Home

2001 oldsmobile aurora owner`s manual

1. 22 0 inches 56 0 cm 6 78 The following replacement parts are for the L47 4 0L V8 Air Cleaner Element AC Type A 1096C Passenger Compartment Air Filter vssnee seaweed sss GM Part 25654414 Engine Oil Filter AC Type PF 58 Fuel Filtet 0 00 AC Type GF 627 Spark Plugs 0 PT16EPR C13 GM Part 12561466 Gap 0 050 inch 1 52 mm Windshield Wiper Blades Type 3 4 otc eoet y tiered Shepard s Hook Length 3 0 6 aiees ieee s obs 22 0 inches 56 0 cm Vehicle Dimensions Length 233i cea ees 205 4 inches 522 0 cm Width sercerrsecreri sikik 74 4 inches 189 0 cm Height 55 4 inches 141 0 cm Wheelbase 113 8 inches 289 1 cm Front Tread 62 5 inches 159 0 cm Rear Tread 62 5 inches 159 0 cm SD Section 7 Maintenance Schedule This section covers the maintenance required for your vehicle Your vehicle needs these services to retain its safety dependability and emission control performance 7 2 Introduction 7 15 7 3 How this Section is Organized 7 19 7 4 Part A Scheduled Maintenance Services 7 21 7 5 Scheduled Maintenance 7 23 Part B Owner Checks and Services Part C Periodic Maintenance Inspections Part D Recommended Fluids and Lubricants Part E Maintenance Record IMPORTANT KEEP ENGINE OIL AT THE PROPER LEVEL AND CHANGE AS RECOMMENDED Protection Plan
2. 7 11 Scheduled Maintenance 60 000 Miles 100 000 km Replace passenger compartment air filter If you drive regularly under dusty conditions the filter may require replacement more often MILEAGE Inspect throttle body bore and valve plates for deposits open the throttle valve i i and inspect all surfaces Clean as required An Emission Control Service See footnote Rotate tires See Tire Inspection and Rotation in the Index for proper rotation pattern and additional information See footnote Inspect engine accessory drive belt An Emission Control Service Replace engine air cleaner filter An Emission Control Service 67 500 Miles 112 500 km Rotate tires See Tire Inspection and Rotation in the Index for proper rotation pattern and additional information See footnote 7 12 Scheduled Maintenance 75 000 Miles 125 000 km Replace passenger compartment air filter If you drive regularly under dusty conditions the filter may require replacement more often MILEAGE i Rotate tires See Tire Inspection and Rotation in the Index for proper a ee rotation pattern and additional information See footnote 82 500 Miles 137 500 km Rotate tires See Tire Inspection and Rotation in the Index for proper rotation pattern and additional information See footnote 90 000 Miles 150 000 km Replace passenger compart
3. 1 Apply your regular brakes and hold the pedal down while you Start your engine Shift into a gear and Release the parking brake 2 Let up on the brake pedal 3 Drive slowly until the trailer is clear of the chocks 4 Stop and have someone pick up and store the chocks Maintenance When Trailer Towing Your vehicle will need service more often when you re pulling a trailer See the Maintenance Schedule for more on this Things that are especially important in trailer operation are automatic transaxle fluid don t overfill engine oil drive belt cooling system and brake system Each of these is covered in this manual and the Index will help you find them quickly If you re trailering it s a good idea to review this information before you start your trip Check periodically to see that all hitch nuts and bolts are tight Engine Cooling When Trailer Towing Your cooling system may temporarily overheat during severe operating conditions See Engine Overheating in the Index 4 37 JD Section 5 Problems on the Road Here you ll find what to do about some problems that can occur on the road 5 2 Hazard Warning Flashers 5 12 Cooling System 5 2 Other Warning Devices 5 18 If a Tire Goes Flat 5 3 Jump Starting 5 18 Changing a Flat Tire 5 8 Towing Your Vehicle 5 28 Compact Spare Tire 5 9 Engine Overheating 5 29 If You re Stuck In Sand Mud Ice or Snow 5 1 Hazard Warning Flashers
4. Automatic Transaxle Check Check the transaxle fluid level add if needed See Automatic Transaxle Fluid in the Index A fluid loss may indicate a problem Check the system and repair if needed At Least Once a Year Key Lock Cylinders Service Lubricate the key lock cylinders with the lubricant specified in Part D Body Lubrication Service Lubricate all body door hinges Also lubricate all hinges and latches including those for the hood rear compartment glove box door console door and any folding seat hardware Part D tells you what to use More frequent lubrication may be required when exposed to a corrosive environment Starter Switch Check Automatic Transaxle Shift Lock Control System Check When you are doing this check the vehicle could move suddenly If it does you or others could be injured Follow the steps below When you are doing this check the vehicle could move suddenly If it does you or others could be injured Follow the steps below 1 Before you start be sure you have enough room around the vehicle 1 Before you start be sure you have enough room around the vehicle It should be parked on a 2 Firmly apply both the parking brake and the regular level surface brake See Parking Brake in the Index if necessary 2 Firmly apply the parking brake See Parking Brake NOTE Do not use the accelerator pedal and be in the Index if necessary ready to turn off the engi
5. The shoulder belt may lock if you pull the belt across you very quickly If this happens let the belt go back slightly to unlock it Then pull the belt across you more slowly 2 Push the latch plate into the buckle until it clicks If the belt stops before it reaches the buckle tilt the latch plate and keep pulling until you can buckle it Pull up on the latch plate to make sure it is secure If the belt is not long enough see Safety Belt Extender at the end of this section Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to 1 31 aN 3252 apr Ps a F K A NN N MO P i So S es a PISS w yy K p g D aa 3 To make the lap part tight pull down on the buckle The lap part of the belt should be worn low and snug on end of the belt as you pull up on the shoulder part the hips just touching the thighs In a crash this applies force to the strong pelvic bones And you d be less likely to slide under the lap belt If you slid under it the belt would apply force at your abdomen This could cause serious or even fatal injuries The shoulder belt should go over the shoulder and across the chest These parts of the body are best able to take belt restraining forces 1 32 The safety belt locks if there s a sudden stop or a crash or if you
6. bird droppings chemicals from industrial chimneys etc can damage your vehicle s finish if they remain on painted surfaces Wash the vehicle as soon as possible If necessary use non abrasive cleaners that are marked safe for painted surfaces to remove foreign matter Exterior painted surfaces are subject to aging weather and chemical fallout that can take their toll over a period of years You can help to keep the paint finish looking new by keeping your vehicle garaged or covered whenever possible Cleaning Aluminum or Chrome Plated Wheels Keep your wheels clean using a soft clean cloth with mild soap and water Rinse with clean water After rinsing thoroughly dry with a soft clean towel A wax may then be applied The surface of these wheels is similar to the painted surface of your vehicle Don t use strong soaps chemicals abrasive polishes abrasive cleaners cleaners with acid or abrasive cleaning brushes on them because you could damage the surface Do not use chrome polish on aluminum wheels Use chrome polish only on chrome plated wheels but avoid any painted surface of the wheel and buff off immediately after application Don t take your vehicle through an automatic car wash that has silicon carbide tire cleaning brushes These brushes can also damage the surface of these wheels Cleaning Tires To clean your tires use a stiff brush with a tire cleaner NOTICE When applying a tire dressing alway
7. ll find that pictures and words work together to explain things quickly Safety Warnings and Symbols You will find a number of safety cautions in this book We use a box and the word CAUTION to tell you about things that could hurt you if you were to ignore the warning These mean there is something that could hurt you or other people In the caution area we tell you what the hazard is Then we tell you what to do to help avoid or reduce the hazard Please read these cautions If you don t you or others could be hurt You will also find a circle with a slash through it in this book This safety symbol means Don t Don t do this or Don t let this happen vii Vehicle Damage Warnings Also in this book you will find these notices NOTICE These mean there is something that could damage your vehicle Viii In the notice area we tell you about something that can damage your vehicle Many times this damage would not be covered by your warranty and it could be costly But the notice will tell you what to do to help avoid the damage When you read other manuals you might see CAUTION and NOTICE warnings in different colors or in different words You ll also see warning labels on your vehicle They use the same words CAUTION or NOTICE Vehicle Symbols These are some of the symbols you may find on your vehicle Also see Warning Lights and Gages in the Index For exa
8. Every 2001 Aurora under warranty is backed with the l following N SS services e Courtesy Transportation Trip Routing L lA NOUr RO320SIOe ASSISTAIANCe 1 800 442 OLDS For vehicles purchased in Canada call 1 800 268 6800 that provides in an emergency Free lockout assistance Free dead battery assistance Free out of fuel assistance Free flat tire change Emergency towing 2001 Oldsmobile Aurora Owner s Manual Litho in Copyright General Motors Corporation 1999 PartN inter 22618961 A First Edition All Rights Reserved ii S o Seats and Seat Controls Safety Belts Keys and Door Locks Remote Lock Control Trunk Release Automatic Transaxle Parking Brake Windows Tilt Wheel Turn Signal M ultifunction Lever Windshield Wipers Cruise Control Interior and Exterior Lamps Table of Contents Seats and Restraint Systems Air Bag Systems Child Restraints Features and Controls VY VVVVVIVYVY Mirrors Storage Compartments Convenience Net Accessory Power Outlet OnStar System If Equipped Sunroof Option HomeLink Transmitter If Equipped Instrument Panel Warning Lights and Gages Driver Information Center Memory and Personalization S Table of Contents cont d Section 4 Q Comfort Controls and Audio Systems Heating and Air Conditioning Radio Theft Deterrent Feature Sett
9. NOTICE If you need a new cap be sure to get the right type Your dealer can get one for you If you get the wrong type it may not fit properly This may cause your malfunction indicator lamp to light and your fuel tank and emissions system may be damaged See Malfunction Indicator Lamp in the Index Filling a Portable Fuel Container Never fill a portable fuel container while it is in your vehicle Static electricity discharge from the container can ignite the gasoline vapor You can be badly burned and your vehicle damaged if this occurs To help avoid injury to you and others Dispense gasoline only into approved containers Do not fill a container while it is inside a vehicle in a vehicle s trunk pickup bed or on any surface other than the ground Bring the fill nozzle in contact with the inside of the fill opening before operating the nozzle Contact should be maintained until the filling is complete Don t smoke while pumping gasoline 6 10 Checking Things Under the Hood An electric fan under the hood can start up and injure you even when the engine is not running Keep hands clothing and tools away from any underhood electric fan Things that burn can get on hot engine parts and start a fire These include liquids like gasoline oil coolant brake fluid windshield washer and other fluids and plastic or rubber You or others could be burned Be careful not to drop or spill things that
10. This program available to qualified applicants can reimburse you up to 1 000 toward aftermarket driver or passenger adaptive equipment you may require for your vehicle hand controls wheelchair scooter lifts etc This program can also provide you with free resource information such as area driver assessment centers and mobility equipment installers The program is available for a limited period of time from the date of vehicle purchase lease See your dealer for more details or call the GM Mobility Assistance Center at 1 800 323 9935 Text telephone TTY users call 1 800 833 9935 GM of Canada also has a Mobility Program Call 1 800 GM DRIVE 463 7483 for details When calling from outside Canada please dial 1 905 644 3063 All TTY users call 1 800 263 3830 8 5 Oldsmobile Roadside Assistance Program Features and Benefits Security While You Travel 1 800 442 OLDS 6537 As the proud owner of a new Oldsmobile vehicle you are automatically enrolled in the Oldsmobile Roadside Assistance program This value added service is intended to provide you with peace of mind as you drive in the city or travel the open road 8 6 Oldsmobile s Roadside Assistance toll free number is staffed by courteous and capable Roadside Assistance Representatives who are available 24 hours a day 365 days a year We will provide the following services during the Bumper to Bumper warranty period at no expense
11. s the time for evasive action steering around the problem Your vehicle can perform very well in emergencies like these First apply your brakes See Braking in Emergencies earlier in this section It is better to remove as much speed as you can from a possible collision Then steer around the problem to the left or right depending on the space available 4 12 An emergency like this requires close attention and a quick decision If you are holding the steering wheel at the recommended 9 and 3 o clock positions you can turn it a full 180 degrees very quickly without removing either hand But you have to act fast steer quickly and just as quickly straighten the wheel once you have avoided the object The fact that such emergency situations are always possible is a good reason to practice defensive driving at all times and wear safety belts properly Off Road Recovery You may find that your right wheels have dropped off the edge of a road onto the shoulder while you re driving OFF ROAD RECOVERY 9 LEFT APPROX QUARTER TURN edge of paved surface If the level of the shoulder is only slightly below the pavement recovery should be fairly easy Ease off the accelerator and then if there is nothing in the way steer so that your vehicle straddles the edge of the pavement You can turn the steering wheel up to one quarter turn until the right front tire contacts the pavement edge Then turn your steering w
12. B and C Those grades represent the tire s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete A tire marked C may have poor traction performance Warning The traction grade assigned to this tire is based on straight ahead braking traction tests and does not include acceleration cornering hydroplaning or peak traction characteristics Temperature A B C The temperature grades are A the highest B and C representing the tire s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel Sustained high temperature can cause the material of the tire to degenerate and reduce tire life and excessive temperature can lead to sudden tire failure The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No 109 Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law Warning The temperature grade for this tire is established for a tire that is properly inflated and not overloaded Excessive speed underinflation or excessive loading either separately or in combination can cause heat buildup and possible tire failure Wheel Alignment and Tire Balance The wheels on your vehicle were aligned and balanced caref
13. Defensive driving requires that a driver concentrate on the driving task Anything that distracts from the driving task such as concentrating on a cellular telephone call reading or reaching for something on the floor makes proper defensive driving more difficult and can even cause a collision with resulting injury Ask a passenger to help do things like this or pull off the road in a safe place to do them yourself These simple defensive driving techniques could save your life Drunken Driving Death and injury associated with drinking and driving is a national tragedy It s the number one contributor to the highway death toll claiming thousands of victims every year Alcohol affects four things that anyone needs to drive a vehicle Judgment Muscular Coordination Vision Attentiveness Police records show that almost half of all motor vehicle related deaths involve alcohol In most cases these deaths are the result of someone who was drinking and driving In recent years over 17 000 annual motor vehicle related deaths have been associated with the use of alcohol with more than 300 000 people injured Many adults by some estimates nearly half the adult population choose never to drink alcohol so they never drive after drinking For persons under 21 it s against the law in every U S state to drink alcohol There are good medical psychological and developmental reasons for these laws The
14. If your vehicle starts to slide ease your foot off the accelerator pedal and quickly steer the way you want the vehicle to go If you start steering quickly enough your vehicle may straighten out Always be ready for a second skid if it occurs If you have Stabilitrak you may see the STABILITY ACTIVE message on the Driver Information Center See Stability Active Message in the Index Of course traction is reduced when water snow ice gravel or other material is on the road For safety you ll want to slow down and adjust your driving to these conditions It is important to slow down on slippery surfaces because stopping distance will be longer and vehicle control more limited While driving on a surface with reduced traction try your best to avoid sudden steering acceleration or braking including engine braking by shifting to a lower gear Any sudden changes could cause the tires to slide You may not realize the surface is slippery until your vehicle is skidding Learn to recognize warning clues such as enough water ice or packed snow on the road to make a mirrored surface and slow down when you have any doubt Remember Any anti lock brake system ABS helps avoid only the braking skid 4 15 Driving at Night Night driving is more dangerous than day driving One reason is that some drivers are likely to be impaired by al
15. Your hazard warning flashers let you warn others They also let police know you have a problem Your front and rear turn signal lamps will flash on and off 5 2 To turn on the hazard warning flashers press and release the button located in the center of the instrument panel The indicators for the turn signals will flash on and off Your hazard flashers work no matter what position your key is in and even if the key isn t in To turn off the flashers press the button down again When the flashers are on your turn signals won t work Other Warning Devices If you carry reflective triangles you can set one up at the side of the road about 300 feet 100 m behind your vehicle Jump Starting If your battery has run down you may want to use another vehicle and some jumper cables to start your vehicle But please use the following steps to do it safely NOTICE Ignoring these steps could result in costly damage to your vehicle that wouldn t be covered by your warranty The ACDelco battery in your vehicle has a built in hydrometer Do not charge test or jump start the battery if the hydrometer looks clear or light yellow Replace the battery when there is a clear or light yellow hydrometer and a cranking complaint Batteries can hurt you They can be dangerous because They contain acid that can burn you They contain gas that can explode or ignite They contain enough electricity to burn y
16. every 3 000 miles 5 000 km or sooner Remember to reset the Oil Life System whenever the oil is changed How to Reset the Oil Life System Always reset the engine Oil Life System to 100 after every oil change It will not reset itself To reset the OIL LIFE reminder do the following 1 With the ignition on press the SELECT right arrow button to OIL so the OIL LIFE percentage is displayed 2 Press RESET and hold for five seconds OIL LIFE XXX will appear and then when the button is released OIL LIFE 100 will be displayed 6 19 What to Do with Used Oil Did you know that used engine oil contains certain elements that may be unhealthy for your skin and could even cause cancer Don t let used oil stay on your skin for very long Clean your skin and nails with soap and water or a good hand cleaner Wash or properly throw away clothing or rags containing used engine oil See the manufacturer s warnings about the use and disposal of oil products Used oil can be a real threat to the environment If you change your own oil be sure to drain all free flowing oil from the filter before disposal Don t ever dispose of oil by putting it in the trash pouring it on the ground into sewers or into streams or bodies of water Instead recycle it by taking it to a place that collects used oil If you have a problem properly disposing of your used oil ask your dealer a service station or a local recycling center for help 6
17. interior side of the windshield behind the rearview mirror and is used to automatically operate the wipers by monitoring the amount of moisture that is on the windshield The Rainsense system can be activated by moving the wiper lever to INT Set the wiper control band to one of the five sensitivity settings within the delay area The bottom INT ADJ position is the lowest sensitivity setting This allows more water to collect on the windshield between wipes You can increase the sensitivity of the system and the frequency of wipes by turning the INT ADJ band up towards the wider lines A single wipe will occur each time you turn the wiper control band to a higher sensitivity setting The Rainsense wipers operate in a delay mode as well as a continuous low or high speed depending on the amount of moisture on the windshield and the sensitivity setting The MIST and wash cycles operate as normal and are not affected by the Rainsense function 2 40 NOTICE The wipers must be turned off when going through a car wash to avoid damage It is important to note that the Rainsense delay wiping feature can be overridden at any time by manually changing the wiper control to LO or HI speed NOTICE Do not place stickers or other items on the exterior glass surface directly in front of the rainsensor Doing this could cause the rainsensor to malfunction Windshield Washer The lever on the right side of your steering column
18. locking of the vehicle can be made active or inactive through the DIC When DELAY LOCK OF DOORS appears on the display use the SELECT right arrow button to toggle between YES and NO 2 88 When you have made your choice press the SELECT down arrow button to record your selection and move on to the next choice For more information on this feature see Delayed Locking in the Index Perimeter Lighting Personalization When the unlock symbol on the transmitter is pressed the Daytime Running Lamps parking lamps and back up lamps will turn on if it is dark enough outside You can control activation of this feature by choosing YES or NO when the PERIMETER LIGHTS choice is displayed on the DIC Make your choice by pressing the SELECT right arrow button and record your choice by pressing the SELECT down arrow button You will then be prompted to choose a TIMEOUT period The EXT LIGHTS TIMEOUT feature can be changed to the desired setting by using the SELECT right arrow button to toggle from 5 to 30 seconds Each toggle will increase the time by 5 seconds Once the desired timeout is displayed press SELECT down arrow to record your choice and move on to the next personal choice feature For more information on this feature see Perimeter Lighting in the Index Driver ID This feature displays the driver ID as identified by the DIC If you choose YES when DISPLAY DRIVER ID is shown on the DIC the driver number will
19. new features With RDS the radio can Seek only to RDS stations with the types of programs you want to listen to seek to RDS stations with traffic announcements receive announcements concerning local and national emergencies and receive and display messages from RDS radio stations RDS features are only available for use on FM stations which broadcast RDS information The RDS features of your radio rely upon receiving specific RDS information from these stations These features will only work when the RDS information is available In rare cases a radio station may broadcast incorrect information that will cause the radio features to work improperly If this happens please contact the radio station When you are tuned to an RDS station the station name will appear on the display instead of the frequency Most RDS stations provide their station name the time of day and a Program Type PTY for their current programming TRAF Press this button to receive traffic announcements The traffic announcement brackets will appear on the display TRAF will appear on the display if the tuned station broadcasts traffic announcements If the current tuned station does not broadcast traffic announcements the radio will seek to a station that does When the radio finds a station that broadcasts traffic announcements it will stop If no station is found NO TRAFFIC will appear on the display When a traffic announcement comes on
20. park in a busy well lit area Put your valuables in a storage area like your trunk or glove box Be sure to close and lock the storage area Close all windows Move the trunk release lockout switch to ON Lock the glove box Lock all doors except the driver s Give the valet key to the valet Then take the master key with you Universal Theft Deterrent Your vehicle has a theft deterrent alarm system With this system if your ignition is off the SECURITY light will flash as you open the door This light reminds you to activate the theft deterrent system To activate it do the following SECURITY 1 Open the door 2 Lock the door with the power door lock switch or remote lock control system The SECURITY light should come on and stay on 3 Close all doors The SECURITY light should go off after about 30 seconds The security system is not armed until the SECURITY light is off If the SECURITY light stays on or flashes when the ignition is turned on there is a problem with the system and the vehicle should be serviced If the SECURITY light comes on for one minute and then shuts off while the ignition is on the security system has detected a problem See your dealer for service If a door or the trunk is opened without the key or remote lock control transmitter the alarm will go off Your vehicle s lamps will flash and the horn will sound for 30 seconds then will go off to save battery power Rem
21. requirements of NLGI 2 Category LB or GC LB Multi Purpose Lubricant Superlube GM Part No 12346241 or equivalent USAGE FLUID LUBRICANT Fuel Door Hinge Glove Box Door Console Door Hinge Rear Compartment Lid Hinges Multi Purpose Lubricant Superlube GM Part No 12346241 or equivalent Weatherstrip Dielectric Silicone Grease GM Conditioning Part No 12345579 or equivalent Part E Maintenance Record After the scheduled services are performed record the date odometer reading and who performed the service in the boxes provided after the maintenance interval Any additional information from Owner Checks and Services or Periodic Maintenance can be added on the following record pages Also you should retain all maintenance receipts Your owner information portfolio is a convenient place to store them Maintenance Record ODOMETER DATE READING SERVICED BY MAINTENANCE PERFORMED Maintenance Record ODOMETER DATE READING SERVICED BY MAINTENANCE PERFORMED Maintenance Record ODOMETER DATE READING SERVICED BY MAINTENANCE PERFORMED Maintenance Record ODOMETER DATE READING SERVICED BY MAINTENANCE PERFORMED Maintenance Record ODOMETER DATE READING SERVICED BY MAINTENANCE PERFORMED Maintenance Record ODOMETER DATE READING SERVICED BY MAINTENANCE PERFORMED Maintenance Record ODOMETER DATE READING SERVICED BY MAINTENANCE PERFORMED Maintenance Record OD
22. s designed threshold level The threshold level can vary with specific vehicle design Side impact air bags are not designed to inflate in frontal or near frontal impacts rollovers or rear impacts because inflation would not help the occupant A side impact air bag will only deploy on the side of the vehicle that is struck 1 26 In any particular crash no one can say whether an air bag should have inflated simply because of the damage to a vehicle or because of what the repair costs were For frontal air bags inflation is determined by the angle of the impact and how quickly the vehicle slows down in frontal and near frontal impacts For side impact air bags inflation is determined by the location and severity of the impact What makes an air bag inflate In an impact of sufficient severity the air bag sensing system detects that the vehicle is in a crash For both frontal and side impact air bags the sensing system triggers a release of gas from the inflator which inflates the air bag The inflator air bag and related hardware are all part of the air bag modules inside the steering wheel instrument panel and the side of the front seatbacks closest to the door How does an air bag restrain In moderate to severe frontal or near frontal collisions even belted occupants can contact the steering wheel or the instrument panel In moderate to severe side collisions even belted occupants can contact the inside of the
23. the vehicle Be sure to properly secure any child restraint in your vehicle even when no child is in it Top Strap Some child restraints have a top strap or top tether It can help restrain the child restraint during a collision For it to work a top strap must be properly anchored to the vehicle If the child restraint does not have a top strap one can be obtained in kit form for many child restraints Ask the child restraint manufacturer whether or not a kit is available 1 45 1 46 In Canada the law requires that forward facing child restraints have a top strap and that the strap be anchored In the United States some child restraints also have a top strap If your child restraint has a top strap it should be anchored Your vehicle has top strap anchors already installed for the rear seating positions You ll find them behind the rear seat on the filler panel In order to get to a bracket you ll have to open the trim cover Anchor the top strap to this bracket Once you have the top strap anchored you ll be ready to secure the child restraint itself Securing a Child Restraint in a Rear Outside Seat Position and in the Center Rear Seat Position Lap Shoulder Belt If the center rear seating position has a lap shoulder belt with a retractor follow these instructions to secure a child restraint in the center rear seat If the center rear seating position has a lap only belt with no r
24. 5 L Engine Crankcase 6 0 quarts 5 7 L When changing filter up to 0 5 quart 0 5 L more oil may be needed 6 76 Fuel Tank 18 5 U S gallons 70 0 L Air Conditioning Refrigerant See refrigerant charge label under the hood Power Steering Pump Only acsccscneceawe se pee 1 0 pint 0 5 L Complete System 1 5 pints 0 7 L Tire Pressures See Tire Loading Information label on the rear edge of the driver s door Wheel Nut Torque 100 lb ft 140 N m Engine Code L47 4 0L V8 Automatic Transaxle Overdrive When draining or replacing torque converter more fluid may be needed Pan Removal Drain Plug and Replacement 11 0 quarts 10 4 L After Complete Overhaul 12 6 quarts 12 0 L When performing either transaxle procedure check fluid level when done More fluid may be needed Cooling System 13 0 quarts 10 5 L Engine Crankcase 7 0 quarts 6 6 L When changing filter up to 0 5 quart 0 5 L more oil may be needed Fuel Tank 17 5 U S gallons 66 2 L Air Conditioning Refrigerant See refrigerant charge label under the hood Power Steering Pump Only 1 0 pint 0 5 L Complete System 1 5 pints 0 7 L Tire Pressures See Tire Loading Information label on the rear edge of the driver s door Wheel Nut Torque 100 lb ft 140 N m All capacities ar
25. Engine oil with the American Petroleum Institute Certified for Gasoline Engines starburst symbol of the proper viscosity To determine the preferred viscosity for your vehicle s engine see Engine Oil in the Index 50 50 mixture of clean drinkable water and use only GM Goodwrench DEX COOL or Havoline DEX COOL Coolant See Engine Coolant in the Index Engine Coolant USAGE FLUID LUBRICANT Hydraulic Delco Supreme 11 Brake Fluid Brake System GM Part No 12377967 or equivalent DOT 3 brake fluid GM Optikleen Washer Solvent GM Part No 1051515 or equivalent Chassis Lubricant GM Part No 12377985 or equivalent or lubricant meeting requirements of NLGI 2 Category LB or GC LB GM Power Steering Fluid GM Part No 1052884 1 pint 1050017 1 quart or equivalent Automatic DEXRON III Automatic Transaxle Transmission Fluid Multi Purpose Lubricant Superlube GM Part No 12346241 or equivalent Windshield Washer Solvent Parking Brake Cable Guides Power Steering System 7 21 USAGE FLUID LUBRICANT Floor Shift Linkage Hood Latch Assembly Secondary Latch Pivots Spring Anchor and Release Pawl Hood and Door Hinges 7 22 Lubriplate Lubricant Aerosol GM Part No 12346293 or equivalent or lubricant meeting requirements of NLGI 2 Category LB or GC LB Lubriplate Lubricant Aerosol GM Part No 12346293 or equivalent or lubricant meeting
26. SCAN controls just as you do for the radio The display will show TAPE and an arrow showing which side of the tape is playing The tape player automatically begins playing the other side when it reaches the end of the tape Your tape bias is set automatically when a metal or chrome tape is inserted If you want to insert a tape when the ignition is off first press EJECT or the RCL button If an error appears on the radio display the tape won t play because of an error TIGHT TAPE is displayed when the tape is tight and the player can t turn the tape hubs Remove the tape Hold the tape with the open end down and try to turn the right hub counterclockwise with a pencil Turn the tape over and repeat If the hubs do not turn easily your tape may be damaged and should not be used in the player Try a new tape to make sure your player is working properly BROKEN TAPE is displayed when the tape is broken Try anew tape WRAPPED is displayed when the tape is wrapped around the tape head Attempt to get the cassette out Try anew tape 3 16 If any error occurs repeatedly or if an error can t be corrected please contact your dealer If your radio displays an error message write it down and provide it to your dealer when reporting the problem REV 1 Press this button to reverse the tape rapidly Press it again to return to playing speed The radio will play the last selected station while the tape reverses You may select s
27. See Tire Inspection and Rotation in the Index for proper rotation pattern and additional information See footnote Replace engine air cleaner filter An Emission Control Service 37 500 Miles 62 500 km Rotate tires See Tire Inspection and Rotation in the Index for proper rotation pattern and additional information See footnote 45 000 Miles 75 000 km Replace passenger compartment air filter If you drive regularly under dusty conditions the filter may require replacement more often MILEAGE Rotate tires See Tire Inspection and Rotation in the Index for proper a e rotation pattern and additional information See footnote 7 10 Scheduled Maintenance 50 000 Miles 83 000 km hange automatic transaxle fluid and bottom screens if the vehicle is mainl ACTUAL Sa under one or more of these conditions y In heavy city traffic where the outside temperature regularly reaches ooo Ee 90 F 32 C or higher In hilly or mountainous terrain When doing frequent trailer towing Uses such as found in taxi police or delivery service If you do not use your vehicle under any of these conditions change the fluid and filter at 100 000 miles 166 000 km 52 500 Miles 87 500 km Rotate tires See Tire Inspection and Rotation in the Index for proper rotation pattern and additional information See footnote
28. Things Under the Hood 6 64 Underbody Maintenance 6 15 Engine Oil 6 64 Chemical Paint Spotting 6 20 Engine Air Cleaner Filter 6 65 GM Vehicle Care Appearance Materials 6 23 Automatic Transaxle Fluid 6 66 Vehicle Identification Number VIN 6 26 Engine Coolant 6 67 Electrical System 6 31 Windshield Washer Fluid 6 71 Removing the Rear Seat Cushion 6 32 Brakes 6 75 Replacement Bulbs 6 35 Battery 6 76 Capacities and Specifications 6 37 Bulb Replacement 6 78 Normal Maintenance Replacement Parts 6 48 Tires Service Your dealer knows your vehicle best and wants you to be happy with it We hope you ll go to your dealer for all your service needs You ll get genuine GM parts and GM trained and supported service people We hope you ll want to keep your GM vehicle all GM Genuine GM parts have one of these marks ACDelco n T NINE adele Doing Your Own Service Work If you want to do some of your own service work you ll want to use the proper service manual It tells you much more about how to service your vehicle than this manual can To order the proper service manual see Service and Owner Publications in the Index Your vehicle has an air bag system Before attempting to do your own service work see Servicing Your Air Bag Equipped Vehicle in the Index You should keep a record with all parts receipts and list the mileage and the date of any service work you perform See Maintenance Record in th
29. Traction Control System in the Index 4 6 Braking Braking action involves perception time and reaction time First you have to decide to push on the brake pedal That s perception time Then you have to bring up your foot and do it That s reaction time Average reaction time is about 3 4 of a second But that s only an average It might be less with one driver and as long as two or three seconds or more with another Age physical condition alertness coordination and eyesight all play a part So do alcohol drugs and frustration But even in 3 4 of a second a vehicle moving at 60 mph 100 km h travels 66 feet 20 m That could be a lot of distance in an emergency so keeping enough space between your vehicle and others is important And of course actual stopping distances vary greatly with the surface of the road whether it s pavement or gravel the condition of the road wet dry icy tire tread the condition of your brakes the weight of the vehicle and the amount of brake force applied Avoid needless heavy braking Some people drive in spurts heavy acceleration followed by heavy braking rather than keeping pace with traffic This is a mistake Your brakes may not have time to cool between hard stops Your brakes will wear out much faster if you do a lot of heavy braking If you keep pace with the traffic and allow realistic following distances you will eliminate a lot of unnecessary braking
30. Water can cause the solution to freeze The windshield washer fluid reservoir is located at the front of the engine compartment on the water doesn t clean as well as washer fluid passenger s side See Fill your washer fluid tank only Engine Compartment three quarters full when it s very cold WASHER Overview in the Index This allows for expansion if freezing occurs FEUD for more information which could damage the tank if it is on location completely full h _ Don t use engine coolant antifreeze in your windshield washer It can damage your washer system and paint When the tank contains 0 5 quarts 0 5 liters or less the message LOW WASHER FLUID will be displayed on the Driver Information Center DIC and damage your washer fluid tank and other parts of the washer system Also 6 31 Brakes Brake Fluid See Engine Compartment Overview in the Index for more information on location Your brake master cylinder reservoir is on the driver s side of the engine compartment It is filled with DOT 3 brake fluid There are only two reasons why the brake fluid level in the reservoir might go down The first is that the brake fluid goes down to an acceptable level during normal brake lining wear When new linings are put in the fluid level goes back up The other reason is that fluid is leaking out of the brake system If it is you should have your brake system fixed since a
31. Your Driving and the Road Here you ll find information about driving on different kinds of roads and in varying weather conditions We ve also included many other useful tips on driving 4 2 Defensive Driving 4 17 4 3 Drunken Driving 4 20 4 6 Control of a Vehicle 4 21 4 6 Braking 4 22 4 9 Traction Control System 4 23 4 11 Steering 4 23 4 13 Off Road Recovery 4 25 4 13 Passing 4 28 4 15 Loss of Control 4 29 4 16 Driving at Night 4 31 Driving in Rain and on Wet Roads City Driving Freeway Driving Before Leaving on a Long Trip Highway Hypnosis Hill and Mountain Roads Winter Driving Recreational Vehicle Towing Loading Your Vehicle Towing a Trailer Defensive Driving The best advice anyone can give about driving is Drive defensively Please start with a very important safety device in your vehicle Buckle up See Safety Belts in the Index Defensive driving really means be ready for anything On city streets rural roads or freeways it means always expect the unexpected Assume that pedestrians or other drivers are going to be careless and make mistakes Anticipate what they might do Be ready for their mistakes Rear end collisions are about the most preventable of accidents Yet they are common Allow enough following distance It s the best defensive driving maneuver in both city and rural driving You never know when the vehicle in front of you is going to brake or turn suddenly
32. also controls your windshield washer To spray washer fluid on the windshield push the button on the end of the lever The wipers will clear the window and then either stop or return to your preset speed For more washer cycles push and hold the button In freezing weather don t use your washer until the windshield is warmed Otherwise the washer fluid can form ice on the windshield blocking your vision Ice build up can block washer nozzles Remove ice for proper operation If the fluid level in the windshield washer bottle is low the message LOW WASHER FLUID will appear in the Driver Information Center See Windshield Washer Fluid in the Index Cruise Control With cruise control you can maintain a speed of about 25 mph 40 km h or more without keeping your foot on the accelerator This is helpful on long trips Cruise control does not work at speeds below about 25 mph 40 km h When you apply your brakes the cruise control shuts off Cruise control can be dangerous where you can t drive safely at a steady speed So don t use your cruise control on winding roads or in heavy traffic Cruise control can be dangerous on slippery roads On such roads fast changes in tire traction can cause needless wheel spinning and you could lose control Don t use cruise control on slippery roads 2 41 If your vehicle is in cruise control when the traction control system begins to limit wheel spin
33. and Wiper Blades If the windshield is not clear after using the windshield washer or if the wiper blade chatters when running wax sap or other material may be on the blade or windshield Clean the outside of the windshield with GM Windshield Cleaner Bon Ami Powder non scratching glass cleaning powder GM Part No 1050011 The windshield is clean if beads do not form when you rinse it with water Grime from the windshield will stick to the wiper blades and affect their performance Clean the blade by wiping vigorously with a cloth soaked in full strength windshield washer solvent Then rinse the blade with water Check the wiper blades and clean them as necessary replace blades that look worn Weatherstrips Silicone grease on weatherstrips will make them last longer seal better and not stick or squeak Apply silicone grease with a clean cloth at least every six months During very cold damp weather more frequent application may be required See Recommended Fluids and Lubricants in the Index 6 61 Cleaning the Outside of Your Vehicle The paint finish on your vehicle provides beauty depth of color gloss retention and durability Washing Your Vehicle The best way to preserve your vehicle s finish is to keep it clean by washing it often with lukewarm or cold water Don t wash your vehicle in the direct rays of the sun Use a car washing soap Don t use strong soaps or chemical detergents Be sure to r
34. as soon as you can Your spare will last longer and be in good shape in case you need it again 5 28 NOTICE When the compact spare is installed don t take your vehicle through an automatic car wash with guide rails The compact spare can get caught on the rails That can damage the tire and wheel and maybe other parts of your vehicle Don t use your compact spare on other vehicles And don t mix your compact spare tire or wheel with other wheels or tires They won t fit Keep your spare tire and its wheel together NOTICE Tire chains won t fit your compact spare Using them can damage your vehicle and can damage the chains too Don t use tire chains on your compact spare If You re Stuck In Sand Mud Ice or Snow In order to free your vehicle when it is stuck you will need to spin the wheels but you don t want to spin your wheels too fast The method known as rocking can help you get out when you re stuck but you must use caution If you let your tires spin at high speed they can explode and you or others could be injured And the transaxle or other parts of the vehicle can overheat That could cause an engine compartment fire or other damage When you re stuck spin the wheels as little as possible Don t spin the wheels above 35 mph 55 km h as shown on the speedometer NOTICE Spinning your wheels can destroy parts of your vehicle as well as the tires If you s
35. be displayed every time the ignition is turned on If you choose NO when DISPLAY DRIVER ID is shown on the DIC the driver number can be displayed by pressing either a button on the remote lock control transmitter or a memory seat button Memory Seat Recall If Equipped This feature recalls the position of the driver s seat When this feature is active the memory seat and mirror positions will be recalled for the identified driver when the remote lock control transmitter is used to enter the vehicle You can program this feature to be active by choosing YES when the KEY FOB MEMORY SEAT choice appears or inactive by choosing NO when the KEY FOB MEMORY SEAT choice appears on the DIC Make your choices by pressing the SELECT right arrow button and store them in memory by pressing the SELECT down arrow button You can also program this feature to recall your memory seat position or the exit seat position Select YES for KEY FOB MEMORY SEAT then use the SELECT right arrow button to toggle between DRIVING POSITION YES and EXIT POSITION YES When the desired position is displayed on the DIC press the SELECT down arrow button to save that position in memory and move on to the next selection For more information on this feature see Memory Seat and Mirrors in the Index Parallel Park Assist If Equipped The parallel park assist mirror which tips the passenger mirror while the vehicle is in REVERSE R can be made active
36. become loose and even come off This could lead to an accident Be sure to use the correct wheel nuts If you have to replace them be sure to get new GM original equipment wheel nuts Stop somewhere as soon as you can and have the nuts tightened with a torque wrench to 100 lb ft 140 N m NOTICE Improperly tightened wheel nuts can lead to brake pulsation and rotor damage To avoid expensive brake repairs evenly tighten the wheel nuts in the proper sequence and to the proper torque specification 12 When the flat tire has been repaired or replaced install the wheel cover Be sure to position the alignment pin on the cover with the notch in the wheel Apply pressure around the edge of the cap to snap it in place Do not use a hammer or mallet to install the cover Store the wheel cover in the trunk until you have replaced the compact spare tire with a regular tire NOTICE Wheel covers won t fit on your compact spare If you try to put a wheel cover on your compact spare you could damage the cover or the spare 5 25 Storing the Flat Tire and Tools Storing a jack a tire or other equipment in the passenger compartment of the vehicle could cause injury In a sudden stop or collision loose equipment could strike someone Store all these in the proper place 5 26 Store the flat tire as far forward in the trunk as possible Store the jack and wheel wrench in their compartment in the trunk Fo
37. brake system parts For example just a few drops of mineral based oil such as engine oil in your brake system can damage brake system parts so badly that they II have to be replaced Don t let someone put in the wrong kind of fluid If you spill brake fluid on your vehicle s painted surfaces the paint finish can be damaged Be careful not to spill brake fluid on your vehicle If you do wash it off immediately See Appearance Care in the Index 6 33 Brake Wear Your vehicle has four wheel disc brakes Disc brake pads have built in wear indicators that make a high pitched warning sound when the brake pads are wom and new pads are needed The sound may come and go or be heard all the time your vehicle is moving except when you are pushing on the brake pedal firmly The brake wear warning sound means that soon your brakes won t work well That could lead to an accident When you hear the brake wear warning sound have your vehicle serviced NOTICE Continuing to drive with worn out brake pads could result in costly brake repair 6 34 Some driving conditions or climates may cause a brake squeal when the brakes are first applied or lightly applied This does not mean something is wrong with your brakes Properly torqued wheel nuts are necessary to help prevent brake pulsation When tires are rotated inspect brake pads for wear and evenly tighten wheel nuts in the proper sequence to GM torque specificat
38. child is sitting in a rear seat outside position see Rear Safety Belt Comfort Guides in the Index If the child is so small that the shoulder belt is still very close to the child s face or neck you might want to place the child in a seat that has a lap belt if your vehicle has one 1 56 Never do this Here a child is sitting in a seat that has a lap shoulder belt but the shoulder part is behind the child If the child wears the belt in this way in a crash the child might slide under the belt The belt s force would then be applied right on the child s abdomen That could cause serious or fatal injuries Wherever the child sits the lap portion of the belt should be worn low and snug on the hips just touching the child s thighs This applies belt force to the child s pelvic bones in a crash Safety Belt Extender If the vehicle s safety belt will fasten around you you should use it But if a safety belt isn t long enough to fasten your dealer will order you an extender It s free When you go in to order it take the heaviest coat you will wear so the extender will be long enough for you The extender will be just for you and just for the seat in your vehicle that you choose Don t let someone else use it and use it only for the seat it is made to fit To wear it just attach it to the regular safety belt 1 57 Checking Your Restraint Systems Now and then make sure the safety belt
39. disc number on the radio display will go to that of the next available CD 6 Press this button to select the previous disc in the magazine Each time 6 is pressed the disc number on the radio display will go to that of the previous available CD RCL Press this button to see how long the current track has been playing To change what is normally shown on the display track or elapsed time press the button until you see the display you want then hold the button until the display flashes While elapsed time is showing EL TM will appear on the display SEEK Press the SEEK reverse arrow while playing a CD to go back to the start of the current track if more than eight seconds have played Press the SEEK forward arrow and it will go to the next higher track on the disc If the button is pressed more than once the player will continue moving backward or forward through the disc TRACK SCAN Press and hold one of the SEEK arrows for two seconds until TRACK SCAN appears on the display and a chime is heard The first few seconds of each track on the current disc will be played The sound will mute while scanning The SCAN icon will be lit and a T will blink to indicate track scan mode Press SEEK again to stop TRACK SCAN DISC SCAN Press and hold one of the SEEK arrows for four seconds until DISC SCAN appears on the display and a double chime is heard The first few seconds of each disc will be heard The sound will mute whi
