pictured Kit Tool CJ amp MFJ Includes above Items 1 20 Other Multi Fruit Juicer Kits 060 00201 060 00215 060 00200 Kit Bearing Overhaul Kit Complete Overhaul Kit Spare Paris Cleaning Components amp Other Paris 060 00084 009 080 326 060 00131 009 710 031 003 460 053 003 460 057 003 015 905 Rod Orifice Clean Out Brush 1 1 16 x 8 Peralkalate Cleaner 750 M Stone Sharpening Lubricant W Teflon 3 Oz Tube Lubricant W Teflon 14 Oz Can Silicone White 3 Oz Tube FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual PVC Food Tech O o 2 D er s 6 p 7 mmm 8 mmm OQ 10 00 3 Joe 14 05 15 16 OO _ 7 00009 ig oo 19 20 Figure 36 Rebuild Kit FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 49 FME FoodTech 50 Item c OO NNOOOU POND ND ND ND AA AA HH AH ak ND AAND AA k k MM N
17. D AA k LO AN N k ND Gty Part Number 060 00103 004 352 410 004 816 080 060 00056 060 00051 060 00043 060 00043 01 060 00118 060 01001 060 00038 060 00028 060 00004 060 00098 060 00109 060 00225 004 406 003 060 00108 007 486 119 004 352 398 060 00022 060 01059 060 00068 060 00086 060 00208 060 00230 060 00055 060 00008 1 060 00077 009 092 018 060 00121 060 00192 004 100 018 004 806 070 060 00088 060 01069 060 01066 060 01067 Juicing Parts 060 00099 F Description Drive Assembly Details See Pages 54 55 Screw Cap Hex 3 8 16 x 2 1 4 S S Washer Plain Narrow 3 8 S S U C Drive Cover Plate Spanner Screw Hopper Assembly ABS Hopper Assembly SS Cover Assembly ABS Details See Pages 62 63 Cover Assembly Stainless Steel Details See Pages 66 67 Lift Fruit FDA Material Guide Fruit FDA Grade Cup Lower Spanner Nut Stud Cup Lower Cutter With Screw Screw Mach Round 4 40 x 3 16 S S Manifold Juice O Ring Nozzle 1 x 1 1 8 x 1 16 Screw Cap Hex 3 8 16 x 1 1 4 S S Nozzle Straight Plastic Nozzle SS 90 Bend Jamba Bearing Fruit Lift Tube Strainer 033 Tube Strainer 040 Tube Strainer 055 Plate Orifice Drive FDA Grade Tube Orifice Tool Wrench Not Shown Cap Cover for Cutter Not Shown Warning Label Shear Hopper Pin Manifold Locator Nut Acorn 3 8 16 SS Washer Lock 3 8 SS Parts for Small Fruit Res
18. Drive Arm Assembly Parts 58 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual PVC Food Tech Rod End Assembly Orifice Drive Parts 060 00113 B Item Qty Part Number Description 1 1 005 098 727 Rod End Male RH 2 1 004 116 037 Nut Jam Hex 1 2 20 3 1060 00059 Linkage Orifice Drive 4 1 004 116 038 Nut Jam Hex LH 1 2 20 5 1 005 098 728 Rod End Male LH 1 2 VA A Figure 43 Rod End Assembly Orifice Drive Parts FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 59 FME FoodTech Frame amp Stand Assembly Parts 060 00117 D Item Qty Part Number 1 1 060 00101 1a 2 007 120 203 1b 2 005 098 731 1c 2 005 098 732 2 1 O060 00048 3 2 009 080 526 5 5 004 352 392 6 4 004 111 022 7 4 004 461 025 12 2 009 080 527 13 1060 00079 14 16 004 111 040 15 18 004 816 070 16 22 004 352 315 60 Description Frame The frame contains items 1a 1b amp 1c Fitting Grease 1 4 28 Straight Not Shown Bearing 1 x 1 Not Shown Bearing 1 1 4 x 1 1 4 Not Shown Stand Caster Swivel 4 Screw Cap Hex 3 8 16 x 7 8 Nut Hex 4410 24 S S Hook Caster Rigid 4 Locator Waste Bin Nut Hex 5 16 18 S S Washer Plain Narrow 5 16 S S Screw Cap Hex 5 16 18 x 3 4 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual PVC Food Tech FRONT HOOKS POINT TO FRONT BACK HOOKS POINT TO BACK DS Q
19. OUD AND FAN 4 TO INSTALL IT 14 TOP amp BOTTOM FILL KEYWAY WITH GREASE Figure 52 Motor Assembly Parts FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 75 76 Item Part Number 060 00084 B 009 080 328 009 080 327 060 00131 009 092 019 009 425 020 SA ERON Miscellaneous Parts Description Rod Orifice Clean Out CJ amp MFJ Brush 1 Dia Brush Dish Type Peralkalate Cleaner 750 M Decanter 1 Gal Translucent Key ToolHead berich FenaLkak han par z FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual
20. ance Juicer should HOT run when any cover is open N Contact with internal moving parts could cause severe injury or death Da NOT defeat interlack switches Juicer weights over 250 Ihs Move juicer an LEVEL surface only Mever an inclined surfaces Move only by PULLING on handle Safety Instructions Carefully review the following safety instructions Make them a habit when using the FMC FoodTech Juice Extractor 1 Q1 A G N o If extractor continues to run when any access cover is open interlock switch is defective Turn Juicer off immediately Call for service Prevent unauthorized access to Extractor by locking all covers with supplied key Prevent unauthorized operation of Extractor by placing electrical plug inside cart door NEVER attempt to make any safety device inoperative NEVER operate or perform maintenance or repair work on Extractor when taking any kind of drug or sedative when under the influence of alcohol or when fatigued ALWAYS check adjustment of all nuts bolts and screws after installation repair or periodic maintenance FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual FME FoodTech Technical Specifications Fruit size 2 1 2 to 3 3 4 diameter 6 5 cm to 9 5 cm Oranges NEN FL Rag CeCe CRE CERT CECE CEE RR 125 to 50 count Oranges EE CA RA AT OE Cre OE N 138 to 48 count Grapefruit FL TMA e 56 to 48 count Hopper
21. ate Screw Mach Round 8 32 x 1 2 S S Jumper Wire 12 Ga x 2 1 4 Lg Frame Diaphragm Screw Cap Hex 3 8 16 x 1 2 S S Washer Plain Narrow 3 8 S S Spacer Din Rail Motor Starter Mounting Cord Conn Straight T amp B 2673 1 2 NPT x 1 2 Dia Cord Washer Plain 10 SS Strain Relief Fitting Plug Snap In Nylon Screw 4 x 3 8 Lg Type B S S Nut Locking PG11 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual eE MIG FoodTech VOO ER 337 Ms 3 4 9 DE Figure 50 Electrical Box Assembly Parts 115 Volt FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 71 FME FoodTech Electrical Box Assembly Parts 220 Volt 060 00169 C Item CO NO OF WD GO C C0 C0 OO OO WEN NN ND NNN DDD A mk mk mk mk mk mk mk mk ak O N OO fF WD O 0 ON OU HO ND AA OO ON OU E WN O Qty k N ND PO OD amp N N HA a O AN N N AA ad ND N a A R Co AR D nm N Part Number 060 0016 006 040 062 006 190 063 007 146 010 007 486 118 006 060 044 060 00537 006 221 079 006 060 074 007 146 009 060 00074 004 397 137 060 00075 004 397 077 060 00096 03 060 00096 02 004 352 383 004 816 080 006 240 027 006 221 081 060 00170 004 397 104 004 397 072 004 816 052 060 00165 060 00166 006 060 077 009 455 004 060 00194 004 440 001 060 00096 07 007 143 396 006 090 245 060 00538 004 430 002 0
22. by removing spanner nuts on either side of lower cup A spanner wrench is provided to loosen tighten spanner nuts Place lower cup in waste container e Install red protective cap on cutter Red protective cap is provided f Grasp juice manifold and orifice tube firmly Remove entire juicing components assembly g Grasp orifice tube and pull out of strainer tube h Remove strainer tube from inside juice manifold by turning tube counter clockwise and sliding out A Spanner wrench is provided to loosen tighten Strainer tube Place juicing components into waste container FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual FME FoodTech STRIP DOWN DRESS UP Stop machine wi h Pin Hold onto upper cup before pulling pin Clear Splatter Shield Spanner screw JP Tool Tighten spanner screw amp nuts securely with tool Tighten strainer tube securely with tool Tighten Upper Cup CAUTION Do not place hands or fingers between cups Spanner Nuts Loosen Tighten B Lower Cup CAUTION Knives amp cutter are very sharp Juice Manifold O Ring Nozzle Strainer Tube Loosen CAUTION Hold onto orifice tube when removing or assembling Orifice Tube Groove in slot Figure 2 Juicing Components FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual PVC Food Tech Prepare cleaning solution
23. c Multi Fruit Juicer Service amp Operational Manual 2 FME FoodTech Troubleshooting Extractor will not start b Check continuity thru all switches Refer to Figure 15b amp 15c c Check continuity across each switch Refer to Figure 15b amp 15c Using a meter check each switch individually Check by opening and closing each cover related to the switch you are checking Replace any defective switches d Some linkage adjustment may be required on juice reservoir float switch e Machines built in 1997 and later have two Schmersal Switches Check alignment of key and switch Adjust if necessary 5 Loose wire connection Check all spade and screw terminals With wires still connected remove cover to motor starter and check for loose wires on D1 and D2 6 Defective under voltage coil Check continuity from terminals D1 to D2 Using a meter check for continuity from terminal D1 to D2 If no continuity is detected replace under voltage coil 7 Defective motor starter Check continuity from terminal 1 to 6 Remove cover on motor starter by grasping both sides and pulling straight out Remove under voltage coil by lifting and pulling out Push ON button Button should stay in down position Using a meter check for continuity from terminal 1 to 6 If no continuity is detected or ON button does not stay down replace motor starter 8 Defective motor If ON button on starter stayed in when trying to star