40. door handle rearward To lock the door move the manual door lock control forward Central Door Unlocking System If the key is held in the outside key cylinder unlock position for more than two seconds all doors will unlock All doors will also unlock if the key is turned to the unlock position twice within three seconds Power Door Locks With power door locks you can lock or unlock all the doors of your vehicle using the driver s or the front passenger s door lock switch Door Ajar Reminder If a door is not fully closed when the transaxle is in gear a chime will sound and the Driver Information Center DIC will display one of these messages DRIVERS DOOR AJAR PASSENGER DOOR AJAR LEFT REAR DOOR AJAR RIGHT REAR DOOR AJAR Programmable Automatic Door Locks This is a personalization feature that programs your door locks to automatically lock or unlock your vehicle This feature also allows you to program the vehicle to lock all doors when shifting out of PARK P Also you can program the door locks to do one of the following Unlock just the driver s door when shifting back into PARK P unlock all doors when shifting back into PARK P unlock just the driver s door when turning the ignition to LOCK unlock all doors when turning the ignition to LOCK or no automatic door unlock when shifting into PARK P or turning the ignition to LOCK You can also program this feature
41. due to overnight warranty repairs your dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle you obtained at actual cost up to a maximum of 30 00 per day supported by receipts This requires that you sign and complete a rental agreement and meet state local and rental vehicle provider requirements Requirements vary and may include minimum age requirements insurance coverage credit card etc You are responsible for fuel usage charges and may also be responsible for taxes levies usage fees excessive mileage or rental usage beyond the completion of the repair Generally it is not possible to provide a like vehicle as a courtesy rental Additional Program Information Courtesy Transportation is available during the Bumper to Bumper warranty coverage period but it is not part of the New Vehicle Limited Warranty A separate booklet entitled Warranty and Owner Assistance Information furnished with each new vehicle provides detailed warranty coverage information Courtesy Transportation is available only at participating dealers and all program options such as shuttle service may not be available at every dealer Please contact your dealer for specific information about availability All Courtesy Transportation arrangements will be administered by appropriate dealer personnel Canadian Vehicles For warranty repairs during the Complete Vehicle Coverage period of the Gener
42. feel or hear the system working but this is normal If your vehicle is in cruise control when the traction control system begins to limit wheel spin the cruise control will automatically disengage When road conditions allow you to safely use it again you may reengage the cruise control See Cruise Control in the Index This light should come on briefly when you start the engine If it stays on TRAC or comes on while you OFF are driving there s a problem with your traction control system See Traction Control System Warning Light in the Index When this warning light is on the system will not limit wheel spin Adjust your driving accordingly The traction control system automatically comes on whenever you start your vehicle To limit wheel spin especially in slippery road conditions you should always leave the system on But you can turn the traction control system off if you ever need to You should turn the system off if your vehicle ever gets stuck in sand mud ice or snow See Rocking Your Vehicle in the Index 4 10 To turn the system off press the TC button on the center console The traction control system warning light will come on and stay on If the system is limiting wheel spin when you press the button the warning light will come on but the system won t turn off right away It will wait until there s no longer a current need to limit wheel spin You can turn the system back
43. few seconds when you turn the ignition key to RUN to let you know it is working Fuel Gage United States Canada When the ignition is on your fuel gage tells you about how much fuel you have left When you have less than 3 0 gallons 11 3 L of fuel remaining the DIC message LOW FUEL will be displayed and a chime will sound You need to get more fuel right away Here are four things that some owners ask about None of these show a problem with your fuel gage At the service station the gas pump shuts off before the gage reads full It takes a little more or less fuel to fill up than the gage indicated For example the gage may have indicated the tank was half full but it actually took a little more or less than half the tank s capacity to fill the tank The gage moves a little when you turn a corner or speed up The tank is not necessarily empty when the gage reads empty There is a reserve of about 1 5 gallons 5 6 L in the tank You should still get more fuel as soon as possible 2 77 Driver Information Center DIC The Driver Information Center DIC displays information in either English or metric When the system is on or off push the ON OFF button down for three seconds to change the display between English and metric This will also change the digital screen for the climate control system between English and metric 2 78 The DIC has different display modes which can be accessed by
44. for an adult or larger child passenger 1 49 Securing a Child Restraint in the Center Rear Seat Position Lap Only Belt y 7 If the center rear seating position has a lap only belt with no retractor follow these instructions to secure a child restraint in the center rear seat If the center rear seating position has a lap shoulder belt with a retractor see the part called Securing a Child Restraint in a Rear Outside Seat Position and in the Center Rear Seat Position Lap Shoulder Belt for instructions on how to secure a child restraint You ll be using the lap belt Be sure to follow the instructions that came with the child restraint Secure the child in the child restraint when and as the instructions say See the earlier part about the top strap if the child restraint has one 1 50 Make the belt as long as possible by tilting the latch plate and pulling it along the belt 2 Put the restraint on the seat 3 Run the vehicle s safety belt through or around the restraint The child restraint instructions will show you how 4 Buckle the belt Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to 5 To tighten the belt pull its free end while you push down on the child restraint If you re using a forward facing child restraint you may find it helpful to use your knee to push down on the child restraint as you tig
45. for replacement 6 56 NOTICE The wrong wheel can also cause problems with bearing life brake cooling speedometer or odometer calibration headlamp aim bumper height vehicle ground clearance and tire or tire chain clearance to the body and chassis See Changing a Flat Tire in the Index for more information Used Replacement Wheels Putting a used wheel on your vehicle is dangerous You can t know how it s been used or how far it s been driven It could fail suddenly and cause an accident If you have to replace a wheel use a new GM original equipment wheel Tire Chains NOTICE If your vehicle has P235 55R17 size tires don t use tire chains They can damage your vehicle because there s not enough clearance Use another type of traction device only if its manufacturer recommends it for use on your vehicle and tire size combination and road conditions Follow that manufacturer s instructions To help avoid damage to your vehicle drive slowly readjust or remove the device if it s contacting your vehicle and don t spin your wheels NOTICE Continued NOTICE Continued If you do find traction devices that will fit install them on the front tires If you have other tires use tire chains only where legal and only when you must Use only SAE Class S type chains that are the proper size for your tires Install them on the front tires and tighten them as tightly as
46. hand your vehicle is in PARK P brake pedal with your left foot 2 Move the shift lever into PARK P by pushing the lever all the way forward 2 30 Leaving Your Vehicle With the Engine Running It can be dangerous to leave your vehicle with the engine running Your vehicle could move suddenly if the shift lever is not fully in PARK P with the parking brake firmly set And if you leave the vehicle with the engine running it could overheat and even catch fire You or others could be injured Don t leave your vehicle with the engine running unless you have to If you have to leave your vehicle with the engine running be sure your vehicle is in PARK P and your parking brake is firmly set before you leave it After you ve moved the shift lever into PARK P hold the regular brake pedal down Then see if you can move the shift lever away from PARK P If you can it means the shift lever wasn t fully locked into PARK P Torque Lock If you are parking on a hill and you don t shift your transaxle into PARK P properly the weight of the vehicle may put too much force on the parking pawl in the transaxle You may find it difficult to pull the shift lever out of PARK P This is called torque lock To prevent torque lock set the parking brake and then shift into PARK P properly before you leave the driver s seat To find out how see Shifting Into PARK P in the Index When you are rea
47. has a visual optical headlamp aiming system equipped with horizontal aim indicators The aim has been pre set at the factory and should need no further adjustment This is true even though your horizontal aim indicators may not fall exactly on the 0 zero marks on their scales If your vehicle is damaged in an accident the headlamp aim may be affected Aim adjustment to the low beam may be necessary if it is difficult to see lane markers for horizontal aim or if oncoming drivers flash their high beams at you for vertical aim If you believe your headlamps need to be re aimed we recommend that you take your vehicle to your dealer for service However it is possible for you to re aim your headlamps as described in the following procedure NOTICE To make sure your headlamps are aimed properly read all the instructions before beginning Failure to follow these instructions could cause damage to headlamp parts 6 40 The vehicle should be properly prepared as follows The vehicle should be placed so the headlamps are 25 ft 7 6 m from a light colored wall or other flat surface The vehicle must have all four tires on a perfectly level surface which is level all the way to the wall or other flat surface The vehicle should be placed so it is perpendicular to the wall or other flat surface The vehicle should not have any snow ice or mud attached to it The vehicle should be fully assembled and al
48. if you have air bags Wearing your safety belt during a crash helps reduce your chance of hitting things inside the vehicle or being ejected from it Air bags are supplemental restraints to the safety belts All air bags are designed to work with safety belts but don t replace them CAUTION Continued 1 22 Frontal air bags for the driver and right front passenger are designed to work only in moderate to severe crashes where the front of your vehicle hits something They aren t designed to inflate at all in rollover rear side or low speed frontal crashes And for unrestrained occupants frontal air bags may provide less protection in frontal crashes than more forceful air bags have provided in the past The side impact air bags for the driver and right front passenger are designed to inflate only in moderate to severe crashes where something hits the side of your vehicle They aren t designed to inflate in frontal in rollover or in rear crashes Everyone in your vehicle should wear a safety belt properly whether or not there s an air bag for that person belt system nor its air bag system is designed Both frontal and side impact air bags inflate for them Young children and infants need the with great force faster than the blink of an eye protection that a child restraint system can If you re too close to an inflating air bag as you provide Always secure children properly in your would be if you w
49. is to slow down when it is raining Driving Through Deep Standing Water NOTICE If you drive too quickly through deep puddles or standing water water can come in through your engine s air intake and badly damage your engine Never drive through water that is slightly lower than the underbody of your vehicle If you can t avoid deep puddles or standing water drive through them very slowly Driving Through Flowing Water Flowing or rushing water creates strong forces If you try to drive through flowing water as you might at a low water crossing your vehicle can be carried away As little as six inches of flowing water can carry away a smaller vehicle If this happens you and other vehicle occupants could drown Don t ignore police warning signs and otherwise be very cautious about trying to drive through flowing water Some Other Rainy Weather Tips Besides slowing down allow some extra following distance And be especially careful when you pass another vehicle Allow yourself more clear room ahead and be prepared to have your view restricted by road spray Have good tires with proper tread depth See Tires in the Index 4 19 City Driving Here are ways to increase your safety in city driving Know the best way to get to where you are going Get a city map and plan your trip into an unknown part of the city just as you would for a cross country trip Try to use the freeways that rim
50. it could be flooded with too much gasoline 1 Without pushing the accelerator pedal turn your Try pushing your accelerator pedal all the way to ignition key to START When the engine starts let the floor and holding it there as you hold the key go of the key The idle speed will go down as your in START for about three seconds If the vehicle engme gets warni starts briefly but then stops again do the same thing but this time keep the pedal down for five or six seconds This clears the extra gasoline from the NOTICE engine After waiting about 15 seconds repeat the normal starting procedure Holding your key in START for longer than 15 seconds at a time will cause your battery to NOTICE be drained much sooner And the excessive heat can damage your starter motor Wait about 15 seconds between each try to help avoid draining your battery or damaging your starter Your engine is designed to work with the electronics in your vehicle If you add electrical parts or accessories you could change the way the engine operates Before adding electrical 2 If it doesn t start right away hold your key in START for about 10 seconds at a time until your equipment check with your dealer If you don t engine starts Wait about 15 seconds between each your engine might not perform properly try to help avoid draining your battery or damaging If you ever have to have your vehicle towed your starter see the part of this ma
51. its job In a crash you could go into it receiving neck or other injuries The lap belt can t do its job either In a crash the belt could go up over your abdomen The belt forces would be there not at your pelvic bones This could cause serious internal injuries For proper protection when the vehicle is in motion have the seatback upright Then sit well back in the seat and wear your safety belt properly Head Restraints Slide the head restraint up or down so that the top of the restraint is closest to the top of your ears This position reduces the chance of a neck injury in a crash Safety Belts They re for Everyone This part of the manual tells you how to use safety belts properly It also tells you some things you should not do with safety belts And it explains the air bag system Don t let anyone ride where he or she can t wear a safety belt properly If you are in a crash and you re not wearing a safety belt your injuries can be much worse You can hit things inside the vehicle or be ejected from it You can be seriously injured or killed In the same crash you might not be if you are buckled up Always fasten your safety belt and check that your passengers belts are fastened properly too It is extremely dangerous to ride in a cargo area inside or outside of a vehicle In a collision people riding in these areas are more likely to be seriously injured or killed Do not allow people t
52. kPa How to Check Use a good quality pocket type gage to check tire pressure You can t tell if your tires are properly inflated simply by looking at them Radial tires may look properly inflated even when they re underinflated Be sure to put the valve caps back on the valve stems They help prevent leaks by keeping out dirt and moisture 6 49 Check Tire Pressure System The check tire pressure system can alert you to a large change in the pressure of one tire The system won t alert you before you drive that a tire is low or flat You must begin driving before the system will work properly The LOW TIRE PRESSURE message will appear on the Driver Information Center DIC if pressure difference low pressure is detected in one tire The check tire pressure system may not alert you if more than one tire is low the vehicle is moving faster than 65 mph 105 km h the system is not yet calibrated e e e the tire treadwear is uneven the compact spare tire is installed tire chains are being used or the vehicle is being driven on a rough or frozen road If the anti lock brake system warning light comes on the check tire pressure system may not be working properly See your dealer for service Also see Anti Lock Brake System Warning Light in the Index 6 50 The check tire pressure system detects differences in tire rotation speeds that are caused by changes in tire pressure The syste
53. key or by turning the ignition on Personalization Features The following list of features available on your vehicle can be programmed to the driver s preference for each transmitter Automatic Door Locks This feature programs your door locks to automatically lock or unlock when shifting in and out of PARK P or when the key is turned to LOCK Security Feedback This feature provides feedback to the driver when the vehicle receives a command from the remote lock control transmitter Delayed Locking This feature lets the driver delay the actual locking of the vehicle When all doors have been closed the doors will lock automatically after five seconds Perimeter Lighting When the unlock symbol on the remote lock control transmitter is pressed the Daytime Running Lamps DRL parking lamps and back up lamps will turn on if it is dark enough outside For more detailed information and programming instructions for each feature mentioned refer to the Index 2 11 Security Feedback This feature provides feedback to the driver when the vehicle receives a command from the remote lock control transmitter and all doors are closed The following settings can be programmed for each of the remote lock control transmitters No feedback when locking or unlocking vehicle Parking lamps and the Daytime Running Lamps will flash twice when unlocking the vehicle and flash once when locking the vehicle Horn chirps when
54. leak means that sooner or later your brakes won t work well or won t work at all 6 32 So it isn t a good idea to top off your brake fluid Adding brake fluid won t correct a leak If you add fluid when your linings are worn then you ll have too much fluid when you get new brake linings You should add or remove brake fluid as necessary only when work is done on the brake hydraulic system If you have too much brake fluid it can spill on the engine The fluid will burn if the engine is hot enough You or others could be burned and your vehicle could be damaged Add brake fluid only when work is done on the brake hydraulic system When your brake fluid falls to a low level your brake warning light will come on A chime will sound if you try to drive with this warning light on See Brake System Warning Light in the Index What to Add When you do need brake fluid use only DOT 3 brake fluid Use new brake fluid from a sealed container only Refer to Recommended Fluids and Lubricants in the Maintenance Schedule Always clean the brake fluid reservoir cap and the area around the cap before removing it This will help keep dirt from entering the reservoir With the wrong kind of fluid in your brake system your brakes may not work well or they may not even work at all This could cause a crash Always use the proper brake fluid NOTICE Using the wrong fluid can badly damage
55. limit for cold tires You ll find these numbers on the Tire Loading Information label at the rear edge of the driver s door or see Loading Your Vehicle in the Index Then be sure you don t go over the GVW limit for your vehicle including the weight of the trailer tongue Hitches It s important to have the correct hitch equipment Crosswinds large trucks going by and rough roads are a few reasons why you ll need the right hitch Here are some rules to follow The rear bumper on your vehicle is not intended for hitches Do not attach rental hitches or other bumper type hitches to it Use only a frame mounted hitch that does not attach to the bumper Will you have to make any holes in the body of your vehicle when you install a trailer hitch If you do then be sure to seal the holes later when you remove the hitch If you don t seal them deadly carbon monoxide CO from your exhaust can get into your vehicle See Carbon Monoxide in the Index Dirt and water can too 4 34 Safety Chains You should always attach chains between your vehicle and your trailer Cross the safety chains under the tongue of the trailer so that the tongue will not drop to the road if it becomes separated from the hitch Instructions about safety chains may be provided by the hitch manufacturer or by the trailer manufacturer Follow the manufacturer s recommendation for attaching safety chains and do not attach them to the bump
56. may not clean as thoroughly as the scrubbing type cleaner The use of a non scrubbing action dry type cleaning cassette is not recommended After you clean the player press and hold EJECT for five seconds to reset the CLEAN PLAYR indicator The radio will display CLEANED to show the indicator was reset Cassettes are subject to wear and the sound quality may degrade over time Always make sure the cassette tape is in good condition before you have your tape player serviced Care of Your Compact Discs Handle discs carefully Store them in their original cases or other protective cases and away from direct sunlight and dust If the surface of a disc is soiled dampen a clean soft cloth in a mild neutral detergent solution and clean it wiping from the center to the edge Be sure never to touch the signal surface when handling discs Pick up discs by grasping the outer edges or the edge of the hole and the outer edge Care of Your Compact Disc Player The use of CD lens cleaner discs is not advised due to the risk of contaminating the lens of the CD optics with lubricants internal to the CD mechanism Diversity Antenna System Your AM FM antennas are located in the front windshield and rear window Be sure that the inside surfaces of the front windshield and rear window are not scratched and that the lines on the glass are not damaged If the inside surfaces are damaged they could interfere with radio reception Also for pro
57. need to check your engine oil level right away For more information see DIC Warnings and Messages in the Index You should check your engine oil level regularly this is an added reminder Checking Engine Oil It s a good idea to check your engine oil every time you get fuel In order to get an accurate reading the oil must be warm and the vehicle must be on level ground The top of the engine oil dipstick is a round yellow loop See Engine Compartment Overview in the Index for more information on location Turn off the engine and give the oil several minutes to drain back into the oil pan If you don t the oil dipstick might not show the actual level 6 15 Pull out the dipstick and clean it with a paper towel or When to Add Engine Oil cloth then push it back in all the way Remove it again keeping the tip down and check the level If the oil is at or below the ADD line then you ll need to add at least one quart of oil But you must use the right kind This part explains what kind of oil to use For crankcase capacity see Capacities and Specifications in the Index NOTICE Don t add too much oil If your engine has so 3 5L V6 Engine much oil that the oil level gets above the upper mark that shows the proper operating range your engine could be damaged 4 0L V8 Engine 6 16 See Engine Compartment Overview in the Index for more information on location Be sure
58. occur at speeds of less than 40 mph 65 km h Safety belts are for everyone How to Wear Safety Belts Properly Adults This part is only for people of adult size Be aware that there are special things to know about safety belts and children And there are different rules for smaller children and babies If a child will be riding in your vehicle see the part of this manual called Children Follow those rules for everyone s protection First you ll want to know which restraint systems your vehicle has We ll start with the driver position 1 13 Driver Position This part describes the driver s restraint system Lap Shoulder Belt The driver has a lap shoulder belt Here s how to wear it properly 1 Close and lock the door 2 Adjust the seat so you can sit up straight To see how see Seats in the Index 1 14 3 Pick up the latch plate and pull the belt across you Don t let it get twisted The lap shoulder belt may lock if you pull the belt across you very quickly If this happens let the belt go back slightly to unlock it Then pull the belt across you more slowly 4 Push the latch plate into the buckle until it clicks The lap part of the belt should be worn low and snug on the hips just touching the thighs In a crash this applies force to the strong pelvic bones And you d be less likely to slide under the lap belt If you slid under it the belt would apply force at yo
59. of the dipstick and read the lower level The fluid level must be in the cross hatched area a 3 After adding fluid recheck the fluid level as 4 If the fluid level is in the acceptable range push the described under How to Check ey 4 When the correct fluid level is obtained push the dipstick back in all the way 6 25 Engine Coolant The cooling system in your vehicle is filled with DEX COOL engine coolant This coolant is designed to remain in your vehicle for 5 years or 150 000 miles 240 000 km whichever occurs first if you add only DEX COOL extended life coolant The following explains your cooling system and how to add coolant when it is low If you have a problem with engine overheating see Engine Overheating in the Index A 50 50 mixture of clean drinkable water and DEX COOL coolant will Give freezing protection down to 34 F 37 C Give boiling protection up to 265 F 129 C Protect against rust and corrosion Help keep the proper engine temperature Let the warning lights and gages work as they should 6 26 NOTICE When adding coolant it is important that you use only DEX COOL silicate free coolant If coolant other than DEX COOL is added to the system premature engine heater core or radiator corrosion may result In addition the engine coolant will require change sooner at 30 000 miles 50 000 km or 24 months whichever occurs first D
60. on at any time by pressing the button again The traction control system warning light should go off Steering Power Steering If you lose power steering assist because the engine stops or the system is not functioning you can steer but it will take much more effort Magnetic Speed Variable Assist Steering Your vehicle is equipped with a steering system that continuously adjusts the effort you feel when steering at all vehicle speeds It provides ease when parking yet a firm solid feel at highway speeds Steering Tips Driving on Curves It s important to take curves at a reasonable speed A lot of the driver lost control accidents mentioned on the news happen on curves Here s why Experienced driver or beginner each of us is subject to the same laws of physics when driving on curves The traction of the tires against the road surface makes it possible for the vehicle to change its path when you turn the front wheels If there s no traction inertia will keep the vehicle going in the same direction If you ve ever tried to steer a vehicle on wet ice you ll understand this The traction you can get in a curve depends on the condition of your tires and the road surface the angle at which the curve is banked and your speed While you re in a curve speed is the one factor you can control Suppose you re steering through a sharp curve Then you suddenly accelerate Both control systems steering and
61. or inactive through the DIC When TILT MIRROR REVERSE appears on the display use the SELECT right arrow button to toggle the arrow between YES and NO When you have made your choice press the SELECT down arrow button to record your selection For more information on this feature see Mirrors in the Index 2 89 DIC Warnings and Messages Other messages or warnings may appear in the DIC display For Canadian drivers in addition to the DIC message your DIC will display EXP with a number after it which reflects the following messages EXP Export ID Warning Message Lge wne cadens ae gether os AIR BAG PROBLEM Di taeb Dea Re rn rires RA CHANGE OIL NOW Boi tnghstue nace ee tees CHANGE OIL SOON A ee beta ee aes CHECK CHARGE SYSTEM Settee eaor abe at ar hes CHECK OIL LEVEL EE ee ebh bane TRANS HOT IDLE ENG Tbs Sate bebe os Hee ees CONFIRM TIME amp DATE ee DRIVERS DOOR AJAR Dida hater bet teats ENGINE HOT A C OFF TOs badd eee ban HOT REDUCE ENG RPM TD che hata os eee wunaies HOT STOP ENGINE lD ace he ictor ae bane THEFT SYSTEM FAULT 13 sede Paedbedaie ees LEFT REAR DOOR AJAR e eb eae bh bas LOW BRAKE FLUID VD este baba oe se ens LOW ENGINE COOLANT lO ahi Er E bac LOW FUEL 2 90 ET hairy Se cat wears seik LOW OIL PRESSURE IS E bade ee sae LOW TIRE PRESSURE 1 gies bare heeeee aes LOW WASHER FLUID QO tee cae se wee ks ae 9 PARK BRAKE SET 2l fe oh meas beani WS PASSENGER DOOR AJAR DD oie aig ske
62. out Glare at night is made much worse by dirt on the glass Even the inside of the glass can build up a film caused by dust Dirty glass makes lights dazzle and flash more than clean glass would making the pupils of your eyes contract repeatedly Remember that your headlamps light up far less of a roadway when you are in a turn or curve Keep your eyes moving that way it s easier to pick out dimly lighted objects Just as your headlamps should be checked regularly for proper aim so should your eyes be examined regularly Some drivers suffer from night blindness the inability to see in dim light and aren t even aware of it Driving in Rain and on Wet Roads Rain and wet roads can mean driving trouble On a wet road you can t stop accelerate or turn as well because your tire to road traction isn t as good as on dry roads And if your tires don t have much tread left you ll get even less traction It s always wise to go slower and be cautious if rain starts to fall while you are driving The surface may get wet suddenly when your reflexes are tuned for driving on dry pavement 4 17 The heavier the rain the harder it is to see Even if your windshield wiper blades are in good shape a heavy rain can make it harder to see road signs and traffic signals pavement markings the edge of the road and even people walking It s wise to keep your windshield wiping equipment in good shape and keep your windshield
63. out of PARK P All doors automatically unlock when the key is turned to LOCK You can change which mode your vehicle is in by different selections of the following DIC displays DOORS LOCK IN GEAR YES NO DOORS UNLOCK YES NO ALL DOORS IN PARK YES NO ALL DOORS AT KEY OFF YES NO DRIVERS DOOR IN PARK YES NO DRIVERS DOOR KEY OFF YES NO 2 85 Press the SELECT right arrow button to toggle between your choices and change the settings Press the SELECT down arrow button to store your changes in memory and move on to the next selection If you would like to program your vehicle to Mode 0 select NO for DOORS LOCK IN GEAR Your door locks will operate normally with no automatic feature If you would like to program your vehicle to Mode 1 do the following 1 Select YES for DOORS LOCK IN GEAR 2 Select NO for DOORS UNLOCK If you would like to program your vehicle to Mode 2 do the following 1 Select YES for DOORS LOCK IN GEAR 2 Select YES for DOORS UNLOCK 3 Select NO for ALL DOORS IN PARK 4 Select NO for ALL DOORS AT KEY OFF 5 Select YES for DRIVERS DOOR IN PARK 2 86 If you would like to program your vehicle to Mode 3 do the following 1 Select YES for DOORS LOCK IN GEAR 2 Select YES for DOORS UNLOCK 3 Select YES for ALL DOORS IN PARK If you would like to program your vehicle to Mode 4 do the following 1 Select YES for DOORS LOCK IN GEAR Select YES for DOORS UNLOCK Select NO
64. out and close the door Remote Lock Control You can lock and unlock your doors or unlock your trunk from about 3 feet 1 m up to 30 feet 9 m away using the remote lock control transmitter supplied with your vehicle Your remote lock control operates on a radio frequency subject to Federal Communications Commission FCC Rules and with Industry Canada This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This device complies with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference received including interference that may cause undesired operation of the device Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment At times you may notice a decrease in range This is normal for any remote keyless entry system If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work try this Check the distance You may be too far from your vehicle You may need to stand closer during rainy or snowy weather Check the location Other vehicles or objects may be blocki
65. pressing the four buttons on the DIC These buttons are labeled ON OFF SELECT right arrow SELECT down arrow and RESET The button functions are detailed in the following Turn on the system by pressing the ON OFF button once When you turn on the ignition the DIC will be in the mode last displayed when the engine was turned off Keep in mind that this also applies to the OFF mode To turn off messages on the DIC except LOW OIL PRESSURE LOW BRAKE FLUID PARK BRAKE SET STARTING DISABLED and the HOT STOP ENGINE warning press the RESET button Pressing the SELECT right arrow button will allow you to access the following modes DATE ET FUEL ECON OIL and GAGE While in any of these modes warning messages can interrupt and take over the display until you acknowledge the message or the condition causing the problem goes away Date Elapsed Time Pressing the SELECT down arrow while in DATE ET mode will allow you to choose between the elapsed time and date menus Date To set the date press and hold the RESET button for two seconds while the date is being displayed on the DIC When the date set mode is entered the display will show the following YEAR MM DD 00 The year will be flashing To increase the item that is flashing press SELECT right arrow To decrease the item that is flashing press SELECT down arrow When you reach the current year press the RESET button The DIC will ask for the month The month will flas
66. pull the belt very quickly out of the retractor You can be seriously hurt if your shoulder belt is too loose In a crash you would move forward too much which could increase injury The shoulder belt should fit against your body To unlatch the belt just push the button on the buckle 1 33 Rear Safety Belt Comfort Guides for Children and Small Adults Rear shoulder belt comfort guides will provide added safety belt comfort for older children who have outgrown booster seats and for small adults When installed on a shoulder belt the comfort guide better positions the belt away from the neck and head There is one guide for each outside passenger position in the rear seat To provide added safety belt comfort for children who have outgrown child restraints and for smaller adults the comfort guides may be installed on the shoulder belts Here s how to install a comfort guide and use the safety belt 1 34 1 Remove the guide from its storage pocket on the side of the seatback 2 Slide the guide under and past the belt The elastic 3 Be sure that the belt is not twisted and it lies flat cord must be under the belt Then place the guide The elastic cord must be under the belt and the guide over the belt and insert the two edges of the belt into on top the slots of the guide 1 35 4 Buckle position and release the safety belt as described in Rear Seat Passenger Positions earlier in this section
67. reset Oil Life The GM Oil Life System is the only function accessible in the OIL mode Engine oil life is displayed in a reading such as OIL LIFE 30 This is an estimate of the oil s remaining useful life It will show 100 when the system is reset after an oil change It will alert you to change your oil on a schedule consistent with your driving conditions When the remaining oil life is low the system will alert you with this message CHANGE OIL SOON When the oil life is down to zero you will receive this message CHANGE OIL NOW Always reset the OIL LIFE reminder after an oil change To reset the Oil Life System see Oil Life System in the Index Also see Engine Oil When to Change in the Index Remember you must reset the OIL LIFE yourself after each oil change It will not reset itself Also be careful not to reset the OIL LIFE accidentally at any time other than when the oil has just been changed It can t be reset accurately until the next oil change The DIC does not replace the need to maintain your vehicle as recommended in the Maintenance Schedule in this manual Also the oil change reminder will not detect dusty conditions or engine malfunctions that may affect the oil If you drive in dusty areas change your oil after every 3 000 miles 5 000 km or three months whichever occurs first unless the DIC instructs you to do so sooner Also the oil change reminder does not measure
68. rounding throughout the pregnancy The best way to protect the fetus is to protect the mother When a safety belt is worn properly it s more likely that the fetus won t be hurt in a crash For pregnant women as for anyone the key to making safety belts effective is wearing them properly Right Front Passenger Position To learn how to wear the right front passenger s safety belt properly see Driver Position earlier in this section The right front passenger s safety belt works the same way as the driver s safety belt except for one thing If you ever pull the lap portion of the belt out all the way you will engage the child restraint locking feature If this happens just let the belt go back all the way and start again Air Bag Systems This part explains the frontal and side impact air bag systems Your vehicle has four air bags a frontal air bag for the driver another frontal air bag for the right front passenger a side impact air bag for the driver and another side impact air bag for the right front passenger Frontal air bags are designed to help reduce the risk of injury from the force of an inflating frontal air bag But these air bags must inflate very quickly to do their job and comply with federal regulations 1 21 Here are the most important things to know about the air bag systems You can be severely injured or killed in a crash if you aren t wearing your safety belt even
69. s an emergency a need to take sudden action as when a child darts into the street A person with even a moderate BAC might not be able to react quickly enough to avoid the collision There s something else about drinking and driving that many people don t know Medical research shows that alcohol in a person s system can make crash injuries worse especially injuries to the brain spinal cord or heart This means that when anyone who has been drinking driver or passenger is in a crash that person s chance of being killed or permanently disabled is higher than if the person had not been drinking Drinking and then driving is very dangerous Your reflexes perceptions attentiveness and judgment can be affected by even a small amount of alcohol You can have a serious or even fatal collision if you drive after drinking Please don t drink and drive or ride with a driver who has been drinking Ride home in a cab or if you re with a group designate a driver who will not drink Control of a Vehicle You have three systems that make your vehicle go where you want it to go They are the brakes the steering and the accelerator All three systems have to do their work at the places where the tires meet the road Sometimes as when you re driving on snow or ice it s easy to ask more of those control systems than the tires and road can provide That means you can lose control of your vehicle Also see
70. seconds after the ignition key is turned off and the battery is disconnected an air bag can still inflate during improper service You can be injured if you are close to an air bag when it inflates Avoid yellow connectors They are probably part of the air bag systems Be sure to follow proper service procedures and make sure the person performing work for you is qualified to do so The air bag systems do not need regular maintenance 1 29 Rear Seat Passengers It s very important for rear seat passengers to buckle up Accident statistics show that unbelted people in the rear seat are hurt more often in crashes than those who are wearing safety belts Rear passengers who aren t safety belted can be thrown out of the vehicle in a crash And they can strike others in the vehicle who are wearing safety belts 1 30 Rear Seat Passenger Positions ak e e D Lap Shoulder Belt The positions next to the windows have lap shoulder belts Here s how to wear one properly The center rear position may also have a lap shoulder belt with a retractor If it does this part will tell you how to use the center seat lap shoulder belt properly If the center rear position has a lap belt only with no retractor see the part of this manual called Center Passenger Position for instructions on how to properly wear the lap only belt 1 Pick up the latch plate and pull the belt across you Don t let it get twisted
71. starts Wait about 15 seconds between each Your Vehicle in the Index try to help avoid draining your battery or damaging your starter 2 24 Engine Coolant Heater If Equipped In very cold weather 0 F 18 C or colder the engine coolant heater can help You ll get easier starting and better fuel economy during engine warm up Usually the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle To Use the Engine Coolant Heater 1 Turn off the engine 2 Open the hood and unwrap the electrical cord The engine coolant heater cord is located on the passenger s side of the vehicle above the headlamp assembly 3 Plug it into a normal grounded 110 volt AC outlet Plugging the cord into an ungrounded outlet could cause an electrical shock Also the wrong kind of extension cord could overheat and cause a fire You could be seriously injured Plug the cord into a properly grounded three prong 110 volt AC outlet If the cord won t reach use a heavy duty three prong extension cord rated for at least 15 amps 4 Before starting the engine be sure to unplug and store the cord as it was before to keep it away from moving engine parts If you don t it could be damaged How long should you keep the coolant heater plugged in The answer depends on the outside temperature the kind of oil you have and some other things Instead of trying to list everything here we ask that y
72. that a woman generally will reach a higher BAC level than a man of her same body weight when each has the same number of drinks The law in many U S states sets the legal limit at a BAC of 0 10 percent In a growing number of U S states and throughout Canada the limit is 0 08 percent In some other countries it s even lower The BAC limit for all commercial drivers in the United States is 0 04 percent The BAC will be over 0 10 percent after three to six drinks in one hour Of course as we ve seen it depends on how much alcohol is in the drinks and how quickly the person drinks them But the ability to drive is affected well below a BAC of 0 10 percent Research shows that the driving skills of many people are impaired at a BAC approaching 0 05 percent and that the effects are worse at night All drivers are impaired at BAC levels above 0 05 percent Statistics show that the chance of being in a collision increases sharply for drivers who have a BAC of 0 05 percent or above A driver with a BAC level of 0 06 percent has doubled his or her chance of having a collision At a BAC level of 0 10 percent the chance of this driver having a collision is 12 times greater at a level of 0 15 percent the chance is 25 times greater The body takes about an hour to rid itself of the alcohol in one drink No amount of coffee or number of cold showers will speed that up Ill be careful isn t the right answer What if there
73. the windows while the ignition is on or retained accessory power RAP is active In addition each passenger s door armrest has a window switch for its own window Express Down Windows The driver s and right front passenger s windows have an express down feature When either window switch is pressed all the way rearward and then released the window will lower completely The window can be opened in smaller amounts by pressing the switch rearward slightly to the first stop To stop the window while it is lowering in the express mode press the switch again then release To raise the window hold the switch forward Window Lock Press the LOCK button on the driver s door armrest to lock out all passenger window controls Through the Driver Information Center DIC you can also set the control to only lock out the rear window controls See Driver Information Center in the Index The driver s window switches will still be operable This is a useful feature when you have children as passengers Press the LOCK button again to allow passengers to use their window controls Keys Leaving children in a vehicle with the ignition key is dangerous for many reasons A child or others could be badly injured or even killed They could operate the power windows or other controls or even make the vehicle move Don t leave the keys in a vehicle with children The master key works in all of the lock cylinders doo
74. the battery To replace the battery NOTICE 1 Insert a coin into the notch near the key ring Turn the coin counterclockwise to separate the two halves When replacing the battery use care not to of the transmitter touch any of the circuitry Static from your 2 body transferred to these surfaces may damage the transmitter Once the transmitter is separated use a pencil eraser to remove the old battery Do not use a metal object 3 Replace the battery as the instructions under the cover indicate 4 Snap the transmitter back together tightly to be sure no moisture can enter 5 Test the operation of the transmitter with your vehicle If the transmitter does not work resynchronize the transmitter For battery replacement use a Duracell battery type DL 2032 or a similar type 2 13 Resynchronization Pressing the transmitter buttons numerous times approximately 250 times out of the vehicle s operating range may cause the transmitter not to work Replacing the battery and pressing the transmitter buttons out of range will also cause the transmitter not to work If only the instant alarm works the transmitter needs to be resynchronized to the receiver Resynchronize by pressing and holding both the buttons with the lock and unlock symbols at the same time for about eight seconds You must be within range of the vehicle Once the transmitter has been resynchronized the locks will cycle the horn may ch
75. the cruise control will automatically disengage See Traction Control System in the Index When road conditions allow you to safely use it again you may turn the cruise control back on Setting Cruise Control If you leave your cruise control switch on when you re not using cruise you might hit a button and go into cruise when you don t want to You could be startled and even lose control Keep the cruise control switch off until you want to use cruise control 2 42 Push the cruise control switch located at the end of the lever in to ON Get up to the speed you want 3 Push the lever down to SET CST and release it The CRUISE light on the instrument panel cluster will come on Take your foot off the accelerator pedal Resuming a Set Speed Setting the cruise control at a desired speed and then applying the brake will end the cruise control function Once you re going about 25 mph 40 km h or more you can briefly push the cruise control lever up to RES ACC Resume Accelerate to reset This returns you to your desired preset speed Remember if you hold the lever up at RES ACC the vehicle will accelerate until you release the lever or apply the brake So unless you want to go faster don t hold the lever at RES ACC Increasing Speed While Using Cruise Control There are three ways to go to a higher speed Use the accelerator pedal to go to a higher speed Push the lever down then r
76. the tuned radio station or a related network station you will hear it even if the volume is muted or a cassette tape or compact disc is playing If the cassette tape or compact disc player was being used the tape or compact disc will stay in the player and resume play at the point where it stopped 3 13 INFO If the current station has a message INFO will appear on the display Press this button to see the message If the whole message does not appear on the display parts of the message will appear every three seconds until the message is completed To see the parts of the message faster than every three seconds press this button again A new group of words will appear on the display Once the complete message has been displayed INFO will disappear from the display until another new message is received P TYPE This button is used to turn on and off Program Type PTY select The PTY icon and the light next to the button will turn on The last selected PTY will appear on the display for five seconds Turn the P TYPE knob to select the PTY you want to listen to Press SEEK or SCAN to find radio stations of the PTY you want to listen to The last PTY selected will be used for seek or scan modes If a station with the selected PTY is not found NONE FOUND will appear on the display If both P TYPE and TRAF are on the radio will search for stations with traffic announcements and the selected PTY 3 14 To use the P TYPE interrupt
77. to be turned off Then you will not have automatic door lock or unlock This feature will function when you close the doors and turn on the ignition If someone needs to get out while you re not in PARK P have that person use the manual or power door lock When the door is closed again it will not lock automatically Use the manual or power lock to lock the door again 2 7 You must program this feature through the Driver Information Center DIC See DIC Personalization Programming in the Index Overriding Lock Delay If you need to lock your doors before shifting out of PARK P use the manual or power door lock switch to lock the doors Delayed Locking This personalization feature lets the driver delay the actual locking of the vehicle When the driver s power door lock switch or the lock symbol on the remote lock control is pressed with the key removed from the ignition and the driver s door open a chime will sound three times to signal that the lock delay mode is active When all doors have been closed the doors will lock automatically after five seconds If any door is opened before this the five second timer will reset itself once all the doors have been closed again Pressing the driver s or passenger s door lock switch or the lock symbol on the remote lock control a second time will override this feature You must program this feature through the Driver Information Center DIC See DIC Perso
78. to you Fuel delivery Lock out service identification required Tow to the nearest dealership for warranty service or in the event of a vehicle disabling accident e Fiat tire change Jump starts Minor repairs to disabled vehicles Assistance when vehicle is mired in sand mud or snow Trip routing Trip interruption expense benefits Dealership locator service Courtesy Transportation See Courtesy Transportation section for details Oldsmobile Roadside Assistance specifically excludes coverage for mounting dismounting or changing of snow tires chains or other traction devices In some cases where service is impractical the driver may be authorized to obtain other service for which reimbursement is provided In many instances mechanical failures are covered under Oldsmobile s comprehensive warranty However when other services are utilized our Roadside Assistance Representatives will explain any payment obligations you might incur For prompt and efficient assistance when calling please provide the following to the Roadside Assistance Representative Location of vehicle Telephone number of your location Vehicle model year and color Mileage of vehicle Vehicle Identification Number VIN Vehicle license plate number Oldsmobile reserves the right to limit services or reimbursement to an owner or driver when in Oldsmobile s judgement the claims become excessive in fre
79. unconsciousness and death You might have exhaust coming in if Your exhaust system sounds strange or different Your vehicle gets rusty underneath Your vehicle was damaged in a collision Your vehicle was damaged when driving over high points on the road or over road debris Repairs weren t done correctly Your vehicle or exhaust system had been modified improperly If you ever suspect exhaust is coming into your vehicle Drive it only with all the windows down to blow out any CO and Have your vehicle fixed immediately Running Your Engine While You re Parked It s better not to park with the engine running But if you ever have to here are some things to know Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle See the earlier Caution under Engine Exhaust Also idling in a closed in place can let deadly carbon monoxide CO into your vehicle even if the fan switch is at the highest setting One place this can happen is a garage Exhaust with CO can come in easily NEVER park ina garage with the engine running Another closed in place can be a blizzard See Blizzard in the Index 2 33 It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK P with the parking brake firmly set Your vehicle can roll Don t leave your vehicle when the engine is running unless you have to If you ve
80. vehicle with the good battery and run the engine for a while Try to start the vehicle with the dead battery If it won t start after a few tries it probably needs service 13 Remove the cables in reverse order to prevent Towing Your Vehicle electrical shorting Take care that they don t touch each other or any other metal Replace the red positive remote terminal cover to its original position To help avoid serious personal injury to you or others Never let passengers ride in a vehicle that is being towed Never tow faster than safe or posted speeds Never tow with damaged parts not fully secured Never get under your vehicle after it has been lifted by the tow truck Always secure the vehicle on each side with separate safety chains when towing it Use only the correct hooks A Remote Positive Terminal B Good Battery C Heavy Unpainted Metal Engine Part 5 8 NOTICE Use the proper towing equipment to avoid damage to the bumper fascia or fog lamp areas of the vehicle With current trends in automotive styles and design it is essential that the correct towing equipment is used to tow a vehicle Your vehicle can be towed with wheel lift or car carrier equipment only Consult your dealer or a professional towing service if you need to have your vehicle towed See Roadside Assistance in the Index Engine Overheating You will find a coolant temperature gage on your vehicle
81. washer tank filled with washer fluid Replace your windshield wiper inserts when they show signs of streaking or missing areas on the windshield or when strips of rubber start to separate from the inserts 4 18 Driving too fast through large water puddles or even going through some car washes can cause problems too The water may affect your brakes Try to avoid puddles But if you can t try to slow down before you hit them Wet brakes can cause accidents They won t work as well in a quick stop and may cause pulling to one side You could lose control of the vehicle After driving through a large puddle of water or a car wash apply your brake pedal lightly until your brakes work normally Hydroplaning Hydroplaning is dangerous So much water can build up under your tires that they can actually ride on the water This can happen if the road is wet enough and you re going fast enough When your vehicle is hydroplaning it has little or no contact with the road Hydroplaning doesn t happen often But it can if your tires do not have much tread or if the pressure in one or more is low It can happen if a lot of water is standing on the road If you can see reflections from trees telephone poles or other vehicles and raindrops dimple the water s surface there could be hydroplaning Hydroplaning usually happens at higher speeds There just isn t a hard and fast rule about hydroplaning The best advice
82. will burn onto a hot engine Hood Release To open the hood first pull the hood release handle located to the left of the steering wheel under the instrument panel Then go to the front of the vehicle and pull up on the secondary hood release Lift the hood Before closing the hood be sure all the filler caps are on properly Then pull the hood down and close it firmly 6 11 When you open the hood you ll see 7m 0A wD gt Underhood Bussed Electrical Center Windshield Washer Fluid Reservoir Engine Coolant Surge Tank Remote Positive Terminal Heavy Unpainted Metal Engine Part Passenger Compartment Air Filter Et at St ev eG Power Steering Fluid Reservoir Engine Oil Fill Cap Engine Oil Dipstick Automatic Transaxle Fluid Dipstick Brake Fluid Reservoir Engine Air Cleaner Filter 6 13 When you open the hood you ll see A Underhood Bussed E Power Steering Fluid Reservoir J Brake Fluid Reservoir Electrical Center F Passenger Compartment K Automatic Transaxle B Windshield Washer Air Filter Fluid Dipstick Fluid Reservoir G Remote Negative Terminal near the air cleaner C Engine Coolant Surge Tank H Engine Oil Fill Cap L Engine Air Cleaner Filter D Remote Positive I Engine Oil Dipstick Battery Terminal Engine Oil SELECT gt SELECT Y If the CHECK OIL LEVEL message appears on the instrument panel it means you
83. with a computer which monitors operation of the fuel ignition and emission control systems This system is called OBD II On Board Diagnostics Second Generation and is intended to assure that emissions are at acceptable levels for the life of the vehicle helping to produce a cleaner environment The CHECK ENGINE light comes on to indicate that there is a problem and service is required Malfunctions often will be indicated by the system before any problem is apparent This may prevent more serious damage to your vehicle This system is also designed to assist your service technician in correctly diagnosing any malfunction NOTICE If you keep driving your vehicle with this light on after a while your emission controls may not work as well your fuel economy may not be as good and your engine may not run as smoothly This could lead to costly repairs that may not be covered by your warranty NOTICE Modifications made to the engine transaxle exhaust or fuel system of your vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria TPC can affect your vehicle s emission controls and may cause the CHECK ENGINE light to come on Modifications to these systems could lead to costly repairs not covered by your warranty This may also result in a failure to pass a required Emission Inspection Maintenance test 2 73 This light should come on as a check to show you it is w
84. 1 4 Adjust the driver s seat including the lumbar adjustments and both outside mirrors to the position you would like for driving Then press and hold memory button 1 for more than three seconds A double beep will sound when the memory is set To set the seat and mirror positions for a second driver follow the previous steps but press button 2 instead You can also store an exit position for each driver The exit position is programmed by moving the seat to the desired exit position and then holding the exit button for more than three seconds The exit position set will be for the most recently selected driving position 1 or 2 Please note that mirror and lumbar positions will not be stored or recalled for the exit position To recall your memory positions your vehicle must be in PARK P Push and release the memory button 1 or 2 corresponding to the desired driving position The seat and mirrors will move to the position previously stored for the identified driver You will hear one beep To recall the exit position your vehicle must be in PARK P Push and release the EXIT button and the seat will move to the exit position previously stored for the current identified driver You will hear one beep If an exit position has not been stored for the current identified driver the seat will move all the way back To stop recall movement of the seat at any time press one of the power seat controls located on the outboard
85. 1 800 355 3515 Be sure to keep the original hand held transmitter in case you need to erase and reprogram the HomeLink Transmitter Note to Canadian Owners During programming the hand held transmitter may automatically stop transmitting after one or two seconds In this case you should press and repress the button on the hand held transmitter every two seconds without ever releasing the button on the HomeLink Transmitter Release both buttons when the indicator light on the HomeLink Transmitter begins to flash rapidly 2 59 Operating the HomeLink Transmitter Press and release the appropriate button on the HomeLink Transmitter The indicator light comes on while the signal is being transmitted The trunk release lockout switch must be OFF If the hand held transmitter appears to program the HomeLink Transmitter but does not open your garage door and if the garage door opener was manufactured after 1996 the garage door opener may have a rolling code system A rolling code system changes the code of the garage door opener every time you open or close the garage door To determine if you have this system press the button on the HomeLink Transmitter that you have already programmed If the indicator light on the HomeLink Transmitter flashes rapidly for two seconds and then turns solid the garage door opener has a rolling code system In a rolling code system the garage door motor head unit must be trained to the HomeLi
86. 20 Engine Air Cleaner Filter The engine air cleaner and filter are on the driver s side of the engine compartment See Engine Compartment Overview in the Index for more information on location To check or replace the air filter 1 Using a Phillips screwdriver unscrew the two wing screws on the outboard side of the filter cover Remove the cover Remove the air filter Install the new air filter and reverse all of the steps Be sure the tabs of the air cleaner cover fit into the slots of the air cleaner housing Refer to the Maintenance Schedule to determine when to replace the air filter See Scheduled Maintenance Services in the Index Operating the engine with the air cleaner filter off can cause you or others to be burned The air cleaner not only cleans the air it stops flame if the engine backfires If it isn t there and the engine backfires you could be burned Don t drive with it off and be careful working on the engine with the air cleaner filter off NOTICE If the air cleaner filter is off a backfire can cause a damaging engine fire And dirt can easily get into your engine which will damage it Always have the air cleaner filter in place when yov re driving 6 21 Passenger Compartment Air Filter The passenger compartment air filter removes certain particles from the air including pollen and dust particles Reductions in airflow which may occur more often in d
87. 3 12 Setting the Tone BASS Press the AUDIO button until BASS appears on the display Turn the audio knob to increase or decrease bass When you use this control the radio s tone setting will switch to manual MID Press the AUDIO button until MID appears on the display Turn the audio knob to increase or decrease bass When you use this control the radio s tone setting will switch to manual TREB Press the AUDIO button until TREB appears on the display Turn the audio knob to increase or decrease treble When you use this control the radio s tone setting will switch to manual If a station is weak or noisy you may want to decrease the treble Pressing and holding the AUDIO button for at least two seconds will return all tone settings including BALANCE and FADE to FLAT AUTO EQ This feature allows you to choose preset bass mid and treble equalization settings designed for country jazz talk pop rock and classical stations The last setting will appear on the display when you first press AUTO EQ Each time you press AUTO EQ another setting will appear on the display Press AUTO EQ again after TALK appears and MANUAL will appear Tone control will return to the BASS MID and TREB Also if you use BASS MID and TREB the radio s tone setting will switch to manual and MANUAL will appear on the display Using RDS Mode Your audio system is equipped with a Radio Data System RDS RDS mode gives you many useful
88. 39 4 L To learn how much fuel will be used from a specific starting point first enter the FUEL USED mode to display FUEL USED then press and hold the RESET button for three seconds Don t confuse fuel used with the amount of fuel in your tank Fuel Range The FUEL RANGE mode calculates the remaining distance you can drive without refueling It s based on fuel economy and the fuel remaining in the tank The display will show a reading such as FUEL RANGE 235 MI or FUEL RANGE 378 KM 2 80 If the range is less than 50 miles 80 km the display will read LOW FUEL RANGE The fuel economy data used to determine fuel range is an average of recent driving conditions As your driving conditions change this data is gradually updated Fuel range cannot be reset Fuel Economy Pressing the SELECT down arrow while in the ECON mode displays average fuel economy and instantaneous fuel economy calculated for your specific driving conditions Average fuel economy will be shown in a reading such as 25 2 AVG MI GAL or 9 3 AVG L 100 KM Instantaneous fuel economy will be shown in a reading such as 28 INST MI GAL or 8 4 INST L 100 KM The average fuel economy is viewed as a long term approximation of your overall driving conditions If you press and hold RESET for three seconds in this mode while you re driving the system will begin figuring average fuel economy from that point in time Instantaneous fuel economy cannot be
89. 4 38 55 o EAEN 5 AER Eala 33 J 67 52 50 32 J 31 30 J 29 58 47 7 17 G6 05 04903 Ge a E 40 39 69 tote cecaco Minifuses 1 ANAND MN FW WN Usage Fuel Pump HVAC Blower Memory ALDL Rear Fog Lamps CD Driver s Door Module Air Bag System Minifuses 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Usage Not Used Right Parking Lamp Vent Solenoid Ignition 1 Left Parking Lamp Dimmer Not Used Left Front Heated Seat Not Used Rear Door Module Stoplamp NSBU Audio Retained Accessory Power RAP Not Used Not Used Passenger Door Module Body Interior Lamps 6 73 Minifuses Micro Relays 6 74 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 Usage Not Used Ignition Switch Not Used Right Front Heated Seat Not Used HVAC Ignition 3 Rear Anti Lock Brake System ABS Turn Signal Hazard HVAC Battery Dimmer Usage Fuel Pump Parking Lamp Ignition 1 Rear Fog Lamp Not Used Park Reverse Micro Relays 46 47 48 49 50 51 52 53 54 55 Circuit Breakers 56 57 Mini Relays 58 59 Usage Retained Accessory Power RAP Fuel Tank Door Lock Not Used Ignition 3 Fuel Tank Door Release Interior Lamps Trunk Release Front Courtesy Lamps Not Used Electronic Level Control ELC Usage Power Seats Power Wi
90. 6 Pull the bulb straight out to remove it from the socket 7 Replace the bulb and reverse the steps to reinstall the lamp assembly 6 46 Windshield Wiper Blade Replacement Windshield wiper blades should be inspected at least twice a year for wear or cracking See Wiper Blade Check in the Index for more information To replace the wiper blade assembly 1 Lift the wiper arm up from the windshield and set it in the vertically locked position 2 Push the tab on the wiper blade assembly and pull the assembly down enough to release it from the U hooked end of the wiper arm Slide the assembly away from the arm 3 Remove the blade 4 To reinstall the wiper blade assembly slide it over the wiper arm to engage the U hooked end on the wiper blade assembly Pull up on the assembly to lock it into place For the proper windshield wiper blade replacement length and type see Normal Maintenance Replacement Parts in the Index 6 47 Tires Your new vehicle comes with high quality tires made by a leading tire manufacturer If you ever have questions Underinflated tires pose the same danger as about your tire warranty and where to obtain service overloaded tires The resulting accident see your Oldsmobile Warranty booklet for details could cause serious injury Check all tires frequently to maintain the recommended pressure Tire pressure should be checked when your tires are cold Overinflated t
91. ATION a J Two labels on your vehicle show how much weight it may properly carry The Tire Loading Information label found on the rear edge of the driver s door tells you the proper size speed rating and recommended inflation pressure for the tires on your vehicle It also gives you important information about the number of people that can be in your vehicle and the total weight that you can carry This weight is called the Vehicle Capacity Weight and includes the weight of all occupants cargo and all nonfactory installed options a gt MFD BY GENERAL MOTORS CORP DATE GVWR GAWR FRT THIS VEHICLE CONFORMS TO AL g L e OTOR VEHICLE SAFETY BUMPER TI NTIONSTANDARDS IN EFFECT ON THE DA GM OF M WN ABOVE 200 ASS CAR Ne J The other label is the Certification label found on the rear edge of the driver s door It tells you the gross weight capacity of your vehicle called the Gross Vehicle Weight Rating GVWR The GV WR includes the weight of the vehicle all occupants fuel and cargo Never exceed the GVWR for your vehicle or the Gross Axle Weight Rating GAWR for either the front or rear axle And if you do have a heavy load you should spread it out Don t carry more than 176 lbs 80 kg in your trunk 4 29 Do not load your vehicle any heavier than the GVWR or either the maximum front or rear GAWR If you do parts on your vehicle can b
92. Armrest The front armrest opens into a storage area To open it press the lever on the side and lift up Inside you will find storage for cassettes compact discs and coins In front of the storage area is a cupholder Press and release the cupholder cover to open Do not try to pull it out Press the cupholder back to its recessed position when not in use Rear Armrest Your vehicle has a rear armrest with cupholders and a pass through feature 2 53 Rear Storage Compartment Option Your vehicle may have a rear storage armrest with cupholders and a pass through feature Lift the front of the cover on the armrest to reveal the storage space Pull down the interior door to access the trunk Convenience Net Your vehicle has a convenience net just inside the back wall of the trunk Put small loads like grocery bags behind the net It can help keep them from falling over during sharp turns or quick starts and stops The net isn t for larger heavier loads Store them in the trunk as far forward as you can You can unhook the net so that it will lie flat when you re not using it 2 54 Ashtrays and Cigarette Lighter Push and release the cover to reveal the front ashtray and cigarette lighter NOTICE Don t put papers and other things that burn into your ashtrays If you do cigarettes or other smoking materials could set them on fire causing damage To clean an ashtray make sure the cover is ope
93. Do this until the vehicle is held by the parking brake only To check the PARK P mechanism s holding ability With the engine running shift to PARK P Then release the parking brake followed by the regular brake Underbody Flushing Service At least every spring use plain water to flush any corrosive materials from the underbody Take care to clean thoroughly any areas where mud and other debris can collect Part C Periodic Maintenance Inspections Listed in this part are inspections and services which should be performed at least twice a year for instance each spring and fall You should let your dealer s service department or other qualified service center do these jobs Make sure any necessary repairs are completed at once Proper procedures to perform these services may be found in a service manual See Service and Owner Publications in the Index Steering Suspension and Front Drive Axle Boot and Seal Inspection Inspect the front and rear suspension and steering system for damaged loose or missing parts signs of wear or lack of lubrication Inspect the power steering lines and hoses for proper hook up binding leaks cracks chafing etc Clean and then inspect the drive axle boot seals for damage tears or leakage Replace seals if necessary Exhaust System Inspection Inspect the complete exhaust system Inspect the body near the exhaust system Look for broken damaged missing or out of positi
94. E PRESSURE RESET does not appear on the display after about five seconds see your dealer for service After you release the DIC RESET button TIRE PRESSURE NORMAL will appear on the display The system completes the calibration process during driving Calibration time can take 45 to 90 minutes depending on your driving habits After the system has been calibrated the system will alert the driver that a tire is low up to a maximum speed of 65 mph 105 km h Tire Inspection and Rotation Tires should be rotated every 6 000 to 8 000 miles 10 000 to 13 000 km Any time you notice unusual wear rotate your tires as soon as possible and check wheel alignment Also check for damaged tires or wheels See When It s Time for New Tires and Wheel Replacement later in this section for more information The purpose of regular rotation is to achieve more uniform wear for all tires on the vehicle The first rotation is the most important See Scheduled Maintenance Services in the Index for scheduled rotation intervals When rotating your tires always use the correct rotation pattern shown here 6 51 Don t include the compact spare tire in your tire rotation After the tires have been rotated adjust the front and rear inflation pressures as shown on the Tire Loading Information label Reset the Check Tire Pressure System See Check Tire Pressure System in the Index Make certain that all wheel nuts
95. E OIL NOW message appears Remember to reset the Oil Life System when the oil and filter have been changed See Oil Life System in the Index for information on resetting An Emission Control Service Scheduled Maintenance ENGINE OIL CHANGE ACTUAL ENGINE OIL CHANGE 7 7 Scheduled Maintenance ENGINE OIL CHANGE 7 8 Scheduled Maintenance 7 500 Miles 12 500 km Rotate tires See Tire Inspection and Rotation in the Index for proper rotation pattern and additional information See footnote 15 000 Miles 25 000 km Replace passenger compartment air filter If you drive regularly under dusty conditions the filter may require replacement more often MILEAGE Rotate tires See Tire Inspection and Rotation in the Index for proper o S E rotation pattern and additional information See footnote 22 500 Miles 37 500 km Rotate tires See Tire Inspection and Rotation in the Index for proper rotation pattern and additional information See footnote 7 9 Scheduled Maintenance 30 000 Miles 50 000 km Replace passenger compartment air filter If you drive regularly under dust ACTUAL conditions the filter may require replacement more often Inspect throttle body bore and valve plates for deposits open the throttle valve and inspect all surfaces Clean as required An Emission Control Service See footnote Rotate tires
96. HE CANADIAN GOVERNMENT If you live in Canada and you believe that your vehicle has a safety defect you should immediately notify Transport Canada in addition to notifying General Motors of Canada Limited You may write to Transport Canada 330 Sparks Street Tower C Ottawa Ontario K1A ON5 REPORTING SAFETY DEFECTS TO GENERAL MOTORS In addition to notifying NHTSA or Transport Canada in a situation like this we certainly hope you ll notify us Please call us at 1 800 442 6537 or write Oldsmobile Customer Assistance Network 16 E Judson Street P O Box 436006 Pontiac MI 48343 6006 In Canada please call us at 1 800 263 3777 English or 1 800 263 7854 French Or write General Motors of Canada Limited Customer Communication Centre 163 005 1908 Colonel Sam Drive Oshawa Ontario L1H 8P7 Ordering Owner Publications in Canada Owner s manuals are available for purchase for all current and most past model General Motors vehicles The toll free telephone number for ordering information in Canada is 1 800 668 5539 Service manuals may be purchased from Helm Incorporated using the ordering information on the following pages Please note that prices are quoted in U S dollars 8 11 2001 OLDSMOBILE SERVICE PUBLICATIONS ORDERING INFORMATION The following publications covering the operation and servicing of your vehicle can be purchased by filling out the Service Publication Order Form in this book and m
97. Have you purchased the GM Protection Plan The Plan supplements your new vehicle warranties See your Warranty and Owner Assistance booklet or your dealer for details 7 2 Introduction Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your vehicle in good working condition but also helps the environment All recommended maintenance procedures are important Improper vehicle maintenance can even affect the quality of the air we breathe Improper fluid levels or the wrong tire inflation can increase the level of emissions from your vehicle To help protect our environment and to keep your vehicle in good condition please maintain your vehicle properly Maintenance Requirements Maintenance intervals checks inspections and recommended fluids and lubricants as prescribed in this manual are necessary to keep your vehicle in good working condition Any damage caused by failure to follow recommended maintenance may not be covered by warranty How This Section is Organized This maintenance schedule is divided into five parts Part A Scheduled Maintenance Services shows what to have done and how often Some of these services can be complex so unless you are technically qualified and have the necessary equipment you should let your dealer s service department or another qualified service center do these jobs Performing maintenance work on a vehicle can be dangerous In trying to do some j
98. IRROR REVERSE YES NO If you would like to exit the selection mode without moving through each of the personal choice features simply press a different button on the DIC or turn off the ignition The personal choices you made will still be retained even without passing through each of the features In order for your personal choices to save you must press the SELECT down arrow after making your selections If you happen to move past a selection you would like to make a personal choice for press unlock on your transmitter or press the appropriate driver number on the memory seat control This will return you to the beginning of the option feature programming mode A description of each feature programmable through the DIC follows Automatic Door Locks You can program the automatic door lock feature to change to the following modes Mode 0 No automatic door lock or unlock Mode 1 All doors automatically lock when shifted out of PARK P No automatic door unlock Mode 2 All doors automatically lock when shifted out of PARK P Only the driver s door automatically unlocks when shifted into PARK P Mode 3 All doors automatically lock when shifted out of PARK P All doors automatically unlock when shifted into PARK P Mode 4 All doors automatically lock when shifted out of PARK P Only the driver s door automatically unlocks when the key is turned to LOCK Mode 5 All doors automatically lock when shifted
99. If it stays on or comes on when yov re driving there may be a problem with your traction control system and your vehicle may need service When this warning light is on the system will not limit wheel spin Adjust your driving accordingly The traction control system warning light may come on for the following reasons If you turn the system off by pressing the TC button located on the center console the warning light will come on and stay on To turn the system back on press the button again The warning light should go off See Traction Control System in the Index for more information If there s a brake system problem that is specifically related to traction control the traction control system will turn off and the warning light will come on If your brakes begin to overheat the traction control system will turn off and the warning light will come on until your brakes cool down e If the traction control system is affected by an engine related problem the system will turn off and the warning light will come on If the traction control system warning light comes on and stays on for an extended period of time when the system is turned on your vehicle needs service Traction Control System Active Light When your traction control system is limiting wheel spin this light will come on TRAC ON Slippery road conditions may exist if the traction control system active light comes on so adjust your drivi
100. Make sure that the shoulder belt crosses the shoulder 1 36 To remove and store the comfort guides squeeze the belt edges together so that you can take them out from the guides Slide the guide into its storage pocket on the side of the seatback Center Passenger Position y Lap Belt When you sit in the center seating position you will have either a lap only belt or a lap shoulder belt If the center rear seat position has a lap only belt with no retractor this part will tell you how to use the lap belt properly If the center rear seat position has a lap shoulder belt with a retractor see the part of this manual called Rear Seat Passenger Positions Lap Shoulder Belt for instructions on how to properly wear the lap shoulder belt To make the lap belt longer tilt the latch plate and pull it along the belt 1 37 To make the belt shorter pull its free end as shown until the belt is snug Buckle position and release it the same way as the lap part of a lap shoulder belt If the belt isn t long enough see Safety Belt Extender at the end of this section Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to 1 38 Children Everyone in a vehicle needs protection This includes infants and all other children Neither the distance traveled nor the age and size of the traveler changes the need for everyone to u
101. O when it is dark enough outside your low beam headlamps will automatically come on The other lamps that turn on with your headlamps will also turn on When it is bright enough outside the regular lamps will go off and your high beam headlamps change to the reduced brightness of DRL To turn off all exterior lighting at night when you are parked turn the headlamp control all the way toward OFF The DRL will turn on automatically and the HEADLAMPS SUGGESTED message will be displayed on the DIC when you move the transaxle out of PARK P If the headlamp control is in the parking lamps position at night only the parking lamps will be on If the transaxle is out of PARK P only the parking lamps will be active and the HEADLAMPS SUGGESTED message will be displayed on the DIC As with any vehicle you should turn on the regular headlamp system when you need it Automatic Headlamps The automatic headlamps will keep your headlamps on when it is dark outside and the ignition is in RUN It s possible that your headlamps may go out if you drive from a dark area into a bright area like a lighted parking lot If this happens turn on your headlamps with the regular headlamp switch Light Sensor Your automatic headlamps and Daytime Running Lamps work with the light sensor on top of the instrument panel Don t cover it up If you do it will read dark and the automatic headlamp lighting will turn on Exterior Lighting Batt
102. OMETER DATE READING SERVICED BY MAINTENANCE PERFORMED SD Section 8 Customer Assistance Information Here you will find out how to contact Oldsmobile if you need assistance This section also tells you how to obtain service publications and how to report any safety defects 8 2 Customer Satisfaction Procedure 8 7 Courtesy Transportation 8 4 Customer Assistance for Text Telephone 8 9 Warranty Information TTY Users 8 10 Reporting Safety Defects to the United 8 4 Customer Assistance Offices States Government 8 5 GM Mobility Program for Persons 8 10 Reporting Safety Defects to the with Disabilities Canadian Government 8 6 Oldsmobile Roadside Assistance Program 8 11 Reporting Safety Defects to General Motors Features and Benefits 8 11 Ordering Owner Publications in Canada 8 7 Canadian Roadside Assistance Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Oldsmobile Normally any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer s sales or service departments Sometimes however despite the best intentions of all concerned misunderstandings can occur If your concern has not been resolved to your satisfaction the following steps should be taken STEP ONE Discuss your concern with a member of dealership management Normally concerns can be quickly resolved at that level If the matter has already been reviewed with the sales ser
103. SEEK button for two seconds until SCAN appears on the display and you hear a beep Use SCAN to listen to stations for a few seconds The radio will go to a station stop for a few seconds then go on to the next station Press the SEEK button again to stop scanning If you press SEEK for more than four seconds the radio will change to PRESET SCAN mode The sound will mute while scanning and SC will appear in the display 3 11 PUSHBUTTONS The six numbered pushbuttons let you return to your favorite stations You can set up to 18 stations six AM six FM1 and six FM2 Just 1 Turn the radio on 2 Press AM FM to select the band 3 Tune in the desired station 4 Press AUTO EQ to select the equalization that best suits the type of station selected 5 Press and hold one of the six numbered buttons until you hear a beep Whenever you press that numbered button the station you set will return and the equalization that you selected will also be automatically selected for that button 6 Repeat the steps for each pushbutton PRESET SCAN Press and hold the SEEK button for more than four seconds until you hear a double beep and PRESET SCAN appears in the display Use PRESET SCAN to listen to each of your preset stations for a few seconds The radio will go to the first preset station stored on your pushbuttons stop for a few seconds then go on to the next preset station Press the SEEK button again to stop scanning presets
104. That means better braking and longer brake life If your engine ever stops while you re driving brake normally but don t pump your brakes If you do the pedal may get harder to push down If your engine stops you will still have some power brake assist But you will use it when you brake Once the power assist is used up it may take longer to stop and the brake pedal will be harder to push Anti Lock Brakes ABS Your vehicle has anti lock brakes ABS ABS is an advanced electronic braking system that will help prevent a braking skid When you start your engine and begin to drive away your anti lock brake system will check itself You may hear a momentary motor or clicking noise while this test is going on and you may even notice that your brake pedal moves a little This is normal If there s a problem with the anti lock brake system this warning light will stay on See Anti Lock Brake System Warning Light in the Index Here s how anti lock works Let s say the road is wet You re driving safely Suddenly an animal jumps out in front of you You slam on the brakes Here s what happens with ABS A computer senses that wheels are slowing down If one of the wheels is about to stop rolling the computer will separately work the brakes at each front wheel and at both rear wheels The anti lock system can change the brake pressure faster than any driver could The computer is programmed to mak
105. The air bags in your vehicle may not inflate in a crash or they could even inflate without a crash To help avoid injury to yourself or others have your vehicle serviced right away if the air bag readiness light stays on after you start your vehicle The air bag readiness light should flash for a few seconds when you turn the ignition key to RUN If the light doesn t come on then have it fixed so it will be ready to warn you if there is a problem On the DIC an AIR BAG PROBLEM message will be displayed when there is a problem with the air bag system See DIC Warnings and Messages in the Index for more information Battery Warning Light This light will come on briefly when you start the vehicle as a check to show you it is working then it should go out If it stays on or comes on while you are driving you may have a problem with the electrical charging system It could indicate that you have a generator problem or another electrical system problem Have it checked right away Driving while this light is on could drain your battery If you must drive a short distance with the light on be certain to turn off all your accessories such as the radio and climate control system On the DIC a CHECK CHARGE SYSTEM message will be displayed and a warning chime will sound See DIC Warnings and Messages in the Index for more information Brake System Warning Light Your vehicle s hydraulic brake syste
106. Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration which grades tires by treadwear traction and temperature performance This applies only to vehicles sold in the United States The grades are molded on the sidewalls of most passenger car tires The Uniform Tire Quality Grading system does not apply to deep tread winter type snow tires space saver or temporary use spare tires tires with nominal rim diameters of 10 to 12 inches 25 to 30 cm or to some limited production tires While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades they must also conform to federal safety requirements and additional General Motors Tire Performance Criteria TPC standards 6 54 Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course For example a tire graded 150 would wear one and a half 1 1 2 times as well on the government course as a tire graded 100 The relative performance of tires depends upon the actual conditions of their use however and may depart significantly from the norm due to variations in driving habits service practices and differences in road characteristics and climate Traction AA A B C The traction grades from highest to lowest are AA A
107. You may use your vehicle in making deliveries Or you may drive it to work to do errands or in many other ways Because of all the different ways people use their vehicles maintenance needs vary You may need more frequent checks and replacements So please read the following and note how you drive If you have any questions on how to keep your vehicle in good condition see your dealer This part tells you the maintenance services you should have done and when you should schedule them If you go to your dealer for your service needs yow ll know that GM trained and supported service people will perform the work using genuine GM parts The proper fluids and lubricants to use are listed in Part D Make sure whoever services your vehicle uses these All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle This schedule is for vehicles that carry passengers and cargo within recommended limits You will find these limits on your vehicle s Tire Loading Information label See Loading Your Vehicle in the Index are driven on reasonable road surfaces within legal driving limits use the recommended fuel See Fuel in the Index Scheduled Maintenance The services shown in this schedule up to 100 000 miles 166 000 km should be performed after 100 000 miles 166 000 km at the same intervals The services shown at 150 000 miles 240 000 km should be performed a
108. acceleration have to do their work where the tires meet the road Adding the sudden acceleration can demand too much of those places You can lose control Refer to Traction Control System in the Index What should you do if this ever happens Ease up on the accelerator pedal steer the vehicle the way you want it to go and slow down If you have Stabilitrak you may see the STABILITY ACTIVE message on the Driver Information Center See Stability Active Message in the Index Speed limit signs near curves warn that you should adjust your speed Of course the posted speeds are based on good weather and road conditions Under less favorable conditions you ll want to go slower 4 11 If you need to reduce your speed as you approach a curve do it before you enter the curve while your front wheels are straight ahead Try to adjust your speed so you can drive through the curve Maintain a reasonable steady speed Wait to accelerate until you are out of the curve and then accelerate gently into the straightaway Steering in Emergencies There are times when steering can be more effective than braking For example you come over a hill and find a truck stopped in your lane or a car suddenly pulls out from nowhere or a child darts out from between parked cars and stops right in front of you You can avoid these problems by braking if you can stop in time But sometimes you can t there isn t room That
109. ailing it in with your check money order or credit card information to Helm Incorporated address below CURRENT PUBLICATIONS FOR 2001 OLDSMOBILE SERVICE MANUALS Service Manuals have the diagnosis and repair information on engines transmission axle suspension brakes electrical steering body etc RETAIL SELL PRICE 120 00 TRANSMISSION TRANSAXLE TRANSFER CASE UNIT REPAIR MANUAL This manual provides information on unit repair service procedures adjustments and specifications for the 2001 GM transmissions transaxles and transfer cases RETAIL SELL PRICE 50 00 SERVICE BULLETINS Service Bulletins give technical service information needed to knowledgeably service General Motors cars and trucks Each bulletin contains instructions to assist in the diagnosis and service of your vehicle PLEASE COMPLETE THE ORDER FORM SHOWN ON THE FOLLOWING PAGE AND MAIL TO Helm Incorporated P O Box 07130 Detroit MI 48207 OWNER S INFORMATION Owner publications are written directly for Owners and intended to provide basic operational information about the vehicle The owner s manual will include the Maintenance Schedule for all models In Portfolio Includes a Portfolio Owner s Manual and Warranty Booklet RETAIL SELL PRICE 20 00 Without Portfolio Owner s Manual only RETAIL SELL PRICE 15 00 CURRENT amp PAST MODEL ORDER FORMS Service Publications are available for current and past model GM vehic
110. al Motors of Canada New Vehicle Limited Warranty alternative transportation may be available under the Courtesy Transportation Program Please consult your dealer for details General Motors reserves the right to unilaterally modify change or discontinue Courtesy Transportation at any time and to resolve all questions of claim eligibility pursuant to the terms and conditions described herein at its sole discretion Warranty Information Your vehicle comes with a separate warranty booklet that contains detailed warranty information REPORTING SAFETY DEFECTS TO THE UNITED STATES GOVERNMENT If you believe that your vehicle has a defect which could cause a crash or could cause injury or death you should immediately inform the National Highway Traffic Safety Administration NHTSA in addition to notifying General Motors If NHTSA receives similar complaints it may open an investigation and if it finds that a safety defect exists in a group of vehicles it may order a recall and remedy campaign However NHTSA cannot become involved in individual problems between you your dealer or General Motors To contact NHTSA you may either call the Auto Safety Hotline toll free at 1 800 424 9393 or 366 0123 in the Washington D C area or write to NHTSA U S Department of Transportation Washington D C 20590 You can also obtain other information about motor vehicle safety from the hotline 8 10 REPORTING SAFETY DEFECTS TO T
111. aler The arrows on your instrument panel will flash whenever you signal a turn or lane change Properly hooked up the trailer lamps will also flash telling other drivers you re about to turn change lanes or stop 4 36 When towing a trailer the arrows on your instrument panel will flash for turns even if the bulbs on the trailer are burned out Thus you may think drivers behind you are seeing your signal when they are not It s important to check occasionally to be sure the trailer bulbs are still working Driving On Grades Reduce speed and shift to a lower gear before you start down a long or steep downgrade If you don t shift down you might have to use your brakes so much that they would get hot and no longer work well Parking on Hills You really should not park your vehicle with a trailer attached on a hill If something goes wrong your rig could start to move People can be injured and both your vehicle and the trailer can be damaged But if you ever have to park your rig on a hill here s how to do it 1 Apply your regular brakes but don t shift into PARK P yet 2 Have someone place chocks under the trailer wheels 3 When the wheel chocks are in place release the regular brakes until the chocks absorb the load 4 Reapply the regular brakes Then apply your parking brake and then shift to PARK P 5 Release the regular brakes When You Are Ready to Leave After Parking on a Hill
112. all doors are unlocked second unlock button press and when locking the vehicle Parking lamps and the Daytime Running Lamps will flash twice each time the button with the unlock symbol is pressed the horn chirps when all doors are unlocked Parking lamps and the exterior lamps flash once and the horn chirps when locking the vehicle You must program this feature through the Driver Information Center DIC See DIC Personalization Programming in the Index 2 12 Matching Transmitter s to Your Vehicle Each remote lock control transmitter is coded to prevent another transmitter from unlocking your vehicle If a transmitter is lost or stolen a replacement can be purchased through your dealer Remember to bring any remaining transmitters with you when you go to your dealer When the dealer matches the replacement transmitter to your vehicle any remaining transmitters must also be matched Once your dealer has coded the new transmitter the lost transmitter will not unlock your vehicle Each vehicle can have only four transmitters matched to it See your dealer to match transmitters to another vehicle Battery Replacement Under normal use the battery in your remote lock control transmitter should last about two years You can tell the battery is weak if the transmitter won t work at the normal range in any location If you have to get close to your vehicle before the transmitter works it s probably time to change
113. alternate frequency on AF ON will appear on the display The radio may switch to stronger stations with the same broadcast Press and hold AM FM again for two seconds to turn alternate frequency off AF OFF will appear on the display The radio will not switch to other stations When you turn the ignition off and then on again the alternate frequency feature will automatically be turned on Adjusting the Speakers BAL FADE The AUDIO button adjusts balance and fade To adjust balance press and hold the AUDIO button until BAL appears on the display Turn the knob to adjust the sound to the left or right speakers The middle position balances the sound between the speakers To adjust fade press and hold the AUDIO button until FAD appears on the display Turn the knob to adjust the sound to the front or rear speakers The middle position balances the sound between the speakers Playing a Cassette Tape Your tape player is built to work best with tapes that are up to 30 to 45 minutes long on each side Tapes longer than that are so thin they may not work well in this player The longer side with the tape visible should face to the right If the ignition is on but the radio is off the tape can be inserted and will begin playing If you hear nothing but a garbled sound the tape may not be in squarely Press EJECT to remove the tape and start over 3 15 While the tape is playing use the VOL FAD BAL TREB MID BASS AUTO EQ SEEK and
114. amage caused by the use of coolant other than DEX COOL is not covered by your new vehicle warranty What to Use Use a mixture of one half clean drinkable water and one half DEX COOL coolant which won t damage aluminum parts If you use this coolant mixture you don t need to add anything else Adding only plain water to your cooling system can be dangerous Plain water or some other liquid like alcohol can boil before the proper coolant mixture will Your vehicle s coolant warning system is set for the proper coolant mixture With plain water or the wrong mixture your engine could get too hot but you wouldn t get the overheat warning Your engine could catch fire and you or others could be burned Use a 50 50 mixture of clean drinkable water and DEX COOL coolant NOTICE If you use an improper coolant mixture your engine could overheat and be badly damaged The repair cost wouldn t be covered by your warranty Too much water in the mixture can freeze and crack the engine radiator heater core and other parts If you have to add coolant more than four times a year have your dealer check your cooling system NOTICE If you use the proper coolant you don t have to add extra inhibitors or additives which claim to improve the system These can be harmful 6 27 Checking Coolant Turning the surge tank pressure cap when the engine and radiator are hot can allow steam and scalding li
115. and crisscross most large cities You Il save time and energy See the next part Freeway Driving Treat a green light as a warning signal A traffic light is there because the corner is busy enough to need it When a light turns green and just before you start to move check both ways for vehicles that have not cleared the intersection or may be running the red light One of the biggest problems with city streets is the amount of traffic on them You ll want to watch out for what the other drivers are doing and pay attention to traffic signals 4 20 Freeway Driving Mile for mile freeways also called thruways parkways expressways turnpikes or superhighways are the safest of all roads But they have their own special rules The most important advice on freeway driving is Keep up with traffic and keep to the right Drive at the same speed most of the other drivers are driving Too fast or too slow driving breaks a smooth traffic flow Treat the left lane on a freeway as a passing lane At the entrance there is usually a ramp that leads to the freeway If you have a clear view of the freeway as you drive along the entrance ramp you should begin to check traffic Try to determine where you expect to blend with the flow Try to merge into the gap at close to the prevailing speed Switch on your turn signal check your mirrors and glance over your shoulder as often as necessary Try to blend smoothly with t