24. capacity EE Cree TT eR IL IET 40 Ib 1 carton 18 Kg Reservoir capacity EE ennen Ee ee ees 3 1 2 gal 1 carton 13 2 liters Waste container capacity rer 40 Ib of peel 2 cartons 18 kg Speed ee AE enne CCC rer oT 20 fruit minute 20 to 60 gallons hour 75 to 225 liters hour Electrical Specifications 115V 60HZ Single Phase 20 AMP Service 12 GA wire up to 100 ft from main breaker panel or 10 GA wire up to 200 ft from main breaker panel 220 VAC 50HZ Single Phase 16 AMP Service Shipping Specifications Machine With Stand Height 67 170 cm Width 27 69 cm Depth 32 81 cm Weight 535 Ibs 243 kg Patents U S Patents 4905586 and 4922814 amp Patents Pending 6 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual PVC Food Tech General Information The FMC FoodTech Juice Extractor is designed to provide years of dependable service It uses a unique patented design to extract every available amount of juice from the fruit with the least amount of peel oil The peel is completely separated from the juice and juice sacs before being compressed and strained The machine will juice all types of citrus oranges grapefruit lemons limes tangerines etc without changing or adjusting parts In fact different varieties and sizes of fruit can be juiced to create various fruit juice blends Clean up is simple requiring disassembly of only five parts All waste mate
25. d the interlock switch is defective Stop the extractor and replace immediately See Trouble Shooting Section 2 Check all fasteners for tightness Check especially on the Sprockets Crank Arms Fruit Lift and Hopper 3 Check chain for tightness Refer to Figure 6 Chain should have 1 4 inch maximum slack on top side To adjust See Figure 7 loosen the four bolts holding the gearbox base to frame move motor gearbox to the correct adjustment If necessary use a small board to pry between frame and motor 4 Check chain and sprockets for rust If rust appears coat chain and sprockets with a small amount of grease 20 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual aP MIG FoodTech Figure 7 Loosening Bolts on Base of Motor and Prying Motor FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 21 FME FoodTech Periodic Inspection 5 Check oil level in gearbox Refer To Figure 8 If Extractor has been laid on its side for any reason i e during shipping or if there is any evidence of oil leak check gearbox for proper oil level Remove back cover Oil level plug is located on the left side of gearbox Filler plug is located on the top of the gearbox Use S A E 40W oil only 6 Check hopper bump button Refer to Figure 9b Replace bump button if it has worn to less than 1 8 high To locate hopper bump button remove hopper a Hopper removal Fr
26. eE MIG FoodTech _Multi Fruit Juicer MIC FoodTech Operator amp Service Manual Multi Fruit Juicer April 2007 eP MIG FoodTech Operator amp Service Manual Multi Fruit Juicer Multi Fruit Juicer MIC FoodTech Copyright FMC Technologies Inc 2007 FMC FoodTech 400 Fairway Avenue Lakeland FL 33801 863 683 5411 Manual No 060 00203 April 2007 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual PVC Food Tech Safety Il OF dont life gt EE EEN 4 Safety Instructions esse eee eee eee eee 5 General Information see eee eee ee ee ee ee ee ee ee ee ee ee ee ee 7 Operating InstructionS esse EE EER ossos so HH 10 Cleaning Instructions nennen enne ER ER EE Ee EER EER ER ER Ee Ee ERA ERA EER EER ER 12 Maintenant EE NE UEM DUE 17 ed ee EER OE EE ON 20 Troubleshooting sese 26 atre 32 a s 48 Juicing Components Listing nnen ER Ee EA ERA ER Ee Re Re ee ee 50 Hopper Parts Listings ee ese ese ese ee EER Ee nennen 52 Drive Pans EC eenen 54 Upper Drive Parts Listing ennn EE eenenennnnennveneeennnnnnnnnennneennnen 56 Upper Rod End Parts Listing nnen eenn enneeereeeneennnnnnnnenrenenrenn 57 Office Drive Parts Listing sesse se eee 58 Office Rod End Parts Listing 59 Frame amp Stand Parts Listing ssssss00000nnnnnnnnnnnnvnnnnnnnnnnnnnnnnnennnnnenene 60 Cover ABS Parts Listing HH 62 Splash Shield Parts Listing 64 Decals Warning Label Listing nnen EE EER RE EE RE EER EE EE