116. ange Signals To signal a lane change just raise or lower the lever Headlamps until the arrow starts to flash Hold it there until you Headlamp High Low Beam Changer complete your lane change The lever will return by o Parking Lamps itself when you release it Flash To Pass Fog Lamps 2 35 As you signal a turn or a lane change if the arrows flash very fast a bulb may be burned out and other drivers won t see your turn signal If a bulb is burned out replace it to help avoid an accident If the arrows don t go on at all when you signal a turn check the fuse see Fuses and Circuit Breakers in the Index and for burned out bulbs Turn Signal On Chime If your turn signal is left on for more than 0 8 miles 1 3 km a chime will sound at each flash of the turn signal and the DIC will display the TURN SIGNAL ON reminder message To turn off the chime and message move the turn signal lever to the off position To turn off the DIC message while the turn signal is still active press any button on the DIC 2 36 Headlamps The headlamp control is located on the turn signal multifunction lever 00 Turn the control to this symbol to turn on the following Parking Lamps Sidemarker Lamps Taillamps License Plate Lamps Instrument Panel Lights o Turn the headlamp control to this symbol to turn on the following Headlamps Parking Lamps Sidemarker Lamps Taillamps e License Pla
117. ank 1 Auxiliary Power Cigarette Lighter Fog Lamps Daytime Running Lamps Horn Air Conditioner Clutch 6 69 Micro Relays 27 28 29 30 31 32 33 Mini Relays 34 35 36 37 38 39 40 6 70 Usage High Beam Headlamp Low Beam Headlamp Fog Lamps Daytime Running Lamps Horn Air Conditioner Clutch HVAC Solenoid Usage Accessory Air Pump Starter 1 Cooling Fan 2 Ignition 1 Cooling Fan Series Parallel Cooling Fan 1 Maxibreaker 41 MaxiFuses 42 43 44 45 46 47 Spare Fuses 48 49 50 51 52 53 Usage Starter Usage AIR ABS Air Pump B Air Pump A Cooling Fan 2 Cooling Fan 1 Usage Spare Not Used Not Used Not Used Not Used Fuse Puller Removing the Rear Seat Cushion To access the battery and rear compartment fuse panels the rear seat cushion must be removed This procedure is somewhat difficult You may wish to have your dealer do this for you NOTICE The battery and main fuse boxes are located under the rear seat cushion The battery s ground terminal and some relay wires are exposed To help avoid damage to the battery and wires be careful when removing or reinstalling the seat cushion Do not remove covers from covered parts Do not store anything under the seat as objects could touch exposed wires and cause a short To Remove the Rear Seat Cushion 1 Pull up on the front of the cushion to release the front hooks 2 Pull the cushion up and out to
118. are properly tightened See Wheel Nut Torque in the Index Rust or dirt on a wheel or on the parts to which it is fastened can make wheel nuts become loose after a time The wheel could come off and cause an accident When you change a wheel remove any rust or dirt from places where the wheel attaches to the vehicle In an emergency you can use a cloth or a paper towel to do this but be sure to use a scraper or wire brush later if you need to to get all the rust or dirt off See Changing a Flat Tire in the Index 6 52 When It s Time for New Tires One way to tell when it s time for new tires is to check the treadwear indicators which will appear when your tires have only 1 16 inch 1 6 mm or less of tread remaining You need a new tire if any of the following statements are true You can see the indicators at three or more places around the tire You can see cord or fabric showing through the tire s rubber The tread or sidewall is cracked cut or snagged deep enough to show cord or fabric The tire has a bump bulge or split The tire has a puncture cut or other damage that can t be repaired well because of the size or location of the damage Buying New Tires To find out what kind and size of tires you need look at the Tire Loading Information label The tires installed on your vehicle when it was new had a Tire Performance Criteria Specification TPC Spec number o
119. asher Fluid in the Index for further details At Least Once a Month Tire Inflation Check Make sure tires are inflated to the correct pressures Don t forget to check your spare tire See Tires in the Index for further details Cassette Deck Service Clean cassette deck Cleaning should be done every 50 hours of tape play See Audio Systems in the Index for further details 7 15 At Least Twice a Year Restraint System Check Make sure the safety belt reminder light and all your belts buckles latch plates retractors and anchorages are working properly Look for any other loose or damaged safety belt system parts If you see anything that might keep a safety belt system from doing its job have it repaired Have any torn or frayed safety belts replaced Also look for any opened or broken air bag coverings and have them repaired or replaced The air bag system does not need regular maintenance Wiper Blade Check Inspect wiper blades for wear or cracking Replace blade inserts that appear worn or damaged or that streak or miss areas of the windshield Also see Wiper Blades Cleaning in the Index Weatherstrip Lubrication Silicone grease on weatherstrips will make them last longer seal better and not stick or squeak Apply silicone grease with a clean cloth During very cold damp weather more frequent application may be required See Recommended Fluids and Lubricants in the Index 7 16
120. attery Saver This feature is designed to protect your vehicle s battery against drainage from the interior lamps trunk lamp glove box lamp or cigarette lighters When the ignition is turned off the power to these features will automatically turn off after 10 minutes Power will be restored for an additional 10 minutes if any door is opened the trunk is opened or the courtesy lamp switch is turned on To restore power back to the cigarette lighters the ignition must be turned back to RUN Battery Load Management The battery load management feature is designed to monitor the vehicle s electrical load and determine when the battery is in a heavy discharge condition During times of high electrical loading the engine may idle at a higher RPM setting than normal to make sure the battery charges High electrical loads may occur when several of the following are on headlamps high beams fog lamps rear window defogger high blower fan heated seats and engine cooling fans If your vehicle s battery remains in a heavy discharge condition for a long period of time the blower fan rear defogger heated seats and heated mirrors will be disabled and the DIC will display BATTERY SAVER ACTIVE This can happen either under long periods of idling or low speed driving with high electrical loading or in the event of a charging system fault 2 49 Mirrors Electrochromic Day Night Rearview Mirror with Compass Your vehicle has an e
121. ature the engine coolant temperature and the sun load Fan speed will vary as the system reaches and maintains the comfort setting you have selected To find your comfort setting start with the system in automatic mode by pressing the AUTO PUSH knob Adjust the comfort setting by using the red and blue buttons located below the digital display until you reach a setting of 75 F 24 C on the display Give the vehicle about 30 minutes to stabilize and then readjust the comfort setting if necessary The display will show the comfort setting for five seconds and then it will show the outside temperature In cold weather the system will delay turning on the fan to avoid blowing cold air The length of the delay depends on the engine coolant temperature and the outside temperature Turning the AUTO FAN knob will override this delay by turning off the automatic fan mode and changing the fan speed Your automatic electronic climate control system has a sun sensor located on the top of the instrument panel that detects direct sunlight To keep you and your passengers comfortable the system may supply cooler air to the side toward the sun Be careful not to put anything over this sun sensor The automatic electronic climate control system may not operate correctly if this sensor is covered To change the automatic electronic climate control display from an English display to a metric display push the OFF button located in the Driver Informati
122. ature that operates when the shift lever is in REVERSE R When the vehicle is shifted out of REVERSE R the passenger mirror will return to its original position after a five second delay This delay prevents movement of the mirror if multiple gear transitions REVERSE R to DRIVE D to REVERSE R occur during a parallel parking maneuver This feature can be programmed on or off through the DIC See Driver Information Center or Personalization Features in the Index for programming instructions Vehicles are delivered with this feature off Convex Outside Mirror Your passenger s side mirror is convex A convex mirror s surface is curved so you can see more from the driver s seat A convex mirror can make things like other vehicles look farther away than they really are If you cut too sharply into the right lane you could hit a vehicle on your right Check your inside mirror or glance over your shoulder before changing lanes Heated Outside Rearview Mirror If Equipped When you operate the rear window defogger the heated driver s and passenger s outside rearview mirrors also warm up to help clear them of ice and snow See Rear Window Defogger in the Index Storage Compartments Glove Box Use the master key to lock and unlock the glove box To open lift the latch release on the left side of the glove box door The VALET key will not work in the glove box door lock Front Storage
123. ay go away once the engine is warmed up This will be detected by the system and cause the light to turn on If you experience one or more of these conditions change the fuel brand you use It will require at least one full tank of the proper fuel to turn the light off If none of the above steps have made the light turn off have your dealer or qualified service center check the vehicle Your dealer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that may have developed Emissions Inspection and Maintenance Programs Some state provincial and local governments have or may begin programs to inspect the emission control equipment on your vehicle Failure to pass this inspection could prevent you from getting a vehicle registration Here are some things you need to know in order to help your vehicle pass an inspection Your vehicle will not pass this inspection if the CHECK ENGINE light is on or not working properly Your vehicle will not pass this inspection if the OBD on board diagnostic system determines that critical emission control systems have not been completely diagnosed by the system The vehicle would be considered not ready for inspection This can happen if you have recently replaced your battery or if your battery has run down The diagnostic system is designed to evaluate critical emission control systems during normal driving This may take several days of routine driv
124. ay settle up around the child s abdomen In a crash the belt would apply force on a body area that s unprotected by any bony structure This alone could cause serious or fatal injuries Young children always should be secured in appropriate child restraints 1 41 Restraint Systems for Children An infant car bed A a special bed made for use in a motor vehicle is an infant restraint system designed to restrain or position a child on a continuous flat surface Make sure that the infant s head rests toward the center of the vehicle 1 42 A rear facing infant seat B provides restraint with the seating surface against the back of the infant The harness system holds the infant in place and in a crash acts to keep the infant positioned in the restraint A forward facing child seat C E provides restraint for the child s body with the harness and also sometimes with surfaces such as T shaped or shelf like shields A booster seat F G is a child restraint designed to improve the fit of the vehicle s safety belt system Some booster seats have a shoulder belt positioner and some high back booster seats have a five point harness A booster seat can also help a child to see out the window 1 43 Q How do child restraints work A child restraint system is any device designed for use in a motor vehicle to restrain seat or position children A built in child restraint system is a permanent part of th
125. b will override this delay by turning off the automatic fan control mode and changing the fan speed Defogging and Defrosting On cool humid days use the defog setting to keep the windows clear while also providing heat through the lower outlets Turn the AUTO PUSH knob clockwise to DEF to quickly remove fog or ice from the windshield For maximum front defrost performance under extreme icing or frosting conditions increase the temperature setting to 90 F 33 C and increase the fan speed to high Rear Window Defogger E REAR Press this button to warm the defogger grid on the rear window An indicator light below the button will glow while the rear window defogger is operating At speeds above 30 mph 48 km h the rear defogger will stay on until you press the REAR button again At speeds below 30 mph 48 km h the rear window defogger will turn off automatically after about 10 minutes of use If you press it again the defogger will operate for about five minutes only You can also turn the defogger off by turning off the ignition Do not attach a temporary vehicle license across the defogger grid on the rear window When you operate the rear window defogger the outside rearview mirrors are also heated to help remove ice and fog if your vehicle is equipped with heated outside rearview mirrors For more information see Heated Outside Rearview Mirror in the Index 3 8 NOTICE Don t use a razor b
126. be programmed differently for each driver When you press the unlock symbol on the transmitter the DIC will automatically change driver numbers and the vehicle will recall the personal choice settings that were last made to correspond to your transmitter including your radio and comfort control settings See Comfort Controls Personalization in the Index If you unlock the vehicle using your door key instead of your transmitter the personal choice settings will correspond to the previous driver of the vehicle as identified by a transmitter a memory seat control or through the DIC If this happens and you were not the last driver of the vehicle press your correct driver number on the memory seat controls press the unlock symbol on your transmitter or select the personalization programming mode and choose the correct driver number 2 84 After you have the correct driver number on the display use the SELECT down arrow button to scroll through the following messages and feature options DOORS LOCK IN GEAR YES NO DOORS UNLOCK YES NO ALL DOORS IN PARK YES NO ALL DOORS AT KEY OFF YES NO DRIVERS DOOR IN PARK YES NO DRIVERS DOOR KEY OFF YES NO PASS WINDOW LOCKOUT YES NO KEY FOB FLASH LIGHTS YES NO KEY FOB CHIRP HORN YES NO DELAY LOCK OF DOORS YES NO PERIMETER LIGHTS YES NO EXT LIGHT TIMEOUT 25 DISPLAY DRIVER ID YES NO KEY FOB MEMORY SEAT YES NO DRIVING POSITION YES EXIT POSITION YES TILT M
127. bel We recommend an ACDelco battery The battery is located under the rear seat cushion To access the battery see Removing the Rear Seat Cushion in the Index You don t need to access the battery to jump start your vehicle See Jump Starting in the Index A battery that isn t properly vented can let sulfuric acid fumes into the area under the rear seat cushion These fumes can damage your rear seat safety belt systems You may not be able to see this damage and the safety belts might not provide the protection needed in a crash If a replacement battery is ever needed it must be vented in the same manner as the original battery Always make sure that the vent hose is properly reattached before reinstalling the seat cushion 6 35 To be sure the vent hose A is properly attached the vent hose connectors B must be securely reattached to the vent outlets C on each side of the battery and the vent assembly grommet D must be secured to the floor pan E 6 36 Vehicle Storage If you re not going to drive your vehicle for 25 days or more remove the black negative cable from the battery This will help keep your battery from running down Batteries have acid that can burn you and gas that can explode You can be badly hurt if you aren t careful See Jump Starting in the Index for tips on working around a battery without getting hurt Contact your dealer to learn how to prepa
128. ce 1 17 Q What s wrong with this The shoulder belt is worn under the arm It should be worn over the shoulder at all times 1 18 You can be seriously injured if you wear the shoulder belt under your arm In a crash your body would move too far forward which would increase the chance of head and neck injury Also the belt would apply too much force to the ribs which aren t as strong as shoulder bones You could also severely injure internal organs like your liver or spleen Q What s wrong with this You can be seriously injured by a twisted belt In a crash you wouldn t have the full width of the belt to spread impact forces If a belt is twisted make it straight so it can work properly or ask your dealer to fix it 3 A i as D SGIAN i J The belt is twisted across the body 1 19 To unlatch the belt just push the button on the buckle The belt should go back out of the way Before you close the door be sure the belt is out of the way If you slam the door on it you can damage both the belt and your vehicle 1 20 Safety Belt Use During Pregnancy Safety belts work for everyone including pregnant women Like all occupants they are more likely to be seriously injured if they don t wear safety belts A pregnant woman should wear a lap shoulder belt and the lap portion should be worn as low as possible below the
129. cohol or drugs with night vision problems or by fatigue 4 16 Here are some tips on night driving Drive defensively Don t drink and drive Since you can t see as well you may need to slow down and keep more space between you and other vehicles Slow down especially on higher speed roads Your headlamps can light up only so much road ahead In remote areas watch for animals If you re tired pull off the road in a safe place and rest No one can see as well at night as in the daytime But as we get older these differences increase A 50 year old driver may require at least twice as much light to see the same thing at night as a 20 year old What you do in the daytime can also affect your night vision For example if you spend the day in bright sunshine you are wise to wear sunglasses Your eyes will have less trouble adjusting to night But if you re driving don t wear sunglasses at night They may cut down on glare from headlamps but they also make a lot of things invisible You can be temporarily blinded by approaching headlamps It can take a second or two or even several seconds for your eyes to readjust to the dark When you are faced with severe glare as from a driver who doesn t lower the high beams or a vehicle with misaimed headlamps slow down a little Avoid staring directly into the approaching headlamps Keep your windshield and all the glass on your vehicle clean inside and
130. crease volume SEEK Press this button to tune to the next strong radio station When playing a cassette tape or compact disc press SEEK to hear the next selection There must be at least a three second gap between selections on a cassette tape PROG Press this button to tune in the next preset radio station When playing a cassette tape press PROG to hear the other side of a tape that is playing When listening to a disc in the CD changer press PROG to select the next loaded disc Understanding Radio Reception AM The range for most AM stations is greater than for FM especially at night The longer range however can cause stations to interfere with each other AM can pick up noise from things like storms and power lines Try reducing the treble to reduce this noise if you ever get it FM Stereo FM stereo will give you the best sound but FM signals will reach only about 10 to 40 miles 16 to 65 km Tall buildings or hills can interfere with FM signals causing the sound to come and go Cellular Phone Usage Cellular phone usage may cause interference with your vehicle s radio This interference may occur when making or receiving phone calls charging the phone s battery or simply having the phone on This interference is described as an increased level of static while listening to the radio If you notice static while listening to the radio unplug the cellular phone and turn it off Tips About Your Audio Syste
131. ction by considering the following Did you recently put fuel into your vehicle If so reinstall the fuel cap making sure to fully install the cap See Filling Your Tank in the Index The diagnostic system can determine if the fuel cap has been left off or improperly installed A loose or missing fuel cap will allow fuel to evaporate into the atmosphere A few driving trips with the cap properly installed should turn the light off Did you just drive through a deep puddle of water If so your electrical system may be wet The condition will usually be corrected when the electrical system dries out A few driving trips should turn the light off Are you low on fuel As your engine starts to run out of fuel your engine may not run as efficiently as designed since small amounts of air are sucked into the fuel line causing a misfire The system can detect this Adding fuel should correct this condition Make sure to install the fuel cap properly See Filling Your Tank in the Index It will take a few driving trips to turn the light off Have you recently changed brands of fuel If so be sure to fuel your vehicle with quality fuel See Fuel in the Index Poor fuel quality will cause your engine not to run as efficiently as designed You may notice this as stalling after start up stalling when you put the vehicle into gear misfiring hesitation on acceleration or stumbling on acceleration These conditions m
132. ction of a particular restraint should take into consideration not only the child s weight height and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used For most basic types of child restraints there are many different models available When purchasing a child restraint be sure it is designed to be used in a motor vehicle If it is the restraint will have a label saying that it meets federal motor vehicle safety standards The restraint manufacturer s instructions that come with the restraint state the weight and height limitations for a particular child restraint In addition there are many kinds of restraints available for children with special needs Newborn infants need complete support including support for the head and neck This is necessary because a newborn infant s neck is weak and its head weighs so much compared with the rest of its body In a crash an infant in a rear facing seat settles into the restraint so the crash forces can be distributed across the strongest part of an infant s body the back and shoulders Infants always should be secured in appropriate infant restraints The body structure of a young child is quite unlike that of an adult or older child for whom the safety belts are designed A young child s hip bones are still so small that vehicle s regular safety belt may not remain low on the hip bones as it should Instead it m
133. d driver The settings can also be changed by pressing one of the memory buttons 1 or 2 located on the driver s door until you hear two beeps When adjustments are made the new settings are automatically saved for that driver Automatic Electronic Climate Control Your vehicle is equipped with either a Single Zone or a Dual Zone Automatic Electronic Climate Control System You can use the automatic setting or override the automatic setting by using the manual controls Your vehicle also has the flow through ventilation system described later in this section AUTO PUSH Knob By pressing the AUTO PUSH knob you have selected the electronic climate control system to be in the automatic mode The climate control system will automatically control the air temperature air inlets air distribution and the fan speed based on your selected temperature setting as well as on the temperature inside the vehicle the outside temperature and the sun load When you press the AUTO PUSH knob the lights under the AUTO PUSH and AUTO FAN knobs will illuminate Your current comfort setting will be shown in the digital display Set the comfort level you want inside the vehicle by using the colored buttons located below the climate control display Turn the AUTO PUSH knob to select the manual air delivery mode operation of the climate control system Temperature Buttons To adjust the comfort level you want maintained inside the vehic
134. d optional features on your vehicle and information on starting shifting and braking Also explained are the instrument panel and the warning systems that tell you if everything is working properly and what to do if you have a problem Windows Keys Door Locks Remote Lock Control 4 Trunk 6 Theft 7 8 LA AAOAAN Universal Theft Deterrent PASS Key III 2 20 New Vehicle Break In 2 21 Ignition Positions 2 22 Starting Your Engine 2 25 Engine Coolant Heater If Equipped 2 26 Automatic Transaxle Operation 2 29 Parking Brake 2 30 Shifting Into PARK P 2 32 Shifting Out of PARK P 2 32 2 33 2 34 2 35 2 44 2 46 2 50 2 53 2 56 2 56 2 57 2 58 2 62 2 66 2 78 Parking Over Things That Burn Engine Exhaust Tilt Wheel Turn Signal Multifunction Lever Exterior Lamps Interior Lamps Mirrors Storage Compartments Accessory Power Outlet OnStar System If Equipped Sunroof Option HomeLink Transmitter If Equipped The Instrument Panel Your Information System Warning Lights Gages and Indicators Driver Information Center DIC Windows Leaving children in a vehicle with the windows closed is dangerous A child can be overcome by the extreme heat and can suffer permanent injuries or even death from heat stroke Never leave a child alone in a vehicle especially with the windows closed in warm or hot weather Power Windows Switches on the driver s door armrest control each of
135. ddress Expiration el go is different from your shipping Date mo yr address shown CUSTOMER SIGNATURE GM OLD ORD99 Prices are subject to change without notice and without incurring Note to Canadian Customers All listed prices are quoted in U S funds Canadian residents obligation Allow ample time for delivery are to make checks payable in U S funds To cover Canadian postage add 11 50 plus the U S order processing
136. dows if this area is clear Keep the air path under the front seats clear of objects This helps air to circulate throughout your vehicle 3 9 Steering Wheel Controls for Climate Control Some heating and cooling controls can be adjusted at the steering wheel Other touch controls also operate some audio controls See Audio Steering Wheel Controls later in this section Press the upper part of the fan symbol button to override the automatic fan control and increase the fan speed Press the lower part of the fan symbol button to override the automatic fan control and reduce the fan speed Press either arrow on the TEMP button once to display your current comfort setting in the digital display Press the upper part of the TEMP button again to provide a warmer comfort setting or press the lower part of the TEMP button again to provide a cooler comfort setting 3 10 Audio Systems Your audio system has been designed to operate easily and give years of listening pleasure You will get the most enjoyment out of it if you acquaint yourself with it first Find out what your audio system can do and how to operate all its controls to be sure you re getting the most out of the advanced engineering that went into it Setting the Clock Press and hold HR until the correct hour appears The letters AM or PM will appear on the display Then press and hold MN until the correct minute appears The clock may be set wi
137. dy to drive move the shift lever out of PARK P before you release the parking brake If torque lock does occur you may need to have another vehicle push yours a little uphill to take some of the pressure from the parking pawl in the transaxle so you can pull the shift lever out of PARK P 2 31 Shifting Out of PARK P Your vehicle has an automatic transaxle shift lock control system You have to fully apply your regular brake before you can shift from PARK P when the ignition is in RUN See Automatic Transaxle in the Index If you cannot shift out of PARK P ease pressure on the shift lever push the shift lever all the way into PARK P as you maintain brake application Then move the shift lever into the gear you want If you ever hold the brake pedal down but still can t shift out of PARK P try the following 1 Turn the key to the LOCK ignition position 2 Apply and hold the brake until the end of Step 4 3 Shift to NEUTRAL N 4 Start the vehicle and then shift to the drive gear you want 5 Take your vehicle to an authorized service center as soon as you can 2 32 Parking Over Things That Burn Things that can burn could touch hot exhaust parts under your vehicle and ignite Don t park over papers leaves dry grass or other things that can burn Engine Exhaust Engine exhaust can kill It contains the gas carbon monoxide CO which you can t see or smell It can cause
138. e Garment Hook For your convenience you will find a two hanger capacity garment hook on each rear door assist handle Garment hooks are not designed to support clothing bars Use assist handles for this if possible Sunroof Option If you have this feature the switches are located between the sun visors There are two switches that operate the sunroof The switches will only work when the ignition is on or when the Retained Accessory Power RAP is active The OPEN CLOSE switch has positions for open or close and express open The TILT CLOSE switch has positions for tilt or close Press and hold the OPEN CLOSE switch to the first position to open the glass panel and sunshade The sunshade can also be opened by hand To close the glass panel press and hold the OPEN CLOSE or TILT CLOSE switch in the close position As the glass panel closes it will open slightly towards the tilt position to provide a better seal The sunshade can only be closed by hand Press and release the OPEN CLOSE switch rearward to the second position to express open the glass panel It will stop in a partially open position The glass panel may be fully opened by pressing the OPEN CLOSE switch rearward again When the glass panel is express opening pressing either switch in any direction will stop it If you press and hold the OPEN CLOSE switch in the express open position for more than one and a half seconds the express open operation w
139. e Index You can be injured and your vehicle could be damaged if you try to do service work ona vehicle without knowing enough about it Besure you have sufficient knowledge experience the proper replacement parts and tools before you attempt any vehicle maintenance task Be sure to use the proper nuts bolts and other fasteners English and metric fasteners can be easily confused If you use the wrong fasteners parts can later break or fall off You could be hurt Adding Equipment to the Outside of Your Vehicle Things you might add to the outside of your vehicle can affect the airflow around it This may cause wind noise and affect windshield washer performance Check with your dealer before adding equipment to the outside of your vehicle Fuel If you have the 3 5L V6 engine VIN Code H use regular unleaded gasoline rated at 87 octane or higher If you have the 4 0L V8 engine VIN Code C use premium unleaded gasoline rated at 91 octane or higher for best performance You may use middle grade or regular unleaded gasolines but your vehicle s acceleration may be slightly reduced It is recommended that the gasoline meet specifications which have been developed by the American Automobile Manufacturers Association AAMA and endorsed by the Canadian Motor Vehicle Manufacturers Association for better vehicle performance and engine protection Gasolines meeting the AAMA specification could provide impr
140. e approximate When adding be sure to fill to the appropriate level as recommended in this manual Engine Specifications The following engine specifications are for the LX5 3 5L V6 VIN Engine Code 0 00 00 0000 H AD oe tinted ole eee aber nes V6 Displacement 212 cubic inches 3 5L Horsepower 0 0 eee eee eee 215 Compression Ratio 0 0000 9 3 1 Firing Order 000 1 2 3 4 5 6 Thermostat Temperature Specification 180 F 82 C The following engine specifications are for the L47 4 0L V8 VIN Engine Code 2 0 0 cee eee eee eee C Type serrera ekes aT EEEE TES Wa ee os bate ek ees V8 Displacement 279 cubic inches 4 0L Horsepower cr ne avew en cece ipno SEAS KMS 250 Compression Ratio 004 10 3 1 Firing Order 1 2 7 3 4 5 6 8 Thermostat Temperature Specification 180 F 82 C 6 77 Normal Maintenance Replacement Parts The following replacement parts are for the LX5 3 5L V6 Air Cleaner Element AC Type A 1096C Passenger Compartment Alt Filt r 5 t2 4 bat tees GM Part 25654414 Engine Oil Filter AC Type PF 58 Fuel Filter 0 0 0 AC Type GF 627 Spark Plugs 0 PT16EPR C13 GM Part 12561466 Gap 0 050 inch 1 52 mm Windshield Wiper Blades VY PC tice ech wot eae let Shepard s Hook Length
141. e motor vehicle An add on child restraint system is a portable one which is purchased by the vehicle s owner For many years add on child restraints have used the adult belt system in the vehicle To help reduce the chance of injury the child also has to be secured within the restraint The vehicle s belt system secures the add on child restraint in the vehicle and the add on child restraint s harness system holds the child in place within the restraint One system the three point harness has straps that come down over each of the infant s shoulders and buckle together at the crotch The five point harness system has two shoulder straps two hip straps and a crotch strap A shield may take the place of hip straps A T shaped shield has shoulder straps that are attached to a flat pad which rests low against the child s body A shelf or armrest type shield has straps that are attached to a wide shelf like shield that swings up or to the side 1 44 When choosing a child restraint be sure the child restraint is designed to be used in a vehicle If it is it will have a label saying that it meets federal motor vehicle safety standards Then follow the instructions for the restraint You may find these instructions on the restraint itself or in a booklet or both These restraints use the belt system in your vehicle but the child also has to be secured within the restraint to help reduce the chance of personal injury Whe
142. e player should be cleaned regularly after every 50 hours of use Your radio may display CLEAN PLAYR to indicate that you have used your tape player for 50 hours without cleaning and resetting the tape clean timer If this message appears on the display your cassette tape player needs to be cleaned It will still play tapes but you should clean it as soon as possible to prevent damage to your tapes and player If you notice a reduction in sound quality try a known good cassette to see if it is the tape or the tape player at fault If this other cassette has no improvement in sound quality clean the tape player 3 26 The recommended cleaning method for your cassette tape player is the use of a scrubbing action non abrasive cleaning cassette with pads which scrub the tape head as the hubs of the cleaner cassette turn The recommended cleaning cassette is available through your dealer GM Part No 12344789 When using a scrubbing action non abrasive cleaning cassette it is normal for the cassette to eject because your unit is equipped with a cut tape detection feature and a cleaning cassette may appear as a broken tape If the cleaning cassette ejects insert the cassette at least three times to ensure thorough cleaning You may also choose a non scrubbing action wet type cleaner which uses a cassette with a fabric belt to clean the tape head This type of cleaning cassette will not eject on its own A non scrubbing action cleaner
143. e problem A PARK BRAKE SET message will be displayed on the Driver Information Center DIC while the park brake is set and the vehicle is moving The message will not come on if the transaxle is in PARK P 2 70 Anti Lock Brake System Warning Light With the anti lock brake system the light s will come on when you start your engine and may stay on for several seconds That s normal If the light stays on turn the ignition to OFF Or if the light comes on when you re driving stop as soon as possible and turn the ignition off Then start the engine again to reset the system If the light still stays on or comes on again while you re driving your vehicle needs service If the regular brake system warning light isn t on you still have brakes but you don t have anti lock brakes If the regular brake system warning light is also on you don t have anti lock brakes and there s a problem with your regular brakes See Brake System Warning Light earlier in this section The anti lock brake system warning light should come on briefly when you turn the ignition key to RUN If the light doesn t come on then have it fixed so it will be ready to warn you if there is a problem Traction Control System Warning Light This warning light should come on briefly as you start the engine TRAC OFF If the warning light doesn t come on then have it fixed so it will be ready to warn you if there s a problem
144. e the most of available tire and road conditions You can steer around the obstacle while braking hard As you brake your computer keeps receiving updates on wheel speed and controls braking pressure accordingly Remember Anti lock doesn t change the time you need to get your foot up to the brake pedal or always decrease stopping distance If you get too close to the vehicle in front of you you won t have time to apply your brakes if that vehicle suddenly slows or stops Always leave enough room up ahead to stop even though you have anti lock brakes Using Anti Lock Don t pump the brakes Just hold the brake pedal down firmly and let anti lock work for you You may hear a motor or clicking noise during a hard stop but this is normal Braking in Emergencies With anti lock you can steer and brake at the same time In many emergencies steering can help you more than even the very best braking Traction Control System Your vehicle has a traction control system that limits wheel spin This is especially useful in slippery road conditions The system operates only if it senses that one or both of the front wheels are spinning or beginning to lose traction When this happens the system works the front brakes and reduces engine power to limit wheel spin This light will come on when your traction control system is limiting TRAC wheel spin See Traction ON Control System Active Light in the Index You may
145. e used to plug in electrical equipment such as a cellular telephone CB radio etc Follow the proper installation instructions that are included with any electrical equipment you install The accessory power outlet will only operate when the ignition is in RUN and for 10 minutes after turning the ignition off If you would like the accessory power outlet to operate regardless of ignition position and for unlimited periods of time see Engine Compartment Bussed Electrical Center in the Index or see your dealer Leaving an accessory on for a long period of time can drain the vehicle s battery OTICE When using the accessory power outlet the maximum load of any electrical equipment should not exceed 15 amps 2 56 OnStar System If Equipped Onstar is a vehicle communications service The following services are available through a subscription with OnStar and are available 24 hours a day Emergency Services Automatic Notification of Air Bag Deployment Stolen Vehicle Tracking Roadside Assistance with Location Remote Diagnostics OnStar MED NET Accident Assist Convenience Services Remote Door Unlock Route Support Concierge Services Ride Assist A complete user s guide is provided with the OnStar System For more information contact OnStar at 1 888 ONSTAR7 Assist Handles A handle above each rear door and the front passenger s door can be used to help you get in or out of your vehicl
146. ear on the display AUTO EQ Press AUTO EQ to select the desired preset equalization setting while playing a compact disc The equalization will be automatically set whenever you play a compact disc SEEK Press the reverse arrow while playing a CD to go to the start of the current track if more than eight seconds have played Press the forward arrow to go to the next track If you hold the button or press it more than once the player will continue moving backward or forward through the disc SCAN Press and hold the SEEK button for more than two seconds until you hear a beep and SCAN and the track number appear in the display Use SCAN to listen to each selection for a few seconds The disc will go to the next selection stop for a few seconds then go on to the next selection Press this button again to stop scanning The sound will mute while scanning SCAN and the track number will appear on the display RCL Press this button to see how long the current track has been playing To change what is normally shown on the display track or elapsed time press the button until you see the display you want then hold the button until the display flashes While elapsed time is showing CD TIME will appear on the display AM FM Press this button to play the radio when a disc is in the player TP CD With a cassette tape in the player and the radio playing press this button to play a cassette tape Press AM FM to return to the radio whe
147. eats Horizontal Control Raise or lower the front of the seat by pressing the forward edge of the control up or down Raise or lower the rear of the seat by holding the rear edge of the control up or down Move the seat forward or rearward by pressing the control towards the front or rear of the vehicle Move the seat higher or lower by holding the control up or down Vertical Control Option Move the seatback into a reclined position by pressing back on the control Raise the seatback by pressing forward on the control Power Lumbar Control Option The power lumbar controls are located on the outboard side of each front seat Use the power seat control first to get the proper position then continue with the lumbar adjustment To reshape the lower seatback press the lumbar control forward to increase support and rearward to decrease support Press the control up or down to raise or lower the support mechanism Keep in mind that as your seating position changes as it may during long trips so should the position of your lumbar support Adjust the seat as needed Memory Seat and Mirrors If Equipped If your vehicle has this feature the controls on the driver s door panel are used to program and recall previous settings You can use this feature to save your driver s seat position lumbar adjustment outside mirror positions personalization features comfort controls and radio settings
148. ed while trying to play a CD in the compact disc player or changer the following conditions may have caused the error The road is too rough The disc should play when the road is smoother The disc is dirty scratched wet or upside down The air is very humid If so wait about an hour and try again If any error occurs repeatedly or if an error cannot be corrected please contact your dealer If your radio displays an error number write it down and provide it to your dealer when reporting the problem Playing a Compact Disc REV 1 Press and hold this button to quickly reverse within a track As the CD reverses elapsed time will be displayed with a flashing arrow to help you find the correct passage FWD 2 Press and hold this button to quickly advance within a track As the CD advances elapsed time will be displayed with a flashing arrow to help you find the correct passage DO 3 No function when in CD changer mode RDM 4 Press this button to enter the random play mode RANDOM ALL will appear on the display While in this mode the tracks on all of the discs will be played in random order Press and hold this button to enter the single disc random play mode RANDOM ONE will appear on the display and a chime will sound Press this button again to turn off the random feature and return to normal operation SIDE 5 Press this button to select the next disc in the magazine Each time you press SIDE the
149. ehicle the interior lamps will come on if it is dark enough outside When you close the door with the ignition off the interior lamps will stay on for 25 seconds When the 25 seconds is up the lights will be turned off by the theater dimming effect Please note that locking the doors with the power door lock switch or with the lock symbol on the remote lock control transmitter will override the delayed entry lighting and the lamps will turn off immediately Theater Dimming This feature allows for a three to five second fade out of the overhead courtesy lamps instead of immediate turn off after you remove the key from the ignition They will not fade if the interior lamps are manually turned on The lower instrument panel courtesy lamps will not theater dim Delayed Exit Lighting This feature will turn on the interior lamps for 25 seconds after you remove the key from the ignition while the doors are closed and it is night This will give you time to find the door handle or lock switches as you exit the vehicle When the 25 seconds is up or if the key is reinserted into the ignition the lights will be turned off by the theater dimming effect The lamps will turn off immediately by pressing the lock symbol on the remote lock control transmitter by turning the ignition key to RUN or by activating the power door locks 2 47 Parade Dimming To activate the instrument panel backlighting during the day turn the headlamp switch to
150. elease the lever and the accelerator pedal You ll now cruise at the higher speed Move the cruise lever up to RES ACC Hold it there until you reach a desired speed and then release the lever e To increase your speed in very small amounts move the lever up to RES ACC briefly and then release it Each time you do this your vehicle will go about 1 mph 1 6 km h faster The accelerate feature will only work after you have set the cruise control speed by pushing the lever down to SET CST Reducing Speed While Using Cruise Control There are two ways to reduce your speed while using cruise control Push the lever down until you reach a desired lower speed then release it To slow down in very small amounts push the lever down briefly Each time you do this you ll go about 1 mph 1 6 km h slower Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase your speed When you take your foot off the pedal your vehicle will slow down to the cruise control speed you set earlier 2 43 Using Cruise Control on Hills How well your cruise control will work on hills depends upon your speed load and the steepness of the hills When going up steep hills you may have to step on the accelerator pedal to maintain your speed When going downhill you may have to brake or shift to a lower gear to keep your speed down Of course applying the brake takes you out of cruise control Many driver
151. ember the theft deterrent system won t activate if you lock the doors with a key or manual door lock It only activates if you use the power door lock switch or remote lock control transmitter You should also remember that you can start your vehicle with the correct ignition key if the alarm has been set off This also shuts off the alarm Here s how to avoid setting off the alarm by accident If you don t want to activate the theft deterrent system lock the door either using a key or the manual door lock switch e Always unlock a door with a key or use the remote lock control system Unlocking a door any other way will set off the alarm If you set off the alarm by accident unlock any door with your key You can also turn off the alarm by pressing the unlock symbol on the remote lock control transmitter The alarm won t stop if you try to unlock a door any other way 2 17 Testing the Alarm The alarm can be tested by following these steps 1 From inside the vehicle roll down the driver s window and open the driver s door 2 Activate the system by locking the doors with the power door lock switch while the door is open or with the remote lock control transmitter 3 Get out of the car close the door and wait for the SECURITY light to go out 4 Then reach in through the window unlock the door with the manual door lock and open the door This should set off the alarm If the alarm does not
152. en Tee ce os Sa RIGHT REAR DOOR AJAR 23 decigad ard wees SERVICE VEHICLE SOON Pa peg ice a big ice whe Ge Hee eR TURN SIGNAL ON 29 pick adeas Neda Rea RS THEFT ATTEMPTED 20 25 Sante Sede oe scce eed SERV STABILITY SYS 21 Beistime nae we ahs HEADLAMPS SUGGESTED 23 oop ke See e ke Ree DRE Ms TRUNK AJAR 29 ose ory mites Rae aes BATTERY SAVER ACTIVE BD ales glo ng ave nse le ge HOT IDLE ENGINE 33 EE bare a ES STARTING DISABLED 36 oye ce sens See aes CHECK GAS CAP AD Bap Re ask Rak ee Rear RY STABILITY ACTIVE The EXP codes are used to make translation from English to other languages easier Pressing the RESET button will remove the above messages or warnings from the DIC display unless noted by an asterisk CHECK OIL LEVEL 5 If you ever see the CHECK OIL LEVEL message it indicates that the engine oil level is 1 to 1 1 2 quarts 0 9 L to 1 4 L low The message will appear only if the engine is running and it has been at least eight minutes since the engine was last running If the message appears check the oil dipstick level If it reads low your oil level should be brought up to the proper level see Engine Oil in the Index After bringing the oil to the proper level the ignition must be off for eight minutes to allow the majority of oil to drain into the oil pan SERV STABILITY SYS 26 If you ever see the SERV STABILITY SYS message it means there may be a problem with your stability enhancement system If you
153. en all doors are unlocked second unlock button press and when locking the vehicle Mode 4 Parking lamps and the Daytime Running Lamps will flash twice each time the button with the unlock symbol is pressed the horn chirps when all doors are unlocked Parking lamps and the exterior lamps flash once and the horn chirps when locking the vehicle You can change these modes by different selections of the following DIC displays KEY FOB LIGHTS FLASH YES NO KEY FOB HORN CHIRP YES NO Press the SELECT right arrow button to toggle between your choices and change the settings Press the SELECT down arrow button to store your changes in memory and move on to the next selection If you would like to program your vehicle to Mode 1 do the following 1 Select NO for KEY FOB LIGHTS FLASH 2 Select NO for KEY FOB HORN CHIRP 2 87 If you would like to program your vehicle to Mode 2 do the following 1 Select YES for KEY FOB LIGHTS FLASH 2 Select NO for KEY FOB HORN CHIRP If you would like to program your vehicle to Mode 3 do the following 1 Select NO for KEY FOB LIGHTS FLASH 2 Select YES for KEY FOB HORN CHIRP If you would like to program your vehicle to Mode 4 do the following 1 Select YES for KEY FOB LIGHTS FLASH 2 Select YES for KEY FOB HORN CHIRP For more information on this feature see Security Feedback in the Index Delayed Locking The delayed locking feature which delays the actual
154. er Always leave just enough slack so you can turn with your rig And never allow safety chains to drag on the ground Trailer Brakes Does your trailer have its own brakes Be sure to read and follow the instructions for the trailer brakes so you ll be able to install adjust and maintain them properly Because you have anti lock brakes do not try to tap into your vehicle s brake system If you do both brake systems won t work well or at all Trailer Wiring Harness All of the electrical circuits required for your trailer lighting system can be accessed at the driver s side rear lamp connector This connector is located under the carpet in the rear corner of the trunk compartment Driving with a Trailer Towing a trailer requires a certain amount of experience Before setting out for the open road you ll want to get to know your rig Acquaint yourself with the feel of handling and braking with the added weight of the trailer And always keep in mind that the vehicle you are driving is now a good deal longer and not nearly as responsive as your vehicle is by itself Before you start check the trailer hitch and platform and attachments safety chains electrical connector lamps tires and mirror adjustment If the trailer has electric brakes start your vehicle and trailer moving and then apply the trailer brake controller by hand to be sure the brakes are working This lets you check your electrical connectio
155. er Gently brake to a stop well off the road if possible If a tire goes flat the next part shows how to use your jacking equipment to change a flat tire safely 5 18 Changing a Flat Tire If a tire goes flat avoid further tire and wheel damage by driving slowly to a level place Turn on your hazard warning flashers Changing a tire can cause an injury The vehicle can slip off the jack and roll over you or other people You and they could be badly injured Find a level place to change your tire To help prevent the vehicle from moving 1 Set the parking brake firmly 2 Put the shift lever in PARK P 3 Turn off the engine To be even more certain the vehicle won t move you can put blocks at the front and rear of the tire farthest away from the one being changed That would be the tire on the other side of the vehicle at the opposite end The following steps will tell you how to use the jack and change a tire Removing the Spare Tire and Tools The equipment you ll need is in the trunk Instructions for changing your tires are on the inside of the tire cover You can rest the cover near you for easy reference while you change the tire 1 Lift the tire cover to gain access to the spare tire and jacking equipment See Compact Spare Tire later in this section for more information about the compact spare 5 19 2 Remove the wheel wrench and jack from the jack container 3 Remove the s
156. er is on you may sometimes notice slight changes in your vehicle s engine speed and power This is normal because the system is designed to cycle the compressor on and off to keep the desired cooling and help fuel economy On very hot days open the windows long enough to let the hot air out This reduces the time required to cool the interior of the vehicle to a comfortable level If the system is in the automatic mode AUTO PUSH knob indicator light is on during very hot days the system will automatically go to the RECIRC mode and the temperature door will initially be at the full cold position for maximum cooling You can choose the extreme comfort setting of 60 F 16 C but the system will not cool any faster by choosing the extreme comfort setting Heating In cold weather if the automatic mode is selected AUTO PUSH knob indicator light is on the system will automatically direct the airflow out of the lower floor outlets and the temperature door will initially be positioned at the full hot position You can choose the extreme comfort setting of 90 F 32 C but the system will not warm up any faster by selecting the extreme comfort setting In cold weather the system will delay turning on the fan to avoid blowing cold air The length of the delay depends on the engine coolant temperature and the outside temperature The fan speed will increase as the temperature of the engine coolant increases Turning the AUTO FAN kno
157. ere leaning forward it could vehicle To read how see the part of this manual seriously injure you Safety belts help keep you in called Children position for air bag inflation before and during a crash Always wear your safety belt even with frontal air bags The driver should sit as far back There is an air bag readiness as possible while still maintaining control of the light on the instrument vehicle Front occupants should not lean on or panel which shows the sleep against the door air bag symbol The system checks the air bag electrical system for Anyone who is up against or very close to any malfunctions The light tells you if there is an electrical air bag when it inflates can be seriously injured problem See Air Bag Readiness Light in the Index or killed Air bags plus lap shoulder belts offer for more information the best protection for adults but not for young children and infants Neither the vehicle s safety CAUTION Continued 1 23 How the Air Bag Systems Work Where are the air bags The right front passenger s frontal air bag is in the instrument panel on the passenger s side The driver s side impact air bag is in the side of the The driver s frontal air bag is in the middle of the driver s seatback closest to the door steering wheel 1 24 If something is between an occupant and an air bag the bag might not inflate properly or it might force the object into that pers
158. ery Saver If the manual lamp control has been left on the exterior lamps will turn off approximately 10 minutes after the ignition is turned to LOCK and any door has been opened This protects against draining the battery in case you have accidentally left the headlamps or parking lamps on If you need to leave the lamps on for more than 10 minutes use the manual control to turn the lamps back on after the ignition has been turned to LOCK and any door has been opened To delay the lamps from turning off see Automatic Headlamps in the Index 2 45 Interior Lamps Instrument Panel Brightness Control The instrument panel brightness control is located on the driver s side of the instrument panel When it is dark outside you can brighten or dim your instrument panel cluster lights by turning the dimmer knob Turn the knob clockwise to brighten the instrument panel cluster lights and displays Turn the knob counterclockwise to dim the instrument panel cluster lights and displays If it is day and your parking lamps are on the instrument panel cluster lights and displays will come on at full intensity and will not be adjustable 2 46 If it is dark enough outside and your parking lamps are on the instrument panel cluster lights and displays and the backlighting for the door and steering column switches will come on and can also be adjusted Courtesy Lamps If it is dark enough outside and the front reading lamp
159. es available with your vehicle Automatic Door Locks Window Lockout Security Feedback Delayed Locking Perimeter Lighting Driver ID Memory Seats Parallel Park Assist Mirror Tilt Mirror To access the personalization menu the vehicle must be in PARK P with the ignition in RUN and no warning messages displayed on the DIC You must then press and hold both of the SELECT buttons for three seconds This will display the personalization menu The DIC display will show the following FEATURE PROGRAMMING PRESS SELECT DOWN TO SELECT MENU OPTIONS PRESS SELECT RIGHT TO CHANGE SETTINGS The next item to be displayed is DRIVER 1 or DRIVER 2 To change the driver number press the SELECT right arrow The driver number that you select should correspond with the number on the back of your remote lock control transmitter Once the correct driver number has been selected press the SELECT down arrow to enter your choice and move on to the next selection 2 83 The DIC is used to program the personal choices of two drivers The drivers are recognized as DRIVER 1 and DRIVER 2 You will let the DIC and the vehicle know which driver you are by using your remote lock control transmitter or by pressing the appropriate memory seat control button located on the driver s door or choosing the driver with the DIC Each remote lock control transmitter was pre programmed to belong to DRIVER 1 or DRIVER 2 The personalization features may
160. etal engine part Don t connect positive to negative or you ll get a short that would damage the battery and maybe other parts too Also don t connect the negative cable to the negative terminal on the dead battery Fans or other moving engine parts can injure you badly Keep your hands away from moving parts once the engine is running Connect the red positive cable to the remote positive terminal of the vehicle with the dead battery Don t let the other end touch metal Connect it to the positive terminal of the good battery Use a remote positive terminal if the vehicle has one 10 9 Now connect the black negative cable to the good battery s negative terminal Don t let the other end of the negative cable touch anything until the next step The other end of the negative cable doesn t go to the dead battery If you have the 3 5L V6 engine it goes to a heavy unpainted metal part on the engine of the vehicle with the dead battery Don t allow the red and black handles in the jumper cable to touch each other 11 12 If you have the 4 0L V8 engine your vehicle has a remote negative terminal marked GND located near the power steering fluid reservoir Attach the cable to the remote negative terminal provided See Engine Compartment Overview in the Index for more information on location Now start the
161. etractor see the part called Securing a Child Restraint in the Center Rear Seat Position Lap Only Belt for instructions on how to secure a child restraint You ll be using the lap shoulder belt See the earlier part about the top strap if the child restraint has one Be sure to follow the instructions that came with the child restraint Secure the child in the child restraint when and as the instructions say 1 47 1 Put the restraint on the seat 2 Pick up the latch plate and run the lap and shoulder portions of the vehicle s safety belt through or around the restraint The child restraint instructions will show you how 3 Buckle the belt Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to Tilt the latch plate to adjust the belt if needed If the shoulder belt goes in front of the child s face or neck put it behind the child restraint 1 48 4 To tighten the belt pull up on the shoulder belt while you push down on the child restraint If you re using a forward facing child restraint you may find it helpful to use your knee to push down on the child restraint as you tighten the belt 5 Push and pull the child restraint in different directions to be sure it is secure To remove the child restraint just unbuckle the vehicle s safety belt and let it go back all the way The safety belt will move freely again and be ready to work
162. f fuels used repairs may not be covered by your warranty Some gasolines that are not reformulated for low emissions may contain an octane enhancing additive called methylcyclopentadienyl manganese tricarbonyl MMT ask your service station operator whether or not the fuel contains MMT General Motors does not recommend the use of such gasolines If fuels containing MMT are used spark plug life may be reduced and your emission control system performance may be affected The malfunction indicator lamp on your instrument panel may turn on If this occurs return to your authorized Oldsmobile dealer for service To provide cleaner air all gasolines in the United States are now required to contain additives that will help prevent deposits from forming in your engine and fuel system allowing your emission control system to function properly Therefore you should not have to add anything to the fuel In addition gasolines containing oxygenates such as ethers and ethanol and reformulated gasolines may be available in your area to contribute to clean air General Motors recommends that you use these gasolines particularly if they comply with the specifications described earlier NOTICE Your vehicle was not designed for fuel that contains methanol Don t use it It can corrode metal parts in your fuel system and also damage plastic and rubber parts That damage wouldn t be covered under your warranty Fuels in Foreign Countr
163. feature press and hold the P TYPE button until you hear a beep on the PTY you want to interrupt on An asterisk will appear next to the PTY name for example CLASSICAL When you are listening to a cassette or compact disc the last selected RDS FM station will interrupt play if that selected PTY format is broadcast PUSHBUTTONS The six numbered pushbuttons let you return to your favorite Program Types PTYs These buttons have factory PTY presets You can set up to 12 PTYs six FM1 and six FM2 Just 1 Press P TYPE if it is not already on 2 Press AM FM to select FM1 or FM2 3 Turn the SELECT knob to select a PTY A Press and hold one of the six numbered buttons until you hear a beep Whenever you press that numbered button the PTY you set will return 5 Repeat the steps for each pushbutton ALERT This type of announcement warns of national or local emergencies You will not be able to turn off alert announcements ALERT appears on the display when an alert announcement plays When an alert announcement comes on the tuned radio station you will hear it even if the volume is muted or a cassette tape or compact disc is playing If the cassette tape or compact disc player is playing play will stop for the announcement and resume when the announcement is finished ALTERNATE FREQUENCY This feature allows the radio to switch to a stronger station with the same broadcast Press and hold AM FM for two seconds to turn
164. few seconds The tape will go to the next selection stop for a few seconds then go on to the next selection Press this button again to stop scanning AM FM Press this button to play the radio when a tape is in the player The tape will stop but remain in the player TP CD With a compact disc in the player and the radio playing press this button to play a compact disc Press AM FM to return to the radio when a compact disc is playing Press TP CD to switch between the tape and compact disc if both are loaded The inactive tape or CD will remain safely inside the radio for future listening The display will show TAPE and CD icons If you have the optional CD changer and the CD changer is loaded the TP CD button will activate the changer and an icon will be lit in the display EJECT Press this button to remove the tape The radio will play EJECT may be activated with either the ignition or radio off Cassettes may be loaded with the radio and ignition off if this button is pressed first CLEAN PLAYR If this message appears on the display the cassette tape player needs to be cleaned It will still play tapes but you should clean it as soon as possible to prevent damage to the tapes and player See Care of Your Cassette Tape Player in the Index After you clean the player press and hold EJECT for five seconds to reset the CLEAN PLAYR indicator The radio will display CLEANED to show the indicator was reset 3 17 Play
165. for ALL DOORS IN PARK Select NO for ALL DOORS AT KEY OFF Select NO for DRIVERS DOOR IN PARK Select YES for DRIVERS DOOR KEY OFF If you would like to program your vehicle to Mode 5 do the following 1 Select YES for DOORS LOCK IN GEAR 2 Select YES for DOORS UNLOCK 3 Select NO for ALL DOORS IN PARK 4 Select YES for ALL DOORS AT KEY OFF See Automatic Door Locks in the Index for more information about this feature sr a a Window Lockout Personalization The number of passenger windows locked out by the window LOCK switch can be programmed through the DIC Press the SELECT right arrow button to toggle between your choices and change the settings Press the SELECT down arrow button to store your changes in memory and move on to the next selection If you select YES for PASS WINDOW LOCKOUT all three passenger window switches will be locked out when the window LOCK switch is on If you select NO for PASS WINDOW LOCKOUT only the two rear passenger window switches will be locked out when the window LOCK switch is on For more information on this feature see Window Lock in the Index Security Feedback You can program the security feedback feature to change to the following modes Mode 1 No feedback when locking or unlocking the vehicle Mode 2 Parking lamps and the Daytime Running Lamps will flash twice when unlocking the vehicle and flash once when locking the vehicle Mode 3 Horn chirps wh
166. g it all the way to the right When the door is closed the changer will begin checking for discs in the magazine This will continue for up to one and a half minutes depending on the number of discs loaded To eject the magazine from the player slide the CD changer door all the way open The magazine will automatically eject Remember to keep the door closed whenever possible to keep dirt and dust from getting inside the changer 3 21 All of the CD functions are controlled by the radio buttons except for ejecting the magazine Whenever a CD magazine with discs is loaded in the changer the compact disc symbol will appear on the radio display If the CD changer is checking the magazine for CDs the compact disc symbol will flash on the display until the changer is ready to play If CD changer mode is entered during initialization LOADING will appear on the display When a CD begins playing a disc and track number will be displayed The disc numbers are listed on the front of the magazine Compact Disc Errors If an error appears on the display an error has occurred and the compact disc temporarily cannot play The CD changer will send an error message to the receiver to indicate PLAYER OPEN CD Changer Door Open Completely close the door to restore normal operation NOCD S CD Changer Cartridge Empty Try the magazine again with a disc loaded on one of the trays 3 22 CHECK CD If this error message is display
167. ge the soiled area with cool water Ifa stain remains follow the Multi Purpose Interior Cleaner instructions described earlier 3 If an odor lingers after cleaning vomit or urine treat the area with a water baking soda solution 1 teaspoon 5 ml of baking soda to 1 cup 250 ml of lukewarm water 4 Let dry Stains caused by candy ice cream mayonnaise chili sauce and unknown stains can be removed as follows 1 Carefully scrape off excess stain 2 First clean with cool water and allow to dry completely 3 Ifa stain remains follow instructions for Multi Purpose Interior Cleaner 6 59 Cleaning Vinyl Use warm water and a clean cloth Rub with a clean damp cloth to remove dirt You may have to do it more than once Things like tar asphalt and shoe polish will stain if you don t get them off quickly Use a clean cloth and a vinyl leather cleaner See your dealer for this product Cleaning Leather Use a soft cloth with lukewarm water and a mild soap or saddle soap and wipe dry with a soft cloth Then let the leather dry naturally Do not use heat to dry For stubborn stains use a leather cleaner See your dealer for this product Never use oils varnishes solvent based or abrasive cleaners furniture polish or shoe polish on leather Soiled or stained leather should be cleaned immediately If dirt is allowed to work into the finish it can harm the leather 6 60 Cleaning the To
168. ghting and the taillamps will turn on For more information see Wiper Activated Headlamps in the Index For a single wiping cycle move the lever down to MIST Hold it there until the wipers start then release it The wipers will stop after one cycle If you want more cycles hold the lever to MIST longer For steady wiping at low speed move the lever up to the LO position For high speed wiping move the lever up further to HI To stop the wipers move the lever to OFF You can set the wiper speed for a long or short delay between wiper cycles This can be very useful in light rain or snow Move the lever up to the first detent INT Turn the band labeled INT ADJ down towards the shorter lines for fewer wiper passes per minute As you turn the band towards the longer lines the wiper cycles per minute will increase Remember that damaged wiper blades may prevent you from seeing well enough to drive safely To avoid damage be sure to clear ice and snow from the wiper blades before using them If they re frozen to the windshield carefully loosen or thaw them If your blades do become damaged get new blades or blade inserts See Windshield Wiper Blade Replacement in the Index Heavy snow or ice can overload your wipers A circuit breaker will stop them until the motor cools Clear away snow or ice to prevent an overload 2 39 Rainsense Wipers If Equipped The moisture sensor is mounted on the passenger s
169. h the same as the year Use the SELECT buttons to reach the current month and press RESET The DIC will then ask for the day The day will flash the same as the year Use the SELECT buttons to reach the current day Press the RESET button again and the set display will stop flashing and go back to the normal operation mode Elapsed Time ET When the ignition is on the DIC can be used as a stopwatch The display will show hours and minutes The elapsed time indicator will record up to 100 hours then it will reset to zero and continue counting Press SELECT down arrow while in the DATE ET mode and the display will show the amount of time that has elapsed since the elapsed time indicator was last reset not including time the ignition is off such as 01 08 ELAPSED TIME To start or stop the counting of time press the RESET button briefly If the colon in the time is flashing time is being counted Time is displayed in hours and minutes Seconds are not displayed Time will continue to be counted as long as the ignition is on even if another display is being shown on the DIC To reset elapsed time to zero press RESET button for three seconds while the elapsed time is displayed 2 79 Fuel Press SELECT down arrow while in the FUEL mode to see how much fuel has been used and the fuel range functions Fuel Used While in the FUEL USED function the display will show a reading such as FUEL USED 10 4 GAL or FUEL USED
170. haracter boxes for approximately two seconds After two seconds the mirror will display the compass heading Compass Calibration If after two seconds the display does not show a compass heading N for North for example there may be a strong magnetic field interfering with the compass Such interference may be caused by a magnetic antenna mount magnetic note pad holder or a similar magnetic item If the letter C should ever appear in the compass window the compass may need calibration The mirror can be calibrated in one of two ways Drive the vehicle in circles at 5 mph 8 km h or less until the display reads a direction or drive the vehicle on your everyday routine Mirrors equipped with OnStar controls can be placed in calibration mode by pressing and holding the on off button until a C is shown in the compass display Compass Variance The mirror is set in zone eight upon leaving the factory It will be necessary to adjust the compass to compensate for compass variance if you live outside zone eight Under certain circumstances as during a long distance cross country trip it will be necessary to adjust for compass variance Compass variance is the difference between earth s magnetic north and true geographic north If not adjusted to account for compass variance your compass could give false readings To adjust for compass variance 1 Find your current location and variance zone number o
171. he traffic flow Once you are on the freeway adjust your speed to the posted limit or to the prevailing rate if it s slower Stay in the right lane unless you want to pass Before changing lanes check your mirrors Then use your turn signal Just before you leave the lane glance quickly over your shoulder to make sure there isn t another vehicle in your blind spot Once you are moving on the freeway make certain you allow a reasonable following distance Expect to move slightly slower at night When you want to leave the freeway move to the proper lane well in advance If you miss your exit do not under any circumstances stop and back up Drive on to the next exit 4 21 The exit ramp can be curved sometimes quite sharply The exit speed is usually posted Reduce your speed according to your speedometer not to your sense of motion After driving for any distance at higher speeds you may tend to think you are going slower than you actually are Before Leaving on a Long Trip Make sure you re ready Try to be well rested If you must start when you re not fresh such as after a day s work don t plan to make too many miles that first part of the journey Wear comfortable clothing and shoes you can easily drive in Is your vehicle ready for a long trip If you keep it serviced and maintained it s ready to go If it needs service have it done before starting out Of course yov ll find e
172. heel to go straight down the roadway Passing The driver of a vehicle about to pass another on a two lane highway waits for just the right moment accelerates moves around the vehicle ahead then goes back into the right lane again A simple maneuver Not necessarily Passing another vehicle on a two lane highway is a potentially dangerous move since the passing vehicle occupies the same lane as oncoming traffic for several seconds A miscalculation an error in judgment or a brief surrender to frustration or anger can suddenly put the passing driver face to face with the worst of all traffic accidents the head on collision So here are some tips for passing Drive ahead Look down the road to the sides and to crossroads for situations that might affect your passing patterns If you have any doubt whatsoever about making a successful pass wait for a better time Watch for traffic signs pavement markings and lines If you can see a sign up ahead that might indicate a turn or an intersection delay your pass A broken center line usually indicates it s all right to pass providing the road ahead is clear Never cross a solid line on your side of the lane or a double solid line even if the road seems empty of approaching traffic 4 13 Do not get too close to the vehicle you want to pass while you re awaiting an opportunity For one thing following too closely reduces your area of vision especially
173. here is still some pressure left 5 16 With the coolant surge tank pressure cap off start the engine and let it run until you can feel the upper radiator hose getting hot Watch out for the engine cooling fans By this time the coolant level inside the coolant surge tank may be lower If the level is lower add more of the proper mixture to the coolant surge tank until the level reaches the base of the filler neck A CAUTION ENGINE COOLANT 5 Then replace the pressure cap Be sure the arrows on the pressure cap line up like this If a Tire Goes Flat It s unusual for a tire to blow out while you re driving especially if you maintain your tires properly If air goes out of a tire it s much more likely to leak out slowly But if you should ever have a blowout here are a few tips about what to expect and what to do If a front tire fails the flat tire will create a drag that pulls the vehicle toward that side Take your foot off the accelerator pedal and grip the steering wheel firmly Steer to maintain lane position and then gently brake to a stop well out of the traffic lane A rear blowout particularly on a curve acts much like a skid and may require the same correction you d use in a skid In any rear blowout remove your foot from the accelerator pedal Get the vehicle under control by steering the way you want the vehicle to go It may be very bumpy and noisy but you can still ste
174. how much oil you have in your engine So be sure to check your oil level often See Engine Oil in the Index 2 81 Gage Pressing the SELECT down arrow while in GAGE mode will allow you to access the battery volts oil pressure and tire pressure displays Pressing and holding the RESET button for three seconds while in average speed and tire pressure displays will reset them Pressing the SELECT down arrow in GAGE mode will show the following displays Battery voltage such as VOLTS 13 8 Oil pressure such as OIL PRESSURE 40 PSI or OIL PRESSURE 276 KPA Average speed such as AVG SPEED 55 MPH or AVG SPEED 90 KM H 2 82 Tire pressure status such as TIRE PRESSURE NORMAL or LOW TIRE PRESSURE TIRE PRESSURE NORMAL appears when the Check Tire Pressure System believes your vehicle s tire pressures are normal If a potential tire pressure problem is detected the display will show LOW TIRE PRESSURE If you see this message you should stop as you can and check all four tires for damage If a tire is flat see If a Tire Goes Flat in the Index Also check the tire pressure in all four tires as soon as you can See Tire Pressure in the Index There are times when you will have to reset calibrate the Check Tire Pressure System See Check Tire Pressure System in the Index for more information DIC Personalization The DIC can be used to program the following personal choice featur
175. hten the belt 6 Push and pull the child restraint in different directions to be sure it is secure To remove the child restraint just unbuckle the vehicle s safety belt It will be ready to work for an adult or larger child passenger 1 51 Securing a Child Restraint in the Right Although a rear seat is a safer place you can secure a Front Seat Position forward facing child restraint in the right front seat You ll be using the lap shoulder belt See the earlier Ys part about the top strap if the child restraint has one hy Be sure to follow the instructions that came with the child restraint Secure the child in the child restraint when and as the instructions say 1 Because your vehicle has a right front passenger air 7 bag always move the seat as far back as it will go before securing a forward facing child restraint Your vehicle has a right front passenger air bag Never See Seats in the Index put a rear facing child restraint in this seat Here s why 2 Put the restraint on the seat 3 Pick up the latch plate and run the lap and shoulder portions of the vehicle s safety belt through or around the restraint The child restraint instructions will show you how A child in a rear facing child restraint can be If the shoulder belt goes in front of the child s face or seriously injured or killed if the right front neck put it behind the child restraint passenger s air bag inflates This i
176. icle Certification and Service Parts labels and the certificates of title and registration 6 66 Engine Identification The 8th character in your VIN is the engine code This code will help you identify your engine specifications and replacement parts Service Parts Identification Label You ll find this label on the underside of the spare tire cover It s very helpful if you ever need to order parts On this label is your VIN the model designation paint information and e a list of all production options and special equipment Be sure that this label is not removed from the vehicle Electrical System Add On Electrical Equipment NOTICE Don t add anything electrical to your vehicle unless you check with your dealer first Some electrical equipment can damage your vehicle and the damage wouldn t be covered by your warranty Some add on electrical equipment can keep other components from working as they should Your vehicle has an air bag system Before attempting to add anything electrical to your vehicle see Servicing Your Air Bag Equipped Vehicle in the Index Headlamp Wiring The headlamp wiring is protected by a circuit breaker in the wiring harness An electrical overload will cause the lamps to go on and off or in some cases to remain off If this happens have your headlamp system checked right away Windshield Wiper Fuses The windshield wiper motor is protected by an interna
177. icle is well ventilated with a comfortably cool interior Keep your eyes moving Scan the road ahead and to the sides Check your rearview mirrors and your instruments frequently If you get sleepy pull off the road into a rest service or parking area and take a nap get some exercise or both For safety treat drowsiness on the highway as an emergency Hill and Mountain Roads Driving on steep hills or mountains is different from driving in flat or rolling terrain 4 23 If you drive regularly in steep country or if you re planning to visit there here are some tips that can make your trips safer and more enjoyable Keep your vehicle in good shape Check all fluid levels and also the brakes tires cooling system and transaxle These parts can work hard on mountain roads Know how to go down hills The most important thing to know is this let your engine do some of the slowing down Shift to a lower gear when you go down a steep or long hill If you don t shift down your brakes could get so hot that they wouldn t work well You would then have poor braking or even none going down a hill You could crash Shift down to let your engine assist your brakes on a steep downhill slope 4 24 Coasting downhill in NEUTRAL N or with the ignition off is dangerous Your brakes will have to do all the work of slowing down They could get so hot that they wouldn t work well You would then have po
178. ies If you plan on driving in another country outside the United States or Canada the proper fuel may be hard to find Never use leaded gasoline or any other fuel not recommended in the previous text on fuel Costly repairs caused by use of improper fuel wouldn t be covered by your warranty To check on fuel availability ask an auto club or contact a major oil company that does business in the country where you ll be driving You can also write us at the following address for advice Just tell us where you re going and give your Vehicle Identification Number VIN General Motors Overseas Distribution Corporation 1908 Colonel Sam Drive Oshawa Ontario L1H 8P7 Filling Your Tank Gasoline vapor is highly flammable It burns violently and that can cause very bad injuries Don t smoke if you re near gasoline or refueling your vehicle Keep sparks flames and smoking materials away from gasoline The cap is behind a hinged door on the driver s side of the vehicle To open the fuel door press the button located on the driver s door trim near the trunk release button The ignition does not need to be on The remote fuel door release will work in all transaxle positions The trunk release lockout switch must be in OFF for the fuel door to open The fuel door can be opened manually in case of an electrical power failure To do so first open the Z trunk The release mechanism is located o
179. if you re following a larger vehicle Also you won t have adequate space if the vehicle ahead suddenly slows or stops Keep back a reasonable distance When it looks like a chance to pass is coming up start to accelerate but stay in the right lane and don t get too close Time your move so you will be increasing speed as the time comes to move into the other lane If the way is clear to pass you will have a running start that more than makes up for the distance you would lose by dropping back And if something happens to cause you to cancel your pass you need only slow down and drop back again and wait for another opportunity If other cars are lined up to pass a slow vehicle wait your turn But take care that someone isn t trying to pass you as you pull out to pass the slow vehicle Remember to glance over your shoulder and check the blind spot 4 14 Check your mirrors glance over your shoulder and start your left lane change signal before moving out of the right lane to pass When you are far enough ahead of the passed vehicle to see its front in your inside mirror activate your right lane change signal and move back into the right lane Remember that your right outside mirror is convex The vehicle you just passed may seem to be farther away from you than it really is Try not to pass more than one vehicle at a time on two lane roads Reconsider before passing the next vehicle Don t overtake a slowly
180. ill be overridden and the sunroof will operate manually To tilt open the glass panel press and hold the TILT CLOSE switch The sunshade must be opened by hand To close the glass panel press and hold the TILT CLOSE or OPEN CLOSE switch in the close position 2 57 HomeLink Transmitter If Equipped 7 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 2 58 This device complies with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Changes and modifications to this system by other than an authorized service facility could void authorization to use this equipment Programming the HomeLink Transmitter Do not use the HomeLink Transmitter with any garage door opener that does not have the stop and reverse safety feature This includes any garage door opener model manufactured before April 1 1982 Be sure that people and objects are clear of the garage door you are programming Your vehicle s engine should be turned off while programming the transmitter Follow these steps to program up t
181. ing If you have done this and your vehicle still does not pass the inspection for lack of OBD system readiness see your dealer or qualified service center to prepare the vehicle for inspection 2 75 Oil Pressure Light If you have a problem with your oil this light may stay on after you start your engine or come on when you are driving A warning chime and the DIC message LOW OIL PRESSURE may also come on These indicate that oil is not going through your engine quickly enough to keep it cool The engine could be low on oil or could have some other oil problem Have it fixed right away The oil light could also come on briefly when the ignition is on but the engine is not running The light will come on as a test to show you it is working but the light will go out about five seconds after you turn the ignition to START If it doesn t come on with the ignition on you may have a problem with the fuse or bulb Have it fixed right away 2 76 Don t keep driving if the oil pressure is low If you do your engine can become so hot that it catches fire You or others could be burned Check your oil as soon as possible and have your vehicle serviced NOTICE Damage to your engine from neglected oil problems can be costly and is not covered by your warranty Cruise Light The CRUISE light comes on whenever you set your cruise control See Cruise Control in the Index CRUISE This light will come on for a
182. ing chime when you turn the ignition off remove the key from the ignition and open the driver s door Flash to Pass This feature lets you use your high beam headlamps to signal a driver in front of you that you want to pass It works even if your headlamps are off To use it pull the turn signal lever toward you Your high beam headlamps will turn on They stay on as long as you hold the lever there Release the lever to turn them off If your headlamps are on and on high beam your headlamps will switch to low beam when the lever is released To get back to high beam push the lever away from you 2 38 Fog Lamps To turn on only the front fog lamps turn the fog lamp band to the single fog lamp symbol To turn on both the front and rear fog lamps turn the fog lamp band to the double fog lamp symbol Turning on the front fog lamps only will automatically activate the parking lamps Turning on the front and rear fog lamps will automatically activate the parking lamps and headlamps To turn off the fog lamps turn the band to OFF The front fog lamps will also turn off when you turn on your high beam headlamps but will turn on again when you switch to low beams Windshield Wipers The lever on the right side of your steering column operates your windshield wipers If your windshield wipers are on for more than six seconds while you are driving the low beam headlamps instrument panel cluster backli
183. ing a Compact Disc With the ignition on insert a disc partway into the slot label side up The player will pull it in and the disc should begin playing If you want to insert a CD when the ignition is off first press EJECT or the RCL knob Note that when the disc is inserted the CD symbol will be displayed If you select an EQ setting for your CD it will be activated each time you play a CD As each new track starts to play the track number will appear on the display If CHECK CD appears on the radio display and the disc comes out it could be that The road is too rough The disc should play when the road is smoother The disc is dirty scratched wet or upside down The air is very humid If so wait about an hour and try again If any error occurs repeatedly or if an error can t be corrected please contact your dealer If your radio displays an error message write it down and provide it to your dealer when reporting the problem 3 18 REV 1 Press and hold this button to reverse quickly within a track You will hear sound at a reduced volume The display will show elapsed time Release it to play the passage FWD 2 Press and hold this button to advance quickly within a track You will hear sound at a reduced volume The display will show elapsed time Release it to play the passage RDM 4 Press this button to hear the tracks in random rather than sequential order RDM and the track number will app
184. ing system or every 60 months since last service whichever occurs first See Engine Coolant in the Index for what to use Inspect hoses Clean radiator condenser pressure cap and neck Pressure test the cooling system and pressure cap An Emission Control Service DATE ACTUAL MILEAGE SERVICED BY DATE ACTUAL MILEAGE SERVICED BY DATE ACTUAL MILEAGE SERVICED BY 7 14 Part B Owner Checks and Services Listed in this part are owner checks and services which should be performed at the intervals specified to help ensure the safety dependability and emission control performance of your vehicle Be sure any necessary repairs are completed at once Whenever any fluids or lubricants are added to your vehicle make sure they are the proper ones as shown in Part D At Each Fuel Fill It is important for you or a service station attendant to perform these underhood checks at each fuel fill Engine Oil Level Check Check the engine oil level and add the proper oil if necessary See Engine Oil in the Index for further details Engine Coolant Level Check Check the engine coolant level and add DEX COOL coolant mixture if necessary See Engine Coolant in the Index for further details Windshield Washer Fluid Level Check Check the windshield washer fluid level in the windshield washer tank and add the proper fluid if necessary See Windshield W
185. ing the Radio Clock Steering Wheel Controls Radio Cassette Player CD Player Your Driving and the Road Defensive Driving Driving Tips for Various Road Conditions Drunken Driving Recreational Vehicle Towing Control of Vehicle Loading Your Vehicle Braking Towing a Trailer Steering Problems on the Road Hazard Warning Flashers Engine Overheating J ump Starting Changing a Flat Tire Towing Your Vehicle If You re Stuck iii iv S Section 6 VVVVVYVY Table of Contents cont d Fuel Checking Fluids and Lubricants GM Oil Life System Engine Air Cleaner Filter Passenger Compartment Air Filter Brakes Bulb Replacement Scheduled Maintenance Owner Checks and Services Periodic Maintenance Inspections Service and Appearance Care Windshield Wiper Blade Replacement Tires and Wheels Appearance Care Electrical System Fuses and Circuit Breakers Capacities and Specifications Normal Maintenance Replacement Parts Maintenance Schedule Recommended Fluids and Lubricants Maintenance Records ZD Table of Contents cont d Customer Assistance Information Customer Satisfaction Procedures Warranty Information See Warranty M anual Customer Assistance Offices Reporting Safety Defects on page 8 10 Roadside Assistance and Courtesy Transportation amp Service Publications Please refer to the last page of this manual for your Se
186. inse the vehicle well removing all soap residue completely You can get GM approved cleaning products from your dealer See Appearance Care and Materials in the Index Don t use cleaning agents that are petroleum based or that contain acid or abrasives All cleaning agents should be flushed promptly and not allowed to dry on the surface or they could stain Dry the finish with a soft clean chamois or an all cotton towel to avoid surface scratches and water spotting High pressure car washes may cause water to enter your vehicle 6 62 Cleaning Exterior Lamps Lenses Use lukewarm or cold water a soft cloth and a car washing soap to clean exterior lamps and lenses Follow instructions under Washing Your Vehicle Finish Care Occasional waxing or mild polishing of your vehicle by hand may be necessary to remove residue from the paint finish You can get GM approved cleaning products from your dealer See Appearance Care and Materials in the Index Your vehicle has a basecoat clearcoat paint finish The clearcoat gives more depth and gloss to the colored basecoat Always use waxes and polishes that are non abrasive and made for a basecoat clearcoat paint finish NOTICE Machine compounding or aggressive polishing on a basecoat clearcoat paint finish may dull the finish or leave swirl marks Foreign materials such as calcium chloride and other salts ice melting agents road oil and tar tree sap
187. ion 6 Fuel ela Use unleaded gas only Engine Oil Remote Fuel See Section 6 See Section 6 Door Release See Section 6 SD Section 1 Seats and Restraint Systems Here you ll find information about the seats in your vehicle and how to use your safety belts properly You can also learn about some things you should not do with air bags and safety belts 1 2 Seats and Seat Controls 1 34 1 8 Safety Belts They re for Everyone 1 12 Here Are Questions Many People Ask 1 36 About Safety Belts and the Answers 1 38 13 How to Wear Safety Belts Properly 1 42 14 Driver Position 1 54 20 Safety Belt Use During Pregnancy 1 57 21 Right Front Passenger Position 1 58 21 Air Bag Systems 1 58 Rear Seat Passengers Rear Safety Belt Comfort Guides for Children and Small Adults Center Passenger Position Children Restraint Systems for Children Older Children Safety Belt Extender Checking Your Restraint Systems Replacing Restraint System Parts After a Crash This part tells you about the power seats how to adjust them and also about reclining front seatbacks lumbar adjustments and heated seats The power seat controls are located on the outboard side of each front seat The knob that controls this feature is located on the outboard side edge of the seat Turn the knob towards the front of the vehicle to increase lumbar support Turn the knob towards the rear of the vehicle to decrease lumbar support To adjust the power s
188. ions Brake linings should always be replaced as complete axle sets See Brake System Inspection in Section 7 of this manual under Part C Periodic Maintenance Inspections Brake Pedal Travel See your dealer if the brake pedal does not return to normal height or if there is a rapid increase in pedal travel This could be a sign of brake trouble Brake Adjustment Every time you apply the brakes with or without the vehicle moving your brakes adjust for wear Replacing Brake System Parts The braking system on a vehicle is complex Its many parts have to be of top quality and work well together if the vehicle is to have really good braking Your vehicle was designed and tested with top quality GM brake parts When you replace parts of your braking system for example when your brake linings wear down and you have to have new ones put in be sure you get new approved GM replacement parts If you don t your brakes may no longer work properly For example if someone puts in brake linings that are wrong for your vehicle the balance between your front and rear brakes can change for the worse The braking performance you ve come to expect can change in many other ways if someone puts in the wrong replacement brake parts Battery Your new vehicle comes with a maintenance free ACDelco battery When it s time for a new battery get one that has the replacement number shown on the original battery s la
189. ior Cleaner and Capture Non Solvent Dry Spot and Soil Remover for cleaning fabric and carpet They will clean normal spots and stains very well You can get GM approved cleaning products from your dealer See Appearance Care and Materials in the Index Here are some cleaning tips Always read the instructions on the cleaner label Clean up stains as soon as you can before they set Carefully scrape off any excess stain Use a clean cloth or sponge and change to a clean area often A soft brush may be used if stains are stubborn If a ring forms on fabric after spot cleaning clean the entire area immediately or it will set Using Multi Purpose Interior Cleaner on Fabric 1 Vacuum and brush the area to remove any loose dirt 2 Always clean a whole trim panel or section Mask surrounding trim along stitch or welt lines 3 Mix powdered cleaner following the directions on the container label to form thick suds 4 Use suds only and apply with a clean sponge Don t saturate the material and don t rub it roughly 5 As soon as you ve cleaned the section use a sponge to remove the suds 6 Wipe cleaned area with a clean damp towel or cloth 7 Wipe with a clean cloth and let dry Special Fabric Cleaning Problems Stains caused by such things as catsup coffee black egg fruit fruit juice milk soft drinks vomit urine and blood can be removed as follows 1 Carefully scrape off excess stain then spon
190. ires are more likely to be cut punctured or broken by a sudden impact such as when you hit a pothole Keep tires at the recommended pressure Worn old tires can cause accidents If your tread is badly worn or if your tires have been damaged replace them Poorly maintained and improperly used tires are dangerous Overloading your tires can cause overheating as a result of too much friction You could have an air out and a serious accident See Loading Your Vehicle in the Index CAUTION Continued 6 48 Inflation Tire Pressure The Tire Loading Information label which is on the rear edge of the driver s door shows the correct inflation pressures for your tires when they re cold Cold means your vehicle has been sitting for at least three hours or driven no more than 1 mile 1 6 km NOTICE Don t let anyone tell you that underinflation or overinflation is all right It s not If your tires don t have enough air underinflation you can get the following Too much flexing Too much heat Tire overloading Bad wear Bad handling Bad fuel economy NOTICE Continued NOTICE Continued If your tires have too much air overinflation you can get the following Unusual wear Bad handling Rough ride Needless damage from road hazards When to Check Check your tires once a month or more Don t forget your compact spare tire It should be at 60 psi 420
191. irp and the exterior lamps may flash depending on the security feedback settings The system should now operate properly 2 14 Trunk It can be dangerous to drive with the trunk lid open because carbon monoxide CO gas can come into your vehicle You can t see or smell CO It can cause unconsciousness and even death If you must drive with the trunk lid open or if electrical wiring or other cable connections must pass through the seal between the body and the trunk lid Make sure all other windows are shut Turn the fan on your heating or cooling system to its highest speed with the setting on any airflow selection except RECIRC That will force outside air into your vehicle See Comfort Controls in the Index If you have air outlets on or under the instrument panel open them all the way See Engine Exhaust in the Index Trunk Lock Release To unlock the trunk from the outside insert the master key and turn it Remote Trunk Release Press the trunk release button located on the lower portion of the driver s door to release the trunk lid The trunk release lockout switch must be OFF for this button to work The system also works with the remote lock control The trunk will unlock when the trunk symbol is pressed while the vehicle is in PARK P or NEUTRAL N and the trunk release lockout switch is in OFF Trunk Release Lockout The trunk release lockout switch in the glove box allows y
192. is equipment PASS Key III uses a radio frequency transponder in the key that matches a decoder in your vehicle When the PASS Key III system senses that someone is using the wrong key it shuts down the vehicle s starter and fuel systems The starter will not work and fuel will stop being delivered to the engine Anyone using a trial and error method to start the vehicle will be discouraged because of the high number of electrical key codes When trying to start the vehicle if the engine does not start and the SECURITY light comes on the key may have a damaged transponder Turn the ignition off and try again If the engine still does not start and the key appears to be undamaged try another ignition key At this time you may also want to check the fuse see Fuses and Circuit Breakers in the Index If the engine still does not start with the other key your vehicle needs service If your vehicle does start the first key may be faulty See your dealer or a locksmith who can service the PASS Key III to have a new key made It is possible for the PASS Key III decoder to learn the transponder value of a new or replacement key Up to 10 keys may be programmed for the vehicle This procedure is for learning additional keys only If all the currently programmed keys are lost or do not operate you must see your dealer or a locksmith who can service PASS Key III to have keys made and programmed to the system See your dealer