27. ee ee ee ee Rees 65 Cover SS Parts Listing sees EE ER HH 66 Electrical Parts bilinga EE 68 Electrical Box 115V Parts Listing nnen eneen seia 70 Electrical Box 220V Parts Listing 72 Motor Assembly Parts Listing mmm Im 74 Miscellaneous Parts eren 76 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual FME FoodTech Important Safety Information You can help prevent personal injury and or property damage Please read this manual carefully before operating the FMC FoodTech Extractor DO NOT attempt any operation until you understand exactly how the machine functions If uncertainty remains after studying this manual please contact FMC Technologies Inc FMC FoodTech 400 Fairway Avenue Lakeland FL 33801 863 683 5411 or The local FMC FoodTech service representative in your country We re here to help With proper handling the FMC FoodTech Juice Extractor will provide safe efficient and convenient service for years to come 4 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual PVC Food Tech Safety Labels The safety labels shown below appear on the Juice Extractor They provide essential instructions on how to avoid possible hazards Please for your safety FOLLOW THOSE INSTRUCTIONS AT ALL TIMES Should the Juicer safety labels become damaged or unreadable contact FMC FoodTech for replacement labels DISCONNECT ELECTRICAL PLUG before cleaning or mainten
28. from drive and crank arms Note location and numbers of washers and spacers NOTE Screws and rod ends on both crank arms are left hand threads 10 Disassemble rod ends from links Reassemble with new rod ends Refer to Figures 22 and 23 using rod end adjustment bar with the appropriate rod and tooling washer Remember one end is a left handed thread Wrenches required 3 4 7 8 and 15 16 Figure 21 Removal of Linear Shafts with Puller 36 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual eE MIG FoodTech Rod End Adjustment Bar 5 8 Tooling Washer Figure 22 Assembly of 5 8 Rod Ends 1 2 Tooling Washer Figure 23 Assembly of 1 2 Rod Ends FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 37 eP MIG FoodTech Rebuilding 11 Remove sleeve bearings from upper and lower drive arms Refer to Figures 24 and 25 Bearings can be pulled out using puller 1 removal slug and short threaded removal rod or can be driven or pressed out using driver New bearings can be installed by compression Figure 26 by using installation pilot installation washer and long threaded installation rod or just use installation pilot and press bearings into place Light coat of Teflon grease can be used on O D of bearings Bearing Removal Slug 1 Inside Bearing Removal Puller Bearing Removal Rod 4 2 13 Nut Bearing Removal Driver Figure 24 Removing Bearing
29. i i i i i i i 1 E 9 i rm M ER ER EA ER RE BE ER ER ER ER EE RR EE en A7 a A G Figure 44 Frame amp Stand Assembly Parts FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 61 FME FoodTech Cover Assembly Parts ABS 060 00118 F Item Qty Part Number Description 62 1 1 060 00044 Cover Drive UL 4R597016 2 1 060 01054 Shield Splatter Assembly 90 Bend Details See Page 64 060 00111 Shield Splatter Curved Obsolete Old Style 3 1 060 00045 Cover Juice Components UL R597016 4 1 0060 00123 Clip Latch 5 24 004 401 022 Screw Mach Truss Nylok 10 24 x 3 8 Phillips 6 2 060 00110 Plug Hopper UL R597016 7 2 060 00071 Hinge Cover Front Male 8 4 004 816 060 Washer Plain Narrow 1 4 S S 9 1 060 00025 Reservoir Lid FDA Material 10 1 060 00107 Stirrer Reservoir 11 1 060 00036 Reservoir Juice FDA Material 12 1 060 00162 Faucet 13 14 004 401 026 Screw Mach Truss 10 24 x 5 8 Phillips 14 1 060 00047 Cover Door Stand UL R597016 15 1 0060 00035 Cover Main Stand UL R597016 16 2 0060 00097 Pin Reservoir Holder 17 1 060 00032 Cover Hopper UL R597016 18 1 0060 00033 Cover Back UL R597016 19 1 0060 00046 Cover Switch UL R597016 20 1060 00090 Spacer Switch Cover 21 1 015 03939 Name Plate 22 8 004 265 016 Rivet Pop 1 8 Dia x 1 4 Grip 23 1 015 03937 Patent Plate 24 1 009 092 022 Container 19 1 2 x 23 1 2 x
30. k of Hopper Decal Component Assembly Instructions Decal on item 3 Decal Cleaning Instructions Decal on item 18 Decal Warning Sign Moving Juicer Decal on item 18 Label On Off UL NNP 101 Label on item19 Decal Warning Sign Do Not Open Label on item 17 Exterior Decal Base Fruit Recessed Decals on items 1 14 amp 2 15 Decal Logo Fresh n Squeeze Decals on items 1 1 1 3 amp 2 17 Decal Roof Fruit Decals on items 3 17 amp 18 Decal Stripe Red Decals on Items 3 2 17 amp 1 Bumper Urethane x 26 Lg Bumpers on item 15 Bumper Front Urethane x 7 1 2 Lg Bumpers on item 14 The referenced item numbers in the description above within parenthesis refer to the item numbers on pages 62 63 10 LEFT SIDE TOP RIGHT SIDE TOP FI TN pe e Figure 47 Decals Warning Labels Bumpers FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 65 FME FoodTech 66 Cover Assembly Parts Stainless Steel 060 01001 F Item Qty Part Number N k mk mk mk mk mk mk mk mk mk mk mk mk no A G 060 01036 060 01038 060 01055 060 01044 060 01042 060 01041 060 01040 060 01025 060 01024 060 01024 01 060 01060 060 01061 009 425 019 060 00120 009 450 040 009 450 041 004 401 022 004 156 041 060 00122 015 03937 015 03944 004 265 017 060 00125 009 097 002 060 05058 060 00083 060 00121 060 00097 009 080 050 009 425 019