193. l circuit breaker and a fuse If the motor overheats due to heavy snow etc the wiper will stop until the motor cools If the overload is caused by some electrical problem have it fixed Power Windows and Other Power Options Circuit breakers in the fuse panel protect the power windows and other power accessories When the current load is too heavy the circuit breaker opens and closes protecting the circuit until the problem is fixed 6 67 Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses and circuit breakers This greatly reduces the chance of fires caused by electrical problems Look at the silver colored band inside the fuse If the band is broken or melted replace the fuse Be sure you replace a bad fuse with a new one of the identical size and rating If a MaxiFuse should blow see your dealer for service immediately If you ever have a problem on the road and don t have a spare fuse you can borrow one that has the same amperage Pick some feature of your vehicle that you can get along without like the radio or cigarette lighter and use its fuse if it is the correct amperage Replace it as soon as you can You will find a fuse puller clipped in both of the bussed electrical centers Snap the wide end of the fuse puller at the side indentations and pull the fuse out The MaxiFuses are located in two Bussed Electrical Centers BEC
194. l other work stopped while headlamp aiming is being done The vehicle should be normally loaded with a full tank of fuel and one person or 160 Ibs 75 kg on the driver s seat Tires should be properly inflated Headlamp aiming is done with the vehicle low beam lamps The high beam lamps will be correctly aimed if the low beam lamps are aimed properly The headlamp aiming devices are under the hood near the headlamps If you believe your headlamps need horizontal left right adjustment follow the horizontal aiming procedure If you believe your headlamps need only vertical up down adjustment follow only the vertical aiming procedure Adjustment screws can be turned with an E8 Torx socket or T15 Torx screwdriver Turn the horizontal aiming screw A until the indicator B is lined up with zero Once the horizontal aim is adjusted then adjust the vertical aim Headlamp Vertical Aiming 1 Find the aim dot on the lens of the lamps 2 Measure the distance from the ground to the aim dot on each lamp if left low beam subtract two inches Record this distance 6 42 3 Atthe wall or other flat surface measure from the floor to the recorded distance and draw a horizontal line the width of the vehicle 4 Turn on the low beam headlamps and cover the lamp 5 Turn the vertical aiming screw C until the not being evaluated The ambient light should allow headlamp beam is aimed to the horizontal li
195. lade or something else sharp on the inside of the rear window If you do you could cut or damage the warming grid and the repairs wouldn t be covered by your warranty Passenger Temperature Control Option With this feature the right front seat passenger can control the comfort setting for their own zone To use this feature turn the knob on the passenger s door to a cooler or warmer setting The temperature can be set up to 8 F 4 C cooler or warmer than the main setting Ventilation System Your vehicle s flow through ventilation system always allows filtered outside air to flow through your vehicle when it is moving even when the system is off The direction of the air can be controlled by adjusting or closing the outlets in the instrument panel Turn the thumbwheel between the front outlets to open and close the outlets Adjust the direction of airflow from side to side with the controls in each outlet Turn the control between the rear outlets up to direct air through the upper outlets Turn the control down to direct air through the lower outlets Adjust the direction of airflow from side to side with the controls in each outlet Ventilation Tips Keep the hood and front air inlet area between the base of the windshield and the hood free of ice snow or any other obstruction such as leaves The defroster and heater will work far better reducing the chance of fogging the inside of your win
196. lamps on when the air information about the readiness of the system when bags inflate if battery power is available You can lock the system commands air bag inflation and driver s the doors again and turn the interior lamps off by using safety belt usage at deployment Some modules also the door lock and interior lamp controls record speed engine rpm brake and throttle data Let only qualified technicians work on your air bag systems Improper service can mean that an air bag system won t work properly See your dealer for service 1 28 lll NOTICE If you damage the covering for the driver s or the right front passenger s air bag or the air bag covering on the driver s and right front passenger s seatback the bag may not work properly You may have to replace the air bag module in the steering wheel both the air bag module and the instrument panel for the right front passenger s air bag or both the air bag module and seatback for the driver s and right front passenger s side impact air bag Do not open or break the air bag coverings Servicing Your Air Bag Equipped Vehicle Air bags affect how your vehicle should be serviced There are parts of the air bag systems in several places around your vehicle Your dealer and the service manual have information about servicing your vehicle and the air bag systems To purchase a service manual see Service and Owner Publications in the Index For up to 10
197. le use the red and blue buttons located below the digital display If you want a warmer comfort level push the red button If you want a cooler comfort level push the blue button Your selected comfort setting will be shown on the digital display for five seconds then the outside temperature will be displayed Mode Control Turn the AUTO PUSH knob to deliver air through the floor panel or windshield outlets The system will stay in the selected mode until the AUTO PUSH knob is pressed AUTO FAN Knob This knob controls the fan speed in either an automatic mode or a manual mode Pressing the AUTO FAN knob puts the fan control in the automatic mode The AUTO FAN light will appear below the knob The fan speed indicators will not be illuminated when the system is in the automatic fan control mode Turning the AUTO FAN knob selects a manual fan speed Turn this knob clockwise to raise the fan speed Turn this knob counterclockwise to lower the fan speed Turning the AUTO FAN knob overrides the automatic fan control mode The fan speed indicators will be illuminated while in the manual fan control mode Automatic Operation Press the AUTO PUSH knob when you want the system to automatically adjust the interior temperature to your preference When the system is set for automatic operation air will come from the floor the panel outlets or the windshield outlets depending on the temperature inside the vehicle the outside temper
198. le scanning The SCAN icon will be lit and a D will blink to indicate disc scan mode Press SEEK again to stop DISC SCAN TP CD Press this button to play a CD if you have a magazine loaded in the changer and the radio is playing To return to the radio while a CD is playing press AM FM You can also press this button to switch between a cassette tape CD or the CD changer if all three are loaded 3 23 Theft Deterrent Feature THEFTLOCK is designed to discourage theft of your radio It works by using a secret code to disable all radio functions whenever battery power is removed and the radio is placed in a different vehicle This feature requires no user input to be activated It is automatically armed when it is put into the vehicle for the first time When the radio is turned off the blinking red light indicates that THEFTLOCK is armed If THEFTLOCK is activated your radio will not operate if stolen The radio will display LOC and a red LED indicator light will come on above the THEFTLOCK logo to indicate a locked condition If this occurs the radio will have to be returned to the dealer Audio Steering Wheel Controls With this feature you can control certain radio functions using the buttons on your steering wheel 3 24 Some steering wheel controls operate climate controls See Steering Wheel Controls for Climate Control earlier in this section VOL Press the up or down arrow to increase or de
199. lectrochromic inside rearview mirror with a compass Your vehicle s mirror may also contain OnStar controls This is the on off button for mirrors equipped with OnStar controls Pressing the MIRROR button or the on off button for mirrors equipped with OnStar controls located at the bottom of the mirror turns the automatic dimming feature on or off The mirror also includes an eight point compass display in the upper right corner of the mirror face When on the compass automatically calibrates as the vehicle is driven When cleaning the mirror use a paper towel or similar material dampened with glass cleaner Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing 2 50 Mirror Operation To turn on the automatic dimming feature press MIRROR or press and hold the on off button for about three seconds for mirrors equipped with OnStar controls To turn off automatic dimming press MIRROR or press and hold the on off button for about three seconds for mirrors equipped with OnStar controls again The green indicator light will be illuminated when this feature is active The automatic dimming feature will be active each time the vehicle is started Compass Operation Press COMPASS or the on off button for mirrors equipped with OnStar controls once to turn the compass on or off When the ignition and the compass feature are on the compass will show two c
200. left the engine running the vehicle can move suddenly You or others could be injured To be sure your vehicle won t move even when you re on fairly level ground always set your parking brake and move the shift lever to PARK P Follow the proper steps to be sure your vehicle won t move See Shifting Into PARK P in the Index If you are parking on a hill and if you re pulling a trailer also see Towing a Trailer in the Index 2 34 Horn Press on the center area of the steering wheel to sound the horn Tilt Wheel A tilt steering wheel allows you to adjust the steering wheel before you drive You can also raise it to the highest level to give your legs more room when you exit and enter the vehicle To tilt the wheel hold the steering wheel and pull the lever toward you Move the steering wheel to a comfortable level then release the lever to lock the wheel in place Turn Signal Multifunction Lever Turn and Lane Change Signals The turn signal has two upward for right and two downward for left positions These positions allow you to signal either a turn or a lane change To signal a turn move the lever all the way up or down When the turn is finished the lever will return automatically An arrow on the instrument panel cluster will flash in the direction of the turn or lane change The lever on the left side of the steering column includes the following Turn and Lane Ch
201. les To request an order form please specify year and model name of the vehicle OR ORDER TOLL FREE 1 800 551 4123 Monday Friday 8 00 AM 6 00 PM Eastern Time For Credit Card Orders Only VISA MasterCard Discover ORDER TOLL FREE NOTE For Credit Card Holders Only 1 800 551 4123 Monday Friday 8 00 AM 6 00 PM EST FAX Orders Only 1 313 865 5927 NOTE Dealers and Companies please provide dealer or company name and also the name of the person to whose attention the shipment should be sent Mail completed order form to HELM INCORPORATED e P O Box 07130 Detroit MI 48207 For purchases outside U S A please write to the above address for quotation CUSTOMER S NAME ATTENTION STREET ADDRESS NO P O BOX NUMBERS CITY STATE ZIP CODE DAYTIME TELEPHONE NO AREA CODE Orders will be mailed within 10 days of receipt Please allow adequate time for postal service If further information is needed write to the address shown below or call 1 800 551 4123 Material cannot be returned for credit without packing slip with return information within 30 days of delivery On returns a re stocking fee may be applied against the original order Check or Money Order payable to Helm Inc USA funds only do not send cash L MasterCard Michigan Purchasers add 6 sales tax U S Order Processing 6 00 Canadian Postage C See Note Below C Discover Number att Check here if your billing a
202. ling 1 800 833 OLDS 6537 TTY users in Canada can dial 1 800 263 3830 Customer Assistance Offices Oldsmobile encourages customers to call the toll free number for assistance If a U S customer wishes to write to Oldsmobile the letter should be addressed to Oldsmobile s Customer Assistance Network United States Customer Assistance Representative Oldsmobile Customer Assistance Network 16 E Judson Street P O Box 436006 Pontiac MI 48343 6006 1 800 442 6537 1 800 833 6537 For Text Telephone devices TTYs Roadside Assistance 1 800 442 OLDS 6537 Canada General Motors of Canada Limited Customer Communication Centre 163 005 1908 Colonel Sam Drive Oshawa Ontario L1H 8P7 1 800 263 3777 English 1 800 263 7854 French 1 800 263 3830 For Text Telephone devices TTYs Roadside Assistance 1 800 268 6800 All Overseas Locations GMODC Customer Communication Centre 169 007 1908 Colonel Sam Drive Oshawa Ontario L1H 8P7 Telephone 905 644 4112 Fax 905 644 4866 Caribbean Numbers 1 800 496 9992 English Puerto Rico 1 800 496 9993 Spanish Puerto Rico 1 800 751 4135 English Dominican Republic 1 800 751 4136 Spanish Dominican Republic 1 800 496 9994 U S Virgin Islands 1 800 389 0009 Bahamas 1 800 534 0122 Bermuda Barbados Antigua amp B V I If toll free service is not available in the Caribbean call Puerto Rico 1 787 763 1315 GM Mobility Program for Persons with Disabilities
203. lockwise on the jack Raise the vehicle far enough off the ground so there s enough room for the spare tire to fit Remove all the wheel nuts and take off the flat tire 7 Remove any rust or dirt from the wheel bolts mounting surfaces and spare wheel Rust or dirt on the wheel or on the parts to which it is fastened can make the wheel nuts become loose after a time The wheel could come off and cause an accident When you change a wheel remove any rust or dirt from the places where the wheel attaches to the vehicle In an emergency you can use a cloth or a paper towel to do this but be sure to use a scraper or wire brush later if you need to to get all the rust or dirt off Never use oil or grease on studs or nuts If you do the nuts might come loose Your wheel could fall off causing a serious accident 5 23 8 Place the spare tire on the wheel mounting surface P aa Put the wheel nuts back on with the rounded end of the nuts toward the wheel Tighten each nut by hand until the wheel is held against the hub If a nut cannot be tightened by hand use the wheel wrench and see your dealer right away 5 24 10 Lower the vehicle by turning the wheel wrench counterclockwise on the jack Lower the jack completely 11 Using the wheel wrench tighten the wheel nuts firmly in a crisscross sequence as shown Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to
204. low the hips just touching the top of the thighs It should never be worn over the abdomen which could cause severe or even fatal internal injuries in a crash Accident statistics show that children are safer if they are restrained in the rear seat In a crash children who are not buckled up can strike other people who are buckled up or can be thrown out of the vehicle Older children need to use safety belts properly Never do this Here two children are wearing the same belt The belt can t properly spread the impact forces In a crash the two children can be crushed together and seriously injured A belt must be used by only one person at a time 1 55 Q What if a child is wearing a lap shoulder belt A but the child is so small that the shoulder belt is very close to the child s face or neck Move the child toward the center of the vehicle but be sure that the shoulder belt still is on the child s shoulder so that in a crash the child s upper body would have the restraint that belts provide If the child is sitting in a seat next to a window move the child toward the center of the vehicle If the child is sitting in the center rear seat passenger position with a lap shoulder belt move the child toward the safety belt buckle In either case be sure that the shoulder belt still is on the child s shoulder so that in a crash the child s upper body would have the restraint that belts provide If the
205. ls 3 11 AM FM Stereo with Cassette Tape and 3 2 Automatic Electronic Climate Control Compact Disc Player with Programmable 3 6 Air Conditioning Equalization and Radio Data System RDS 3 7 Heating 3 20 Trunk Mounted CD Changer Option 3 7 Defogging and Defrosting 3 24 Theft Deterrent Feature 3 8 Rear Window Defogger 3 24 Audio Steering Wheel Controls 3 8 Passenger Temperature Control Option 3 25 Understanding Radio Reception 3 9 Ventilation System 3 25 Tips About Your Audio System 3 10 Steering Wheel Controls for Climate Control 3 26 Care of Your Cassette Tape Player 3 10 Audio Systems 3 27 Care of Your Compact Discs 3 10 Setting the Clock 3 27 Care of Your Compact Disc Player 3 27 Diversity Antenna System 3 28 Chime Level Adjustment Comfort Controls This section tells you how to operate your climate control system Your vehicle may be equipped with a passenger compartment air filter For more information see Passenger Compartment Air Filter in the Index Comfort Controls Personalization If Equipped This feature allows two different drivers to store and recall their own climate control settings for temperature air delivery mode and fan speed The personal choice settings recalled are determined by the transmitter used to enter the vehicle After the button with the unlock symbol on a remote keyless entry transmitter is pressed and the ignition is in RUN the climate control will adjust to the last settings of the identifie
206. m Hearing damage from loud noise is almost undetectable until it is too late Your hearing can adapt to higher volumes of sound Sound that seems normal can be loud and harmful to your hearing Take precautions by adjusting the volume control on your radio to a safe sound level before your hearing adapts to it To help avoid hearing loss or damage e Adjust the volume control to the lowest setting Increase volume slowly until you hear comfortably and clearly NOTICE Before you add any sound equipment to your vehicle like a tape player CB radio mobile telephone or two way radio be sure you can add what you want If you can it s very important to do it properly Added sound equipment may interfere with the operation of your vehicle s engine Delphi Delco Electronics radio or other systems and even damage them Your vehicle s systems may interfere with the operation of sound equipment that has been added improperly So before adding sound equipment check with your dealer and be sure to check Federal rules covering mobile radio and telephone units 3 25 Care of Your Cassette Tape Player A tape player that is not cleaned regularly can cause reduced sound quality ruined cassettes or a damaged mechanism Cassette tapes should be stored in their cases away from contaminants direct sunlight and extreme heat If they aren t they may not operate properly or may cause failure of the tape player Your tap
207. m can alert you about a low tire but it doesn t replace normal tire maintenance See Tires in the Index When the LOW TIRE PRESSURE message appears on the Driver Information Center you should stop as soon as you can and check all your tires for damage If a tire is flat see If a Tire Goes Flat in the Index Also check the tire pressure in all four tires as soon as you can See Inflation Tire Pressure in the Index Any time you adjust a tire s pressure or have one or more tires repaired or replaced you ll need to reset calibrate the check tire pressure system You ll also need to reset the system whenever you rotate the tires buy new tires install or remove the compact spare and whenever the vehicle s battery has been disconnected Don t reset the check tire pressure system without first correcting the cause of the problem and checking and adjusting the pressure in all four tires If you reset the system when the tire pressures are incorrect the check tire pressure system will not work properly and may not alert you when a tire is low or high To reset calibrate the system 1 Turn the ignition switch to RUN 2 Press the SELECT right arrow button on the DIC until you enter the GAGE mode Then press the SELECT down arrow until TIRE PRESSURE appears on the display 3 Press and hold the DIC RESET button for about five seconds After five seconds the display will show TIRE PRESSURE RESET If TIR
208. m is divided into two parts If one part isn t working the other part can still work and stop you For good braking though you need both parts working well If the warning light comes on there is a brake problem Have your brake system inspected right away QOC Canada BRAKE United States This light should come on briefly when you turn the ignition key to RUN If it doesn t come on then have it fixed so it will be ready to warn you if there s a problem If the light comes on while you are driving pull off the road and stop carefully You may notice that the pedal is harder to push Or the pedal may go closer to the floor It may take longer to stop If the light is still on have the vehicle towed for service See Towing Your Vehicle in the Index 2 69 Your brake system may not be working properly if the brake system warning light is on Driving with the brake system warning light on can lead to an accident If the light is still on after you ve pulled off the road and stopped carefully have the vehicle towed for service When the ignition is on the brake system warning light will also come on when you set your parking brake The light will stay on if your parking brake doesn t release fully If you try to drive off with the parking brake set a chime will also come on until you release the parking brake If the light stays on after your parking brake is fully released it means you have a brak
209. may be warm but not too hot to touch There will be some smoke and dust coming from the vents in the deflated air bags Air bag inflation doesn t prevent the driver from seeing or being able to steer the vehicle nor does it stop people from leaving the vehicle 1 27 In many crashes severe enough to inflate an air bag windshields are broken by vehicle deformation Additional windshield breakage may also occur from the right front passenger air bag When an air bag inflates there is dust in the air This dust could cause breathing problems for people with a history of asthma or other Air bags are designed to inflate only once After an air bag inflates you ll need some new parts for your air bag system If you don t get them the air bag system won t be there to help protect you in another crash A new system will include air bag modules breathing trouble To avoid this everyone in the vehicle should get out as soon as it is safe to do so If you have breathing problems but can t get out and possibly other parts The service manual for your of the vehicle after an air bag inflates then get vehicle covers the need to replace other parts fresh air by opening a window or a door Your vehicle is equipped with a crash sensing and diagnostic module which records information about Your vehicle has a feature that will automatically unlock the frontal air bag system The module records the doors and turn the interior
210. ment air filter If you drive regularly under dust ACTUAL conditions the filter may require replacement more often Inspect throttle body bore and valve plates for deposits open the throttle valve and inspect all surfaces Clean as required An Emission Control Service See footnote Replace engine air cleaner filter An Emission Control Service Rotate tires See Tire Inspection and Rotation in the Index for proper rotation pattern and additional information See footnote 7 13 Scheduled Maintenance 97 500 Miles 162 500 km Rotate tires See Tire Inspection and Rotation in the Index for proper rotation pattern and additional information See footnote 100 000 Miles 166 000 km Replace spark plugs An Emission Control Service Change automatic transaxle fluid and bottom screens if the vehicle is mainly driven under one or more of these conditions In heavy city traffic where the outside temperature regularly reaches 90 F 32 C or higher Inhilly or mountainous terrain When doing frequent trailer towing Uses such as found in taxi police or delivery service If you haven t used your vehicle under severe service conditions listed previously and therefore haven t changed your automatic transaxle fluid change both the fluid and filter 150 000 Miles 240 000 km Drain flush and refill cool
211. moving vehicle too rapidly Even though the brake lamps are not flashing it may be slowing down or starting to turn If you re being passed make it easy for the following driver to get ahead of you Perhaps you can ease a little to the right Loss of Control Let s review what driving experts say about what happens when the three control systems brakes steering and acceleration don t have enough friction where the tires meet the road to do what the driver has asked In any emergency don t give up Keep trying to steer and constantly seek an escape route or area of less danger Skidding Ina skid a driver can lose control of the vehicle Defensive drivers avoid most skids by taking reasonable care suited to existing conditions and by not overdriving those conditions But skids are always possible The three types of skids correspond to your vehicle s three control systems In the braking skid your wheels aren t rolling In the steering or cornering skid too much speed or steering in a curve causes tires to slip and lose cornering force And in the acceleration skid too much throttle causes the driving wheels to spin A cornering skid is best handled by easing your foot off the accelerator pedal Remember Any traction control system helps avoid only the acceleration skid If your traction control system is off then an acceleration skid is also best handled by easing your foot off the accelerator pedal
212. mple These symbols These symbols These symbols These symbols Here are some these symbols are important have to do with are on some of are used on other symbols are used on an for you and your lamps your controls warning and you may see original battery your passengers indicator lights whenever your Pe MASTER SJ WINDSHIELD CAUTION Na s LIGHTING O me KZ POSSIBLE i SWITCH NAS ENGINE A INJURY A COOLANT m E ee seed TEMP G3 DOOR LOCK CAUSTIC BATTERY FASTEN ACID COULD w SEAT CAUSE BELTS PROTECT UNLOCK EYES BY BATTERY a ana SHIELDING LIGHTER CHARGING PARKING M SYSTEM LAMPS winpsHIELD nonnes DEFROSTER BRAKE HAZARD WARNING FLASHER REAR GH COOLANT al FUEL TURN WINDSHIELD grrr P SIGNALS WASHERS i7 LI BURNS AVOID SPARKS OR FLAMES WINDOW DAYTIME RUNNING O LAMPS VENTILATING FOG LAMPS x FAN ENGINE OIL OWNER S aa T MANUAL Cli ANTI LOCK es SERVICE BRAKES MANUAL SPARKOR ili FLAME ras NA EXPLODE AIR BAG BATTERY POWER aa DEFOGGER EZ 3 TX LL Service Station Guide Windshield Washer Tire Pressure Fluid See Section 6 For a More See Section 6 Cooling System Battery Detailed Look at See Section 5 See Section 6 What s Under the Hood See Section 6 Spare Tire Pressure 3 See Section 5 Alternate Fuel Door Release Hood Release A See Section 6 See Section 6 Engine Oil Dipstick N Oil Viscosity See Sect
213. n a cassette tape is playing Press TP CD to switch between the tape and compact disc if both are loaded The inactive tape or CD will remain safely inside the radio for future listening The display will show TAPE and CD icons If you have the optional CD changer and the CD changer is loaded the TP CD button will activate the changer and an icon will be lit in the display EJECT Press this button to remove the disc The radio will play EJECT may be activated with either the ignition or radio off CDs may be loaded with the radio and ignition off if this button is pressed first 3 19 Trunk Mounted CD Changer Option mi A Tii amih With the optional compact disc changer you can play up to 12 discs continuously Normal size discs may be You must first load the magazine with discs before you played using the trays supplied in the magazine can play a compact disc Each of the 12 trays holds one disc Load the trays from top to bottom placing a disc on the tray label side up If you load a disc label side down the disc will not play and an error will occur Gently push the tray back into the magazine slot until it locks into place Repeat this procedure for loading up to 12 discs in the magazine 3 20 Once you have loaded the discs in the magazine slide open the door of the compact disc CD changer Push the magazine into the changer in the direction of the arrow marked on top of the magazine Close the door by slidin
214. n at the same time During your trip check occasionally to be sure that the load is secure and that the lamps and any trailer brakes are still working Following Distance Stay at least twice as far behind the vehicle ahead as you would when driving your vehicle without a trailer This can help you avoid situations that require heavy braking and sudden turns Passing You ll need more passing distance up ahead when you re towing a trailer And because you re a good deal longer you ll need to go much farther beyond the passed vehicle before you can return to your lane Backing Up Hold the bottom of the steering wheel with one hand Then to move the trailer to the left just move that hand to the left To move the trailer to the right move your hand to the right Always back up slowly and if possible have someone guide you 4 35 Making Turns NOTICE Making very sharp turns while trailering could cause the trailer to come in contact with the vehicle Your vehicle could be damaged Avoid making very sharp turns while trailering When you re turning with a trailer make wider turns than normal Do this so your trailer won t strike soft shoulders curbs road signs trees or other objects Avoid jerky or sudden maneuvers Signal well in advance Turn Signals When Towing a Trailer When you tow a trailer your vehicle may need a different turn signal flasher and or extra wiring Check with your de
215. n each tire s sidewall When you get new tires get ones with that same TPC Spec number That way your vehicle will continue to have tires that are designed to give proper endurance handling speed rating traction ride and other things during normal service on your vehicle If your tires have an all season tread design the TPC number will be followed by an MS for mud and snow If you ever replace your tires with those not having a TPC Spec number make sure they are the same size load range speed rating and construction type bias bias belted or radial as your original tires Mixing tires could cause you to lose control while driving If you mix tires of different sizes or types radial and bias belted tires the vehicle may not handle properly and you could have a crash Using tires of different sizes may also cause damage to your vehicle Be sure to use the same size and type tires on all wheels It s all right to drive with your compact spare though It was developed for use on your vehicle If you use bias ply tires on your vehicle the wheel rim flanges could develop cracks after many miles of driving A tire and or wheel could fail suddenly causing a crash Use only radial ply tires with the wheels on your vehicle 6 53 Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width For example Treadwear 200
216. n fully then lift out the ashtray by pulling on the snuffer To use a lighter push the center all the way in and let it go When it s ready the center will pop back out by itself Pull out the entire unit to use it Sun Visors NOTICE l To block out glare you can swing down the visors You can also remove them from the center mount and swing ee i them to the side while the auxiliary visor remains to while it is heating If you do it won t be able to block glare from the front back away from the heating element when it s ready That can make it overheat damaging the Don t hold a cigarette lighter in with your hand To extend the visor at the sides pull out the extension lighter and the heating element Illuminated Visor Vanity Mirrors When you open the cover to the driver or passenger side The cigarette lighter will only operate when the ignition visor vanity mirror the lamps will come on is in RUN and for 10 minutes after turning the ignition off If you would like the lighter to operate regardless of the ignition position and for unlimited periods of time see Engine Compartment Bussed Electrical Center in the Index or see your dealer Leaving an accessory on for a long period of time can drain the vehicle s battery 2 55 Accessory Power Outlet The accessory power outlet 12 volt is located on the front passenger s side of the vehicle near the floor on the console The outlet can b
217. n securing an add on child restraint refer to the instructions that come with the restraint which may be on the restraint itself or in a booklet or both and to this manual The child restraint instructions are important so if they are not available obtain a replacement copy from the manufacturer Where to Put the Restraint Accident statistics show that children are safer if they are restrained in the rear rather than the front seat General Motors therefore recommends that child restraints be secured in the rear seat including an infant riding in a rear facing infant seat a child riding in a forward facing child seat and an older child riding in a booster seat Never put a rear facing child restraint in the front passenger seat Here s why A child in a rear facing child restraint can be seriously injured or killed if the right front passenger s air bag inflates This is because the back of the rear facing child restraint would be very close to the inflating air bag Always secure a rear facing child restraint in a rear seat You may secure a forward facing child restraint in the right front seat but before you do always move the front passenger seat as far back as it will go It s better to secure the child restraint in a rear seat Wherever you install it be sure to secure the child restraint properly Keep in mind that an unsecured child restraint can move around in a collision or sudden stop and injure people in
218. n the driver s side of the vehicle at the top of the trunk compartment Pull the tab toward you to release the fuel door NOTICE Prying on a locked fuel filler door could damage it Use the remote fuel door manual release located in the trunk While refueling hang the tethered cap from the hook on the fuel door To remove the cap turn it slowly to the left counterclockwise The cap has a spring in it if you let go of the cap too soon it will spring back to the right If you get gasoline on yourself and then something ignites it you could be badly burned Gasoline can spray out on you if you open the fuel filler cap too quickly This spray can happen if your tank is nearly full and is more likely in hot weather Open the fuel filler cap slowly and wait for any hiss noise to stop Then unscrew the cap all the way Be careful not to spill gasoline Clean gasoline from painted surfaces as soon as possible See Cleaning the Outside of Your Vehicle in the Index When you put the cap back on turn it to the right clockwise until you hear a clicking sound Make sure you fully install the cap The diagnostic system can determine if the fuel cap has been left off or improperly installed This would allow fuel to evaporate into the atmosphere See Malfunction Indicator Lamp in the Index The CHECK GAS CAP DIC message will come on if the fuel cap is not properly reinstalled
219. n the following zone map 2 Press and hold COMPASS or the on off button for mirrors equipped with OnStar controls until a zone number appears in the display Once the zone number appears in the display press the COMPASS or the on off button for mirrors equipped with OnStar controls button quickly until the correct zone number appears in the display Stop pressing the button and the mirror will return to normal operation If C appears in the compass window the compass may need calibration See Compass Calibration explained previously 2 51 Power Remote Control Mirror The controls on the driver s door operate both outside rearview mirrors Move the L R switch to the left L to select the driver s side rearview mirror or to the right R to select the passenger s side rearview mirror Then press the arrows on the four way pad to adjust each mirror so that you can see a little of the side of your vehicle when you are sitting in a comfortable driving position 2 52 Leave the L R switch in the center position to disable mirror movement by the four way control pad If your vehicle is equipped with the memory function the mirrors and driver s seat position can be stored into memory See Memory Seat and Mirrors in the Index Parallel Park Assist Mirror If Equipped If you have the memory seat and mirrors feature the passenger s outside rearview mirror also includes a tilt down fe
220. nalization Programming in the Index 2 8 Rear Door Security Lock Your vehicle is equipped with rear door security locks that help prevent passengers from opening the rear doors of your vehicle from the inside To use one of these locks do the following 1 Move the lever all the way up to the ENGAGED position 2 Close the door 3 Repeat Steps 1 and 2 for the other rear door lock The rear doors of your vehicle cannot be opened from inside when this feature is in use If you want to open a rear door when the security lock is on do the following 1 Unlock the door 2 Then open the door from the outside If you don t cancel the security lock feature adults or older children who ride in the rear won t be able to open the rear door from the inside You should let adults and older children know how these security locks work and how to cancel the locks To cancel the rear door lock do the following 1 Unlock the door and open the door from the outside 2 Move the lever all the way down 3 Repeat Steps 1 and 2 for the other rear door The rear door locks will now work normally Anti Lockout Feature The power door locks will not work if the key is in the ignition and any door is open You can override this feature by holding the driver s power door lock switch for more than three seconds Leaving Your Vehicle When you leave the vehicle open your door and set the locks from the inside then get
221. nd radiator hoses and other engine parts can be very hot Don t touch them If you do you can be burned Don t run the engine if there is a leak If you run the engine it could lose all coolant That could cause an engine fire and you could be burned Get any leak fixed before you drive the vehicle If there seems to be no leak with the engine on check to see if the electric engine cooling fans are running If the engine is overheating both fans should be running If they aren t your vehicle needs service NOTICE Engine damage from running your engine without coolant isn t covered by your warranty See Overheated Engine Protection Operating Mode in the Index 5 13 How to Add Coolant to the Coolant Surge Tank If you haven t found a problem yet but the coolant level isn t at at the proper level below the base of the filler neck add a 50 50 mixture of clean drinkable water and DEX COOL coolant at the coolant surge tank but be sure the cooling system including the coolant surge tank pressure cap is cool before you do it See Engine Coolant in the Index for more information Steam and scalding liquids from a hot cooling system can blow out and burn you badly They are under pressure and if you turn the coolant surge tank pressure cap even a little they can come out at high speed Never turn the cap when the CAUTION Continued 5 14 cooling system including the coola
222. nderbody car washing system can do this for you Chemical Paint Spotting Some weather and atmospheric conditions can create a chemical fallout Airborne pollutants can fall upon and attack painted surfaces on your vehicle This damage can take two forms blotchy ringlet shaped discolorations and small irregular dark spots etched into the paint surface Although no defect in the paint job causes this Oldsmobile will repair at no charge to the owner the surfaces of new vehicles damaged by this fallout condition within 12 months or 12 000 miles 20 000 km of purchase whichever occurs first GM Vehicle Care Appearance Materials 1052918 8 oz 0 237 L or All Protectant Protects leather wood acrylics Plexiglas plastic rubber and vinyl 1052925 16 oz 0 473 L Multi Purpose Interior Cleans carpets seats interior trim door panels Cleaner and floor mats See your General Motors Parts Department for these products For exterior use only See Recommended Fluids and Lubricants in the Index Not recommended for use on instrument panels 6 65 Vehicle Identification Number VIN SAMPLE4UXZM072675 au _ Booth a ASSEMBLY MODEL YEAR PLANT ENGINE CODE This is the legal identifier for your vehicle It appears on a plate in the front corner of the instrument panel on the driver s side You can see it if you look through the windshield from outside your vehicle The VIN also appears on the Veh
223. ndows Usage Cigar Rear Defogger MaxiFuses 60 61 62 63 64 65 66 Spare Fuses 67 68 69 70 71 72 73 74 75 Usage Not Used Rear Defog Not Used Audio Amplifier Electronic Level Control ELC Cigar Not Used Usage Not Used Not Used Not Used Spare Spare Spare Spare Spare Fuse Puller Replacement Bulbs EXTERIOR LAMPS BULB Front Front Turn Signal Lamps 3157NA Halogen Headlamps Low Beam sporeste teniri aves ae ewes 9006 High Beam cp sce 4645s wey een ob eves Se 9005 Rear Back Up Lamps ivcnces eh eke mews ake oles 3155 Stop Taillamps 00 00 0005 3057 Rear Turn Signal Lamps 3057 INTERIOR LAMPS BULB Overhead Rail Courtesy Reading Lamps 168 For service information on other bulbs contact your dealer s service department 6 75 Capacities and Specifications The following approximate capacities are given in English and metric conversions Please refer to Recommended Fluids and Lubricants in the Index for more information Engine Code LX5 3 5L V6 Automatic Transaxle Overdrive When draining or replacing torque converter more fluid may be needed Pan Removal Drain Plug and Replacement 7 4 quarts 7 0 L After Complete Overhaul 10 0 quarts 9 5 L When performing either transaxle procedure check fluid level when done More fluid may be needed Cooling System 10 0 quarts 9
224. ne It is the beam cut off to be seen on the wall recommended to cover the lamp that is not being evaluated to better see the beam being aimed 6 43 Front Turn Signals and Parking Lamps 1 Remove the two bolts with a 10 mm socket 2 Use a large screwdriver by the outside mount to separate the lamp assembly from the outboard snap mounting pin Slide the headlamp assembly outward and lift it out 6 44 3 Disconnect the wiring harness from the headlamp assembly 4 Tip the headlamp assembly and while pressing the release turn the bulb and socket counterclockwise to remove them 5 Replace the bulb and socket Then reconnect the wiring harness to the lamp assembly Slide the lamp assembly back into place by lining up the track on the bottom of the assembly with the guide on the vehicle Then connect the outboard snap and secure the lamp assembly with the two bolts Rear Turn Signals Stoplamps Taillamps and Back up Lamps For the proper bulb type see Replacement Bulbs in the Index 1 Open the trunk Turn the screws located inside of the trunk counterclockwise and remove them 2 Remove the plastic trim piece from the trunk 3 Pull the carpeting away from the rear corner of the trunk 4 Remove the three 10 mm nuts holding the lamp in place and remove the lamp assembly 5 While pressing the release turn the bulb socket assembly counterclockwise to remove it from the lamp assembly
225. ne Engines starburst symbol Failure to use the recommended oil can result in engine damage not covered by your warranty GM Goodwrench oil meets all the requirements for your vehicle If you are in an area where the temperature falls below 20 F 29 C consider using either an SAE 5W 30 synthetic oil or an SAE OW 30 oil Both will provide easier cold starting and better protection for your engine at extremely low temperatures Engine Oil Additives Don t add anything to your oil The recommended oils with the starburst symbol are all you will need for good performance and engine protection When to Change Engine Oil Your vehicle has a computer that lets you know when to change your engine oil This is not based on mileage but on engine revolutions and engine operating temperature When the computer has calculated that the oil needs changing the GM Oil Life System will indicate that a change is necessary The mileage between oil and filter changes will vary depending on how you drive your vehicle usually between 3 000 miles 5 000 km and 10 000 miles 16 000 km since your last oil and filter change Under severe conditions the system may come on before 3 000 miles 5 000 km Never drive your vehicle more than 10 000 miles 16 000 km or 12 months whichever occurs first without an oil change The system won t detect dust in the oil So if you drive in a dusty area be sure to change your oil and filter
226. ne immediately if it starts 3 Try to start the engine in each gear The starter NOTE Be ready to apply the regular brake should work only in PARK P or NEUTRAL N immediately if the vehicle begins to move If the starter works in any other position your 3 With the engine off turn the key to the RUN vehicle needs service position but don t start the engine Without applying the regular brake try to move the shift lever out of PARK P with normal effort If the shift lever moves out of PARK P your vehicle needs service 7 17 Ignition Transaxle Lock Check While parked and with the parking brake set try to turn the ignition key to LOCK in each shift lever position The key should turn to LOCK only when the shift lever is in PARK P The key should come out only in LOCK Parking Brake and Automatic Transaxle PARK P Mechanism Check When you are doing this check your vehicle could begin to move You or others could be injured and property could be damaged Make sure there is room in front of your vehicle in case it begins to roll Be ready to apply the regular brake at once should the vehicle begin to move 7 18 Park on a fairly steep hill with the vehicle facing downhill Keeping your foot on the regular brake set the parking brake To check the parking brake s holding ability With the engine running and transaxle in NEUTRAL N slowly remove foot pressure from the regular brake pedal
227. ng Uses such as found in taxi police or delivery service If you do not use your vehicle under any of these conditions change the fluid and filter at 100 000 miles 166 000 km See Scheduled Maintenance Services in the Index How to Check Because this operation can be a little difficult you may choose to have this done at the dealership service department If you do it yourself be sure to follow all the instructions here or you could get a false reading on the dipstick NOTICE Too much or too little fluid can damage your transaxle Too much can mean that some of the fluid could come out and fall on hot engine parts or exhaust system parts starting a fire Be sure to get an accurate reading if you check your transaxle fluid 6 23 Wait at least 30 minutes before checking the transaxle fluid level if you have been driving When outside temperatures are above 90 F 32 C e At high speed for quite a while In heavy traffic especially in hot weather While pulling a trailer To get the right reading the fluid should be at normal operating temperature which is 180 F to 200 F 82 C to 93 C Get the vehicle warmed up by driving about 15 miles 24 km when outside temperatures are above 50 F 10 C If it s colder than 50 F 10 C you may have to drive longer Checking the Fluid Level Prepare your vehicle as follows Park your vehicle on a level place Keep the engine
228. ng Make sure your rig will be legal not only where you live but also where you ll be driving A good source for this information can be state or provincial police Consider using a sway control You can ask a hitch dealer about sway controls Don t tow a trailer at all during the first 1 000 miles 1 600 km your new vehicle is driven Your engine axle or other parts could be damaged Then during the first 500 miles 800 km that you tow a trailer don t drive over 50 mph 80 km h and don t make starts at full throttle This helps your engine and other parts of your vehicle wear in at the heavier loads Obey speed limit restrictions when towing a trailer Don t drive faster than the maximum posted speed for trailers or no more than 55 mph 90 km h to save wear on your vehicle s parts 4 32 Three important considerations have to do with weight the weight of the trailer the weight of the trailer tongue and the total weight on your vehicle s tires Weight of the Trailer How heavy can a trailer safely be It should never weigh more than 1000 Ibs 450 kg But even that can be too heavy It depends on how you plan to use your rig For example speed altitude road grades outside temperature and how much your vehicle is used to pull a trailer are all important And it can also depend on any special equipment that you have on your vehicle You can ask your dealer for our trailering inf
229. ng accordingly The light will stay on for a few seconds after the traction control system stops limiting wheel spin 2 71 Engine Coolant Temperature Gage This gage shows the engine coolant temperature If the gage pointer moves into the red warning zone your engine is hot To prevent engine overheating the air conditioning compressor will turn off automatically a fast pulsed chime will sound and the message ENGINE HOT A C OFF will appear in the Driver Information Center DIC As the engine cools down the air conditioning compressor will automatically turn back on 2 72 If the coolant temperature is over 262 F 128 C the message HOT IDLE ENGINE will appear It means you should reduce the engine load and speed to prevent the engine from overheating If the coolant temperature is over 268 F 131 C the message HOT STOP ENGINE will appear It means that your engine coolant has overheated You should pull off the road stop your vehicle and turn off the engine as soon as possible Your vehicle is equipped with an Overheated Engine Protection Operating Mode See Engine Overheating in the Index for more information If your coolant level is low the message LOW ENGINE COOLANT will appear on the Driver Information Center Check your coolant level as soon as possible See Engine Coolant in the Index Malfunction Indicator Lamp Check Engine Light C CHECK Your vehicle is equipped
230. ng the signal Take a few steps to the left or right hold the transmitter higher and try again Check to determine if battery replacement or resynchronization is necessary See the instructions that follow If you re still having trouble see your dealer or a qualified technician for service 2 10 Operation The numbers on the back of your transmitter correspond to DRIVER 1 and DRIVER 2 on the DIC For more information see DIC in the Index The driver s door will unlock and the exterior lights will flash twice when the unlock symbol is pressed If the unlock symbol is pressed again within five seconds all doors will unlock the exterior lamps will flash twice and the horn may sound See Security Feedback in the Index Pressing the unlock symbol will also illuminate the interior lamps See Illuminated Entry in the Index All doors will lock the exterior lamps will flash once and the horn may sound when the lock symbol is pressed The trunk will unlock when the trunk symbol is pressed when the ignition is in LOCK The trunk symbol will also work when the ignition is on but only while the transaxle is in PARK P or NEUTRAL N Instant Alarm When the horn symbol on the remote lock control transmitter is pressed the horn will sound and the headlamps and taillamps will flash for up to 30 seconds This can be turned off by pressing the horn symbol again unlocking the vehicle with a