31. m a under Extractor will not start for removing covers Dial next to OFF button should be set at 14 Extractor stalls trying to squeeze a fruit 1 Fruit has part of stem on it Turn off Extractor Remove fruit from Extractor and restart Peel is too thick Turn off Extractor Remove fruit from Extractor and restart Cutter is damaged Sharpen or replace cutter as specified on under maintenance Install red protective cap onto cutter After red protective cap is installed remove cutter Handle cutter with care to avoid direct contact with sharp edge Extractor runs with covers open or off 1 Defective interlock switch Replace immediately See page 26 item a under Extractor will not start for removing covers Extractor emits a squealing sound during operation 1 Lubricate grease fittings on machine If noise continues rod end or bearing is defective see Rebuilding section to replace bearings Scraping noise coming from hopper area 1 Fruit lift mechanism is dragging on hopper See page 24 item 7 under periodic inspection FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 31 FME FoodTech 32 Rebuilding It is best to replace all bearings at the same time DISCONNECT ELECTRICAL PLUG before cleaning or maintenance Juicer should HOT run when any cover is open Contact with internal moving parts could cause severe injury or death
32. n wrench to loosen socket head cap screw on crank arm for upper cup drive Use hand crank adapter to rotate as necessary Use a 3 16 Allen wrench to loosen set screw on keyway Back screws out at least 1 4 to clear flats on shafts Refer to Figure 18 From the back repeat above steps on crank arm for lower drive Refer to Figure 19 5 Rotate drive so upper cup drive is in the down position Remove chain spring clip type master link Be careful drive arms may move as chain is removed 6 Remove sprockets with shafts still connected Pull or pry on large diameter upper drive sprocket repeat for lower drive sprocket Refer to Figure 20 Figure 18 Using Allen Wrench to Loosen Upper Cup Crank Arm 34 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual aP MIG FoodTech Figure 19 Loosening Lower Crank Arm Note number of thrust washers Figure 20 Sprockets with Shaft being Removed FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 35 eP MIG FoodTech Rebuilding 7 Remove linear shafts With a 3 16 Allen wrench loosen set screws at top and bottom of all three shafts Back screws out at least 1 4 to clear flats on shafts If shafts are stuck use bearing removal puller with 3 8 16 x 2 hex head cap screw to break free shafis Refer to Figure 21 8 Lift out upper and lower drive arms with linkages still attached 9 Disassemble rod end assemblies
33. ologies Inc Multi Fruit Juicer Service amp Operational Manual FME FoodTech Operating Instructions Equipment Check Before plugging the FMC FoodTech Juice Extractor into an electrical outlet the following steps must be performed 1 10 Locate the Citrus Juicer on a level surface This will prevent fruit feed problems Lock both rear casters To lock push down on caster with foot To unlock push again with foot Check waste container Open cart door to verify that waste container is in place A plastic bag may be attached to the hooks above the waste container recommend the Hefty Cinch Sak 30 gallon capacity or equivalent Check juicing components a Twist and pull juice nozzle off b Use key to unlock juicing components cover Open cover and check that juicing components are installed and securely fastened See Figure 1b page 9 Close and lock all access covers There are 4 separate access covers hopper cover juicing components cover cart door cover and back cover NEVER operate extractor unless all covers are in place Replace juice nozzle Make sure juice reservoir is firmly in place Make sure juice reservoir valve is in closed position Check the hopper for foreign objects Remove any foreign objects found in the hopper Make sure floor area around extractor is clean and free of obstructions and water When water is necessary wear appropriate non slip footwear FMC Technologies Inc Mul