231. nk Transmitter 2 60 Rolling Code Programming If Equipped If you have not previously programmed the hand held transmitter to the HomeLink Transmitter see Programming the HomeLink Transmitter listed previously If you have completed this programming already you now need to train the garage door opener motor head unit to recognize the HomeLink Transmitter Refer to your garage door opener owner s manual for the proper transmitter training procedure for your garage door opener brand 1 Find the training button on the garage door opener motor head unit The exact location and color of the button may vary by garage door opener brand If you have difficulty finding the training button refer to your garage door opener owner s manual 2 Press the training button on the garage door opener motor head unit Following this step you have 30 seconds to start Step 3 3 Return to the HomeLink Transmitter in your vehicle and firmly press and release the HomeLink Transmitter button you have already programmed for two to three seconds Press and release the button again you may need to do this step up to three times to make sure that the HomeLink Transmitter has been trained to the garage door opener motor head unit Check that the training was successful The garage door opener should now recognize the HomeLink Transmitter You may either use the HomeLink Transmitter or the hand held transmitter to open the garage do
232. not be covered by your warranty Pull a trailer only if you have followed all the steps in this section Ask your dealer for advice and information about towing a trailer with your vehicle Your vehicle can tow a trailer if it is equipped with the proper trailer towing equipment To identify what the vehicle trailering capacity is for your vehicle you should read the information in Weight of the Trailer that appears later in this section But trailering is different than just driving your vehicle by itself Trailering means changes in handling durability and fuel economy Successful safe trailering takes correct equipment and it has to be used properly That s the reason for this part In it are many time tested important trailering tips and safety rules Many of these are important for your safety and that of your passengers So please read this section carefully before you pull a trailer Load pulling components such as the engine transaxle wheel assemblies and tires are forced to work harder against the drag of the added weight The engine is required to operate at relatively higher speeds and under greater loads generating extra heat What s more the trailer adds considerably to wind resistance increasing the pulling requirements 4 31 If You Do Decide To Pull A Trailer If you do here are some important points There are many different laws including speed limit restrictions having to do with traileri
233. nt surge tank pressure cap is hot Wait for the cooling system and coolant surge tank pressure cap to cool if you ever have to turn the pressure cap Adding only plain water to your cooling system can be dangerous Plain water or some other liquid like alcohol can boil before the proper coolant mixture will Your vehicle s coolant warning system is set for the proper coolant mixture With plain water or the wrong mixture your engine could get too hot but you wouldn t get the overheat warning Your engine could catch fire and you or others could be burned Use a 50 50 mixture of clean drinkable water and DEX COOL coolant NOTICE In cold weather water can freeze and crack the engine radiator heater core and other parts So use the recommended coolant You can be burned if you spill coolant on hot engine parts Coolant contains ethylene glycol and it will burn if the engine parts are hot enough Don t spill coolant on a hot engine 5 15 2 Then keep turning the pressure cap slowly and remove it 3 Then fill the coolant surge tank with the proper mixture to the base of the filler neck 1 You can remove the coolant surge tank pressure cap when the cooling system including the coolant surge tank pressure cap and upper radiator hose is no longer hot Turn the pressure cap slowly counterclockwise left about one quarter turn and then stop If you hear a hiss wait for that to stop A hiss means t
234. nual that tells how to do it without damaging your vehicle See Towing Your Vehicle in the Index 2 23 Starting Your 4 0L V8 Engine 3 If your engine still won t start or starts but then stops it could be flooded with too much gasoline Try pushing your accelerator pedal all the way to the floor and holding it there as you hold the key in START for about three seconds If the vehicle starts briefly but then stops again do the same thing 1 Without pushing the accelerator pedal turn your ignition key to START When the engine starts let go of the key The idle speed will go down as your engine gets warm NOTICE Holding your key in START for longer than 15 seconds at a time will cause your battery to NOTICE Your engine is designed to work with the electronics in your vehicle If you add electrical parts or accessories you could change the way the engine operates Before adding electrical equipment check with your dealer If you don t your engine might not perform properly be drained much sooner And the excessive heat can damage your starter motor Wait about 15 seconds between each try to help avoid draining your battery or damaging your starter If you ever have to have your vehicle towed 2 If it doesn t start right away hold your key in see the part of this manual that tells how to do START for about three seconds at a time until your it without damaging your vehicle See Towing engine
235. ny one speed fast or slow for the first 500 miles 805 km Don t make full throttle starts Avoid making hard stops for the first 200 miles 322 km or so During this time your new brake linings aren t yet broken in Hard stops with new linings can mean premature wear and earlier replacement Follow this breaking in guideline every time you get new brake linings Don t tow a trailer during break in See Towing a Trailer in the Index for more information Ignition Positions With the ignition key in the ignition switch you can turn the switch to four different positions LOCK A This is the only position in which you can remove the key This position locks your ignition steering wheel and transaxle It s a theft deterrent feature NOTICE If your key seems stuck in LOCK and you can t turn it be sure you are using the correct key if so is it all the way in If it is then turn the steering wheel left and right while you turn the key hard But turn the key only with your hand Using a tool to force it could break the key or the ignition switch If none of this works then your vehicle needs service ACCESSORY B This position lets you use your electrical power accessories such as power windows power sunroof option radio and the windshield wipers RUN C This is the position the switch returns to after you start your engine and release the switch This is the position for normal dri
236. o ride in any area of your vehicle that is not equipped with seats and safety belts Be sure everyone in your vehicle is in a seat and using a safety belt properly Your vehicle has a light that comes on as a reminder to buckle up See Safety Belt Reminder Light in the Index In most states and Canadian provinces the law says to wear safety belts Here s why They work You never know if you ll be in a crash If you do have a crash you don t know if it will be a bad one A few crashes are mild and some crashes can be so serious that even buckled up a person wouldn t survive But most crashes are in between In many of them people who buckle up can survive and sometimes walk away Without belts they could have been badly hurt or killed After more than 30 years of safety belts in vehicles the facts are clear In most crashes buckling up does matter a lot Why Safety Belts Work When you ride in or on anything you go as fast as it goes Take the simplest vehicle Suppose it s just a seat on wheels Put someone on it Get it up to speed Then stop the vehicle The rider doesn t stop The person keeps going until stopped by something or the instrument panel In a real vehicle it could be the windshield or the safety belts With safety belts you slow down as the vehicle does You get more time to stop You stop over more distance and your strongest bones take the force
237. o three channels 1 If you have previously programmed a transmitter channel proceed to Step 2 Otherwise hold down the two outside buttons on the HomeLink Transmitter until the indicator light begins to flash rapidly after 20 seconds Then release the buttons This procedure initializes the memory and erases any previous settings for all three channels 2 Decide which one of the three channels you want to program Hold the end of the hand held transmitter about 2 to 5 inches 5 to 13 cm away from the surface of the HomeLink Transmitter so that you can still see the indicator light 3 Using both hands press the hand held transmitter button and the desired button on the HomeLink Transmitter Continue to press both buttons through Step 4 4 Hold down both buttons until you see the indicator light on the HomeLink Transmitter flash slowly and then rapidly The rapid flashing indicates that the HomeLink Transmitter has been programmed Release both buttons once the indicator light starts to flash rapidly If you have trouble programming the HomeLink Transmitter make sure that you have followed the directions exactly as described The HomeLink Transmitter may not work with older garage door openers that do not meet current Federal Consumer Safety Standards If you cannot program the transmitter after repeated attempts refer to Rolling Code Programming later in this section or contact the HomeLink Transmitter manufacturer at
238. obs you can be seriously injured Do your own maintenance work only if you have the required know how and the proper tools and equipment for the job If you have any doubt have a qualified technician do the work If you want to get the service information see Service and Owner Publications in the Index Part B Owner Checks and Services tells you what should be checked and when It also explains what you can easily do to help keep your vehicle in good condition Part C Periodic Maintenance Inspections explains important inspections that your dealer s service department or another qualified service center should perform Part D Recommended Fluids and Lubricants lists some recommended products necessary to help keep your vehicle properly maintained These products or their equivalents should be used whether you do the work yourself or have it done Part E Maintenance Record is a place for you to record and keep track of the maintenance performed on your vehicle Keep your maintenance receipts They may be needed to qualify your vehicle for warranty repairs Part A Scheduled Maintenance Services Using Your Maintenance Schedule We at General Motors want to help you keep your vehicle in good working condition But we don t know exactly how you ll drive it You may drive very short distances only a few times a week Or you may drive long distances all the time in very hot dusty weather
239. obvious way to solve the leading highway safety problem is for people never to drink alcohol and then drive But what if people do How much is too much if the driver plans to drive It s a lot less than many might think Although it depends on each person and situation here is some general information on the problem The Blood Alcohol Concentration BAC of someone who is drinking depends upon four things The amount of alcohol consumed The drinker s body weight The amount of food that is consumed before and during drinking The length of time it has taken the drinker to consume the alcohol According to the American Medical Association a 180 1b 82 kg person who drinks three 12 ounce 355 ml bottles of beer in an hour will end up with a BAC of about 0 06 percent The person would reach the same BAC by drinking three 4 ounce 120 ml glasses of wine or three mixed drinks if each had 1 1 2 ounces 45 ml of a liquor like whiskey gin or vodka It s the amount of alcohol that counts For example if the same person drank three double martinis 3 ounces or 90 ml of liquor each within an hour the person s BAC would be close to 0 12 percent A person who consumes food just before or during drinking will have a somewhat lower BAC level There is a gender difference too Women generally have a lower relative percentage of body water than men 4 4 Since alcohol is carried in body water this means
240. on Center DIC for two seconds The display in the DIC will also change from an English to a metric display To return to an English display repeat the above procedure Manual Operation You may override the automatic airflow distribution by turning the AUTO PUSH knob After you turn this knob the comfort setting will be displayed for five seconds then the outside temperature will be displayed The fan control will remain in the automatic control mode unless you turn the AUTO FAN knob to select a manual fan speed Pe PANEL This setting directs airflow through the upper air outlets located in the instrument panel lpi BI LEVEL This setting directs the airflow through both the panel air outlets and the lower floor outlets There is also a small amount of air directed to the front defroster and the side window defrosters e ed FLOOR This setting directs most of the airflow to the lower floor outlets with some airflow directed to the side window defrosters There is also a small amount of airflow directed to the front defroster ay DEFOG This setting di jori This setting directs the majority of the airflow to the lower floor outlets and the front defroster A small amount of airflow is directed to the side window defroster outlets This mode can be useful to remove the moisture from the inside of the windshield when the outside temperature is cold or the humidity is high Be sure the A C indicator light comes on to all
241. on The path of an inflating air bag must be kept clear Don t put anything between an occupant and an air bag and don t attach or put anything on the steering wheel hub or on or near any other air bag covering and don t let seat covers block the inflation path of a side impact air bag The right front passenger s side impact air bag is in the side of the passenger s seatback closest to the door 1 25 When should an air bag inflate The driver s and right front passenger s frontal air bags are designed to inflate in moderate to severe frontal or near frontal crashes The frontal air bags are designed to inflate only if the impact speed is above the system s designed threshold level If your vehicle goes straight into a wall that doesn t move or deform the threshold level is about 11 to 16 mph 18 to 26 km h The threshold level can vary however with specific vehicle design so that it can be somewhat above or below this range If your vehicle strikes something that will move or deform such as a parked car the threshold level will be higher The driver s and right front passenger s frontal air bags are not designed to inflate in rollovers side impacts or rear impacts because inflation would not help the occupant The side impact air bags are designed to inflate in moderate to severe side crashes involving a front door A side impact air bag will inflate if the crash severity is above the system
242. on parts as well as open seams holes loose connections or other conditions which could cause a heat build up in the floor pan or could let exhaust fumes into the vehicle See Engine Exhaust in the Index 7 19 Engine Cooling System Inspection Inspect the hoses and have them replaced if they are cracked swollen or deteriorated Inspect all pipes fittings and clamps replace as needed Clean the outside of the radiator and air conditioning condenser To help ensure proper operation a pressure test of the cooling system and pressure cap is recommended at least once a year Throttle System Inspection Inspect the throttle system for interference or binding and for damaged or missing parts Replace parts as needed Replace any components that have high effort or excessive wear Do not lubricate accelerator and cruise control cables 7 20 Brake System Inspection Inspect the complete system Inspect brake lines and hoses for proper hook up binding leaks cracks chafing etc Inspect disc brake pads for wear and rotors for surface condition Inspect other brake parts including calipers parking brake etc You may need to have your brakes inspected more often if your driving habits or conditions result in frequent braking Part D Recommended Fluids and Lubricants NOTE Fluids and lubricants identified below by name part number or specification may be obtained from your dealer USAGE FLUID LUBRICANT Engine Oil
243. one located near the engine compartment on the passenger s side and the other under the rear seat on the driver s side If a MaxiFuse should blow have your vehicle serviced by your dealer immediately 6 68 Engine Compartment Bussed Electrical Center BEC The front Bussed Electrical Center BEC is located in the front of the engine compartment on the passenger s side Lift the cover to gain access See Engine Compartment Overview in the Index for more information on location Fuse 22 or 23 can be moved to the outer position to provide continuous power to the accessory power outlet or cigarette lighter when the ignition is not ON See your dealer for additional assistance if needed Leaving an accessory on for a long period of time can drain the vehicle s battery 2 2 24 B32 sz 31 30 40 9 a o 9 Minifuse 1 o nuy DAURA UN Usage Not Used Accessory Windshield Wipers Not Used Left Low Beam Headlamp Right Low Beam Headlamp Instrument Panel Powertrain Control Module Battery Minifuse 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Usage Right High Beam Headlamp Left High Beam Headlamp Ignition 1 Not Used Transaxle Cruise Control Direct Ignition System Injector Bank 2 Not Used Not Used Powertrain Control Module Ignition Oxygen Sensor Injector B
244. or If after following these instructions you still have problems training the garage door opener contact the HomeLink Transmitter manufacturer at 1 800 355 3515 Erasing Channels To erase all three programmed channels hold down the two outside buttons until the indicator light begins to flash after 20 seconds Release both buttons Accessories Accessories for the HomeLink Transmitter are available from the manufacturer of the unit If you would like additional information please call 1 800 355 3515 2 61 The Instrument Panel Your Information System The main components of your instrument panel are Air Outlet Turn Signal Multifunction Lever Steering Wheel Controls for Climate Control System Steering Wheel Controls for Audio System Windshield Wiper Washer Control Driver Information Center DIC Hazard Warning Flasher Button Climate Control System Tranmmoodndw gt Instrument Panel Brightness Control Ono Be AS Trip Odometer Buttons Hood Release Parking Brake Cruise Control Lever Ignition Switch Audio System Accessory Power Outlet Glove Box Trunk Release Lockout Switch inside 2 63 Instrument Panel Cluster Your vehicle is equipped with this instrument panel cluster which includes indicator warning lights and gages that are explained on the following pages The instrument panel is designed to let you know at a glance how your vehicle is running You ll kn
245. or a locksmith who can service PASS Key III to get a new blank key that is cut exactly as the current black colored driver s key that operates the system Do not use a gray colored VALET key for this procedure 2 19 To program the new key 1 Insert the current driver s key black in color in the ignition and start the engine If the engine will not start see your dealer for service After the engine has started turn the key to LOCK and remove the key Insert the key to be programmed and turn it to RUN within 10 seconds of removing the previous key The SECURITY telltale light will turn off once the key has been programmed It may not be apparent that the SECURITY light went on due to how quickly the key is programmed Repeat Steps 1 through 4 if additional keys are to be programmed If you are ever driving and the SECURITY light comes on and stays on you will be able to restart your engine if you turn it off Your PASS Key III system however is not working properly and must be serviced by your dealer Your vehicle is not protected by the PASS Key III system at this time If you lose or damage a PASS Key III key see your dealer or a locksmith who can service PASS Key III to have a new key made 2 20 New Vehicle Break In NOTICE Your vehicle doesn t need an elaborate break in But it will perform better in the long run if you follow these guidelines Don t drive at a
246. or braking or even none going down a hill You could crash Always have your engine running and your vehicle in gear when you go downhill Know how to go uphill Drive in the highest gear possible Stay in your own lane when driving on two lane roads in hills or mountains Don t swing wide or cut across the center of the road Drive at speeds that let you stay in your own lane As you go over the top of a hill be alert There could be something in your lane like a stalled car or an accident You may see highway signs on mountains that warn of special problems Examples are long grades passing or no passing zones a falling rocks area or winding roads Be alert to these and take appropriate action Here are some tips for winter driving Have your vehicle in good shape for winter You may want to put winter emergency supplies in your trunk Include an ice scraper a small brush or broom a supply of windshield washer fluid a rag some winter outer clothing a small shovel a flashlight a red cloth and a couple of reflective warning triangles And if you will be driving under severe conditions include a small bag of sand a piece of old carpet or a couple of burlap bags to help provide traction Be sure you properly secure these items in your vehicle Driving on Snow or Ice Most of the time those places where your tires meet the road probably have good traction However if there is snow or ice between your tire
247. orking when the ignition is on and the engine is not running If the light doesn t come on have it repaired This light will also come on during a malfunction in one of two ways e Light Flashing A misfire condition has been detected A misfire increases vehicle emissions and may damage the emission control system on your vehicle Dealer or qualified service center diagnosis and service may be required Light On Steady An emission control system malfunction has been detected on your vehicle Dealer or qualified service center diagnosis and service may be required If the Light Is Flashing The following may prevent more serious damage to your vehicle Reducing vehicle speed Avoiding hard accelerations Avoiding steep uphill grades e If you are towing a trailer reduce the amount of cargo being hauled as soon as it is possible 2 74 If the light stops flashing and remains on steady see If the Light Is On Steady following If the light continues to flash when it is safe to do so stop the vehicle Find a safe place to park your vehicle Turn the key off wait at least 10 seconds and restart the engine If the light remains on steady see If the Light Is On Steady following If the light is still flashing follow the previous steps and drive the vehicle to your dealer or qualified service center for service If the Light Is On Steady You may be able to correct the emission system malfun
248. ormation or advice or you can write us at Customer Assistance Representative Oldsmobile Customer Assistance Network 16 E Judson Street P O Box 436006 Pontiac MI 48343 6006 In Canada write to General Motors of Canada Limited Customer Communication Centre 1908 Colonel Sam Drive Oshawa Ontario L1H 8P7 Weight of the Trailer Tongue The tongue load A of any trailer is an important weight to measure because it affects the total or gross weight of your vehicle The Gross Vehicle Weight GVW includes the curb weight of the vehicle any cargo you may carry in it and the people who will be riding in the vehicle And if you tow a trailer you must add the tongue load to the GVW because your vehicle will be carrying that weight too See Loading Your Vehicle in the Index for more information about your vehicle s maximum load capacity If you re using a weight carrying hitch the trailer tongue A should weigh 10 percent of the total loaded trailer weight B If you have a weight distributing hitch the trailer tongue A should weigh 12 percent of the total loaded trailer weight B After you ve loaded your trailer weigh the trailer and then the tongue separately to see if the weights are proper If they aren t you may be able to get them right simply by moving some items around in the trailer 4 33 Total Weight on Your Vehicle s Tires Be sure your vehicle s tires are inflated to the upper
249. ou Trying to start your vehicle by pushing or pulling it won t work and it could damage your vehicle If you don t follow these steps exactly some or all of these things can hurt you 1 Check the other vehicle It must have a 12 volt 3 Turn off the ignition on both vehicles Unplug battery with a negative ground system unnecessary accessories plugged into the cigarette lighter or accessory power outlet Turn off all lamps that aren t needed as well as radios This will avoid NOTICE sparks and help save both batteries In addition it could save your radio If the other system isn t a 12 volt system with a 4 Open the hoods and locate the other vehicle s battery negative ground both vehicles can be damaged and your vehicle s remote positive jump starting terminal in the box on the passenger side of the engine compartment Your vehicle s battery isn t 2 Get the vehicles close enough so the jumper cables under the hood can reach but be sure the vehicles aren t touching each other If they are it could cause a ground connection you don t want You wouldn t be able to start your vehicle and the bad grounding could damage the electrical systems To avoid the possibility of the vehicles rolling set An electric fan can start up even when the engine the parking brake firmly on both vehicles involved in is not running and can injure you Keep hands the jump start procedure Put an automatic tran
250. ou contact your dealer in the area where you ll be parking your vehicle The dealer can give you the best advice for that particular area 2 25 Automatic Transaxle Operation There are several different positions for your shift lever PARK P This position locks your front wheels It s the best position to use when you start your engine because your vehicle can t move easily 2 26 It is dangerous to get out of your vehicle if the shift lever is not fully in PARK P with the parking brake firmly set Your vehicle can roll Don t leave your vehicle when the engine is running unless you have to If you have left the engine running the vehicle can move suddenly You or others could be injured To be sure your vehicle won t move even when you re on fairly level ground always set your parking brake and move the shift lever to PARK P See Shifting Into PARK P in the Index If you re pulling a trailer see Towing a Trailer in the Index Ensure the shift lever is fully in PARK P before starting the engine Your vehicle has an automatic transaxle shift lock control system You have to fully apply your regular brakes before you can shift from PARK P when the ignition key is in RUN REVERSE R Use this gear to back up NOTICE Shifting to REVERSE R while your vehicle is moving forward could damage your transaxle Shift to REVERSE R only after your vehicle is stopped To rock
251. ou to secure items in the trunk and disable the fuel door release and the HomeLink Transmitter Move the trunk release lockout switch to ON lock the glove box and take the master key and remote lock control transmitter with you Now the remote trunk release button will not open the trunk the fuel door release button will not open the fuel door and the HomeLink Transmitter will not operate 8S Theft Vehicle theft is big business especially in some cities Although your vehicle has a number of theft deterrent features we know that nothing we put on it can make it impossible to steal However there are ways you can help Key in the Ignition If you leave your vehicle with the keys inside it s an easy target for joy riders or professional thieves so don t do it With the ignition off and the driver s door open you ll hear a chime reminding you to remove your key from the ignition and take it with you Always do this Your steering wheel will be locked and so will your ignition and transaxle And remember to lock the doors Parking at Night Park in a lighted spot close all windows and lock your vehicle Remember to keep your valuables out of sight Put them in a storage area or take them with you 2 16 Parking Lots Even if you park in a lot where someone will be watching your vehicle it s still best to lock it up and take your keys But what if you have to leave your ignition key If possible
252. oved driveability and emission control system performance compared to other gasolines Be sure the posted octane for premium is at least 91 at least 89 for middle grade and 87 for regular If the octane is less than 87 you may get a heavy knocking noise when you drive If it s bad enough it can damage your engine If you re using fuel rated at the recommended octane or higher and you hear heavy knocking your engine needs service But don t worry if you hear a little pinging noise when you re accelerating or driving up a hill That s normal and you don t have to buy a higher octane fuel to get rid of pinging It s the heavy constant knock that means you have a problem If your vehicle is certified to meet California Emission Standards indicated on the underhood emission control label it is designed to operate on fuels that meet California specifications If such fuels are not available in states adopting California emissions standards your vehicle will operate satisfactorily on fuels meeting federal specifications but emission control system performance may be affected The malfunction indicator lamp on your instrument panel may turn on and or your vehicle may fail a smog check test See Malfunction Indicator Lamp in the Index If this occurs return to your authorized Oldsmobile dealer for diagnosis to determine the cause of failure In the event it is determined that the cause of the condition is the type o
253. ow the air compressor to come on automatically to help dehumidify the air oy DEF Defrost This setting directs the majority of the airflow to the windshield with some airflow to the side window defrosters and lower floor outlets To increase the fan speed turn the AUTO FAN knob clockwise If defrost is selected from AUTO mode your automatic electronic climate control system will automatically increase the defrost outlet temperature and fan speed For maximum front defrost performance under extreme icing or frosting conditions increase the temperature setting to 90 F 33 C and increase the fan speed to high Even though A C is not selected in front defrost mode the A C compressor will run automatically at temperatures over approximately 40 F 4 C to improve windshield clearing performance This dehumidifies the air to help dry the windshield Even though the compressor may be running the A C indicator light will not come on in front defrost unless you select A C RECIRC Press this button to limit the amount of outside air entering your vehicle This is helpful when you are trying to cool the interior of the vehicle quickly or limit the amount of outside air entering your vehicle for some other reason The RECIRC button and the AUTO PUSH knob may be selected at the same time The system will remain in RECIRC until the ignition is turned off then the system will return back to the previously selected mode RECIRC may be
254. ow how fast you re going how much fuel you re using and many other things you 1 need to drive safely and economically United States version shown Canada similar 2 64 Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour mph and kilometers per hour km h Your odometer shows how far your vehicle has been driven in either miles used in the United States or kilometers used in Canada The speedometer shows a top speed of 140 mph 220 km h This is not intended to be the vehicle s top speed You may wonder what happens if your vehicle needs a new odometer installed If the new one can be set to the mileage total of the old odometer then it must be But if it can t then it s set at zero and a label must be put on the driver s door to show the old mileage reading when the new odometer was installed Trip Odometer Your trip odometer tells you how far you have driven since you last reset it Your vehicle is equipped with two trip odometers A and B Press the TRIP A B button to change which trip odometer is displayed Press the TRIP RESET button to reset the trip odometer that is currently being displayed 2 65 Tachometer The tachometer displays the engine speed in revolutions per minute rpm If your engine speed equals or exceeds the safe limit for operation the message HOT REDUCE ENG RPM is displayed on the Driver Information Cente
255. p of the Instrument Panel Use only mild soap and water to clean the top surfaces of the instrument panel Sprays containing silicones or waxes may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions Cleaning Interior Plastic Components Use only a mild soap and water solution on a soft cloth or sponge Commercial cleaners may affect the surface finish Cleaning Wood Panels Use a clean cloth moistened in warm soapy water use mild dish washing soap Dry the wood immediately with a clean cloth Care of Safety Belts Keep belts clean and dry Do not bleach or dye safety belts If you do it may severely weaken them In a crash they might not be able to provide adequate protection Clean safety belts only with mild soap and lukewarm water Cleaning Glass Surfaces Glass should be cleaned often GM Glass Cleaner or a liquid household glass cleaner will remove normal tobacco smoke and dust films on interior glass See Appearance Care and Materials in the Index Don t use abrasive cleaners on glass because they may cause scratches Avoid placing decals on the inside rear window since they may have to be scraped off later If abrasive cleaners are used on the inside of the rear window an electric defogger element may be damaged Any temporary license should not be attached across the defogger grid Cleaning the Outside of the Windshield
256. p your engine if it overheats and get out of the vehicle until the engine is cool See Overheated Engine Protection Operating Mode in the Index NOTICE If your engine catches fire because you keep driving with no coolant your vehicle can be badly damaged The costly repairs would not be covered by your warranty See Overheated Engine Protection Operating Mode in the Index If No Steam Is Coming From Your Engine If you get an engine overheat warning but see or hear no steam the problem may not be too serious Sometimes the engine can get a little too hot when you Climb a long hill on a hot day Stop after high speed driving Idle for long periods in traffic e Tow a trailer If you get the overheat warning with no sign of steam try this for a minute or so 1 If your air conditioner is on turn it off 2 Turn on your heater to full hot at the highest fan speed and open the window as necessary 3 If you re in a traffic jam shift to NEUTRAL N otherwise shift to the highest gear while driving AUTOMATIC OVERDRIVE D or THIRD 3 If you no longer have the overheat warning you can drive Just to be safe drive slower for about 10 minutes If the warning doesn t come back on you can drive normally If the warning continues pull over stop and park your vehicle right away If there s still no sign of steam idle the engine for three minutes while you re parked If
257. pare tire from the trunk The tools you ll be using include the jack A and the wheel wrench B 5 20 Removing the Wheel Cover Insert the hooked end of the wheel wrench in one of the two small notches in the center cover and pry the cover off Do not drop the cover or lay it face down as it could be scratched or damaged Removing the Flat Tire and Installing the Spare Tire 3 Turn the wheel wrench counterclockwise by hand to lower the jack head until it fits under the vehicle 1 Position the wheel wrench securely over the wheel nuts to loosen but don t remove them 2 Attach the wheel wrench to the bolt on the end of the jack to create a jack handle 5 21 4 Near each wheel well is a notch in the frame to position the jack head Position the jack under the vehicle and raise the jack head until it fits firmly against the sheet metal Do not raise the vehicle yet Put the compact spare near you 5 22 Getting under a vehicle when it is jacked up is dangerous If the vehicle slips off the jack you could be badly injured or killed Never get under a vehicle when it is supported only by a jack Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall To help avoid personal injury and vehicle damage be sure to fit the jack lift head into the proper location before raising the vehicle Raise the vehicle by turning the wheel wrench c
258. per radio reception the antenna connector at the top center of the front windshield and the antenna connector at the top center of the rear window need to be properly attached to the posts on the glass NOTICE Do not try to clear frost or other material from the inside of the rear window with a razor blade or anything else that is sharp This may damage the rear defogger grid and affect your radio s ability to pick up stations clearly The repairs wouldn t be covered by your warranty 3 27 If when you turn on your rear window defogger you hear static on your radio station it could mean that a defogger grid line has been damaged If this is true the grid line must be repaired If you choose to add an aftermarket cellular telephone to your vehicle and the antenna needs to be attached to the glass be sure that you do not damage the grid lines for the AM FM antennas or place the cellular telephone antenna over the grid lines 3 28 Chime Level Adjustment The volume level of the vehicle s chimes can be controlled by the radio To change the volume level press and hold pushbutton 6 with the ignition on and the radio power off The chime volume level will change from the normal level to loud and LOUD will be displayed on the radio To change back to the default or normal setting press and hold pushbutton 6 again The chime level will change from the loud level to normal and NORMAL will be displayed SD Section 4
259. pin the wheels too fast while shifting your transaxle back and forth you can destroy your transaxle For information about using tire chains on your vehicle see Tire Chains in the Index Rocking Your Vehicle To Get It Out First turn your steering wheel left and right That will clear the area around your front wheels You should turn your traction control system off See Traction Control System in the Index Then shift back and forth between REVERSE R and a forward gear spinning the wheels as little as possible Release the accelerator pedal while you shift and press lightly on the accelerator pedal when the transaxle is in gear By slowly spinning your wheels in the forward and reverse directions you will cause a rocking motion that may free your vehicle If that doesn t get you out after a few tries you may need to be towed out If you do need to be towed out see Towing Your Vehicle in the Index 5 29 JD Section 6 Service and Appearance Care Here you will find information about the care of your vehicle This section begins with service and fuel information and then it shows how to check important fluid and lubricant levels There is also technical information about your vehicle and a part devoted to its appearance care 6 2 Service 6 58 Appearance Care 6 3 Fuel 6 58 Cleaning the Inside of Your Vehicle 6 10 Filling a Portable Fuel Container 6 62 Cleaning the Outside of Your Vehicle 6 10 Checking
260. possible with the ends securely fastened Drive slowly and follow the chain manufacturer s instructions If you can hear the chains contacting your vehicle stop and retighten them If the contact continues slow down until it stops Driving too fast or spinning the wheels with chains on will damage your vehicle 6 57 Appearance Care Remember cleaning products can be hazardous Some are toxic Others can burst into flame if you strike a match or get them on a hot part of the vehicle Some are dangerous if you breathe their fumes in a closed space When you use anything from a container to clean your vehicle be sure to follow the manufacturer s warnings and instructions And always open your doors or windows when you re cleaning the inside Never use these to clean your vehicle Gasoline Benzene Naphtha Carbon Tetrachloride Acetone Paint Thinner Turpentine Lacquer Thinner Nail Polish Remover They can all be hazardous some more than others and they can all damage your vehicle too 6 58 Don t use any of these unless this manual says you can In many uses these will damage your vehicle Alcohol Laundry Soap Bleach Reducing Agents Cleaning the Inside of Your Vehicle Use a vacuum cleaner often to get rid of dust and loose dirt Wipe vinyl leather plastic and painted surfaces with a clean damp cloth Cleaning of Fabric Carpet Your dealer has two cleaners Multi Purpose Inter
261. quency or type of occurrence While we hope you never have the occasion to use our service it is added security while traveling for you and your family Remember we re only a phone call away Oldsmobile Roadside Assistance 1 800 442 OLDS 6537 Canadian Roadside Assistance Vehicles purchased in Canada have an extensive roadside assistance program accessible from anywhere in Canada or the United States Please refer to the separate brochure provided by the dealer or call 1 800 268 6800 for emergency services Courtesy Transportation Oldsmobile has always exemplified quality and value in its offering of motor vehicles To enhance your ownership experience we and our participating dealers are proud to offer Courtesy Transportation a customer support program for new vehicles The Courtesy Transportation program is offered to retail purchase lease customers in conjunction with the Bumper to Bumper coverage provided by the New Vehicle Limited Warranty Several transportation options are available when warranty repairs are required This will reduce your inconvenience during watranty repairs Plan Ahead When Possible When your vehicle requires warranty service you should contact your dealer and request an appointment By scheduling a service appointment and advising your service consultant of your transportation needs your dealer can help minimize your inconvenience If your vehicle cannot be scheduled into the service depa
262. quids to blow out and burn you badly Never turn the surge tank pressure cap even a little when the engine and radiator are hot The vehicle must be on a level surface When your engine is cold the coolant level should be at the base of the filler neck The engine coolant surge tank is located on the passenger s side of the engine compartment See Engine Compartment Overview in the Index for more information on location 6 28 Adding Coolant If you need more coolant add the proper DEX COOL coolant mixture at the surge tank but only when the engine is cool 1 PRU mandi Hosea Sessa e booad Basso 2 E ON OFF SELECT gt SELECT Y If the LOW ENGINE COOLANT DIC message comes When replacing the pressure cap make sure it on and stays on it means you re low on engine coolant is hand tight You can be burned if you spill coolant on hot engine parts Coolant contains ethylene glycol and it will burn if the engine parts are hot enough Don t spill coolant on a hot engine 6 29 Cooling System Pressure Cap The cooling system pressure cap is located on the surge tank NOTICE Your cooling system pressure cap is a 15 psi 105 kPa pressure type cap and must be tightly installed to prevent coolant loss and possible engine damage from overheating Power Steering Fluid When to Check Power Steering Fluid It is not necessary to regularly check power steering fluid unles
263. r DIC 2 66 NOTICE Do not operate the engine with the tachometer in the red area or when the message HOT REDUCE ENG RPM is displayed Engine damage may occur Warning Lights Gages and Indicators This part describes the warning lights and gages that may be on your vehicle The pictures will help you locate them Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement Paying attention to your warning lights and gages could also save you or others from injury Warning lights come on when there may be or is a problem with one of your vehicle s functions As you will see in the details on the next few pages some warning lights come on briefly when you start the engine just to let you know they re working If you are familiar with this section you should not be alarmed when this happens Gages can indicate when there may be or is a problem with one of your vehicle s functions Often gages and warning lights work together to let you know when there s a problem with your vehicle When one of the warning lights comes on and stays on when you are driving or when one of the gages shows there may be a problem check the section that tells you what to do about it Please follow this manual s advice Waiting to do repairs can be costly and even dangerous So please get to know your warning lights and gages They re a big help Yo
264. r bridges Sometimes the surface of a curve or an overpass may remain icy when the surrounding roads are clear If you see a patch of ice ahead of you brake before you are on it Try not to brake while you re actually on the ice and avoid sudden steering maneuvers If You re Caught in a Blizzard Tie ared cloth to your vehicle to alert police that you ve been stopped by the snow Put on extra clothing or wrap a blanket around you If you have no blankets or extra clothing make body insulators from newspapers burlap bags rags floor mats anything you can wrap around yourself or tuck under your clothing to keep warm If you are stopped by heavy snow you could be in a serious situation You should probably stay with your vehicle unless you know for sure that you are near help and you can hike through the snow Here are some things to do to summon help and keep yourself and your passengers safe e Turn on your hazard flashers You can run the engine to keep warm but be careful 4 27 Snow can trap exhaust gases under your vehicle This can cause deadly CO carbon monoxide gas to get inside CO could overcome you and kill you You can t see it or smell it so you might not know it is in your vehicle Clear away snow from around the base of your vehicle especially any that is blocking your exhaust pipe And check around again from time to time to be sure snow doesn t collect there Open a window just a li
265. r storage the jack must be raised until the screw end is flush with the edge of the jack Storing the Spare Tire and Tools SPARE TIRE COVER WRENCH JACK JACK CONTAINER ai Storing a jack a tire or other equipment in the l passenger compartment of the vehicle could cause injury In a sudden stop or collision loose equipment could strike someone Store all these in the proper place RETAINER The compact spare tire is for temporary use only Replace the compact spare tire with a full size tire as soon as you can See Compact Spare Tire later in this section See the storage instructions label to replace your compact spare into your trunk properly 5 27 Compact Spare Tire Although the compact spare tire was fully inflated when your vehicle was new it can lose air after a time Check the inflation pressure regularly It should be 60 psi 420 kPa After installing the compact spare on your vehicle you should stop as soon as possible and make sure your spare tire is correctly inflated The compact spare is made to perform well at speeds up to 65 mph 105 km h for distances up to 3 000 miles 5 000 km so you can finish your trip and have your full size tire repaired or replaced where you want You must calibrate the Check Tire Pressure System after installing or removing the compact spare See Check Tire Pressure System in the Index Of course it s best to replace your spare with a full size tire
266. re your vehicle for longer storage periods Also for your audio system see Theft Deterrent Feature in the Index Bulb Replacement Headlamps This section describes bulb changing procedures for For the proper bulb type see Replacement Bulbs in some of your interior and exterior lamps For any bulb the Index changing procedure not listed in this section contact your dealer s service department For the type of bulb to use see Replacement Bulbs in the Index Halogen Bulbs Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb You or others could be injured Be sure to read and follow the instructions on the bulb package 2 Use a large screwdriver by the outside mount to separate the lamp assembly from the outboard snap mounting pin Slide the headlamp assembly outward and lift it out 1 Remove the two bolts with a 10 mm socket 6 37 3 Disconnect the wiring harness from the headlamp assembly 4 Lift the tabs to remove the bulb from the assembly 5 Replace the bulb Push the bulb assembly in and turn it clockwise to install the bulb assembly into the headlamp assembly Then reconnect the wiring harness to the lamp assembly 6 Slide the lamp assembly back into place by lining up the track on the bottom of the assembly with the guide on the vehicle Then connect the outboard snap and secure the lamp assembly with the two bolts Your vehicle
267. reak and it can change the way your vehicle handles These could cause you to lose control and crash Also overloading can shorten the life of your vehicle NOTICE Your warranty does not cover parts or components that fail because of overloading If you put things inside your vehicle like suitcases tools packages or anything else they will go as fast as the vehicle goes If you have to stop or turn quickly or if there is a crash they ll keep going 4 30 Things you put inside your vehicle can strike and injure people in a sudden stop or turn or in a crash e Put things in the trunk of your vehicle In a trunk put them as far forward as you can Try to spread the weight evenly Never stack heavier things like suitcases inside the vehicle so that some of them are above the tops of the seats Don t leave an unsecured child restraint in your vehicle When you carry something inside the vehicle secure it whenever you can Electronic Level Control This feature keeps the rear of your vehicle level as the load changes It is automatic you don t need to adjust anything Towing a Trailer If you don t use the correct equipment and drive properly you can lose control when you pull a trailer For example if the trailer is too heavy the brakes may not work well or even at all You and your passengers could be seriously injured You may also damage your vehicle the resulting repairs would
268. reminder light and all your belts buckles latch plates retractors and anchorages are working properly Look for any other loose or damaged safety belt system parts If you see anything that might keep a safety belt system from doing its job have it repaired Torn or frayed safety belts may not protect you in a crash They can rip apart under impact forces If a belt is torn or frayed get a new one right away Also look for any opened or broken air bag covers and have them repaired or replaced The air bag system does not need regular maintenance 1 58 Replacing Restraint System Parts After a Crash If you ve had a crash do you need new belts After a very minor collision nothing may be necessary But if the belts were stretched as they would be if worn during a more severe crash then you need new belts If belts are cut or damaged replace them Collision damage also may mean you will need to have safety belt or seat parts repaired or replaced New parts and repairs may be necessary even if the belt wasn t being used at the time of the collision If your seat adjuster won t work after a crash the special part of the safety belt that goes through the seat to the adjuster may need to be replaced If an air bag inflates you ll need to replace air bag system parts See the part on the air bag system earlier in this section JD Section2 Features and Controls Here you can learn about the many standard an
269. rking brake hold the regular brake pedal down with your right foot and push the parking brake pedal with your left foot This will release the parking brake pedal When you lift your left foot the parking brake pedal will follow it to the release position If you try to drive approximately 20 feet 6 1 m with the parking brake on the brake light stays on and a chime sounds until you release the parking brake NOTICE Driving with the parking brake on can cause your rear brakes to overheat You may have to replace them and you could also damage other parts of your vehicle If you are towing a trailer and are parking on any hill see Towing a Trailer in the Index That section shows what to do first to keep the trailer from moving 2 29 Shifting Into PARK P It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK P with the parking brake firmly set Your vehicle can roll If you have left the engine running the vehicle can move suddenly You or others could be injured To be sure your vehicle won t move even when you re on fairly level ground use the steps that follow If you re pulling a trailer see Towing a Trailer in the Index 3 Turn the ignition key to LOCK 4 Remove the key and take it with you If you can 1 Hold the brake pedal down with your right foot and leave your vehicle with the ignition key in your set the parking brake by pushing down the parking
270. rs trunk ignition and glove box The VALET key only operates the doors and the ignition Both the master and VALET key have a transponder embedded into the key for security and vehicle theft deterrence The keys also come with a bar code tag Keep the bar code tag in a safe place If you lose your key you will be able to have a new one made using the bar code tag The replacement key must have a vehicle theft deterrent system transponder embedded in it NOTICE Your vehicle has a number of features that can help prevent theft But you can have a lot of trouble getting into your vehicle if you ever lock your keys inside You may even have to damage your vehicle to get in So be sure you have extra keys Door Locks Unlocked doors can be dangerous Passengers especially children can easily open the doors and fall out When a door is locked the inside handle won t open it Outsiders can easily enter through an unlocked door when you slow down or stop your vehicle This may not be so obvious You increase the chance of being thrown out of the vehicle in a crash if the doors aren t locked Wear safety belts properly lock your doors and you will be far better off whenever you drive your vehicle There are several ways to lock and unlock your vehicle From the outside use your key or remote lock control transmitter To unlock the door from the inside move the manual door lock control located above the
271. rtment immediately keep driving it until it can be scheduled for service unless of course the problem is safety related If it is please call your dealership let them know this and ask for instructions If the dealer requests that you simply drop the vehicle off for service you are urged to do so as early in the work day as possible to allow for same day repair Transportation Options Warranty service can generally be completed while you wait However if you are unable to wait Oldsmobile helps minimize your inconvenience by providing several transportation options Depending on the circumstances your dealer can offer you one of the following Shuttle Service Participating dealers can provide you with shuttle service to get you to your destination with minimal interruption of your daily schedule This includes a one way shuttle ride to a destination up to 10 miles from the dealership 8 8 Public Transportation or Fuel Reimbursement If your vehicle requires overnight warranty repairs reimbursement up to 30 per day five days maximum may be available for the use of public transportation such as taxi or bus In addition should you arrange transportation through a friend or relative reimbursement for reasonable fuel expenses up to 10 per day five day maximum may be available Claim amounts should reflect actual costs and be supported by original receipts Courtesy Rental Vehicle When your vehicle is unavailable
272. running With the parking brake applied place the shift lever in PARK P 6 24 With your foot on the brake pedal move the shift lever through each gear range pausing for about three seconds in each range Then position the shift lever in PARK P Let the engine run at idle for three to five minutes Then without shutting off the engine follow these steps 3 5L V6 Engine 4 0L V8 Engine See Engine Compartment Overview in the Index for more information on location 1 Pull out the dipstick and wipe it with a clean rag or paper towel 2 Push it back in all the way wait three seconds and How to Add Fluid then pull it back out again Refer to the Maintenance Schedule to determine what kind of transaxle fluid to use See Recommended Fluids and Lubricants in the Index If the fluid level is low add only enough of the proper fluid to bring the level into the cross hatched area on the dipstick 1 Pull out the dipstick 2 Using a long neck funnel add enough fluid at the dipstick hole to bring it to the proper level 3 5L V6 Engine It doesn t take much fluid generally less than one pint 0 5 L Don t overfill NOTICE We recommend you use only fluid labeled DEXRON TI because fluid with that label is made especially for your automatic transaxle 4 0L V8 Engine Damage caused by fluid other than DEXRON III is not covered by your new vehicle warranty 3 Check both sides
273. rvice Station Guide GENERAL MOTORS GM the GM Emblem OLDSMOBILE the OLDSMOBILE Rocket Emblem and the AURORA Emblem are registered trademarks of General Motors Corporation AURORA is used with the permission of Hankook Tire This manual includes the latest information at the time it was printed We reserve the right to make changes in the product after that time without further notice For vehicles first sold in Canada substitute the name General Motors of Canada Limited for Oldsmobile Division whenever it appears in this manual Please keep this manual in your vehicle so it will be there if you ever need it when you re on the road If you sell the vehicle please leave this manual in it so the new owner can use it vi We support voluntary technician certification AS CERTIFIED WE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION THROUGH National Institute for AUTOMOTIVE SERVICE EXCELLENCE S For Canadian Owners Who Prefer a French Language Manual Aux propri taires canadiens Vous pouvez vous procurer un exemplaire de ce guide en fran ais chez votre concessionaire ou au DGN Marketing Services Ltd 1577 Meyerside Dr Mississauga Ontario LST 1B9 How to Use this Manual Many people read their owner s manual from beginning to end when they first receive their new vehicle If you do this it will help you learn about the features and controls for your vehicle In this manual you
274. s That s why safety belts make such good sense 1 12 Here Are Questions Many People Ask About Safety Belts and the Answers Q A Won t I be trapped in the vehicle after an accident if I m wearing a safety belt You could be whether you re wearing a safety belt or not But you can unbuckle a safety belt even if you re upside down And your chance of being conscious during and after an accident so you can unbuckle and get out is much greater if you are belted If my vehicle has air bags why should I have to wear safety belts Air bags are in many vehicles today and will be in most of them in the future But they are supplemental systems only so they work with safety belts not instead of them Every air bag system ever offered for sale has required the use of safety belts Even if you re in a vehicle that has air bags you still have to buckle up to get the most protection That s true not only in frontal collisions but especially in side and other collisions Q If Pm a good driver and I never drive far from home why should I wear safety belts A You may be an excellent driver but if you re in an accident even one that isn t your fault you and your passengers can be hurt Being a good driver doesn t protect you from things beyond your control such as bad drivers Most accidents occur within 25 miles 40 km of home And the greatest number of serious injuries and deaths
275. s and the road you can have a very slippery situation You ll have a lot less traction or grip and will need to be very careful LZ What s the worst time for this Wet ice Very cold snow or ice can be slick and hard to drive on But wet ice can be even more trouble because it may offer the least traction of all 4 26 You can get wet ice when it s about freezing 32 F 0 C and freezing rain begins to fall Try to avoid driving on wet ice until salt and sand crews can get there Whatever the condition smooth ice packed blowing or loose snow drive with caution Keep your traction control system on It improves your ability to accelerate when driving on a slippery road Even though your vehicle has a traction control system you ll want to slow down and adjust your driving to the road conditions See Traction Control System in the Index Your anti lock brakes improve your vehicle s stability when you make a hard stop on a slippery road Even though you have the anti lock braking system you ll want to begin stopping sooner than you would on dry pavement See Anti Lock in the Index e Allow greater following distance on any slippery road Watch for slippery spots The road might be fine until you hit a spot that s covered with ice On an otherwise clear road ice patches may appear in shaded areas where the sun can t reach around clumps of trees behind buildings or unde
276. s because the back of the rear facing child restraint would be very close to the inflating air bag Always secure a rear facing child restraint in the rear seat 1 52 4 Buckle the belt Make sure the release button is 5 Pull the rest of the lap belt all the way out of the positioned so you would be able to unbuckle the retractor to set the lock safety belt quickly if you ever had to 1 53 6 To tighten the belt feed the lap belt back into the retractor while you push down on the child restraint You may find it helpful to use your knee to push down on the child restraint as you tighten the belt 7 Push and pull the child restraint in different directions to be sure it is secure To remove the child restraint just unbuckle the vehicle s safety belt and let it go back all the way The safety belt will move freely again and be ready to work for an adult or larger child passenger Older Children Older children who have outgrown booster seats should wear the vehicle s safety belts If you have the choice a child should sit next to a window so the child can wear a lap shoulder belt and get the additional restraint a shoulder belt can provide 1 54 llls Q What is the proper way to wear safety belts A If possible an older child should wear a lap shoulder belt and get the additional restraint a shoulder belt can provide The should belt should not cross the face or neck The lap belt should fit snugly be
277. s find this to be too much trouble and don t use cruise control on steep hills Ending Cruise Control Without Erasing the Set Speed There are two ways to turn off the cruise control Step lightly on the brake pedal or pull the cruise lever towards you to cancel cruise To resume the set speed see Resuming a Set Speed earlier in this section Erasing Cruise Control Speed Memory When you turn off the cruise control or the ignition your cruise control set speed memory is erased 2 44 Exterior Lamps Headlamps See Turn Signal Multifunction Lever in the Index Daytime Running Lamps Daytime Running Lamps DRL can make it easier for others to see the front of your vehicle during the day DRL can be helpful in many different driving conditions but they can be especially helpful in the short periods after dawn and before sunset Fully functional daytime running lights are required on all vehicles first sold in Canada A light sensor on top of the instrument panel makes the DRL work so be sure it isn t covered The DRL system will make your high beam headlamps come on at reduced brightness in daylight when the following conditions are met The ignition is on the headlamp switch is off and the transaxle is not in PARK P When the DRL are on only your high beam headlamps will be on The parking lamps taillamps sidemarker and other lamps won t be on With your headlamp control in AUT
278. s instrument panel Your driver information center will also display messages about engine overheating See Engine Coolant Temperature Gage in the Index Overheated Engine Protection Operating Mode Should an overheated engine condition exist and the message HOT STOP ENGINE is displayed an overheat protection mode which alternates firing groups of cylinders helps prevent engine damage In this mode you will notice a loss in power and engine performance This operating mode allows your vehicle to be driven to a safe place in an emergency you may drive up to 50 miles 80 km Towing a trailer in the overheat protection mode should be avoided NOTICE After driving in the overheated engine protection operating mode to avoid engine damage allow the engine to cool before attempting any repair The engine oil will be severely degraded Repair the cause of coolant loss change the oil and reset the oil life indicator See Engine Oil in the Index If Steam Is Coming From Your Engine 5 10 Steam from an overheated engine can burn you badly even if you just open the hood Stay away from the engine if you see or hear steam coming from it Just turn it off and get everyone away from the vehicle until it cools down Wait until there is no sign of steam or coolant before you open the hood If you keep driving when your engine is overheated the liquids in it can catch fire You or others could be badly burned Sto
279. s take care to wipe off any overspray or splash from all painted surfaces on the body or wheels of the vehicle Petroleum based products may damage the paint finish and tires 6 63 Sheet Metal Damage If your vehicle is damaged and requires sheet metal repair or replacement make sure the body repair shop applies anti corrosion material to the parts repaired or replaced to restore corrosion protection Original manufacturer replacement parts will provide the corrosion protection while maintaining the warranty Finish Damage Any stone chips fractures or deep scratches in the finish should be repaired right away Bare metal will corrode quickly and may develop into a major repair expense Minor chips and scratches can be repaired with touch up materials available from your dealer or other service outlets Larger areas of finish damage can be corrected in your dealer s body and paint shop Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody If these are not removed accelerated corrosion rust can occur on the underbody parts such as fuel lines frame floor pan and exhaust system even though they have corrosion protection 6 64 At least every spring flush these materials from the underbody with plain water Clean any areas where mud and other debris can collect Dirt packed in closed areas of the frame should be loosened before being flushed Your dealer or an u
280. s you suspect there is a leak in the system or you hear an unusual noise A fluid loss in this system could indicate a problem Have the system inspected and repaired See Engine Compartment Overview in the Index for more information on location How to Check Power Steering Fluid Turn the key off let the engine compartment cool down wipe the cap and the top of the reservoir clean then unscrew the cap and wipe the dipstick with a clean rag Replace the cap and completely tighten it Then remove the cap again and look at the fluid level on the dipstick The level should be at the FULL COLD mark If necessary add only enough fluid to bring the level up to the mark What to Use To determine what kind of fluid to use see Recommended Fluids and Lubricants in the Index Always use the proper fluid Failure to use the proper fluid can cause leaks and damage hoses and seals Windshield Washer Fluid Open the cap labeled WASHER FLUID Add washer fluid until the tank is full What to Use When you need windshield washer fluid be sure to read NOTICE the manufacturer s instructions before use If you will be operating your vehicle in an area where the temperature may fall below freezing use a fluid that has sufficient protection against freezing When using concentrated washer fluid follow the manufacturer s instructions for adding water Adding Washer Fluid Don t mix water with ready to use washer fluid
281. saxle clothing and tools away from any underhood in PARK P and a manual transaxle in NEUTRAL electric fan before setting the parking brake 5 Find the positive and negative terminals on each battery or remote terminal You should always use the remote positive terminal instead of the positive terminal on your battery Using a match near a battery can cause battery gas to explode People have been hurt doing this and some have been blinded Use a flashlight if you need more light a O oe ee Be sure the battery has enough war You don t terminal cover away need to add water to the ACDelco battery from the relay center installed in every new GM vehicle But if a battery has filler caps be sure the right amount of fluid is there If it is low add water to take care of that first If you don t explosive gas could be present See Engine Compartment Overview in the Index for more information on location Battery fluid contains acid that can burn you Don t get it on you If you accidentally get it in your eyes or on your skin flush the place with water and get medical help immediately 6 Check that the jumper cables don t have loose or missing insulation If they do you could get a shock The vehicles could also be damaged Before you connect the cables here are some things you should know Positive will go to positive and negative will go to a heavy unpainted m
282. se safety restraints In fact the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle Infants and Young Children Every time infants and young children ride in vehicles they should have the protection provided by the appropriate restraint Young children should not use the vehicle s safety belts unless there is no other choice For example in a crash at only 25 mph 40 km h a 12 Ib 5 5 kg baby will suddenly become a 240 Ib 110 kg force on a person s arms A baby should be secured in an appropriate restraint People should never hold a baby in their arms while riding in a vehicle A baby doesn t weigh much until a crash During a crash a baby will become so heavy it is not possible to hold it CAUTION Continued 1 39 Children who are up against or very close to any air bag when it inflates can be seriously injured or killed Air bags plus lap shoulder belts offer outstanding protection for adults and older children but not for young children and infants Neither the vehicle s safety belt system nor its air bag system is designed for them Young children and infants need the protection that a child restraint system can provide 1 40 Q What are the different types of add on child restraints Add on child restraints which are purchased by the vehicle s owner are available in four basic types Sele
283. see this message try to reset the system stop turn off the engine then start the engine again If the SERV STABILITY SYS message still comes on it means there is a problem You should see your dealer for service Reduce your speed and drive accordingly STABILITY ACTIVE 42 You may see the STABILITY ACTIVE message on the Driver Information Center It means that an advanced computer controlled system has come on to help your vehicle continue to go in the direction in which you re steering This stability enhancement system activates when the computer senses that your vehicle is just starting to spin as it might if you hit a patch of ice or other slippery spot on the road When the system is on you may hear a noise or feel a vibration in the brake pedal This is normal When the STABILITY ACTIVE message is on you should continue to steer in the direction you want to go The system is designed to help you in bad weather or other difficult driving situations by making the most of whatever road conditions will permit If the STABILITY ACTIVE message comes on you ll know that something has caused your vehicle to start to spin so you should consider slowing down 2 91 SD Section 3 Comfort Controls and Audio Systems In this section you ll find out how to operate the comfort control and audio systems offered with your vehicle Be sure to read about the particular systems supplied with your vehicle 3 2 Comfort Contro
284. selected in all manual airflow modes except front defrost When the weather is cool or damp operating in RECIRC for extended periods of time may cause fogging of the vehicle s windows To clear the fog switch back to outside air by turning off RECIRC select either DEFOG or front defrost mode and increase the fan speed To avoid refogging of the windows minimize your use of RECIRC under these conditions and turn the A C on to help dehumidify the air x A C Press this button to turn the air conditioning compressor on and off If the system is operating in the automatic mode the A C indicator light will automatically illuminate In the auto mode the A C compressor will only operate when the system determines it is needed OFF Turn the AUTO PUSH knob to OFF Turning the system off will cause the fan to turn off and the airflow to be directed out the lower floor outlets The system will still try to keep the interior of the vehicle at the previously chosen comfort setting The outside temperature will show in the display when the system is set to OFF Air Conditioning The air conditioner cools and dehumidifies the air for the inside of the vehicle The air conditioning compressor is enabled in all modes unless the A C button is in the off position the indicator light will not be illuminated However the air conditioning compressor will not operate when the outside temperature is below 34 F 1 C When the air condition
285. side of each front seat If you would like your stored driving or exit position to be recalled when unlocking your vehicle with the transmitter see DIC Personalization in the Index Heated Front Seat Option The heated seat controls are located next to the console shifter Push the ON part of the button once for a HI setting or twice for a LO setting Push the OFF part of the button to turn the heated seat off The LO setting warms the seatback and cushion until the seat approximates body temperature The HI setting heats the seatback and cushion to a slightly higher temperature The heated seats can only be used when the ignition is turned on The heating elements in the seats automatically turn off when the vehicle s ignition is turned off Reclining Front Seatbacks If your vehicle has a power recliner the vertical control described previously in this section reclines the front seatbacks If your vehicle has the manual recliner lift the lever on the outboard side of the seat and move the seatback to the desired position Release the lever to lock the seatback Pull up on the lever and the seat will go to an upright position 1 6 But don t have a seatback reclined if your vehicle is moving Sitting in a reclined position when your vehicle is in motion can be dangerous Even if you buckle up your safety belts can t do their job when you re reclined like this The shoulder belt can t do
286. slider control is in the AUTO position when any door is opened all of the vehicles courtesy lamps will come on See Reading Lamps in the Index They make it easier for you to enter and leave the vehicle The courtesy lamps will remain on for about 25 seconds after all doors have been closed They will then theater dim to off Move the front reading lamp slider control in the overhead console to ON to turn on the interior courtesy lamps When the control is moved back to either OFF or AUTO the courtesy lamps will immediately turn off If the control is OFF when the doors are opened only the lower instrument panel courtesy lamps will come on Also if the control is OFF when illuminated entry or delayed exit lighting are active only the lower instrument panel courtesy lamps will be on If a door is left ajar your interior lamps will turn off after 10 minutes to save your battery Illuminated Entry If it is dark enough outside and you press the unlock symbol on the remote lock control transmitter while all doors are closed the interior courtesy lamps will come on and stay on for approximately 40 seconds When the 40 seconds is up the lights will be turned off by the theater dimming effect The lamps will turn off immediately by pressing the lock symbol on the remote lock control transmitter by turning the ignition key to RUN or by activating the power door locks Delayed Entry Lighting When you open the door to enter your v
287. sound when it should but the vehicle s lamps flash check to see if the horn works The horn fuse may be blown See Fuses and Circuit Breakers in the Index If the alarm does not sound or the vehicle s lamps do not flash the vehicle should be serviced by an authorized service center 2 18 PASS Key II Your vehicle is equipped with the PASS Key III Personalized Automotive Security System theft deterrent system PASS Key III is a passive theft deterrent system This means you don t have to do anything different to arm or disarm the system It works when you insert or remove the key from the ignition Your PASS Key III system operates on a radio frequency subject to Federal Communications Commission FCC Rules and with Industry Canada This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This device complies with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Changes or modifications to this system by other than an authorized service facility could void authorization to use th
288. stance Information booklet for information on the Canadian Motor Vehicle Arbitration Plan CAMVAP The BBB Auto Line Program is an out of court program administered by the Council of Better Business Bureaus to settle automotive disputes regarding vehicle repairs or the interpretation of the New Vehicle Limited Warranty Although you are required to resort to this informal dispute resolution program prior to filing any court action use of the program is free of charge and your case will generally be heard within 40 days If you do not agree with the decision given in your case you may reject it and proceed with any other venue for relief available to you You may contact the BBB using the toll free telephone number or write them at the following address BBB Auto Line Council of Better Business Bureaus Inc 4200 Wilson Boulevard Suite 800 Arlington VA 22203 1804 Telephone 1 800 955 5100 This program is available in all 50 states and the District of Columbia Eligibility is limited by vehicle age mileage and other factors General Motors reserves the right to change eligibility limitations and or discontinue its participation in this program Customer Assistance for Text Telephone TTY Users To assist customers who are deaf hard of hearing or speech impaired and who use Text Telephones TTYs Oldsmobile has TTY equipment available at its Customer Assistance Network Any TTY user can communicate with Oldsmobile by dia
289. t the same interval after 150 000 miles 240 000 km See Owner Checks and Services and Periodic Maintenance Inspections following Footnotes The U S Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle s useful life We however urge that all recommended maintenance services be performed at the indicated intervals and the maintenance be recorded A good time to check your brakes is during tire rotation See Brake System Inspection under Periodic Maintenance Inspections in Part C of this schedule 7 5 Scheduled Maintenance Engine Oil Scheduled Maintenance Change engine oil and filter as indicated by the GM Oil Life System or every 12 months whichever occurs first Reset the indicator The system will show you when to change the oil usually between 3 000 miles 5 000 km and 10 000 miles 16 000 km since your last oil change Under severe conditions the indicator may come on before 3 000 miles 5 000 km Never drive your vehicle more than 10 000 miles 16 000 km or 12 months without an oil and filter change 7 6 The system won t detect dust in the oil So if you drive in a dusty area be sure to change your oil and filter every 3 000 miles 5 000 km or sooner if the CHANGE OIL SOON or the CHANG
290. tations during REV operation by using the TUNE knob FWD 2 Press this button to advance quickly to another part of the tape Press the button again to return to playing speed The radio will play the last selected station while the tape advances You may select stations during FWD operation by using the TUNE knob DMO 3 Press this button to reduce background noise DOLBY B ON will appear on the display with the Dolby icon Press it again to turn Dolby off Dolby Noise Reduction is manufactured under a license from Dolby Laboratories Licensing Corporation Dolby and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation SIDE 5 Press this button to play the other side of the tape AUTO EQ Press AUTO EQ to select the desired preset equalization setting while playing a cassette tape The equalization will be automatically set whenever you play a cassette tape SEEK Press the up or down arrow to search for the next or previous selection on the tape Your tape must have at least three seconds of silence between each selection for SEEK to work You can skip nine selections up or down on the tape Choose how many selections you want to skip Press the SEEK arrow that many times The number of selections to be skipped will appear on the display SCAN Press and hold the SEEK button for more than two seconds until you hear a beep and SCAN appears in the display Use SCAN to listen to each selection for a
291. te Lamps Instrument Panel Lights Turning the headlamp control to AUTO will turn the headlamps taillamps and parking lamps on and off while the ignition is on by sensing how dark it is outside Turn the headlamp control back to off to turn all of the lamps off Wiper Activated Headlamps This feature turns on the low beam headlamps instrument panel cluster backlighting and taillamps when it is bright enough outside the headlamp control is in AUTO and after the windshield wipers have been in use for approximately six seconds To operate the wiper activated headlamps the headlamp control must be in AUTO If the wiper activated headlamps are on and the ignition switch is turned to RUN the wiper activated headlamps will continue When you turn the key to LOCK the wiper activated headlamps will immediately turn off The wiper activated headlamps will also turn off if you turn the headlamp switch to OFF or turn off the windshield wipers Headlamp High Low Beam Changer To change the headlamps from low beam to high push the lever away from you until you hear a click Then release it When the high beams are on this light on the instrument panel cluster will also be on If the fog lamps are on when you turn on the high beam headlamps the fog lamps will turn off The fog lamps will turn back on when you turn off the high beam headlamps 2 37 Lamps On Reminder If the headlamp switch is left on you ll hear a warn
292. th the ignition on or off In addition the clock can also be automatically set when tuned to an RDS station that is broadcasting time by pressing and holding the HR and the MN button at the same time The display will show TIME UPDATED If there is no time available NO UPDATE will be displayed AM FM Stereo with Cassette Tape and Compact Disc Player with Programmable Equalization and Radio Data System RDS Playing the Radio VOLUME POWER Press this knob to turn the system on and off To increase volume turn the knob clockwise Turn it counterclockwise to decrease volume SCV Your system has a feature called Speed Compensated Volume SCV With SCV your audio system adjusts automatically to make up for road and wind noise as you drive Set the volume at the desired level Press this button to select MIN MED or MAX Each choice allows for more volume compensation at faster vehicle speeds Then as you drive SCV automatically increases the volume as necessary to overcome noise at any particular speed The volume level should always sound the same to you as you drive If you don t want to use SCV select OFF Finding a Station AM FM Press this button to switch between AM FM1 and FM2 The display shows your selection TUNE Turn this knob to select radio stations SEEK Press the up or down arrow to go to the next higher or lower station and stay there The sound will mute while seeking SCAN Press and hold the
293. the parking lamp position Dimming of the instrument panel display is not possible during daylight hours The instrument panel display can only be adjusted when the parking lamps are on and it is dark outside Perimeter Lighting When the unlock symbol on the remote lock control transmitter is pressed the DRL headlamps parking lamps and back up lamps will turn on for approximately 25 seconds if it is dark enough outside This feature can be programmed on or off for each transmitter You can also program how long the exterior lamps will stay on after unlocking the vehicle You must program this feature through the Driver Information Center DIC See DIC Personalization Programming in the Index 2 48 Front Reading Lamps These lamps and the interior courtesy lamps will come on when you open a door They will turn off when you turn on the ignition If a door is left open they will turn off after about 10 minutes To turn on the reading lamps when the doors are closed press the button under the lamp you want on Press it again to turn the lamp off These lamps work even when the ignition is off To avoid draining your vehicle s battery be sure to turn off all front and rear reading lamps when leaving your vehicle Rear Reading Lamps These lamps will come on when you open the doors You can also turn them on by pressing the button on the side of the lamp Press it again to turn them off Inadvertent Power B
294. to fill it enough to put the level somewhere in the proper operating range Push the dipstick all the way back in when you re through What Kind of Engine Oil to Use Oils recommended for your vehicle can be identified by looking for the starburst symbol This symbol indicates that the oil has been certified by the American Petroleum Institute API Do not use any oil which does not carry this starburst symbol If you change your own oil be sure you use oil that has the starburst symbol on the front of the oil container If you have your oil changed for you be sure the oil put into your engine is American Petroleum Institute certified for gasoline engines You should also use the proper viscosity oil for your vehicle as shown in the following chart 6 17 RECOMMENDED SAE VISCOSITY GRADE ENGINE OILS FOR BEST FUEL ECONOMY AND COLD STARTING SELECT THE LOWEST SAE VISCOSITY GRADE OIL FOR THE EXPECTED TEMPERATURE RANGE HOT FOR THIS WEATHER SYMBOL SAE 10W 30 SAE 5W 30 PREFERRED COLD WEATHER DO NOT USE SAE 20W 50 OR ANY OTHER GRADE OIL NOT RECOMMENDED 6 18 As shown in the chart SAE 5W 30 is best for your vehicle However you can use SAE 10W 30 if it s going to be 0 F 18 C or above These numbers on an oil container show its viscosity or thickness Do not use other viscosity oils such as SAE 20W 50 NOTICE Use only engine oil with the American Petroleum Institute Certified For Gasoli
295. towing a trailer so there is less shifting between gears or when going down a steep hill 2 28 SECOND 2 This position gives you more power but lower fuel economy than AUTOMATIC OVERDRIVE D or THIRD 3 You can use SECOND 2 on hills It can help control your speed as you go down steep mountain roads but then you would also want to use your brakes off and on FIRST 1 This position gives you even more power but lower fuel economy than SECOND 2 You can use it on very steep hills or in deep snow or mud If the selector lever is put in FIRST 1 the transaxle won t shift into FIRST 1 until the vehicle is going slowly enough NOTICE If your front wheels can t turn don t try to drive This might happen if you were stuck in very deep sand or mud or were up against a solid object You could damage your transaxle Also if you stop when going uphill don t hold your vehicle there with only the accelerator pedal This could overheat and damage the transaxle Use your brakes or shift into PARK P to hold your vehicle in position on a hill Parking Brake Cer Your vehicle has a PUSH TO RELEASE parking brake To set the parking brake hold the regular brake pedal down with your right foot Push down the parking brake pedal with your left foot If the ignition is on the brake system warning light will come on while the parking brake is set and a single chime will be heard To release the pa
296. ttle on the side of the vehicle that s away from the wind This will help keep CO out Run your engine only as long as you must This saves fuel When you run the engine make it go a little faster than just idle That is push the accelerator slightly 4 28 This uses less fuel for the heat that you get and it keeps the battery charged You will need a well charged battery to restart the vehicle and possibly for signaling later on with your headlamps Let the heater run for a while Then shut the engine off and close the window almost all the way to preserve the heat Start the engine again and repeat this only when you feel really uncomfortable from the cold But do it as little as possible Preserve the fuel as long as you can To help keep warm you can get out of the vehicle and do some fairly vigorous exercises every half hour or so until help comes Recreational Vehicle Towing Your vehicle was not designed to be towed with all four wheels on the ground If your vehicle must be towed see Towing Your Vehicle in the Index NOTICE Towing your vehicle with all four wheels on the ground will damage drivetrain components Loading Your Vehicle Ha S TIRE LOADING INFORMATION OCCUPANTS VEHICLE CAP FRT CTR RR TOTAL K L MAX LOADING GVWR SAME AS 200 D TIRE PRESSURE OT ADD 28KPA 4PS S MANUAL FOR MORE INFORM
297. ully at the factory to give you the longest tire life and best overall performance Scheduled wheel alignment and wheel balancing are not needed However if you notice unusual tire wear or your vehicle pulling one way or the other the alignment may need to be reset If you notice your vehicle vibrating when driving on a smooth road your wheels may need to be rebalanced Wheel Replacement Replace any wheel that is bent cracked or badly rusted or corroded If wheel nuts keep coming loose the wheel wheel bolts and wheel nuts should be replaced If the wheel leaks air replace it except some aluminum wheels which can sometimes be repaired See your dealer if any of these conditions exist Your dealer will know the kind of wheel you need 6 55 Each new wheel should have the same load carrying capacity diameter width offset and be mounted the same way as the one it replaces If you need to replace any of your wheels wheel bolts or wheel nuts replace them only with new GM original equipment parts This way you will be sure to have the right wheel wheel bolts and wheel nuts for your vehicle Using the wrong replacement wheels wheel bolts or wheel nuts on your vehicle can be dangerous It could affect the braking and handling of your vehicle make your tires lose air and make you lose control You could have a collision in which you or others could be injured Always use the correct wheel wheel bolts and wheel nuts
298. ur abdomen This could Pull up on the latch plate to make sure it is secure If the belt isn t long enough see Safety Belt Extender at the end of this section Make sure the release button on the buckle is cause serious or even fatal injuries The shoulder belt positioned so you would be able to unbuckle the should go over the shoulder and across the chest safety belt quickly if you ever had to These parts of the body are best able to take belt restraining forces The safety belt locks if there s a sudden stop or crash or if you pull the belt very quickly out of the retractor Oh i W gt lt 2 NK fa Fd 1 15 Q What s wrong with this You can be seriously hurt if your shoulder belt is too loose In a crash you would move forward too much which could increase injury The shoulder belt should fit against your body OOF E P A al F A SQ The shoulder belt is too loose It won t give nearly as much protection this way 1 16 Q What s wrong with this You can be seriously injured if your belt is buckled in the wrong place like this In a crash the belt would go up over your abdomen The belt forces would be there not at the pelvic bones This could cause serious internal injuries Always buckle your belt into the buckle nearest you The belt is buckled in the wrong pla
299. ur vehicle has a Driver Information Center that works along with the warning lights and gages See Driver Information Center in the Index Safety Belt Reminder Light When the key is turned to RUN or START a chime will come on for about eight seconds to remind people to fasten their safety belts The safety belt light will also come on and stay on for about 20 seconds then flash for about 55 seconds If the driver s belt is already buckled the chime will not sound and the light will go off after 5 seconds 2 67 Air Bag Readiness Light There is an air bag readiness light on the instrument panel which shows the air bag symbol The system checks the air bag s electrical system for malfunctions The light tells you if there is an electrical problem The system check includes the air bag sensors the air bag modules the wiring and the crash sensing and diagnostic module For more information on the air bag system see Air Bag in the Index This light will come on when you start your vehicle and it will flash for a few seconds Then the light should go out This means the system is ready If the air bag readiness light stays on after you start the vehicle or comes on when you are driving your air bag system may not work properly Have your vehicle serviced right away 2 68 If the air bag readiness light stays on after you start your vehicle it means the air bag system may not be working properly
300. usty areas indicate that the filter may need to be replaced early The filter should be replaced as part of the routine scheduled maintenance See Maintenance Schedule in the Index for more information air filter is located on the passenger side at the base of the windshield and can be accessed through a hood of the vehicle Overview in the Index for more information on location 6 22 The passenger compartment removable panel under the See Engine Compartment To check or replace the air filter 1 With the hood open unlatch and remove the access panel To remove the filter press on the spring tab on the side of the filter housing and pull the filter out of the housing 3 To install the new filter press on the spring tab and insert the filter into the housing The filter should be fully inserted into the upper and lower grooves and locked into place by the spring tab Reinstall the air filter access panel at the base of the windshield Automatic Transaxle Fluid When to Check and Change A good time to check your automatic transaxle fluid level is when the engine oil is changed Change both the fluid and filter every 50 000 miles 83 000 km if the vehicle is mainly driven under one or more of these conditions Jn heavy city traffic where the outside temperature regularly reaches 90 F 32 C or higher In hilly or mountainous terrain When doing frequent trailer towi
301. vehicle The air bag supplements the protection provided by safety belts Air bags distribute the force of the impact more evenly over the occupant s upper body stopping the occupant more gradually But the frontal air bags would not help you in many types of collisions including rollovers rear impacts and side impacts primarily because an occupant s motion is not toward the air bag Side impact air bags would not help you in many types of collisions including frontal or near frontal collisions rollovers and rear impacts primarily because an occupant s motion is not toward those air bags Air bags should never be regarded as anything more than a supplement to safety belts and then only in moderate to severe frontal or near frontal collisions for the driver s and right front passenger s frontal air bags and only in moderate to severe side collisions for the driver s and right front passenger s side impact air bags What will you see after an air bag inflates After an air bag inflates it quickly deflates so quickly that some people may not even realize the air bag inflated Some components of the air bag module the steering wheel hub for the driver s air bag the instrument panel for the right front passenger s bag the side of the seatback closest to the door for the driver and right front passenger s side impact air bags will be hot for a short time The parts of the bag that come into contact with you
302. vice or parts manager contact the owner of the dealership or the general manager STEP TWO If after contacting a member of dealership management it appears your concern cannot be resolved by the dealership without further help contact the Oldsmobile Customer Assistance Network by calling 1 800 442 6537 In Canada contact GM of Canada Customer Communication Centre in Oshawa by calling 1 800 263 3777 English or 1 800 263 7854 French We encourage you to call the toll free number in order to give your inquiry prompt attention Please have the following information available to give the Customer Assistance Representative Vehicle Identification Number This is available from the vehicle registration or title or the plate at the top left of the instrument panel and visible through the windshield Dealership name and location Vehicle delivery date and present mileage When contacting Oldsmobile please remember that your concern will likely be resolved at a dealer s facility That is why we suggest you follow Step One first if you have a concern STEP THREE Both General Motors and your dealer are committed to making sure you are completely satisfied with your new vehicle However if you continue to remain unsatisfied after following the procedure outlined in Steps One and Two file with the GM BBB Auto Line Program to enforce any additional rights you may have Canadian owners refer to your Warranty and Owner Assi
303. ving Even when the engine is not running you can use RUN to operate your electrical power accessories and to display some instrument panel warning lights START D This position starts your engine When the engine starts release the key The ignition switch will return to RUN for normal driving 2 21 Key Reminder Warning If you leave your key in the LOCK ignition position you will hear a warning chime when you open the driver s door Always leave your key in LOCK If you leave it in any other position you will drain the battery power Retained Accessory Power RAP After you turn the ignition off and remove the key you will still have electrical power to accessories such as the power windows audio steering wheel controls clock sunroof option accessory power outlet and the radio for up to 10 minutes The instrument panel cluster lights will stay on for a few seconds then go out Once you open a door the power will shut off 2 22 Starting Your Engine Move your shift lever to PARK P or NEUTRAL N Your engine won t start in any other position that s a safety feature To restart when you re already moving use NEUTRAL N only NOTICE Don t try to shift to PARK P if your vehicle is moving If you do you could damage the transaxle Shift to PARK P only when your vehicle is stopped Starting Your 3 5L V6 Engine 3 If your engine still won t start or starts but then stops
304. ward the front of the vehicle To Reinstall the Rear Seat Cushion 6 71 3 With the seat cushion lowered push rearward and then press down on the seat cushion until the spring locks on both ends engage A safety belt that isn t properly routed through 4 Check to make sure the safety belts are properly the seat cushion or is twisted won t provide the protection needed in a crash If the safety belt routed and that no portion of any safety belt is trapped under the seat Also make sure the seat cushion is secured hasn t been routed through the seat cushion at all it won t be there to work for the next Rear Underseat Bussed Electrical Center BEC passenger The person sitting in that position could be badly injured After reinstalling the seat cushion always check to be sure that the safety belts are properly routed and are not twisted The rear BEC is located beneath the rear seat on the driver s side The rear seat cushion must be removed to access the BEC See Removing the Rear Seat Cushion in the Index 1 Buckle the center passenger position safety belt and then route the safety belts through the proper slots in the seat cushion Don t let the safety belt get twisted 2 Slide the rear of the cushion up and under the seatback so the rear locating guides hook into the wire loops on the back frame en n 65 61 m 60 70 7
305. xperienced and able service experts in Oldsmobile dealerships all across North America They Il be ready and willing to help if you need it 4 22 Here are some things you can check before a trip Windshield Washer Fluid Is the reservoir full Are all windows clean inside and outside Wiper Blades Are they in good shape Fuel Engine Oil Other Fluids Have you checked all levels Lamps Are they all working Are the lenses clean Tires They are vitally important to a safe trouble free trip Is the tread good enough for long distance driving Are the tires all inflated to the recommended pressure Weather Forecasts What s the weather outlook along your route Should you delay your trip a short time to avoid a major storm system Maps Do you have up to date maps Highway Hypnosis Is there actually such a condition as highway hypnosis Or is it just plain falling asleep at the wheel Call it highway hypnosis lack of awareness or whatever There is something about an easy stretch of road with the same scenery along with the hum of the tires on the road the drone of the engine and the rush of the wind against the vehicle that can make you sleepy Don t let it happen to you If it does your vehicle can leave the road in less than a second and you could crash and be injured What can you do about highway hypnosis First be aware that it can happen Then here are some tips Make sure your veh
306. you still have the warning turn off the engine and get everyone out of the vehicle until it cools down Also see Overheated Engine Protection Operating Mode listed previously in this section You may decide not to lift the hood but to get service help right away 5 11 Cooling System When you decide it s safe to lift the hood here s what you ll see A Coolant Surge Tank with Pressure Cap B Two Electric Engine Cooling Fans 5 12 An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you Keep hands clothing and tools away from any underhood electric fan If the coolant inside the coolant surge tank is boiling don t do anything else until it cools down A low coolant level should be indicated by a CHECK COOLANT LEVEL message on the Driver Information NOTICE Center If it is you may have a leak in the radiator hoses heater hoses radiator water pump or somewhere When adding coolant it is important that you 9 else in the cooling system use only DEX COOL silicate free coolant If coolant other than DEX COOL is added to the system premature engine heater core or radiator corrosion may result In addition the engine coolant will require change sooner at 30 000 miles 50 000 km or 24 months whichever occurs first Damage caused by the use of coolant other than DEX COOL is not covered by your new vehicle warranty Heater a
307. your vehicle back and forth to get out of snow ice or sand without damaging your transaxle see Stuck In Sand Mud Ice or Snow in the Index NEUTRAL N In this position your engine doesn t connect with the wheels To restart when you re already moving use NEUTRAL N only Also use NEUTRAL N when your vehicle is being towed Shifting out of PARK P or NEUTRAL N while your engine is racing running at high speed is dangerous Unless your foot is firmly on the brake pedal your vehicle could move very rapidly You could lose control and hit people or objects Don t shift out of PARK P or NEUTRAL N while your engine is racing NOTICE Damage to your transaxle caused by shifting out of PARK P or NEUTRAL N with the engine racing isn t covered by your warranty 2 27 AUTOMATIC OVERDRIVE D This position is for normal driving If you need more power for passing and you re Going less than approximately 35 mph 55 km h push your accelerator pedal about halfway down Going about 35 mph 55 km h or more push the accelerator all the way down You ll shift down to the next gear and have more power THIRD 3 This position is also used for normal driving however it offers more power and lower fuel economy than AUTOMATIC OVERDRIVE D Here are some times you might choose THIRD 3 instead of AUTOMATIC OVERDRIVE D When driving on hilly winding roads when

2001 oldsmobile aurora owner`s manual

Contents

Download Pdf Manuals

Related Search

Related Contents