34. ologies Inc Multi Fruit Juicer Service amp Operational Manual PVC Food Tech Figure 12 Fruit Lift Plastic Bearings FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 25 FME FoodTech 26 Troubleshooting Extractor will not start Extractor is not plugged into electrical outlet Building circuit breaker has tripped All covers are not completely closed Defective interlock switch eS a Machines built before 1997 have five interlock switches Refer to Figure 13 1 Hopper cover 1 Back cover 1 Cart door cover 1 Juicing Component cover 1 High Level Switch Machines built in 1997 and later have two Schmersal Switches Refer to Figure 15c DISCONNECT ELECTRICAL PLUG before cleaning or maintenance Juicer should HOT run when any cover is open Contact with internal moving parts could cause severe injury or death Da NOT defeat interlack switches a Remove the large cover protecting electrical box and motor Refer to Figure 14 Loosen three screws in juicing area Remove three screws on the right side Remove electrical box cover with on off switch Two on Machines without High Level Switch FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual PVC Food Tech Juicing Switch Back Switch Level Switch Cart Switch Figure 13 Interlock Switch Locations Figure 14 Removal of Switch Cover Panel FMC Technologies In
35. ponents Start by re assembling strainer tube into juice manifold Tighten with spanner wrench Insert orifice tube into bottom of strainer tube Mount juice manifold assembly onto locating pins with orifice tube notch engaging lower drive Tighten spanner screw with spanner wrench Remove red protective cap from cutter Install lower cup and tighten spanner nuts with spanner wrench Install upper cup by slipping pin into stem hole Install splatter shield Refer to Figure 2 page 14 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual FME FoodTech 13 14 15 16 As necessary hose down drive area Remove back cover Turn lock at top 1 4 counter clockwise Pull cover out by using finger hole left of lock then lift and pull cover using finger hole on bottom DO NOT loosen any screws Open hopper cover Open cart door cover Hose down all exposed areas Extractor is water resistant DO NOT use any cleanser in drive area Remove wax build up as needed Cups hopper and other parts may acquire a build up of wax over time a Soak cups for five minutes in an ammonia cleaning solution Rinse thoroughly with sanitizer solution b Wipe hopper and other parts with a cloth soaked in ammonia cleaning solution Remove orange discoloration as needed Equipment may exhibit some build up or orange coloration over time Peralkalate Solution should remove this Wipe with a cloth soaked in any pine based cleaner
36. r Voltage ELECTRICAL DIAGRAM LABEL WIRE ENDS AND COMPONENTS AS SHOWN COO Q ees Q 63 35 DE any 77 IE H SUPE 8 IG Ug oo Figure 51 Electrical Box Assembly Parts 220 Volt FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 73 FME FoodTech 74 Motor Assembly Parts 110Volt 060 00106 C Motor Assembly Parts 220Volt 060 00196 C Item AND ARH k k k M M O Qty Part Number 006 220 004 004 397 137 004 111 022 006 090 209 006 060 044 007 486 118 007 146 010 004 352 398 004 806 070 060 00066 007 661 052 060 00093 005 617 143 004 816 080 060 00197 005 617 144 004 816 080 Description Terminal 10 Ring End for 16 14 Ga Screw Mach Round Head 10 24 x 3 8 S S Nut Hex 10 24 S S Hole Plug Hoffman AS050 1 2 Connector Cord 1 2 NPT 90 Sealing Ring Hubbell 205 09 001 Nut Tru Seal 1 2 NPT Screw Cap Hex 3 8 16 x 1 1 4 S S Washer Lock Reg 3 8 S S Base Motor V Ring Seal C R 400161 5 8 110 Volt Motor Wire 110 Volt 60 HZ Gearmotor 1HP 60 HZ Washer Plain Narrow 3 8 S S 220 Volt Motor Wire 220 Volt 50 HZ Gearmotor 1HP 50 HZ Washer Plain Narrow 3 8 S S FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual aP MIG FoodTech 1 BOLT TOGETHER amp TAPE f X 2 BOLT TOGETHER amp TAPE INSIDE MOTOR JUNCTION BOX INSIDE MOTOR JUNCTION BOX REMOVE FAN SHR
37. rial peel membranes and seeds is collected in a disposable garbage bag for easy removal and disposal The Juice Extractor is solidly built using heavy duty components in all assemblies including the drive It is simple to operate and uses a minimal number of parts ALWAYS follow cleaning and maintenance schedules in this manual to prevent equipment damage For a quick introduction to the FMC FoodTech Juice Extractor please review the diagram on the next page FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual eP MIG FoodTech Single Feed Hole Ear tw 1 4 turn lock Back Cover _ gt SQUEEZY bt Hopper Cover Hopper Drive Cover med On Off Switch 1 4 turn lock Juice Components Cover Stirrer Handle Juice Nozzle Juice Reservoir Juice Reservoir T Valve Cart Cover 1 4 turn lock Cart Door Figure 1a FMC FoodTech Juicer Extractor 8 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual aP MIG FoodTech Pull Pin Upper Cup Fruit Lift Upper Drive Splash Plate Fruit Guide Spanner Nut mo 2 F1 Juice Manifold Lower Cup LJ Strainer Tube Spanner Screw Orifice Tube Lower Drive Splash Plate Note Groove part of Orifice Tube in slot Figure 1b Juicing Components Assembly Garbage Bag Hooks Cleaning Tools Storage Pan Spanner Wrench Waste Container Figure 1c Inside Cart Door FMC Techn
38. s from Upper Drive Arm 38 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual FME FoodTech Figure 25 Removing Bearings from Lower Drive Arm Bearing Installation Washer Bearing Installation Rod Bearing Installation Pilot Figure 26 Installation of Bearings into Drive Arms FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 39 eP MIG FoodTech Rebuilding 12 Reassemble rod end assemblies to drive arms again making sure left hand threaded ends are on the crank arms Refer to Figures 27 and 28 Use Loctite 242 on all fasteners Tighten to torques as shown Make sure rod end lock spacer is installed on rod end in upper drive arm Make sure plastic bearing buttons are installed on each side of lower drive arm 2 Washers Torque to 60 ft lbs 2 Rod End Lock Spacer Torque to 90 ft lbs 2 Washers Torque Cap Screw to 55 ft lbs Figure 27 Completed Assembly of Upper Cup Drive Arm 40 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual eE MIG FoodTech Torque to 25 ft lbs NO Washers Plastic Buttons Both Sides Split This End Torque Cap Screw to 55 ft lbs Torque to 45 ft lbs 2 Washers Figure 28 Completed Assembly of Lower Drive Arm FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 41 eP MIG FoodTech 13 14 15 42 Rebuilding Remove sleeve bearings from main frame Refer
39. t machine and motor did not start or rotate replace entire gear motor If there is a humming noise the capacitor needs to be replaced To replace capacitor remove long cylindrical cover on motor Reseal motor cover with RTV Silicone 28 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual FME FoodTech Figure 15a Sprecher Schuh Electrical Box Electrical Diagram Sprecher Schuh 115 Volt 15 Amp NEUTRAL Plug BLACK So c ao essi ene Figure 15b w 1 Em MACHINES THAT DON T HAVE HIGH LEVEL SWITCH see Next Page For Schmersal Switch Diagram FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 29 FME FoodTech cart 32 DOOR a Schmersol swilch Back 7 Electrical Diogrom 115 Volt 60 Hz with two Schmersal swilches 1997 and later Figure 15c See Page 47 for 220V Diagrams 30 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual PVC Food Tech Troubleshooting Machine starts but shuts off Building circuit breaker is not rated for 20 Amps Extension cord or wiring is too long Shorten extension cord or use heavier gauge wire See page 6 Electrical Specifications All covers not completely closed including cart Extractor may be flexing when squeezing fruit causing switch to open Make sure all latches are completely locked Amperage setting on motor starter on machine set too low See page 26 ite
40. ti Fruit Juicer Service amp Operational Manual PVC Food Tech Operating Instructions Juicing 1 Turn on Extractor Push the ON OFF button to ON position 2 Fruit may be fed into Extractor one at a time Single Feed or in bulk a Single Feed Remove hopper single feed hole cover Twist and pull cover to remove Drop fruit individually down single feed chute through hole in hopper cover DO NOT overload chute or fruit will accidentally be double fed b Bulk Feed Unlock and open the hopper cover Dump up to one carton 40 lbs of fruit into the hopper Fruit may be divided between the carton and carton lid for ease of lifting 3 DO NOT use the single feed chute when hopper is full Fruit will accidentally be double fed 4 Turn off Extractor Push the ON OFF Switch to the OFF position 5 Stir juice Use stirrer handle to stir juice in reservoir before filling containers 6 Fill containers Place container under juice reservoir valve Open valve by turning lever until container is full 7 Clean Extractor If finished juicing clean Extractor as soon as possible See next page for cleaning instructions FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 11 FME FoodTech Cleaning Instructions ALWAYS follow cleaning and maintenance schedules in this manual to prevent equipment damage Clean Extractor as soon as possible for juicing Use a soft towel or sponge to wipe
41. to Figures 29 and 30 The outer upper drive shaft bearing can be removed using puller 1 1 4 removal slug and short threaded removal rod The inner bearing can be removed the same way or can be pressed out using driver The lower shaft bearing can be removed the same way except using 1 removal slug New bearings can be installed by compression Figure 31 by using installation pilot installation washer and long threaded installation rod Light coat of Teflon grease can be used on O D of bearings to aid in installation There are thrust washers next to each bearing on the main frame Make sure the old ones have been removed and new ones installed One side of thrust washer is plain metal Silicone this side and glue them to the frames Typical 4 places DO NOT get silicone on surface of any bearing Before reassembling check all shafts for excessive wear replace as necessary Reassemble parts in the reverse order of removal DO NOT forget to put keys back into crank arms On both crank arms be sure to tighten socket head cap screw first And then the set screw Tighten fasteners to torques shown Lubricate all grease fittings if provided Figure 29 Removing Bearing from Lower Rotary Drive FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual aP MIG FoodTech Bearing Removal Rod Bearing Removal Slug 1 1 4 Figure 30 Removing Bearing from Upper Rotary Drive Figure 31 Installation of
42. trictor Fruit Hole Small Fruit Not Shown Guide Block Small Fruit Not Shown Restrictor Hopper Side Small Fruit Not Shown Restrictor Juicing Side Small Fruit FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual Not Shown aP MIG FoodTech o GG 4 P NN T NN FB KA 9 Or ES Is DDO s GL DE A Ti TP am ne Go Le Figure 37 Juicing Parts FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual FME FoodTech Hopper Assembly Parts 060 00043 F Item Qty Part Number Description 1 1 060 00042 Hopper 2 1 060 00019 Trough 3 1 060 00018 Divider 4 7 004 260 018 Rivet Blind 3 16 x 5 16 Grip 7 16 Ig S S 5 1 060 00089 Button Hopper Bump 6 2 004 260 015 Rivet Blind 3 16 x 1 4 Grip 13 32 Ig S S sad EG Hi i Baan mee I I I I ES I I Li Gb I I l I I HEADS AS SHOWN LI I I I I I i I I HEADS AS SHOWN Figure 38 Hopper Assembly Parts 52 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual FME FoodTech 54 Drive Parts 060 00103 F Item c OO NOU 5 GOM NO mk SH n Qty Part Number 005 220 145 005 221 291 060 00034 005 806 227 004 352 404 004 806 070 004 816 080 060 00117 060 00064 060 00116 060 00010 004 355 116 005 098 113 060 00062 005 576 249 060 00065 005 098 112 005 576 242 004 405 131 060 00061 005 576 06
43. uit lift upper cup drive must be in down position Remove two spanner screws using spanner wrench Remove hopper If hopper does not lift out see Troubleshooting page 26 item a to remove electrical switch cover b Hopper installation DO NOT over tighten spanner screws Hopper is designed to be loose Hopper must be free to bump during each cycle to prevent fruit bridging 22 FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual eE MIG FoodTech Filler Plug Level Plug Drain Plug Figure 8 Checking Oil Level in Gearbox Figure 9a Hopper Removal Figure 9b Bump Button Installation FMC Technologies Inc Multi Fruit Juicer Service amp Operational Manual 23 24 eP MIG FoodTech Periodic Inspection 7 Check alignment of fruit lift Refer to Figure 10 Fruit lift agitator dividers must align with the middle of slots in bottom of hopper a Fruit lift adjustment Refer to Figure 11 Loosen the two cap screws attaching the fruit lift to upper cup drive arm Adjust fruit lift Tighten cap screws b Fruit lift repair If fruit lift is damaged bent but not broken it can be removed and straightened Remove hopper before fruit lift Straighten fruit lift Reinstall fruit lift with Loctite 242 on cap screws 8 Check to make sure two plastic bearing buttons have been installed on bottom face of fruit lift Refer to Figure 12 Figure 10 Fruit Lift Alignment FMC Techn
Download Pdf Manuals
Related Search